Ford 2009 Explorer v.1 Manuel d'utilisateur

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 18Entertainment Systems 21How to get going 21AM/FM stereo with CD 25AM/FM stereo

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

O (off) — Rear wiper and washer off.For rear wash cycle, rotate (and hold as desired) the rear wiper/washercontrol to eitherposition.From either posit

Slide on rod featureRotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage.Note: To stow the visor back intoth

Installing a garage door opener (if equipped)The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers:• Pla

WARNING: Use only soft cups in the cupholder. Hard objectscan injure you in a collision.Rear center console features (if equipped)The rear center cons

To prevent the fuse from being blown, do not use the power point(s)over the vehicle capacity of 12 VDC/180W. If the power point or cigarlighter socket

Press and pull the window switchesto open and close windows.• Push down (to the first detent)and hold the switch to open.• Pull up (to the first deten

Bounce-Back (Driver’s window only)When an obstacle has been detected in the window opening as thewindow is moving upward, the window will automaticall

Automatic dimming interior rear view mirror (if equipped)Your vehicle may be equipped with an interior rear view mirror whichhas an auto-dimming funct

To adjust your mirrors:1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror.2. Mo

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is

• When this feature is enabled (AUTOMATIC), the running boards willimmediately move to the correct position based on the position of thedoors.Bounce-b

Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas

Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed.Increasing spee

Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal. This will not erase your vehicle’s previouslyset

In CD mode (if equipped):• PressSEEK to select the next selection on the CD/USBor press and hold to forward or reverse through the CD/USB.In DVD mode

Press to activate phone mode or answer a phone call. Press andholdto end call or exit phone mode.Pressto scroll through various menus and selections.

To open the moon roof: Press andrelease the SLIDE control, the moonroof will open automatically. Pressthe switch again to stop the moonroof.To close t

WARNING: When programming your HomeLink威 WirelessControl System to a garage door or gate, be sure that people andobjects are out of the way to prevent

Visor mount1. Position the end of your hand-held transmitter 1–3 inches (2–8 cm)away from the HomeLink威 button you wish to program while keeping thein

WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may

HomeLink威 should now activate your rolling code equipped device. Toprogram additional HomeLink威 buttons begin with Step 1 in this section.For question

Operating the HomeLink姞 Wireless Control SystemConsole mountVisor mountTo operate, simply press and release the appropriate HomeLink威 button.Activatio

Erasing HomeLink姞 buttonsConsole mountVisor mountTo erase the three programmed buttons (individual buttons cannot beerased):• Press and hold the two o

STANDARD MESSAGE CENTER (IF EQUIPPED)With the ignition in the on position,the message center, located on yourinstrument cluster, displaysimportant veh

DTE is calculated using a running average fuel economy, which is basedon your recent driving history of 500 miles (800 km). This value is notthe same

• Autounlock• Park Aid (if equipped)• Trailer sway control• Oil Life Reset and Start Value• Compass display• Compass zone adjustment• Compass calibrat

The sequence of the system check report and how it appears in themessage center is as follows:1. OIL LIFE2. CHARGING SYSTEM3. WASHER FLUID4. DOOR AJAR

AutolampThis feature keeps your headlights on for up to three minutes after theignition is switched off.1. To change the time delay of theautolamp fea

Reverse Sensing System (Park Aid) (if equipped)This feature sounds a warning tone to warn the driver of obstacles nearthe rear bumper, and functions o

3. Once “OIL LIFE SET TO 100%” isdisplayed, release, press and holdthe SELECT/RESET control switchfor more than two seconds tochange the Oil Life Star

Service engine soon: The serviceengine soon indicator lightilluminates when the ignition is firstturned to the on position to checkthe bulb and to ind

Compass zone adjustment (if equipped)1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn igniti

1. Start the vehicle.2. Locate the reset button on the compass sensor mounted on the baseof mirror.3. To calibrate, press and hold thereset button on

Warning display StatusDoor ajar Warning cannot be resetFuel level low Warning returns after 10 minutesPark brake engagedCheck brake systemCheck park a

CHECK FUEL FILL INLET (if equipped) — Displayed when the fuelfill inlet may not be properly closed. Refer to Easy Fuel™ “no cap” fuelsystem in the Mai

BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is lowand the brake system should be inspected immediately. Refer to Brakefluid in the Mainten

OPTIONAL MESSAGE CENTER (IF EQUIPPED)With the ignition in the on position,the message center, located on yourinstrument cluster, displaysimportant veh

Info menuThe Info menu items are shown onthe top two lines of the messagecenter. Press the INFO control todisplay the following:• Trip odometer (Trip

Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in miles/gallon or liters/km.If you calculate you

Fuel UsedSelecting this function from theINFO menu. “FUEL USED XXX.XGAL” will display the fuel used sincelast reset. The information displayedwill be

• Easy Entry/Exit Seat (if equipped)• Park Aid (if equipped)• Trailer sway control• Compass display• Compass zone adjustment• Compass calibration adju

• Optional instrument clusterBrake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when the

