Ford 2010 Explorer v.1 Manuel d'utilisateur

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 18Message center 21Entertainment Systems 39How to get going 39AM/FM stereo with

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield.• To improve the A/C cool down when the vehicle interior issign

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM(IF EQUIPPED)1. A/C control: Manually turns A/Con or off.2. Recirculation control: Coolsthe vehicle mo

5. DUAL (Single/dual electrictemperature control): Allows thedriver to have full control of thecabin temperature settings (single zone) or allows the

15. Fan Speed: Manually increasesor decreases the fan speed.16. EXT: Displays the outside airtemperature. It will remaindisplayed until the EXT contro

To allow side window defogging and demisting while warming up thevehicle cabin:1. Select.2. Select A/C.3. Set the temperature control to maintain comf

FLOOR CONSOLE CLIMATE CONTROLSControls the direction of the airflowto the rear of the vehicle.•directs air flow primarilythrough the console panelregi

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola

Fog lamp controlThe fog lamps can be turned ononly when the headlamp control isin the, or position andthe high beams are not turned on.Pull headlamp c

Flash to passPull the lever toward you toactivate. Release the lever todeactivate.PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument pa

To adjust the headlamps:1. Park your vehicle on a level surface about 25 feet (7.6 meters) awayfrom a vertical plain surface (3). Check your headlamp

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSDome/reading lampsThe dome lam

Cargo/reading lampsThe dome portion of the lamp orthe center light can be turned onwhen the panel dimmer control isrotated fully up or when a door iso

Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an

Replacing exterior bulbsCheck the operation of all the bulbs frequently.Replacing headlamp bulbsDo not touch the glass of a halogen bulb.1. Turn off t

Replacing front parking lamp/turn signal/sidemarker bulbs1. Turn off the headlamps and openthe hood.2. Remove three screws from theheadlamp assembly a

4. Rotate the bulb socketcounterclockwise and remove itfrom the lamp assembly.5. Pull the bulb straight out of thesocket.Reverse steps to reinstall bu

Replacing high-mount brakelamp bulb1. Remove the two screws and lampassembly away from the vehicle.2. Remove the bulb holder from thelamp assembly by

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

O (off) — Rear wiper and washer off.For rear wash cycle, rotate (and hold as desired) the rear wiper/washercontrol to eitherposition.From either posit

Slide on rod featureRotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage.Note: To stow the visor back intoth

WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may

Installing a garage door opener (if equipped)The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers:• Pla

WARNING: Use only soft cups in the cupholder. Hard objectscan injure you in a collision.Rear center console features (if equipped)The rear center cons

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe ba

To operate one touch down:• Press the switch completely downto the second detent and releasequickly. The window will openfully. Momentarily press thes

Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controls(except for the driver’s) pres

EXTERIOR MIRRORSPower side view mirrorsWARNING: Do not adjust the mirror while the vehicle is inmotion.The ignition must be in the accessory or on pos

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is

Enable/disable:To enable/disable the power running board feature, refer to Messagecenter in the Instrument Cluster chapter.• When this feature is disa

SPEED CONTROL (IF EQUIPPED)With speed control set, you can maintain a set speed without keepingyour foot on the accelerator pedal.WARNING: Do not use

Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed.Increasing spee

Service engine soon: The serviceengine soon indicator lightilluminates when the ignition is firstturned to the on position to checkthe bulb and to ind

Turning off speed controlThere are two ways to turn off the speed control:• Press the brake pedal. This will not erase your vehicle’s previously setsp

In CD mode (if equipped):• PressSEEK to select the next selection on the CD/USBor press and hold to forward or reverse through the CD/USB.In DVD mode

Press to activate phone mode or answer a phone call. Press andhold to end call or exit phone mode.Pressto scroll through various menus and selections.

To open the moon roof: Press andrelease the SLIDE control, the moonroof will open automatically. Pressthe switch again to stop the moonroof.To close t

HomeLink威Car2U威 Home AutomationSystemHomeLink姞 Wireless Control System (if equipped)The HomeLink威 Wireless Control System, located on the overheadcons

ProgrammingDo not program HomeLink威 with the vehicle parked in the garage.Note: Some vehicles may require the ignition switch to be turned to theacces

3. Firmly press and hold for five seconds and release theprogrammed HomeLink威 button up to two separate times to activate thedoor. If the door does no

Gate Operator & Canadian ProgrammingConsole mountVisor mountDuring programming, your hand-held transmitter may automatically stoptransmitting — no

Operating the HomeLink姞 Wireless Control SystemConsole mountVisor mountTo operate, simply press and release the appropriate HomeLink威 button.Activatio

Erasing HomeLink姞 buttonsConsole mountVisor mountTo erase the three programmed buttons (individual buttons cannot beerased):• Press and hold the two o

Brake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the on

Car2U姞 Home Automation System (if equipped)The Car2U威 Home AutomationSystem is a universal transmitterlocated in the driver’s visor thatincludes two p

