Introduction 4Instrument Cluster 12Warning and control lights 12Gauges 16Entertainment Systems 20AM/FM stereo 20AM/FM stereo cassette 22AM/FM stereo c
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
Child booster seatsChildren outgrow a typical convertible or toddler seat when they weigh40 pounds and are around 4 years of age. Although the lap/sho
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
Follow all instructions provided by the manufacturer of thebooster seat.Never put the shoulder belt under a child’s arm or behind theback because it e
When installing a child safety seat:• Review and follow the informationpresented in the Air bagsupplemental restraint system(SRS) section in this chap
Installing child safety seats with combination lap and shoulderbelts1. Position the child safety seat in aseat with a combination lap andshoulder belt
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with knee on thechild seat.8. Al
The SuperCab rear seat has three straps behind the top of the seat backthat function as both routing loops for the tether straps and anchorloops.The t
installing the child seat. Refer to the Folding down the rear seatssection in this chapter for information on how to operate the rear seats.5. Clip th
Many tether straps cannot be tightened if the tether strap is hooked tothe loop directly behind the child seat. To provide a tight tether strap:1. Rou
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo
Extended idling at high engine speeds can produce very hightemperatures in the engine and exhaust system, creating the riskof fire or other damage.Do
If starting a vehicle with an automatic transmission:• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).If starting a vehicle
• Turn the key to 4 (ON) withoutturning the key to 5 (START).Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to i
Using the engine block heater (if equipped)Use of an engine block heater isstrongly recommended if you live ina region where temperatures reach-23° C
Four-wheel anti-lock brake system (ABS) (if equipped)Your vehicle may be equipped with an Anti-lock Braking System (ABS).This system helps you maintai
Parking brakeTo set the parking brake, press theparking brake pedal down until thepedal stops. The BRAKE warninglamp in the instrument clusterillumina
STEERINGTo prevent damage to the power steering system:• Never hold the steering wheel at its furthest turning points (until itstops) for more than a
Loaded vehicles, with a higher center of gravity, may handledifferently than unloaded vehicles. Extra precautions, such asslower speeds and increased
If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly.See your dealer or a qua
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa
(Overdrive) can be deactivatedby pressing the transmission controlswitch on the end of the gearshiftlever. This will illuminate the O/DOFF lamp and ac
• Depress the accelerator to the floor.• Allows transmission to select an appropriate gear.Shift strategy (4R100 automatic transmission)To account for
To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)Always set the parking brake full
transmission is in the D (Overdrive) position; this engine braking willslow the vehicle and assist the driver in controlling the vehicle whendescendin
Do not rock the vehicle if the engine is not at normal operatingtemperature or damage to the transmission may occur.Do not rock the vehicle for more t
Recommended shift speedsDownshift according to the following charts for your specificengine/drivetrain combination:Maximum downshift speeds16-speed tr
REVERSE SENSING SYSTEM (IF EQUIPPED)The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when the R (Rev
The RSS detects obstacles up to 2meters (6 ft.) from the rear bumperwith a decreased coverage area atthe outer corners of the bumper,(refer to the fig
FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED)For important information regarding safe operation of this typeof vehicle, see Preparing to drive your v
• is operated by a rotary control located on the instrument panel thatallows you select 2WD, 4x4 High or 4x4 Low operation.• uses auto-manual hub lock
Check gage: Illuminates when anyof the following conditions hasoccurred:• The engine coolant temperatureis high.• The engine oil pressure is low.• The
N (Neutral) – Only used when towing the vehicle.4L (4WD Low)– For low-speed off-road applications that require extrapower such as steep grades, deep s
Shifting from 4H (4WD High) to 4L (4WD Low)1. Bring the vehicle to a complete stop.2. Depress the brake.3. Place the gearshift lever in N (Neutral) (a
This position should only be usedwhen towing the vehicle.Do not leave the vehicle unattended with the transfer case in theN (Neutral) position. Always
Shifting from 2WD (2WD High) to 4x4 HIGH (4WD High)Rotate the 4WD control to the 4x4HIGH position at speeds up to 88km/h (55 mph).• The electronic shi
4. Move the 4WD control to the 4x4LOW position.5. Hold the shift conditions until theLOW RANGE indicator lightilluminates.6. If the LOW RANGE indicato
Maintain steering wheel control at all times, especially in rough terrain.Since sudden changes in terrain can result in abrupt steering wheelmotion, m
Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.
not more. Additionally, smooth variations of the accelerator and/orbrake pedal pressure should be utilized if changes in vehicle speed arecalled for.
