Introduction 4Instrument Cluster 12Warning and control lights 12Gauges 16Entertainment Systems 20AM/FM stereo cassette 20AM/FM stereo with CD 22AM/FM
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
• Front seats• Rear seats (if equipped)The front and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front p
When to use the automatic locking mode• Anytime a child safety seat is installed in a passenger front oroutboard rear seating position with Regular Ca
2. Grasp the shoulder portion andpull downward until the entire beltis extracted.3. Allow the belt to retract. As the belt retracts, you will hear a c
CrewCab base bench seats and all Regular Cab seating positions, thesafety belts are equipped with a retractor pretensioner.The driver and front outboa
• 4–door SuperCab (Bench seatsonly)To lower the shoulder belt height, push the button and slide the heightadjuster down. To raise the height of the sh
Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war
If... Then...The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition...The BeltMinder feature will notactivate.The fo
Reasons given... Consider...“The people I’m with don’twear belts”Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE peop
• All vehicle doors are closed.• The driver’s safety belt is unbuckled.• The parklamps/headlamps are in OFF position (If vehicle is equippedwith Autol
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
Safety belt extension assemblyIf the safety belt is too short when fully extended, there is a 20 cm (8inch) safety belt extension assembly that can be
AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and righ
The National Highway Traffic Safety Administration (NHTSA)recommends a minimum distance of at least 25 cm (10 inches)between an occupant’s chest and t
Children must always be properly restrained. Failure to follow theseinstructions may increase the risk of injury in a collision.An infant in a rear-fa
internal injuries, particularly to occupants who are not properlyrestrained or are otherwise out of position at the time of air bagdeployment. Thus, i
A difficulty with the system is indicated by one or more of the following:• The readiness lights will eitherflash or stay lit.• The readiness lights w
Turning the passenger air bag off1. Insert the ignition key, turn theswitch to OFF position and hold inOFF position while removing thekey.2. When the
Turning the passenger air bag back onThe passenger air bag remains OFF until you turn it back ON.1. Insert the ignition key and turnthe switch to ON.2
Always transport children who are 12 and younger in the rearseat. Always use safety belts and child restraints properly. If achild in a rear facing in
• the child has a medical condition which, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the dr
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterHarley—Davidson instrument clusterLHLHEFCHSELECT/RESETPREMIUMUNLEADEDFU
Important child restraint precautionsYou are required by law to use safety restraints for children in the U.S.and Canada. If small children (generally
Booster seats position a child so that safety belts fit better. They lift thechild up so that the lap belt rests low across the hips and the kneesbend
• Those with a high back.If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo
SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully fo
positions-Regular Cab and SuperCab) (passenger side front and rearseating positions-SuperCrew) (if equipped).Ford recommends the use of a child safety
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a
Installing child safety seats in the front row lap belt seatingpositions1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that itsbot
8. Before placing the child in the seat, forcibly move the seat forwardand side-to-side to make sure the seat is securely held in place.9. Check to ma
• F150 SuperCab• F150 SuperCrew• F150 SuperCrew with quad bucketsTether strap attachment1. Position the child safety seat on the seat cushion.2. Route
Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate
• Front seat (Regular Cab andSuperCab only)• Rear seats ( with quad bucketsonly)2003 F150 (f12)Owners Guide (post-2002-fmt)USA English (fus)Seating an
• Rear seats (SuperCrew only)If the tether strap is clippedincorrectly, the child safetyseat may not be retained properlyin the event of a collision.5
Many tether straps cannot be tightened if the tether strap is hooked tothe loop directly behind the child seat. To provide a tight tether strap:1. Rou
Attaching safety seats with LATCH (Lower Anchors and Tethers forChildren) attachments for child seat anchors (if equipped)Some child safety seats have
• F150 SuperCrew with Quad BucketsThe anchors on both sides of the center of the SuperCrew rear seat areprovided only for child seats at the outboard
If you install a child seat with rigid LATCH attachments, do not tightenthe tether strap enough to lift the child seat off the vehicle seat cushionwhe
STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo
Extended idling at high engine speeds can produce very hightemperatures in the engine and exhaust system, creating the riskof fire or other damage.Do
• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).If starting a vehicle with a manualtransmission:1. Make sure the parking b
• Turn the key to 4 (ON) withoutturning the key to 5 (START).123452003 F150 (f12)Owners Guide (post-2002-fmt)USA English (fus)Driving139
Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance mayoccur. It will take you longer
Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced.• If the driver’s safety
To reduce the risk of electrical shock, do not use your heaterwith ungrounded electrical systems or two-pronged (cheater)adapters.Guarding against exh
Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake
If the power steering system breaks down (or if the engine is turnedoff), you can steer the vehicle manually, but it takes more effort.If the steering
Loaded vehicles, with a higher center of gravity, may handledifferently than unloaded vehicles. Extra precautions, such asslower speeds and increased
If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly.See your dealer or a qua
(Overdrive)The normal driving position for thebest fuel economy. Transmissionoperates in gears one through four.Overdrive can be deactivated bypressin
1 (First)• Provides maximum engine braking.• Allows upshifts by moving gearshift lever.• Will not downshift into 1 (First) at high speeds; allows for
MANUAL TRANSMISSION OPERATION (IF EQUIPPED)Using the clutchThe manual transmission has a starter interlock that prevents crankingthe engine unless the
4.2L V6 engineUpshifts when accelerating (recommended for best fueleconomy)Shift from: Transfer case position (if equipped)2H or 4H 4L1 - 2 24 km/h (1
Low fuel: Illuminates when the fuellevel in the fuel tank is at, or nearempty (refer to Fuel gauge in thischapter).Low washer fluid: Illuminateswhen t
Upshifts when cruising (recommended for best fuel economy)Shift from: Transfer case position (if equipped)2H or 4H 4L1 - 2 16 km/h (10 mph) 6 km/h (4
All applicationsMaximum downshift speeds1Shift from: Transfer case position (if equipped)2H or 4H 4LD(Overdrive) -489 km/h (55 mph) 34 km/h (21 mph)4
FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED)For important information regarding safe operation of this typeof vehicle, see Preparing to drive your v
4L (4WD Low)– Uses extra gearing to provide maximum power to allfour wheels at reduced speeds. Intended only for off-road applicationssuch as deep san
Using the electronic shift 4WD system (if equipped)2H (2WD High) - Power to the rear wheels only; used for street andhighway driving. Provides optimal
• If shifting into 4L (4WD Low), wait for the LOW RANGE light in theinstrument cluster to turn on indicating the shift is complete.• If shifting out o
pavement only after reducing your speed. Do not turn the steeringwheel too sharply while returning to the road surface.• It may be safer to stay on th
Do not spin the wheels at over 56 km/h (35 mph). The tires mayfail and injure a passenger or bystander.Emergency maneuvers• In an unavoidable emergenc
4WD Systems4WD (when you select a 4WD mode) uses all four wheels to power thevehicle. This increases traction, enabling you to drive over terrain andr
Mud and waterIf you must drive through highwater, drive slowly. Traction orbrake capability may be limited.When driving through water,determine the de
Turn signal: Illuminates when theleft or right turn signal or thehazard lights are turned on. If theindicators stay on or flash faster, check for a bu
slopes or hills. A danger lies in losing traction, slipping sideways andpossibly rolling over. Whenever driving on a hill, determine beforehandthe rou
Avoid sudden applications of power and quick changes of direction onsnow and ice. Apply the accelerator slowly and steadily when startingfrom a full s
Do not use “aftermarket lift kits” or other suspension modifications,whether or not they are used with larger tires and wheels.These “aftermarket lift
Ford Motor Company recommends that caution be used with any vehicleequipped with a high load or device (such as ladder racks or pickup boxcover).Failu
• GCW (Gross Combined Weight): The combined weight of thetowing vehicle (including occupants and cargo) and the loaded trailer.• GCWR (Gross Combined
Special loading instructions for owners of pickup trucks andutility-type vehiclesFor important information regarding safe operation of this typeof veh
Towing trailers beyond the maximum recommended gross trailerweight exceeds the limit of the vehicle and could result inengine damage, transmission dam
Engine Rear axle ratio MaximumGCWR-kg (lbs.)Maximumtrailerweight-kg (lbs.)Regular Cab 4x2 w/manual transmission4.2L 3.08 2944 (6500) 907 (2000)4.2L 3.