3. WASHER FLUID4. DOOR AJAR5. EXTERIOR LAMP6. BRAKE FLUID LEVEL7. PARK BRAKE8. FUEL LEVEL AND DISTANCE TO EMPTYUnits (English/Metric)1. Select this fu

1. To change the delay time of theautolamp feature, select thisfunction from the SETUP MENU.2. Press the RESET control to selectthe new Autolamp delay

Power Running Boards (if equipped)This feature automatically deploys the side running boards for easyentry/exit from the vehicle or for cleaning. Refe

1. To disable/enable the reversesensing system feature with thevehicle in P (Park), select thisfunction from the SETUP MENU orput the vehicle in R (Re

Compass zone adjustment (if equipped)1. Determine your magnetic zone byreferring to the zone map.2. Turn ignition to the on position.3. Start the engi

Compass calibration adjustmentPerform compass calibration in an open area free from steel structuresand high voltage lines. For optimum calibration, t

2. Press and hold the RESETcontrol for more than two seconds.Oil life is set to 100% and “OILCHANGE SET TO 100%” isdisplayed.Note: To change oil life

Warning display StatusDoor ajar Warning cannot be resetFuel level low Warning returns after 10 minutesPark brake engagedService RSC nowCheck brake sys

CHECK CHARGING SYSTEM — Displayed when the electrical systemis not maintaining proper voltage when the engine is running. If you areoperating electric

WASHER FLUID LEVEL LOW — Indicates the washer fluid reservoiris less than one quarter full. Check the washer fluid level. Refer toWindshield washer fl

Safety belt: Reminds you to fastenyour safety belt. A Belt-Minder威chime will also sound to remind youto fasten your safety belt. Refer tothe Seating a

POSITIVE RETENTION FLOOR MATWARNING: Do not install additional floor mats on top of thefactory installed floor mats as they may interfere with theacce

Cargo management systemThe cargo management system consists of storage compartments locatedin the floor of the rear cargo area.7 passenger stowage:1.

•To open the liftgate window, pressthe control on the remote entrytransmitter or, with the liftgateunlocked, push the control buttonon the right side

To adjust cross-bar position (ifequipped):1. Loosen the thumbwheel at bothends of the cross-bar (If thethumbwheel is too tight to releaseby hand, a sm

KEYSOne key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency.Your keys are programmed to your v

• Through your authorized dealer, or• Performing the power door lock control procedure, or• Performing the keyless entry keypad (if equipped) procedur

The user should receive a horn chirp to indicate the system has beendisabled or a chirp followed by a honk to indicate the system has beenenabled.Mess

1. Turn the ignition to the onposition.2. Press the power door unlockcontrol three times.3. Turn the ignition from the on tothe off position.4. Press

Power door lock/unlock inhibit feature (if equipped)If the key is not in the ignition, all doors are closed, and the vehicle hasbeen locked using the

CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the

Low tire pressure warning:Illuminates when your tire pressureis low. If the light remains on atstart up or while driving, the tirepressure should be c

The remote entry system allows youto lock or unlock all vehicle doorsand liftgate, open the liftgatewindow without a key and activatethe panic alarm.T

Locking the doors/liftgate1. Press and release to lock all the doors and liftgate. The lamps willflash. Note: If any door, the liftgate or the liftgat

2. Press the SET control on thelower-center portion of theinstrument panel.3. Within five seconds, press onecontrol on the remote transmitterand then

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery.Note: Please refer to localreg

3. Turn the key from the 1 (off)position to 3 (on).4. Cycle eight times rapidly (within10 seconds) between the 1 (off)position and 3 (on). Note: Theei

KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• open the liftgate window.• ac

• If you program a code to a position that already contains a set code,the previously-set code will be erased.Erasing personal code1. Enter the factor

Your vehicle comes with two coded keys; additional coded keys may bepurchased from your authorized dealer. The authorized dealer canprogram your spare

• The theft indicator will illuminate for three seconds and then go out.• If the theft indicator stays on for an extended period of time orflashes rap

5. Turn the ignition from the 1 (off) position to the 3 (on) position. Keepthe ignition in the 3 (on) position for at least three seconds, but no more

AdvanceTrac威: Flashes when theAdvanceTrac威 with RSC威 system isactive. Illuminates solid when thesystem has been disabled (by thedriver or as a result

SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting the front manual seat (if eq

Using the manual lumbar support (if equipped)For more lumbar support, turn thelumbar support control toward thefront of vehicle.For less lumbar suppor

WARNING: To reduce the risk of possible serious injury: Do nothang objects off seat back or stow objects in the seatback mappocket (if equipped) when

Press the control to recline theseatback forward or rearward.Using the power lumbar support (if equipped)The power lumbar control is located on the ou

A position can be recalled:• in any gearshift position if the ignition is not in the on position.• only in P (Park) or N (Neutral) if the ignition is

Deactivating/activating the easy access/easy out featureThe easy entry/exit feature can be turned off or on through the vehiclemessage center (if equi

The heated seat control is located in the lower center of the instrumentpanel.To operate the heated seats:• Push control to activate.• Push again to d