• Fixed code garage door openers were produced prior to 1996. Fixedcode uses the same coded signal every time. It is manuallyprogrammed by setting DIP

2. Go to the garage to locate thegarage door opener motor and its“learn” button. You may need aladder to reach the unit and youmay need to remove the

Note: The Car2U威 system allows for three devices to be programmed. Ifyou need to change or replace any of the three devices after it has beeninitially

3. To input these positions into theCar2U威 system, simultaneouslypress all three Car2U威 systembuttons for a few seconds and thenrelease to put the dev

To erase programming on the Car2U威 system (individual buttons cannotbe erased), use the following procedure:1. Firmly press the two outsideCar2U威 syst

WARNING: Do not place any objects on the cargo area cover.They may obstruct your vision or strike occupants of the vehiclein the case of a sudden stop

REAR LIFTGATEThe liftgate area is only intended for cargo, not passengers. You can openand close the liftgate from outside the vehicle. It cannot be o

LUGGAGE RACKYour vehicle is equipped with a roof rack for transporting items on theexterior of the vehicle.The maximum recommended load tobe carried o

WARNING: Loaded vehicles, with a higher center of gravity,may handle differently than unloaded vehicles. Extraprecautions, such as slower speeds and i

Charging system: Illuminates when the battery is not charging properly.If it stays on while the engine is running, there may be a malfunctionwith the

KEYSOne key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency.Your keys are programmed to your v

Deactivating/activating autolockYour vehicle comes with the autolock feature enabled. There are fourmethods to enable/disable this feature:• Through y

Keyless entry keypad procedure1. Turn the ignition to the off position.2. Close all doors, the liftgate and liftgate window.3. Enter 5–digit entry cod

Power door unlock/lock procedureYou must complete Steps 1-5 within 30 seconds or the procedure willhave to be repeated. If the procedure needs to be r

Power door lock/unlock inhibit feature (if equipped)If the key is not in the ignition, all doors are closed, and the vehicle hasbeen locked using the

CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the

The remote entry system allows youto lock or unlock all vehicle doorsand liftgate, open the liftgatewindow without a key and activatethe panic alarm.T

Locking the doors/liftgate1. Press and release to lock all the doors and liftgate. The lamps willflash. Note: If any door, the liftgate or the liftgat

2. Press the SET control on thelower-center portion of theinstrument panel.3. Within five seconds, press onecontrol on the remote transmitterand then

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery.Note: Please refer to localreg

Low tire pressure warning:Illuminates when your tire pressureis low. If the light remains on atstart up or while driving, the tirepressure should be c

3. Turn the key from the 1 (off)position to 3 (on).4. Cycle eight times rapidly (within10 seconds) between the 1 (off)position and 3 (on). Note: Theei

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• open the liftgate

• If you program a code to a position that already contains a set code,the previously-set code will be erased.Erasing personal code1. Enter the factor

Your vehicle comes with two coded keys; additional coded keys may bepurchased from your authorized dealer. The authorized dealer canprogram your spare

Automatic disarmingSwitching the ignition to the on position with a coded key disarms thevehicle.• The theft indicator will illuminate for three secon

2. Turn the ignition from the 1 (off)position to the 3 (on) position. Keepthe ignition in the 3 (on) positionfor at least three seconds, but nomore th

SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting the front manual seat (if eq

AdvanceTrac威: Flashes when theAdvanceTrac威 with RSC威 system isactive. Illuminates solid when thesystem has been disabled (by thedriver or as a result

Using the manual lumbar support (if equipped)For more lumbar support, turn thelumbar support control toward thefront of vehicle.For less lumbar suppor

WARNING: To reduce the risk of possible serious injury: Do nothang objects off seat back or stow objects in the seatback mappocket (if equipped) when

Press the control to recline theseatback forward or rearward.Using the power lumbar support (if equipped)The power lumbar control is located on the ou

A position can be recalled:• in any gearshift position if the ignition is not in the on position.• only in P (Park) or N (Neutral) if the ignition is

Deactivating/activating the easy access/easy out featureThe easy entry/exit feature can be turned off or on through the vehiclemessage center (if equi

The heated seat control is located in the lower center of the instrumentpanel.To operate the heated seats:• Push control to activate.• Push again to d

Refer to Safety seats for children later in this chapter.WARNING: If the head restraint has been removed from aseating position to accommodate a high

To return the seat to the upright position (seats not equippedwith E-Z entry):1. Pull up on the handle, and rotatethe seatback until you hear a click,

3. If the seat is to be occupied, liftup on the head restraint until itlocks into its original position.WARNING: Before returning the seatback to its

Returning to the upright position from full lowered load floorpositionThe seatback cannot be returned to the upright position until the seat isreturne

High beams: Illuminates when thehigh beam headlamps are turned on.Key-in-ignition warning chime: Sounds when the key is left in theignition in the off

WARNING: Always return the seat to the fully latched positionbefore operating the vehicle.Returning the seat to the upright positionNote: To return th

