Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Message center 19Entertainment Systems 32Auxiliary input jack (Line in) 42USB
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
To open the moon roof: Press andrelease the SLIDE control, the moonroof will open automatically. Pressthe switch again to stop the moonroof.WARNING: W
POWER REAR SUNSHADE (IF EQUIPPED)Your vehicle may be equipped with apower rear sunshade that covers therear window of your vehicle. Thecontrol is loca
model manufactured before April 1, 1982). A garage door which cannotdetect an object, signaling the door to stop and reverse, does not meetcurrent U.S
6 to complete programming of a rolling code equipped device (mostcommonly a garage door opener).4. At the garage door opener receiver (motor-head unit
Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet
POSITIVE RETENTION FLOOR MATWARNING: Always usefloor mats that are designedto fit the foot well of your vehicle.Only use floor mats that leave thepeda
TRUNK RELEASETo open the trunk from insidethe vehicle:Press the trunk release buttonlocated on the instrument panelnear the radio.To open the trunk wi
KEYSIntegrated keyhead transmitters (IKTs) (if equipped)Your vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade is u
Intelligent Access Key (IA key) (if equipped)Your vehicle may be equipped withtwo intelligent access keys whichoperate the power locks and theremote e
MYKEY姞The MyKey威 feature allows you to program a restricted driving mode topromote good driving habits. All but one of the keys programmed to thevehic
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
Create a MyKey威To program MyKey威 on one of the keys programmed to the vehicle,insert the key that you want to make a MyKey威 into the ignition. Forvehi
5. Press SETUP to enter your choice. The next optional setting will bedisplayed.6. Repeat Steps 4 and 5 until you are done changing the optionalsettin
Vehicles equipped with traditional keys:When using a Ford-approved remote start system, the default settingswill recognize the remote start system as
TroubleshootingCondition Potential CausesCan’t create a MyKey威 • Key in the ignition is already aMyKey威.• Key in the ignition is the lastremaining adm
Condition Potential CausesLost the only admin key • Purchase a new key from yourauthorized dealer.Lost any key • For programming spare keys, referto t
POWER DOOR LOCKS• Press thecontrol to unlock alldoors.• Press thecontrol to lock alldoors.Smart unlocksThis feature helps to prevent you from locking
automatically be released when you attempt to close it, and the horn willchirp, as a reminder that the IA key is inside. If you would like tointention
Note: The autolock feature can be activated/deactivated independentlyof the autounlock feature.Power door lock switch autolock enable/disable procedur
Deactivating/activating autounlock featureYour vehicle comes with the autounlock feature activated; there are threemethods to enable/disable this feat
CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the
WARNING LIGHTS AND CHIMESStandard instrument cluster shown, optional cluster similarWarning lights and gauges can alert you to a vehicle condition tha
To open the luggage compartmentdoor (lid) from within the luggagecompartment, pull the illuminated“T” shaped handle and push up onthe trunk lid. The h
REMOTE ENTRY SYSTEMThe intelligent access keys (IA key) comply with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject
Intelligent access (if equipped)Your vehicle will allow you to unlock and enter your vehicle withoutactively using a key or transmitter. You can use t
2. Press and release again within three seconds to unlock all thedoors. The turn signals will flash.The remote entry system activates the illuminated
Sounding a panic alarmPressto activate the alarm. The horn will sound and the turn lampswill flash for a maximum of three minutes. Press again or turn
• Vertically mounted• Horizontally mounted2. Press and hold button 1 for five seconds. A tone will be heard aftertwo seconds confirming memory positio
Integrated keyhead transmitter (IKT)To replace the battery:1. Twist a thin coin in the slot nearthe key ring to remove the batterycover (1).Note: Do n
2. Remove the old battery.Note: Please refer to localregulations when disposing oftransmitter batteries.3. Insert the new battery. Refer tothe instruc
The lights will not turn off if:• they have been turned on with the dimmer control, or• any door is open.Illuminated exitWhen all vehicle doors are cl
SECURICODE™ KEYLESS ENTRY SYSTEMThe keypad, located near the driver’s window, is invisible until touchedand then it lights up so you can see and touch
Solid illumination after the engine is started indicates the on-boarddiagnostics system (OBD-II) has detected a malfunction. Refer toOn-board diagnost
Note: Touching 5 • 6, 7 • 8, or 9 • 0 keypad numbers as a sixth digitwill not recall a driver memory setting.Note: The factory-set code cannot be asso
Note: If equipped with intelligent access, if the intelligent access key iswithin 3 feet (1 meter) of the driver door, your keyless entry keypadcode w
Anti-theft indicatorThe anti-theft indicator is located in the instrument panel cluster.• When the ignition is off, theindicator will flash once every
The integrated keyhead transmitter (IKT) functions as both aprogrammed ignition key that operates all the locks and starts thevehicle, as well as a re
2. Turn the ignition from off to on. Keep the ignition on for at least threeseconds, but no more than 10 seconds.3. Turn the ignition off and remove t
programmed to your vehicle, you must take your vehicle and all accesskeys to your authorized dealer to be erased and reprogrammed.Ensure that the vehi
PERIMETER ALARM SYSTEM (IF EQUIPPED)The perimeter alarm system will help protect your vehicle fromunauthorized entry.When the following types of unaut
Disarming the systemTo disarm the system, do any of the following:• Unlock the doors by pressing unlockon the remote entrytransmitter.• Unlock the doo
FRONT SEATSWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the eve