High beams: Illuminates when thehigh beam headlamps are turned on.Key-in-ignition warning chime: Sounds when the key is left in theignition in the off

If needed, when installing some high back child restraints, the headrestraints of the second row seating positions can be removed. Insert athin pointe

1. Lower the head restraints bypulling on the strap.2. Locate the recline handle situatedon the side of the seat cushion bythe door.3. Pull up on the

2. Lift up on the head restraint untilit locks into its original position.To return the seat to the upright position (E-Z entry equippedseats):1. Lift

Placing the 2nd row 60/40 seats in cargo mode (if equipped)The 2nd row seats can be placed in a kneel down load floor position toallow more cargo spac

Note: When folding down the seat, lift the handle only once. When theseatback releases and folds, the handle should be released. Any furtherturning of

Note: If the seat back will not return to the upright position, tumble theseat again and re-latch it to the floor. Be sure that cargo or other objects

Exiting the 3rd row1. Lower the head restraints. SeeFolding down the 2nd row 60/40seats and buckets seats earlier inthis section.2. Pull on the lever/

WARNING: Before returning the seatback to its originalposition, make sure that cargo or any objects are not trappedbehind the seatback. After returnin

Push the top of the control buttonto return the seatback to its originalposition.The power fold down seats will operate for 30 minutes after theigniti

• Driver’s seat position sensor.• Front passenger sensing system• “Passenger airbag off” or “pass airbag off” indicator lamp• Front crash severity sen

Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,

Driver’s seat position sensorThe driver’s seat position sensor allows your Personal Safety System威 totailor the deployment level of the driver dual-st

Front safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly ag

Safety restraints precautionsWARNING: Always drive and ride with your seatback uprightand the lap belt snug and low across the hips.WARNING: To reduce

WARNING: Safety belts and seats can become hot in a vehiclethat has been closed up in sunny weather; they could burn asmall child. Check seat covers a

• Front and rear seats2. To unfasten, push the release button and remove the tongue from thebuckle.• Front and rear seatsAll safety restraints in the

Automatic locking modeWhen to use the automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to

WARNING: After any vehicle collision, the combination lap andshoulder belt system at all passenger seating positions must bechecked by an authorized d

Front safety belt height adjustmentYour vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shou

To adjust the comfort guide:1. Slip the shoulder belt into thebelt guide.2. Slide the guide up or down alongthe webbing so that the belt iscentered on

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war

Locks and Security 154Keys 154Locks 154Anti-theft system 160Seating and Safety Restraints 170Seating 170Safety restraints 188Airbags 204Child restrain

Trip odometer: Registers the miles (kilometers) of individual journeys.• Standard instrument clusterPress the SELECT/RESET controlonce to switch from

The Belt-Minder威 feature uses two different warning chimes. During thefirst minute of activation, the warning chime will sound once everysecond. The r

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra

Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate

The driver and front passenger Belt-Minder威 features can bedeactivated/activated by performing the following procedure:Before following the procedure,

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

WARNING: Never place your arm over the airbag module as adeploying airbag can result in serious arm fractures or otherinjuries.To properly position yo

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

• one or more impact and safing sensors.• a readiness light and tone.• diagnostic module.• and the electrical wiring which connects the components.• F

The front passenger sensing system will turn off the passenger seat sideairbag if:• the seat is empty and safety belt is unbuckled.The front passenger

AUDIO SYSTEMSQuick start — How to get goingWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly

• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LampPasseng

ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase,

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi

A difficulty with the system is indicated by one or more of the following:• The readiness light will eitherflash or stay lit.• The readiness light wil

How does the side airbag system work?The design and development of the side airbag system includedrecommended testing procedures that were developed b

WARNING: Several air bag system components get hot afterinflation. Do not touch them after inflation.WARNING: If the sideairbag has deployed, theairba

WARNING: All occupants of the vehicle including the drivershould always wear their safety belts even when an airbag SRSand Safety Canopy威 system is pr

Children 12 years old and under should always be properly restrained inthe second or third row seats (if equipped). The Safety Canopy威 will notinterfe

Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref

SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme

Listening to satellite radio (if equipped)1. If the audio system is turned off,press VOL-PUSH to turn the radioon. Turn VOL-PUSH to adjust thevolume.N

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeSmallchildrenChildren who have outgrown o

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method asindicated below by “X”LATCH(lowe

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestr

Installing child safety seats with combination lap and shoulderbeltsIf needed, when installing some high back child restraints, the headrestraints of

• Keep the buckle release button pointing up and away from the safetyseat, with the tongue between the child seat and the release button,to help preve

3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi

8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up

however the safety belt can still be used to attach the child seat. Forforward-facing child seats, the top tether strap must also be attached tothe pr

The LATCH anchors for child seatinstallation are located at the rearsection of the second row seatbetween the cushion and seatback.The LATCH anchors a

For a single CD system, if a discis not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the

Use of inboard lower anchors from the outboard seating positions(center seating use)The lower anchors at the center of the second row rear seat are sp

Attaching child safety seats with tether strapsMany forward-facing child safety seats include a tether strap whichextends from the back of the child s