Engine Rear axleratio/tire size -cm (inches)MaximumGCWR-kg (lbs.)Maximumtrailerweight-kg (lbs.)5.4L 3.31/40.6 (16) 5443 (12000) 3175 (7000)5.4L 3.55/4
Preparing to towUse the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. See your dealer or a reliable trai
Harley—Davidson instrument cluster gaugesSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemp
Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s brake system. Your vehicle may not have enoughbraking power and your chanc
• Allow more distance for stopping with a trailer attached.• The trailer tongue weight should be 10–15% of the loaded trailerweight.• After you have t
If a distance of 80 km (50 miles) or a speed of 56 km (35 mph) must beexceeded, the drive shaft will have to be removed before the vehicle istowed.For
• The weight of the snowplow and supporting components distributed tothe front axle must not exceed the Front Axle Accessory ReserveCapacity.• The tot
Careless or high speed driving while plowing snow which results insufficient vehicle decelerations can deploy the air bag. Such driving alsoincreases
• If the vehicle is stuck, shift the transmission in a steady motionbetween forward and reverse gears. Do not rock the vehicle for morethan a few minu
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
This switch is located in the frontpassenger’s footwell, by the kickpanel access cover.To reset the switch:1. Turn the ignition OFF.2. Check the fuel
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
Trip odometer: Registers thekilometers (miles) of individualjourneys. Press the control once toswitch from the odometer to thetrip odometer. To reset
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 15A Audio2 5A Powertrain Control Module(PC
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description7 — Not used8 5A Radio, Remote entry module,GEM, In-vehicle entertainmentsy
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description23 10A Trailer tow battery Charge relay,Turn/Hazard flasher, 4x4solenoids,
Always replace the cover to the power distribution box beforereconnecting the battery or refilling fluid reservoirsIf the battery has been disconnecte
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription8 15A* Power door locks, CentralSecurity Module (CSM), Lockrelays (not used on SuperC
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription102 50/20A** Four-wheel Anti-lock BrakeSystem (4WABS)module/Rear-wheel Anti-lockBrake
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription206 — Fog lamp relay207 — Front washer pump relay208 — Intercooler pump relay(superch
Spare tire informationYour vehicle is equipped with a spare tire that may be used as a spare ora regular tire. The spare tire wheel may not match the
2. Attach the spare tire lock key (A)to the jack handle (B).3. Fully insert the jack handlethrough the bumper hole and intothe guide tube. The key and
1. Park on a level surface, activatehazard flashers and set the parkingbrake.2. Place gearshift lever in P (Park)(automatic transmission) or in therev
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe
When one of the rear wheels is off the ground, the transmissionalone will not prevent the vehicle from moving or slipping off thejack, even if the tra
• RearTo lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engine when yourve
• Seven lug nut wheel12. Stow the flat tire. Refer to Stowing the flat/spare tire.13. Stow the jack and lug wrench. Make sure the jack is fastened so
the tire is raised to the maximum tightness. Tighten to the best of yourability, to the point where the ratchet/slip occurs, if possible. The sparetir
4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level.5. Tu
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeFord Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you
Seating and Safety Restraints 90Seating 90Safety restraints 98Air bags 111Child restraints 119Driving 136Starting 136Brakes 141Transmission operation
AM/FM STEREO CASSETTE1. Balance: Press to shift sound tothe left/right speakers.2. Fade: Press to shift sound to therear/front speakers.3. CLK: To set
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or
The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedu
from Ford and Lincoln Mercury dealership management, recognized fortheir business leadership qualities.What the Board needsTo have your case reviewed
Making a decisionBoard members review all available information related to eachcomplaint, including oral presentations, and arrive at a fair and impar