Power is supplied to all four wheelsthrough a transfer case. On 4WDvehicles, the transfer case allowsyou to select 4WD when necessary.Information on t
Once through water, always try the brakes. Wet brakes do not stop thevehicle as effectively as dry brakes. Drying can be improved by movingyour vehicl
Safety belt: Reminds you to fastenyour safety belt. A chime will alsosound to remind you to fasten yoursafety belt.Charging system: Illuminates whenth
When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This r
Avoid sudden braking as well. Although a 4WD vehicle may acceleratebetter than a two-wheel drive vehicle in snow and ice, it won’t stop anyfaster, bec
Tires can be damaged during off-road use. For your safety, tires that aredamaged should not be used for highway driving because they are morelikely to
and adversely affect driver and passenger safety. Frequent inspection ofvehicle chassis components is recommended if the vehicle is subjected toheavy
VEHICLE LOADINGBefore loading a vehicle, familiarize yourself with the following terms:• Base Curb Weight: Weight of the vehicle including any standar
Always ensure that the weight of occupants, cargo and equipment iswithin the weight limitations, including both gross vehicle weight andfront and rear
2nd unit bodies are not included in maximum trailer weight ratings. Theweight of the additional “body” must be subtracted from the maximumtrailer weig
F-250 Regular Cab PickupEngine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x2 with automatic transmission5.4L 3.73 6123 (135
F-250 SuperCab PickupEngine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x2 with manual transmission5.4L 3.73 6123 (13500) 33
F-250 SuperCab PickupEngine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x4 with automatic transmission5.4L 3.73 6123 (13500)
Four wheel drive low(if equipped): Illuminates whenfour-wheel drive low is engaged.Four wheel drive indicator(if equipped): Illuminates whenfour-wheel
F-250 Crew Cab PickupEngine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x2 with automatic transmission5.4L 3.73 6123 (13500)
F-350 Regular Cab Single Rear Wheel PickupEngine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x2 with manual transmission5.4L
F-350 Regular Cab Single Rear Wheel PickupEngine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x4 with automatic transmission5
F-350 Regular Cab Dual Rear Wheel PickupEngine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x4 with automatic transmission5.4
F-350 SuperCab Single Rear Wheel PickupEngine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x4 with manual transmission5.4L 3.
F-350 SuperCab Dual Rear Wheel PickupEngine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x2 with manual transmission5.4L 3.73
F-350 SuperCab Dual Rear Wheel PickupEngine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x4 with manual transmission5.4L 3.73
F-350 Crew Cab Single Rear Wheel PickupEngine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x2 with manual transmission5.4L 3.
