Ford 2010 Fusion Hybrid v.3 Manuel d'utilisateur

Introduction 4Instrument Cluster 18Warning lights and chimes 18Gauges 25Message center 35Entertainment Systems 51AM/FM stereo with CD/MP3 51Auxiliary

Question AnswerWhy does it take a long timebefore the engine shuts down?There are several reasons theengine stays on for an extendedamount of time whe

To open the moon roof:The moon roof is equipped with anautomatic, one-touch, expressopening, closing and venting feature.Press and release the rear po

To vent:• To tilt the moon roof into the vent position (when the glass panel isclosed), press and release the front portion of the control.• To close

KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unl

POWER DOOR LOCKS• Press thecontrol to unlock alldoors.• Press thecontrol to lock alldoors.Smart locksThis feature attempts to help prevent you from lo

Deactivating/activating autolock featureYour vehicle comes with the autolock features activated; there are fourmethods to enable/disable this feature:

4. Press and hold the 3 • 4. While holding the 3 • 4pressthe7• 8.5. Release the 7 • 8.6. Release the 3 • 4.The user should receive a horn chirp to ind

1. Place the key in the ignition andturn the ignition to the on position.2. Press the power door unlockcontrol on the door panel threetimes.3. Turn th

CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the

To open the luggage compartmentdoor (lid) from within the luggagecompartment, pull the illuminated“T” shaped handle and push up onthe trunk lid. The h

REMOTE ENTRY SYSTEMThe Integrated Keyhead Transmitter (IKT) complies with part 15 of theFCC rules and with RSS-210 of Industry Canada. Operation is su

Question AnswerWhat is the fan noise I hear fromthe rear of my hybrid?The fan noise comes from a fanlocated inside the high voltagebattery. This fan t

2. Press and release again within five seconds to unlock all the doors.The remote entry system activates the illuminated entry feature; thisfeature tu

Replacing the batteryThe integrated keyhead transmitter uses one coin type three-volt lithiumbattery CR2032 or equivalent.To replace the battery:1. Tw

The illuminated entry system will turn off the lights if:• the ignition is turned to the on position,• the Integrated Keyhead Transmitter lock control

1. Place the key in the ignition andturn the ignition to the 3 (on)position.2. Press the power door unlockcontrol on the door panel threetimes.3. Turn

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• open the trunk.Th

The anti-scan feature will turn off after:• one minute of keypad inactivity.• pressing thecontrol on the remote entry transmitter portion ofyour Integ

key chain may cause vehicle starting issues. You need to prevent theseobjects from touching the coded IKT while starting the engine. Theseobjects will

The theft indicator will illuminate for three seconds and then go out. Ifthe theft indicator stays on for an extended period of time or flashesrapidly

Please read and understand theentire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition.2. Turn the igniti

PERIMETER ALARM SYSTEMThe perimeter anti-theft system will help protect your vehicle fromunauthorized entry.If there is any potential perimeter anti-t

Question AnswerHow long will my high voltagebattery last? Does it needmaintenance?The high voltage battery system isdesigned to last the life of theve

Disarming the systemYou can disarm the system by any of the following actions:• Unlock the doors by using the remote entry transmitter portion ofyour

SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Using the manual recline functionWARNI

WARNING: Do not pile cargo higher than the seatbacks toreduce the risk of injury in a collision or sudden stop.WARNING: Always drive and ride with you

Move the switch in the direction ofthe arrows to raise or lower the rearportion of the seat cushion.Press the switch in the direction ofthe arrows to

Heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cordinjur

REAR SEATSNote: Do not block the air inlet at the front facing of the rear seatcushion. The air needs to be able to flow through the air inlet without

To adjust the head restraint, do the following:1. Raise the head restraint bypulling up on the head restraint.2. Lower the head restraint bypressing a

DATA RECORDINGService Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehi

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Insert and p

To reinstall the adjustable head restraint, do the following:1. Insert the two stems into theguide sleeve collars.2. Push the head restraint downuntil

Seat-mounted cup holders and armrest storage compartmentTo access the cup holders, fold thearmrest down.WARNING: Use only soft cups in the cup holder.