WARNING: Before returning the seatback to its originalposition, make sure that cargo or any objects are not trappedbehind the seatback. After returnin

3rd row folding seat (if equipped)Before folding the third row seats,fold the head restraints down bypulling on the strap located underthe restraint.P

The control buttons are located onthe driver-side rear quarter trimpanel (accessible from the liftgatearea).Push the bottom portion of thecontrol butt

WARNING: Before returning the seatback to its originalposition, make sure that cargo or any objects are not trappedbehind the seatback. After returnin

The fact that the pretensioners or airbags did not activate for both frontseat occupants in a collision does not mean that something is wrong withthe

WARNING: Air bags can kill or injure a child in a child seat.NEVER place a rear-facing child seat in front of an active airbag. If you must use a forw

to the Warning lights and chimes section in the Instrument Clusterchapter. Routine maintenance of the Personal Safety System威 is notrequired.The Restr

WARNING: In a rollover crash, an unbelted person issignificantly more likely to die than a person wearing a safetybelt.WARNING: Each seating position

Combination lap and shoulder belts1. Insert the belt tongue into the proper buckle (the buckle closest tothe direction the tongue is coming from) unti

Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,

Automatic locking modeWhen to use the automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to

How to disengage the automatic locking modeUnbuckle the combination lap and shoulder belt and allow it to retractcompletely to disengage the automatic

Front safety belt height adjustmentYour vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shou

To adjust the comfort guide:1. Slip the shoulder belt into thebelt guide.2. Slide the guide up or down alongthe webbing so that the belt iscentered on

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war

The Belt-Minder威 feature uses two different warning chimes. During thefirst minute of activation, the warning chime will sound once everysecond. The r

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra

Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate

The driver and front passenger Belt-Minder威 features can bedeactivated/activated by performing the following procedure:Before following the procedure,

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

Locks and Security 150Keys 150Locks 150Anti-theft system 156Seating and Safety Restraints 166Seating 166Safety restraints 184Airbags 199Child restrain

Trip odometer: Registers the miles (kilometers) of individual journeys.• Standard instrument clusterPress the SELECT/RESET controlonce to switch from

WARNING: Never place your arm over the airbag module as adeploying airbag can result in serious arm fractures or otherinjuries.To properly position yo

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

• one or more impact and safing sensors.• a readiness light and tone.• diagnostic module.• and the electrical wiring which connects the components.• F

The front passenger sensing systemuses a ⬙passenger airbag off⬙ or⬙pass airbag off⬙ indicator which willilluminate and stay lit to remind youthat the

OccupantPass Airbag OffIndicator LampPassenger AirbagEmpty seat Unlit DisabledSmall child in childsafety seat or boosterLit DisabledSmall child with s

ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase,

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi

A difficulty with the system is indicated by one or more of the following:• The readiness light will eitherflash or stay lit.• The readiness light wil

automotive safety experts known as the Side Airbag Technical WorkingGroup. These recommended testing procedures help reduce the risk ofinjuries relate

STANDARD MESSAGE CENTER (IF EQUIPPED)Your vehicle’s message center allowsyou to configure/personalize certainvehicle options to suit your needs.The me

WARNING: If the sideairbag has deployed, theairbag will not function again.The side airbag system(including the seat) must beinspected and serviced by

WARNING: All occupants of the vehicle including the drivershould always wear their safety belts even when an airbag SRSand Safety Canopy威 system is pr

The Safety Canopy威 system, in combination with safety belts, can helpreduce the risk of severe injuries in the event of a significant side impactcolli

WARNING: If the Safety Canopy威 system has deployed, theSafety Canopy威 will not function again. The SafetyCanopy威 system (including the A, B and C pill

SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestr

Installing child safety seats with combination lap and shoulderbeltsIf needed, when installing some high back child restraints, the headrestraints of

AVERAGE FUEL XX.X MPG / (L/100km)Average fuel economy displays your average fuel economy in miles/gallonor liters/100 km.If you calculate your average

• Keep the buckle release button pointing up and away from the safetyseat, with the tongue between the child seat and the release button,to help preve

3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi

8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up

however the safety belt can still be used to attach the child seat. Forforward-facing child seats, the top tether strap must also be attached tothe pr

The LATCH anchors for child seatinstallation are located at the rearsection of the second row seatbetween the cushion and seatback.The LATCH anchors a

WARNING: Depending on where you secure a child restraint,and depending on the child restraint design, you may blockaccess to certain safety belt buckl

Attaching child safety seats with tether strapsMany forward-facing child safety seats include a tether strap whichextends from the back of the child s

Perform the following steps to install a child safety seat with tetheranchors:1. Route the tether strap under the head restraint and between the headr

3. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theeven

Booster seats position a child so that vehicle lap/shoulder safety belts fitbetter. They lift the child up so that the lap belt rests low across the h

• Compass zone adjustment• Compass calibration adjustmentSYSTEM CHECK HOLD RESETPress and hold the SELECT/RESET stem to select system check whenthis i

Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air

The cold inflation pressure should never be set lower than therecommended pressure on the Safety Compliance Certification Label orTire Label.When weat

