Introduction 3Instrument Cluster 10Warning and control lights 10Gauges 14Entertainment Systems 18AM/FM stereo with CD 18Climate Controls 32Manual heat
WARNING LIGHTS AND CHIMESBase instrument clusterOptional instrument clusterMach 1 instrument clusterWarning lights and gauges can alert you to a vehic
• Turn the key to 4(ON) withoutturning the key to 5(START).Make sure the corresponding lights illuminate orilluminate briefly. If a light fails to ill
Starting the engine1. Turn the key to 4(ON) without turningthe key to 5 (START).2. Turn the key to 5(START), then releasethe key as soon as theengine
Important ventilating informationIf the engine is idling while the vehicle is stoppedfor a long period of time, open the windows at least2.5 cm (one i
Using ABSWhen hard braking is required, apply continuousforce on the brake pedal; do not pump the brakepedal since this will reduce the effectiveness
Always set the parking brake fully and makesure that the gearshift is securely latched inP (Park) (automatic transmission) or in 1 (First)(manual tran
engine will not “rev-up” when you push further onthe accelerator. This is normal system behavior andshould be no reason for concern.The Traction Contr
Extended use of other than the manufacturer’sspecified size tires on a Traction-Lok rear axle couldresult in a permanent reduction in effectiveness.Th
Always set the parking brake fully and makesure the gearshift is latched in P (Park).Turn the ignition to the LOCK position and removethe key whenever
To put your vehicle in gear, start the engine, depressthe brake pedal, then move gearshift lever out of P(Park). Once you place the gearshift lever se
Always set the parking brake fully and makesure the gearshift is latched in P (Park).Turn the ignition to the LOCK position and removethe key whenever
Service engine soon:The Service enginesoon indicator lightilluminates when theignition is first turned to the ON position to checkthe bulb. Solid illu
2 (Second)This position allows for second gear only.• Provides engine braking.• Use to start-up on slippery roads.• To return to D (Overdrive), move t
MANUAL TRANSMISSION OPERATION(IF EQUIPPED)Using the clutchThe manual transmission has a starter interlock thatprevents cranking the engine unless the
Upshift according to the following chart:Upshifts when accelerating (recommended for bestfuel economy)Shift from:1 - 2 18 km/h (11 mph)2 - 3 31 km/h (
DRIVING THROUGH WATERDo not drive quickly through standing water,especially if the depth is unknown. Traction or brakecapability may be limited and if
• GVWR (Gross Vehicle Weight Rating):Maximum permissible total weight of the basevehicle, occupants, optional equipment and cargo.The GVWR is specific
Do not use replacement tires with lower loadcarrying capacities than the originals because theymay lower the vehicle’s GVWR and GAWRlimitations. Repla
TRAILER TOWINGYour vehicle is not equipped to tow. No towingpackages are available through Ford orLincoln/Mercury dealers.RECREATIONAL TOWING (ALL WHE
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicleconcern, Ford Motor Company offers acomplimentary roadside assistance program.
