Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Message center 19Entertainment Systems 29AM/FM stereo with CD/MP3 29Auxiliary
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
• Ensure that the trunk is closed and latched before driving yourvehicle. Failure to properly latch the trunk may cause objects to fallout or block th
system section of this chapter. Note: At least two IKTs are required toperform this procedure yourself.Illuminated entryThe interior lamps and puddle
1. Place the key in the ignition andturn the ignition to the 3 (on)position.2. Press the power door unlockcontrol on the door panel threetimes.3. Turn
SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• open the trunk.Th
The anti-scan feature will turn off after:• one minute of keypad inactivity.• pressing thecontrol on the remote entry transmitter portion ofyour Integ
Note: Large metallic objects, electronic devices that are used topurchase gasoline or similar items, or a second coded key on the samekey chain may ca
The theft indicator will illuminate for three seconds and then go out. Ifthe theft indicator stays on for an extended period of time or flashesrapidly
Please read and understand theentire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition.2. Turn the igniti
PERIMETER ALARM SYSTEMThe perimeter anti-theft system will help protect your vehicle fromunauthorized entry.If there is any potential perimeter anti-t
Disarming the systemYou can disarm the system by any of the following actions:• Unlock the doors by using the remote entry transmitter portion ofyour
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o
To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o
To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous
WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Using the manual lumbar support (if eq
Pump the handle upwards to raisethe cushion and pump downward tolower the cushion to the desiredlocation.Pull lever up to adjust seatback.Folding down
WARNING: Before returning the seatback to its originalposition, make sure that cargo or any objects are not trappedbehind the seatback. After returnin
The control is located on the outboard side of the seat cushion.Move the control in the direction ofthe arrows to raise or lower thefront portion of t
Heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cordinjur
WARNING: To minimize the risk of neck injury in the event of acrash, the driver and passenger occupants should not sit inand/or operate the vehicle, u
2. Lower the head restraint bypressing and holding the guidesleeve adjust/release button andpushing down on the head restraint.Properly adjust the hea
WARNING LIGHTS AND CHIMESStandard instrument cluster shown, optional cluster and vehicleswith manual transmission similarWarning lights and gauges can
2. Insert and push a tool, such as alarge paper clip, into the pin holelocated on the side of the guidesleeve and press the adjust/releasebutton, then
To reinstall the adjustable head restraint, do the following:1. Insert the two stems into theguide sleeve collars.2. Push the head restraint downuntil
To lower the seatback(s), pull therelease handle(s) located inside thetrunk.Fold the seatback(s) down.WARNING: Before returning the seatback to its or
Seat-mounted cup holders and armrest storage compartmentTo access the cup holders, fold thearmrest down.WARNING: Use only soft cups in the cup holder.
How does the Personal Safety System姞 work?The Personal Safety System威 can adapt the deployment strategy of yourvehicle’s safety devices according to c
to the airbag when it begins to inflate. For some occupants, this occursbecause they are initially sitting very close to the airbag. For otheroccupant
Front safety belt energy management retractorsThe front outboard safety belt energy management retractors allowwebbing to be pulled out of the retract
WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of l
Solid illumination after the engine is started indicates the On BoardDiagnostics System (OBD-II) has detected a malfunction. Refer to Onboard diagnost
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
WARNING: Position the safety belt height adjusters so that thebelt rests across the middle of your shoulder. Failure to adjustthe safety belt properly
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war
The Belt-Minder威 feature uses two different warning chimes. During thefirst minute of activation, the warning chime will sound once everysecond. The r
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate
• The gearshift is in N (Neutral) (manual transmission)• The gearshift is in P (Park) (automatic transmission)• The ignition switch is in the off posi
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The passenger airbag cover is a seamless design so that you cannot seethe boundary around its door. The shad
WARNING: All occupants of the vehicle, including the driver,should always properly wear their safety belts, even when an airbag supplemental restraint
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