F-350 Crew Cab Single Rear Wheel PickupEngine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x4 with automatic transmission5.4L
F-350 Crew Cab Dual Rear Wheel PickupEngine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x2 with automatic transmission6.8L 3
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
F-350 Crew Cab Dual Rear Wheel PickupEngine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x4 with automatic transmission6.8L 3
F-350 Regular Chassis Cab Single Rear Wheel (Fifth WheelTowing)Engine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x4 with au
F-350 Regular Chassis Cab Dual Rear Wheel (Fifth WheelTowing)Engine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x4 with auto
F-350 SuperCab Chassis Cab Dual Rear Wheel (Fifth WheelTowing)Engine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x2 with man
F-350 Crew Cab Chassis Cab Single Rear Wheel (Fifth WheelTowing)Engine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x4 with m
F-450 Regular Chassis Cab Dual Rear Wheel (Fifth WheelTowing)Engine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x2 with manu
F-450 Crew Cab Chassis Cab Dual Rear Wheel (Fifth WheelTowing)Engine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x2 with man
F-550 SuperCab Chassis Cab Dual Rear Wheel (Fifth WheelTowing)Engine Rear axleratioMaximum GCWR -kg (lbs.)Maximumtrailer weight -kg (lbs.)4x2 with aut
Load equalizing hitchWhen hooking up a trailer using a load equalizing hitch, always use thefollowing procedure:1. Park the unloaded vehicle on a leve
Using a step bumper (if equipped)The rear bumper is equipped with an integral hitch and only requires aball with a 25.4 mm (one inch) shank diameter.
Trip odometer: Registers thekilometers (miles) of individualjourneys. To reset, depress thecontrol.Tachometer: Indicates the enginespeed in revolution
• To aid in engine/transmission cooling and A/C efficiency during hotweather while stopped in traffic, place the gearshift lever in P (Park)(automatic
RWD vehicles with 4x4 electronic shift transfer case or All WheelDrive (AWD) vehicles with automatic transmissions:Regarding recreational towing or ha
• The Front Axle Accessory Reserve Capacity and the TARC listed onthe bottom right of the Safety Compliance Certification Label willdetermine whether
Snowplowing with your air bag-equipped vehicleYour vehicle is equipped with a driver and passenger air bagSupplemental Restraint System (SRS) The SRS
4WD operation while plowing• Shift transfer case to 4x4 LOW (4WD Low) when plowing in smallareas at speeds below 8 km/h (5 mph).• Shift transfer case
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
This switch is located in the frontpassenger’s footwell, by the kickpanel access cover.To reset the switch:1. Turn the ignition OFF.2. Check the fuel
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey ———3A Violet Vio
To remove a fuse use the fuse pullertool provided on the fuse panelcover.The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Comp
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe
Fuse/RelayLocationFuse AmpRatingPassenger Compartment Fuse PanelDescription12 20A* Cigar lighter / OBD II13 5A* Power mirrors/switches14 15A* Daytime
Fuse/RelayLocationFuse AmpRatingPassenger Compartment Fuse PanelDescription36 10A* PCM Memory37 15A* Horn38 20A* Trailer tow park lamps39 15A* Trailer
Fuse/RelayLocationFuse AmpRatingPassenger Compartment Fuse PanelDescription602 60A** 4WABS module210 — Not used211 — Backup lamps relay (Diesel engine
If your vehicle is equipped with 4WD, a spare tire of a differentsize than the road tires should not be used. Use of such a tirecould result in damage
• Vehicles equipped with dualrear wheels, insert the lugwrench extension into the lugwrench to reach the lug nuts.2. Attach the spare tire lock key (A
Tire change procedure1. Park on a level surface, activatehazard flashers and set the parkingbrake.• Automatic transmission: Placegearshift lever in P
5. Loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground.When one of the rear wheels i
• Front passenger side (4x4)• Front driver side (4x4)Make sure the jack fits into thenotched area next to the differentialhousing.• RearRoadside Emerg
Never use the front or reardifferential as a jacking point.To lessen the risk ofpersonal injury, do not putany part of your body under thevehicle whil
13. Position the jack according to the following guides:• Front (4x2) F350• Front (4x2) F450/550• Front driver side (4x4)Roadside Emergencies189