The adjustable head restraintsconsist of:• a trimmed energy absorbing foamand structure (1),• two steel stems (2),• a guide sleeve adjust/releasebutto
Airbag readiness: If this light failsto illuminate when the ignition isturned to on, continues to flash orremains on, have the systemserviced immediat
WARNING: The adjustable head restraint is a safety device.Whenever possible it should be installed and properly adjustedwhen the seat is occupied.To r
Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as possible to theba
Lift handle to move seat forward orbackward.Pull lever up to adjust seatback.WARNING: Beforereturning the seatback to itsoriginal position, make sure
Adjusting the front power seat (if equipped)WARNING: Never adjust the driver’s seat or seatback when thevehicle is moving.WARNING: Do not pile cargo h
Use the control to tilt the seat.Use the control to move the seatforward, backward, up or down.Use the control to recline theseatback forward or rearw
• Continue pressing the control for approximately two seconds; you willfeel the seat bounce back slightly.Using the power lumbar support (if equipped)
Press either up or down on thelumbar control to select the top,middle, or bottom part of the seatback.Push and hold the front of thelumbar control to
Note: Do not do the following:• Place heavy objects on the seat• Operate the seat heater if water or any other liquid is spilled on theseat. Allow the
Cooled seatsThe cooled seats will only function when the engine is running.To operate the cooled seats:Press the cooled seat symbol/buttonto cycle thr
To remove an air filter:1. Turn the vehicle off.2. Push up on the outside rigid edgeof the filter until the tabs arereleased, then rotate the air filt
Low fuel (RTT): Illuminates whenthe fuel level in the fuel tank is ator near empty. Refer to Fuel gaugein this chapter.Low washer fluid (RTT):Illumina
Memory seats/power mirrors/adjustable pedals (if equipped)This system allows automatic positioning of the driver seat, powermirrors, and adjustable pe
Easy entry/exit feature (if equipped)This feature automatically moves the driver’s seat rearward 2 in. (5 cm)when:• the transmission is in N (Neutral)
To remove the non-adjustable head restraint, do the following:1. Simultaneously press and holdboth unlock/remove buttons, thenpull up on the head rest
The adjustable head restraintconsist of :• a trimmed energy absorbing foamand structure (1),• two steel stems (2),• a guide sleeve adjust/releasebutto
To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous
WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Split-folding rear seatOne or both rea
Seat-mounted cup holders and armrest storage compartment(if equipped)If your vehicle is equipped with cup holders and a storage compartment,they are l
The heated seats only operate when the ignition is on. To operate theheated seats:• Press the indicated side of thecontrol for maximum heat.• Press ag
• Restraints Control Module (RCM) with impact and safing sensors.• Restraint system warning light and back-up tone.• The electrical wiring for the air
Driver’s seat position sensorThe driver’s seat position sensor allows your Personal Safety System totailor the deployment level of the driver dual-sta
Low tire pressure warning:Illuminates when your tire pressureis low. If the light remains on atstart up or while driving, the tirepressure should be c
Front safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly ag
WARNING: To reduce the risk of injury, make sure children sitwhere they can be properly restrained.WARNING: Never let a passenger hold a child on his
WARNING: Front and rear seat occupants, including pregnantwomen, should wear safety belts for optimum protection in anaccident.Combination lap and sho
Pregnant women should alwayswear their safety belt. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips
How to use the automatic locking mode1. Buckle the combination lap andshoulder belt.2. Grasp the shoulder portion andpull downward until the entire be
Energy management feature — front outboard• This vehicle has a safety belt system with an energy managementfeature at the front seats to help further
Safety belt height adjustmentYour vehicle has safety belt heightadjustments for the front outboardseating positions.Adjust the height of the shoulderb
Belt-Minder姞The Belt-Minder威 feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders byinterm
If... Then...The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately1 minute while the vehicle istraveling at least 3 mph(5 km
Reasons given... Consider...“Traffic is light” Nearly 1 of 2 deaths occur insingle-vehicle crashes, many whenno other vehicles are around.“Belts wrink
High beams: Illuminates when thehigh beam headlamps are turned on.Heads up display (if equipped):A red bar will illuminate on thewindshield in certain
Note: If you are using MyKey威, the Belt-Minder威 cannot be disabled.Also, if the Belt-Minder威 has been previously disabled, it will bere-enabled during
• This will enable the Belt-Minder威 feature for that seating position if itis currently disabled. As confirmation, the safety belt warning light willf
Important supplemental restraint system precautionsAirbags DO NOT inflate slowly orgently and the risk of injury from adeploying airbag is greatest cl
WARNING: Do not put anything on or over the airbag module.Placing objects on or over the airbag inflation area may causethose objects to be propelled
How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suffic
WARNING: If the airbag has deployed, the airbag will notfunction again and must be replaced immediately. If theairbag is not replaced, the unrepaired
• the system determines that an infant is present in a rear-facing infantseat that is installed according to the manufacturer’s instructions,• the sys
• When the front passenger sensing system enables the front passengerfrontal airbag (may inflate), the indicator will be unlit and stay unlit.If a per
WARNING: Sitting improperly out of position or with the seatback reclined too far can take off weight from the seat cushionand affect the decision of
WARNING: To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a chi
Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature, the needle will be inthe normal range (between “
WARNING: Any alteration/modification to the front passengerseat may affect the performance of the front passenger sensingsystem.Determining if the sys
WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. Contact your authorize
The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of
WARNING: Do not attempt to service, repair, or modify theSafety Canopy威 system, its fuses, the A, B, or C pillar trim, orthe headliner on a vehicle co
• Two crash sensors mounted in the front doors (one on each side ofthe vehicle).• Crash sensors located on the C pillars (one sensor on each pillar on
WARNING: If the SafetyCanopy system hasdeployed, the Safety Canopy willnot function again unless replaced.The Safety Canopy system(including the A, B
• pressing the hazard control button,• or pressing the panic button on the remote entry transmitter.The feature will continue to operate until the veh
Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb
Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe
WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli
Odometer: Registers the total miles(kilometers) of the vehicle.Refer to Message center in theInstrument cluster chapter on howto switch the display fr
Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle.If the child is the proper height, age, and weigh
position whenever possible. If all children cannot be seated andrestrained properly in a rear seating position, properly restrain thelargest child in
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out.6. All
10. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the
Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol.The LATCH anchors are locat
WARNING: Never attach two child safety seats to the sameanchor. In a crash, one anchor may not be strong enough to holdtwo child safety seat attachmen
The tether strap anchors in yourvehicle are in the following positions(shown from top view):Attach the tether strap only to the appropriate tether anc
3. Open the tether anchor cover.4. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safety seat maynot
Although the lap/shoulder belt will provide some protection, childrenwho have outgrown a typical child seat are still too small for lap/shoulderbelts
Seating and Safety Restraints 138Seating 138Personal Safety System™ 157Safety belt system 160Airbags 171Child restraints 186Tires, Wheels and Loading
MILES (km) TO EThis displays an estimate of approximately how far you can drive withthe fuel remaining in your tank under normal driving conditions.Re
Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli
WARNING: The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydro
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
WARNING: Under-inflation is the most common cause of tirefailures and may result in severe tire cracking, tread separationor “blowout”, with unexpecte
Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo
Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
MPG (L/km)This displays instantaneous fuel economy as a bar graph ranging from ↓poor economy to ↑ excellent economy.Your vehicle must be moving to cal
WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w
• Do not run over curbs or hit the tire against a curb when parkingWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the
• Front-wheel drive (FWD) vehicles(front tires at top of diagram)• All-wheel drive (AWD) vehicles(front tires at top of diagram)Sometimes irregular ti
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including inter
OIL LIFEThis displays the remaining oil life.An oil change is required whenever indicated by the message center andaccording to the recommended mainte
To restore the full functionality of the tire pressure monitoring system,have the damaged road wheel/tire repaired and remounted on yourvehicle. For a
Low tirepressurewarning lightPossible cause Customer action requiredFlashingwarning lightSpare tire in use Repair the damaged road wheel/tireand reins
SNOW TIRES AND CHAINSWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel
SUMMER TIRESYour Taurus SHO may be equipped with summer tires to providesuperior performance on wet and dry roads. Summer tires do not havethe Mud and
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
Steps for determining the correct load limit:1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.
COLLISION WARN GAP (if equipped)This allows you to adjust the sensitivity setting of the collision warningsystem. See Collision Warning System in the
calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 -540 = -103 kg. You will need to reduce the load weight by at least240 lb. (104
WARNING: Do not exceed the GVWR or the GAWR specified onthe certification label.WARNING: Towing trailers beyond the maximum recommendedgross trailer w
WARNING: Do not operate Adaptive Cruise Control (ACC)when towing a trailer equipped with brakes. Aftermarket trailerbrakes will not function properly
Trailer towing tips• Practice turning, stopping and backing-up before starting on a trip toget the feel of the vehicle-trailer combination. When turni
If you tow your vehicle with all four wheels on the ground, follow theseinstructions:• Tow only in the forward direction.• Release the parking brake.•
STARTINGPositions of the ignition (if equipped)If your vehicle is equipped with a push button start system, refer toPush button start system in this s
WARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine compartment and exhaus
• Make sure the gearshift lever is inP (Park).3. Turn the key to 3 (on) withoutturning the key to 4 (start).If your vehicle is equipped with apush but
3. After idling for a few seconds, release the parking brake, apply thebrake, shift into gear and drive.Note: If the engine does not start on the firs
3. On — press and hold the START/STOP button for at least one secondwithout applying the brake pedal. This will power your vehicle’s electricalsystem
TIRE MOBILITY KIT EXP 1, 2, 3, 4 YR (if equipped)Use this feature to set the expiration date that is listed on the tiremobility kit sealant canister.