Airbag readiness: If this light failsto illuminate when the ignition isturned to on, continues to flash orremains on, contact your authorizeddealer as
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
• a readiness light and tone• and the electrical wiring which connects the components• Side curtain airbag system. Refer to Side curtain airbag system
The front passenger sensing system will turn off the passenger seat sideairbag if:• the seat is empty and safety belt is unbuckled.• a child or a smal
If a person of adult size is sitting in the front passenger’s seat, but the⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator lamp is lit, it ispos
The front passenger sensing system may detect small or medium objectsplaced on the seat cushion. For most objects that are in the frontpassenger seat,
WARNING: To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a chi
WARNING: Any alteration/modification to the front passengerseat may affect the performance of the front passenger sensingsystem.Determining if the sys
WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. Contact your authorize
The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of
Side curtain airbag systemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a depl
Overdrive cancel and gradeassist: Illuminates when theoverdrive function of thetransmission has been turned offand the grade assist function hasbeen t
How does the side air curtain system work?The design and development of theside air curtain system includedrecommended testing proceduresthat were dev
passenger seat or an unbuckled child or small person in the passengerseat. The air curtain was designed to inflate between the side windowarea and occ
Any difficulty with the system is indicated by one or more of thefollowing:• The readiness light (same light as used for front airbag system) willeith
WARNING: All children are shaped differently. TheRecommendations for Safety Restraints are based on probablechild height, age and weight thresholds fr
• You are required by law to properly use safety seats for infants andtoddlers in the U.S. and Canada.• Many states and provinces require that small c
WARNING: Air bags can kill or injure a child in a child seat.NEVER place a rear-facing child seat in front of an active airbag. If you must use a forw
WARNING: Do not leave children, unreliable adults, or petsunattended in your vehicle.Transporting childrenAlways make sure your child is secured prope
SAFETY SEATS FOR CHILDRENInfant and/or toddler seatsUse a safety seat that is recommended for the size and weight of thechild.When installing a child
To remove the head restraint, insertand push a tool, such as a largepaper clip, into the pin hole locatedon the side of the guide sleeve andpress the
Refer to Rear adjustable head restraints earlier in this chapter formore information.WARNING: If the head restraint has been removed from aseating pos
Turn signal: Illuminates when theleft or right turn signal or thehazard lights are turned on. If theindicators flash faster, check for a burned out bu
1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
Sometimes, a slight lean towards the buckle will additionally help toremove remaining slack from the belt.9. Attach the tether strap (if the child sea
Your vehicle has LATCH loweranchors for child seat installation atthe seating positions marked withthe child seat symbol.The LATCH anchors are located
Use of inboard lower anchors from the outboard seating positions(center seating use)The lower anchors at the center of the second row rear seat are sp
Attaching child safety seats with tether strapsMany forward-facing child safety seats include a tether strap whichextends from the back of the child s
3. Open the tether anchor cover.4. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safety seat maynot
Although the lap/shoulder belt will provide some protection, childrenwho have outgrown a typical child seat are still too small for lap/shoulderbelts
Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
Move a child to a different seating location if the shoulder belt does notstay positioned on the shoulder during use.Follow all instructions provided
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli
WARNING: The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydro
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
WARNING: Under-inflation is the most common cause of tirefailures and may result in severe tire cracking, tread separationor ⬙blowout⬙, with unexpecte
Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo
Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w
• Do not run over curbs or hit the tire against a curb when parkingWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the on position). The fuelgauge may vary slightly whe
• Front Wheel Drive (FWD)/AllWheel Drive (AWD) vehicles(front tires at top of diagram)Sometimes irregular tire wear can be corrected by rotating the t
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw
Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti
When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.