USING ROADSIDE ASSISTANCEComplete the roadside assistance identification cardand place it in your wallet for quick reference. In theUnited States, thi
HAZARD FLASHERThe hazard flasher islocated on the steeringcolumn, just behind thesteering wheel. Thehazard flashers willoperate when theignition is in
brake indicates low brake fluid level and the brakesystem should be inspected immediately by yourservicing dealership.Driving a vehicle with the brake
FUSES AND RELAYSFusesIf electricalcomponents in thevehicle are notworking, a fuse mayhave blown. Blownfuses are identified by a broken wire within the
To remove a fuse use the fuse puller tool providedon the fuse panel cover.The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPassenger Com
Fuse/RelayLocationFuse AmpRatingPassenger CompartmentFuse Panel Description15 15A Power lumbar16 — Not used17 15A Speed control servo, Shiftlock actua
Fuse/RelayLocationFuse AmpRatingPassenger CompartmentFuse Panel Description36 15A Air bag control module37 5A Adjustable illumination38 20A High beams
The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescriptionRelay 1 — Fog lamp interruptRelay 2 — Int
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription23 — Not used24 20A* A/C pressure25 — Not used26 30A** PCM27 20A** Daytime Running La
When driving with the temporary spare tire do not:• use more than one temporary spare tire at a time• exceed 80 km/h (50 mph) or drive further than3,2
To prevent the vehicle from moving whenyou change a tire, be sure the parking brakeis set, then block (in both directions) the wheelthat is diagonally
2. Remove the sparetire, jack and lugwrench.3. Remove the centerornament (if equipped)from the wheel. Looseneach wheel lug nutone-half turncountercloc
To lessen the risk of personal injury, do notput any part of your body under the vehiclewhile changing a tire. Do not start the enginewhen your vehicl
Overdrive off:Illuminates when theoverdrive function ofthe transmission has been turned off, refer to theDriving chapter. If the light flashes steadil
To remove theanti-theft lug nut:1. Insert the key overthe locking lug nut.Make sure you hold the key square to the lug nut. Ifyou hold the key at an a
Preparing your vehicleWhen the battery is disconnected or a new battery isinstalled, the transmission must relearn its shiftstrategy. As a result, the
2. Connect the other end of the positive (+) cable tothe positive (+) terminal of the assisting battery.3. Connect the negative (-) cable to the negat
Do not connect the end of the second cableto the negative (-) terminal of the battery tobe jumped. A spark may cause an explosion of thegases that sur
2. Remove the jumper cable on the negative (-)connection of the booster vehicle’s battery.3. Remove the jumper cable from the positive (+)terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact aprofessional towing service or, if you are a memberof a roadside assistance program, yo
GETTING THE SERVICES YOU NEEDAt homeFord Motor Company and Ford of Canada haveauthorized dealerships to service your vehicle. It ispreferred that you
P.O. Box 6248Dearborn, Michigan 481211-800-392-3673 (FORD)(TDD for the hearing impaired: 1-800-232-5952)www.ford.comIn Canada:Customer Relationship Ce
• The year and make of your vehicle• The date of vehicle purchase• The current odometer reading• The vehicle identification number (VIN)If you still h
time, distance and deductible combinations whichcan be tailored to fit your own driving needs. FordESP also offers reimbursement benefits for towingan
GAUGESBase instrument cluster gaugesOptional instrument cluster gaugesMach 1 instrument cluster gaugesP!BRAKELCEFHLH1020302040608010012014016018040506
• sales disputes between customer and dealerexcept those associated with warranty repairs orconcerns with the vehicle’s performance asdesigned• a requ
address provided on the application form. Somestates will require you to use certified mail, withreturn receipt requested.Your application is reviewed
