Introduction 4Instrument Cluster 12Warning and control lights 12Gauges 16Entertainment Systems 19AM/FM stereo cassette 19AM/FM stereo with CD 25AM/FM
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war
If... Then...The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition...The BeltMinder feature will notactivate.The fo
Reasons given... Consider...“The people I’m with don’twear belts”Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE peop
• The parklamps/headlamps are in OFF position (If vehicle is equippedwith Autolamps, this will not affect the procedure).To reduce the risk of injury,
Safety belt extension assemblyIf the safety belt is too short when fully extended, there is a 20 cm (8inch) safety belt extension assembly that can be
AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and righ
The National Highway Traffic Safety Administration (NHTSA)recommends a minimum distance of at least 25 cm (10 inches)between an occupant’s chest and t
Children and air bagsFor additional important safety information, read all information onsafety restraints in this guide.Children must always be prope
temporary hearing loss. Because air bags must inflate rapidly and withconsiderable force, there is the risk of death or serious injuries such asfractu
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
A difficulty with the system is indicated by one or more of the following:• The readiness lights will eitherflash or stay lit.• The readiness lights w
Turning the passenger air bag off1. Insert the ignition key, turn theswitch to OFF position and hold inOFF position while removing thekey.2. When the
Turning the passenger air bag back onThe passenger air bag remains OFF until you turn it back ON.1. Insert the ignition key and turnthe switch to ON.2
Always transport children who are 12 and younger in the rearseat. Always use safety belts and child restraints properly. If achild in a rear facing in
• the child has a medical condition which, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the dr
Important child restraint precautionsYou are required by law to use safety restraints for children in the U.S.and Canada. If small children (generally
Booster seats position a child so that safety belts fit better. They lift thechild up so that the lap belt rests low across the hips and the kneesbend
• Those with a high back.If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo
SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully fo
• Put the safety belt in the automatic locking mode. Refer to Automaticlocking mode (passenger side front and outboard rear seatingpositions-Regular C
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterHarley—Davidson instrument clusterWarning lights and gauges can alert y
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a
Installing child safety seats in the front row lap belt seatingpositions1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that itsbot
Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a
• F150 SuperCrew with quad bucketsTether strap attachment1. Position the child safety seat on the seat cushion.2. Route the child safety seat tether s
• Rear seats ( with quad bucketsonly)• Rear seats (SuperCrew only)If the tether strap is clippedincorrectly, the child safetyseat may not be retained
If the safety seat is not anchored properly, the risk of a childbeing injured in a collision greatly increases.Tether strap attachment rear SuperCab o
3. Install the child safety seat tightlyusing the safety belts. Follow theinstructions in this chapter.4. Tighten the tether strapaccording to the chi
• F150 SuperCrew• F150 SuperCrew with Quad BucketsThe anchors on both sides of the center of the SuperCrew rear seat areprovided only for child seats
The lower anchors for child seatinstallation are located at the rearsection of the seat between thecushion and seat back. The LATCHanchors are below t
Many lights will illuminate when you start your vehicle to make sure thebulb works. If any light remains on after starting the vehicle, have therespec
STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo
When starting a fuel-injected engine, don’t press the accelerator beforeor during starting. Only use the accelerator when you have difficultystarting
If starting a vehicle with an automatic transmission:• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).If starting a vehicle
• Turn the key to 4 (ON) withoutturning the key to 5 (START).12345Driving133
Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced.• If the driver’s safety