In the CAMVAP program, impartial third-party arbitrators conducthearings at mutually convenient times and places in an informalenvironment. These impa
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
3. The vehicle is out of service for repair of nonconformities for a total ofmore than 30 calendar days (not necessarily all at one time)In the case o
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam
4. Tape AMS: In tape mode, pressand hold to activate AutomaticMusic Search (allows you to quicklylocate the beginning of the tape selection being play
• 4.2L V6 engine• 4.6L V8 and 5.4L V8 engine2003 F150 (f12)Owners Guide (post-2002-fmt)USA English (fus)Cleaning210
• 5.4L Supercharged V8 engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTIC (NON-P
INSTRUMENT PANEL AND CLUSTER LENSClean the instrument panel with a damp cloth, then dry with a dry cloth.• Avoid cleaners or polish that increase the
LEATHER SEATS (IF EQUIPPED, EXCEPT FOR THE KING RANCHSUPERCREW)Your leather seating surfaces have a clear, protective coating over theleather.For King
SCRATCHESIn order to lessen the appearance of certain scratches and other wearmarks, apply conditioner on the affected area following the sameinstruct
FORD, LINCOLN AND MERCURY CAR CARE PRODUCTSYour Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect i
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
Working with the engine on• Automatic transmission:1. Set the parking brake and shift to P (Park).2. Block the wheels.• Manual transmission:1. Set the
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.2L V6 engine1. Battery2. Engine oil filler cap3. Engine oil dipstick4. Clutch fluid reservoir (manua
4.6L V8/5.4L V8 engines1. Power steering fluid reservoir2. Clutch fluid reservoir (manual transmission)3. Engine oil dipstick4. Brake fluid reservoir5
13. AM/FM: Press to choose afrequency band in radio mode.14. Bass: Press/ todecrease/increase the bass output.15. Treble: Press/ todecrease/increase t
5.4L Supercharged V8 engine1. Engine oil dipstick2. Power steering fluid reservoir3. Brake fluid reservoir4. Power distribution box5. Engine coolant r
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
• 4.2L engine2003 F150 (f12)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specifications222
• 4.6L/5.4L engine5. Locate and carefully remove the engine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, th
• Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician.7. Put the indicator back in
Change your engine oil according to the appropriate schedule listed inthe scheduled maintenance guide.Ford production and aftermarket (Motorcraft) oil
Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lightedsubstances to come near th
• If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “cold fill level” or within the “c
Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant couldmake it difficult to see through
1. Balance: Press/ to shiftsound to the left/right speakers.2. Fade: Press/ to shiftsound to the front/rear speakers.3. SCN (Scan): Press to hear abri
1. Before you begin, turn the engine off and let it cool.2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the c
Fill your engine coolant reservoir as outlined in Adding engine coolantin this chapter.Severe climatesIf you drive in extremely cold climates (less th
How fail-safe cooling worksIf the engine begins to overheat:• The engine coolant temperaturegauge will move to the red (hot)area.• Theand the symbolwi
5. Restart the engine and take your vehicle to a service facility.Driving the vehicle without repairing the engine problemincreases the chance of engi
• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kindcan lead to eye and respiratory tract irritation. In severe cases,excessive or p
Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1/8 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref
Repairs to correct the effects of using a fuel for which your vehicle wasnot designed may not be covered by your warranty.Octane recommendationsYour v
performance and emission control system protection for your vehicle.Gasolines that meet the World-wide Fuel Charter should be used whenavailable. Ask
The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fu
Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fuelecon
10. CD: Press and hold untildesired selection is reached.11. Tune / Discs: In radio mode,press to move up or down thefrequency band in individualincre
• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in your vehicle sche
applicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproperly:• Use o
