Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 13Entertainment Systems 15AM/FM stereo cassette 15AM/FM stereo with CD 18CD cha
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa
Lap beltsAdjusting the center front lap beltThe center front lap belt does not adjust automatically.The lap belt should fit snugly and as low as possi
Before you reach and latch a combination lap and shoulder belt havingan adjust tongue into the buckle, you may have to lengthen the lap beltportion of
Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occup
If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2 minutesh
Reasons given... Consider...“Belts are uncomfortable” We design our safety belts to enhancecomfort. If you are uncomfortable -try different positions
Do not sit on top of a buckled safety belt to avoid theBeltMinder娂 chime. Sitting on the safety belt will increase therisk of injury in an accident. T
2. Wait until the safety belt warning light turns off. (Approximately 1minute)• Step 3 must be completed within 50 seconds after the safety beltwarnin
belt height adjusters (if equipped), shoulder belt guide on seatback (ifequipped), child safety seat LATCH and tether anchors, and attachinghardware,
• side airbags (if equipped). Refer to Side airbag system later in thischapter.• one or more impact and safing sensors.• the same indicator light, RCM
Never place your arm over the airbag module as a deployingairbag can result in serious arm fractures or other injuries.Steps you can take to properly
Brake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
of airbag deployment. Thus, it is extremely important that occupants beproperly restrained as far away from the airbag module as possible whilemaintai
When the front passenger seat isoccupied and the sensing systemhas turned off the passenger’sfrontal airbag, the ⬙passenger airbagoff⬙ or ⬙pass airbag
Sitting improperly out of position or with the seat back reclinedtoo far can take off weight from the seat cushion and affect thedecision of the passe
Relationship Center at the phone number shown in the CustomerAssistance section of this Owners Guide.Any alteration/modification to the front passenge
Do not lean your head on the door. The side airbag could injureyou as it deploys from the side of the seatback.Do not attempt to service, repair, or m
not of the type sufficient to cause activation. Side airbags are designedto inflate in side-impact collisions, not roll-over, rear-impact, frontal orn
Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.Alwa
Booster seats should be used until you can answer YES to ALL of thesequestions:• Can the child sit all the way backagainst the vehicle seat back withk
The shoulder belt should cross the chest, resting snugly on the center ofthe shoulder. The lap belt should rest low and snug across the hips,never up
Engine oil pressure: Illuminateswhen the oil pressure falls below thenormal range, refer to Engine oil inthe Maintenance andSpecifications chapter.Tra
When installing a child safety seat:• Review and follow the informationpresented in the AirbagSupplemental Restraint Systemsection in this chapter.• U
Installing child safety seats with combination lap and shoulderbeltsairbags can kill or injure a child in a child seat. NEVER place arear-facing child
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat.
6. Before placing the child into the child seat, forcibly tilt the child seatfrom side to side and in forward direction to make sure that the seat iss
3. Locate the correct anchor for the selected seating position.• Sedan• Wagon4. Open the tether anchor cover.On wagons, snap the tether anchorcover of
5. Clip the tether strap to the anchor as shown.• Sedan• WagonIf the tether strap is clipped incorrectly, the child safety seatmay not be retained pro
Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol.All the LATCH lower anchors areeq
If you install a child seat with rigid LATCH attachments, do not tightenthe tether strap enough to lift the child seat off the vehicle seat cushionwhe
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
• Extra load: A class of P-metric or Metric tires designed to carry aheavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires].Increasing the