Perform the following steps to install a child safety seat with tetheranchors:1. Route the tether strap under the head restraint and between the headr

3. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theeven

When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the

Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

Move a child to a different seating location if the shoulder belt does notstay positioned on the shoulder during use.Follow all instructions provided

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary

Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random pl

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

Glossary of tire terminology• Tire label: A label showing the OE (Original Equipment) tire sizes,recommended inflation pressure and the maximum weight

Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure of all tires and adjust ifrequired

When weather temperature changes occur, tire inflation pressures alsochange. A 10°F (6°C) temperature drop can cause a corresponding dropof 1 psi (7 k

TIRE CAREInspecting your tiresPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones, nails or glass that

WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressur

WARNING: Only use replacement tires and wheels that are thesame size, load index, speed rating and type (such as P-metricversus LT-metric or all-seaso

It is recommended that the two front tires or two rear tires generally bereplaced as a pair.The tire pressure sensors mounted in the wheels (originall

Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your

AM/FM Single CD/MP3 satellite compatible sound system(if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and

Note: If your tires show uneven wear ask an authorized dealer to checkfor and correct any wheel misalignment, tire imbalance or mechanicalproblem invo

4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new

8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n

Label or Tire Label which is located on the B-Pillar or the edge of thedriver’s door. The cold inflation pressure should never be set lower thanthe re

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti

When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.

Low TirePressureWarning LightPossiblecauseCustomer Action RequiredFlashing WarningLightSpare tire inuseYour temporary spare tire is in use.Repair the

In CATEGORY MODE, press / to scroll through the list ofavailable SIRIUS channel Categories (Pop, Rock, News, etc.). Refer toCategory Mode under Menu f

SNOW TIRES AND CHAINSWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. The use ofnon-recommende

your vehicle, familiarize yourself with the following terms for determiningyour vehicle’s weight ratings, with or without a trailer, from the vehicle’

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or performance, e

WARNING: Do not use replacement tires with lower loadcarrying capacities than the original tires because they maylower the vehicle’s GVWR and GAWR lim

• A final example for your vehicle with 1,400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the

2. Weigh your vehicle without cargo. To obtain correct weights, take yourvehicle to a shipping company or an inspection station for trucks.3. Subtract

4x2GCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.0L SOHC Class

4X4 and AWDGCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.6L* C

• DELETE SONG: Press OK to delete a song from the system’smemory. Press/ to cycle through the saved songs. When thesong appears in the display that yo

Class III Trailer Hitch Safety ChainLoops can be used as recoveryhooks.Do not attach safety chains to the bumper.Trailer brakesElectric brakes and man

Driving while you towWhen towing a trailer:• To ensure proper “break-in” of powertrain components, do not trailertow during the first 1,000 miles (1,6

• If you will be towing a trailer frequently in hot weather, hillyconditions, at GCWR, or any combination of these factors, considerrefilling your rea

RECREATIONAL TOWINGFollow these guidelines if you have a need for recreational (RV) towing.An example of recreational towing would be towing your vehi

STARTINGPositions of the ignition1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accesso

WARNING: If you smell exhaust fumes inside your vehicle, haveyour dealer inspect your vehicle immediately. Do not drive if yousmell exhaust fumes.Impo

• Make sure the gearshift is in P(Park).3. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminate. See

Starting the engine1. Turn the key to 3 (on) withoutturning the key to 4 (start). If thereis difficulty in turning the key,rotate the steering wheel u

ENGINE BLOCK HEATER (IF EQUIPPED)An engine block heater warms the engine coolant which aids in startingand allows the heater/defroster system to respo

• Be sure that areas where the vehicle is parked are clean and clear ofall combustibles such as petroleum products, dust, rags, paper andsimilar items

To activate, press MENU repeatedly until RBDS (ON/OFF) appears inthe display. Use/ / SEEK to toggle RBDS ON/OFF. WhenRBDS is OFF, you will not be able

Four-wheel anti-lock brake system (ABS)Your vehicle is equipped with an Anti-lock Braking System (ABS). Thissystem helps you maintain steering control

Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.ADVANCETR

WARNING: If a failure has been detected within theAdvanceTrac威 with RSC威 system, the ⬙sliding car⬙ icon willilluminate steadily. Verify that the Advan

When AdvanceTrac威 with RSC威 performs a normal system self-check,some drivers may notice a slight movement of the brake, and/or arumble, grunting, or g

Electronic Stability Control (ESC)Electronic Stability Control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa

Switching Off AdvanceTrac威 with RSC威If the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off certain features of the

WARNING: Trailer sway control does not prevent a trailer fromswaying, it mitigates the sway from increasing once it hasoccurred. If you are experienci

• Do not fill the power steering pump reservoir above the MAX mark onthe reservoir, as this may result in leaks from the reservoir.If the power steeri

AUTOMATIC TRANSMISSION OPERATIONBrake-shift interlockThis vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever fr

TRACK/FOLDER MODE: Available only on MP3 discs in CD mode.In track mode, pressSEEK, SEEK to scroll through all tracks onthe discIn folder mode, pressS