On board diagnostics (OBD-II)Your vehicle is equipped with a computer that monitors the engine’semission control system. This system is commonly known
engine must warm up to its normal operating temperature. Once started,do not turn off the engine until the above driving cycle is complete.CHECKING AN
BRAKE FLUID RESERVOIRThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels below the “M
1. Clean the reservoir cap beforeremoval to prevent dirt and waterfrom entering the reservoir.2. Remove cap and rubberdiaphragm from reservoir.3. Add
4. Latch the gearshift lever in P (Park) and leave the engine running.5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. Ifneces
The transmission fluid should be inthis range if at ambient temperature(10°C-35°C [50°F-95°F]).High fluid levelFluid levels above the safe rangemay re
Checking and adding manual transmission fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Fluid leve
Checking and adding transfer case fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough
CD unit are designed to play commercially pressed 12 cm (4.75 in)audio compact discs only. Due to technical incompatibility, certainrecordable and re-
AIR FILTER MAINTENANCERefer to the scheduled maintenance guide for the appropriate intervalsfor changing the air filter element.When changing the air
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
Tire rotationBecause your vehicle’s tires perform different jobs, they often weardifferently. To make sure your tires wear evenly and last longer, rot
Replacing the tiresReplace the tires when the wearband is visible through the tiretreads. Due to exposure to theelements and exhaust you shouldreplace
tires and chains. If you need to use chains, it is recommended that steelwheels (of the same size and specifications) be used, as chains may chipalumi
REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluidand clutchfluidMotorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to l
Fluid Ford PartNameApplication CapacityPowersteeringfluidMotorcraftMERCON威 ATFAll Fill to between MINand MAX lines onreservoirTransfercase fluidMotorc
3Ensure the correct automatic transmission fluid is used. Transmissionfluid requirements are indicated on the dipstick or on the dipstickhandle. Check
LUBRICANT SPECIFICATIONSItemFord partname orequivalentFord partnumberFordspecificationFront axle(4X4)Motorcraft SAE75W-90Premium 4x4Front AxleLubrican
Treble: Press TREB and then pressSEL to increase/decrease theamount of treble output.2. Select: Press and releaseSEEK/ for previous/nextstrong station
ItemFord partname orequivalentFord partnumberFordspecificationHinges, latches,striker plates,fuel filler doorhinge and seattracks.Multi-PurposeGreaseX
Traction-Lok axles. Add 236 ml (8 oz.) of Additive Friction Modifier XL-3or equivalent meeting Ford specification EST-M2C118-A for completerefill of 1
VEHICLE DIMENSIONSStylesideDimensionBody StyleRegularCab 4x2Regular Cab4x4Super Cab4x2Super Cab4x4(1) Overalllength5256 mm(206.9 in)(SWB)5729 mm(225.5
FlaresideDimensionBody StyleRegularCab 4x2RegularCab 4x4Super Cab4x2Super Cab4x4(1) Overalllength5255 mm(206.9 in)5263 mm(207.2 in)5728 mm(225.5 in)57
14142003 F150 (f12)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specifications264
F-150 SuperCrewDimensionBody StyleSuperCrew 4x2 mm(in)SuperCrew 4x4mm(in)(1) Overall length5738(225.9)5745(226.2)(2) Overall width2009(79.1)12029(79.9
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea
FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford or Ford
Cargo trays (interior)Cellular phone holderDaytime running lights (DRL)Dash trim (wood grain)Engine block heatersManual sliding rear windowPower slidi
6. AUTO: Allows you to set strongradio stations without losing youroriginal manually set preset stations.Select a frequency and press AUTO. Once the s
Protection and appearance equipmentBed mat/bedliner tailgate coversBed matsBedlinersBull bar (chrome & black)Cap (hard, color keyed — Leer supplie
For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle:• When adding accessories,
AAccessory delay ...60Air bag supplemental restraintsystem ...111and child safety seats ..
Cleaning your vehicleengine compartment ...209exterior ...214instrument panel ...212inter
refill capacities ...256service points ...218–220starting after a collision ...177Engine block heater ...
Heatingheating and airconditioning system ...38–40HomeLink universaltransceiver (seeGarage door opener) ...66, 68–69Hood ...
PParking brake ...142Parts (see Motorcraft parts) ...255Pedals (see Poweradjustable foot pedals) ...62Power adju
Tires ...186, 251–252changing ...186–188checking the pressure ...252replacing ...