Guarding against exhaust fumesCarbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects.If you smell exhaust fumes i
Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake
If the steering wanders or pulls, check for:• an underinflated tire• uneven tire wear• loose or worn suspension components• loose or worn steering com
If you cannot move the gearshift lever out of P (Park) with ignition inthe ON position and the brake pedal depressed:1. Apply the parking brake, turn
This position locks the transmission and prevents the rear wheels fromturning.To put your vehicle in gear:• Start the engine• Depress the brake pedal•
Air bag readiness: If this light failsto illuminate when ignition is turnedto ON, continues to flash or remainson, have the system servicedimmediately
• O/D (Overdrive) is automatically returned each time the key is turnedoff.2 (Second)This position allows for second gear only.• Provides engine braki
Do not rock the vehicle if the engine is not at normal operatingtemperature or damage to the transmission may occur.Do not rock the vehicle for more t
• 4.2L V6 engine (4x2 and 4x4)Upshifts when accelerating (recommended for best fueleconomy)Shift from: Transfer case position (if equipped)2H or 4H 4L
Upshifts when cruising (recommended for best fuel economy)Shift from: Transfer case position (if equipped)2H or 4H 4L1 - 2 16 km/h (10 mph) 6 km/h (4
• All applicationsMaximum downshift speeds1Shift from: Transfer case position (if equipped)2H or 4H 4LD(Overdrive) -489 km/h (55 mph) 34 km/h (21 mph)
FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED)For important information regarding safe operation of this typeof vehicle, see Preparing to drive your v
4L (4WD Low)– Uses extra gearing to provide maximum power to allfour wheels at reduced speeds. Intended only for off-road applicationssuch as deep san
Using the electronic shift 4WD system (if equipped)2H (2WD High) - Power to the rear wheels only; used for street andhighway driving.4H (4WD High) - U
Driving off-road with truck and utility vehicles4WD vehicles are specially equipped for driving on sand, snow, mud andrough terrain and have operating
• It often may be less risky to strike small objects, such as highwayreflectors, with minor damage to your vehicle rather than attempt asudden return
Transmission control indicatorlight (TCIL): Illuminates when theoverdrive function of thetransmission has been turned off,refer to the Driving chapter
turn the steering wheel only as rapidly and as far as required to avoidthe emergency. Excessive steering will result in less vehicle control,not more.
Power is supplied to all four wheelsthrough a transfer case. On 4WDvehicles, the transfer case allowsyou to select 4WD when necessary.Information on t
Once through water, always try the brakes. Wet brakes do not stop thevehicle as effectively as dry brakes. Drying can be improved by movingyour vehicl
When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This r
Avoid sudden braking as well. Although a 4WD vehicle may acceleratebetter than a two-wheel drive vehicle in snow and ice, it won’t stop anyfaster, bec
Tires can be damaged during off-road use. For your safety, tires that aredamaged should not be used for highway driving because they are morelikely to
and adversely affect driver and passenger safety. Frequent inspection ofvehicle chassis components is recommended if the vehicle is subjected toheavy
• Maximum Trailer Weight Rating: Maximum weight of a trailer thevehicle is permitted to tow. The maximum trailer weight rating isdetermined by subtrac
Loaded vehicles may handle differently than unloaded vehicles.Extra precautions, such as slower speeds and increased stoppingdistance, should be taken
Engine Rear axle ratio MaximumGCWR-kg(lbs.)Maximumtrailerweight-kg(lbs.)Regular Cab 4x2 w/automatic transmission4.2L 3.31 4077 (9000) 2132 (4700)4.2L
GAUGESStandard instrument cluster gaugesOptional instrument cluster gaugesHarley—Davidson instrument cluster gaugesMPHkm/h2040608010014012016030400102
Engine Rear axle ratio MaximumGCWR-kg (lbs.)Maximumtrailerweight-kg (lbs.)4.6L 3.55 3538 (7800) 1588 (3500)SuperCab 4x2 w/manual transmission4.2L 3.08
Engine Rear axle ratio Maximum GCWR- kg (lbs.)Maximumtrailer weight -kg (lbs.)Regular Cab 4x4 w/manual transmission4.2L 3.31 3265 (7200) 1179 (2600)4.
Load equalizing hitchWhen hooking up a trailer using a load equalizing hitch, always use thefollowing procedure:1. Park the unloaded vehicle on a leve
Using a step bumper (if equipped)The rear bumper is equipped with an integral hitch and only requires a ballwith a 25.4 mm (one inch) shank diameter.