it is your right to make an oral presentation beforethe Board, this is not a requirement and the Boardwill decide the case whether or not an oralprese
UTILIZING THE MEDIATION/ARBITRATIONPROGRAM (CANADA ONLY)In those cases where you continue to feel that theefforts by Ford and the dealer to resolve af
The use of leaded fuel in your vehicle withoutproper conversion may damage the effectiveness ofyour emission control system and may cause engineknocki
Or call:For a free publication catalog, order toll free:1-800-782-4356Monday-Friday 8:00 a.m. - 6:00 p.m. ESTHelm, Incorporated can also be reached by
2. Four or more repair attempts are made on thesame nonconformity (a defect or condition thatsubstantially impairs the use, value or safety of thevehi
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarmwater and a neutral Ph shampoo, such as MotorcraftDetail Wash (ZC-3–A), which is
• Do not allow paint sealant to come in contact withany non-body (low-gloss black) colored trim, suchas grained door handles, roof racks, bumpers, sid
ENGINEEngines are more efficient when they are cleanbecause grease and dirt buildup keep the enginewarmer than normal. When washing:• Take care when u
Speedometer: Indicates the current vehicle speed.• Base instrumentcluster• Optional instrumentcluster• Mach 1 instrumentclusterEngine coolanttemperatu
• 4.6L SOHC V8 engine• 4.6L 4V engine (Mach I)• Never wash or rinse the engine while it isrunning; water in the running engine may causeinternal damag
• If tar or grease spots are present, use Ford ExtraStrength Tar and Road Oil Removal(B7A-19520–AA).WINDOWS AND WIPER BLADESThe windshield, rear windo
INSTRUMENT PANEL AND CLUSTER LENSClean the instrument panel with a damp cloth, thendry with a dry cloth.• Avoid cleaners or polish that increase the g
LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protectivecoating over the leather.• To clean, use a soft cloth with Motorcraft
Motorcraft Vinyl Cleaner (Canada only) (CXC-93)Motorcraft Vinyl Conditioner (Canada only)(CXC-94)Motorcraft Deluxe Leather and Vinyl Cleaner (notavail
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the enginecompartment for easy location.• We provide a
Working with the engine on• Automatic transmission:1. Set the parking brake and shift to P (Park).2. Block the wheels.• Manual transmission:1. Set the
3. Lift the hood and secure it with the prop rod.IDENTIFYING COMPONENTS IN THE ENGINECOMPARTMENT3.8L OHV V6 engine1. Engine oil filler cap2. Engine oi
4. Power distribution box5. Windshield washer fluid reservoir6. Battery7. Power steering fluid reservoir8. Engine coolant reservoir9. Air filter assem
4.6L 4V V8 (Mach 1) engine1. Engine oil filler cap2. Brake fluid reservoir3. Engine oil dipstick4. Power distribution box5. Windshield washer fluid re
Odometer: Registersthe total kilometers(miles) of the vehicle.Trip odometer:Registers thekilometers (miles) ofindividual journeys.Press and release th
WINDSHIELD WASHER FLUIDAdd fluid to fill thereservoir if the level islow. In very coldweather, do not fill thereservoir completely.Only use a washer f
4. Open the hood. Protect yourself from engine heat.5. Locate and carefully remove the engine oil levelindicator (dipstick).• 3.8L V6 engine• 4.6L SOH
•If the oil level is between the MIN—MAX marks,the oil level is acceptable. DO NOT ADD OIL.• If the oil level is below the MIN mark, add enoughoil to
Adding engine oil1. Check the engine oil. For instructions, refer toChecking the engine oil in this chapter.2. If the engine oil level is not within t
Do not use supplemental engine oil additives, oiltreatments or engine treatments. They areunnecessary and could, under certain conditions,lead to engi
If your battery has a cover/shield, make sure itis reinstalled after the battery has beencleaned or replaced.For longer, trouble-free operation, keep
Because your vehicle’s engine is electronicallycontrolled by a computer, some control conditionsare maintained by power from the battery. When thebatt