Red area (over temperature) —the transmission fluid is overheating.Stop the vehicle to allow thetemperature to return to normalrange.If the gauge is o
• Front passenger side (4x4)• Rear14. Insert the jack handle into thepump linkage.15. Use an up-and-down motionwith the jack handle to raise thewheel
The following steps apply to all vehicles:19. Remove the jack and fullytighten the lug nuts in the ordershown.20. Stow the flat tire. Refer toStowing
When a wheel is installed, always remove any corrosion, dirt orforeign materials present on the mounting surfaces of the wheelor the surface of the fr
JUMP STARTING YOUR VEHICLEThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury
Connecting the jumper cables1. Connect the positive (+) booster cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
• lift the rear wheels of the vehicle using a wheel lift or a sling belt withT-hooks.If the vehicle is towed by other means or incorrectly, vehicledam
Locks and Security 65Keys 65Locks 65Anti-theft system 67Seating and Safety Restraints 72Seating 72Safety restraints 77Air bags 90Child restraints 99Dr
AM/FM STEREO1. Seek: Press/ to find thenext strong station down/up thefrequency band.2. Tune: Press/ to manuallychange radio frequency down/up.3. AM/F
GETTING THE SERVICES YOU NEEDAt homeFord Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
• available free to owners and lessees of qualifying Ford Motor Companyvehicles.The Dispute Settlement Board may not be available in all states. FordM
• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Board membership are recruited and trained byan independent consulting fi
before the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral presentationmay be
The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have
If you are in another foreign country, contact the nearest Forddealership. If the dealership employees cannot help you, they can directyou to the near
1. Two or more repair attempts are made on the same nonconformitylikely to cause death or serious bodily injury OR2. Four or more repair attempts are
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
5. Power/volume: Press to turnON/OFF; turn to increase ordecrease volume levels.6. Tone: Press TONE until thedesired level — Bass, Treble, Fadeappears
PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam
• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTIC (NON-PAINTED) EXTERIOR PARTSUse onl
INSTRUMENT PANEL AND CLUSTER LENSClean the instrument panel with a damp cloth, then dry with a dry cloth.• Avoid cleaners or polish that increase the
LEATHER SEATS (IF EQUIPPED, EXCEPT FOR THE KING RANCHF–250 AND F–350 CREWCAB)Your leather seating surfaces have a clear, protective coating over thele
SCRATCHESIn order to lessen the appearance of certain scratches and other wearmarks, apply conditioner on the affected area following the sameinstruct
Motorcraft Deluxe Leather and Vinyl Cleaner (not available in Canada)(ZC-11–A)Ford Extra Strength Tar and Road Oil Remover* (not available inCanada) (
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
• Manual transmission:1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral).2. Block the wheels.Note: Do not start your e
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT5.4L V8/6.8L V10 gasoline enginesRefer to the 6.0 Liter Power Stroke Direct Injection Turbo DieselOwne
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
AM/FM STEREO CASSETTE1. Balance: Press to shift sound tothe left/right speakers.2. Fade: Press to shift sound to therear/front speakers.3. CLK: To set
5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.•
3. Recheck the engine oil level. Make sure the oil level is not above theMAX mark on the engine oil level indicator (dipstick).4. Install the indicato
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “cold fill level” or within the “c
Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant couldmake it difficult to see through
For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when
Recycled engine coolantFord Motor Company recommends the use of a recycled engine coolantproduced by Ford-approved processes in vehicles originally eq
• Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may cause engine da
next selection). Then, press REW (for the beginning of the currentselection) or FF (to advance to the next selection). The tape MUST havea blank secti
Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to a service facility as soon as possible to minimize enginedamage.W
Automotive fuels can cause serious injury or death if misused ormishandled.Gasoline may contain benzene, which is a cancer-causing agent.Observe the f
When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke whilerefueling. Fuel vapor is extreme
be void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used.The fuel system may be und
in the United States) because it may cause these problems to becomemore pronounced. If the problems persist, see your dealer or a qualifiedservice tec
Replace the fuel filter with an authorized Motorcraft part. Thecustomer warranty may be void for any damage to the fuel systemif an authorized Motorcr
• Have the vehicle loading and distribution the same every time.Your results will be most accurate if your filling method is consistent.Calculating fu
• Revving the engine before turning it off may reduce fuel economy.• Using the air conditioner or defroster may reduce fuel economy.• You may want to
• Four-wheel-drive operation (if equipped) is less fuel efficient thantwo-wheel-drive operation.• Close windows for high speed driving.EPA window stic
Exhaust leaks may result in entry of harmful and potentiallylethal fumes into the passenger compartment.Do not make any unauthorized changes to your v
12. Power/volume: Press to turnON/OFF; turn to increase ordecrease volume levels.13. AM/FM: Press to choose afrequency band in radio mode.14. Bass: Pr
Soon” light is on, refer to the description in the Warning lights andchimes section of the Instrument cluster chapter. Your vehicle may notpass the I/
6. Recheck the fluid level on the dipstick. Do not add fluid if the level isbetween the arrows in the FULL COLD range.7. If the fluid is low, add flui
1. Clean the reservoir cap beforeremoval to prevent dirt and waterfrom entering the reservoir.2. Remove cap and rubberdiaphragm from reservoir.3. Add
4. Latch the gearshift lever in P (Park) and leave the engine running.5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. Ifneces
Adjusting automatic transmission fluid levelsBefore adding any fluid, make sure the correct type is used. The type offluid used is normally indicated
Checking and adding manual transmission fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Fluid leve
Checking and adding transfer case fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough
Note: Do not start your engine with the air cleaner removed and do notremove it while the engine is running.Changing the air filter element (gasoline
• Treadwear 200 Traction AA Temperature AThese Tire Quality Grades are determined by standards that the UnitedStates Department of Transportation has
which all passenger car tires must meet under the Federal Motor VehicleSafety Standard No. 109. Grades B and A represent higher levels ofperformance o
PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD1. Power/volume: Press to turnON/OFF; turn to increase/decreasevolume.2. Scan: Press to hear a briefsampling of
Tire inflation informationThe F450 and F550 vehicles are equipped with a tire that is an all-steelradial. All-steel radial tires utilize steel cords i
• Four tire rotation• Five tire rotationMaintenance and Specifications251
• DRW – Six tire rotationIf your vehicle is equipped with dualrear wheels it is recommended thatfront and rear tires (in pairs) berotated only side to
Make sure that all replacement tires are of the same size, type,speed rating, load-carrying capacity and tread design (e.g., “AllTerrain”, “Touring”,
MOTORCRAFT PART NUMBERSComponent* 5.4L V8 engine 6.8L V10 engineAir filter element FA-1634 FA-1634Fuel filter FG-986B FG-986BOil filter FL-820-S FL-82
FluidFord PartNameApplication CapacityRear axle1,2Motorcraft SAE75W-140Synthetic RearAxle LubricantF-250 /350(10.50 inchaxle)3.3L (6.9 pints)Motorcraf
FluidFord PartNameApplication CapacityFuel tank N/A Mid-ship tank(optional onChassis Cab)71.9L (19.0gallons)Right sidesaddle mountedtank (optionalon C
1Your vehicle’s rear axle(s) may be filled with a synthetic lubricant thatmay require a lubricant change. Refer to the scheduled maintenanceguide. Axl
LUBRICANT SPECIFICATIONSItemFord partname orequivalentFord partnumberFordspecificationSpindle bearingHighTemperature4X4 Front Axleand WheelBearing Gre
ItemFord partname orequivalentFord partnumberFordspecificationEngine coolant MotorcraftPremium EngineCoolant(green-colored)VC-4–A (inCanada,Motorcraft