2. Press the SELECT/RESET stem for the next setup menu item or waitfor more than four seconds to return to the info menu.ENGLISH / SPANISH / FRENCH /

TIRE CAREInspecting your tires and wheel valve stemsPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones

WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressur

WARNING: Only use replacement tires and wheels that are thesame size, load index, speed rating and type (such as P-metricversus LT-metric or all-seaso

It is recommended that the two front tires or two rear tires generally bereplaced as a pair.The tire pressure sensors mounted in the wheels (originall

Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your

Note: If your tires show uneven wear ask an authorized dealer to checkfor and correct any wheel misalignment, tire imbalance or mechanicalproblem invo

4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new

8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n

13. Maximum Permissible Inflation Pressure: Indicates the tiremanufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

2. Press and hold the SELECT/RESET stem to turn park aid on or off.3. Press the SELECT/RESET stem for the next setup menu item or waitfor more than fo

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti

When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.

Low Tire PressureWarning LightPossible cause Customer Action RequiredFlashing WarningLightSpare tire in use Your temporary spare tire is inuse. Repair

SNOW TIRES AND CABLESWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. The use ofnon-recommende

your vehicle, familiarize yourself with the following terms for determiningyour vehicle’s weight ratings, with or without a trailer, from the vehicle’

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

Most geographic areas (zones) have a magnetic north compass point thatvaries slightly from the northerly direction on maps. This variation is fourdegr

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400

TRAILER TOWINGTrailer towing with your vehicle may require the use of a trailer towoption package.Trailer towing puts additional loads on your vehicle

4x2GCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.0L SOHC Class

4X4 and AWDGCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.6L* C

Class III Trailer Hitch Safety ChainLoops can be used as recoveryhooks.Do not attach safety chains to the bumper.Trailer brakesElectric brakes and man

Driving while you towWhen towing a trailer:• To ensure proper “break-in” of powertrain components, do not trailertow during the first 1,000 miles (1,6

• If you will be towing a trailer frequently in hot weather, hillyconditions, at GCWR, or any combination of these factors, considerrefilling your rea

Note: Put your climate control system in recirculated air mode toprevent exhaust fumes from entering the vehicle. Refer to the Climatecontrols chapter

2. Press and release the SELECT/RESET stem to scroll through theinformation menu until the message center displays HOLD RESET FORSETUP MENU.3. Press a

STARTINGPositions of the ignition1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accesso

WARNING: If you smell exhaust fumes inside your vehicle, haveyour dealer inspect your vehicle immediately. Do not drive if yousmell exhaust fumes.Impo

• Make sure the gearshift is in P(Park).3. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminate. See

Starting the engine1. Turn the key to 3 (on) withoutturning the key to 4 (start). If thereis difficulty in turning the key,rotate the steering wheel u

ENGINE BLOCK HEATER (IF EQUIPPED)An engine block heater warms the engine coolant which aids in startingand allows the heater/defroster system to respo

• Be sure that areas where the vehicle is parked are clean and clear ofall combustibles such as petroleum products, dust, rags, paper andsimilar items

Four-wheel anti-lock brake system (ABS)Your vehicle is equipped with an Anti-lock Braking System (ABS). Thissystem helps you maintain steering control

Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.ADVANCETR

WARNING: If a failure has been detected within theAdvanceTrac威 with RSC威 system, the ⬙sliding car⬙ iconwillilluminate steadily. Verify that the Advanc

• Some messages can be acknowledged and reset by pressing theSELECT/RESET stem. This allows you to use the full message centerfunctionality by clearin

When AdvanceTrac威 with RSC威 performs a normal system self-check,some drivers may notice a slight movement of the brake, and/or arumble, grunting, or g

Electronic Stability Control (ESC)Electronic Stability Control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa

The Roll Stability Control™ system may be deactivated in certainsituations. See the Switching Off AdvanceTrac威 with RSC威 sectionfollowing.Switching Of

WARNING: Trailer sway control does not prevent a trailer fromswaying, it mitigates the sway from increasing once it hasoccurred. If you are experienci

• Heavy or uneven steering efforts may be caused by low power steeringpump fluid level. Check for low power steering pump fluid level beforeseeking se

WARNING: Loaded vehicles, with a higher center of gravity,may handle differently than unloaded vehicles. Do not overloadyour vehicle and use extra pre

WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your author

R (Reverse)With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Re

3 (Third)Transmission operates in third gear only.Used for improved traction on slippery roads. Selecting 3 (Third)provides engine braking.2 (Second)U

P (Park)This position locks the transmissionand prevents the rear wheels fromturning.To put your vehicle in gear:• Press the brake pedal• Start the en

TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressuresensor is malfunctioning, or your spare tire is in use. For moreinformation on how the syst

D (Drive) without OverdriveOverdrive can be deactivated bypressing the transmission controlswitch on the side of the shift lever.• This position allow

• Allows upshifts by moving gearshift lever.• Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds

WARNING: Certain add-on devices such as large trailer hitches,bike or surfboard racks and any device that may block thenormal detection zone of the re

Audible WarningsDistance to Object WarningSpeed above 2.5 mph (4 km/h)up to 1.6 feet (.5 meters) Solid1.6 feet (.5 meters) to 3.1 feet(1 meter)Fast be

If the vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement

4X4 HIGH (4WD High) - Provides locked four-wheel drive power to allfour wheels. This mode is not intended for use on dry pavement. Thismode is appropr

Normal operation (4.0L engine vehicles only)The AWD system is always active and requires no driver input. It iscapable of handling all road conditions

Maintain steering wheel control at all times, especially in rough terrain.Since sudden changes in terrain can result in abrupt steering wheelmotion, m

WARNING: Vehicles with a higher center of gravity such asutility and four-wheel drive vehicles handle differently thanvehicles with a lower center of

Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,

Customer Assistance 333Reporting safety defects (U.S. only) 339Reporting safety defects (Canada only) 339Cleaning 340Maintenance and Specifications 34

OPTIONAL MESSAGE CENTER (IF EQUIPPED)Your vehicle’s message center allowsyou to configure/personalize certainvehicle options to suit your needs.The me

ParkingOn some 4WD vehicles, when the transfer case is in the N (Neutral)position, the engine and transmission are disconnected from the rest ofthe dr

Mud and waterIf you must drive through highwater, drive slowly. Traction orbrake capability may be limited.When driving through water,determine the de

Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should

Driving on snow and iceAWD and 4WD vehicles have advantages over 2WD vehicles in snow andice but can skid like any other vehicle.Should you start to s

Any modifications to a vehicle that raise the center of gravity can makeit more likely the vehicle will roll over as a result of a loss of control.For

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co

FUEL PUMP SHUT-OFF SWITCHFUELRESETThe fuel pump shut-off switch is a device intended to stop the electricfuel pump when your vehicle has been involved

FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth

Passenger compartment fuse panelThe fuse panel is located below theinstrument panel on the driver’sside.To remove a fuse use the fuse puller tool prov

Refer to UNITS later in this section to switch the display from Metric toEnglish.MILES (km) TO EThis displays an estimate of approximately how far you

Fuse/RelayLocationFuse AmpRatingProtected Circuits5 5A Moon roof, Door lock switchillumination, Auto dimming rearview mirror6 20A Liftglass release mo

Fuse/RelayLocationFuse AmpRatingProtected Circuits21 — Not used22 15A Brake switch, Bi-color stop lamps,High-mount brake lamp, All turnlamps23 15A Int

The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 50A** Battery feed 2 (passengercompartment fuse panel)

Fuse/RelayLocationFuse AmpRatingProtected Circuits13 30A** Trailer tow battery charger14 30A** Memory seats40A** Non-memory seats15 40A** Rear defrost

Fuse/RelayLocationFuse AmpRatingProtected Circuits40 15A* Fan clutch, Positive crackcaseventilation (PCV) valve, A/C clutchrelay41 15A* Satellite radi

CHANGING THE TIRESIf you get a flat tire while driving:• do not brake heavily.• gradually decrease the vehicle’s speed.• hold the steering wheel firml

A dissimilar spare tire/wheel is defined as a spare tire and/or wheel thatis different in brand, size or appearance from the road tires and wheelsand

The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following:• Handling, stability and braking performance• Comfort and

Location of the spare tire and toolsThe spare tire and tools for your vehicle are stowed in the followinglocations:Tool LocationSpare tire Under the v

Removing the spare tireDo not use an impact wrench on the winch drive nut. This willdamage the spare tire winch.1. Open the cover from the carpeting o

FUEL ECONOMY MPG (L/km)This displays instantaneous fuel economy as a bar graph ranging from ↓poor economy to ↑ excellent economy.Your vehicle must be

3. Turn the wrenchcounterclockwise until the tire islowered to the ground and the cablehas slack. When turning the wrench,make sure that it does not s

Note: Passengers should not remain in the vehicle when the vehicle isbeing jacked.1. Block the wheel that is diagonallyopposite of the flat tire using

5. Position the jack according to theillustrated guides and turn the jackhandle clockwise until the tire is amaximum of 1 inch (25 mm) off theground.N

9. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torquespecifications later in this chapterfor the proper lu

Re-stowing the jack and tools1. Unblock the wheels.2. Stow the wheel ornament (if removed) in a safe location in the vehicle(such as the glove box or

Note: Inspect the wheel pilot holeprior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean r

Preparing your vehicleWhen the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

4. Make the final connection of the negative (-) cable to the ground studlocated toward the front of the vehicle (forward of the battery) on theradiat

Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.