How does the Personal Safety System work?The Personal Safety System can adapt the deployment strategy of yourvehicle’s safety devices according to cra

to the airbag when it begins to inflate. For some occupants, this occursbecause they are initially sitting very close to the airbag. For otheroccupant

Front safety belt energy management retractorsThe front outboard safety belt energy management retractors allowwebbing to be pulled out of the retract

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until

movement. For example, if the driver brakes suddenly or turns a cornersharply, or the vehicle receives an impact of approximately 5 mph(8 km/h) or mor

How to disengage the automatic locking modeWARNING: Ford Motor Company recommends that allpassenger safety belt assemblies and attaching hardware shou

limitations regarding 911 Assist and Traffic, directions andInformation privacy below). However, parties, such as lawenforcement, could combine the ED

WARNING: The driver and front passenger safety belt system(including retractors, buckles and height adjusters) must bereplaced if the vehicle is invol

Belt-Minder姞The Belt-Minder威 feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders byinterm

If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the onposition or less than1-2 minutes h

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra

Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate

The driver and front passenger Belt-Minder威 features can bedeactivated/activated by performing the following procedure:Before following the procedure,

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The passenger airbag cover is a seamless design so that you cannot seethe boundary around its door. The shad

WARNING: All occupants of the vehicle, including the driver,should always properly wear their safety belts, even when an airbag supplemental restraint

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

CELL PHONE USEThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri

• a readiness light and tone• and the electrical wiring which connects the components• Side curtain airbag system. Refer to Side curtain airbag system

• the system determines that a small child is present in a forward-facingchild restraint that is installed according to the manufacturer’sinstructions

If a person of adult size is sitting in the front passenger’s seat, but the⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator lamp is lit, it ispos

The front passenger sensing system may detect small or medium objectsplaced on the seat cushion. For most objects that are in the frontpassenger seat,

WARNING: To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a chi

WARNING: Any alteration/modification to the front passengerseat may affect the performance of the front passenger sensingsystem.Determining if the sys

WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. Contact your authorize

not of the type sufficient to cause activation. Side airbags are designedto inflate in side-impact collisions, not roll-over, rear-impact, frontal orn

Side-curtain airbag systemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a depl

How does the side air-curtain system work?The design and development of theside air curtain system includedrecommended testing proceduresthat were dev

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

passenger seat or an unbuckled child or small person in the passengerseat. The air curtain was designed to inflate between the side windowarea and occ

Any difficulty with the system is indicated by one or more of thefollowing:• The readiness light (same light as used for front airbag system) willeith

WARNING: All children are shaped differently. TheRecommendations for Safety Restraints are based on probablechild height, age and weight thresholds fr

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeLargerchildrenChildren who have outgrown

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

WARNING: Always carefully follow the instructions andwarnings provided by the manufacturer of any child restraint todetermine if the restraint device

training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertifi

Airbags can kill or injure a child in a child seat. NEVER place arear-facing child seat in front of an active airbag. If you must use aforward-facing

To reinstall the head restraint, linethe posts up in the holes on the seatback with the head restraint strapfacing the outside of the vehicle andpush

• Keep the buckle release button pointing up and away from the safetyseat, with the tongue between the child seat and the release button,to help preve

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out.6. All

10. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the

Your vehicle has LATCH loweranchors for child seat installation atthe seating positions marked withthe child seat symbol.The LATCH anchors are located

Use of inboard lower anchors from the outboard seating positions(center seating use)The lower anchors at the center of the second row rear seat are sp

The rear seats of your vehicle are equipped with built-in tether strapanchors located behind the seats as described below.The tether anchors in your v

4. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theeven

When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the

• High back booster seatsIf, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo

If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat may improve thisconditio

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A wa

WARNING: Failure to inspect and if necessary replace thesafety belt assembly or child restraint system under the aboveconditions could result in sever

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli

WARNING: The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydro

Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr

WARNING: Under-inflation is the most common cause of tirefailures and may result in severe tire cracking, tread separationor “blowout”, with unexpecte

Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w

• Do not run over curbs or hit the tire against a curb when parkingWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the

emission control system during normal driving. If the vehicle needsI/M testing, refer to the Readiness for Inspection/Maintenance (I/M)testing section

• Front-wheel drive(FWD)/All-wheel drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can be corrected by rotating the ti

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including inter

To restore the full functionality of the tire pressure monitoring system,have the damaged road wheel/tire repaired and remounted on yourvehicle. For a

Low tire pressurewarning lightPossible cause Customer action requiredSolid warning light Tire(s)under-inflated1. Check your tire pressure toensure tir

Locks and Security 102Keys 102Locks 103Anti-theft system 115Seating and Safety Restraints 121Seating 121Safety restraints 132Airbags 146Child restrain

WARNING: Driving a vehicle with the brake system warninglight on is dangerous. A significant decrease in brakingperformance may occur. It will take yo

Low tire pressurewarning lightPossible cause Customer action requiredFlashing warninglightSpare tire in use Your temporary spare tire is inuse. Repair

under-inflated, carefully drive the vehicle to the nearest location whereair can be added to the tires. Inflate all the tires to the recommendedinflat

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment.GAW (Gross Axle Weight) – is the

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

WARNING: Do not use replacement tires with lower loadcarrying capacities than the original tires because they maylower the vehicle’s GVWR and GAWR lim

you have been planning for the past 2 years. Measuring the inside ofthe vehicle with the rear seat folded down, you have room for12-100 lb. (45 kg) ba

• Your vehicle may be towed up to a speed of 75 mph (120 km/h), butyou should always obey local speed limits.You also have the option of trailering th

STARTINGPositions of the ignition1. Off— locks the gearshift leverand allows key removal.2. Accessory— allows the electricalaccessories such as the ra

Safety belt: The warning lightilluminates momentarily when theignition is turned to the on position.Illuminates to remind you to fastenyour safety bel

order to warm the engine. If the engine idle speed does not slow downautomatically, have the vehicle checked.Before starting the vehicle:1. Make sure

Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrument Cluster chapter for more informationregarding the warning

Guarding against exhaust fumesCarbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects.WARNING: If you smell exhaus

• Do not use multiple extension cords. Instead, use one extension cordwhich is long enough to reach from the engine block heater cord tothe outlet wit

BRAKESOccasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-o

distance. The ABS will be activated immediately, allowing you to retainfull steering control during hard braking and on slippery surfaces.However, the

The BRAKE warning lamp willilluminate and will remainilluminated until the parking brakeis released.To release, press and hold the button (2), pull th

WARNING: Remember that even advanced technology cannotdefy the laws of physics. It’s always possible to lose control of avehicle due to inappropriate

• The stability control light will flash.• If your foot is on the brake pedal, a vibration in the pedal• If the driving condition is severe and your f

Certain adverse driving maneuvers may activate ESC, which include butare not limited to:• Taking a turn too fast• Maneuvering quickly to avoid an acci

malfunction with the charging system. Contact your authorized dealer assoon as possible. This indicates a problem with the electrical system or arelat

AdvanceTrac威 FeaturesControlswitchfunctionsStabilitycontrollightStabilitycontrol offlightESCTractioncontrolDefault atstart-upIlluminatedduring bulbche

WARNING: The EPS system has diagnostics checks thatcontinuously monitor the EPS system to ensure proper operationof the electronic system. When an ele

If you cannot move the gearshift lever out of P (Park) with ignition inthe on position and the brake pedal pressed, it is possible that a fuse hasblow

WARNING: Always set the parking brake fully and make surethe gearshift is latched in P (Park). Turn the ignition to the offposition and remove the key

N (Neutral)With the gearshift lever in N (Neutral), the vehicle is free to roll; holdthe brake pedal down while in this position. Because of the uniqu

WARNING: To help avoid personal injury, please read andunderstand the limitations of the reverse sensing system ascontained in this section. Reverse s

The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to th

REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rearview camera system,located on the trunk, provides avideo image which appears in therearview mirror or on t