• Always dispose ofautomotive batteriesin a responsiblemanner. Follow yourlocal authorizedstandards fordisposal. Call yourlocal authorizedrecycling ce
• 3.8L OHV V6 engine• 4.6L SOHC V8 / 4.6L4v V8 (Mach 1)enginesWhen the engine is cold, check the level of theengine coolant in the reservoir.• The eng
Adding engine coolantWhen adding coolant, make sure it is a 50/50mixture of engine coolant and distilled water. Addthe mixture to the coolant reservoi
Battery voltagegauge: Indicates thebattery voltage whenthe ignition is in theON position. If the pointer moves and stays outsidethe normal operating r
• Do not add/mix an orange-colored, extendedlife coolant such as Motorcraft SpecialityOrange Engine Coolant, VC-2 (US) orCXC-209 (Canada), meeting For
2. When the engine is cool, wrap a thick clotharound the cap. Slowly turn cap counterclockwiseuntil pressure begins to release.3. Step back while the
11. Wrap a thick cloth around the radiator cap andcautiously remove the radiator cap.12. Add a 50/50 mixture of engine coolant anddistilled water to t
9. Check the coolant level in the reservoir beforeyou drive your vehicle the next few times (with theengine cool).10. If necessary, add a 50/50 mixtur
Fill your engine coolant reservoir as outlined inAdding engine coolant in this chapter.Severe climatesIf you drive in extremely cold climates (less th
WHAT YOU SHOULD KNOW ABOUTAUTOMOTIVE FUELSImportant safety precautionsDo not overfill the fuel tank. The pressure inan overfilled tank may cause leaka
injury. If fuel is swallowed, call a physicianimmediately, even if no symptoms are immediatelyapparent. The toxic effects of fuel may not bevisible fo
Use the following guidelines to avoid static build-upwhen filling an ungrounded fuel container:• Place approved fuel container on the ground.• DO NOT
The fuel system may be under pressure. Ifthe fuel filler cap is venting vapor or if youhear a hissing sound, wait until it stops beforecompletely remo
Mach 1Your vehicle isdesigned to use“Premium” unleadedgasoline with an(R+M)/2 octane rating of 91 or higher for optimumperformance. The use of gasolin
AM/FM STEREO / SINGLE CD RADIO1. Balance:Press/ to shiftsound to the left/rightspeakers.2. Fade: Press/to shift sound to thefront/rear speakers.3. SCN
Many of the world’sautomakers issued theWorld-wide FuelCharter thatrecommends gasolinespecifications to provideimproved performanceand emission contro
ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fueleconomy is you, the driver. You must gatherinforma
• Always use fuel with the recommended octanerating.• Use a known quality gasoline, preferably anational brand.• Use the same side of the same pump an
Habits• Smooth, moderate operation can yield up to 10%savings in fuel.• Steady speeds without stopping will usually givethe best fuel economy.• Idling
• Perform all regularly scheduled maintenanceitems. Follow the recommended maintenanceschedule and owner maintenance checks found inyour vehicle sched
EMISSION CONTROL SYSTEMYour vehicle is equipped with various emissioncontrol components and a catalytic converter whichwill enable your vehicle to com
Do not make any unauthorized changes to yourvehicle or engine. By law, vehicle owners and anyonewho manufactures, repairs, services, sells, leases,tra
If the Check Engine/Service Engine Soon lightremains on, have your vehicle serviced at the firstavailable opportunity.Readiness for Inspection/Mainten
CHECKING AND ADDING POWER STEERINGFLUIDCheck the power steering fluid. Refer to thescheduled maintenance guide for the service intervalschedules. If a
If your vehicle isequipped with a 4.6LV8 engine, check thepower steering fluidlevel with the engine atambient temperature.Allow at least one-halfhour
6. COMP(Compression): In CDmode, press to bringlouder and softer levels into more comfortablelistening level. The compression icon (c) will appearin t