Launching or retrieving a boatDisconnect the wiring to the trailer before backing the trailerinto the water. Reconnect the wiring to the trailer after
SNOWPLOWINGFord recommends the following specifications for low speed, personaluse snow removal:• F-150 4x4 (except F-150 Supercrew, Lightning and Har
• Federal and most local regulations require additional exterior lampsfor snowplow-equipped vehicles. Consult your dealer for additionalinformation.•
Do not attempt to service, repair, or modify the Air BagSupplemental Restraint System or its fuses. See your Ford orLincoln Mercury dealer.Additional
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
U.S. Ford or Mercury vehicle customers who require roadside assistance,call 1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140.Canadian cus
Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,
This switch is located in the frontpassenger’s footwell, by the kickpanel access cover.To reset the switch:1. Turn the ignition OFF.2. Check the fuel
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey ———3A Violet Vio
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 15A Audio2 5A Powertrain Control Module(PC
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description7 — Not used8 5A Radio, Remote entry module,GEM, In-vehicle entertainmentsy
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description23 10A Trailer tow battery Charge relay,Turn/Hazard flasher, 4x4solenoids,
Always replace the cover to the power distribution box beforereconnecting the battery or refilling fluid reservoirsIf the battery has been disconnecte
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription8 15A* Power door locks, CentralSecurity Module (CSM), Lockrelays (not used on SuperC
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription102 50/20A** Four-wheel Anti-lock BrakeSystem (4WABS)module/Rear-wheel Anti-lockBrake
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription205 — Horn relay206 — Fog lamp relay207 — Front washer pump relay208 — Intercooler pu
The use of tire sealants is not recommended and maycompromise the integrity of your tires. The use of tire sealantsmay also affect your tire pressure
Battery voltage gauge: Indicatesthe battery voltage when theignition is in the ON position. If thepointer moves and stays outside thenormal operating
Removing the spare tire1. If equipped with a two piece lug wrench, assemble the lug wrench asshown in the illustration.• To assemble, screw the partst
1. Park on a level surface, activatehazard flashers and set the parkingbrake.2. Place gearshift lever in P (Park)(automatic transmission) or in therev
When one of the rear wheels is off the ground, the transmissionalone will not prevent the vehicle from moving or slipping off thejack, even if the tra
• RearTo lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engine when yourve
• Seven lug nut wheel12. Stow the flat tire. Refer to Stowing the flat/spare tire.13. Stow the jack and lug wrench. Make sure the jack is fastened so
ratchets or slips with little effort, take the vehicle to your dealer forassistance at your earliest convenience.4. Check that the tire lies flat agai
4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level.5. Tu
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
2. Remove the jumper cable on the negative (-) connection of thebooster vehicle’s battery.3. Remove the jumper cable from the positive (+) terminal of
AM/FM STEREO CASSETTE1. Balance: Press to shift sound tothe left/right speakers.2. Fade: Press to shift sound to therear/front speakers.3. CLK: To set
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeFord Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you
Ford Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf you own a Lincoln vehicle and are away f
In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or
The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedu
from Ford and Lincoln Mercury dealership management, recognized fortheir business leadership qualities.What the Board needsTo have your case reviewed
Making a decisionBoard members review all available information related to eachcomplaint, including oral presentations, and arrive at a fair and impar
settlement have failed. This procedure is without cost to you and isdesigned to eliminate the need for lengthy and expensive legalproceedings.In the C
If you buy your vehicle in North America and then relocate outside ofthe U.S. or Canada, register your vehicle identification number (VIN) andnew addr
2. Four or more repair attempts are made on the same nonconformity (adefect or condition that substantially impairs the use, value or safety ofthe veh
Locks and Security 74Keys 74Locks 74Anti-theft system 76Seating and Safety Restraints 85Seating 85Safety restraints 93Air bags 106Child restraints 114
next selection). Then, press REW (for the beginning of the currentselection) or FF (to advance to the next selection). The tape MUST havea blank secti
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam
• 4.2L V6 engine• 4.6L V8 and 5.4L V8 engineCleaning202
• 5.4L Supercharged V8 engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTIC (NON-P
INSTRUMENT PANEL AND CLUSTER LENSClean the instrument panel with a damp cloth, then dry with a dry cloth.• Avoid cleaners or polish that increase the
For King Ranch F-150 SuperCrew leather seats, refer to separatesection in this chapter.• To clean, use a soft cloth with Motorcraft Deluxe Leather and
CONDITIONINGBottles of King Ranch Leather Conditioner are available at the KingRanch Saddle Shop. Visit the Web site at www.krsaddleshop.com,ortelepho
exceed rigid specifications. For best results, use the following productsor products of equivalent quality:Motorcraft Custom Clearcoat Polish (ZC–8–A)
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
Working with the engine on• Automatic transmission:1. Set the parking brake and shift to P (Park).2. Block the wheels.• Manual transmission:1. Set the
13. AM/FM: Press to choose afrequency band in radio mode.14. Bass: Press/ todecrease/increase the bass output.15. Treble: Press/ todecrease/increase t
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.2L V6 engine1. Battery2. Engine oil filler cap3. Engine oil dipstick4. Clutch fluid reservoir (manua
4.6L V8/5.4L V8 engines1. Power steering fluid reservoir2. Clutch fluid reservoir (manual transmission)3. Engine oil dipstick4. Brake fluid reservoir5
5.4L Supercharged V8 engine1. Engine oil dipstick2. Power steering fluid reservoir3. Brake fluid reservoir4. Power distribution box5. Engine coolant r