Inspecting your tiresPeriodically inspect the tire treads for uneven or excessive wear andremove stones, nails, glass or other objects that may be wed
higher than the manufacturer’s recommended cold inflation pressurewhich can be found on either the tire label or certification label which islocated o
TIRE REPLACEMENT REQUIREMENTSYour vehicle is equipped with tires designed to provide a safe ride andhandling capability.Only use replacement tires and
If you use the temporary spare tire continuously or do not followthese precautions, the tire could fail, causing you to lose controlof the vehicle, po
the road tires and wheels that were originally provided by Ford. If thedissimilar spare tire or wheel is damaged, it should be replaced ratherthan rep
To help prevent the vehicle from moving when you change a tire,be sure the parking brake is set, then block (in both directions)the wheel that is diag
3. If equipped with a wheel coverthat’s bolted on, loosen the fiveplastic nuts with the lug nutwrench.4. Remove the center ornament or wheel cover fro
10. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lug nuttorque specifications later in thischapter for the proper l
Tachometer: Indicates the enginespeed in revolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the
When a wheel is installed, always remove any corrosion, dirt orforeign materials present on the mounting surfaces of the wheelor the surface of the fr
5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new tires to match the new wheeldiameter
numbers represent the week and year the tire was built. For example,the numbers 317 mean the 31st week of 1997. After 2000 the numbersgo to four digit
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
Tire wearMeasure and inspect the tire tread on all your tires periodically.Advanced and unusual tire wear can reduce the ability of tread to gripthe r
Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t
The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear.Tire rotationRotating your tire
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can
tires and chains. If you need to use snow tires and chains, it isrecommended that steel wheels are used of the same size andspecifications as those or
AM/FM STEREO CASSETTE/MACH姞 AUDIO SYSTEM WITH AM/FMSTEREO CASSETTE (IF EQUIPPED)1. Tape: Insert the cassette with theopening to the right. If a tape i
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei
GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).
Maximum Loaded Trailer Weight – is the highest possible weight of afully loaded trailer the vehicle can tow. It assumes a vehicle with onlymandatory o
The following gives you a few examples on how to calculate the availableamount of cargo and luggage load capacity:• Another example for your vehicle w
Towing a trailer places an additional load on your vehicle’s engine,transaxle, brakes, tires and suspension. Inspect these componentscarefully after t
Safety chainsAlways connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cr
Trailer towing tips• Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turni
STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo
6. Balance: Press / to shiftsound to the left/right speakers.7. Fade: Press/ to shiftsound to the rear/front speakers.8. Scan: Press SCAN to hear a br
Extended idling at high engine speeds can produce very hightemperatures in the engine and exhaust system, creating the riskof fire or other damage.Do
2. Make sure the headlamps and electrical accessories are off.• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).• Turn the k
Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced.• If the driver’s safety
Using the engine block heater (if equipped)An engine block heater warms the engine coolant which aids in startingand heater/defroster performance. Use
Refer to Brake system warninglight in the Instrument Clusterchapter for information on the brakesystem warning light.Four-wheel anti-lock brake system
Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake
During Traction Control娂 operation,the traction control active light willilluminate, you may hear an electricmotor type of sound coming fromthe engine
• Some noise is normal during operation. If the noise is excessive, checkfor low power steering pump fluid level before seeking service by yourdealer.