MESSAGE CENTERWith the ignition in the on position,the message center, located on yourinstrument cluster, displaysimportant vehicle informationthrough
Low Tire PressureWarning LightPossible cause Customer Action RequiredFlashing WarningLightSpare tire in use Your temporary spare tire is inuse. Repair
SNOW TIRES AND CHAINSWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel
VEHICLE LOADINGThis section will guide you in the proper loading of your vehicle to keepyour loaded vehicle weight within its design rating capability
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment.GAW (Gross Axle Weight) – is the
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
WARNING: Do not use replacement tires with lower loadcarrying capacities than the original tires because they maylower the vehicle’s GVWR and GAWR lim
• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the l
Front Wheel Drive (FWD) 2.5L and 3.0L vehicles:Tow your Front Wheel Drive vehicle with all four wheels on the groundor with the front wheels off the g
Front Wheel Drive (FWD) 3.5L vehicles:Do not tow the vehicle with the front drive wheels on the ground ortransmission damage may occur. It is recommen
STARTINGPositions of the ignition1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accesso
Locks and Security 90Keys 90Locks 92Anti-theft system 104Seating and Safety Restraints 110Seating 110Safety restraints 123Airbags 137Child restraints
Distance to empty (DTE)Selecting this function from theINFO menu estimates approximatelyhow far you can drive with the fuelremaining in your tank unde
WARNING: Do not start your vehicle in a closed garage or inother enclosed areas. Exhaust fumes can be toxic. Always openthe garage door before you sta
• Make sure the gearshift is in P(Park).If starting a vehicle with a manualtransmission:• Make sure the parking brake isset.• Push the clutch pedal to
Starting the engine1. Turn the key to 3 (on) withoutturning the key to 4 (start).2. Turn the key to 4 (start), thenrelease the key as soon as theengin
the user to connect the system to a grounded 120 volt a/c electricalsource. The block heater system is most effective when outdoortemperatures reach b
become very hot and may result in an electrical shock or fire. Be sureto check for heat anywhere in the electrical hookup once the systemhas been oper
ABS warning lampThe ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringsta
WARNING: Always set the parking brake fully and make surethat the gearshift is securely latched in P (Park) (automatictransmission) or in 1 (First) (m
Your vehicle is equipped with the AdvanceTrac威 system. TheAdvanceTrac威 system provides the following stability enhancementfeatures for certain driving
Traction Control (TCS)Traction Control is a driver aid feature that helps your vehicle maintaintraction of the wheels, typically when driving on slipp
•Entering a snow-free road from a snow-covered side street, or vice versa• Entering a paved road from a gravel road, or vice versa• Cornering while to
For more information refer to Essentials of good fuel economy in theMaintenance and Specifications chapter.Instantaneous fuel economy (IFE)Select this
STEERING2.5L I4 engine and 3.0L V6 Duratec engines: Your vehicle isequipped with an Electric Power Steering (EPS) system. There is nofluid reservoir t
To help prevent damage to the power steering system, never hold thesteering wheel at its furthest turning points (until it stops) for more thana few s
If you cannot move the gearshift lever out of P (Park) with ignition inthe on position and the brake pedal depressed:1. Apply the parking brake, turni
AUTOMATIC TRANSMISSION OPERATIONUnderstanding the gearshift positions of the 6–speed automatictransmission equipped with a 2.5L I4 engine (if equipped
N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D
To put your vehicle in gear:• Depress the brake pedal• Move the gearshift lever into the desired gearTo put your vehicle in P (Park):• Come to a compl
D (Drive) with Overdrive Cancel and Grade AssistInitially, moving the lever to (M)activates two features at the sametime: Overdrive cancel and gradeas
To return to O/D (overdrive mode), move the shift lever back from ⬙M⬙to ⬙D.⬙• The overdrive cancel and grade assist lamp in the instrument clusterwill
To manually downshift the transmission:1. Move the gearshift lever forwardto (-).2. Release the lever, and it willreturn to the M position. Thetransmi
MANUAL TRANSMISSION OPERATION (IF EQUIPPED)Using the clutchManual transmission vehicles have a starter interlock that preventscranking the engine unle
System checkSelecting this function from theSETUP menu causes the messagecenter to cycle through each of thesystems being monitored.Pressing the RESET
Upshift according to the following chart:Upshifts when accelerating (recommended for best fueleconomy)Shift from:1 - 2 15 mph (24 km/h)2 - 3 25 mph (4