CLUTCH ADJUSTMENT (IF EQUIPPED)Check the clutchadjustment. Refer tothe scheduledmaintenance guide forthe service intervalschedules.The clutch on yourv
3. With the parking brake engaged and your foot onthe brake pedal, start the engine and move thegearshift lever through all of the gear ranges. Allows
The transmission fluidshould be in this rangeif at ambienttemperature (10°C-35°C[50°F-95°F]).High fluid levelFluid levels above thesafe range may resu
Checking and adding manual transmission fluid(if equipped)1. Clean the filler plug.2. Remove the fillerplug and inspect thefluid level.3. Note: There
Use only fluid that meets Ford specifications. Referto Lubricant Specifications in this chapter.INFORMATION ABOUT UNIFORM TIRE QUALITYGRADINGNew vehic
Traction AA A B CThe traction grades, from highest to lowest are AA,A, B, and C. The grades represent the tire’s ability tostop on wet pavement as mea
• Check the tire pressure when tires are cold, afterthe vehicle has been parked for at least one houror has been driven less than 5 km (3 miles).• Adj
• 17 inch four tirerotationReplacing the tiresReplace the tires whenthe wear band is visiblethrough the tire treads.When replacing full size tires, ne
Failure to follow these precautions mayadversely affect the handling of the vehicle,and increase the risk of loss of vehicle control,vehicle rollover
• The suspension insulation and bumpers will helpprevent vehicle damage. Do not remove thesecomponents from your vehicle when using snowtires and chai
Traction control 104Transmission operation 106Vehicle loading 113Trailer towing 116Roadside Emergencies 117Getting roadside assistance 117Hazard flash
14. CD: Press to enterCD mode or to play aCD already loaded intothe system.15. AM/FM: Press tochoose a frequencyband in radio mode.16. Bass:Press/ toi
Fluid Ford PartNameApplication CapacityEnginecoolant1MotorcraftPremiumEngine Coolant(green-colored)or MotorcraftPremium GoldEngine Coolant(yellow-colo
Fluid Ford PartNameApplication CapacityTransmissionfluid3MotorcraftMERCON威VATFAutomaticwith 3.8LOHV V6engine13.1L (13.9quarts)4Automaticwith 4.6LSOHCV
scheduled maintenance guide to determine thecorrect service interval.4Indicates only approximate dry-fill capacity. Someapplications may vary based on
Item Ford partnameFord partnumberFordspecificationPowersteeringfluid andconvertibletop fluid (ifequipped)MotorcraftMERCON威 ATFXT-2-QM MERCON威Rear Axle
scheduled maintenance guide to determine thecorrect service interval.ENGINE DATAEngine 3.8L OHVV6 engine4.6L SOHCV8 engine4.6L 4v V8engine(Mach 1)Cubi
VEHICLE DIMENSIONSVehicledimensionsCoupe mm (in) Convertible mm(in)(1) Overall length 4653.3 (183.2) 4653.3 (183.2)(2) Overall width 1856.7 (73.1) 185
IDENTIFYING YOUR VEHICLECertification labelThe National HighwayTraffic SafetyAdministrationRegulations requirethat a Certificationlabel be affixed to
FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of genuine Ford accessories areavailable for your vehicle through your localauthorized Ford, Lincoln
Dash trim, brushed aluminum-lookElectrochromic mirror with compassElectrochromic mirror with compass andtemperature displayEngine block heatersRemote
Side window deflectorSpoilerStyled hood deflectorTonneau cover (mini, for convertible top)Universal floor matsWheels (chrome and painted)For maximum v
3. Scan: Press to heara brief sampling of alllistenable radiostations, CD or MP3 tracks. Press again to stop.4. CLK: To set theclock press and holdthe
AAir bag supplementalrestraint system ... 78and child safetyseats ... 80description ... 78disposal ...
Child safety seats ... 87attaching with tetherstraps ... 91in front seat ... 89in rear seat ... 89Cleaning
EEmergencies, roadsidejump-starting ... 130Emission controlsystem ... 185Engine ... 204–205cleaning ...
driving with a heavyload ... 113location ... 113HHead restraints ... 63Headlamps ... 34aiming
Lug nuts,anti-theft ... 129Lumbar support,seats ... 64MManualtransmission ... 111fluid capacities ...