4. DOOR AJAR5. EXTERIOR LAMP6. BRAKE FLUID LEVEL7. PARK BRAKE8. FUEL LEVEL AND DISTANCE TO EMPTYAWD AUTO / LOCKED (if equipped)This feature disables/e

4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery.After the disabled vehicle has been started and the jumper

WRECKER TOWINGNote: Turn off the power running boards (if equipped) prior topreparing the vehicle for towing. Refer to Power deployable runningboards

On 4x4/AWD vehicles, it is required that your vehicle be towed with awheel lift and dollies or flatbed equipment with all the wheels off theground.If

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

If your vehicle must be serviced while you are traveling or living inCentral America, the Caribbean, or the Middle East, contact the nearestauthorized

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

Press the RESET button to turn autounlock on or off.RUNNING BRDS (if equipped)This feature automatically deploys the side running boards for easyentry

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent qu

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

4.6L V8 ENGINEPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authorized

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32-A),available from your au

If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows:1. Wipe up spilled liqui

LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• For routine cleaning, wipe the surface wit

Motorcraft Premium Glass Cleaner (Canada only) (CXC-100)Motorcraft Premium Liquid Wax (ZC-53-A)Motorcraft Premium Windshield Washer Concentrate (U.S.

SERVICE RECOMMENDATIONS• Use the scheduled maintenance information to track routineservice.• Use only recommended fuels, lubricants, fluids and servic

Working with the engine on1. Set the parking brake and shift to P (Park).2. Block the wheels.WARNING: To reduce the risk of vehicle damage and/orperso

Usually, when something affects the compass readings, the compass willcorrect itself after a few days of operating your vehicle in normalconditions. I

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.0L V6 engine1. Engine oil filler cap2. Engine oil dipstick (out of view)3. Brake fluid reservoir4. P

4.6L V8 engine1. Air filter assembly2. Engine oil filler cap3. Engine oil dipstick4. Brake fluid reservoir5. Power distribution box6. Battery7. Power

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas

4. To attach the new wiper to thewiper arm, align the cross pin andkeyway (denoted with the arrows)and firmly press the wiper bladeinto the wiper arm

• 4.6L V8 engine6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil level is between the lower and upper holes, t

• 4.6L V8 engine• Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized dealer.7. Put the

Engine Oil Recommendations4.0L V6 EngineLook for this certificationtrademark.Use SAE 5W-30 engine oilOnly use oils “Certified For Gasoline Engines” by

4.6L 3V V8 EngineLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by the AmericanPetroleum

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If

HOLD RESET IF NEW OILTo reset the oil monitoring system to 100% after each oil change(approximately 7,500 miles [12,000 km] or six months) perform the

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

• 4.0L V6 engine• 4.6L V8 engine• The engine coolant should be at the FULL COLD level or within theCOLD FILL RANGE as listed on the engine coolant res

Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservo

WARNING: To reduce the risk of personal injury, make sure theengine is cool before unscrewing the coolant pressure relief cap.The cooling system is un

Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut

What you should know about fail-safe cooling(4.6L V8 engine only)If the engine coolant supply is depleted, this feature allows the vehicle tobe driven

When fail-safe cooling mode is activatedYou have limited engine power when in the fail-safe mode, so drive thevehicle with caution. Remember that the

WARNING: Automotive fuels can cause serious injury or deathif misused or mishandled.WARNING: Gasoline may contain benzene, which is acancer-causing ag

WARNING: When refueling always shut the engine off andnever allow sparks or open flames near the filler neck. Neversmoke while refueling. Fuel vapor i

REMOVE OBJECTS NEAR PASS SEAT — Displayed when objectsare by the passenger seat. After the objects are moved away from theseat, if the warning stays o

Easy Fuel™ “no cap” fuel systemYour fuel tank is equipped with an Easy Fuel™ “no cap” fuel fillersystem. This allows you to simply open the fuel fille

WARNING: The fuel system may be under pressure. If you heara hissing sound near the fuel filler door (Easy Fuel™ “no cap”fuel system), do not refuel u

Fuel qualityIf you are experiencing starting, rough idle or hesitation driveabilityproblems, try a different brand of unleaded gasoline. If the proble

Refilling with a portable fuel containerWith the Easy Fuel™ “no cap” fuel system, use the following directionswhen filling from a portable fuel contai

ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform

Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers).2. Each time you fill the tan

• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between the top gears occurs. Unnecessaryshifting of this type co

EPA fuel economy estimatesEvery new vehicle should have a sticker on the window called theMonroney Label which contains EPA fuel economy estimates. Co

WARNING: Exhaust leaks may result in entry of harmful andpotentially lethal fumes into the passenger compartment.Do not make any unauthorized changes

If the service engine soon indicator remains on, have your vehicleserviced at the first available opportunity. Although some malfunctionsdetected by t

BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is lowand the brake system should be inspected immediately. Refer to Brakefluid in the Mainten

POWER STEERING FLUIDCheck the power steering fluid. Refer to scheduled maintenanceinformation.1. Start the engine and let it rununtil it reaches norma

Refer to your scheduled maintenance information for scheduledintervals for fluid checks and changes. Your transmission does notconsume fluid. However,

DRIVELINE UNIVERSAL JOINT, DRIVESHAFT AND SLIP YOKEWARNING: Turn off the power running boards, if equipped,before working under the vehicle, jacking o

Changing the air filter element• 4.0L Engine• 4.6L Engine1. Release the clamps that secure the air filter housing cover.2. Carefully separate the two

MOTORCRAFT PART NUMBERSComponent 4.0L V6 engine 4.6L 3V V8 engineAir filter element FA-1695 FA-1780Fuel filter FG-1083 FG-1083Battery BXT-65-650 BXT-6

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord Part Name orequivalentFord Part Number / FordSpecificationBrake fluidBetween MINand

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationEngine coolant(4.0L engine withoutauxiliary climatecontrol)12.2 quarts(11.