4. Cassette door: Insert thecassette with the opening to theright.5. Eject: Press to eject thecassette/CD. The radio will resumeplaying.6. Tape: Press
ItemFord partname orequivalentFord partnumberFordspecificationManualtransmission(6-speed)MotorcraftMERCON威 ATF2XT-2-QDX MERCON威Automatictransmission4R
MERCON威, MERCON威 V and MERCON威 SP are notinterchangeable. DO NOT mix MERCON威, MERCON威 V andMERCON威 SP. Use of dual usage fluids in an automatictransmi
Dimension Body styleRegularCab 4x2RegularCab 4x4Super Cab4x2Super Cab4x4(4)Wheelbase3 479.8 mm(137 in)3 479.8 mm(137 in)3 610.7 mm(141.8 in)a4 013.2 m
F350–except Crew CabDimension Body styleChassisCab —RegularCabChassisCab —Super CabRegularCab StyleSideSuper CabStyle Side(1) Overallheight1 924 mm(75
Dimension Body styleChassisCab —RegularCabChassisCab —Super CabRegularCab StyleSideSuper CabStyle Side(4)Wheelbase3 576 mm(140.8 in)4 186 mm(164.8 in)
DimensionBody styleCrew chassisCabCrew cab-shortboxCrew cab —long box(2b) Track —Rear1 729 mm(68.1 in)a,c/1 803 mm(74.0 in)b,d1 729 mm(68.1 in)a,c/1 8
Dimension Body styleRegularCabChassis 4x2RegularCabChassis 4x4Super CabChassis4x2/4x4Crew CabChassis4x2/4x4(2) Track(Front /Rear)1 736 mm(68.4 in) /1
F550Dimension Body styleRegularCabChassisCab 4x2RegularCabChassisCab 4x4Crew CabChassisCab 4x2Crew CabChassisCab 4x4(1) Overallheight2 076 mm(81.7 in)
Dimension Body styleRegularCabChassisCab 4x2RegularCabChassisCab 4x4Crew CabChassisCab 4x2Crew CabChassisCab 4x4(5) Overalllength5 733 mm(225.7 in)a6
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
10. Balance: Press BAL; then pressSEL/ to shift sound to theleft/right speakers.Fade: Press FADE; then pressSEL/ to shift sound to therear/front speak
Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea
FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincol
Box Aluminum Rack cargo storage systems (Trac Rac)Daytime running lights (DRL)Electrochromic inside mirror with compassElectrochromic inside mirror wi
Door edge guardsFender flaresFlat splash guardsFront end covers (full)Hood deflectorsLeather wrap steering wheelLocking gas capLubricants and oilsMold
• Mobile communications systems may harm the operation of yourvehicle, particularly if they are not properly designed for automotiveuse or are not pro
AAccessory delay ...54Air bag supplemental restraintsystem ...90and child safety seats .
washing ...209waxing ...209wheels ...210wiper bl
refill capacities ...254specifications ...258, 261Exhaust fumes ...114FFail safe cooling ..
Inspection/maintenance (I/M)testing ...239Instrument panelcleaning ...212cluster
Power distribution box(see Fuses) ...178Power door locks ...65, 70Power point ...
18. Select (SEL): Use with Bass,Treble, Balance and Fade controls.19. Bass: Press BASS; then pressSEL/ to decrease/increasethe bass output.Treble: Pre
Traction-lok rear axle ...117Transfer casefluid checking ...246Transmissionautomatic operation ...50, 118fluid
PREMIUM IN-DASH SIX CD SOUND SYSTEM1. Seek: Press and releaseSEEK/ for previous/nextstrong station, or track of currentdisc.2. Rewind: Press for a slo
Maintenance and Specifications 216Engine compartment 218Engine oil 219Battery 222Fuel information 230Air filter(s) 247Part numbers 254Refill capacitie
6. Bass: Press BASS; then pressSEL/ to decrease/increasethe bass output.Treble: Press TREB; then pressSEL/ to decrease/increasethe treble output.7. Se
10. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, press andhold a preset button until soundreturns. In CD mode, pres
17. Disc/Tune: Radio: Pressor to manually tune down or upthe frequency band.CD: Pressor to select the previous or next track on the CD.18. CD door: In
5. Line up the CD with the grooveof the disc holder. Ensure that thelabel on the CD faces downwards.6. Press the disc holder until it lockssecurely in
Keep the CD changer door closed. Coins and foreign objects will damagethe CD player and void your audio system warranty.RADIO FREQUENCIESAM and FM fre
CD/CD PLAYER CAREDo:• Handle discs by their edges only. Never touch the playing surface.• Inspect discs before playing. Clean only with an approved CD
HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe
4. Direct the outer instrument panel vents towards the side windowsTo increase airflow to the outer instrument panel vents, close the ventslocated in
• Under normal weather conditions, do not leave the air flow selector inMAX A/C or OFF when the vehicle is parked. This allows the vehicleto “breathe”