Fast Restart Feature: The Fast Restart feature allows you to re-startyour vehicle within 20 seconds of switching the vehicle off, if a valid IAkey is
Important ventilating informationIf the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least 1 inch (2.5
• To reduce the risk of electrical shock, do not use your heater withungrounded electrical systems or two pronged (cheater) adapters.Also ensure that
Refer to Warning lights andchimes in the Instrument Clusterchapter for information on the brakesystem warning light.Four-wheel anti-lock brake system
Even when the ABS is disabled,normal braking is still effective. Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake
The parking brake is not recommended to stop a moving vehicle.However, if the normal brakes fail, the parking brake can be used to stopyour vehicle in
WARNING: Remember that even advanced technology cannotdefy the laws of physics. It’s always possible to lose control of avehicle due to inappropriate
authorized dealer immediately. If equipped with a message center, thevehicle will also indicate a failure with the brake system.Note: If the system ca
Electronic stability control (ESC)Electronic stability control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa
AdvanceTrac威 FeaturesControlfunctionsModeStabilitycontroloff lightMessage centerdisplayESC TCSDefault atstart-upSystemInitializationTurns onduringbulb
REAR LEFT DOOR AJAR — Displayed when the rear left door is notcompletely closed.REAR RIGHT DOOR AJAR — Displayed when the rear right door isnot comple
STEERING3.5L V6 engine (SHO): Your vehicle is equipped with an electric powersteering (EPS) system. There is no fluid reservoir to check or fill.If yo
3.5L V6 engine: Your vehicle is equipped with a hydraulic steeringsystem.To help prevent damage to the power steering system, never hold thesteering w
If you cannot move the gearshift lever out of P (Park) with the ignitionin the on position and the brake pedal pressed, it is possible that a fusehas
AUTOMATIC TRANSMISSION OPERATIONAutomatic transmission adaptive learningYour transmission is equipped with an adaptive learning strategy found inthe v
R (Reverse)With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Re
To return to O/D (overdrive mode), press the transmission control switchagain.• The Grade Assist lamp in the instrument cluster will not beilluminated
P (Park)This position locks the transmissionand prevents the front wheels fromturning.To put your vehicle in gear:• Press the brake pedal• Move the ge
M (Manual)With the gearshift lever in M(Manual), the driver can changegears up or down (without a clutch)as desired. This is called SelectShiftAutomat
Recommended shift speedsUpshift according to the following chart:Upshifts when accelerating (recommended for best fueleconomy)Shift from:1 - 2 15 mph
WARNING: To help avoid personal injury, always use cautionwhen in R (Reverse) and when using the RSS.WARNING: This system is not designed to prevent c
TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressuresensor is malfunctioning, or your spare tire is in use. For moreinformation on how the syst
The RSS automatically turns on when the gearshift lever is placed in R(Reverse) and the ignition is on. An RSS control on the instrument panelallows t
• (1) Rear bumper• (2) Red zone• (3) Yellow zone• (4) Green zoneAlways use caution while backing.Objects in the red zone are closest to your vehicle a
WARNING: The camera system is a reverse aid supplementdevice that still requires the driver to use it in conjunction withthe rear view mirror and the
WARNING: This system is designed to be a supplementarydriving aid. It is not intended to replace the driver’s attention,and judgment, or the need to a
• Pedestrians or objects in the roadway.• Oncoming vehicles in the same lane.• Severe weather conditions (see also blocked sensor section).• Debris bu
Cause ActionThe surface of the radar in thegrille is dirty or obstructed insome wayClean the grille surface in front ofthe radar or remove the objectc
BLIND SPOT MIRRORS (IF EQUIPPED)Blind spot mirrors have an integrated convex spotter mirror built intothe upper outboard corner of the outside mirrors
BLIND SPOT INFORMATION SYSTEM (BLIS姞) WITH CROSSTRAFFIC ALERT (CTA) (IF EQUIPPED)The BLIS威 is a convenience featurethat aids the driver in assessingwh
The BLIS威 will trigger the alert for vehicles that enter your blind zonefrom the rear or merge into the blind zone from the side. Vehicles thatyou pas
Cross traffic alert (CTA) system operationThe CTA system warns the driver of approaching vehicles when R(Reverse) is selected and the vehicle is backi
OIL CHANGE REQUIRED — Displayed when the oil life left reaches0%.BLIND SPOT SYSTEM FAULT (if equipped) — Displayed when afault with the blind spot inf
CTA coverage also decreases when parking at shallow angles (refer tofigure for approximate zone coverage areas [sensor obstructed forvehicle on left])
CTA and reverse sensing system (RSS) interactionCTA works along with the reverse sensing system (RSS) (if equipped).Become familiar with the warning t
WARNING: Just prior to the system recognizing a blockedcondition and alerting the driver, the number of missed objectswill increase. To help avoid inj
Day and night brightnessThe BLIS威 and/or CTA alert will automatically dim when the headlampswitch is in PARK, ON, or AUTO ON and night time darkness h
driving surfaces are relatively level, obstruction-free and otherwisesimilar to normal on-road driving conditions. Operating your vehicleunder other t
Your vehicle is equipped with Traction Control™, it may be beneficial todisengage the Traction Control™ system while attempting to rock thevehicle.Do