Safety seats forchildren ... 87Seat belts (see Safetyrestraints) ... 67Seats ... 63child safe
Windowspower ... 44Windshield washer fluidand wipers ... 42checking and addingfluid ... 160repl
10. CD (Rewind):Press and hold untilthe desired selectionpoint is reached. This function is not enabled in MP3mode.11. MP3 directory:Allows you to lis
17. Power/volume:Press to turn ON/OFF;turn to increase ordecrease volume levels.18. CD: Press CD toplay a CD or MP3 disc.When the MP3 disc isloaded, C
Your MACH威 MP3 player is also equipped with ananti-shock buffer for MP3 discs.MP3 FILE DIRECTORY STRUCTUREThe MACH威 MP3 music system recognizes MP3 di
MACH姞 460 SOUND SYSTEM RADIO (CDCHANGER COMPATIBLE)MACH姞 1000 SOUND SYSTEM RADIO (CDCHANGER COMPATIBLE)Your vehicle may be equipped with the MACH1000威
1. Seek: Press andrelease SEEK/for previous/nextstrong station, selection or track.2. Rewind: In CDmode, press untildesired selection isreached.Fast f
5. Eject: Press EJ andchoose thecorresponding preset(1–6) to eject the desired CD. Press and hold toeject all loaded discs.6. Bass: Press BASS;then pr
Show TYPE: Displays the station’s call letters andformat.Compression: Brings soft and loud CD passagestogether for a more consistent listening level.1
14. Load: Press LOADand the correspondingpreset (1–6) to load aCD into the desired slot. Press and hold to load upto six discs at once.15. Shuffle: Pr
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of itsconstituents, and certain vehiclecomponents contain or emit chemicals known tothe
RADIO RECEPTION FACTORSThere are three factors that can effect radioreception:• Distance/strength: The further you travel from anFM station, the weake
CD units are designed to play commerciallypressed 12 cm (4.75 in) audio compact discsonly. Due to technical incompatibility, certainrecordable and re-
MANUAL HEATING AND AIR CONDITIONINGSYSTEM1. Fan speedadjustment: Controlsthe volume of aircirculated in thevehicle.2. Temperature selection: Controls
OPERATING TIPS• To reduce fog build up on the windshield duringhumid weather, place the air flow selector intheposition.• To reduce humidity build up
HEADLAMP CONTROL• The first positionturns on the parking,tail, license plate andside marker lamps.• The outer positionturns on theheadlamps.Foglamp co
High beamsPush the lever towardthe instrument panel toactivate. Pull the levertowards you todeactivate.Flash to passPull toward you slightlyto activat
• (2) Center height of lamp to ground• (3) Twenty five feet• (4) Horizontalreference line2. Measure the heightfrom the center of yourheadlamp to thegr
TURN SIGNAL CONTROL• Push down toactivate the left turnsignal.• Push up to activatethe right turn signal.INTERIOR LAMPSMap lamps (if equipped)If equip
Using the right bulbsReplacement bulbs are specified in the chart below.Headlamp bulbs must be marked with an authorized“D.O.T.” for North America and
Replacing headlamp bulbsTo remove the headlamp bulb:1. Make sure headlamp switch is in the OFFposition, then open the hood.2. At the back of theheadla
Fuel pump shut-off switch In the event ofan accident the safety switch willautomatically cut off the fuel supply to the engine.The switch can also be
Replacing front parking lamp/turn signal bulbs1. Make sure the headlamp control is in the OFFposition and open the hood.2. At the back of theheadlamp,
Replacing foglamp bulbs1. Make sure theheadlamp switch is inthe OFF position.2. Rotate the foglampbulb socketcounterclockwise andremove from foglamp.3
MULTI-FUNCTION LEVERWindshield wiper:Rotate the end of thecontrol away from youto increase the intervalspeed of the wipers;rotate towards you todecrea
TILT STEERING WHEEL (IF EQUIPPED)To adjust the steeringwheel:1. Pull and hold thesteering wheel releasecontrol toward you.2. Move the steeringwheel up
AUXILIARY POWER POINTThe power point is anadditional powersource for electricalaccessories.Power outlets aredesigned foraccessory plugs only.Do not ha
POWER SIDE VIEW MIRRORS(IF EQUIPPED)To adjust your mirrors:1. Move the mirrorselector control all theway to the left toadjust the left mirroror all th
3. Press the SETACCEL control andrelease it.4. Take your foot offthe accelerator pedal.Note:• Vehicle speed may vary momentarily when drivingup and do
increase the vehicle set speed in small amountsby 1.6 km/h (1 mph).• Use the accelerator pedal to get to the desiredspeed. When the vehicle reaches th
CENTER CONSOLEYour vehicle may be equipped with a variety ofconsole features. These include:• Dual cupholders• Auxiliary power point• Coin holder slot
POSITIVE RETENTION FLOOR MAT(IF EQUIPPED)Position the floor mat sothat the eyelet is over thepointed end of theretention post and rotateforward to loc
BREAKING-IN YOUR VEHICLEYour vehicle does not need an extensive break-in.Try not to drive continuously at the same speed forthe first 1,600 km (1,000
4. Close the windshield header clamps immediatelyafter disengagement, to avoid cutting the topmaterial and to permit installation of the vinyl boot.5.
