Introduction 4Instrument Cluster 12Warning and control lights 12Gauges 16Entertainment Systems 20AM/FM stereo cassette 20AM/FM stereo with CD 23AM/FM
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Checkseat covers and buckle
• Front seats• Rear seats (if equipped)The front and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front p
When to use the automatic locking mode• Anytime a child safety seat is installed in a passenger front oroutboard rear seating position with Regular Ca
2. Grasp the shoulder portion andpull downward until the entire beltis extracted.3. Allow the belt to retract. As the belt retracts, you will hear a c
CrewCab base bench seats and all Regular Cab seating positions, thesafety belts are equipped with a retractor pretensioner.The driver and front outboa
• 4–door SuperCab (Bench seatsonly)To lower the shoulder belt height, push the button and slide the heightadjuster down. To raise the height of the sh
Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war
The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to infla
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle.BeltMinder activation and deactivation proce
Safety belt extension assemblyIf the safety belt is too short when fully extended, there is a 20 cm (8inch) safety belt extension assembly that can be
AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and righ
The National Highway Traffic Safety Administration (NHTSA)recommends a minimum distance of at least 25 cm (10 inches)between an occupant’s chest and t
Children must always be properly restrained. Failure to follow theseinstructions may increase the risk of injury in a collision.An infant in a rear-fa
internal injuries, particularly to occupants who are not properlyrestrained or are otherwise out of position at the time of air bagdeployment. Thus, i
A difficulty with the system is indicated by one or more of the following:• The readiness lights will eitherflash or stay lit.• The readiness lights w
Turning the passenger air bag off1. Insert the ignition key, turn theswitch to OFF position and hold inOFF position while removing thekey.2. When the
Turning the passenger air bag back onThe passenger air bag remains OFF until you turn it back ON.1. Insert the ignition key and turnthe switch to ON.2
Always transport children who are 12 and younger in the rearseat. Always use safety belts and child restraints properly. If achild in a rear facing in
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterHarley—Davidson instrument clusterWarning lights and gauges can alert y
• the child has a medical condition which, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the dr
Important child restraint precautionsYou are required by law to use safety restraints for children in the U.S.and Canada. If small children (generally
Booster seats position a child so that safety belts fit better. They lift thechild up so that the lap belt rests low across the hips and the kneesbend
• Those with a high back.If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo
SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully fo
• Put the safety belt in the automatic locking mode. Refer to Automaticlocking mode (passenger side front and outboard rear seatingpositions-Regular C
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a
Installing child safety seats in the front row lap belt seatingpositions1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that itsbot
7. Allow the safety belt to retract to remove any slack in the belt. It willmake a clicking noise while doing this.8. Before placing the child in the
Many lights will illuminate when you start your vehicle to make sure thebulb works. If any light remains on after starting the vehicle, have therespec
• F150 Regular Cab• F150 SuperCab• F150 SuperCrew• F150 SuperCrew with quad bucketsTether strap attachment1. Position the child safety seat on the sea
• You may need to pull the seatback forward to access the tetheranchors. Make sure the seatback is locked in the upright positionbefore installing the
• Rear seats (SuperCrew only)If the tether strap is clippedincorrectly, the child safetyseat may not be retained properlyin the event of a collision.5
1. Route the tether strap throughthe loop directly behind the childseat.2. Attach the strap hook onto theloop behind an adjacent seatingposition.3. In
Your vehicle may be equipped with LATCH anchors for child seatinstallation at the following seating positions:• F150 Regular Cab• F150 Supercab• F150
seat. If you install a child seat at the center rear position, use the vehiclelap belt and the top tether anchor.Connectors on the LATCH child seatand
STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
• Make sure the gearshift is in P(Park).If starting a vehicle with a manualtransmission:1. Make sure the parking brake isset.2. Push the clutch pedal
Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced.• If the driver’s safety
Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance mayoccur. It will take you longer
Using the engine block heater (if equipped)An engine block heater warms the engine coolant which aids in startingand heater/defroster performance. Use
Using ABSWhen hard braking is required, apply continuous force on the brakepedal; do not pump the brake pedal since this will reduce theeffectiveness
Always set the parking brake fully and make sure that thegearshift is securely latched in P (Park) (automatictransmission) or in 1 (First) (manual tra
Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.