AWD Systems (if equipped)AWD uses all four wheels to power the vehicle. This increases traction,enabling you to drive over terrain and road conditions
Driving through deep water may damage the engine ortransmission.If the front or rear axle is submerged in water, the axle lubricant andPTU (Power Tran
Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;
Maintenance and modificationsThe suspension and steering systems on your vehicle have been designedand tested to provide predictable performance wheth
CRUISE OVERRIDE (if equipped) — Displayed when the acceleratorpedal is being pressed while ACC is active.CRUISE NOT AVAILABLE (if equipped) — Displaye
ROADSIDE ASSISTANCEVehicles sold in the U.S. : Getting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany off
Vehicles sold in the U.S. : Using roadside assistanceComplete the roadside assistance identification card and place it in yourwallet for quick referen
FUEL PUMP SHUT-OFFIn the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fue
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
Passenger compartment fuse panelThe fuse panel is located under the instrument panel to the left of thesteering wheel.The fuses are coded as follows.F
Fuse/RelayLocationFuse AmpRatingProtected Circuits8 10A Low beam headlamps (right)9 15A Interior lights, Cargo lamps10 15A Switch illumination, Puddle
Fuse/RelayLocationFuse AmpRatingProtected Circuits29 5A Instrument panel cluster,Heads-up display30 5A Not used (spare)31 10A Not used (spare)32 10A A
Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot
Fuse/RelayLocationFuse AmpRatingPower Circuits4 30A** Front wiper5 30A** Passenger seat6 20A** Cigar lighter7 60A** Engine cooling fan (non-SHOengine)
Fuse/RelayLocationFuse AmpRatingPower Circuits31 — Not used32 30A** Driver seat33 30A** Intelligent access (IA)34 — Not used35 40A** Front heater blow
RESTART NOW OR KEY IS NEEDED (if equipped) — Displayedwhen the start/stop button is pressed to shut off the engine and aIntelligent Access Key is not
Fuse/RelayLocationFuse AmpRatingPower Circuits59 Half ISO relay Left halogen headlamp relay60 Half ISO relay Right halogen headlamp relay61 — Not used
Dissimilar spare tire/wheel informationWARNING: Failure to follow these guidelines could result in anincreased risk of loss of vehicle control, injury
3. Full-size dissimilar spare without label on wheelWhen driving with the full-size dissimilar spare tire/wheel, do not:• Exceed 70 mph (113 km/h)• Us
Stopping and securing the vehicle1. Park on a level surface, set theparking brake and activate hazardflashers.2. Place gearshift lever in P (Park)and
Tire change procedureWARNING: When one of the front wheels is off the ground, thetransmission alone will not prevent the vehicle from moving orslippin
WARNING: To lessen the risk of personal injury, do not put anypart of your body under the vehicle while changing a tire. Do notstart the engine when y
Stowing the tire and jack1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown.
If you are stowing the flat tire:1. Remove the extension bolt fromthe exterior pocket of the felt bag.2. Install the jack as shown inStep 4 under Stow
1. Air compressor (inside)2. Diverter knob3. On/Off button4. Air pressure gauge5. Deflation button6. Sealant bottle/canister7. Sealant filling clear t
• Periodically monitor tire inflation pressure in the affected tire; if thetire is losing pressure, have the vehicle towed.• Read the information in t
Customer Assistance 312Reporting safety defects (U.S. only) 319Reporting safety defects (Canada only) 319Cleaning 320Maintenance and Specifications 32
VEHICLE NEAR TOP SPEED — Displayed when a MyKey威 is in useand the MyKey speed limit is on and the vehicle speed is approaching80 mph (130 km/h). Refer
• When inflating a tire or other objects, use the black air hose only. Donot use the transparent hose which is designed for sealant applicationonly.•
4. Plug the power cable into the 12Vpower point in the vehicle.5. Remove the warning sticker found on the canister and place it on thetop of the instr
Note: When the sealing compound is first added into the tire, theair pressure gauge reading on the compressor unit may indicate ahigher value; this is
3. Turn the dial clockwise to the air position. Turn on the kit by pressingthe on/off button.4. Adjust the tire to therecommended inflation pressurefr
Removal of the sealant canister from the temporary mobility kit1. Unwrap the clear tube from thecompressor housing.2. Press the button located on thet
2. Once aligned, seat the sealantcanister by lightly pushing downuntil you hear an audible click.3. Wrap the clear tube around thecompressor housing.N
WHEEL LUG NUT TORQUE SPECIFICATIONSRetighten the lug nuts to the specified torque within 100 miles (160 km)after any wheel disturbance (rotation, flat
WARNING: Do not insert the nozzle of portable fuel containersor aftermarket funnels into the Easy Fuel威 system. This coulddamage the fuel system and i
Connecting the jumper cablesNote: In the illustration, the vehicle on the bottom is used to designatethe assisting (boosting) battery.1. Connect the p
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.Note: In the illustration, the vehicle on the bottom i
ACTIVE PARK SEARCHING (if equipped) — May display whenusing the active park assist system. See Active park assist in theDriving chapter for more infor
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
If the vehicle is towed by other means or incorrectly, vehicledamage may occur.Ford Motor Company produces a towing manual for all authorized towtruck
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehi
In Canada:Mailing addressCustomer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Telephone1-800-565-367
IN CALIFORNIA (U.S. ONLY)California Civil Code Section 1793.2(d) requires that, if a manufactureror its representative is unable to repair a motor veh
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
If your vehicle must be serviced while you are traveling or living inAsia-Pacific Region, Sub-Saharan Africa, U.S. Virgin Islands, CentralAmerica, the
If you buy your vehicle in North America and then relocate to any of theabove locations, register your vehicle identification number (VIN) andnew addr
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im
AUDIO SYSTEMSAM/FM CD/MP3 satellite compatible sound systemWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i
WAXING• Wash the vehicle first.• Use a quality wax that does not contain abrasives.• Do not allow paint sealant to come in contact with any non-body(l
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
3.5L V6 ENGINE3.5L V6 SHO ENGINECleaning3232012 TaurusOwners Guide, 1st PrintingUSA (fus)
PLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authorized dealer.• For r
INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENSClean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth,
INTERIORFor fabric, carpets, cloth seats, safety belts and seats equipped with sideairbags:• Remove dust and loose dirt with a vacuum cleaner.• Remove
UNDERBODYFlush the complete underside of your vehicle frequently. Keep body anddoor drain holes free from packed dirt.FORD AND LINCOLN CAR CARE PRODUC
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column.2. Go to th
Setting the clockTo set the time, press CLOCK. Thedisplay will read SET TIME. Use thememory preset numbers (0–9) toenter in the desired time–hours and
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.5L V6 engine1. Power steering fluid reservoir2. Engine coolant reservoir3. Brake fluid reservoir4. B
3.5L V6 SHO engine1. Engine coolant reservoir2. Brake fluid reservoir3. Battery4. Power distribution box5. Air filter assembly6. Automatic transmissio
Engine shieldSome vehicles may be equipped with an aero-shield under the engine.This shield needs to be removed for service, including oil and filterc
CHANGING THE WIPER BLADES1. Pull the wiper blade and armaway from the glass.2. Squeeze the locking tabs torelease the blade from the arm andpull the b
5. Locate and carefully remove theengine oil level dipstick.6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil l
2. If the engine oil level is not within the normal operating range, addonly certified engine oil of the recommended viscosity. Remove theengine oil f
Do not use supplemental engine oil additives, cleaners or other enginetreatments. They are unnecessary and could lead to engine damage thatis not cove
Ford production and Motorcraft威 replacement oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedthat
WARNING: When lifting a plastic-cased battery, excessivepressure on the end walls could cause acid to flow through thevent caps, resulting in personal
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
MEMORY PRESETS (0–9): Whentuned to any station, press and holda preset button until sound returnsand PRESET # SAVED appears in the display. You can sa
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the FULL COLD level, or within theCOLD
• DO NOT MIX different colors or types of coolant in your vehicle.Make sure the correct coolant is used. Mixing of engine coolants mayharm your engine
3. Step back while the pressure releases.4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and re
Severe climatesIf you drive in extremely cold climates:• It may be necessary to increase the coolant concentrationabove 50%.• NEVER increase the coola
• The service engine soon indicator will illuminate.If the engine reaches a preset over-temperature condition, the enginewill automatically switch to
5. Re-start the engine and take your vehicle to an authorized dealer.Driving the vehicle without repairing the engine problemincreases the chance of e
• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kindcan lead to eye and respiratory tract irritation. In severe cases,excessive or p
RefuelingWARNING: Fuel vapor burns violently and a fuel fire can causesevere injuries. To help avoid injuries to you and others:• Read and follow all
4. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about five seconds after pumping fuel before removing thefuel filler noz
Octane recommendations3.5L V6 engine“Regular” unleaded gasoline with apump (R+M)/2 octane rating of 87 isrecommended. Some stations offerfuels posted
CD/MP3 PlayerCD: Press to enter CD/MP3 mode. Ifa disc is already loaded into thesystem, CD/MP3 play will beginwhere it ended last. If no CD is loaded,
Cleaner airFord endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality, per the recommendations in the Choosing the rightf
1. After lifting the trunk cargocover, locate the white plasticfunnel. It is attached to the rear,lower edge of the spare tirecompartment.2. Slowly in
The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fu
Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fuelecon
• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled mainten
If other than Ford, Motorcraft威 or Ford-authorized parts are used formaintenance replacements or for service of components affectingemission control,
2. Poor fuel quality or water in the fuel—the engine may misfire or runpoorly.3. The fuel fill inlet may not have been properly closed. See Easy Fuel威
The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not
BRAKE FLUIDThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX
4. Latch the gearshift lever in P (Park) and leave the engine running.5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. Ifneces
SEEK: Press SEEK toaccess the previous/next track.CAT (Category) / FOLD(Folder):In MP3 mode only– PressCAT/FOLD and thenpressSEEK to access the previo