279
15. Mute: Press to mute the playingmedia.16. Seek: Press to listen to thepreviousor next listenableradio station or CD track.17. CD: Press to enter CD
280
2. Rewind: Press for a slow rewind,press and hold for a fast rewind.Fast forward: Press for a slowadvance, press and hold for a fastadvance.3. Comp (C
Accessories 268Index 272All rights reserved. Reproduction by any means, electronic or mechanicalincluding photocopying, recording or by any informatio
9. Menu: Press MENU and SEL toaccess clock mode, RDS on/off,Traffic, Program type, Show typeand Compression modes.Traffic: Allows you to hear traffic
AUTOSET will flash on the display. When the six strongest stations arefilled, the station stored in preset 1 will begin playing. If there are lessthan
PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD1. Power/volume: Press to turnON/OFF; turnclockwise/counterclockwise toincrease/decrease volume.2. Scan: Press
4. Cassette door: Insert thecassette with the opening to theright.5. Eject: Press to eject thecassette/CD. The radio will resumeplaying.6. Tape: Press
10. Balance: Press BAL; then pressSEL/ to shift sound to theleft/right speakers.Fade: Press FADE; then pressSEL/ to shift sound to therear/front speak
18. Select (SEL): Use with Bass,Treble, Balance, Fade and Clockcontrols.19. Bass: Press BASS; then pressSEL/ to decrease/increasethe bass output.Trebl
1. Mode: Push to toggle betweenAM, FM1, FM2, tape, CD or CDchanger mode (if equipped).2. Memory: Push successively toallow rear seat passengers to scr
• Tighten very loose tapes by inserting a finger or pencil into the holeand turning the hub.• Remove loose labels before inserting tapes.• Allow tapes
HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe
4. Direct the outer instrument panel vents towards the side windowsTo increase airflow to the outer instrument panel vents, close the ventslocated in
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
• Do not put objects under the front seats that will interfere with theairflow to the back seats.• Remove any snow, ice or leaves from the air intake
Temperature conversion: Press the MAX A/C and DEF at thesame time (for one second) to switch between Fahrenheit and Celsius.The English/Metric (E/M) c
8. Vent: Distributes outside air through the instrument panel vents andthe floor vents.9. Max A/C: Distributes recirculated air through the instrument
To aid in side window defogging/demisting in cold weather:1. Select2. Select A/C3. Modulate the temperature control to maintain comfort.4. Set the fan
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola
Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the ON position and• the h
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parklamp operatio
INTERIOR LAMPSMap lampsTo turn on the map lamps, press thecontrol next to each lamp.If equipped with a moon roof, pressthe control next to the map lam
Courtesy/reading lampsThe dome lamp lights when thecontrol is in the DOOR (left)position, any door is open, theinstrument panel switch is pushedpast t
Function Number ofbulbsTrade numberHeadlamps 2 9007Front park/turn lamps 2 3157KFoglamps 2 91451Backup lamp 2 3156KRear stop/turn/sidemarker/taillamp2
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury and prevent possibledamage to others, you
4. Remove bulb retainer ring byturning it counterclockwise, thenslide the ring off the plastic base.5. Carefully pull bulb assembly outof headlamp ass
3. Remove bulb socket from theparking lamp assembly by turning itcounterclockwise.4. Pull bulb straight out of socketand press in the new bulb.Install
Replacing high-mount brake and cargo lamp bulbsMake sure the headlamp control isin the OFF position.1. Remove the two screws and movethe lamp assembly
Replacing running board lamp bulbs (if equipped)The running board bulbs are locatedbehind the running board.1. Reach behind the center bracketof the r
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT STEERING WHEEL (IF EQUIPPED)To adjust the steering wheel:1. Pull and hold the steering wheelrelease control toward you.2. Move the steering wheel
Installing a garage door opener (if equipped)The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers:1. Pl
If the outside temperature falls below 3°C (38°F), the display willalternate from “ICE” to the outside temperature at a two second rate forone minute.