Do not drive your vehicle until you verify that the brakelampsare working.Always set the parking brake fully and make sure the gearshift islatched in
N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.(O
Forced downshifts• Allowed in(Overdrive) or Drive.• Depress the accelerator to the floor.• Allows transmission to select an appropriate gear.Shift str
To start the vehicle:1. Make sure the parking brake is fully set.2. Press the clutch pedal to the floor, then put the gearshift lever in theneutral po
4.6L V8 engine (4x2 and 4x4 with 3.08:1 rear axle ratio)Upshifts when accelerating (recommended for best fueleconomy)Shift from: Transfer case positio
Upshifts when cruising (recommended for best fuel economy)Shift from: Transfer case position (if equipped)2H or 4H 4L1 - 2 16 km/h (10 mph) 6 km/h (4
Low fuel: Illuminates when the fuellevel in the fuel tank is at, or nearempty (refer to Fuel gauge in thischapter).Low washer fluid: Illuminateswhen t
Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brakefully.Removing the keyTur
Using a manual 4WD system (if equipped)2H (2WD High) – Power to the rear wheels only; used for street andhighway driving. Provides optimal smoothness
4. Move the transfer case lever through N (Neutral) directly to thedesired position. The LOW RANGE indicator will illuminate once thetransfer case has
Shifting between 2H (2WD High) and 4H (4WD High)• Move the 4WD control between 2H and 4H at any forward speed up to88 km/h (55 mph).Note: Do not perfo
Drive cautiously to avoid vehicle damage from concealed objects such asrocks and stumps.You should either know the terrain or examine maps of the area
If your vehicle gets stuckIf your vehicle gets stuck in mud or snow it may be rocked out byshifting between forward and reverse gears, stopping betwee
Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.
Normal characteristicsOn some 4WD models, the initial shift from two-wheel drive to 4x4 whilethe vehicle is moving can cause some momentary clunk and
Driving through deep water may damage the transmission.If the front or rear axle is submerged in water, the axle lubricant shouldbe replaced.After dri
Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;
High beams: Illuminates when thehigh beam headlamps are turned on.Key-in-ignition warning chime: Sounds when the key is left in theignition in the OFF
Never drive with chains on the front tires of 4WD vehicles without alsoputting them on the rear tires. This could cause the rear to slide andswing aro
Each day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires, and adjust ifrequired.
DRIVING THROUGH WATERIf driving through deep or standing water is unavoidable, proceed veryslowly especially if the depth is not known. Never drive th
engine/transmission combination, any required option weight for trailertowing and the weight of the driver from the GCWR for the towingvehicle.• Maxim
Your vehicle can haul more cargo and people than most passenger cars.Depending upon the type and placement of the load, hauling cargo andpeople may ra
Engine Rear axle ratio MaximumGCWR-kg(lbs.)Maximumtrailerweight-kg (lbs.)Regular Cab 4x2 w/automatic transmission4.2L 3.31 4077 (9000) 2132 (4700)4.2L
Engine Rear axle ratio MaximumGCWR-kg (lbs.)Maximumtrailerweight-kg (lbs.)SuperCab 4x2 w/manual transmission4.2L 3.08 2944 (6500) 907 (2000)4.2L 3.55
Engine Rear axle ratio Maximum GCWR-kg(lbs.)Maximumtrailer weight -kg (lbs.)Regular Cab 4x4 w/manual transmission4.2L 3.31 3265 (7200) 1179 (2600)4.2L
Load equalizing hitchWhen hooking up a trailer using a load equalizing hitch, always use thefollowing procedure:1. Park the unloaded vehicle on a leve
Using a step bumper (if equipped)The rear bumper is equipped with an integral hitch and only requires aball with a 25.4 mm (one inch) shank diameter.