Do not drive your vehicle until you verify that the brakelampsare working.Always set the parking brake fully and make sure the gearshift islatched in
Understanding the gearshift positions of the 4–speed automatictransaxleThis vehicle is equipped with an adaptive Transmission Shift Strategy.Adaptive
16. Tune: Works in radio mode orCD mode. Press/ to changefrequency down/up or previous/nextdisc.17. Cassette door: Insert acassette into the cassette
To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)Always set the parking brake full
If your vehicle gets stuck in mud or snowIf your vehicle gets stuck in mud or snow, it may be rocked out byshifting between forward and reverse gears,
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
If your vehicle is a sedan, the fuelpump shut-off switch is located onthe right side of the trunk behindthe trunk liner.If your vehicle is a wagon, th
FUSESIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check th
To remove a fuse use the fuse puller tool provided on the fuse panelcover.The fuses are coded as follows.Fuse/relaylocationFuse ampratingPassenger com
Fuse/relaylocationFuse ampratingPassenger compartment fusepanel description17 15A Stop lamp, Speed controldeactivation switch18 15A Parklamps, PWM (ba
Fuse/relaylocationFuse ampratingPassenger compartment fusepanel description30 10A Courtesy lighting, Battery saver,Power mirrors, Decklid lamp,Power a
Power distribution boxThe power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protec
AUDIO SYSTEM WITH AM/FM STEREO/SINGLE CD PLAYER(IF EQUIPPED)1. Clock: To set the hour, press andhold the H control. When thedesired hour appears, rele
The high-current fuses are coded as follows.Fuse/relaylocationFuse ampratingPower distribution boxdescription1 60A** Fuse junction panel2 30A** Powert
Fuse/relaylocationFuse ampratingPower distribution boxdescription18 10A* (Vulcanengine only)A/C clutch relay, PCM keep alivepower— (Duratecengine only
JUMP STARTING YOUR VEHICLEThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury
Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable. Make th
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli
6. Scan: Press to hear a briefsampling of all listenable radiostations or CD tracks. Press again tostop.7. CD: Press to play a CD. Pressagain to toggl
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai
Board membershipThe Board consists of:• Three consumer representatives• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa
Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)In those cases where you continue to feel that the efforts by Ford ofCanada and the dealer to
If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips.• Always
Seating and Safety Restraints 86Seating 86Safety restraints 91Airbags 107Child restraints 116Tires, Wheels and Loading 129Tire Information 130Tire Inf
16. EJ (Eject): Press to eject a CD.17. AM/FM: Press to choose afrequency band (AM/FM1/FM2).CD CHANGER (IF EQUIPPED)Your CD changer is either located
• 3.0L Vulcan engine• 3.0L Duratec engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PL
WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub
• If grease or tar is present on the material, spot-clean the area firstwith Motorcraft Spot and Stain Remover (ZC-14).• Never saturate the seat cover
FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury dealer has many quality products availableto clean your vehicle and protect its
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide sc
Working with the engine on1. Set the parking brake and ensure the gearshift is securely latched in P(Park).2. Block the wheels to prevent the vehicle
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.0L V6 Vulcan engine1. Automatic transmission fluid dipstick2. Brake fluid reservoir3. Air filter ass
3.0L DOHC V6 Duratec engine1. Automatic transmission fluid dipstick2. Brake fluid reservoir3. Air filter assembly4. Battery5. Engine oil dipstick6. En
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
Checking and adding washer fluid for the liftgate (Wagon)The opening for the reservoir islocated on the passenger side underthe tail lamp. Refill this
5. Line up the CD with the grooveof the disc holder. Ensure that thelabel on the CD faces downwards.6. Press the disc holder until it lockssecurely in
5. Locate and carefully remove the engine oil indicator (dipstick).• 3.0L Vulcan engine• 3.0L Duratec engine2005 Taurus (tau)Owners Guide (post-2002-f
6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.• If the oil level is between the two holes or between the MIN andMAX mar
3. Recheck the engine oil level. Make sure the oil level is not above theupper hole or MAX mark on the engine oil level indicator (dipstick).4. Instal
It is recommended you use the appropriate Motorcraft oil filter (oranother brand meeting Ford specifications) for your engine application.BATTERYYour
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a
If the battery has been disconnected or a new battery has been installed,the clock and radio settings must be reset once the battery isreconnected.• A
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur
coolant degas system with a pressurized cap, or if it is necessary toremove the coolant pressure relief cap on the radiator of a vehicle withan overfl
Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut
• Tighten very loose tapes by inserting a finger or pencil into the holeand turning the hub.• Remove loose labels before inserting tapes.• Allow tapes
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsDo not overfill the fuel tank. The pressure in an overfilled tankmay cause leak
• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek med
Flexible fuel components and standard unleaded gasoline fuelcomponents are not interchangeable. If your vehicle is notserviced in accordance with flex
Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1/8 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref
contains more metallic additives than regular fuel. We recommend usingregular grade fuel. In Canada, many fuels contain metallic additives, butfuels f
It should not be necessary to add any aftermarket products to your fueltank if you continue to use high quality fuel of the recommended octanerating.