The camera lens for the camera is located on the trunk. Keep the lensclean so that the video image remains clear and undistorted. Clean thelens with a

BLIND SPOT INFORMATION SYSTEM (BLIS姞) WITH CROSSTRAFFIC ALERT (CTA) (IF EQUIPPED)The BLIS威 is a convenience featurethat aids the driver in assessingwh

AdvanceTrac威off: Illuminates whenAdvanceTrac威 has been disabled bythe driver. Refer to the Drivingchapter for more information.Low tire pressure warni

The BLIS威 will trigger the alert for vehicles that enter your blind zonefrom the rear or merge in to the blind zone from the side. Vehicles thatyou pa

Cross traffic alert (CTA) system operationThe CTA system warns the driver of approaching vehicles when R(Reverse) is selected and the vehicle is backi

CTA coverage also decreases when parking at shallow angles (refer tofigure for approximate zone coverage areas [sensor obstructed tovehicle on left]).

CTA and Reverse Sensing System (RSS) interactionCTA works along with the Reverse Sensing System (RSS) (if equipped).Become familiar with the warning t

WARNING: Just prior to the system recognizing a blockedcondition and alerting the driver, the number of missed objectswill increase. To help avoid inj

DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co

FUEL PUMP SHUT-OFFIn the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fue

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

Throttle Control/Powertrainmalfunction (RTT): Illuminateswhen a powertrain fault has beendetected. If the indicator stays on orcontinues to come on, c

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Driver smart window motor2 15A Brake on/off switch, Centerhigh-

Fuse/RelayLocationFuse AmpRatingProtected Circuits11 10A Not used (spare)12 7.5A Power outside mirrors13 5A SYNC威 module14 10A Electronic finish panel

Fuse/RelayLocationFuse AmpRatingProtected Circuits36 5A Passive Anti-Theft Sensor (PATS)transceiver37 10A Humidity sensor38 20A Subwoofer amplifier39

The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected Circuits1 50A* Electronic power assist steeringB+2 50A* Electron

Fuse/RelayLocationFuse AmpRatingProtected Circuits13 15A** Motor electronics coolant/heaterpump (relay 42 & 44 power)14 — Not used15 — Not used16

Fuse/RelayLocationFuse AmpRatingProtected Circuits41 G8VA relay Backup lamps42 G8VA relay Heater pump43 G8VA relay Fuel pump44 G8VA relay Motor electr

The components are coded as follows:Relay Location Relay Type Function1 — Not used2 — Not used3 High currentmicroBlower motor4 High currentmicroRear w

Dissimilar spare tire/wheel informationWARNING: Failure to follow these guidelines could result in anincreased risk of loss of vehicle control, injury

3. Full-size dissimilar spare without label on wheelWhen driving with the full-size dissimilar spare tire/wheel, do not:• Exceed 70 mph (113 km/h)• Us

Removing the spare tire and jack1. Remove the carpeted load floorpanel located in the rear of thevehicle and remove the lug wrenchand long bolt from t

GAUGESYour vehicle is equipped with an LCD (liquid crystal display),reconfigurable instrument cluster. You can choose from four informationlevels, and

1. Block both the front and rear ofthe wheel diagonally opposite theflat tire. For example, if the leftfront tire is flat, block the right rearwheel.2

WARNING: To lessen the risk of personal injury, do not put anypart of your body under the vehicle while changing a tire. Do notstart the engine when y

WHEEL LUG NUT TORQUE SPECIFICATIONSRetighten the lug nuts to the specified torque at 500 miles (800 km)after any wheel disturbance (tire rotation, cha

the Easy Fuel™ “no cap” fuel system as it can be damaged. You mustuse the included funnel in such circumstances.WARNING: Do not insert the nozzle of p

3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake onboth vehicles

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex

2. Start the engine of the disabled vehicle.3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disc

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

Emergency towingIn case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport veh

Enlighten instrument cluster (standard cluster shown, metricsimilar)Displays unique hybrid vehicle gauges, along with many of the familiargauges from

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

• Service specials and promotions.In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