Harley—Davidson instrument cluster gaugesSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemp
Launching or retrieving a boatDisconnect the wiring to the trailer before backing the trailerinto the water. Reconnect the wiring to the trailer after
SNOWPLOWINGFord recommends the following specifications for low speed, personaluse snow removal:• F-150 4x4 (except F-150 Supercrew, Lightning and Har
• Federal and most local regulations require additional exterior lampsfor snowplow-equipped vehicles. Consult your dealer for additionalinformation.•
Do not attempt to service, repair, or modify the Air BagSupplemental Restraint System or its fuses. See your Ford orLincoln Mercury dealer.Additional
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
This switch is located in the frontpassenger’s footwell, by the kickpanel access cover.To reset the switch:1. Turn the ignition OFF.2. Check the fuel
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 15A Audio2 5A Powertrain Control Module(PC
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description7 — Not used8 5A Radio, Remote entry module,GEM, In-vehicle entertainmentsy
Trip odometer: Registers thekilometers (miles) of individualjourneys. Press the control once toswitch from the odometer to thetrip odometer. To reset
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description23 10A Trailer tow battery Charge relay,Turn/Hazard flasher, 4x4solenoids,
Always replace the cover to the power distribution box beforereconnecting the battery or refilling fluid reservoirsIf the battery has been disconnecte
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription8 15A* Power door locks, CentralSecurity Module (CSM), Lockrelays (not used on SuperC
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription102 50/20A** Four-wheel Anti-lock BrakeSystem (4WABS)module/Rear-wheel Anti-lockBrake
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription206 — Fog lamp relay207 — Front washer pump relay208 — Intercooler pump relay(superch
Spare tire informationYour vehicle is equipped with a spare tire that may be used as a spare ora regular tire. The spare tire wheel may not match the
2. Attach the spare tire lock key (A)to the jack handle (B).3. Fully insert the jack handlethrough the bumper hole and intothe guide tube. The key and
1. Park on a level surface, activatehazard flashers and set the parkingbrake.2. Place gearshift lever in P (Park)(automatic transmission) or in therev
When one of the rear wheels is off the ground, the transmissionalone will not prevent the vehicle from moving or slipping off thejack, even if the tra
• RearTo lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engine when yourve
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe
• Seven lug nut wheel12. Stow the flat tire. Refer to Stowing the flat/spare tire.13. Stow the jack and lug wrench. Make sure the jack is fastened so
ratchets or slips with little effort, take the vehicle to your dealer forassistance at your earliest convenience.4. Check that the tire lies flat agai
4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level.5. Tu
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeFord Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
Locks and Security 78Keys 78Locks 78Anti-theft system 81Seating and Safety Restraints 91Seating 91Safety restraints 99Air bags 112Child restraints 120
AM/FM STEREO CASSETTE1. Balance: Press to shift sound tothe left/right speakers.2. Fade: Press to shift sound to therear/front speakers.3. CLK: To set
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai
Board membershipThe Board consists of:• Three consumer representatives• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa
Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADAONLY)In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a
If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest F
IN CALIFORNIA (U.S. ONLY)California Civil Code Section 1793.2(d) requires that, if a manufactureror its representative is unable to repair a motor veh
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam
• 4.2L V6 engine• 4.6L V8 and 5.4L V8 engineCleaning209
4. Tape AMS: In tape mode, pressand hold to activate AutomaticMusic Search (allows you to quicklylocate the beginning of the tape selection being play
• 5.4L Supercharged V8 engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTIC (NON-P
INSTRUMENT PANEL AND CLUSTER LENSClean the instrument panel with a damp cloth, then dry with a dry cloth.• Avoid cleaners or polish that increase the
LEATHER SEATS (IF EQUIPPED, EXCEPT FOR THE KING RANCHSUPERCREW)Your leather seating surfaces have a clear, protective coating over theleather.For King
SCRATCHESIn order to lessen the appearance of certain scratches and other wearmarks, apply conditioner on the affected area following the sameinstruct
FORD, LINCOLN AND MERCURY CAR CARE PRODUCTSYour Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect i
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
Working with the engine on• Automatic transmission:1. Set the parking brake and shift to P (Park).2. Block the wheels.• Manual transmission:1. Set the
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.2L V6 engine1. Battery2. Engine oil filler cap3. Engine oil dipstick4. Clutch fluid reservoir (manua
4.6L V8/5.4L V8 engines1. Power steering fluid reservoir2. Clutch fluid reservoir (manual transmission)3. Engine oil dipstick4. Brake fluid reservoir5
5.4L Supercharged V8 engine1. Engine oil dipstick2. Power steering fluid reservoir3. Brake fluid reservoir4. Power distribution box5. Engine coolant r
12. Power/volume: Press to turnON/OFF; turn to increase ordecrease volume levels.13. AM/FM: Press to choose afrequency band in radio mode.14. Bass: Pr