Fuel FilterFor fuel filter replacement, see your dealer or a qualified servicetechnician. Refer to scheduled maintenance information for theappropriat
• Always use fuel with the recommended octane rating.• Use a known quality gasoline, preferably a national brand.• Use the same side of the same pump
• Anticipate stopping; slowing down may eliminate the need to stop.• Sudden or hard accelerations may reduce fuel economy.• Slow down gradually.• Driv
• Driving on flat terrain offers improved fuel economy as compared todriving on hilly terrain.• Transmissions give their best fuel economy when operat
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Passenger air
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
3. The fuel cap may not have been securely tightened. See Fuel fillercap in this chapter.These temporary malfunctions can be corrected by filling the
POWER STEERING FLUID• 3.0L Vulcan engine• 3.0L Duratec engineCheck the power steering fluid. Refer to the scheduled maintenanceinformation for the ser
3.0L V6 Vulcan engine4. Check the fluid level on thedipstick. It should be between thearrows in the FULL HOT range. Donot add fluid if the level is wi
BRAKE FLUIDThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“
7. Remove the dipstick and inspect the fluid level. The fluid should be inthe designated areas for normal operating temperature.Low fluid levelDo not
Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may affect transmissionoperation and re
REFILL CAPACITIESFluid Ford Part Name Application CapacityBrake fluid Motorcraft HighPerformance DOT3 Motor VehicleBrake FluidAll Between MAX andMIN o
2Use of synthetic or synthetic blend motor oil is not mandatory. Engineoil need only meet the requirements of Ford specificationWSS-M2C930-A and the A
ItemsFord Part Nameor equivalentFord PartNumberFordSpecificationEngine coolant MotorcraftPremium GoldEngine Coolant(yellow-colored)VC-7-A (U.S.,except
OPERATING TIPS• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity buildup
ENGINE DATAEngine 3.0L V6 Vulcanengine3.0L FFV V6engine3.0L DOHC V6Duratec engineCubic inches 182 182 181Required fuel 87 octane 87 octane orEthanol (
2005 Taurus (tau)Owners Guide (post-2002-fmt)USA (fus)Maintenance and Specifications241
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea
Transmission/Transaxle code designationsYou can find a transmission/transaxle code on the vehicle certificationlabel. The following table tells you wh
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford
LifestyleBike racksCargo organization and managementSmoker’s packPeace of mindFirst aid and highway safety kitsAirbag anti-theft locksWheel locksVehic
AAccessory delay ...48Air cleaner filter ...236Air conditioning ...25Airbag suppleme
Cleaning your vehicleengine compartment ...199instrument panel ...201interior ...201inte
Engine oil ...209checking and adding ...209dipstick ...209filter, specifica
AUTOMATIC TEMPERATURE CONTROL SYSTEM (IF EQUIPPED)1. OFF: Outside air is shut out andthe climate control system is turnedoff.2. A/C: Press to activate
lighting up panel andinterior ...30JJack ...134positioning ...
Power Windows ...47RRadio ...15, 18Rear window defroster ...28Relays ...