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
• 4.2L engine• 4.6L/5.4L engineMaintenance and Specifications214
5. Locate and carefully remove the engine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.
Engine oil and filter recommendationsLook for this certificationtrademark.SAE 5W-20 engine oil is recommended.Only use oils “Certified For Gasoline En
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
1. Bass: Press BASS and the pressSEL to increase/decrease theamount of bass output.Treble: Press TREB and then pressSEL to increase/decrease theamount
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “cold fill level” or within the “c
Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant couldmake it difficult to see through
For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when
Recycled engine coolant• Motorcraft Premium Engine Coolant (green-colored): Forvehicles equipped with this coolant, use only recycled engine coolantpr
• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damag
When fail-safe mode is activatedYou have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be ab
Gasoline may contain benzene, which is a cancer-causing agent.Observe the following guidelines when handling automotive fuel:• Extinguish all smoking
The flow of fuel through a fuel pump nozzle can produce staticelectricity, which can cause a fire if fuel is pumped into anungrounded fuel container.U
If you do not use the proper fuel filler cap, excessive pressure orvacuum in the fuel tank may damage the fuel system or causethe fuel cap to disengag
Fuel qualityIf you are experiencing starting, rough idle or hesitation driveabilityproblems during a cold start, try a different brand of “Regular” un
Setting the clock: Press RDS until SELECT HOUR or SELECT MINS isdisplayed. Use the SEL control to manually increase/decrease (/ )the time.6. AUTO: All
Fuel FilterFor fuel filter replacement, see your dealer or a qualified servicetechnician. Refer to the scheduled maintenance guide for the appropriate
• Always use fuel with the recommended octane rating.• Use a known quality gasoline, preferably a national brand.• Use the same side of the same pump
• Anticipate stopping; slowing down may eliminate the need to stop.• Sudden or hard accelerations may reduce fuel economy.• Slow down gradually.• Driv
• Using fuel blended with alcohol may lower fuel economy.• Fuel economy may decrease with lower temperatures during the first12–16 km (8–10 miles) of
If other than Ford, Motorcraft or Ford-authorized parts are used formaintenance replacements or for service of components affectingemission control, s
Allow the vehicle to sit for at least eight hours without starting theengine. Then, start the engine and complete the above driving cycle. Theengine m
BRAKE FLUID RESERVOIRThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels below the “M
1. Clean the reservoir cap beforeremoval to prevent dirt and waterfrom entering the reservoir.2. Remove cap and rubberdiaphragm from reservoir.3. Add
4. Latch the gearshift lever in P (Park) and leave the engine running.5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. Ifneces
The transmission fluid should be inthis range if at ambient temperature(10°C-35°C [50°F-95°F]).High fluid levelFluid levels above the safe rangemay re
13. Tune: Press to manually moveupor down the frequencyband or to the next/previous CD inthe CD changer (if equipped).14. Scan: Press to hear a briefs
Checking and adding manual transmission fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Fluid leve
Checking and adding transfer case fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough
AIR FILTER MAINTENANCERefer to the scheduled maintenance guide for the appropriate intervalsfor changing the air filter element.When changing the air
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
Tire rotationBecause your vehicle’s tires perform different jobs, they often weardifferently. To make sure your tires wear evenly and last longer, rot
Replacing the tiresReplace the tires when the wearband is visible through the tiretreads. Due to exposure to theelements and exhaust you shouldreplace