Driving with a 5–speed automatic transmission (if equipped)This vehicle is equipped with an Adaptive Transmission Control Strategy.This Adaptive Trans

P (Park)This position locks the transmissionand prevents the rear wheels fromturning.To put your vehicle in gear:• Start the engine• Depress the brake

D (Drive) without OverdriveOverdrive can be deactivated bypressing the transmission controlswitch on the side of the gearshiftlever.• This position al

Forced downshifts• Allowed in D (Overdrive) or Drive.• Depress the accelerator to the floor.• Allows transmission to select an appropriate gear.Drivin

P (Park)This position locks the transmissionand prevents the rear wheels fromturning.To put your vehicle in gear:• Depress the brake pedal• Start the

D (Drive) without OverdriveOverdrive can be deactivated bypressing the transmission controlswitch on the side of the shift lever.• This position allow

• Allows upshifts by moving gearshift lever.• Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds

WARNING: Certain add-on devices such as large trailer hitches,bike or surfboard racks and any device that may block thenormal detection zone of the re

Audible WarningsDistance to Object WarningSpeed above 2.5 mph (4 km/h)up to 1.6 feet (.5 meters) Solid1.6 feet (.5 meters) to 3.1 feet(1 meter)Fast be

The radar sensor is located behind the rear bumper/fascia. Alwayskeep the rear bumper/fascia free from snow, ice and largeaccumulations of dirt. These

Customer Assistance 339Reporting safety defects (U.S. only) 346Reporting safety defects (Canada only) 346Cleaning 347Maintenance and Specifications 35

In satellite radio mode (if equipped), press SEEK, SEEK toseek to the previous/next channel. If a specific category is selected,(Jazz, Rock, News, etc

Using the Control Trac 4WD system4X4 AUTO - Provides electronically-controlled four-wheel drive withpower delivered to all four wheels as required for

WARNING: If your vehicle is equipped with AWD, a spare tire ofa different size than the road tires should never be used. Such atire could make the veh

Driving off-road with truck and utility vehiclesAWD and 4WD vehicles are specially equipped for driving on sand, snow,mud and rough terrain and have o

• It often may be less risky to strike small objects, such as highwayreflectors, with minor damage to your vehicle rather than attempt asudden return

Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,

ParkingOn some 4WD vehicles, when the transfer case is in the N (Neutral)position, the engine and transmission are disconnected from the rest ofthe dr

Mud and waterIf you must drive through highwater, drive slowly. Traction orbrake capability may be limited.When driving through water,determine the de

possibly rolling over. Whenever driving on a hill, determine beforehandthe route you will use. Do not drive over the crest of a hill withoutseeing wha

Avoid sudden applications of power and quick changes of direction onsnow and ice. Apply the accelerator slowly and steadily when startingfrom a full s

DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th

9. FOLDER: In folder mode,pressFOLDER to access theprevious folder on MP3 discs, ifavailable.10. FF (Fast forward): Press FFto manually advance in a C

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co

FUEL PUMP SHUT-OFF SWITCHFUELRESETThe fuel pump shut-off switch is a device intended to stop the electricfuel pump when your vehicle has been involved

FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth

Passenger compartment fuse panelThe fuse panel is located below theinstrument panel on the driver’sside.To remove a fuse use the fuse puller tool prov

Fuse/RelayLocationFuse AmpRatingProtected Circuits5 5A Moon roof, Door lock switchillumination, Rearview mirror withmicrophone6 20A Liftglass release

Fuse/RelayLocationFuse AmpRatingProtected Circuits22 15A Brake switch, Bi-color stop lamps,CHMSL, All turn lamps23 15A Interior lamps, Puddle lamps,Ba

Power distribution boxThe power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protec

The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 50A** BATT 2 (SJB)2 50A** BATT 3 (SJB)3 50A** BATT 1 (

Fuse/RelayLocationFuse AmpRatingProtected Circuits14 30A** Memory seats (DSM)40A** Non-memory seats15 40A** Rear defrost, Heated mirrors16 40A** Front

In satellite radio mode (if equipped), press and hold to hear a briefsampling of the next channels. Press again to stop. In CATEGORYMODE, press SCAN t

Fuse/RelayLocationFuse AmpRatingProtected Circuits40 15A* Fan clutch, PCV valve, AC clutchrelay, GCC fan41 15A* SDARS, DVD, SYNC42 15A* Redundant brak

CHANGING THE TIRESIf you get a flat tire while driving:• do not brake heavily.• gradually decrease the vehicle’s speed.• hold the steering wheel firml

A dissimilar spare tire/wheel is defined as a spare tire and/or wheel thatis different in brand, size or appearance from the road tires and wheelsand

The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following:• Handling, stability and braking performance• Comfort and

Location of the spare tire and toolsThe spare tire and tools for your vehicle are stowed in the followinglocations:Tool LocationSpare tire Under the v

Removing the spare tireDo not use an impact wrench on the winch drive nut. This willdamage the spare tire winch.1. Open the cover from the carpeting o