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
Foglamp control (if equipped)The headlamp control also operatesthe foglamps. The foglamps can beturned on only when the headlampcontrol is in the, orp
Flash to passPull toward you slightly to activateand release to deactivate.PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and
COURTESY/READING LAMPS (IF EQUIPPED)The dome lamp lights when thecontrol is in the DOOR (left)position, any door is open, theinstrument panel switch i
“E” for Europe to assure lamp performance, light brightness and patternand safe visibility. The correct bulbs will not damage the lamp assemblyor void
3. Remove bulb retainer ring byturning it counterclockwise, thenslide the ring off the plastic base4. Pull bulb out of headlampassembly.Handle a halog
5. Remove the four screws and theheadlamp retaining ring fromheadlamp.6. Disconnect the electricalconnector and remove headlamp.Install the new bulb(s
Replacing tail lamp/turn/backup lamp bulbs — F250/F350 only1. Make sure the headlamp switch isin the OFF position and then openthe tailgate to expose
Replacing cargo lamp and high-mount brakelamp bulbs1. Make sure the headlamp switch isin the OFF position.2. Remove the two screws and lampassembly fr
Replacing license plate lamp bulbsThe license plate bulbs are locatedbehind the rear bumper. To changethe license plate lamp bulbs:1. Reach behind the
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
Fuel pump shut-off switch In the event of an accident thesafety switch will automatically cut off the fuel supply to theengine. The switch can also be
TILT STEERING WHEEL (IF EQUIPPED)To adjust the steering wheel:1. Pull and hold the steering wheelrelease control toward you.2. Move the steering wheel
ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamps.OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehi
5. Place the height adjusters ontothe back of the storagecompartment door. Add as manyadjusters needed to activate thegarage door opener.6. Close the
To tilt the moon roof:• To tilt into the vent position (when the glass panel is closed), pressand hold the front portion of the moon roof control. To
One touch downAllows the driver’s window to openfully without holding the controldown. Press completely down onAUTO and release quickly. Pressagain to
Heated outside mirrors (if equipped)Both main mirrors are heatedautomatically to remove ice, mistand fog. The mirrors areautomatically activated when
Running lampsIlluminates when the headlamps orparking lamps are on.This provides additional visibility ofyour vehicle to other drivers on theroad.Fold
POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is
3. Press the SET ACCEL controland release it.4. Take your foot off the acceleratorpedal.5. The indicator light on theinstrument cluster will turn on.N
Reducing speed while using speed controlThere are two ways to reduce a setspeed:• Press and hold the COASTcontrol until you get to thedesired speed, t
BREAKING-IN YOUR VEHICLEYour vehicle does not need an extensive break-in. Try not to drivecontinuously at the same speed for the first 1,600 km (1,000
CENTER CONSOLE (IF EQUIPPED)Your vehicle may be equipped with a variety of console features. Theseinclude:• Utility compartment withcassette/CD holder
Selectable featuresEnglish/metric displayPress this control to change the tripcomputer display between metricand English units.Mode controlEach press
2. Press the E/M and MODEcontrols simultaneously. The displaywill illuminate the “AVG” indicator.While the indicator is lit, releaseboth controls to r
The compass heading is displayed in average fuel economy modes, fuelrange modes and temperature modes.The compass reading may be affected when you dri
3. Press and hold both tripcomputer controls. Afterapproximately eight seconds, thetrip computer will enter CAL mode.CAL mode is indicated when thedis
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
Childproof door locks• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the
Your vehicle is equipped with a remote entry system which allows you to:• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta
The UNLOCK feature will work again after:• a door has become ajar,• the ignition is turned to the ON position, or• using the UNLOCKcontrol on your rem
• structures around the vehicle and• other vehicles parked next to the vehicle.To replace the battery:1. Twist a thin coin between the twohalves of th