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
• 4.2L engine• 4.6L/5.4L engineMaintenance and Specifications221
5. Locate and carefully remove the engine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.
Engine oil and filter recommendationsLook for this certificationtrademark.SAE 5W-20 engine oil is recommended.Only use oils “Certified For Gasoline En
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “cold fill level” or within the “c
Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant couldmake it difficult to see through
1. Before you begin, turn the engine off and let it cool.2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the c
AM/FM STEREO / SINGLE CD RADIO1. Balance: Press/ to shiftsound to the left/right speakers.2. Fade: Press/ to shiftsound to the front/rear speakers.3.
Coolant refill capacityTo find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in this chapter.Fill your engine c
How fail-safe cooling worksIf the engine begins to overheat:• The engine coolant temperaturegauge will move to the red (hot)area.• Theand the symbolwi
5. Restart the engine and take your vehicle to a service facility.Driving the vehicle without repairing the engine problemincreases the chance of engi
• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kindcan lead to eye and respiratory tract irritation. In severe cases,excessive or p
Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1/8 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref
Repairs to correct the effects of using a fuel for which your vehicle wasnot designed may not be covered by your warranty.Octane recommendationsYour v
and emission control system protection for your vehicle. Gasolines thatmeet the World-wide Fuel Charter should be used when available. Askyour fuel su
The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fu
Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fuelecon
• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in your vehicle sche
5. EJ (eject): Press to eject a CD.6. COMP (Compression): In CDmode, press to bring louder andsofter levels into more comfortablelistening level. The
applicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproperly:• Use o
On board diagnostics (OBD-II)Your vehicle is equipped with a computer that monitors the engine’semission control system. This system is commonly known
engine must warm up to its normal operating temperature. Once started,do not turn off the engine until the above driving cycle is complete.CHECKING AN
BRAKE FLUID RESERVOIRThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels below the “M
1. Clean the reservoir cap beforeremoval to prevent dirt and waterfrom entering the reservoir.2. Remove cap and rubberdiaphragm from reservoir.3. Add
4. Latch the gearshift lever in P (Park) and leave the engine running.5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. Ifneces
The transmission fluid should be inthis range if at ambient temperature(10°C-35°C [50°F-95°F]).High fluid levelFluid levels above the safe rangemay re
Checking and adding manual transmission fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Fluid leve
Checking and adding transfer case fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough
AIR FILTER MAINTENANCERefer to the scheduled maintenance guide for the appropriate intervalsfor changing the air filter element.When changing the air
15. AM/FM: Press to choose afrequency band in radio mode.16. Bass: Press/ toincrease/decrease the bass output.17. Treble: Press/ toincrease/decrease t