3. Turn the wrenchcounterclockwise until the tire islowered to the ground and the cablehas slack. When turning the wrench,make sure that it does not s

1. Block the wheel that is diagonallyopposite of the flat tire using thewheel chock provided with yourvehicle.2. Use the tip of the lug wrench toremov

5. Position the jack according to theillustrated guides and turn the jackhandle clockwise until the tire is amaximum of 1 inch (25 mm) off theground.N

9. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torquespecifications later in this chapterfor the proper lu

Audiophile AM/FM in-dash six CD/MP3 satellite compatible soundsystem (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontr

Re-stowing the jack and tools1. Unblock the wheels.2. Stow the wheel ornament (if removed) in a safe location in the vehicle(such as the glove box or

Note: Inspect the wheel pilot holeprior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean r

Preparing your vehicleWhen the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

4. Make the final connection of the negative (-) cable to the ground studlocated toward the front of the vehicle (forward of the battery) on theradiat

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa

4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery.After the disabled vehicle has been started and the jumper

WRECKER TOWINGNote: Turn off the power running boards (if equipped) prior topreparing the vehicle for towing. Refer to Running boards in the DriverCon

On 4x4/AWD vehicles, it is required that your vehicle be towed with awheel lift and dollies or flatbed equipment with all the wheels off theground.If

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In satellite radio mode (if equipped), press / to tune to thenext/previous channel.In CATEGORY MODE, press/ to scroll through the list ofavailable SIR

In Canada:Mailing Address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.

ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent qu

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

• DELETE SONG: Press OK to delete a song from the system’smemory. Press/ to cycle through the saved songs. When thesong appears in the display that yo

4.6L V8 ENGINEPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authorized

special solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade and windshield from automated carwash facilities

2. Apply Motorcraft Deluxe Leather and Vinyl Cleaner (ZC-11-A) [InCanada use Motorcraft Multi-Purpose Cleaner (CXC-101)] to the wipedarea and spread a

• To help maintain its resiliency and color, use the Motorcraft DeluxeLeather Care Kit (ZC-11-D), available from your authorized dealer. InCanada, use

Motorcraft Premium Glass Cleaner (Canada only) (CXC-100)Motorcraft Premium Liquid Wax (ZC-53-A)Motorcraft Premium Windshield Washer Concentrate (U.S.

SERVICE RECOMMENDATIONS• Use the scheduled maintenance information to track routineservice.• Use only recommended fuels, lubricants, fluids and servic

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.0L SOHC V6 engine1. Engine oil filler cap2. Engine oil dipstick (out of view)3. Brake fluid reservoi

4.6L V8 engine1. Air filter assembly2. Engine oil filler cap3. Engine oil dipstick4. Brake fluid reservoir5. Power distribution box6. Battery7. Power

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

RBDS: Available only in FM mode. This feature allows you to searchRBDS-equipped stations for a certain category of music format:CLASSIC, COUNTRY, INFO

CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas

4. To attach the new wiper to thewiper arm, align the cross pin andkeyway (denoted with the arrows)and firmly press the wiper bladeinto the wiper arm

• 4.6L V8 engine6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil level is between the lower and upper holes, t

• 4.6L V8 engine• Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized dealer.7. Put the

Engine Oil Recommendations4.0L V6 EngineLook for this certificationtrademark.Use SAE 5W-30 engine oilOnly use oils “Certified For Gasoline Engines” by

4.6L 3V V8 EngineLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by the AmericanPetroleum

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

• 4.0L V6 engine• 4.6L V8 engine• The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant

TRACK/FOLDER MODE: Available only on MP3 discs in CD mode.In track mode, pressSEEK, SEEK to scroll through all tracks onthe discIn folder mode, pressS

Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. When the engine is cool, add the mixtu

For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when

Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage.Recycle

• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damag

Along with the (Engine coolant temperature) indicator, the enginecoolant temperature gauge will read in the Hot (H) area.Oil overheat can be triggered

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsWARNING: Do not overfill the fuel tank. The pressure in anoverfilled tank may c

• Fuels can also be harmful if absorbed through the skin. If fuel issplashed on the skin and/or clothing, promptly remove contaminatedclothing and was

Use the following guidelines to avoid electrostatic charge build-up whenfilling an ungrounded fuel container:• Place approved fuel container on the gr

WARNING: The fuel system may be under pressure. If you heara hissing sound near the fuel filler door (Easy Fuel™ “no cap”fuel system), do not refuel u

Fuel qualityIf you are experiencing starting, rough idle or hesitation driveabilityproblems, try a different brand of unleaded gasoline. “Premium”unle

5. SEEK: In radio and CD/MP3mode, press to access the previous() or next ( ) strong stationor track.In satellite radio mode (if equipped), pressSEEK t

Refilling with a portable fuel containerWith the Easy Fuel™ “no cap” fuel system, use the following directionswhen filling from a portable fuel contai

ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform

Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers).2. Each time you fill the tan

• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between the top gears occurs. Unnecessaryshifting of this type co

EPA fuel economy estimatesEvery new vehicle should have a window sticker containing EPA fueleconomy estimates. Contact your authorized dealer if the w