3. Insert boot tongueinto groove located onrear of seat.4. To remove, unfastenthe snaps or pivotlatches and the boottongue.5. Pull forward and liftoff
5. Open both top clamps before the top meets thewindshield header6. Continue to use the top motor to raise the topuntil it has reached the fully close
KEYSThe key operates all locks on your vehicle. In case ofloss, replacement keys are available from yourdealer.You should always carry a second key wi
To open the luggagecompartment door (lid)from within theluggage compartment,pull the illuminated “T”shaped handle andpush up on the trunklid. The hand
On hot days, the temperature in the trunkor vehicle interior can rise very quickly.Exposure of people or animals to these hightemperatures for even a
2. Press and release again within three secondsto unlock the passenger door.Locking the doors1. Press and release to lock all the doors. Note:the inte
• nearby radio towers,• structures around the vehicle and• other vehicles parked next to the vehicle.To replace the battery:1. Twist a thin coinbetwee
To reprogram theremote entrytransmitters:1. Ensure the vehicle iselectronically unlocked.2. Put the key in theignition.3. Turn the key from the 2 (LOC
• the remote transmitter lock control is pressed, or• after 25 seconds of illumination.The dome lamp control (if equipped) must not beset to the OFF p
Data RecordingComputers in your vehicle are capable of recordingdetailed data potentially including but not limited toinformation such as:• the use of
Note: Large metallic objects, electronic devices thatare used to purchase gasoline or similar items, or asecond coded key on the same key chain may ca
Automatic disarmingSwitching the ignition to the 4 (ON) position with acoded key disarms the vehicle.• TheTHEFTindicator will illuminate for threeseco
1. Insert a previouslyprogrammed coded keyinto the ignition.2. Turn the ignitionfrom the 3 (OFF)position to the 4 (ON)position. Keep theignition in th
SEATINGNotes:Reclining the seatback can cause anoccupant to slide under the seat’s safetybelt, resulting in severe personal injuries in theevent of a
Always drive and ride with your seatbackupright and the lap belt snug and low acrossthe hips.Lift handle to moveseat forward orbackward.Pull lever up
Always drive and ride with your seatbackupright and the lap belt snug and low acrossthe hips.Reclining the seatback can cause anoccupant to slide unde
REAR SEATSUse the seatbackrelease to fold the backof the front seatforward for rear seatpassenger entry or exit.This release handle islocated on the l
SAFETY RESTRAINTSSafety restraints precautionsAlways drive and ride with your seatbackupright and the lap belt snug and low acrossthe hips.To reduce t
Each seating position in your vehicle has aspecific safety belt assembly which is madeup of one buckle and one tongue that are designedto be used as a
2. To unfasten, pushthe release button andremove the tonguefrom the buckle.The front and rear outboard safety restraints in thevehicle are combination
Notice to owners of Cobra vehiclesBefore you drive your vehicle, be sure to read the“SVT Cobra Owner’s Guide Supplement.” This bookcontains important
Failure to replace the Belt and Retractorassembly could increase the risk of injury incollisions.Vehicle sensitive modeThis is the normal retractor mo
How to use the automatic locking mode• Buckle thecombination lap andshoulder belt.• Grasp the shoulderportion and pulldownward until theentire belt is
Disconnect the combination lap/shoulder belt andallow it to retract completely to disengage theautomatic locking mode and activate the vehiclesensitiv
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war
The following are reasons most often given for notwearing safety belts: (All statistics based on U.S.data)Reasons given... Consider...“Crashes are rar
Reasons given... Consider...“I have an air bag” Air bags offer greater protectionwhen used with safety belts.Frontal airbags are not designedto inflat