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
Tire rotationBecause your vehicle’s tires perform different jobs, they often weardifferently. To make sure your tires wear evenly and last longer, rot
Replacing the tiresReplace the tires when the wearband is visible through the tiretreads. Due to exposure to theelements and exhaust you shouldreplace
Follow these guidelines when using snow tires and chains:• Use only SAE Class S chains.• Install chains securely, verifying that the chains do not tou
REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluidand clutchfluidMotorcraftHighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to li
Fluid Ford PartNameApplication CapacityFuel tank N/A 4x4 Reg. Cab withshort wheelbase92.7L (24.5 gallons)4x2 Regular Cab,SuperCab andSuperCrew withsho
Fluid Ford PartNameApplication CapacityRear axle5MotorcraftSAE 75W-140Synthetic RearAxle Lubricant10.25 inch axle 3.3L (6.9 pints)7Windshieldwasher fl
axle assembly has been submerged in water. The axle lubricant shouldbe changed any time the rear axle has been submerged in water.6Service refill capa
ItemFord part nameor equivalentFord partnumberFordspecificationEngine coolant MotorcraftPremium GoldEngine Coolant(yellow-colored)VC-7–A WSS- M97B51-A
PREMIUM AM/FM STEREO/SINGLE CD RADIO1. Bass: Press BASS and the pressSEL to increase/decrease theamount of bass output.Treble: Press TREB and then pre
ItemFord part nameor equivalentFord partnumberFordspecificationAutomatictransmission(4R100)2MotorcraftMERCON威 ATFXT-2-QDX MERCON威Automatictransmission
ENGINE DATAEngine4.2L V6engine4.6L V8engine5.4L V8engine5.4LSuperchargedV8 engineCubicinches256 281 330 330Requiredfuel87 octane 87 octane 87 octane 9
DimensionBody StyleRegularCab 4x2Regular Cab4x4Super Cab4x2Super Cab4x4(3) Overallheight1846 mm(72.7 in)(SWB)1838 mm(72.4 in)(LWB)1915 mm(75.4 in)(SWB
25314Maintenance and Specifications263
F-150 SuperCrewDimensionBody StyleSuperCrew 4x2 mm(in)SuperCrew 4x4mm(in)(1) Overall length5738(225.9)5745(226.2)(2) Overall width2009(79.1)12029(79.9
25314Maintenance and Specifications265
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
7. Assembly plant8. Production sequence numberEngine numberThe engine number (the last eight numbers of the vehicle identificationnumber) is stamped o
FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincol
Cargo trays (interior)Cellular phone holderDaytime running lights (DRL)Dash trim (wood grain)Engine block heatersManual sliding rear windowPower slidi
Fade: Press FADE then press SELto shift the sound from thefront/rear speakers.4. Eject: Press to eject a CD.5. RDS: Allows your audio systemto receive
Protection and appearance equipmentBed mat/bedliner tailgate coversBed matsBedlinersBull bar (chrome & black)Cap (hard, color keyed — Leer supplie
For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle:• When adding accessories,
AAccessory delay ...61Air bag supplemental restraintsystem ...112and child safety seats ..
Cleaning your vehicleengine compartment ...208exterior ...213instrument panel ...211inter
lubricationspecifications ...258, 261refill capacities ...255service points ...217–219starting afte
high beam ...46replacing bulbs ...50turning on and off ...45Heatingheating and ai
Moon roof ...66Motorcraft parts ...236, 254OOctane rating ...235Oil (see Engine
StereoSingle CD ...23TTailgate ...72–73Tilt steering wheel ...56Tires
278
279
9. Fast forward: Press to advanceon the CD. Press and hold for amore fast advance.10. Rewind: Press for a slowrewind. Press and hold for a fastrewind.