If your vehicle must be serviced while you are traveling or living inCentral America, the Caribbean, or the Middle East, contact the nearestauthorized

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

WAXING• Wash the vehicle first.• Do not use waxes that contain abrasives; use Motorcraft威 PremiumLiquid Wax (ZC-53-A), which is available from your au

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

Empower instrument cluster (standard cluster shown, metricsimilar)The most information-rich display, with gauges designed to allow driversto decide fo

PLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authorized dealer.• For r

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENSClean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth,

• If grease or tar is present on the material, spot-clean the area firstwith Motorcraft威 Spot and Stain Remover (ZC-14). In Canada, useMotorcraft威 Mul

FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

WARNING: To reduce the risk of vehicle damage and/orpersonal burn injuries, do not start your engine with the aircleaner removed and do not remove it

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT1. Engine coolant reservoir2. Engine oil filler cap3. Engine oil dipstick4. Motor/Electronics (M/E) co

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice

• Do not overfill the engine with oil. Oil levels above the upperhole/line may cause engine damage. If the engine is overfilled,some oil must be remov

Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature, the level indicator willbe blue and will be in t

To protect your engine and engine’s warranty, use Motorcraft威 SAE5W-20 or an equivalent SAE 5W-20 oil meeting Ford specificationWSS-M2C930-A. SAE 5W-2

Note: Electrical or electronic accessories or components added tothe vehicle by the dealer or the owner (e.g. spot lights, electricwinch, etc.) may ad

5. Step on the accelerator to start the engine. While the engine isrunning, shift the vehicle to neutral.6. Allow the vehicle to run for at least one

Checking engine coolantThe concentration and level ofengine coolant should be checked atthe intervals listed in scheduledmaintenance information. Thec

• Protection against rust and other forms of corrosion.• Enables calibrated gauges to work properly.Common instructions for cooling systems• The engin

improper coolant may harm engine and cooling system componentsand may void the warranty. Refer to Maintenance productspecifications and capacities in

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap.5. Fill the coolant reservoi

• NEVER increase the coolant concentration above 60%.• A coolant concentration of 60% will provide freeze pointprotection down to -62°F [-52°C]. Incre

WARNING: The fuel system may be under pressure. If you heara hissing sound near the fuel filler door (Easy Fuel™ “no cap”fuel system), do not refuel u

splashed on the skin, promptly wash skin thoroughly with soap andwater. Consult a physician immediately if you experience an adversereaction.WARNING:

Enlighten, Engage and Empower instrument cluster levels only: Theup and down arrows provide information about the energy (both storedand used) associa

Easy Fuel™ “no cap” fuel systemYour fuel tank is equipped with an Easy Fuel™ “no cap” fuel fillersystem. This allows you to simply open the fuel fille

WARNING: The fuel system may be under pressure. If you heara hissing sound near the fuel filler door (Easy Fuel™ “no cap”fuel system), do not refuel u

Fuel qualityIf you are experiencing starting, rough idle or hesitation driveabilityproblems during a cold start, try a different brand of “Regular” un

Refilling with a portable fuel containerWith the Easy Fuel™ “no cap” fuel system, use the following directionswhen filling from a portable fuel contai

ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform

5. Follow one of the simple calculations in order to determine fueleconomy:Calculation 1: Divide total miles traveled by total gallons used.Calculatio

• Combine errands. Your vehicle is more fuel efficient when the engineis warm. Driving to your farthest destination first will warm the enginemore qui

EMISSION CONTROL SYSTEMYour vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to co

it from working. Information about your vehicle’s emission system is onthe Vehicle Emission Control Information Decal located on or near theengine. Th

Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect

Customer Assistance 260Reporting safety defects (U.S. only) 266Reporting safety defects (Canada only) 266Cleaning 267Maintenance and Specifications 27

Instantaneous fuel economygauge: The instantaneous fueleconomy is displayed in miles pergallon (or liters per 100 kilometers)from 0 to 60 mpg (or 0 to

BRAKE FLUIDThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Check fluid levels with the ignitio