REVERSE SENSING SYSTEM (IF EQUIPPED)The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when the R (Rev
The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to th
REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rear-view camera system,located on the trunk, provides avideo image which appears in therear view mirror or on
Note: The default setting for the rear camera delay is off. Push the“Settings” button found on the navigation screen to set the rear cameradelay featu
BLIND SPOT INFORMATION SYSTEM™ (BLIS™) WITH CROSSTRAFFIC ALERT (CTA) (IF EQUIPPED)The BLIS™ system is a conveniencefeature that aids the driver inasse
The BLIS™ will trigger the alert for vehicles that enter your blind zonefrom the rear or merge in to the blind zone from the side. Vehicles thatyou pa
Cross traffic alert (CTA) system operationThe cross traffic alert system warnsthe driver of approaching vehicleswhen R (Reverse) is selected andthe ve
The Cross Traffic Alert system detects vehicles approaching up to 45 feet(14 meters) away (approximately the width of five parking spaces).Coverage de
Cross Traffic coverage also decreases when parking at shallow angles(refer to figure for approximate zone coverage areas [sensorobstructed to vehicle
3. Once “OIL LIFE SET TO XXX%” is displayed, release and press theRESET control switch to change the Oil Life Start Value. Each releaseand press will
on at the next ignition key cycle. When either the BLIS™ or CTA isturned off, the message center displays BLIND SPOT SYS OFF and/orCTA SYSTEM OFF. Whe
or the driver can cycle the ignition key. If blocked and the ignition key iscycled, the system resets to unblocked. If however blockage is stillpresen
All components of the AWD system are sealed for life and require nomaintenance.Note: When an AWD system fault is present, the warning CHECK AWDwill di
• It may be safer to stay on the apron or shoulder of the road and slowdown gradually before returning to the pavement. You may losecontrol if you do
not more. Additionally, smooth variations of the accelerator and/orbrake pedal pressure should be utilized if changes in vehicle speed arecalled for.
Be cautious of sudden changes in vehicle speed or direction when youare driving in mud. Even AWD vehicles can lose traction in slick mud. Aswhen you a
Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;
Maintenance and ModificationsThe suspension and steering systems on your vehicle have been designedand tested to provide predictable performance wheth
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co
AutounlockThis feature automatically unlocks all vehicle doors when the driver’sdoor is opened within 10 minutes of the ignition being turned off.1. T
After an accident, if the engine cranks but does not start, this switchmay have been activated.The fuel pump shut-off switch islocated in the front pa
FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth
To remove a fuse use the fuse puller tool provided on the fuse panelcover.The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected Cir
Fuse/RelayLocationFuse AmpRatingProtected Circuits10 15A Backlighting, Puddle lamps11 10A AWD module12 7.5A Power outside mirrors13 5A SYNC module14 1
Fuse/RelayLocationFuse AmpRatingProtected Circuits36 5A Passive Anti-Theft Sensor (PATS)transceiver37 10A Not used (Spare)38 20A Subwoofer amplifier39
If the battery has been disconnected and reconnected, refer to theBattery section of the Maintenance and Specifications chapter.The high-current fuses
Fuse/RelayLocationFuse AmpRatingProtected Circuits15 — Not used16 15A** Transmission module (3.5L)17 10A** Alternator18 — Not used19 — Not used20 — No
Fuse/RelayLocationFuse AmpRatingProtected Circuits44 — Not used45 15A** Injectors46 15A** PCM47 10A** General powertrain components, A/Cclutch relay,
WARNING: The use of tire sealants may damage your TirePressure Monitoring System and should not be used.WARNING: Refer to Tire pressure monitoring sys
Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following:• Handling, stability and braki
Language1. Select this function from theSETUP menu for the currentlanguage to be displayed.2. Waiting four seconds or pressingRESET cycles the message
2. Place the gearshift lever in P (Park) (automatic transmission) or R(Reverse) (manual transmission) and turn the engine off.Removing the spare tire
Note: Passengers should not remain in the vehicle when the vehicle isbeing jacked.1. Block both the front and rear ofthe wheel diagonally opposite the
WARNING: To lessen the risk of personal injury, do not put anypart of your body under the vehicle while changing a tire. Do notstart the engine when y
WHEEL LUG NUT TORQUE SPECIFICATIONSRetighten the lug nuts to the specified torque at 500 miles (800 km)after any wheel disturbance (tire rotation, cha