280
PREMIUM IN-DASH SIX CD SOUND SYSTEM1. Seek: Press and releaseSEEK/ for previous/nextstrong station, or track of currentdisc.2. Rewind: Press for a slo
Maintenance and Specifications 215Engine compartment 217Engine oil 220Battery 224Fuel information 232Air filter(s) 249Part numbers 254Refill capacitie
6. Bass: Press BASS; then pressSEL/ to decrease/increasethe bass output.Treble: Press TREB; then pressSEL/ to decrease/increasethe treble output.7. Se
10. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, press andhold a preset button until soundreturns. In CD mode, pres
17. Disc/Tune: Radio: Pressor to manually tune down or upthe frequency band.CD: Pressor to select the previous or next track on the CD.18. CD door: In
for five seconds, then moves to the next station. Press again to stop.Tape/CD: Press SCAN to sample tape/CD selections for eight seconds.Press again t
9. CLOCK: Press the CLK controluntil SELECT HOUR is displayedthen press SELto decrease thehours orto increase the hours.To set the minute, press CLKco
16. Fast Forward (FF): Press tofast forward the tape.17. Rewind (REW): Press torewind the tape.18. Select (SEL): Use with Bass,Treble, Balance, Fade a
REAR AUDIO CONTROLS (IF EQUIPPED)The rear seat controls allow the rear seat passengers to operate theradio, tape, CD or CD changer or in-vehicle enter
RADIO RECEPTION FACTORSThere are three factors that can effect radio reception:• Distance/strength: The further you travel from an FM station, theweak
CD units are designed to play commercially pressed 12 cm (4.75in) audio compact discs only. Due to technical incompatibility,certain recordable and re
HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
To aid in side window defogging/demisting in cold weather:1. Select2. Set the temperature control to full heat3. Set the fan speed to HI4. Direct the
OPERATING TIPS• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (EATC)SYSTEMTemperature conversion: Press the MAX A/C and DEFat thesame time (for one second) to switch betwe
3. Fan speed: Turn to manuallyincrease or decrease fan speed.4. Defrost:Distributes outside air through the windshield defrostervents.5. Floor/defrost
OPERATING TIPS• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola
Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the ON position and• the h
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parklamp operatio
INTERIOR LAMPSMap lampsTo turn on the map lamps, press thecontrol next to each lamp.If equipped with a moon roof, pressthe control next to the map lam
Courtesy/reading lampsThe dome lamp lights when thecontrol is in the DOOR (left)position, any door is open, theinstrument panel switch is pushedpast t
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury and prevent possibledamage to others, you
Function Number ofbulbsTrade numberHeadlamps 2 9007Front park/turn lamps 2 3157AK (amber)Foglamps 2 91451Backup lamp 2 3156KRear stop/turn/sidemarker/
4. Remove bulb retainer ring byturning it counterclockwise, thenslide the ring off the plastic base.5. Carefully pull bulb assembly outof headlamp ass
3. Remove bulb socket from theparking lamp assembly by turning itcounterclockwise.4. Pull bulb straight out of socketand press in the new bulb.Install
Replacing high-mount brake and cargo lamp bulbsMake sure the headlamp control isin the OFF position.1. Remove the two screws and movethe lamp assembly
3. Pull out the old bulb from the socket and push in the new bulb.4. Install the bulb socket in lamp assembly by turning it clockwise.Replacing runnin
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT STEERING WHEEL (IF EQUIPPED)To adjust the steering wheel:1. Pull and hold the steering wheelrelease control toward you.2. Move the steering wheel
Installing a garage door opener (if equipped)The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers:1. Pl
If the outside temperature falls below 3°C (38°F), the display willalternate from “ICE” to the outside temperature at a two second rate forone minute.
Compass calibration adjustmentPerform this adjustment in an openarea free from steel structures andhigh voltage lines:• Press and hold the SELECTcontr
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
Auxiliary power point (SuperCrew only)An additional auxiliary power pointis located on the right side rear trimpanel next to the rear seat.CENTER CONS
A driver’s first responsibility is the safe operation of the vehicle.The most important thing you can do to prevent a crash is toavoid distractions an
Power rear slider window (if equipped)• Press and hold the open arrowside of control to open window.• Press and hold the closed arrowside of control t
Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog. The mirrors are activatedwhen the vehicle is runn
Never adjust the accelerator and brake pedal with feet on thepedals while the vehicle is moving.SPEED CONTROL (IF EQUIPPED)With speed control set, you
Resuming a set speedPress the RES/RSM (resume)control and release it. This willautomatically return the vehicle tothe previously set speed. TheRES/RSM