MOTORCRAFT PART NUMBERSComponent 2.5L iVCT engineOil filter FL-910Spark plugs1Cabin air filter FP-67Low voltage (underhood)batteryBXT-67-R1For spark p

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord Part Name orequivalentFord Part Number / FordSpecificationBrake fluidBetween MINand

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationWindshield washerfluidFill as requiredMotorcraft威 PremiumWindshield Washer

ENGINE DATAEngine 2.5L I4 engineCubic inches 152Required fuel 87 octaneFiring order 1-3-4-2Ignition system Coil on plugSpark plug gap 0.049–0.053 inch

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

Peace of mindRemote startVehicle security systemsWheel locksFor maximum vehicle performance, keep the following information inmind when adding accesso

GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?This guide describes the scheduled maintenance required for yourvehicle. Carefully following

History graph: Indicates averagefuel economy in 10, 20, or60 minute intervals. You can choosethe interval using the messagecenter. The graph is update

parts that are used for maintenance replacement or for the service ofcomponents affecting emission control must be equivalent to genuineFord Motor Com

Company’s specifications, and we stand behind them. Maintenance partsinstalled at your Ford or Lincoln Mercury dealership carry a nationwide,12 months

Multi-point InspectionIn order to keep your vehicle running right, it is important that you havethe systems on your vehicle checked regularly. This ca

website. You’ll also find important warranty information, customerassistance, technical expertise, frequently asked questions and muchmore. The websit

30,000 miles (48,000 km)❑Change engine oil and replace oil filter❑Inspect tires for wear and measure tread depth❑Rotate tires❑Inspect wheel ends for e

60,000 miles (96,000 km)❑Change engine oil and replace oil filter❑Inspect tires for wear and measure tread depth❑Rotate tires❑Inspect wheel ends for e

90,000 miles (144,000 km)❑Change engine oil and replace oil filter❑Inspect tires for wear and measure tread depth❑Rotate tires❑Inspect wheel ends for

120,000 miles (192,000 km)❑Change engine oil and replace oil filter❑Inspect tires for wear and measure tread depth❑Rotate tires❑Inspect wheel ends for

SPECIAL OPERATING CONDITIONSExtensive Idling and/or Low Speed Driving for Long Distances as in HeavyCommercial Use Such as Delivery, Taxi, Patrol Vehi

Current mileage goes here =>Add 50,000 miles to the current miles + 50,000Next change due at this mileage =>OrToday’s date goes here =>Add 3

To determine your average highway fuel economy, do the following:1. Drive the vehicle at least 5 miles (8 km) with the speed controlsystem engaged to

Current mileage goes here =>Add 50,000 miles to the current miles + 50,000Next change due at this mileage =>OrToday’s date goes here =>Add 3

FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan3232010 Fusion Hybrid (hfv)Owners Guide, 3rd PrintingUSA (fus)

AAccessory delay ...95AdvanceTrac ...216Air cleaner filter ...300–301Air conditioningaut

Child safety seats ...166attaching with tether straps ..174in front seat ...167in rear seat ...

checking and adding ...278dipstick ...278filter, specifications ...279, 301recommendations ...

KKeyless entry systemautolock ...103keypad ...114locking and unlocking doors ..115pr

Recommendations forattaching safety restraints forchildren ...164Relays ...238, 245Rem

TTilt steering wheel ...87Tire Pressure MonitoringSystem (TPMS)Tires, Wheels and Loading ...196Tires ...18

EV mode only (enlighteninstrument cluster level only):When the hybrid system is operatingin electric vehicle mode only, EV isdisplayed.Split power gau

Vehicle power gauge (empowerinstrument cluster only): Whenthe transmission is in a drive gearonly, this gauge shows you vehiclepower demand and gasoli

Trip summary: When the ignition key is turned to the off position, theinstrument cluster will transition to a trip summary screen whichdisplays the fo

Info menuThe top line of the display is theodometer which is always present.Repeatedly pressing the INFObutton cycles the display throughthe following

Average fuel economyPress INFO to display your averagefuel economy in miles/gallon orliters/100 km.If you calculate your average fueleconomy by dividi