WARNING: Do not insert the nozzle of portable fuel containersor aftermarket funnels into the Easy Fuel™ system. This coulddamage the fuel system and i
Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
PASSENGER DOOR AJAR — Displayed when the passenger side dooris not completely closed.REAR LEFT DOOR AJAR — Displayed when the rear left door is notcom
Emergency towingIn case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport veh
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized
In Canada:Mailing Address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph
In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
If your vehicle must be serviced while you are traveling or living inCentral America, the Caribbean, or the Middle East, contact the nearestauthorized
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is
WAXING• Wash the vehicle first.• Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your aut
SERVICE ADVANCETRAC — Displayed when the AdvanceTrac威system has detected a condition that requires service.TRUNK AJAR — Displayed when the trunk is no
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
3.0L ENGINE3.5L ENGINEPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your aut
WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub
• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to a
WARNING: Do not use cleaning solvents, bleach or dye on thevehicle’s safety belts, as these actions may weaken the beltwebbing.WARNING: On vehicles eq
FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
Working with the engine on• Automatic transmission:1. Set the parking brake and shift to P (Park).2. Block the wheels.• Manual transmission:1. Set the
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.5L I4 engine1. Engine coolant reservoir2. Engine oil filler cap3. Engine oil dipstick4. Brake/Clutch
3.0L V6 Duratec engine1. Engine coolant reservoir2. Brake fluid reservoir3. Transmission fluid dipstick (automatic transmission only)4. Battery5. Powe
TO STOP ALARM START VEHICLE — Displayed when the perimeteralarm system is armed and the vehicle is entered using the key on thedriver’s side door. In
3.5L V6 Duratec engine1. Power steering fluid reservoir2. Transmission fluid dipstick3. Brake fluid reservoir4. Battery5. Power distribution box6. Air
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
Poor wiper quality can be improved by cleaning the wiper blades and thewindshield. Refer to Windows and wiper blades in the Cleaningchapter.To prolong
• 3.0L V6 Duratec engine• 3.5L V6 Duratec engine6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.2010 Fusion (fsn)Owners Gu
On the 2.5L I4 engine, be sure thenotch in the dipstick flange isaligned with the V on the enginewhen reinserting it.• 2.5L I4 engine• 3.0L/3.5L V6 Du
• 2.5L I4 engine• 3.0L V6 Duratec engine• 3.5L V6 Duratec engineIf required, add engine oil to the engine. Refer to Adding engine oil inthis chapter.2
• 2.5L I4 engine• 3.0L/3.5L V6 Duratec engines•Do not overfill the engine with oil. Oil levels above this markmay cause engine damage. If the engine i
To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level dipstick and/or the engine oil filler cap removed.Engine oil and filte
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If
WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work
AUDIO SYSTEMSAM/FM/single CD or in-dash CD6/MP3 satellite compatible soundsystemWARNING: Driving while distracted can result in loss of vehiclecontrol
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
• Add Motorcraft Premium Gold Engine Coolant or equivalentmeeting Ford specification WSS-M97B51-A1. Refer toMaintenance product specifications and cap
Add the proper mixture of coolant and water to the cooling system byfollowing these steps:1. Before you begin, turn the engine off and let it cool.2.
After any coolant has been added, check the coolant concentration.Refer to the Checking engine coolant section. If the concentration isnot 50/50 (prot
• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequatefreeze protection at the tempera
When this occurs the vehicle will still operate. However:• The engine power will be limited.• The air conditioning system will be disabled.Continued o
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsWARNING: Do not overfill the fuel tank. The pressure in anoverfilled tank may c
• Fuels can also be harmful if absorbed through the skin. If fuel issplashed on the skin and/or clothing, promptly remove contaminatedclothing and was
WARNING: When refueling always shut the engine off andnever allow sparks or open flames near the filler neck. Neversmoke while refueling. Fuel vapor i
Customer Assistance 261Reporting safety defects (U.S. only) 267Reporting safety defects (Canada only) 267Cleaning 268Maintenance and Specifications 27
AM/FM Radio/ VOL (Power/Volume): Press to turn the radio on/off. Turn theknob to increase/decrease volume.If the volume is set above a certain level a