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationEngine oil(4.0L engine)5.0 quarts(4.7L)•Motorcraft SAE5W-30 PremiumSynthet

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationAutomatictransmission(5R55S) fluid12.7 quarts(12.0L)3MotorcraftMERCON威 VAT

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationFuel tank22.5 gallons(85.2L)——1Add the coolant type originally equipped in

AUDIO SYSTEMSQuick start — How to get goingWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly

ENGINE DATAEngine 4.0L V6 engine 4.6L 3V V8engineCubic inches 245 281Required fuel 87 octane 87 octaneFiring order 1-4-2-5-3-6 1-3-7-2-6-5-4-8Ignition

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

Peace of mindKeyless entry keypadRemote startVehicle security systemsLocking gas plug for capless fuel systemWheel locksFor maximum vehicle performanc

FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan3972010 Explorer (exp)Owners Guide (own2002), 1st PrintingUSA (fus)

AAccessory delay ...124AdvanceTrac ...278Air cleaner filter ...382–384Air conditioning ...

Child safety seats - boosterseats ...229Cleaning your vehicleengine compartment ...342instrument pa

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

Listening to satellite radio (if equipped)1. If the audio system is turned off,press VOL-PUSH to turn the radioon. Turn VOL-PUSH to adjust thevolume.N

idle speed control ...359lubrication specifications ...385refill capacities ...385service points ...

Hood ...349How to get going ...39IIgnition ...270, 390Illumina

Oil (see Engine oil) ...354PParking brake ...277Parts (see Motorcraft parts) ...384Passenger OccupantClassifi

SecuriCode keyless entrysystem ...161SecuriLock passive anti-theftsystem ...

WWarning lights (see Lights) ...12Washer fluid ...352Water, Driving through ...304Windows ...

For a single CD system, if a discis not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the

While in folder mode, pressFOLDER to access the nextfolder on MP3 discs, if available.Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inth

AM/FM Single CD/MP3 satellite compatible sound system(if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and

In CATEGORY MODE, press / to scroll through the list ofavailable SIRIUS channel Categories (Pop, Rock, News, etc.). Refer toCategory Mode under Menu f

• DELETE SONG: Press OK to delete a song from the system’smemory. Press/ to cycle through the saved songs. When thesong appears in the display that yo

To activate, press MENU repeatedly until RBDS (ON/OFF) appears inthe display. Use / / SEEK to toggle RBDS ON/OFF. WhenRBDS is OFF, you will not be abl

TRACK/FOLDER MODE: Available only on MP3 discs in CD mode.In track mode, pressSEEK, SEEK to scroll through all tracks onthe discIn folder mode, pressS

6. / (Play/Pause): Thiscontrol is operational in CD andDVD mode (if equipped). When aCD or DVD is playing in the FES system, press this control to pla

PRESET # SAVED appears in the display. You can save up to 18 stations,six in AM, six in FM1 and FM2.In satellite radio mode (if equipped), there are 1

Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti

16. CD: Press to enter CD/MP3mode. If a CD/MP3 is already loadedinto the system, CD/MP3 play willbegin where it ended last. If no CD is loaded, NO DIS

Accessory delay: Your vehicle is equipped with accessory delay. Withthis feature, the window switches, radio and moon roof (if equipped)may be used fo

• SAVE SONG: Press OK to save the currently playing song’s title inthe system’s memory. (If you try to save something other than a song,CANT SAVE will

AUTOSET: Press MENU until the display reads AUTOSET. Autosetallows you to set the strongest local radio stations without losing youroriginal manually

The default setting is off; increasing your vehicle speed will not changethe volume level.Adjust 1–7: Increasing this setting from 1 (lowest setting)

If your vehicle is equipped with a Family Entertainment System (FES)please refer to the Family Entertainment DVD system later in thischapter.If your v

Note: In track mode, all tracks on the current disc will shuffle inrandom order. In MP3 folder mode, the system will randomly play alltracks within th

Press and hold to hear a brief sampling of the next channels. Press againto stop.In CATEGORY MODE, press SCAN to hear a brief sampling of thechannels

18. (CD eject): To eject a discfrom the system, press . Selectthe correct slot number usingmemory presets 1–6. When ready, the system will eject the d

Required equipment:1. Any portable music player designed to be used with headphones2. An audio extension cable with stereo male 1/8 in. (3.5 mm)connec

Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance

5. For safety reasons, connecting or adjusting the settings on yourportable music player should not be attempted while the vehicle ismoving. Also, the

• Station overload: When you pass a broadcast tower, a stronger signalmay overtake a weaker one and play while the weak station frequencyis displayed.

