Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Message center 20Entertainment Systems 29AM/FM stereo with CD/MP3 29Auxiliary
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
3. Enter factory–set 5–digit entry code.4. Press and hold the 3 • 4. While holding the 3 • 4, press and releasethe 7 • 8. While still holding the 3 •
the following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including i
One step door unlockingIf the one step door unlocking feature is activated, pressand releaseonce to unlock all of the doors, the liftgate and liftgate
Replacing the batteryThe integrated keyhead transmitter uses one coin type three-volt lithiumbattery CR2032 or equivalent.To replace the battery:1. Tw
The illuminated entry system will turn off the lights if:• the ignition is turned to the on position, or• the integrated keyhead transmitter lock cont
2. Within five seconds press the 1 • 2 on the keypad. The doors will lockand then unlock to confirm that the system is in programming mode.3. Enter yo
To unlock all doors and liftgate, press the 3 • 4 control within fiveseconds of entering the factory set 5-digit code or your personal code.To lock al
Anti-theft indicatorThe anti-theft indicator is located in the instrument panel cluster.• When the ignition is in the offposition, the indicator will
keyless entry transmitter. A maximum of eight coded keys can beprogrammed to your vehicle; only four of these eight keys can be IKTswith remote entry
4. After three seconds but within 10 seconds of turning the ignition tothe 1 (off) position, insert the second previously coded key into theignition.5
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
FRONT SEATSWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the eve
To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o
To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous
WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting the front manual seat (if eq
WARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event of a col
Press the control to move the seatforward, backward, up or down.Heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbeca
WARNING: To minimize the risk of neck injury in the event of acrash, the driver and passenger occupants should not sit inand/or operate the vehicle, u
Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as possible to theba
To reinstall the adjustable head restraint, do the following:1. Insert the two stems into theguide sleeve collars.2. Push the head restraint downuntil
3. Flip seat forward.Attach the safety belt web snapbutton to the quarter trim panelsnap button. This will ensure thatsafety belt does not get caught
WARNING LIGHTS AND CHIMESBase instrument cluster shown in standard measure. Metricsimilar.Optional instrument cluster shown in standard measure. Metri
5. Rotate seatback down into loadfloor position.Returning the second row seats to upright position1. Pull seatback up and into uprightposition making
WARNING: Make sure safety belt buckle heads are throughelastic holders on seat backs. Safety belt buckles may break ifthey are trapped underneath the
To install the second row cushion1. Push the cushion to the inboardside of the vehicle.2. Make sure that the hinges arelocked into place.SAFETY RESTRA
conditions. A collection of crash and occupant sensors providesinformation to the Restraints control module (RCM). During a crash, theRCM may activate
occupant is not properly restrained by safety belts or child safety seatsand they move forward during pre-crash braking. The most effective wayto redu
increase the effectiveness of the safety belts. In frontal collisions, thesafety belt pretensioners can be activated alone or, if the collision is ofs
WARNING: To reduce the risk of injury, make sure children sitwhere they can be properly restrained.WARNING: Never let a passenger hold a child on his
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
Pregnant women should alwayswear their safety belt. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips
When to use the automatic locking modeThis mode should be used any time a child safety seat, except abooster, is installed in passenger front or rear
Many lights will illuminate when you start your vehicle to make sure thebulbs work. If any light remains on after starting the vehicle, refer to there
WARNING: After any vehicle collision, the safety belt system atall passenger seating positions must be checked by an authorizeddealer to verify that t
WARNING: The driver and front passenger safety belt system(including retractors, buckles and height adjusters) must bereplaced if the vehicle is invol
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war
If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the onposition or less than1-2 minutes h
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...⬙Crashes are ra
WARNING: Do not sit on top of a buckled safety belt or insert alatchplate into the buckle to avoid the Belt-Minder威 chime. Todo so may adversely affec
3. For the seating position being disabled, buckle then unbuckle thesafety belt three times, ending in the unbuckled state.• After Step 3, the safety
Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in
WARNING: Do not attempt to service, repair, or modify theairbag supplemental restraint systems or its fuses. Contact yourauthorized dealer as soon as
How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustains alongitudinal deceleration suff
Brake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the on
• seat-mounted side airbags. Refer to Seat-mounted side airbag systemlater in this chapter• Safety Canopy威 System. Refer to Safety Canopy威 System late
The front passenger sensing system will disable (will not inflate) thefront passenger’s frontal airbag if:• the front passenger seat is unoccupied, or
The front passenger sensing system is designed to enable (may inflate)the front passenger’s frontal airbag anytime the system senses that aperson of a
WARNING: Sitting improperly out of position or with the seatback reclined too far can take off weight from the seat cushionand affect the decision of
WARNING: To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a chi
WARNING: Any alteration/modification to the front passengerseat may affect the performance of the front passenger sensingsystem.Determining if the sys
WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. See an authorized deal
The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuittha
Safety Canopy姞 SystemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a deploying
How does the Safety Canopy姞 System work?The design and development of theSafety Canopy System includedrecommended testing proceduresthat were develope
Charging system: Illuminates whenthe battery is not charging properly.If it stays on while the engine isrunning, there may be a malfunctionwith the ch
The Safety Canopy System is designed to active when the vehiclesustains lateral deceleration sufficient to cause the RCM to initiate safetycanopy infl
Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref
SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme
Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb
Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe
WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli
Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle.If the child is the proper height, age, and weigh
Installing child safety seats with combination lap and shoulderbeltsThe rear seat head restraints must be removed when using a childseat that utilizes
1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
Speed control: Illuminates whenthe speed control is engaged. Turnsoff when the speed control systemis disengaged.Overdrive cancel and gradeassist: Ill
9. Attach the tether strap (if thechild seat is equipped). Refer toAttaching child safety seats withtether straps later in this chapter.10. Before pla
Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol.The LATCH anchors are locat
only be used at this seating position provided that the child seatmanufacturer’s instructions permit use with the anchor spacing stated.Do not attach
The tether strap anchors in yourvehicle are in the following positions(shown from top view):Attach the tether strap only to the appropriate tether anc
3. Clip the tether strap to theanchor as shown.The arrow in the above graphicpoints toward the front of thevehicle.If the tether strap is clippedincor
Booster seats position a child so that vehicle lap/shoulder safety belts fitbetter. They lift the child up so that the lap belt rests low across the h
Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
Message center activation chime (if equipped): Sounds when awarning message (except PARKING BRAKE ENGAGED while parked)appears in the message center d
conventional two-wheel drive vehicle cannot. The 4WD system is activeall the time and requires no input from the operator.For 4WD vehicles, a spare ti
• Narrower – to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUVs and
government test course. For example, a tire graded 150 would wear oneand one-half (11⁄2) times as well on the government course as a tiregraded 100. T
• Tire Identification Number (TIN): A number on the sidewall ofeach tire providing information about the tire brand andmanufacturing plant, tire size
At least once a month and before long trips, inspect each tire and checkthe tire pressure with a tire gauge (including spare, if equipped). Inflateall
To check the pressure in your tire(s):1. Make sure the tires are cool, meaning they are not hot from drivingeven a mile.If you are checking tire press
the valve stem. Inspect the tire sidewalls for cracking, cuts, bruises andother signs of damage or excessive wear. If internal damage to the tire issu
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w
Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t
Optional instrument cluster shown in standard measure. Metricsimilar.Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge:
Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your
• Rear-wheel drive (RWD)vehicles/Four-wheel drive(4WD)/All-wheel drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can b
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
11. Maximum Load: Indicates the maximum load in kilograms andpounds that can be carried by the tire. Refer to the Safety ComplianceCertification Label
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including inter
To restore the full functionality of the tire pressure monitoring system,have the damaged road wheel/tire repaired and remounted on yourvehicle. For a
WARNING: Never remove the coolant reservoir cap while theengine is running or hot.Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel
Low tirepressurewarning lightPossiblecauseCustomer action requiredFlashing warninglightSpare tire inuseYour temporary spare tire is in use.Repair the
SNOW TIRES AND CABLESWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel
VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the
• A final example for your vehicle with 1,400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the
Seating and Safety Restraints 110Seating 110Safety restraints 122Airbags 136Child restraints 152Tires, Wheels and Loading 169Tire information 171Tire
Trip odometer: Registers the miles (kilometers) of individual journeys.• Standard instrument cluster:Press the SELECT/RESET controlonce to switch from
TRAILER TOWINGTrailer towing with your vehicle may require the use of a trailer towoption package.Trailer towing puts additional loads on your vehicle
Powertrain Maximum GCWR -lb (kg)Maximum TrailerWeight - lb (kg)2WD 3.0L 7140 (3239) 3500 (1588)4WD 3.0L 7300 (3311) 3500 (1588)Notes:– For high altitu
Safety chainsAlways connect the trailer’s safety chains to the hook retainers on thevehicle. To connect the trailer’s safety chains, cross the chains
• Turn off the speed control. The speed control may shut offautomatically when you are towing on long, steep grades.• Use the grade assist feature (au
Exceeding these limits may allow water to enter vehicle components:• Causing internal damage to the components.• Affecting driveability, emissions and
• For vehicles equipped with an automatic transmission, start the engineand allow it to run for five minutes at the beginning of each day andevery six
STARTINGPositions of the ignition1. Off— locks the gearshift leverand allows key removal.2. Accessory— allows the electricalaccessories such as the ra
WARNING: If you smell exhaust fumes inside your vehicle, haveyour dealer inspect your vehicle immediately. Do not drive if yousmell exhaust fumes.Impo
• Make sure the gearshift is in P(Park).If starting a vehicle with a manualtransmission:• Make sure the parking brake isset.• Press and hold the clutc
Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrument Cluster chapter for more informationregarding the warning
MILES (km) TO EThis displays an estimate of approximately how far you can drive withthe fuel remaining in your tank under normal driving conditions.Re
Do not crank the engine for more than 10 seconds at a time as starterdamage may occur. If the engine fails to start, turn the key to off andwait 30 se
the user to connect the system to a grounded 120 volt A/C electricalsource. The block heater system is most effective when outdoortemperatures reach b
become very hot and may result in an electrical shock or fire. Be sureto check for heat anywhere in the electrical hookup once the systemhas been oper
keeping the brakes from locking. Noise from the ABS pump motor andbrake pedal pulsation may be observed during ABS braking and thebrake pedal may sudd
The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned on) until theparking brake is released.
• Roll Stability Control™ (RSC威), which functions to help avoid avehicle roll-overWARNING: Vehicle modifications involving braking system,aftermarket
The AdvanceTrac威 with RSC威system includes a traction controloff button on the instrument panelbelow the climate control, a stabilitycontrol “OFF” ligh
During traction control events, the stability control light in theinstrument cluster will flash.If the traction control system is activated excessivel
Roll Stability Control™ (RSC威)Roll Stability Control (RSC威) may help to maintain roll stability of thevehicle during adverse maneuvers. RSC威 operates
AdvanceTrac威 with RSC威 FeaturesButtonfunctionsStabilitycontrollightRSC威/ESC/TractioncontrolStabilitycontrol“OFF”TrailerswayDefault atstart-upIlluminat
Your vehicle must be moving to calculate instantaneous fuel economy.When your vehicle is not moving, this function shows ↓, one or no barsilluminated.
sway is detected, the vehicle speed is too high and may be at or above aspeed at which trailer sway will grow continuously. This may cause thesystem t
PREPARING TO DRIVEWARNING: Utility vehicles have a significantly higher rolloverrate than other types of vehicles.WARNING: In a rollover crash, an unb
Note: For some markets, this feature will be disabled. If the fuse is notblown, perform the following procedure:1. Apply the parking brake, turn the i
provide consistent shift feel over the life of the vehicle. A new vehicle ortransmission may have firm and/or soft shifts. This operation isconsidered
N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D
O/D (overdrive mode) is automatically returned each time the engine isturned off.L (Low)• Provides maximum engine braking.• Will downshift to the lowe
Do not drive with your foot resting on the clutch pedal or use theclutch pedal to hold your vehicle at a standstill while waiting on ahill. These acti
3. Turn the ignition off.WARNING: Do not park your vehicle in Neutral, it may moveunexpectedly and injure someone. Use 1 (First) gear and set theparki
The RSS detects obstacles up to6 feet (1.8 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the
REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rearview camera system locatedon the liftgate provides a videoimage, which appears in therearview mirror or on
To reset the oil monitoring system to 100% after each oil change,perform the following:1. Press and release the SETUP button to display “OIL LIFE XXX%
Note: The default setting for the camera delay is off. Press the“Settings” button found on the navigation screen (if equipped) to set thecamera delay
Servicing• If the image comes on while the vehicle is not in R (Reverse), havethe camera inspected by your authorized dealer.• If the image is not cle
For best performance, the driver should drive the vehicle as parallel aspossible while passing a parking space. If driven too fast (above 18 mph[30 km
When you determine the vehicle is back far enough or you hear a solidtone from the reverse sensing system, bring the vehicle to a completestop and mov
• Exceeding a vehicle speed of 6 mph (10 km/h) during automaticsteering• Deactivating the AdvanceTrac威 system or the system has activated ona slippery
Why doesn’t APA position the vehicle where I want in the space?• The driver allows the vehicle to roll in the opposite direction of thetransmission (s
Driving with blind spot mirrorsBefore a lane change, check themain mirror first, then check theblind spot mirror. If no vehicles arepresent in the bli
Driving off-road with truck and utility vehicles4WD vehicles are specially equipped for driving on sand, snow, mud andrough terrain and have operating
• It often may be less risky to strike small objects, such as highwayreflectors, with minor damage to your vehicle rather than attempt asudden return
Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,
ZONE [XX] RESET = CHANGE (if equipped)For more information on the compass and compass set up, refer toElectronic compass in the Driver Controls chapte
Mud and waterIf you must drive through highwater, drive slowly. Traction orbrake capability may be limited.When driving through water,determine the de
Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should
Driving on snow and ice4WD vehicles have advantages over 2WD vehicles in snow and ice butcan skid like any other vehicle.Should you start to slide whi
Any modifications to a vehicle that raise the center of gravity can makeit more likely the vehicle will roll over as a result of a loss of control.For
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
Owner Guide portfolio in the glove compartment. In Canada, the card isfound in the Warranty Guide in the glove compartment.U.S. Ford, Mercury and Linc
This switch is located in the frontpassenger’s footwell, behind aflip-up cover, by the kick panelaccess cover.To reset the switch:1. Turn the ignition
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Not used (spare)2 15A Brake on/off switch3 15A SYNC威 module4 30
Fuse/RelayLocationFuse AmpRatingProtected Circuits15 10A Climate control16 15A Not used (spare)17 20A All lock motor feeds, Liftgaterelease, Liftglass
REAR RIGHT DOOR AJAR — Displayed when the rear right door isnot completely closed.PARK BRAKE ENGAGED — Displayed when the parking brake is set,the eng
Fuse/RelayLocationFuse AmpRatingProtected Circuits41 15A Driver/passenger door lockswitches, Automatic dimmingmirror, Compass, Ambientlighting, Moon r
The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected CircuitsA 80A Midi Electronic power steering module(EPAS)B 125A
Fuse/RelayLocationFuse AmpRatingProtected Circuits14 15A* Trailer tow turn lamps15 — Not used16 40A** Cooling fan 117 40A** Cooling fan 218 20A** ABS
Fuse/RelayLocationFuse AmpRatingProtected Circuits31F — Liftgate latch relay32 — Not used33 — PCM diode34 — Start diode35 10A* Run/start, Reverse lamp
Dissimilar spare tire/wheel informationWARNING: Failure to follow these guidelines could result in anincreased risk of loss of vehicle control, injury
3. Full-size dissimilar spare without label on wheelWhen driving with the full-size dissimilar spare tire/wheel, do not:• Exceed 70 mph (113 km/h)• Us
Stopping and securing the vehicle1. Park on a level surface, set theparking brake and activate hazardflashers.2. Place gearshift lever in P (Park)(aut
Remove the lug wrench from thejack in order to remove the sparetire from under the vehicle.Removing the spare tire or spare tire and tether (if equipp
5. Use the lug wrench to remove thelug nut from the spare tire tether.6. If not replacing the spare or flattire to the underbody storage area,raise wi
WARNING: If the vehicle slips off the jack, you or someone elsecould be seriously injured.WARNING: Do not attempt to change a tire on the side of thev
KEY COULD NOT PROGRAM — Displayed when an attempt is madeto program a spare key using two existing MyKeys. Refer to MyKey™ inthe Locks and Security ch
Before placing the jack under the vehicle, NOTE the jack locations:• FrontView shown from rear of front tire.Position the jack directly below theprotr
• RearView shown from forward of reartire. Position the jack directly belowthe stud on the rear trailing arm.3. Position the jack according to theguid
Never use the differentials as ajacking point.WARNING: To lessen therisk of personal injury, donot put any part of your bodyunder the vehicle while ch
Stowing the jack and tools• Make sure the jack is fullylowered.• Reclip the tools onto the jackmaking sure that the tools arefully contained by the cl
spare tire carrier has a built-in ratchet feature that will not allow you toovertighten. If the spare tire carrier ratchets with very little effort, t
Note: Inspect the wheel pilot holeprior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean r
Preparing your vehicleWhen the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a
1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery.2. Connect the other end of thepositive (+) cable to the
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.Note: In the illustration, the vehicle on the bottom i
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
CANCELLED BY OVER SPEED (if equipped)— Displayed when theactive park assist feature self cancels due to vehicle speed over thepreset limit allowed by
Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized
In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph
In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext
You are required to submit your warranty dispute to BBB AUTO LINEbefore asserting in court any rights or remedies conferred by CaliforniaCivil Code Se
You can get more information by calling BBB AUTO LINE at1-800-955-5100, or writing to:BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia
GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.
If your vehicle must be serviced while you are traveling or living in theMiddle East, contact the nearest authorized dealer. If the authorizeddealer c
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i
ACTIVE PARK FINISHED (if equipped) — May display when usingthe active park assist system. See Active park assist in the Drivingchapter for more inform
• Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, sid
• Spray Motorcraft威 Engine Shampoo and Degreaser (ZC-20) on allparts that require cleaning and pressure rinse clean. In Canada, useMotorcraft威 Engine
PLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authorized dealer.• For r
INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENSClean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth,
INTERIORFor fabric, carpets, cloth seats, safety belts and seats equipped with sideairbags:• Remove dust and loose dirt with a vacuum cleaner.• Remove
• Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl and plastics, or oil/petroleum-basedleathe
• Clean the surfaces using the steps outlined in the Cleaning section.• Ensure the leather is dry then apply a nickel-sized amount ofconditioner to a
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
Working with the engine on1. For vehicles equipped with an automatic transmission, set the parkingbrake and shift to P (Park). For vehicles equipped w
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.5L I4 engine1. Engine coolant reservoir2. Engine oil filler cap3. Automatic transmission dipstick (i
AUDIO SYSTEMSAM/FM single CD/MP3 satellite compatible sound systemWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and
3.0L V6 engine1. Engine coolant reservoir2. Air filter assembly3. Brake fluid reservoir4. Automatic transmission fluid dipstick5. Power distribution b
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
CHANGING THE WIPER BLADES1. Pull the wiper blade and armaway from the glass.2. Squeeze the locking tabs torelease the blade from the arm andpull the b
To replace the wiper blade:1. Grab the wiper arm with onehand close to the arm/blade jointand pull it as far away from theglass as possible. Do not us
• 2.5L I4 engine• 3.0L V6 engine6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil level is within the lower and
• 3.0L V6 engine• If required, add engine oil to the engine. Refer to Adding engine oilin this chapter.• Do not overfill the engine with oil. Oil leve
Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils certified for gasoline engines by the
BATTERYYour vehicle is equipped with aMotorcraft威 maintenance-freebattery which normally does notrequire additional water during itslife of service.If
WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
Maintenance and Specifications 287Engine compartment 289Engine oil 293Battery 297Engine coolant 299Fuel information 304Air filter(s) 321Part numbers 3
AM/FM Radio/ VOL (Power/Volume): Pressto turn the radio on/off. Turn theknob to increase/decrease volume.If the volume is set above a certainlevel and
• Refer to scheduled maintenance information for service intervalschedules.If the engine coolant has not been checked at the recommended interval,the
• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcoholand other liquids can cause en
Whenever coolant has been added, the coolant level in the coolantreservoir should be checked the next few times you drive the vehicle. Ifnecessary, ad
If you drive in extremely hot climates:• It is still necessary to maintain the coolant concentrationabove 40%.• NEVER decrease the coolant concentrati
When fail-safe mode is activatedYou have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be ab
WARNING: The fuel system may be under pressure. If you heara hissing sound near the fuel filler door (Easy Fuel™ “no cap”fuel system), do not refuel u
sensitive individuals, serious personal injury or sickness may result. Iffuel is splashed on the skin, promptly wash skin thoroughly with soapand wate
WARNING: The flow of fuel through a fuel pump nozzle canproduce static electricity, which can cause a fire if fuel ispumped into an ungrounded fuel co
3. Slowly insert the fuel filler nozzle fully into the fuel system, and leavethe nozzle fully inserted until you are done pumping. Pump fuel asnormal.
Flex fuel vehicle (FFV) fuel fill inletIf your vehicle is flex fuel capable, it will have a yellow bezel placed overthe fuel fill inlet.Choosing the r
To activate the autoset feature: Press MENU repeatedly until AUTOPRESET ON/OFF appears in the display. UseSEEK/TRACK toturn AUTO PRESET ON, and either
Do not be concerned if your enginesometimes knocks lightly. However,if it knocks heavily under mostdriving conditions while you areusing fuel with the
rating. These products have not been approved for your engine andcould cause damage to the fuel system. Repairs to correct the effects ofusing an afte
WARNING: Do not try to pry open or push open the EasyFuel™ system with foreign objects. This could damage the fuelsystem and its seal and cause injury
NOT accurate as a measure of fuel economy. We do not recommendtaking fuel economy measurements during the first 1,000 miles(1,600 km) of driving (engi
4. Subtract your initial odometer reading from the current odometerreading.5. Follow one of the simple calculations in order to determine fueleconomy:
• Combine errands and minimize stop-and-go driving.Maintenance• Keep tires properly inflated and use only recommended size.• Operating a vehicle with
• Have the items listed in scheduled maintenance informationperformed according to the specified schedule.The scheduled maintenance items listed in sc
government emission standards. The OBD-II system also assists yourauthorized dealer in properly servicing your vehicle. When the serviceengine soonind
indicate that the vehicle is not ready for I/M testing. To determine if thevehicle is ready for I/M testing, turn the ignition key to the on positionf
consume fluid. However, the fluid level should be checked if thetransmission is not working properly, i.e., if the transmission slips orshifts slowly
/ Play/Pause: Press toplay/pause a track when playing aCD.SEEK/TRACK: PressSEEK/TRACK to access theprevious/next track.CAT (Category) / FOLD (Folder):
The transmission fluid should be inthe zone, identified by the arrow inthis figure, if at normal operatingtemperature 185°F-200°F(85°C-93°C).High flui
prevent damage to your transmission. Before you recreational flat tow,your fluid level must be verified by an authorized dealer.This fluid level is wi
Changing the air filter element1. Release the clamps that secure the air filter housing cover.• 2.5L I4 engine• 3.0L V6 engine2. Pull the air filter h
All motor vehicles and their components were engineered and tested forreliable, regular driving. Long term storage under various conditions maylead to
vehicle fuel system whenever actual or expected storage periods exceed30 days. Follow the instructions on the additive label. The vehicle shouldthen b
• Check brake pedal operation. Drive the vehicle 15 ft (4.5 meters) backand forth to remove rust build up.• Check fluid levels (including coolant, oil
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord part name orequivalentFord part number /Ford SpecificationBrake fluid and (clutchfl
Item CapacityFord part name orequivalentFord part number /Ford SpecificationEngine oil(2.5L engine)5.3 quarts(5.0L)•Motorcraft威 SAE 5W-20Premium Synth
Item CapacityFord part name orequivalentFord part number /Ford SpecificationWindshield washer fluid Fill as requiredMotorcraft威 PremiumWindshield Wash
ENGINE DATAEngine 2.5L I4 Engine 3.0L V6 EngineCubic inches 152 183Required fuel 87 octane 87 octane or E85Firing order 1-3-4-2 1-4-2-5-3-6Ignition sy
SHUFFLE: Press SHUFFLE to switch on/off and begin/stop random play.The system will only shuffle the disc currently playing.Satellite Radio (if equippe
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C
Lifestyle•Ash cup/ smoker’s package •Navigation*•Cargo management accessories •Roof racks and carriers*•Cross bars •Rear bumper protector*•SUV camping
• Mobile communications systems may harm the operation of yourvehicle, particularly if they are not properly designed for automotiveuse.• To avoid int
FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP.
Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With
Ford Extended Service Plan3372011 Escape (204)Owners Guide, 1st PrintingUSA (fus)
FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is
GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?This guide describes the scheduled maintenance required for yourvehicle. Carefully following
MEMORY PRESETS (0–9): Thereare 30 available presets, 10 each forSAT1, SAT2 and SAT3. To savesatellite channels in your memorypresets, tune to the desi
If your message center is prematurely reset or becomes inoperative, youshould perform the oil change interval at six months or 5,000 miles(8,000 km) f
Genuine Ford parts and serviceWhen planning your maintenance services, consider your Ford andLincoln Mercury dealership for all your vehicle’s needs.G
Any adverse condition should be brought to the attention of your dealeror qualified service technician as soon as possible for the proper serviceadvic
Be sure to ask your Ford or Lincoln Mercury dealership service advisoror technician about the multi-point vehicle inspection. It’s acomprehensive way
Scheduled Maintenance Guide3442011 Escape (204)Owners Guide, 1st PrintingUSA (fus)
NORMAL SCHEDULED MAINTENANCE AND LOGFor your convenience, your vehicle is equipped with a message centerwhich determines the proper oil change service
Oil Change Service Interval* 1 23456789101112131415Change engine oil and filter • ••••••••••••••Rotate tires, inspect tire wear and measuretread depth
Perform the services noted in the following table at the specifiedtime/mileage (km) period either within 3,000 miles (5,000 km) of theOIL CHANGE REQUI
Every 150,000 miles(240,000 km)Change automatic transmission fluid and filter(except 5–speed TorqShift威 transmission) (filternot required on 6F35, 6F5
Maintenance schedule logDEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATIO
an audible prompt. Press OK while SONG ALERT is in the display andthe system will take you to the channel playing the desired song. Youcan save up to
DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOUR
DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOUR
SPECIAL OPERATING CONDITIONSIf you operate your Ford/Lincoln/Mercury vehicle primarily in one of themore demanding Special Operating Conditions listed
Extensive idling and/or low-speed driving for long distances as in heavycommercial use such as delivery, taxi, patrol car or liveryAs required – Chang
Operating in dusty conditions such as unpaved or dusty roadsInspect frequently, service asrequired– Replace cabin air filter (if equipped).– Replace e
Off-road operationInspect frequently, service asrequired– Inspect and lubricate steering linkage ball joints andU-joints (if equipped with grease fitt
Special operating condition logDEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VA
DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOUR
EXCEPTIONSIn addition, there are several exceptions to the Normal Schedule. Theyare listed below:Normal vehicle axle maintenance❑Rear axles and power
COOLANT CHANGE RECORDEngine coolant❑6 years or 100,000 miles (160,000 km) - change coolant (whichever comes first).❑After initial change - change cool
Note: you must be tuned to the specific channel you want tolock/unlock when using this feature.b. CHANGE PIN: Press OK when CHANGE PIN is displayed. T
Engine coolant change logDEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATI
AAccessory delay ...73Active Park Assist ...231AdvanceTrac ...214Air cleaner filte
Changing a tire ...253Child safety seats ...156attaching withtether straps ...162in f
coolant ...299fail-safe cooling ...303idle speed control ...297lubrication speci
IIgnition ...206, 329Illuminated visor mirror ...68Infant seats(see Safety seats) ...156Inspec
NNavigation system ...46OOctane rating ...309–310Oil (see Engine oil) ...293Overdrive ...
Safety ComplianceCertification Label ...330Satellite Radio Information ...43Scheduled Maintenance GuideNormal ScheduledMaintenan
Turn signal ...58UUniversal garage door opener...80USB port...39VVehicle Identifica
ALL SEATS (Occupancy mode, if equipped): Press SOUNDrepeatedly to reach the Occupancy mode setting. PressSEEK/TRACKto select and optimize sound for AL
Your vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicplayer to the in-vehic
7. Adjust the sound on your portable music player until it reaches thelevel of the FM station or CD by switching back and forth between theAUX and FM
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
Your vehicle may be equipped with aUSB port located on the instrumentpanel. This feature allows you toplug in media playing devices,memory sticks, and
CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C
CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
Satellite radio reception factors: To receive the satellite signal, yourvehicle has been equipped with a satellite radio antenna located on theroof of
Satellite radio electronic serial number (ESN): This 12–digitSatellite Serial Number is needed to activate, modify or track yoursatellite radio accoun
Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title information notavailable at this time on thischannel. Th
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1.Fan speed adjustment: Turn to select fan speed.2.RRear defroster: Press to activate/deactivat
7. : Distributes air through the instrument panel vents, demistervents, floor vents and rear seat floor vents (if equipped).8.: Distributes air throug
Operating tips• To reduce fog build-up on the windshield during humid weather,select(defrost) or (floor/defrost).• To reduce humidity build-up inside
Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti
DUAL AUTOMATIC TEMPERATURE CONTROL (IF EQUIPPED)1. AUTO/Driver temperature: Press to engage full automaticoperation. Select the desired temperature us
the vehicle through the vents. Turn to manually increase/decrease thefan speed. The manual fan speed setting will appear on the left side ofthe displa
14. Driver heated seat control (if equipped): Press toactivate/deactivate the driver heated seat. See Heated seats in theSeating and Safety Restraints
• Manual operation:1. Select MAX A/C.2. Selector .3. Select(recirculated air) to provide colder airflow.4. Set the temperature to 60°F (16°C).5. Set h
HEADLAMP CONTROLRotate the headlamp control to thefirst position to turn on theparking lamps.Rotate to the second positiontoturn on the headlamps.Rota
Autolamp delay system (if equipped)If your vehicle is equipped with autolamps, you can set the delay time tokeep the headlights on for up to three min
Flash-to-passPull toward you slightly to activateand release to deactivate.Daytime running lamps (DRL) (if equipped)Turns the low beam headlamps on wi
Note: If the battery is disconnected, discharged, or a new battery isinstalled, the dimmer switch requires re-calibration. Rotate the dimmerswitch fro
5. Locate the vertical adjuster onthe headlamp, then usea4mmsocket to turn the adjuster eithercounterclockwise (to adjust up) orclockwise (to adjust d
The map lamp controls (withoutmoon roof) are located on the domelamp. Press the button on eitherside of each map lamp to illuminatethe lamps. Press th
Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance
Ambient lighting (if equipped)Illuminates footwells, cupholders,the console bin and the console traywith a choice of several colors. Theambient lighti
Take your vehicle to a dealer for service if any of the above conditions ofunacceptable moisture are present.Using the right bulbsReplacement bulbs ar
Replacing headlamp bulbs1. Make sure the headlamp control is in the off position.2. Open the hood.3. Reach over the front bolster.4. Remove the bulb b
5. Carefully pull the bulb out of thesocket and push in the new bulb.6. Install the bulb socket into thelamp assembly and rotate clockwise.Replacing f
Replacing high-mount brake lamp bulbs1. Remove the two screws and movethe lamp assembly away from theliftgate.2. Remove the bulb holder from thelamp a
4. Pull bulb straight out of socketand push in the new bulb.5. Install the bulb socket into thelamp assembly and rotate clockwise.6. To install, caref
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
Rear window wiper/washer controlsFor rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select:2 — Normal spe
ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamps.Slide-on-rod featureThe visor will slide back and forthon
The compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antenna. Magneticor metallic objec
Using your vehicle as an ambulanceDo not use this vehicle as an ambulance.Your vehicle is not equipped with the Ford Ambulance PreparationPackage.DATA
6. The direction will display afterthe RESET control is released. Thezone is now updated.Compass calibration adjustmentPerform compass calibration in
5. Small storage trays and (if equipped) an ambient light control switch.WARNING: Use only soft cups in the cupholders. Hard objectscan injure you in
To prevent the fuse from being blown, do not use the power point(s)over the vehicle capacity of 12V DC/180W. If the power point or cigarlighter socket
release quickly. The window will open fully. Momentarily press the switchto any position to stop the window operation.Window lockThe window lock featu
Do not clean the housing or glass of any mirror with harshabrasives, fuel or other petroleum-based cleaning products.Note: If equipped with a rearview
Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re
3. Press and release SET +.4. Take your foot off the accelerator pedal.5. The indicatorlight on the instrument cluster will turn on.Note:• Vehicle spe
Turning off speed controlTo turn off the speed control, press OFF or turn off the ignition.Note: When you turn off the speed control or the ignition,
SYNC威 system hands-freecontrol feature (if equipped)Press briefly to use the voicecommand feature. You will hear atone and LISTENING will appear inthe
To open the moon roof: The moonroof is equipped with an automatic,one-touch, opening, closing andventing feature. Press and releasethe rear portion of
Note: EDR data is recorded by your vehicle only if a non-trivialcrash situation occurs; no data is recorded by the EDR undernormal driving conditions
The moon roof has a sliding shade that can be opened or closed whenthe glass panel is shut. To close the shade, pull it toward the front of thevehicle
Read the instructions completely before attempting to program theCar2U威 system. Because of the steps involved, it may be helpful to haveanother person
1. Firmly press the two outerCar2U威 system buttons for1–2 seconds, then release.2. Go to the garage to locate thegarage door opener motor and its“lear
The indicator light above the selected button will turn on to confirm thatthe Car2U威 system is responding to the button command.To program another rol
Switchposition 12345678 9101112Up, onor +LLLLLLLLLLLLMiddle,neutralor 0MMMMMMMM MMMMDown,offor–RRRRRRRRRRRRL=left; M=middle; R=right3. To input these
After successful programming, you will be able to operate your Car2U威system by pressing the button you programmed to activate the opener.The indicator
POSITIVE RETENTION FLOOR MATWARNING: Do not install additional floor mats on top of thefactory installed floor mats as they may interfere with theacce
WARNING: Make sure that the liftgate door and/or window areclosed to prevent exhaust fumes from being drawn into thevehicle. Exhaust fumes contain car
The larger, rearward, compartmentis for customer storage. To open, liftthe lid with the pull latch. The lidcan be removed to allow for flexiblestorage
To adjust the cross-bar (if equipped) position:1. Loosen the thumbwheel at bothends of the cross-bar (bothcross-bars are adjustable).2. Slide the cros
Ford or its vendors to receive this information, do not activatethe service. Ford Motor Company and the vendors it uses toprovide you with this inform
Be sure to check that the thumbwheels are tight each time load isadded, or removed from the roof rack, and periodically while traveling.Always ensure
KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unl
vehicle can be activated as a MyKey™. The key will remain restricteduntil MyKey™ is cleared. Any remaining keys are referred to as an“administrator ke
3. Press and hold the RESET button for two seconds until MARK THISAS RESTRICTED is displayed.4. Wait until KEY RESTRICTED AT NEXT START is displayed.M
4. Press and hold the RESET button for two seconds until ALL MYKEYSCLEARED is displayed.Check MyKey™ System StatusThe vehicle’s message center system
Note: For all vehicles with remote start installed, it is possible toprogram all original vehicle keys as MyKeys™, in which case, you willneed to use
Condition Potential CausesLost any key • For programming spare keys, refer to theProgramming spare keys section in this chapter.I accidentallyprogramm
AutolockThe autolock feature will lock all the doors, liftgate and liftgate windowwhen:• all doors are closed,• the ignition is in the on position,• y
1. The ignition must be off to beginsequence.2. Turn the ignition to the onposition.3. Press the power door unlockcontrol three times.4. Turn the igni
• the driver door is opened within 10 minutes of the ignition beingtransitioned to the off or accessory position.Note: The doors will not autounlock i
Commentaires sur ces manuels