The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and ch
2If a spark plug is removed for inspection and replaced, it must bereinstalled in the same cylinder. If a spark plug needs to be replaced, useonly spa
Fluid Ford PartNameApplication CapacityFuel tank N/A 4x4 Reg. Cab withshort wheelbase92.7L (24.5gallons)4x2 Regular Cab,SuperCab andSuperCrew withshor
PREMIUM IN-DASH SIX CD SOUND SYSTEM1. Seek: Press and releaseSEEK/ for previous/nextstrong station, or track of currentdisc.2. Rewind: Press for a slo
Fluid Ford PartNameApplication CapacityRear axle5Motorcraft SAE75W-140Synthetic RearAxle Lubricant10.25 inch axle 3.3L (6.9 pints)7Windshieldwasher fl
axle assembly has been submerged in water. The axle lubricant shouldbe changed any time the rear axle has been submerged in water.6Service refill capa
ItemFord partname orequivalentFord partnumberFordspecificationEngine coolant MotorcraftPremium EngineCoolant(green-colored)VC-4–A (US) orCXC-10(Canada
ItemFord partname orequivalentFord partnumberFordspecificationAutomatictransmission(4R100)2MotorcraftMERCON威 ATFXT-2-QDX MERCON威Automatictransmission(
ENGINE DATAEngine4.2L V6engine4.6L V8engine5.4L V8engine5.4LSuperchargedV8 engineCubic inches 256 281 330 330Requiredfuel87 octane 87 octane 87 octane
DimensionBody StyleRegularCab 4x2Regular Cab4x4Super Cab4x2Super Cab4x4(3) Overallheight1846 mm(72.7 in)(SWB)1838 mm(72.4 in)(LWB)1915 mm(75.4 in)(SWB
1Vehicle width, including mirrors: 2279 mm (89.7 in)25314Maintenance and Specifications256
F-150 SuperCrewDimensionBody StyleSuperCrew 4x2 mm(in)SuperCrew 4x4mm(in)(1) Overall length5738(225.9)5745(226.2)(2) Overall width2009(79.1)12029(79.9
2Harley-Davidson height is 1852 mm (72.9 in)25314Maintenance and Specifications258
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
6. Bass: Press BASS; then pressSEL/ to decrease/increasethe bass output.Treble: Press TREB; then pressSEL/ to decrease/increasethe treble output.7. Se
1. World manufacturer identifier2. Brake type and gross vehicleweight rating (GVWR)3. Vehicle line, series, body type4. Engine type5. Check digit6. Mo
FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincol
Dash trim (wood grain)Engine block heatersManual sliding rear windowPower sliding rear windowRemote start systemTire stepTravel equipmentCargo cage (S
Protection and appearance equipmentBed mat/bedliner tailgate coversBed matsBedlinersBull bar (chrome & black)Cap (hard, color keyed — Leer supplie
Side window air deflectorsTailgate covers, diamond plateTonneau covers (hard, color keyed — Leer supplier branded)Tonneau covers (soft)Truck coverUniv
AAccessory delay ...57Air bag supplemental restraintsystem ...106and child safety seats ..
interior ...204interior trim ...204plastic parts ...203washing ...
dipstick ...213filter, specifications ...216, 247recommendations ...216refill capacities ...
Infant seats(see Safety seats) ...118Inspection/maintenance (I/M)testing ...234Instrument panel
Power distribution box(see Fuses) ...174Power door locks ...74Power point ...
10. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, press andhold a preset button until soundreturns. In CD mode, pres
Transfer casefluid checking ...241Transmissionautomatic operation ...137fluid, checking and adding(automatic) ...
271
272
16. Scan: Press to hear a briefsampling of all listenable stations orCD tracks. Press again to stop.17. Disc/Tune: Radio: Pressor to manually tune dow
Speed sensitive volume(if equipped): Radio volume automatically changes with vehicle speed tocompensate for road and wind noise. Press and hold the vo
Customer Assistance 191Reporting safety defects (U.S. only) 199Cleaning 200Maintenance and Specifications 208Engine compartment 210Engine oil 213Batte
8. Auto: Press to set first six strongstations into AM, FM1 or FM2memory buttons; press again toreturn to normal stations.9. CLK: Press and hold to se
15. Side 1–2: Press to play reverseside of the tape.16. Fast Forward (FF): Press tofast forward the tape.17. Rewind (REW): Press torewind the tape.18.
22. AM/FM: Press to select AM/FMfrequency band.REAR AUDIO CONTROLS (IF EQUIPPED)The rear seat controls allow the rear seat passengers to operate thera
RADIO FREQUENCIESAM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsComm
CD/CD PLAYER CAREDo:• Handle discs by their edges only. Never touch the playing surface.• Inspect discs before playing. Clean only with an approved CD
HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe
4. Direct the outer instrument panel vents towards the side windowsTo increase airflow to the outer instrument panel vents, close the ventslocated in
OPERATING TIPS• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (EATC)SYSTEM1. OFF: Press to turn the systemOFF.2. AUTOMATIC: Press to engageautomatic mode. The system willd
4. Defrost: Distributes outside air through the windshield defrostervents.5. Floor/defrost: Distributes outside air through the windshielddefroster an
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
OPERATING TIPS• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola
Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the ON position and• the h
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parklamp operatio
INTERIOR LAMPSMap lampsTo turn on the map lamps, press thecontrol next to each lamp.If equipped with a moon roof, pressthe control next to the map lam
Courtesy/reading lampsThe dome lamp lights when thecontrol is in the DOOR (left)position, any door is open, theinstrument panel switch is pushedpast t
Function Number ofbulbsTrade numberHeadlamps 2 9007Front park/turn lamps 2 3157AK (amber)Foglamps 2 91451Backup lamp 2 3156KRear stop/turn/sidemarker/
4. Remove bulb retainer ring byturning it counterclockwise, thenslide the ring off the plastic base.5. Carefully pull bulb assembly outof headlamp ass
3. Remove bulb socket from theparking lamp assembly by turning itcounterclockwise.4. Pull bulb straight out of socketand press in the new bulb.Install
Replacing high-mount brake and cargo lamp bulbsMake sure the headlamp control isin the OFF position.1. Remove the two screws and movethe lamp assembly
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury and prevent possibledamage to others, you
Replacing license plate lamp bulbsThe license plate bulbs are locatedbehind the rear bumper. To changethe license plate lamp bulbs:1. Reach behind the
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT STEERING WHEEL (IF EQUIPPED)To adjust the steering wheel:1. Pull and hold the steering wheelrelease control toward you.2. Move the steering wheel
Installing a garage door opener (if equipped)The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers:1. Pl
If the outside temperature falls below 3°C (38°F), the display willalternate from “ICE” to the outside temperature at a two second rate forone minute.
Compass calibration adjustmentPerform this adjustment in an openarea free from steel structures andhigh voltage lines:• Press and hold the SELECTcontr
Auxiliary power point (SuperCrew only)An additional auxiliary power pointis located on the right side rear trimpanel next to the rear seat.CENTER CONS
A driver’s first responsibility is the safe operation of the vehicle.The most important thing you can do to prevent a crash is toavoid distractions an
Power rear slider window (if equipped)• Press and hold the open arrowside of control to open window.• Press and hold the closed arrowside of control t
Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog. The mirrors are activatedwhen the vehicle is runn
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
Never adjust the accelerator and brake pedal with feet on thepedals while the vehicle is moving.SPEED CONTROL (IF EQUIPPED)With speed control set, you
Resuming a set speedPress the RES/RSM (resume)control and release it. This willautomatically return the vehicle tothe previously set speed. TheRES/RSM
• Depress the brake pedal until thedesired vehicle speed is reached,press the SET ACCEL control.Turning off speed controlThere are two ways to turn of
• To tilt into the vent position (when the glass panel is closed), pressand hold the front portion of the moon roof control. To close from thevent pos
ProgrammingDo not program the HomeLink威 Universal Transceiver with thevehicle parked in the garage.Note: Your vehicle may require the ignition switch
6. At the garage door opener receiver (motor-head unit) in the garage,locate the “learn” or “smart” button (usually near where the hangingantenna wire
HomeLink威 is now in the train (or learning) mode and can beprogrammed at any time beginning with step 2 in the “Programming”section.Reprogramming a si
Operating TravelNote姞TravelNote威 records and stores messages for up to three minutes in totallength with simple controls. When you get an idea or reme