The setup menu operates by use ofthe INFO, SETUP, and RESETbuttons:• SETUP: Press to enter the setupmenu. Press SETUP to scrollthrough the list in the

Display ModeChoosing display mode allows you toselect which instrument cluster levelyou would like displayed. WhileDisplay Mode is highlighted, pressR

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

FE History LengthUse this to set the fuel efficiencyhistory length for the history graph.While FE History Length ishighlighted, press RESET to selecti

Vehicle SettingsPress SETUP to reach VehicleSettings.While Vehicle Settings is highlighted,press RESET to select it and moveright to display the follo

AutolockThis feature automatically locks allvehicle doors when the vehicle isshifted into any gear, putting thevehicle in motion.While Autolock is hig

Blind Spot (if equipped)The blind spot information system isdesigned to assist the driver bymonitoring the side areas on bothsides of the vehicle and

Rear Park Aid (if equipped)This feature sounds a warning toneto warn the driver of obstacles nearthe rear bumper, and functions onlywhen R (Reverse) g

• Set to 100% • Set to 90%• Set to 20% • Set to 10%Press SETUP to scroll through the list and highlight one of the choices.Press RESET to pick the hig

TutorialThe tutorial is a self-paced guidethat provides a brief overview ofinstrument cluster features.Press SETUP to reach Tutorial.While Tutorial is

Warning messages that have been reset are divided into two categories:• They will reappear on the display 10 minutes from the reset.• They will not re

POWER STEERING ASSIST FAULT — The power steering systemhas disabled power steering assist due to a system error, service isrequired.SERVICE POWER STEE

TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressuresensor is malfunctioning, or your spare tire is in use. For moreinformation on how the syst

Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti

TO STOP ALARM START VEHICLE — Displayed when the perimeteralarm system is armed and the vehicle is entered using the key on thedriver’s side door. In

AUDIO SYSTEMSAM/FM/single CD or in-dash CD6/MP3 satellite-compatible soundsystemWARNING: Driving while distracted can result in loss of vehiclecontrol

AM/FM Radio/ VOL (Power/Volume): Press to turn the radio on/off. Turn theknob to increase/decrease volume.If the volume is set above a certain level a

RDS (Radio Data System) RadioAvailable only in FM mode. This feature allows you to searchRDS-equipped stations for a certain category of music format:

For a CD6 system– press EJECT and select the desired CD slot bypressing the corresponding memory preset #. The display will readEJECTING #. When the s

SHUFFLE: Press MENU repeatedly until SHUFFLE ON/OFF appears inthe display. UseSEEK/TRACK to switch between ON/OFF. Ifyou wish to engage shuffle mode r

MEMORY PRESETS (0–9): Thereare 30 available presets, 10 each forSAT1, SAT2 and SAT3. To savesatellite channels in your memorypresets, tune to the desi

the system will take you to the channel playing the desired song. Youcan save up to 20 song titles. If you attempt to save more than 20titles, the dis

when the system accepts your entry it will display ENTER NEW PIN.Enter your new four-digit PIN and the system will save the new PINand PIN SAVED will

Extra FeaturesAUX: Press repeatedly to cycle through LINE IN (auxiliary audio mode),and SYNC威.For location and further information on auxiliary audio

HYBRID OPERATIONThis hybrid vehicle combines electric and gasoline propulsion withoutcompromise, to provide breakthrough performance and efficiency. I

Required equipment:1. Any portable music player designed to be used with headphones2. An audio extension cable with stereo male 1/8 in. (3.5 mm)connec

5. For safety reasons, connecting or adjusting the settings on yourportable music player should not be attempted while the vehicle ismoving. Also, the

• Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thunderstorms can interfere with your reception.• Station

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio forthe selectedchannel.No action required. Thisme

Radio Display Condition Action RequiredNO TEXT Categoryinformation notavailable.Category information notavailable at this time onthis channel. The sys

DUAL AUTOMATIC TEMPERATURE CONTROL (IF EQUIPPED)1. AUTO/Driver temperature: Press to engage full automaticoperation. Select the desired temperature us