When fueling your vehicle:1. Turn the engine off.2. Open the fuel filler door.3. Slowly insert the fuel filler nozzle fully into the fuel system. Pump
Flex Fuel Vehicle (FFV) fuel fill inletIf your vehicle is flex fuel capable, it will have a yellow bezel placed overthe fuel fill inlet.Choosing the r
FFV engine (if equipped)If your vehicle is flex fuel capable, it is designed to use Fuel Ethanol(Ed75–Ed85), “Regular” unleaded gasoline or any mixtur
Cleaner airFord endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality, per the recommendations in the Choosing the rightf
1. Locate the white plastic funnel. Itis attached to the underside of thespare tire cover or is included withthe tire changing tools.2. Slowly insert
vehicle after the fuel gauge indicates empty, you might not beable to refuel the full amount of the advertised capacity of thefuel tank due to the emp
Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin
• Adding certain accessories to your vehicle (for example; bugdeflectors, rollbars/light bars, running boards, ski/luggage racks) mayreduce fuel econo
WARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine compartment and exhaus
4. Driving through deep water—the electrical system may be wet.These temporary malfunctions can be corrected by filling the fuel tankwith good quality
CAT/FOLD (Category/Folder): This feature allows you to select fromvarious music categories.To change RDS categories: Press MENU repeatedly until RDS O
15 minutes of steady driving on an expressway/highway followed by20 minutes of stop-and-go driving with at least four 30-second idleperiods.Allow the
BRAKE/CLUTCH FLUIDBrake and clutch systems are supplied from the same reservoir.• 2.5L engine• 3.0L and 3.5L enginesThe fluid level will drop slowly a
Checking automatic transmission fluid at normal operatingtemperature (140°F-158°F [60°C-70°C])Automatic transmission fluid expands when warmed. To obt
Low fluid levelDo not drive the vehicle if the fluidlevel does not show at all on thedipstick.Driving the vehicle with less thanthe recommended fluid
Checking automatic transmission fluid (6F35) (if equipped)Refer to your scheduled maintenance information for scheduledintervals for fluid checks and
The transmission fluid should be inthe crosshatch zone if at normaloperating temperature (150°F-170°F[66°C-77°C]).High fluid levelFluid levels above t
Checking and adding manual transmission fluid (if equipped)1. Park the vehicle on a levelsurface.2. Engage the parking brake fully –put in first gear.
Changing the air filter element• 2.5L I4 engine• 3.0L V6 Duratec engine• 3.5L V6 Duratec engine1. Release the clamps that secure the air filter housin
• 2.5L I4 engine• 3.0L V6 Duratec engine• 3.5L V6 Duratec engine3. Remove the air filter element from the air filter housing.2010 Fusion (fsn)Owners G
4. Wipe the air filter housing and cover clean to remove any dirt ordebris and to ensure good sealing.5. Install a new air filter element. Be careful
/ Play/Pause: Press toplay/pause a track when playing aCD.SEEK/TRACK: PressSEEK/TRACK to access theprevious/next track.CAT (Category) / FOLD (Folder):
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number / FordspecificationBrake (and clutch–ifequipped) fluidBe
Item Capacity Ford part nameFord part number / FordspecificationEngine oil(2.5L engine)5.0 quarts(4.7 L)•Motorcraft SAE 5W-20Premium Synthetic BlendMo
Item Capacity Ford part nameFord part number / FordspecificationRear differential(AWD) fluid2.4 pints(1.15L)Motorcraft SAE 80W-90Premium Rear Axle Lub
ENGINE DATAEngine 2.5L I4 engine 3.0L V6 engine 3.5L V6 engineCubic inches 151 182 214Required fuel 87 octane 87 octane 87 octaneFiring order 1-3-4-2
• 3.5L V6 Engine1. Short drivebelt is on first pulley groove closest to engine.2. Long drivebelt is on second pulley groove farthest from engine.IDENT
Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX
TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
Wheel locksFor maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle:• When adding a
FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on
Satellite Radio (if equipped)Satellite radio is available only with a valid SIRIUS radiosubscription. Check with your authorized dealer for availabili
Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With
2010 Fusion (fsn)Owners Guide, 1st PrintingUSA (fus)Ford Extended Service Plan331
AAccessory delay ...81AdvanceTrac ...206Air cleaner filter ...316–317, 319Air conditioningautoma
CCapacities for refilling fluids ...320CD ...29Cell phone use ...8Changing a
EElectronic message center ...19Emergencies, roadsidejump-starting ...254running out of fuel ...253, 303Emission co
flash to pass ...58high beam ...58replacing bulbs ...63turning on and o
Mirrors ...81–82automatic dimming rearviewmirror ...81heated ...