WARNING: Exhaust leaks may result in entry of harmful andpotentially lethal fumes into the passenger compartment.Do not make any unauthorized changes

If the Service engine soon indicator remains on, have your vehicleserviced at the first available opportunity. Although some malfunctionsdetected by t

POWER STEERING FLUIDCheck the power steering fluid. Refer to scheduled maintenanceinformation for the service interval schedules.1. Start the engine a

TRANSMISSION FLUIDChecking automatic transmission fluidThe automatic transmission does not have an underhood transmissionfluid dipstick.Refer to your

3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening.Use only fluid that meets Ford specifications

8. FOLDER : In folder mode,press FOLDERto access nextfolder on MP3 discs, if available.9.FOLDER: In folder mode,press FOLDER to access theprevious fol

Changing the air filter element• 4.0L Engine• 4.6L Engine1. Release the clamps that secure the air filter housing cover.2. Carefully separate the two

MOTORCRAFT PART NUMBERSComponent 4.0L SOHC V6 engine 4.6L 3V V8 engineAir filter element FA-1695 FA-1780Fuel filter FG-1083 FG-1083Battery BXT-65-650

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord Part Name orequivalentFord Part Number / FordSpecificationBrake fluidBetween MINand

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationEngine coolant 4.0Lengine withoutauxiliary climatecontrol12.2 quarts(11.5L

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationEngine oil 4.6Lengine6.0 quarts(5.7L)Motorcraft SAE5W-20 PremiumSynthetic

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationTransfer case fluid(AWD)1.3 quarts(1.25L)Motorcraft TransferCase FluidXL–1

ENGINE DATAEngine 4.0L SOHC V6engine4.6L 3V V8engineCubic inches 245 281Required fuel 87 octane 87 octaneFiring order 1-4-2-5-3-6 1-3-7-2-6-5-4-8Ignit

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

Satellite radio is available only with a valid SIRIUS radiosubscription. Check with your authorized dealer for availability.In TEXT MODE, sometimes th

Roof rail cross barsTrailer hitch drawbars, wiring harnesses and accessoriesTripTunes™ Advanced portable audio connectionPeace of mindMobile-Ease™ han

AAccessory delay ...107AdvanceTrac ...282Air cleaner filter ...389–391Air conditioning ...

Cleaning your vehicleengine compartment ...349instrument panel ...351interior ...352plas

lubrication specifications ...392refill capacities ...392service points ...357–358starting after a collision .

Hood ...356How to get going ...21IIgnition ...274, 396Illumina

Oil (see Engine oil) ...361PParking brake ...281Parts (see Motorcraft parts) ...391Passenger OccupantClassifi

SecuriLock passive anti-theftsystem ...166Setting the clockAM/FM single CD ...27AM/FM/In-dash 6

power ...105rear wiper/washer ...101Windshield washer fluid andwipers ...

18. (CD eject): To eject a discfrom the system, press. Selectthe correct slot number usingmemory presets 1–6. When ready, the system will eject the di

2. An audio extension cable with stereo male 1/8 in. (3.5 mm)connectors at each endTo play your portable music player using the auxiliary input jack:1

moving. Also, the portable music player should be stored in a securelocation, such as the center console or the glove box, when the vehicle isin motio

CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m

Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The

Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti

Your vehicle may be equipped with a Family Entertainment System(FES) which allows you to listen to audio CDs, MP3 discs, watch DVDsand to plug in and

Press the power button to turn thesystem off. The indicator light willturn off indicating the system is off.Note: The audio from the DVD system will p

3. The disc will begin to play andthe ‘MP3 Audio Disc’ screen willdisplay and allow you to access theCOMPRESSION, SHUFFLE, SCANand FOLDER MODE feature

from the auxiliary source, the screen will remain black. If the videosource is set to DVD-AUX, the display will automatically turn on if avideo signal

1. Press theheadphone/speaker/ buttonon the DVD player or press the 2and 4 memory presets on the radio at the same time.A green light will illuminate

To adjust display brightness:To decrease/increase the brightnesslevel on the display screen, pressthe brightness control on the DVDsystem. A display w

2. / (Stop/Eject): Pressonce to stop and press a secondtime to eject a disc from the DVDsystem.3.(Reverse): Press andrelease for the previous chapter

10. Volume: When in Single Play,press to increase () or decrease( ) the volume over all speakers.When in Dual Play, press to increase() or decrease (

15. ENTER: Press to select/confirmthe current selection.16. Cursor /Brightness controls:Use the cursor controls to makevarious selections when in anym

1. Power control: Press to turn the FES (Family EntertainmentSystem) ON/OFF.2. Cursor controls: Use in various active menus to advance the cursorup/do

Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance

8. Fast Forward/Next: In DVD mode, press and hold for a quickadvance within the DVD. Press and release to advance to the nextchapter. In CD/MP3 mode,

Battery replacementBatteries are supplied with the remote control unit. Since all batterieshave a limited shelf life, replace them when the unit fails

HeadphonesWireless headphonesWARNING: The driver should never use the headphones whiledriving the vehicle. Using headphones may prevent the driverfrom