• The parklamps/headlamps are in OFF position (Ifvehicle is equipped with Autolamps, this will notaffect the procedure).To reduce the risk of injury,
• Followed by three seconds with the safety beltwarning light off.• Once again, the safety belt warning light will flashfour times per second for thre
replaced. Safety belt assemblies not in use during acollision should also be inspected and replaced ifeither damage or improper operation is noted.Fai
Always transport children 12 years old andunder in the back seat and always properlyuse appropriate child restraints.The National Highway Traffic Safe
These are some of the symbols you may see on yourvehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-S
Children and air bagsChildren must alwaysbe properly restrained.Accident statisticssuggest that childrenare safer whenproperly restrained inthe rear s
The air bags inflate anddeflate rapidly uponactivation. After air bagdeployment, it isnormal to notice asmoke-like, powderyresidue or smell theburnt p
Several air bag system components get hotafter inflation. Do not touch them afterinflation.If the air bag has deployed, the air bag willnot function a
SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how toproperly use safety restraints for children. Also seeAir bag suppleme
If the shoulder belt portion of a combination lap andshoulder belt can be positioned so it does not crossor rest in front of the child’s face or neck,
• Can the child sit allthe way back againstthe vehicle seat backwith knees bentcomfortably at theedge of the seatwithout slouching?• Does the lap belt
Both can be used in any vehicle in a seating positionequipped with lap/shoulder belts if your child is over40 lbs.The shoulder belt should cross the c
SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the sizeand weight of the child. Carefully fo
• Use the correct safety belt buckle for that seatingposition (the buckle closest to the direction thetongue is coming from).• Insert the belt tongue
Installing child safety seats with combinationlap and shoulder beltsIf you must use aforward facing childseat in the front seat(reminder - children 12
Vehicle Symbol GlossaryChild Safety DoorLock/UnlockInterior LuggageCompartmentRelease SymbolPanic Alarm Engine OilEngine CoolantEngine CoolantTemperat
2. Pull down on theshoulder belt and thengrasp the shoulder beltand lap belt together.3. While holding theshoulder and lap beltportions together, rout
6. Allow the belt to retract. The belt will click as itretracts to indicate it is in the automatic lockingmode.7. Pull the lap beltportion across the
The rear seats of your vehicle are equipped withbuilt-in tether strap anchors located behind the seatson the package tray behind the speakers (coupe)
For Coupe only:4. Open the tetheranchor covers.5. Clip the tether strapto the anchor asshown.For Convertible only:The tether anchors onthe convertible
If the tether strap is clipped incorrectly, thechild safety seat may not be retainedproperly in the event of a collision.6. Refer to the Installing ch
Your vehicle has LATCH anchors for child seatinstallation at the seating positions marked with thechild seat symbol.The center ofthe rear seat isNOT d
The lower anchors forchild seat installationare located at the rearsection of the rear seatbetween the cushionand seat back. TheLATCH anchors arebelow
STARTINGPositions of the ignition1. ACCESSORY, allowsthe electricalaccessories such as theradio to operate whilethe engine is notrunning.2. LOCK, lock
Preparing to start your vehicleEngine starting is controlled by the powertraincontrol system. This system meets all CanadianInterference-Causing Equip
Important safety precautionsWhen the engine starts, the idle RPM runs faster towarm the engine. If the engine idle speed does notslow down automatical
Commentaires sur ces manuels