wrecker ...187Traction control ...165Transaxlefluid, refill capacities ...237lubrican
254
255
256
6. AUTO: Press to engage fullautomatic operation, and select thedesired temperature using thetemperature control. The system will automatically determ
OPERATING TIPS• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
REAR WINDOW DEFROSTERThe rear defroster control is locatedon the instrument panel.Press the rear defroster control toclear the rear window of thin ice
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola
Maintenance and Specifications 204Engine compartment 206Engine oil 209Battery 213Engine Coolant 215Fuel information 220Part numbers 236Refill capaciti
High beamsPush the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate.Flash to passPull toward you slightly to acti
AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident the alignment of yo
To see a clearer light pattern foradjusting, you may want to blockthe light from one headlamp whileadjusting the other.5. Locate the vertical adjuster
the lamp will remain on for 25 seconds after the door is shut. If anyother door has been opened from the inside, the lamp will shut offimmediately aft
BULB REPLACEMENTHeadlamp CondensationThe headlamps are vented to equalize pressure. When moist air entersthe headlamp(s) through the vents, there is a
Function Number of bulbs Trade numberRear side markerlamp (wagon)2 194Cargo lamp(wagon)1 578Dome lamp 1 12V6WDome/map lamp 3 578Visor vanity lamp(pass
4. Remove the protective dust shieldfrom the housing by turning thedust shield counterclockwise (whenviewed from the rear).5. Disconnect the electrica
To install the new bulb:Handle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and donot to
Replacing front parking lamp/turn signal/cornering lamp bulbs1. Make sure the headlamp controlis in the OFF position and open thehood.2. Remove the bo
Replacing high-mount brakelamp assembly — Sedan onlyTo change the high-mount brakelamp assembly:1. Pry the light assembly away fromits housing and pus
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
6. Remove four nuts from the lampassembly.7. Carefully lift the lamp assemblyaway from the liftgate.8. Remove the bulb socket byrotating it counterclo
3. On the underside of the spoiler,remove the two decorative screwcovers (on the LED module).4. Remove the two screws that areholding the LED module i
Replacing tail/brake/turn signal/backup lamp bulbsSedanThe tail lamp, brake lamp, turnsignal lamp and backup lamp bulbsare located in the same portion
WagonThe tail lamp/turn lampbulbs/brake/backup are located inthe same portion of the tail lampassembly, one just below the other.Follow the same steps
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
Press the washer control to activatethe rear washer. The wiper willcome on when the washer control ispressed, if it is not already on.Changing the wip
TILT STEERING WHEELTo adjust the steering wheel:1. Pull and hold the steering wheelrelease control toward you.2. Move the steering wheel up ordown unt
Always keep the power point caps closed when not being used.Cigar/Cigarette lighter (if equipped)Do not plug optional electrical accessories into the
Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controlsexcept for the driver’s press
Power side view mirrorsTo adjust your mirrors:1. Select L to adjust the left mirroror R to adjust the right mirror.2. Move the control in the directio
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
3. Press the SET ACC control andrelease it.4. Take your foot off the acceleratorpedal.5. The CRUISE indicator light onthe instrument cluster will turn
Increasing speed while using speed controlThere are three ways to set a higherspeed:• Press and hold the SET ACCcontrol until you get to thedesired sp
Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal. This willnot erase your vehicle’spreviously set s
HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED)The HomeLink威 Wireless Control System, located on the driver’s visor,provides a convenient way to repla
1. Press and hold the two outsidebuttons releasing only when theindicator light begins to flash after20 seconds. Do not repeat Step 1to program additi
Note: There are 30 seconds in which to initiate Step 8.8. Return to the vehicle and firmly press, hold for two seconds andrelease the HomeLink威 button
Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet
MESSAGE CENTERWith the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle informationthrough
The DTE function will display LOW FUEL LEVEL and sound a tone forone second when you have approximately 50 miles (80 km) to empty. Ifyou RESET this wa
Trip elapsed drive timeSelect this function from the INFOmenu to display a timer.To operate the Trip Elapsed DriveTime perform the following:1. Press
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
Most geographic areas (zones) have a magnetic north compass point thatvaries slightly from the northerly direction on maps. This variation is fourdegr
6. Release the RESET control, thenslowly press RESET down again.7. Press the SET control repeatedlyuntil the correct zone setting foryour geographic l
2. Pressing the RESET controlcycles the message center througheach of the language choices.3. Press and hold the RESETcontrol to set the language choi