Seats ...110child safety seats ...157front seats ...113heated ...
WWarning lights (see Lights) ...12Washer fluid ...281Water, Driving through ...237Windowspower ...
CAT (Category) / FOLD (Folder): Press to toggle between turningthe most recently selected satellite radio category on or off. The categoryicon (CAT) w
Note: If there are no songs presently saved, the display will read NOSONGS.c. DELETE ALL SONGS: Press OK to delete all song’s from thesystem’s memory.
Sound AdjustmentsPress SOUND repeatedly to cycle through the following features:BASS: PressSEEK/TRACK to adjust the level of bass.TREBLE: PressSEEK/TR
(Phone): If your vehicle is equipped with SYNC, press to accessSYNC PHONE features. For further information, please refer to theSYNC information inclu
4. Turn the radio on, using either a tuned FM station or a CD loaded intothe system. Adjust the volume to a comfortable listening level.5. Turn the po
USB port (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdriver
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C
CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
Radio Display Condition Action RequiredACQUIRING Radio requiresmore than twoseconds toproduce audio forthe selectedchannel.No action required. Thismes
Radio Display Condition Action RequiredNO TEXT Categoryinformation notavailable.Category information notavailable at this time on thischannel. The sys
MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED)1. Fan speed adjustment: Turn to select fan speed.2.RRear defroster: Press to activate/deactiv
10. Recirculated air: Press to activate/deactivate air recirculationin the vehicle. Recirculated air may reduce the amount of time needed tocool down
For maximum cooling performance in MAX A/C mode:1. Select MAX A/C.2. Select the coolest temperature setting.3. Set the fan to the highest speed initia
recommended initial setting is between 72°F (22°C) and 75°F (24°C),then adjust for comfort. The driver side temperature setting will appearin the uppe
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
11. Recirculated air: Press to activate/deactivate air recirculationin the vehicle. Recirculated air may reduce the amount of time needed tocool down
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(NAVIGATION BASED – IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Messa
5. Passenger heated seat (if equipped): Press to control thepassenger heated seat. Refer to Heated and cooled seats in the Seatingand Safety Restraint
TOUCHSCREEN FUNCTIONSTemperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the Instrument Cluster chapter.Temper
VOICE COMMANDS IN CLIMATE MODEPlease refer to the Voice commands in climate mode section of theNavigation supplement for more information on using voi
To aid in side window defogging/demisting in cold weather:1. Select.2. Select A/C.3. Adjust the temperature control to maintain comfort.4. Set the fan
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the low beam headlampso
4. Turn the headlamp control to the autolamp position. The headlampswill turn on.5. Wait the desired amount of time for the exit delay you want (up to
High beamsPush the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate.Flash to passPull toward you slightly to acti
Note: If the battery is disconnected, discharged, or a new battery isinstalled, the dimmer control requires re-calibration. Press the dimmercontrol fr
BREAKING-IN YOUR VEHICLEYour vehicle does not need an extensive break-in. Try not to drivecontinuously at the same speed for the first 1,000 miles (1,
5. Locate the vertical adjuster oneach headlamp. Using a Phillips #2screwdriver, turn the adjuster eitherclockwise (to adjust down) orcounterclockwise
Your vehicle may also have readinglamps within the rear dome lamp(s).Press the switches on either side ofthe dome lamp to turn on thelamps.Ambient lig
• Large water droplets, drip marks or streaks present on the interior ofthe lensTake your vehicle to dealer for service if any of the above conditions
Replacing exterior bulbsCheck the operation of all the bulbs frequently.Replacing headlamp bulbs (2.5L/3.0L engines)High beam/low beam bulb replacemen
Low beam6. Disconnect the electrical connector.To install, reverse the removal procedure.For passenger side replacement of the high beam bulb, do thef
6. Disconnect the electricalconnector.7. Carefully pull bulb straight out ofsocket and install the new one.WARNING: Handle a halogen headlamp bulb car
3. Reaching through the wheel well,remove the rubber bulb accesscover from the housing.4. Remove the bulb socket by rotating it counterclockwise, then
Replacing headlamp bulbs (3.5L engine)High beam/low beam bulb replacementFor driver side replacement of the high beam/low beam bulbs, do thefollowing:
Replacing front parking lamp/turn signal bulbs (2.5L/3.0L engines)1. Make sure headlamp control is in the off position, then open the hood.2. Reach ov
Replacing front parking lamp/turn signal bulb (3.5L engine)For driver side replacement of the front parking lamp/turn signalbulb, do the following:WAR
Service Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This pote
For passenger side replacement of the front park/turn signal bulb, dothe following:1. Turn the steering wheel left to gain access to the wheel well.2.
