Ford 2005 Mustang v.2 Manuel d'utilisateur Page 45

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 248
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 44
Bounce Back Override (Front windows only)
To override Bounce Back, within 2 seconds after reaching Bounce Back
position, if the switch is moved from the Neutral to the Express Up
position the window will travel up with no bounce back protection.
If the switch is released before the window reaches fully closed position,
the window will stop. For example: Bounce Back Override can be used to
overcome the resistance of ice on the window or seals.
Restoring the Express up functionality (Front windows only)
Under low battery power conditions, Express Up only functionality may
be lost. To reset this function after restoring full battery power, pull the
switch to the Express Up position, hold the switch until the glass
reaches the stall position and continue to hold for 2 seconds. Push the
window switch DOWN and operate the window to the full down position.
Express UP will now be functional. Perform Express UP
re-calibration with door closed only. Calibrating with door open
will cause the window to continuously bounce back.
Short drop glass (Front windows only)
In order to improve door efforts and sealing, your vehicle is equipped
with short drop glass. This feature lowers the glass when either door is
opened. The glass returns to its closed position when the door is closed.
Proper operation of the short drop glass requires that the windows be
calibrated. Though your windows will have been calibrated before
your vehicle is delivered to you, it is possible for the windows to
lose calibration. If a window loses its calibration, your short drop
feature will lower the window, but will not raise it again when the door is
closed. To re-calibrate the window, pull the switch up to raise the
window until it completes its travel and hold the switch up for 2
seconds. Another possible effect of lost calibration is that the feature
may not lower the window. To re-calibrate the window in this case, lower
the window until it completes its travel and hold the switch down for 2
seconds. Immediately after releasing the window down switch, pull the
switch up to raise the window until it completes its travel and hold the
switch up for 2 seconds. Perform Short drop re-calibration with
doors closed only. Re-Calibrating with doors open will cause the
window to continuously bounce back.
Rear Power Windows (Convertible Only)
The rear quarter windows are operated by a single window switch
located at the Driver door window controls. Press and pull the window
switch to open and close the windows.
2005 05+ Mustang (197)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
45
Vue de la page 44
1 2 ... 40 41 42 43 44 45 46 47 48 49 50 ... 247 248

Commentaires sur ces manuels

Pas de commentaire

Furuno FELCOM 250 manuály

Uživatelské manuály a uživatelské příručky pro Hardware Furuno FELCOM 250.
Poskytujeme 1 manuály pdf Furuno FELCOM 250 ke stažení zdarma podle typů dokumentů: Uživatelský manuál


Furuno FELCOM 250 Uživatelský manuál (66 strany)


Značka: Furuno | Kategorie: Hardware | Velikost: 6.46 MB |

 

Tabulka s obsahem

Installation Manual

1

INMARSAT FLEETBROADBAND

1

FELCOM 250/FELCOM 500

1

A : AUG 2009

2

H : FEB . 18, 2011

2

Pub. No. IME-56660-H

2

(YOSH ) FELCOM500/250

2

SAFETY INSTRUCTIONS

3

SYSTEM CONFIGURATION

4

EQUIPMENT LISTS

5

1. HOW TO INSTALL THE UNIT

7

MICROWAVE RADIATION !

8

NO ADMITTANCE WITHIN 1.40 m

8

NO ADMITTANCE WITHIN 0.7 m

9

Pressure

10

(Above figure: FELCOM 500)

10

FELCOM 500

11

FELCOM 250

11

Procedure

12

1. HOW TO INSTALL THE UNIT

13

Name Type Code no. Qty

17

1.2 Communication Unit

18

1.3 IP Handset

19

(0.59")

20

90±0.5 (3.54")

20

120 (4.72")

20

132±0.5 (5.20")

21

144 (5.67")

21

127±1 (5.00")

21

Fixing plate (left)

22

Fixing plate (right)

22

Six places

22

Facsimile

22

How to change modem settings

23

Mounting location

23

How to mount

24

Remove plastic sheet and

25

2. CONNECTIONS

26

2.2 Antenna Cable

27

2. CONNECTIONS

28

12DSFA-CF as follows

29

2.3 Communication Unit

30

TTYCS-1 Cable fabrication

31

NMEA signal, External alarm

31

Cable fixture

32

Never connect as follows:

33

How to inset the grommet

34

Unit to affix

35

2.6 LAN Cable Fabrication

36

3. SETTING AFTER INSTALLATION

37

Administrator Login

38

Basic settings

39

Settings

39

3.2 GPS Setting

40

3.3 Analog Port Setting

41

Incoming Indicator

42

3.5 Serial Port Setting

43

3.6 Satellite Setting

44

3.7 OTA Setting

45

3.8 Handset Setting

46

Setting in the IP handset

47

APPENDIX 1 JIS CABLE GUIDE

50

㧼㧭㧯㧷㧵㧺㧳ޓ㧸㧵㧿㨀

51

+056#..#6+10/#6'4+#.5

52

Modular jack box

55

8/Mar/10 R.Esumi

57

11/Dec/09 R.Esumi

58

17/May/2010 TAKAHASHI

59

11/May/09 R.Esumi

61

18/Feb/09 R.Esumi

62

Y. Hatai

64

T.Matsuguchi

65

Y.NISHIYAMA

66





Další produkty a příručky pro Hardware Furuno

Modely Typ Dokumentu
ETR-30N Uživatelský manuál   Furuno ETR-30N User Manual, 48 stránky