9. TRACTION CONTROL (if equipped)System warningsSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems.In t
Warnings StatusLow brake fluid Warning returns after the ignition keyis turned from OFF to RUNLiftgate ajar (if equipped)Check Traction Control (ifequ
CHECK CHARGING SYSTEM. Displayed when the electrical system isnot maintaining proper voltage. If you are operating electrical accessorieswhen the engi
• Park brake• Oil pressure sensorContact your dealer as soon as possible if these messages occur on aregular basis.CENTER CONSOLEYour vehicle may be e
Mobile Communication Equipment includes, but is not limited to cellularphones, pagers, portable email devices, in-vehicle communicationssystems, telem
LIFTGATE (WAGON ONLY)You can open and close the liftgate and the liftgate window from outsidethe vehicle. It cannot be opened from inside the cargo ar
To install the shade:1. Fasten the cover into themounting brackets (make sure thecover is right side up).2. Pull the end of the shade towardyou and ho
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental restraint
4. Push in the right end cap(marked RH) about1⁄4of the totallength to disengage the clutch andhold the end cap in while turningthe roller tube toward
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
1. Turn the ignition to the 4 (ON)position, then press the power doorUNLOCK control 3 times.2. Turn the ignition to the 3 (OFF)position, then press th
INTERIOR LUGGAGE COMPARTMENT RELEASEYour vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of esc
REMOTE ENTRY SYSTEM (IF EQUIPPED)This device complies with part 15 of the FCC rules and with RS-210 ofIndustry Canada. Operation is subject to the fol
The inside lights will not turn off if:• they have been turned on using the dimmer control or• any door is open.The battery saver feature will turn of
To replace the battery:1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIR
How to reprogram your remote entry transmittersYou must have all remote entry transmitters (maximum of four)available before beginning this procedure.
The inside lights will not turn off if:• they have been turned on with the dimmer control, or• any door is open.The battery saver will shut off the in
5. Turn the ignition to the 3 (OFF) position to exit the procedure.Note: The horn will chirp once to confirm the procedure is complete.Note: The puddl
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
Erasing personal codes1. Enter the factory set 5–digit code. The keyless entry keypad andinterior lights will illuminate and the driver’s door will un
To deactivate/reactivate the autolock feature using the power doorunlock controlYou must complete Steps 1-4 within 30 seconds or the procedure willhav
objects will not cause damage to the coded key, but may cause amomentary issue if they are too close to the key when starting theengine. If a problem
Replacing coded keys can be very costly. Store an extra programmed keyaway from the vehicle in a safe place to help prevent anyinconveniences. Please
9. Your new unprogrammed key is now programmed.If the key has been successfully programmed it will start the vehicle’sengine and the theft indicator l
Disarming the systemYou can disarm the system by any of the following actions:• Unlock the doors by pressing thecontrol on your remote entrytransmitte
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Using the manual lumbar support (if equipped)The lumbar control is located on thefront of the seat cushion.Turn to adjust lumbar support.Adjusting the
Adjusting the front power seat (if equipped)The control is located on the outboard side of the seat cushion.Press to raise or lower the frontportion o
REAR SEATS2nd seat/split-folding rear seat (if equipped)SedanPull the loop forward to release theseatback and then fold the seatbackdown.WagonLift the
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
To open up the seat:1. Unlock the floor panel with thekey, then use the handle to fold thefloor panel toward the front of thecar.2. Remove the cargo c
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped underneath theseatback. After returning the
The fact that the pretensioners or airbags did not activate for both frontseat occupants in a collision does not mean that something is wrong withthe
Air bags can kill or injure a child in a child seat. NEVER place arear-facing child seat in front of an active air bag. If you mustuse a forward-facin
manner in response to the occupant’s forward momentum. This helpsreduce the risk of force-related injuries to the occupant’s chest bylimiting the load
All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bagsupplemental restraint system (
2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.Energy management retractorsYour vehicle has a seat belt system equipped w
How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt
After any vehicle collision, the seat belt system at all outboardseating positions (except driver, which has no “automatic lockingretractor” feature)
Safety belt usage sensorsThe driver and front outboard passenger safety belt buckles areequipped with sensors that detect if the safety belts are fast
Commentaires sur ces manuels