Replacing rear side marker lampFor replacement of the rear side marker lamp, see your authorizeddealer.Replacing tail/brake/turn signal/backup lamp bu
Replacing high-mount brake lamp bulbYour vehicle is equipped with an LED center high-mount stop lamp. It isdesigned to last the life of the vehicle. I
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT/TELESCOPE STEERING WHEELTo adjust the steering wheel:1. Pull the lever down to unlock thesteering column.2. While the lever is in the downpositio
OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehicle’s overhead console will vary according toyour option package.Storage compartmentPress on
Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the on p
2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons.3. Slowly d
INSTRUMENT PANEL STORAGE COMPARTMENTThe storage compartment may beused to secure sunglasses or similarsized objects. Press the button toopen the stora
Always keep the power point caps closed when not being used.Cigar/Cigarette lighter (if equipped)Do not plug optional electrical accessories into the
To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access e
To operate ONE TOUCH DOWN:• Press the switch completely downto the second detent and releasequickly. The window will openfully. Momentarily press thes
Window lockThe window lock feature allows onlythe driver and front passenger tooperate the power windows.To lock out all the window controls(except fo
Do not clean the housing or glass of any mirror with harshabrasives, fuel or other petroleum-based cleaning products.Note: If equipped with a rear vie
Setting speed controlNote: The appearance of your vehicle’s speed control switchesmay vary according to your option package.The controls for using you
Resuming a set speedPress the RESUME control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed.Increasing speed whil
Turning off speed controlThere are two ways to turn off the speed control:• Press the OFF control.• Turn off the ignition.Note: When you turn off the
In any mode:• Press VOL + or VOL - to adjustthe volume.Navigation system hands freecontrol features (if equipped)Press and holdcontrol brieflyuntil th
Navigation system/SYNC handsfree control features(if equipped)Presscontrol briefly until thevoiceicon appears on theNavigation display to use the voic
Bounce-back:When an obstacle has been detected in the moon roof opening as themoon roof is closing, the moon roof will automatically open and stop at
POSITIVE RETENTION FLOOR MATWARNING: Do not install additional floor mats on top of thefactory installed floor mats as they may interfere with theacce
WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers use extreme caution
KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the lo
Recommended handling of the Integrated Keyhead Transmitter(IKT)To avoid inadvertently activating the remote entry functions of yourvehicle, it is reco
POWER DOOR LOCKS• Press thecontrol to unlock alldoors.• Press thecontrol to lock alldoors.Smart locksThis feature attempts to help prevent you from lo
Deactivating/activating autolock featureYour vehicle comes with the autolock features activated; there are fourmethods to enable/disable this feature:
4. Press and hold the 3 • 4. While holding the 3 • 4pressthe7• 8.5. Release the 7 • 8.6. Release the 3 • 4.The user should receive a horn chirp to ind
1. Place the key in the ignition andturn the ignition to the on position.2. Press the power door unlockcontrol on the door panel threetimes.3. Turn th
CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the
To open the luggage compartmentdoor (lid) from within the luggagecompartment, pull the illuminated“T” shaped handle and push up onthe trunk lid. The h
REMOTE ENTRY SYSTEMThe Integrated Keyhead Transmitter (IKT) complies with part 15 of theFCC rules and with RSS-210 of Industry Canada. Operation is su
2. Press and release again within five seconds to unlock all the doors.The remote entry system activates the illuminated entry feature; thisfeature tu
Commentaires sur ces manuels