Compass calibration adjustmentPerform this adjustment in an openarea free from steel structures andhigh voltage lines:• Press and hold the SELECTcontr
Auxiliary power point (SuperCrew only)An additional auxiliary power pointis located on the right side rear trimpanel next to the rear seat.CENTER CONS
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
A driver’s first responsibility is the safe operation of the vehicle.The most important thing you can do to prevent a crash is toavoid distractions an
Power rear slider window (if equipped)• Press and hold the open arrowside of control to open window.• Press and hold the closed arrowside of control t
Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog. The mirrors are activatedwhen the vehicle is runn
Never adjust the accelerator and brake pedal with feet on thepedals while the vehicle is moving.SPEED CONTROL (IF EQUIPPED)With speed control set, you
Resuming a set speedPress the RES/RSM (resume)control and release it. This willautomatically return the vehicle tothe previously set speed. TheRES/RSM
• Depress the brake pedal until thedesired vehicle speed is reached,press the SET ACCEL control.Turning off speed controlThere are two ways to turn of
• To tilt into the vent position (when the glass panel is closed), pressand hold the front portion of the moon roof control. To close from thevent pos
also recommended that a new battery be placed in the hand-heldtransmitter of the device being programmed to HomeLink威 for quickertraining and accurate
7. Press and release the “learn” or “smart” button. (The name and colorof the button may vary by manufacturer.)Note: There are 30 seconds in which to
Reprogramming a single HomeLink姞 buttonTo program a device to HomeLink威 using a HomeLink威 button previouslytrained, follow these steps:1. Press and ho
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental Restraint
To record a message:1. Press and release the RECbutton one time to start recording.(An audible tone will sound,confirming the onset of recording).2. P
If the DEL button is inadvertently pressed or the time allotted (fiveseconds) has passed, the indicator light will flash amber and an “error”tone will
TAILGATE REMOVALYour tailgate is removable to allowmore room for loading.1. Lower the tailgate.2. Use a screwdriver to pry thespring clip (on each con
To stow the bed extender, follow steps one through four in reverse order.The bed extender may be used to secure a load of up to 46 kg (100 lbs.)on the
2. Pull the rear corner assist loopsof the cover, outward, then upwardto release the tension. Lift up on therear edge of the cover to remove itfrom th
Flareside only:• Remove two cross bars from pickup box by pushing towards eitherside to release tension.• Lower tailgate, depress the levers on each s
HARD TONNEAU COVER (IF EQUIPPED)The tonneau cover has been designed to maximize fuel economy.• To avoid damage to the cover, donot operate the vehicle
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
Childproof door locks (if equipped)When these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outsi
To open the tonneau cover from theinside, pull the “T” shaped handleand push up on the tonneau coverpanel. The handle is composed of amaterial that wi
Using your vehicle as an ambulanceDo not use this vehicle as an ambulance.Your vehicle is not equipped with the Ford Ambulance PreparationPackage.Noti
Your vehicle is equipped with a remote entry system which allows you to:• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta
The UNLOCK feature will work again after:• a door has become ajar,• the ignition is turned to the ON position, or• using the UNLOCKcontrol on your rem
2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery.4. Insert the new battery. Ref
To reprogram the remote entrytransmitters:1. Ensure the vehicle iselectronically unlocked.2. Put the key in the ignition.3. Turn the key from the 2 (L
The inside lights will not turn off if:• they have been turned on with the dimmer control, or• any door is open.The battery saver will shut off the in
KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• activate or deactivate theaut
The anti-scan feature will turn off after:• one minute of keypad inactivity.• pressing thecontrol on the remote entry transmitter.• the ignition is tu
your vehicle or you can program the keys yourself. Refer toProgramming spare keys for instructions on how to program the codedkey.Note: The SecuriLock
• TheTHEFTindicator will illuminate for three seconds and then goout.• If theTHEFTindicator stays on for an extended period of time orflashes rapidly,
3. Turn the ignition to the 3 (OFF) position.4. Remove the previously programmed coded key from the ignition.5. Within ten seconds of removing the pre
MIDDLE EAST/NORTH AFRICA VEHICLE SPECIFIC INFORMATIONFor your particular global region, your vehicle may be equipped withfeatures and options that are
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Full bench seat (if equipped)• Lift the release bar to move theseat forward or backward. Ensurethat the seat is relatched intoplace.• Pull up on the l
Captain’s chair (if equipped)• Lift the track release bar to movethe seat forward or rearward.Make sure that the seat isrelatched into place.• Pull th
Press to raise or lower the frontportion of the seat cushion.• Type A• Type BPress to raise or lower the rearportion of the seat cushion.• Type A• Typ
Press the control to move the seatforward, backward, up or down.• Type A• Type BHeated seats (if equipped)To operate the heated seats:• Push control l
Returning the seat to seating positionAlways be sure that the seat is in a latched position, whether theseat is occupied or empty. If not latched, the
3. Pull seatback toward front seatand down into load floor position.4. Make sure seat is pushed all theway down and locks into position.Returning the
2. Lift seatback up until it locks intovertical position.3. Return the head restraint to its original position.If the head restraint is insertedbackwa
SAFETY RESTRAINTSSafety restraints precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce
Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Checkseat covers and buckle
Commentaires sur ces manuels