To install the batteries, remove the screw at the bottom of the cover.Then, lightly press down on top and slide the cover off.When replacing the batte

To operate the headphones:• Press POWER on the ear piece to turn on the headphones. A redindicator light will illuminate indicating the headphones are

Wired headphonesWARNING: Do not leave children unattended in the vehicle anddo not let children operate the system while unsupervised. Ifwired headpho

Single Play: Single play consists of all occupants in the vehicle listeningto the same playing media over the front and rear speakers. When theDVD sys

Press MEDIA to change the audiosource for Channel A. Thisinformation will display on the DVDsystem screen.Press the Headphone Control buttonB to chang

Press MEDIA to change the audiosource for Channel A. Thisinformation will display on the DVDsystem screen.Press the Headphone Control buttonB to chang

Menu modePress MENU once on the DVD system to access the DVD disc menu ifavailable.Press MENU twice to access the DVD set-up menu and the followingfea

Event Data RecordingOther modules in your vehicle — event data recorders — are capable ofcollecting and storing data during a crash or near crash even

You can select from: WIDE, LETTERBOX or PAN SCAN. Once you havemade your selection, press ENTERto confirm. The LCD screen displaywill immediately chan

Once you have made your selection,press ENTER to confirm. This isdisc dependent.Audio CDsTo play audio CDs on your DVD system:1. Ensure that the vehic

4. The folder, track and elapsedtime will appear in the status bar.The screen will list the Artist, Title,Album and File Name.COMP (Compression):Compr

CD, MP3 and CD player care• Handle discs by their edges only. Never touch the playing surface.• Do not expose discs to direct sunlight or heat sources

4. Use the DVD bezel controls to:Press to play or pause a DVD.Press to stop or eject a DVD.Press and release to go to theprevious chapter. Press and h

2. Press the right cursor button. TheDVD will advance one frame. Eachpress of the right cursor button willadvance the DVD video by oneframe.Headphone/

Audio displaysYour DVD system interacts closely with the front audio system. Statusmessages will appear in the radio display showing the DVD status. S

When the DVD system is ON, youcan then press the memory presetcontrols 2 and 4 simultaneously totoggle between Single Play and Dual Play. In Single Pl

Safety informationWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers us

Do not operate video games or video equipment if the power cordsand/or cables are broken, split or damaged. Carefully place cords and/orcables where t

Using your vehicle with a snowplowDo not use this vehicle for snowplowing.Your vehicle is not equipped with a snowplowing package.Using your vehicle a

Temperature extremesWhen the vehicle is parked under direct sunlight or in an extremely coldplace for a long period of time, wait until the cabin temp

While operating in Headphone Only Mode, the system will have limitedfunctionality.• The system will only output audio to the headphones. It will not b

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele

• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield.• To improve the A/C cool down when the vehicle interior issign

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM(IF EQUIPPED)1. A/C control: Manually turns A/Con or off.2. Recirculation control: Coolsthe vehicle mo

6. : Distributes outside air through the windshield defroster vents.7.: Distributes outside air through the windshield defroster ventsand floor vents.

17. Temperature conversion:Press to toggle between Fahrenheitand Celsius temperature on theDATC display only. The set point temperatures in Celsius wi

AUXILIARY SYSTEM (IF EQUIPPED)Your vehicle may be equipped with an auxiliary climate system. Theseauxiliary controls, located in the overhead console,

REAR WINDOW DEFROSTERThe rear defroster control is locatedon the instrument panel.Press the rear defroster control toclear the rear window of thin ice

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola

Export unique (Non–United States/Canada) vehicle specificinformationFor your particular global region, your vehicle may be equipped withfeatures and o

Fog lamp controlThe fog lamps can be turned ononly when the headlamp control isin the, or position andthe high beams are not turned on.Pull headlamp c

Flash to passPull the lever toward you toactivate. Release the lever todeactivate.PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument pa

Headlamp aim adjustmentThe headlamps on your vehicle can only be vertically adjusted. Yourvehicle does not require horizontal aim adjustments.To adjus

TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSDome/reading lampsThe dome lam

Cargo/reading lampsThe dome portion of the lamp orthe center light can be turned onwhen the panel dimmer control isrotated fully up or when a door iso

Function Number of bulbs Trade numberHeadlamp low & highbeam2H13Front park/turn lamp 2 3457 NAK (amber)Side park/turn lamp 2 194Upper rear tail la

Replacing headlamp bulbsDo not touch the glass of a halogen bulb.1. Turn off the headlamps and openthe hood.2. Remove three screws from theheadlamp as

Replacing front parking lamp/turn signal/sidemarker bulbs1. Turn off the headlamps and openthe hood.2. Remove three screws from theheadlamp assembly a

4. Rotate the bulb socketcounterclockwise and remove itfrom the lamp assembly.5. Pull the bulb straight out of thesocket.Reverse steps to reinstall bu

Replacing high-mount brakelamp bulb1. Remove the two screws and lampassembly away from the vehicle.2. Remove the bulb holder from thelamp assembly by