C. Remove the bolt cover (ifequipped).D. Remove two bolts that attach the air filter assembly to the front ofthe vehicle (2).E. Loosen the clamp holdi
WARNING: Do not run engine with the air filter disconnected.Start the engine and continue with Step 6.6. Install the dipstick making sure it is fully
Adjusting automatic transmission fluid levelsBefore adding any fluid, make sure the correct type is used. The type offluid used is normally indicated
AIR FILTERRefer to scheduled maintenance information for the appropriateintervals for changing the air filter element.When changing the air filter ele
4. Wipe the air filter housing and cover clean to remove any dirt ordebris and to ensure good sealing.5. Install a new air filter element. Be careful
• Touch-up raw or primed metal to prevent rust.• Cover chrome and stainless steel parts with a thick coat of auto waxto prevent discoloration. Re-wax
Brakes• Make sure brakes and parking brake are fully released.Tires• Maintain recommended air pressure.Miscellaneous• Make sure all linkages, cables,
MOTORCRAFT PART NUMBERSComponent 3.5L V6 Engine 3.5L V6 SHO engineAir filter element FA-1884 FA-1884Battery BXT-59 BXT-65–650Oil filter FL-500-S FL-50
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItems CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationBrake fluidBetween MAX a
Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine oil5.5 quarts (5.2L)(3.5L V6 engine)•Motorcraft威 SAE 5W-20Premium
Satellite Radio (if equipped)Satellite radio is available only with a valid SIRIUS威 radiosubscription. Check with your authorized dealer for availabil
Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine coolant(3.5L V6 engine)411.1 quarts(10.5L)Motorcraft威 SpecialtyGre
Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationFuel tank19.0 gallons(71.9 L)——1Approximate dry fill capacity. Actual amo
ENGINE DATAEngine 3.5L V6 engine 3.5L V6 SHO engineCubic inches 214 214FuelSee Octanerecommendationsearlier in this chapter.See Octanerecommendations
3.5L V6 SHO engineIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requireth
Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX
TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis
FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C
Peace of mind•Remote start •Vehicle tracking and recovery*•Wheel locks•Locking fuel plug for capless fuel system•Bumper mounted parking sensors**Ford
FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 30 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the
Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With
MEMORY PRESETS (0–9): Thereare 30 available presets, 10 each forSAT1, SAT2 and SAT3. To savesatellite channels in your memory presets, tune to the des
Ford Extended Service Plan3802012 TaurusOwners Guide, 1st PrintingUSA (fus)
FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is
GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?This guide describes the scheduled maintenance required for yourvehicle. Carefully following
Your vehicle is very sophisticated and built with multiple complexperformance systems. Every manufacturer develops these systems usingdifferent specif
ConvenienceMany dealerships have extended evening and Saturday hours to makeyour service visit more convenient. How’s that for quality service?Factory
Engine oil/coolant change intervalsEngine oil As indicated by the message center: do notexceed one year or 10,000 miles (16,000 km)Engine coolant,init
Multi-point inspectionIn order to keep your vehicle running right, it is important to have thesystems on your vehicle checked regularly. This can help
Scheduled Maintenance3872012 TaurusOwners Guide, 1st PrintingUSA (fus)
NORMAL SCHEDULED MAINTENANCE AND LOGIntelligent Oil Life Monitor™Your vehicle is equipped with an Intelligent Oil Life Monitor™ thatdetermines when th
Normal Scheduled MaintenanceAt every oil changeinterval as indicatedby the messagecenterChange engine oil and filterRotate tires, inspect tire wear an
• SONG SEEK MENU- Press OK to enter song seek menu.PressSEEK to scroll through the following options:a. SAVE THIS SONG: Press OK to save the currently
Additional maintenance items1Miles (x 1,000) 20 30 40 60 80 90 100 120 140 150Kilometers (x 1,000) 32 48 64 96 128 144 160 192 225 240Replace cabin ai
Maintenance schedule logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDAT
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
SPECIAL OPERATING CONDITIONSIf you operate your vehicle primarily in any of the following conditions,you need to perform additional maintenance as ind
Perform the services in the preceding table when specified or within3,000 miles (4,800 km) of the OIL CHANGE REQUIRED messageappearing in the message
Special operating condition logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
EXCEPTIONSThere are several exceptions to the Normal Schedule. They are listedbelow:Normal vehicle axle maintenance: Rear axles and power take-off(PTO
using oils defined by the American Petroleum Institute (API)performance category of API SK or earlier (for example SJ, etc).Edge/MKX AWD only – vehicl
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
• CHANNEL LOCKOUT MENU- Press OK to enter the ChannelLockout menu. Press the SEEK to scroll through the followingoptions:a. LOCK/UNLOCK THIS CHANNEL:
AAccessory delay ...84Adaptive Cruise Control ...89AdvanceTrac ...245AdvanceTrac Sport Mod
Changing a tire ...290Child safety seats ...190attaching with tether straps ..196in front seat ...
running out of fuel ...306, 350Emission control system ...354Engine ...372cleaning ...
Illuminated visor mirror ...78Infant seats(see Safety seats) ...190Inspection/maintenance (I/M)testing ...