• Depress the brake pedal until thedesired vehicle speed is reached,press the SET ACCEL control.Turning off speed controlThere are two ways to turn of
• To tilt into the vent position (when the glass panel is closed), pressand hold the front portion of the moon roof control. To close from thevent pos
also recommended that a new battery be placed in the hand-heldtransmitter of the device being programmed to HomeLink威 for quickertraining and accurate
7. Press and release the “learn” or “smart” button. (The name and colorof the button may vary by manufacturer.)Note: There are 30 seconds in which to
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental Restraint
Reprogramming a single HomeLink姞 buttonTo program a device to HomeLink威 using a HomeLink威 button previouslytrained, follow these steps:1. Press and ho
To record a message:1. Press and release the RECbutton one time to start recording.(An audible tone will sound,confirming the onset of recording).2. P
If the DEL button is inadvertently pressed or the time allotted (fiveseconds) has passed, the indicator light will flash amber and an “error”tone will
TAILGATE REMOVALYour tailgate is removable to allowmore room for loading.1. Lower the tailgate.2. Use a screwdriver to pry thespring clip (on each con
To stow the bed extender, follow steps one through four in reverse order.The bed extender may be used to secure a load of up to 46 kg (100 lbs.)on the
2. Pull the rear corner assist loopsof the cover, outward, then upwardto release the tension. Lift up on therear edge of the cover to remove itfrom th
Flareside only:• Remove two cross bars from pickup box by pushing towards eitherside to release tension.• Lower tailgate, depress the levers on each s
HARD TONNEAU COVER (IF EQUIPPED)The tonneau cover has been designed to maximize fuel economy.• To avoid damage to the cover, donot operate the vehicle
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
Childproof door locks (if equipped)When these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outsi
F150 SuperCrew, F150 5.4L Supercharged “Lightning” andHarley-Davidson F-150 Owners: SnowplowingYour vehicle is not recommended for snowplowing. Ford m
To open the tonneau cover from theinside, pull the “T” shaped handleand push up on the tonneau coverpanel. The handle is composed of amaterial that wi
Your vehicle is equipped with a remote entry system which allows you to:• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta
The UNLOCK feature will work again after:• a door has become ajar,• the ignition is turned to the ON position, or• using the UNLOCKcontrol on your rem
Replacing lost remote entry transmittersIf you would like to have your remote entry transmitter reprogrammedbecause you lost one, or would like to buy
The illuminated entry system will turn off the interior lights if:• the ignition switch is turned to the ON position, or• the remote transmitter lock
7. Turn the ignition to OFF. The horn will chirp once to confirm theprocedure is complete.KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless en
Anti-scan featureIf the wrong code has been entered 36 times, the keypad will go into ananti-scan mode. This mode disables the keypad for one minute a
SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEMSecuriLock娂 passive anti-theft system is an engine immobilizationsystem. This system is designed to prevent the e
Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 3(OFF) position.TheTHEFTindicator will flashevery two seconds when
• If two previously programmed coded keys are not available, you musttake your vehicle to your dealer to have the spare key(s)programmed.1. Insert a p
Notice to owners of the Harley-Davidson F-150Note: Your vehicle is not designed to be operated off-road.The undercab chrome bars are for decorative pu
If the key was not successfully programmed, it will not start yourvehicle’s engine and the theft indicator light will flash on and off, or stayon for
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Full bench seat (if equipped)• Lift the release bar to move theseat forward or backward. Ensurethat the seat is relatched intoplace.• Pull up on the l
Captain’s chair (if equipped)• Lift the track release bar to movethe seat forward or rearward.Make sure that the seat isrelatched into place.• Pull th
Press to raise or lower the frontportion of the seat cushion.• Type A• Type BPress to raise or lower the rearportion of the seat cushion.• Type A• Typ
Press the control to move the seatforward, backward, up or down.• Type A• Type BHeated seats (if equipped)To operate the heated seats:• Push control l
Returning the seat to seating positionAlways be sure that the seat is in a latched position, whether theseat is occupied or empty. If not latched, the
3. Pull seatback toward front seatand down into load floor position.4. Make sure seat is pushed all theway down and locks into position.Returning the
2. Lift seatback up until it locks intovertical position.3. Return the head restraint to its original position.If the head restraint is insertedbackwa
SAFETY RESTRAINTSSafety restraints precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce
Commentaires sur ces manuels