To delete a message:1. Press and release the DEL buttonwhile listening to a message orshortly after. The indicator light willflash green twice.2. To d
TAILGATE REMOVALYour tailgate is removable to allowmore room for loading.1. Lower the tailgate.2. Use a screwdriver to pry thespring clip (on each con
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Air bag in the Seating
To stow the bed extender, follow steps one through four in reverse order.The bed extender may be used to secure a load of up to 46 kg (100 lbs.)on the
2. Pull the rear corner assist loopsof the cover, outward, then upwardto release the tension. Lift up on therear edge of the cover to remove itfrom th
Flareside only:• Remove two cross bars from pickup box by pushing towards eitherside to release tension.• Lower tailgate, depress the levers on each s
For installation of the cover, follow the removal procedure in reverseorder.Make sure the crossbows are locked in the notches in the side rails andthe
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
INTERIOR TONNEAU COVER RELEASE (IF EQUIPPED)Your vehicle is equipped with a mechanical interior tonneau coverrelease handle that provides a means of e
Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment.Your ve
Power door unlock disable feature (if equipped)The UNLOCKfeature on your power door locks will not work frominside the vehicle when:• the ignition has
To replace the battery:1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE FRONT PART OFTHE RE
6. Within 20 seconds press any button on the remote entry transmitter.Note: If more than 20 seconds have passed you will need to start theprocedure ov
F150 SuperCrew, F150 5.4L Supercharged “Lightning” andHarley-Davidson F-150 Owners: SnowplowingYour vehicle is not recommended for snowplowing. Ford m
To deactivate/reactivate the autolock feature using the keypadYour vehicle comes with the autolock feature activated. Todeactivate/reactivate this fea
Tips:• Do not set a code that uses five of the same number.• Do not use five numbers in sequential order.• The factory set code will work even if you
SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEMSecuriLock娂 passive anti-theft system is an engine immobilizationsystem. This system is designed to prevent the e
Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 3(OFF) position.TheTHEFTindicator will flashevery two seconds when
1. Insert a previously programmedcoded key into the ignition.2. Turn the ignition from the 1 (OFF) position to the 3 (ON) position.Keep the ignition i
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Full bench seat (if equipped)• Lift the release bar to move theseat forward or backward. Ensurethat the seat is relatched intoplace.• Pull up on the l
Captain’s chair (if equipped)• Lift the track release bar to movethe seat forward or rearward.Make sure that the seat isrelatched into place.• Pull th
Press to raise or lower the frontportion of the seat cushion.• Type A• Type BPress to raise or lower the rearportion of the seat cushion.• Type A• Typ
Press the control to move the seatforward, backward, up or down.• Type A• Type BHeated seats (if equipped)To operate the heated seats:• Push control l
Notice to owners of F150 5.4L Supercharged “Lightning” vehiclesBefore you drive your vehicle, be sure to read the “SVT Lightning TruckOwner’s Guide Su
Returning the seat to seating positionAlways be sure that the seat is in a latched position, whether theseat is occupied or empty. If not latched, the
3. Pull seatback toward front seatand down into load floor position.4. Make sure seat is pushed all theway down and locks into position.Returning the
2. Lift seatback up until it locks intovertical position.3. Return the head restraint to its original position.If the head restraint is insertedbackwa
SAFETY RESTRAINTSSafety restraints precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce
Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Checkseat covers and buckle
• Front seats• Rear seats (if equipped)The front and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front p
Automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt
2. Grasp the shoulder portion andpull downward until the entire beltis extracted.3. Allow the belt to retract. As the belt retracts, you will hear a c
The Seat Integrated Restraints (SIR) seat (which has shoulder beltsattached to the corners of the front seat back) is equipped with a bucklepretension
• 4–door SuperCab (Bench seatsonly)To lower the shoulder belt height, push the button and slide the heightadjuster down. To raise the height of the sh
Commentaires sur ces manuels