OOctane rating ...349Oil (see Engine oil) ...333Overdrive ...253PParental MyKe
Safety ComplianceCertification Label ...373Satellite Radio Information ...47Scheduled Maintenance GuideNormal ScheduledMaintenan
VVehicle Identification Number(VIN) ...374Vehicle loading ...223Ventilating your vehicle
SPEED COMPENSATED VOLUME: With this feature on, radio volumeautomatically gets louder with increasing vehicle speed to compensatefor road and wind noi
Auxiliary input jack (Line in)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends th
5. Turn the portable music player on and adjust the volume to 1/2 thevolume.6. Press AUX on the vehicle radio repeatedly until LINE, LINE IN orSYNC LI
USB port (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdriver
CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C
CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
Radio Display Condition Action RequiredNO TEXT Category informationnot available.Category informationnot available at thistime on this channel.The sys
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the
4. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. A/Cengages automaticall
During extreme high ambient temperatures when idling stationary forextended periods of time in gear, it is recommended to run the A/C inthe MAX A/C mo
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the In
4. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. A/Cengages automaticall
11. Driver cooled seat (if equipped): Press to control the drivercooled seat. Refer to Front seating in the Seating and SafetyRestraints chapter for m
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL (NAVIGATIONBASED – IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Messa
6. Passenger cooled seat (if equipped): Press to control thepassenger cooled seat. Refer to Front seating in the Seating and SafetyRestraints chapter
TOUCHSCREEN FUNCTIONSTemperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the Instrument Cluster chapter.Temper
BREAKING-IN YOUR VEHICLEYour vehicle does not need an extensive break-in. Try not to drivecontinuously at the same speed for the first 1,000 miles (1,
VOICE COMMANDS IN CLIMATE MODEPlease refer to the Voice commands in climate mode section of theNavigation supplement for more information on using voi
To increase airflow to the outer instrument panel vents, close the ventslocated in the middle of the instrument panel.REAR WINDOW DEFROSTERRThe rear d
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the low beam headlampso
4. Turn the headlamp control to the autolamp position. The headlampswill turn on.5. Wait the desired amount of time for the exit delay you want (up to
Scenario 3:Conditions - The automatic high beam system is set to ON in themessage center. The headlamp switch is in(off), (park lamps),or(on).Operatio
• The camera is blocked.Note: Activating the multi-function lever will put the headlamps inmanual high beam mode (constant or flash-to-pass) until the
For significant blockages (e.g. bird dropping, bug splatter, snow, or ice),the automatic high beam system uses a blocked sensor computerprogram. If a
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicablelit components in the vehicle duringheadlamp and parking lam
To see a clearer light pattern for adjusting, you may want to block thelight from one headlamp while adjusting the other.For vehicles with halogen hea
INTERIOR LAMPSFront row map lampsThe map lamps are located on theoverhead console. Press the controlson either side of each map lamp toturn on the lam
DATA RECORDINGService Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehi
The lights come on whenever the ignition is in either the on or accessoryposition and the headlamps or parking lamps are on.Note: The ambient lights w
Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbs mustbe marked with an authorized “D.O.T.” for North America an
2. Reach in behind the headlamp assembly to access the bulbs andconnectors.3. Remove the outboard rubber bootfrom the lamp assembly by pullingrearward
Replacing rear brake/tail/turn and sidemarker lamp bulbsThe brake/tail/turn and side marker lamp bulbs are located in the taillamp assembly. Follow th
Replacing backup lamp bulbsThe backup lamp bulbs are located in the deck lid assembly.1. Make sure the headlamp switch is in the off position.2. Remov
Replacing license plate lamp bulbs1. Make sure the headlamp switch isin the off position.2. Remove the two screws from thelicense plate lamp assembly.
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate toward you to decrease thes
Courtesy wipe feature: One extra wipe will occur a few seconds afterwashing the front window to clear any excess washer fluid remaining onthe windshie
ILLUMINATED VISOR MIRRORLift the mirror cover to turn on thevisor mirror lamp.Slide-on-rod featureRotate the visor towards the sidewindow and extend i
ELECTRONIC COMPASS (IF EQUIPPED)The compass heading is displayed in the center integrated display (CID).The compass reading may be affected when you d
limitations regarding 911 Assist and Traffic, directions andInformation privacy below). However, parties, such as lawenforcement, could combine the ED
4. Press and release the 7 and 9radio preset buttons together,repeatedly until ZONE XX changesto the correct zone (1–15) in theCID.5. The direction wi
CENTER CONSOLEYour vehicle may be equipped with a variety of console features. Note:The appearance and features of the center console may be different
AUXILIARY POWER POINT (12V DC)Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will dama
POWER WINDOWSWARNING: Do not leave children unattended in the vehicle anddo not let children play with the power windows. They mayseriously injure the
• If or is pressed during the opening operation, both windowsand moon roof movement will stop.Note: The ignition must be in the off position and the a
INTERIOR MIRRORThe interior rearview mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side.W
EXTERIOR MIRRORSPower side view mirrorsWARNING: Do not adjust the mirror while the vehicle is inmotion.To adjust your mirrors:1. Rotate the control cl
Fold-away mirrorsFold the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.Blind spot mirrors (if equipped)Your
SPEED CONTROLWith speed control set, you can maintain a set speed without keepingyour foot on the accelerator pedal.WARNING: Do not use the speed cont
Resuming a set speedPress and release RESUME. This will automatically return the vehicle tothe previously set speed.Increasing speed while using speed
CELL PHONE USEThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri
WARNING: Always pay close attention to changing roadconditions, especially when using Adaptive Cruise Control.Adaptive Cruise Control cannot replace a
3. Press and release the SET +control. The vehicle speed will bestored in the memory and themessage center will display SETXXX MPH (your desired speed
If the ACC system predicts that itsmaximum braking level will not besufficient, an audible warning willsound while the ACC continues tobrake. This is
Disengaging adaptive cruise controlPress the brake pedal to disengage the adaptive cruise control. CRUISECANCELLED will be displayed in the message ce
Resuming the set speedPress and release the RESUMEcontrol. This will automaticallyreturn the vehicle to the previouslyset speed. The set speed will di
Turning off cruise controlPress the OFF button to turn off thecruise control.Note: When you turn off the cruisecontrol or the ignition, your cruisecon
• There may be issues with the detection of vehicles in front whendriving into and coming out of a bend or curve in the road.In these cases ACC may br
Blocked sensorIf a message regarding a blockedsensor is displayed, the radar signalsfrom the sensor have beenobstructed. The sensor is locatedbehind a
WARNING: Do not use ACC when towing a trailer with brakecontrols. Aftermarket trailer brakes will not function properlywhen ACC is activated because t
SYNC威 system hands-freecontrol feature (if equipped)Pressbriefly to use the voicecommand feature. You will hear atone and LISTENING will appear inthe
Commentaires sur ces manuels