Data RecordingComputers in your vehicle are capable of recording detailed datapotentially including but not limited to information such as:• the use o
5. The doors will lock, then unlock, to confirm that the programmingmode has been activated.6. Within 20 seconds press any button on the remote entry
• the brake is pressed before reaching 8 km/h (5 mph) and• the vehicle is traveling more than 8 km/h (5 mph).RelockThe autolock feature repeats when t
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
40/20/40 split bench seat (if equipped)• Lift the track release bar to movethe seat forward or backward.Ensure the seat is relatched intoplace.• Pull
To gain access to the storagecompartment in your armrest, liftthe latch to open the lid. The lidcannot be opened in the uprightposition.Captain’s chai
Press to raise or lower the frontportion of the seat cushion.• Type A• Type BPress to raise or lower the rearportion of the seat cushion.• Type A• Typ
• Type BPress the control to move the seatforward or backward.Using the manual lumbar supportFor more lumbar support, turn thelumbar support control t
1. Pull lever to release seat cushion.2. Rotate seat cushion up until itlocks into vertical storage position.RETURNING THE SEAT TO SEATING POSITIONAlw
It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in these areasare more likely to be se
2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.The front outboard and rear outboard safety restraints in the vehicle arec
Notice to owners of diesel-powered vehiclesRead the 6.0 Liter Power Stroke Direct Injection Turbo Diesel Owner’sGuide Supplement for information regar
How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt
BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe seat belt assembly “automatic locking retractor” feature orany other seat belt function is not oper
In the event of a collision, thecolored label (REPLACE BELT)may become visible. If this occurs,the safety belt must be replaced.Whenever the yellowpor
is involved in a collision that results in the activation of the safety beltpretensioners. Refer to the Safety belt maintenance section in thischapter
Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could re
into the correct buckle. If you did not pull out enough webbing to reachthe buckle, allow the tongue to retract fully before trying to pull it outagai
If... Then...The driver’s safety belt is notbuckled before the vehicle hasreached at least 5 km/h (3 mph)and 1-2 minutes have elapsedsince the ignitio
Reasons given... Consider...“Traffic is light” Nearly 1 of 2 deaths occur in single-vehiclecrashes, many when no other vehicles are around.“Belts wrin
• The driver’s safety belt is unbuckled.• The parklamps/headlamps are in OFF position (If vehicle is equippedwith Autolamps, this will not affect the
Safety belt extension assemblyIf the safety belt is too short when fully extended, there is a 20 cm(8 inch) safety belt extension assembly that can be
If your vehicle is equipped with theFord Ambulance PreparationPackage, it will be indicated on theCertification label. The label islocated on the driv
AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and righ
Never place your arm over the air bag module as a deploying airbag can result in serious arm fractures or other injuries.To properly position yourself
Children and air bagsFor additional important safety information, read all information onsafety restraints in this guide.Children must always be prope
cause minor abrasions, swelling or temporary hearing loss. Because airbags must inflate rapidly and with considerable force, there is the risk ofdeath
A difficulty with the system is indicated by one or more of the following:• The readiness light will eitherflash or stay lit.• The readiness light wil
Turning the passenger air bag off1. Insert the ignition key, turn theswitch to OFF position and hold inOFF position while removing thekey.2. When the
The passenger side air bag should always be ON (the air bag OFF lightshould not be illuminated) unless the passenger is a person who meetsthe requirem
Read all air bag Warning labels in the vehicle as well as the otherimportant air bag instructions and Warnings in this Owner’s Guide.NHTSA deactivatio
Transport Canada deactivation criteria (Canada Only)1. Infant: An infant (less than 1 year old) must ride in the front seatbecause:• my vehicle has no
SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Air bag supplem
Commentaires sur ces manuels