5. Power/ : Press to activate/deactivate the climate controlsystem. When the system is off, outside air is prevented from enteringthe vehicle through

Transmission Operation: Due to the technologically advanced,electronically-controlled Continuously Variable Transaxle (eCVT) you willnot feel shift ch

11. Recirculated air: Press to activate/deactivate air recirculationin the vehicle. Recirculated air may reduce the amount of time needed tocool down

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL (NAVIGATIONBASED – IF EQUIPPED)1. CLIMATE: Press to control the climate control system through thetouch displa

6. Recirculated air: Press to activate/deactivate air recirculation inthe vehicle. Recirculated air may reduce the amount of time needed tocool down t

TOUCHSCREEN FUNCTIONSTemperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the Instrument Cluster chapter.Temper

signify that the feature has been disabled. The system will return to theprevious mode after Dual is release.To re-enable the smart-zone feature: Pres

3. Set the temperature to 60°F (16°C).• Manual operation:1. Select MAX A/C.2. Selector .3. Select(recirculated air) to provide colder airflow.4. Set t

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the low beam headlampso

4. Turn the headlamp control to the autolamp position. The headlampswill turn on.5. Wait the desired amount of time for the exit delay you want (up to

High beamsPush the lever toward theinstrument panel to activate. Pullthe lever toward you to deactivate.Flash-to-passPull toward you slightly to activ

Note: If the battery is disconnected, discharged, or a new battery isinstalled, the dimmer control requires re-calibration. Press the dimmercontrol fr

(Low voltage [underhood] battery only) in the Roadside Emergencieschapter and also refer to Low and high voltage battery — storage inthe Maintenance a

5. Locate the vertical adjuster oneach headlamp. Using a Phillips #2screwdriver, turn the adjuster eitherclockwise (to adjust down) orcounterclockwise

Your vehicle may also have readinglamps within the rear dome lamp(s).Press the switches on either side ofthe dome lamp to turn on thelamps.Ambient lig

• Large water droplets, drip marks or streaks present on the interior ofthe lensTake your vehicle to a dealer for service if any of the above conditio

Replacing interior bulbsCheck the operation of all bulbs frequently.Replacing exterior bulbsCheck the operation of all the bulbs frequently.Replacing

effective point to grasp the trunk side panel when pulling it out from theluggage scuff plate is at it’s bottom edge where that edge meets theexposed

Replacing fog lamp bulbs1. Make sure the fog lamp switch isin the off position.2. From underneath the vehicle,partially remove the tire splashshield b

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

TILT/TELESCOPE STEERING WHEELTo adjust the steering wheel:1. Pull the lever down to unlock thesteering column.2. While the lever is in the downpositio

OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehicle’s overhead console will vary according toyour option package.Storage compartmentPress on

Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the on p

NOTE: Having your engine running is not always an indication ofinefficiency – in some cases it is actually more efficient than driving inelectric mode

2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons.3. Slowly d

INSTRUMENT PANEL STORAGE COMPARTMENTThe storage compartment may beused to secure sunglasses or similarsized objects. Press the button toopen the stora

Power point (110V AC)The 110V AC power point outlet,located on the rear of the floorconsole, is used for poweringelectrical devices that require up to

located in the top left corner is turned on. Refer to the indicator lightcode below for the power point status.Note: Using the 110V AC power point for

To operate one-touch down:• Press the switch completely downto the second detent and releasequickly. The window will openfully. Momentarily press thes

Window lockThe window lock feature allows onlythe driver and front passenger tooperate the power windows.To lock out all the window controls(except fo

Note: If equipped with a rearview camera system, a video image will bedisplayed in the mirror or the navigation system display (if equipped)when the v

Using speed controlThe speed controls are located on the steering wheel. The followingbuttons work with speed control:– SET +: Press to increase ordec

Increasing speed while using speed controlTo increase the set speed:• Press and hold SET + until you get to the desired speed, then release.You can al

SYNC威 system hands freecontrol featuresPressbriefly to use the voicecommand feature. You will hear atone and LISTENING will appear inthe radio display