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m

Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The

Your vehicle may be equipped with a Family Entertainment System(FES) which allows you to listen to audio CDs, MP3 discs, watch DVDsand to plug in and

Note (navigation-based radiosystems only): Whenadiscisinserted, the FES switches todual-play mode–rear speakers turn off, and headphones turn on. Tosw

Note (navigation-based radiosystems only): Whenadiscisinserted, the FES switches todual-play mode–rear speakers turn off, and headphones turn on. Tosw

Your vehicle is not equipped with the Ford Ambulance PreparationPackage.NOTICE TO OWNERS WITH 20 INCH WHEELS AND TIRESWhen equipped with 20 inch wheel

3. Connect an auxiliary audio/videosource by connecting RCA cords(not included) to the RCA jacks onthe left hand side of the system.• Yellow (1) — vid

4. Press MEDIA to change the audio source of the active channel (A orB). The audio source will be shown on the display. You may change theactive chann

Using wired headphones (not included):WARNING: Do not leave children unattended in the vehicle anddo not let children operate the system while unsuper

DVD player controls1. Headphone control A/B: Whilein Dual Play mode, press to selecteither the A or B headphone source.Then press MEDIA to select thed

4. (Fast forward): Press andrelease for the next chapter ortrack. Press and hold to forwardsearch a DVD, Video CD, or FES CD in DVD/CD mode.5./ (Play/

11. / (Headphones/Speakers): Press once for Dual Play(Headphone mode- the rear speakers are muted) and press again forSingle Play (same media playing

Remote controlUnless otherwise stated, all operations can be carried out with theremote control. Always point the remote control directly at the playe

7. VOL (Volume): When in Single Play, press to increase ( )ordecrease () the volume over all speakers. When in Dual Play, press toincrease () or decre

21. LANGUAGE (DVD dependent): Press to select the desiredlanguage.22. ENTER: Press to select the highlighted menu option.23. ILLUMINATION: Press to il

HeadphonesWireless headphonesWARNING: The driver should never use the headphones whiledriving the vehicle. Using headphones may prevent the driverfrom

• how far (if at all) the driver was depressing the acceleratorand/or the brake pedal;• how fast the vehicle was traveling;• where the driver was posi

To install the batteries, remove the screw at the bottom of the cover.Then, lightly press down on top and slide the cover off.When replacing the batte

To operate the headphones:• Press POWER on the ear piece to turn on the headphones. A redindicator light will illuminate indicating the headphones are

Wired headphonesWARNING: Do not leave children unattended in the vehicle anddo not let children operate the system while unsupervised. Ifwired headpho

Single Play: Single play consists of all occupants in the vehicle listeningto the same playing media over the front and rear speakers. When theDVD sys

Press MEDIA to change the audiosource for Channel A. Thisinformation will display on the DVDsystem screen.Press the Headphone Control buttonB to chang

Press MEDIA to change the audiosource for Channel A. Thisinformation will display on the DVDsystem screen.Press the Headphone Control buttonB to chang

Menu modePress MENU once on the DVD system to access the DVD disc menu ifavailable.Press MENU twice to access the DVD set-up menu and the followingfea

You can select from: WIDE, LETTERBOX or PAN SCAN. Once you havemade your selection, press ENTERto confirm. The LCD screen displaywill immediately chan

Once you have made your selection,press ENTER to confirm. This isdisc dependent.Audio CDsTo play audio CDs on your DVD system:1. Ensure that the vehic

4. The folder, track and elapsedtime will appear in the status bar.The screen will list the Artist, Title,Album and File Name.COMP (Compression):Compr

CELL PHONE USEThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri

CD, MP3 and CD player care• Handle discs by their edges only. Never touch the playing surface.• Do not expose discs to direct sunlight or heat sources

4. Use the DVD bezel controls to:Press to play or pause a DVD.Press to stop or eject a DVD.Press and release to go to theprevious chapter. Press and h

2. Press the right cursor button. TheDVD will advance one frame. Eachpress of the right cursor button willadvance the DVD video by oneframe.Headphone/

Audio displaysYour DVD system interacts closely with the front audio system. Statusmessages will appear in the radio display showing the DVD status. S

When the DVD system is ON, youcan then press the memory presetcontrols 2 and 4 simultaneously totoggle between Single Play and Dual Play. In Single Pl

Safety informationWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers us

Do not operate video games or video equipment if the power cordsand/or cables are broken, split or damaged. Carefully place cords and/orcables where t

Temperature extremesWhen the vehicle is parked under direct sunlight or in an extremely coldplace for a long period of time, wait until the cabin temp

Compatibility with aftermarket audio systems(headphone only mode)When the Family Entertainment System (FES) detects that the originalradio supplied by

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele