Ford 2011 Flex v.1 Manuel d'utilisateur

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 16Message center 18Entertainment Systems 28AM/FM stereo with CD/MP3 28Auxiliary

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

The power outlet is not designed for the following electric appliances;they may not work properly:• Cathode ray tube type televisions.• Motor loads, s

WARNING: When closing the power windows, you should verifythey are free of obstructions and ensure that children and/orpets are not in the proximity o

Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controls(except for the driver’s) pres

EXTERIOR MIRRORSPower side view mirrorsWARNING: Do not adjust the mirror while the vehicle is inmotion.To adjust your mirrors:1. Rotate the control cl

WARNING: Never adjust the accelerator and brake pedal withfeet on the pedals while the vehicle is moving.Memory feature (if equipped)The accelerator a

4. Take your foot off the accelerator pedal.5. The indicatorlight on the instrument cluster will turn on.Note:• Vehicle speed may vary momentarily whe

STEERING WHEEL CONTROLS (IF EQUIPPED)Radio control featuresVOL + (Volume): Press to increasethe volume.VOL – (Volume): Press to decreasethe volume.(Se

For further information on the SYNC威 system, refer to the SYNC威supplement.Navigation system/SYNC威hands-free control features (ifequipped)Presscontrol

To close the multi-panel Vista Roof™: Pull and release the SLIDEcontrol, the roof will close automatically. Press the switch again to stopthe roof.Bou

Do not use the HomeLink威 Wireless Control System with any garagedoor opener that lacks safety stop and reverse features as required byU.S. federal saf

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

• If the indicator light stays on constantly, programming is completeand your device should activate when the HomeLink威 button is pressedand released.

• Continue to press and hold the HomeLink威 button (note Step 2 in theProgramming section) while you press and release — every twoseconds (“cycle”) you

2. The indicator light will begin to flash after 20 seconds. Withoutreleasing the HomeLink威 button, follow Step 1 in the Programmingsection.For questi

• Do not leave the liftgate open while driving. Doing so could causeserious damage to the liftgate and its components as well as allowingcarbon monoxi

If the liftgate reverses and starts to close after a open request, a fastcontinuous chime indicates excessive load on the gate or a possible strutfail

To power open or close theliftgate with the integratedkeyhead transmitter:Presstwice within threeseconds to power open or close theliftgate. Refer to

Note: The liftgate movement direction can be reversed with a secondpress of the instrument panel, or the rear cargo area control buttons, ora second d

CARGO AREA FEATURESCargo net (if equipped)The cargo pouch net secureslightweight objects in the cargoarea. Attach the net to the anchorsprovided. Do n

KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the lo

MYKEY™The MyKey™ feature allows you to program a restricted driving mode topromote good driving habits. All but one of the keys programmed to thevehic

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A wa

2. Press and release the RESET button. HOLD RESET TO CONFIRMMYKEY will be displayed.3. Press and hold the RESET button for two seconds until MARK THIS

2. Press SETUP until PRESS RESET TO CLEAR MYKEY is displayed.3. Press and release the RESET button. HOLD RESET TO CONFIRMCLEAR is displayed.4. Press a

Note: For all vehicles, the number of MYKEY(S) PROGRAMMED orADMIN KEYS PROGRAMMED that is displayed in the MyKey™ systemstatus menus will include the

Condition Potential CausesCannot clear MyKey™ • Key in the ignition is a MyKey™• No MyKeys™ are programmed tothe vehicle. Refer to Create aMyKey™ sect

POWER DOOR LOCKS• Press the control to unlock alldoors.• Press thecontrol to lock alldoors.Smart locksThis feature helps to prevent you from locking y

Deactivating/activating autolock featureYour vehicle comes with the autolock features activated; there are fourmethods to enable/disable this feature:

Keyless entry keypad autolock enable/disable procedure1. Turn the ignition to the offposition.2. Close all the doors.3. Enter factory–set 5–digit entr

Note: The autounlock feature can be activated/deactivatedindependently of the autolock feature.Power door lock switch autounlock enable/disable proced

Keyless entry keypad autounlock enable/disable procedure1. Turn the ignition to the offposition.2. Close all the doors.3. Enter factory–set 5–digit en

REMOTE ENTRY SYSTEMThe integrated keyhead transmitter (IKT) complies with part 15 of theFCC rules and with RSS-210 of Industry Canada. Operation is su

WARNING: Under engine misfire conditions, excessive exhausttemperatures could damage the catalytic converter, the fuelsystem, interior floor coverings

• Vehicles not equipped with apower liftgateThe typical operating range for your IKT is approximately 33 feet(10 meters). A decrease in operating rang

2. Press and release again within three seconds to unlock all thedoors.The remote entry system activates the illuminated entry feature; thisfeature tu

WARNING: Make sure all persons are clear of the liftgate areabefore using power liftgate control.In order to fully lower and latch the liftgate, press

Deprogramming memory feature from the transmitterTo deactivate this feature:1. Press and hold either the 1 or 2 button on the driver’s door for fivese

Replacing lost integrated keyhead transmitters (IKTs)If you would like to have your integrated keyhead transmittersreprogrammed because you lost one,

• If the courtesy lamps were turned on because one of the vehicle doorsor the liftgate was opened, the battery saver will shut off them off10 minutes

Note: Touching 5 • 6, 7 • 8, or 9 • 0 keypad numbers as a sixth digitwill not recall a driver memory setting.Note: The factory-set code cannot be asso

To unlock all doors, enter the factory set code or your personal code,then touch the 3 • 4 control within five seconds.To lock all doors, press and ho

Anti-theft indicatorThe anti-theft indicator is located in the instrument panel cluster.• When the ignition is in the offposition, the indicator will

keyless entry transmitter. A maximum of eight coded keys can beprogrammed to your vehicle; only four of these eight keys can be IKTswith remote entry

Airbag readiness: If this light failsto illuminate when the ignition isturned to on, continues to flash orremains on, have the systemserviced immediat

4. After three seconds but within 10 seconds of turning the ignition tothe 1 (off) position, insert the second previously coded key into theignition.5

The system is ready to arm whenever the key is in the off position, or isremoved from the ignition. Either of the following actions will pre-armthe al

Disarming the systemYou can disarm the system by any of the following actions:• Unlock the doors by using the remote entry transmitter portion ofyour

FRONT SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the e

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Tilting head restraints (if equipped)T

Pull lever up to adjust seatback.WARNING: Beforereturning the seatback to itsoriginal position, make sure thatcargo or any objects are nottrapped behi

WARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event of a col

Move the control in the directionsshown to move the seat forward orbackward.Press the control to recline theseatback forward or rearward.Using the pow

AdvanceTrac威/traction controloff: Illuminates when theAdvanceTrac威/traction control hasbeen turned off. Refer to theDriving chapter for moreinformatio

Heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cordinjur

A position can only be recalled when the transmission gearshift is in Park(automatic transmission). A memory seat position may be programmedat any tim

Easy entry/exit feature (if equipped)This feature automatically moves the driver’s seat rearward 2 in (5 cm)when:• the transmission is in N (Neutral)

WARNING: The adjustable head restraint is a safety device.Whenever possible it should be installed and properly adjustedwhen the seat is occupied.To r

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting second row bucket and bench

Note: You may have to move the front row seat forward to allow the 2ndrow seat to be fully tumbled. Stow the head restraint by pressing thehead restra

3. To return the seatback to thefloor from tumbled position, rotatethe seat down until you hear itlatching to the floor.4. To return the seatback to t

2nd row PowerFold姞 and tumble seatWARNING: Ensure that the seat is unoccupied when folding itdown. Folding the seat while occupied could result in occ

4. To return the seatback to theupright position• Lift the seatback toward the rearof the vehicle, and• Rotate the seatback until youhear a click, loc

WARNING: Do not adjust or release the seat floor latch whilevehicle is in motion. Do not operate the vehicle with seats intumbled position. Always lat

Turn signal: Illuminates when theleft or right turn signal or thehazard lights are turned on. If theindicators flash faster, check for a burned out bu

Stowing the third row seat1. Remove all objects from the seatand stowage tub.2. Stow the head restraints bypressing the head restraint releasebutton w

Note: Do not use the third rowseatback as a load floor when theseatback is folded.Note: In order to allow the seat to latch in the stowed position, do

2. To return the seatback to uprightposition, pull the number 1 strap,then while holding the number 1strap, pull the long strap located onthe seatback

3. From the rear of the vehicle,tumble the seat by pulling thenumber 2 strap while pulling on thestrap located on the top of theseatback.WARNING: Do n

Press the seat selection button (4) to select either right-hand seat, theleft-hand seat or both. First select the seat you would like to adjust, thens

WARNING: Do not drivethe vehicle when the thirdrow seat is rotated backwards.During a sudden stop, the safetybelts are not functional in thisposition,

How does the Personal Safety System™ work?The Personal Safety System can adapt the deployment strategy of yourvehicle’s safety devices according to cr

Front passenger sensing systemFor airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occu

Front safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly ag

Safety belt precautionsWARNING: Always drive and ride with your seatback uprightand the lap belt snug and low across the hips.WARNING: To reduce the r

Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,

WARNING: Front and rear seat occupants, including pregnantwomen, should wear safety belts for optimum protection in anaccident.Combination lap and sho

Pregnant women should alwayswear their safety belt. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips

How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt

WARNING: BELT AND RETRACTOR ASSEMBLY MUST BEREPLACED if the safety belt assembly “automatic lockingretractor” feature or any other safety belt functio

WARNING: Do not use extensions to change the fit of theshoulder belt across the torso.Front safety belt height adjustmentYour vehicle has safety belt

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignition switchis turned to the on position...The safety belt wa

If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the onposition or less than1-2 minutes h

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra

Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate

The driver and front passenger Belt-Minder威 features can bedeactivated/activated by performing the following procedure:Before following the procedure,

Tachometer: Indicates the enginespeed in revolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The airbag supplemental restraint system (SRS) is designed to work inconjunction with the safety belts to he

WARNING: Do not place any object between an occupant andan airbag or near any other airbag covering. The airbag may notinflate properly and might forc

WARNING: Modifying or adding equipment to the front end ofthe vehicle (including frame, bumper, front end body structureand tow hooks) may affect the

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

• diagnostic module.• the electrical wiring which connects the components.• Front passenger sensing system. Refer to Front passenger sensingsystem lat

The front passenger sensing systemuses a ⬙passenger airbag off⬙ or⬙pass airbag off⬙ indicator which willilluminate and stay lit to remind youthat the

OccupantPass Airbag OffIndicator LightPassenger AirbagEmpty seat Unlit DisabledSmall child in childsafety seat or boosterLit DisabledSmall child with

ObjectsPass Airbag OffIndicator LightPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi

A difficulty with the system is indicated by one or more of the following:• The readiness light (same lightfor front and side airbag system)will eithe

Remember to turn the ignition off when refueling to allow this feature tocorrectly detect the added fuel.LOW FUEL LEVEL will display when you have app

How does the side airbag system work?The design and development of the side airbag system includedrecommended testing procedures that were developed b

WARNING: Several air bag system components get hot afterinflation. Do not touch them after inflation.WARNING: If the sideairbag has deployed, theairba

WARNING: All occupants of the vehicle including the drivershould always wear their safety belts even when an airbag SRSand Safety Canopy威 System is pr

The Safety Canopy System, in combination with safety belts, can helpreduce the risk of severe injuries in the event of a significant side impactcollis

Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref

SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfantsortoddlersChildren weighing 40 lb

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle.If the child is the proper height, age, and weigh

Locks and Security 118Keys 118Locks 124Anti-theft system 137Seating and Safety Restraints 143Seating 143Safety restraints 165Airbags 180Child restrain

TIMERTimer displays the trip elapsed drive time.To operate, do the following:1. Press and release RESET in order to start the timer.2. Press and relea

position whenever possible. If all children cannot be seated andrestrained properly in a rear seating position, properly restrain thelargest child in

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out.6. All

10. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the

Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol.The LATCH anchors are locat

WARNING: Depending on where you secure a child restraint,and depending on the child restraint design, you may blockaccess to certain safety belt buckl

Attaching child safety seats with tether strapsMany forward-facing child safety seats include a tether strap whichextends from the back of the child s

Perform the following steps to attach a child safety seat to the tetheranchor:1. Route the child safety seat tetherstrap over the back of the seat.Lif

• 2nd row bench (60/40)• 3rd rowNote: The cargo tie-downs at therear edge of the floor are nottether anchors.3. Clip the tether strap to theanchor as

Child booster seatsThe belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child

OIL LIFEThis displays the remaining oil life.An oil change is required whenever indicated by the message center andaccording to the recommended mainte

Booster seats should be used until you can answer YES to ALL of thesequestions when seated without a booster seat:• Can the child sit all the way back

• High back booster seatsIf, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo

If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat may improve thisconditio

WARNING: Failure to inspect and if necessary replace thesafety belt assembly or child restraint system under the aboveconditions could result in sever

NOTICE TO CROSSOVER VEHICLE OWNERSCrossover vehicles handle differentlythan passenger cars in the variousdriving conditions that areencountered on str

driving surfaces are relatively level, obstruction-free and otherwisesimilar to normal on-road driving conditions. Operating your vehicleunder other t

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli

WARNING: The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydro

Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr

WARNING: Under-inflation is the most common cause of tirefailures and may result in severe tire cracking, tread separationor “blowout”, with unexpecte

EASY ENTRYThis feature automatically moves the driver’s seat backwards for easyexit/entry from the vehicle.Press RESET to turn it off or on.REAR PARK

Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w

• Do not run over curbs or hit the tire against a curb when parkingWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the

• Front-wheel drive (FWD) vehicles(front tires at top of diagram)• Rear-wheel drive (RWD)vehicles/Four-wheel drive(4WD)/All-wheel drive (AWD)vehicles

Sometimes irregular tire wear can be corrected by rotating the tires.Note: If your tires show uneven wear ask an authorized dealer to checkfor and cor

3. 65: Indicates the aspect ratio which gives the tire’s ratio of height towidth.4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or ri

8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n

13. Maximum Permissible Inflation Pressure: Indicates the tiremanufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load

Types of messages and warnings:• Some messages will appear briefly to inform you of something youmay need to take action on or be informed of.• Some m

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Understanding your tire pressure monitoring system (TPMS)The tire pressure monitoring system measures pressure in your four roadtires and sends the ti

When you believe your system is not operating properlyThe main function of the tire pressure monitoring system is to warn youwhen your tires need air.

Low tire pressurewarning lightPossible cause Customer action requiredFlashing warninglightSpare tire in use Your temporary spare tire is inuse. Repair

SNOW TIRES AND CABLES/CHAINSWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire o

VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is lowand the brake system should be inspected immediately. Refer to Brakefluid in the Mainten

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle.3. Subtract the combined weight of the driver and pas

1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now youhave the load capacity to transport the cement and your friend home.In metric units,

Powertrain Maximum GCWR - lb(kg)Maximum TrailerWeight - lb (kg)3.5L FWD Class I 6900 (3131) 2000 (907)3.5L AWD Class I 7050 (3199) 2000 (907)EcoBoost™

Weight-distributing hitchWhen hooking-up a trailer using a weight-distributing hitch, always usethe following procedure:1. Park the vehicle (without t

WARNING: Do not connect a trailer’s hydraulic brake systemdirectly to your vehicle’s brake system. Your vehicle may nothave enough braking power and y

Driving while you towWhen towing a trailer:• Turn off the speed control. The speed control may shut offautomatically when you are towing on long, stee

RECREATIONAL TOWINGFollow these guidelines for your specific powertrain combination to towyour vehicle for personal travel (such as behind a motor hom

TRAILER SWAY REDUCE SPEED (if equipped) — Displayed whenthe trailer sway control has detected trailer sway. For more information,refer to the Driving

STARTINGPositions of the ignition1. Off— locks the automatictransmission gearshift lever andallows key removal. This positionalso shuts the engine and

WARNING: Do not start your vehicle in a closed garage or inother enclosed areas. Exhaust fumes can be toxic. Always openthe garage door before you sta

• Make sure the gearshift lever is inP (Park).3. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminat

that assists in starting the engine. After releasing the key from the 4(start) position, the engine may continue cranking for up to 10 secondsor until

WARNING: To reduce the risk of electrical shock, do not useyour heater with ungrounded electrical systems or two-pronged(cheater) adapters.Prior to us

How to use the engine block heaterEnsure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth.Depending on the type

Brake assistThe brake assist system provides full braking force during panic brakingsituations. It detects a rapid application of the brake pedal and

WARNING: Always set the parking brake fully and make surethat the gearshift is securely latched in P (Park).The parking brake is not recommended to st

WARNING: Vehicle modifications involving braking system,aftermarket roof racks, suspension, steering system, tireconstruction and/or wheel/tire size m

The AdvanceTrac威 with RSC威system includes an AdvanceTrac威button located on the center of theinstrument panel.The stability control light and the stabi

BACK UP SLOWLY USE CAUTION (if equipped) — May displaywhen using the active park assist system. See Active park assist in theDriving chapter for more

If the TCS is activated excessively in a short period of time, the brakingportion of the system may become temporarily disabled to allow thebrakes to

Certain adverse driving maneuvers may activate the RSC威 system, whichinclude:• Emergency lane-change• Taking a turn too fast• Quick maneuvering to avo

AdvanceTrac威 FeaturesControlswitchfunctionsModeStabilitycontrolofflightMessagecenter dis-playESC/RSCTCSDefault atstart-upSystem Ini-tializationTurns o

During trailer sway control events, the stability control light in theinstrument cluster will flash momentarily. The cluster message centerwill also d

WARNING: The EPS system has diagnostics checks thatcontinuously monitor the EPS system to ensure proper operationof the electronic system. When an ele

If the steering wanders or pulls equipped with either EPS or hydraulicsteering system, check for:• an improperly inflated tire• uneven tire wear• loos

4. Locate the brake shift interlocklever on the passenger side of theshifter assembly.5. Apply the brake pedal. Using ascrewdriver (or similar tool),

Understanding the gearshift positions of the 6–speed automatictransmission with transmission control switch (if equipped)Your vehicle has been designe

The automatic transmission shift strategy has the ability to detect hillyterrain or mountainous areas and will provide a limited amount of gradeassist

• Will downshift to the lowest available gear for the current vehiclespeed; allows for first gear when vehicle reaches slower speeds.Understanding the

TOP SPEED MYKEY SETTING — Displayed when a MyKey is in useand the MyKey speed limit is on and the vehicle speed is 80 mph(130 km/h). Refer to MyKey in

D (Drive)The normal driving position for the best fuel economy. Transmissionoperates in gears one through six.M (Manual) SelectShift Automatic™ Transm

Understanding your SelectShift Automatic™ Transmission (SST)(if equipped)This vehicle may be equipped with aSelectShift Automatic™transmission (SST) g

Recommended shift speedsUpshift according to the following chart:Upshifts when accelerating (recommended for best fueleconomy)Shift from:1 - 2 15 mph

WARNING: This system is not designed to prevent contact withsmall or moving objects. The system is designed to provide awarning to assist the driver i

Keep the RSS sensors (located on the rear bumper/fascia) freefrom snow, ice and large accumulations of dirt (do not clean thesensors with sharp object

• (1) Rear bumper• (2) Red zone• (3) Yellow zone• (4) Green zone• (5) Center line of vehicleAlways use caution while backing.Objects in the red zone a

WARNING: Objects that are close to either corner of thebumper or under the bumper, might not be seen on the screendue to the limited coverage of the c

Conditions in which the system may not work:• Something passes between the front bumper and the space such as apedestrian or cyclist• The edge of the

Automatic steering into parking spaceAutomatic steering is activated when you stop the vehicle, remove yourhands from the steering wheel and select th

APA finishedWhen active park assist has completed the automated steering, themessage center displays ACTIVE PARK FINISHED followed by a chime.The driv

AUDIO SYSTEMSAM/FM CD/MP3 satellite compatible sound systemWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury

TroubleshootingWhy isn’t APA searching for a parking space?• You may have deactivated the AdvanceTrac威 system.• One of the doors (except the driver’s

• One of the parked vehicles has a high altitude attachment (i.e. saltsprayer, snow plow, moving truck high bed, etc.) High altitudeattachments may no

Note: The AWD OFF message may also be displayed in the messagecenter if the AWD system has overheated and defaulted to front-wheeldrive. This conditio

sudden return to the pavement which could cause the vehicle to slidesideways out of control or rollover. Remember, your safety and thesafety of others

• In the event of an emergency stop, avoid skidding the tires and do notattempt any sharp steering wheel movements.• If the vehicle goes from one type

If the engine, transmission, AWD system components or axles aresubmerged in water, their fluids should be checked and changed, ifnecessary.Driving thr

Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;

Maintenance and modificationsThe suspension and steering systems on your vehicle have been designedand tested to provide predictable performance wheth

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

Canadian customers refer to your Warranty Guide or visit ourwebsite at www.ford.ca for information on:Using roadside assistanceComplete the roadside a

Setting the clockTo set the time, press CLOCK. Thedisplay will read SET TIME. Use thememory preset numbers (0–9) toenter in the desired time–hours and

Should your vehicle shut off after a collision due to this feature, you mayrestart your vehicle by doing the following:1. Turn the ignition switch to

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

Passenger compartment fuse panelThe fuse panel is located under the instrument panel to the left of thesteering wheel.The fuses are coded as follows.F

Fuse/RelayLocationFuse AmpRatingProtected Circuits9 15A Interior lights, Cargo lamps10 15A Backlighting, Puddle lamps11 10A All wheel drive (AWD)12 7.

Fuse/RelayLocationFuse AmpRatingProtected Circuits32 10A Restraint control module33 10A TT battery charge relay coil34 5A Roll stability control, Refr

WARNING: Always disconnect the battery before servicing highcurrent fuses.WARNING: To reduce risk of electrical shock, always replacethe cover to the

Fuse/RelayLocationFuse AmpRatingProtected Circuits7 30A* Amplifier8 — Not used9 40A* Anti-lock brake system (ABS)pump10 30A* Starter relay11 30A* Powe

Fuse/RelayLocationFuse AmpRatingProtected Circuits33 30A* 3rd row power seats34 30A* Power liftgate35 40A* Front A/C blower36 10A** Backup lamps37 10A

Fuse/RelayLocationFuse AmpRatingProtected Circuits64 HC micro relay PCM65 G8VA relay A/C clutch66 G8VA relay Fuel pump* Cartridge Fuses ** Mini FusesC

If you have a dissimilar spare tire/wheel, then it is intended fortemporary use only. This means that if you need to use it, you shouldreplace it as s

Customer Assistance 320Reporting safety defects (U.S. only) 326Reporting safety defects (Canada only) 326Cleaning 327Maintenance and Specifications 33

MEMORY PRESETS (0–9): Whentuned to any station, press and holda preset button until sound returnsand PRESET # SAVED appears in the display. You can sa

• Use commercial car washing equipment• Use snow chains on the end of the vehicle with the dissimilar sparetire/wheelThe usage of a full-size dissimil

1. Remove the carpeted floor panellocated in the rear of the vehicle,remove the wing nut that securesthe spare tire by turning itcounterclockwise.2. L

1. Block the diagonally oppositewheel.2. Remove wheel cover (ifequipped) with the lug wrench tipand loosen each wheel lug nutone-half turn countercloc

7. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torquespecifications later in this chapterfor the proper lu

4. Insert the straight end of the jackretention bracket through the eyeletof the angled bracket and swing theretention bracket over the jack. Withthe

TEMPORARY MOBILITY KIT (IF EQUIPPED)Your vehicle may be equipped with atemporary mobility kit (locatedunder the driver’s seat). To removethe temporary

1. Air compressor (inside)2. Diverter knob3. On/Off button4. Air pressure gauge5. Deflation button6. Sealant bottle/canister7. Sealant filling clear t

• Read the information in the Tips for use of the temporary mobilitykit section to ensure safe operation of the temporary mobility kit andyour vehicle

• Operating the temporary mobility kit could cause an electricaldisturbance in radio and DVD player operation.What to do when a tire is puncturedA tir

4. Plug the power cable into the 12Vpower point in the vehicle.5. Remove the warning sticker found on the canister and place it on thetop of the instr

CD/MP3 PlayerCD: Press to enter CD/MP3 mode. Ifa disc is already loaded into thesystem, CD/MP3 play will beginwhere it ended last. If no CD is loaded,

Note: When the sealing compound is first added into the tire, theair pressure gauge reading on the compressor unit may indicate ahigher value; this is

3. Turn the dial clockwise to the air position. Turn on the kit by pressingthe on/off button.4. Adjust the tire to therecommended inflation pressurefr

Removal of the sealant canister from the temporary mobility kit1. Unwrap the clear tube from thecompressor housing.2. Press the button located on thet

2. Once aligned, seat the sealantcanister by lightly pushing downuntil you hear an audible click.3. Wrap the clear tube around thecompressor housing.N

Bolt size Wheel lug nut torque*ft-lb N•m1/2-20 UNF 100 135* Torque specifications are for nut and bolt threads free of dirt andrust. Use only Ford rec

WARNING: Do not insert the nozzle of portable fuel containersor aftermarket funnels into the Easy Fuel™ system. This coulddamage the fuel system and i

Connecting the jumper cablesNote: In the illustration, the vehicle on the bottom is used to designatethe assisting (boosting) battery.1. Connect the p

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.Note: In the illustration, the vehicle on the bottom i

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

If the vehicle is towed by other means or incorrectly, vehicledamage may occur.Ford Motor Company produces a towing manual for all authorized towtruck

SEEK: Press SEEK toaccess the previous/next track.CAT (Category) / FOLD(Folder):In MP3 mode only– PressCAT/FOLD and thenpressSEEK to access the previo

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

procedure outlined on the first page of the Customer Assistance section,you may be eligible to participate in the BBB AUTO LINE program.The BBB AUTO L

The CAMVAP program is a straight forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have

If your vehicle must be serviced while you are traveling or living inPuerto Rico, contact the nearest authorized dealer. If the authorizeddealer canno

(Items in this catalog may be purchased by credit card, check ormoney order.)Obtaining a French Owner’s GuideFrench Owner’s Guides can be obtained fro

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

WAXING• Wash the vehicle first.• Use a quality wax that does not contain abrasives.• Do not allow paint sealant to come in contact with any non-body(l

• Do not spray a hot engine with cold water to avoid cracking theengine block or other engine components.• Spray Motorcraft威 Engine Shampoo and Degrea

Satellite Radio (if equipped)Satellite radio is available only with a valid SIRIUS威 radiosubscription. Check with your authorized dealer for availabil

3.5L V6 EcoBoost™ enginePLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your a

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft威 Premium Windshield Washer Concentrate (ZC-32-A) inthe U.S., or Premiu

WARNING: Do not use chemical solvents or strong detergentswhen cleaning the steering wheel or instrument panel to avoidcontamination of the airbag sys

WARNING: On vehicles equipped with seat-mounted airbags, donot use chemical solvents or strong detergents. Such productscould contaminate the side-air

• Test any cleaner or stain remover on an inconspicuous part of theleather as cleaners may darken the leather.• Do not spill coffee, ketchup, mustard,

FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column.2. Go to th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.5L V6 engine1. Power steering fluid reservoir2. Engine coolant reservoir3. Brake fluid reservoir4. B

3.5L V6 EcoBoost™ engine1. Engine coolant reservoir2. Brake fluid reservoir3. Battery4. Power distribution box5. Air filter assembly6. Automatic trans

TEXT: Press and release to displaythe artist and song title. While inTEXT MODE, press again to scrollthrough the Artist (AR), Song (SO), Channel (CH)

Engine shieldSome vehicles may be equippedwith an aero-shield under theengine. This shield needs to beremoved for service, including oiland filter cha

CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Press the locktab to release the bl

3. The wiper arm has a snapretention feature to receive a crosspin from the wiper blade structure.Grip tightly and press on thearm/blade joint from be

• If the oil level is within thisrange, the oil level is acceptable.DO NOT ADD OIL.• If the oil level is below thismark, engine oil must be addedto ra

Engine oil and filter recommendations3.5L V6 engineLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils certified for gasoline e

3.5L V6 EcoBoost™ engineLook for this certificationtrademark.Use SAE 5W-30 engine oilOnly use oils “Certified For Gasoline Engines” by the AmericanPet

BATTERYYour vehicle is equipped with aMotorcraft威 maintenance-freebattery which normally does notrequire additional water during itslife of service.If

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the FULL COLD level, or within theCOLD

titles, the display will read REPLACE SONG? Press OK to access thesaved titles and pressSEEK to cycle through the saved titles.When the song title app

• DO NOT MIX different colors or types of coolant in your vehicle.Make sure the correct coolant is used. DO NOT MIX recycled coolantand new (unused) c

3. Step back while the pressure releases.4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and re

Severe climatesIf you drive in extremely cold climates (less than –34°F [–36°C]):• It may be necessary to increase the coolant concentrationabove 50%.

You may notice a reduction in the vehicle’s speed caused by reducedengine power. Your vehicle has been designed to enter this mode ifcertain high temp

What you should know about fail-safe coolingIf the engine coolant supply is depleted, this feature allows the vehicle tobe driven temporarily before i

WARNING: Fail-safe mode is for use during emergencies only.Operate the vehicle in fail-safe mode only as long as necessary tobring the vehicle to rest

Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforerefueling your vehicle.• Al

RefuelingWARNING: Fuel vapor burns violently and a fuel fire can causesevere injuries. To help avoid injuries to you and others:• Read and follow all

4. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about five seconds after pumping fuel before removing thefuel filler noz

Choosing the right fuelUse only UNLEADED fuel or UNLEADED fuel blended with a maximumof 10% ethanol. Do not use fuel ethanol (E85), diesel, methanol,

b. CHANGE PIN: Press OK when CHANGE PIN is displayed. Thedisplay will read ENTER OLD PIN. Enter your current (old) PINnumber and when the system accep

tank if you continue to use high quality fuel of the recommended octanerating. These products have not been approved for your engine andcould cause da

WARNING: Do not try to pry open or push open the EasyFuel™ system with foreign objects. This could damage the fuelsystem and its seal and cause injury

ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform

2. Each time you fill the tank, record the amount of fuel added (ingallons or liters).3. After at least three to five tank fill-ups, fill the fuel tan

• Warming up a vehicle on cold mornings is not required and mayreduce fuel economy.• Resting your foot on the brake pedal while driving may reduce fue

EMISSION CONTROL SYSTEMYour vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to co

Do not make any unauthorized changes to your vehicle or engine. Bylaw, vehicle owners and anyone who manufactures, repairs, services,sells, leases, tr

Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect

POWER STEERING FLUID (EXCEPT ECOBOOST™ ENGINE)Refer to scheduled maintenance information.1. Start the engine and let it rununtil it reaches normal ope

TRANSMISSION FLUIDChecking automatic transmission fluidRefer to your scheduled maintenance information for scheduledintervals for fluid checks and cha

Extra FeaturesAUX: Press repeatedly to cyclethrough LINE (auxiliary audiomode), SYNC威 (if equipped) andFES modes (if equipped).For location and furthe

B. Clean the area around the clampthat connects the air filter assemblyto the rubber hose (1).C. Remove the bolt cover (ifequipped).D. Remove two bolt

H. Rotate the air filter assembly 90degrees counterclockwise andreinstall into the rubber hose.I. Tighten the clamp (1).J. The transmission fluid leve

The transmission fluid level shouldbe targeted within the cross-hatcharea if at normal operatingtemperature 180°F-200°F(82°C-93°C).High fluid levelIf

For vehicles equipped with the EcoBoost engine, reinstall the airfilter assembly.After the fluid level has been checked and adjusted as necessary, do

Changing the air filter element3.5L V6 engine3.5L V6 EcoBoost engine1. Release the clamps that secure the air filter housing cover.2. Carefully separa

6. Replace the air filter housingcover and secure the clamps. Besure that the air cleaner cover tabsare engaged into the slots of the aircleaner housi

• Cover interior trim to prevent fading.• Keep all rubber parts free from oil and solvents.Engine• The engine oil and filter should be changed prior t

Miscellaneous• Make sure all linkages, cables, levers and pins under vehicle arecovered with grease to prevent rust.• Move vehicles at least 25 feet (

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItems CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationBrake fluidBetween MAX a

Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine oil(3.5L V6 engine)5.5 quarts (5.2L)•Motorcraft威 SAE 5W-20Premium

The auxiliary input jack provides away to connect your portable musicplayer to the in-vehicle audiosystem. This allows the audio from aportable music

Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine coolant(with rear heater)13.2 quarts(12.5L)(3.5L engine)6•Motorcra

ENGINE DATAEngine 3.5L V6 engine3.5L V6 EcoBoost™engineCubic inches 214 214FuelSee Octanerecommendationsearlier in this chapter.See Octanerecommendati

3.5L V6 EcoBoost engineIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requ

Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX

TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C

•Trailer hitches, wiring harnessesand accessories•Cargo organization andmanagementPeace of mind•Remote start •Vehicle tracking and recovery*•Back up c

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP.

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan3892011 Flex (471)Owners Guide, 1st PrintingUSA (fus)

Troubleshooting:1. Do not connect the audio input jack to a line level output. Line leveloutputs are intended for connection to a home stereo and are

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is

GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?This guide describes the scheduled maintenance required for yourvehicle. Carefully following

Your vehicle is very sophisticated and built with multiple complexperformance systems. Every manufacturer develops these systems usingdifferent specif

Get the most from your service and maintenance visitsThere are a lot of reasons why visiting your Ford or Lincoln Mercurydealership for all your servi

Multi-point inspectionIn order to keep your vehicle running right, it is important to have thesystems on your vehicle checked regularly. This can help

Be sure to ask your Ford or Lincoln Mercury dealership service advisoror technician about the multi-point vehicle inspection. It’s acomprehensive way

Scheduled Maintenance Guide3962011 Flex (471)Owners Guide, 1st PrintingUSA (fus)

NORMAL SCHEDULED MAINTENANCE AND LOGFor your convenience, your vehicle is equipped with a message centerwhich determines the proper oil change service

Oil Change Service Interval* 1 2 3 45678910Change engine oil and filter • •••••••••Rotate tires, inspect tire wear and measure treaddepth• •••••••••In

Oil Change Service Interval* 11 12 13 14 15Change engine oil and filter •••••Rotate tires, inspect tire wear and measure tread depth •••••Inspect whee

CONGRATULATIONSCongratulations on acquiring your new Ford Motor Company product.Please take the time to get well acquainted with your vehicle by readi

Your vehicle may be equipped with aUSB port inside your center console.This feature allows you to plug inmedia playing devices, memorysticks, and also

Perform the services noted in the following table at the specifiedtime/mileage (km) period either within 3,000 miles (5,000 km) of theOIL CHANGE REQUI

Maintenance schedule logDEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATIO

DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOUR

DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOUR

SPECIAL OPERATING CONDITIONSIf you operate your Ford/Lincoln/Mercury vehicle primarily in one of themore demanding Special Operating Conditions listed

Extensive idling and/or low-speed driving for long distances as in heavycommercial use such as delivery, taxi, patrol car or liveryAs required – Chang

Operating in dusty conditions such as unpaved or dusty roadsInspect frequently, service asrequired– Replace cabin air filter (if equipped).– Replace e

Special operating condition logDEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VA

DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOUR

EXCEPTIONSIn addition, there are several exceptions to the Normal Schedule. Theyare listed below:Normal vehicle axle maintenance❑Rear axles and power

• Wipe discs from the center out.Don’t:• Expose discs to direct sunlight or heat sources for extended periodsof time.• Clean using a circular motion.C

COOLANT CHANGE RECORDEngine coolant❑6 years or 100,000 miles (160,000 km) - change coolant (whichever comes first).❑After initial change - change cool

Engine coolant change logDEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATI

AAccessory delay ...102Active Park Assist ...276AdvanceTrac ...257Air cleaner filter

in rear seat ...199LATCH ...203recommendations ...197tether anchorage har

cleaning ...328coolant ...348fail-safe cooling ...354idle speed

Illuminated visor mirror ...93Infant seats(see Safety seats) ...199Inspection/maintenance (I/M)testing ...

PParental MyKeyprogramming ...119Park Assist ...276Parking brake ...25

Scheduled Maintenance GuideNormal ScheduledMaintenance and Log ...397What Maintenance ScheduleShould You Follow? ...393Seats ..

fluid, checking and adding(automatic) ...369Turn signal ...85UUniversal garage door opener ..

MP3 track and folder structureYour MP3 system recognizes MP3 individual tracks and folder structureas follows:• There are two different modes for MP3

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m

Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The

FAMILY ENTERTAINMENT DVD SYSTEM (IF EQUIPPED)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongl

Note: The system goes into dual play mode when it is turned on. Audiofrom the DVD system will not play over the rear two speakers until dualplay mode

1. On the front of each monitor,located behind the left trim coverpanel, is the headphone input jack(5). This headphone will listen tothe media select

Protecting the environmentWe must all play our part inprotecting the environment. Correctvehicle usage and the authorizeddisposal of waste, cleaning a

DVD player controls1./ (Play/Pause): Press to play or pause a CD, DVD orflash/thumb drive track.2.(Stop): Press to stop the current DVD, CD/MP3, or fl

5. / (Headphones/Speakers): Press to activate dual play mode oneither headrest system. During dual play mode, the following happens:a. Rear speakers t

Remote controlUnless otherwise stated, all operations can be carried out with theremote control. Always point the remote control directly at the playe

2. Cursor controls: Use in various active menus to advance the cursorup/down/left/right. When not in a menu, the left and right cursor controlsdecreas

15. MEDIA for Monitor A: In Dual Play mode, press MEDIA repeatedlyto select from the possible media sources: (Monitor A, Monitor B, AM,FM1, FM2, SR1,

Battery replacementBatteries are supplied with theremote control unit. Since allbatteries have a limited shelf life,replace them when the unit fails t

where indicated on the left and right hand sides of the system. Refer toWired Headphones following.To install the batteries, removethe screw on the co

Ensure that the headphones are turned off when not in use. Afterapproximately one minute of not being in use (no infrared signal isreceived), the wire

Dual Play: Dual play is when the rear seat passengers choose to listento a different playing media than the front seat passengers. With theDVD and rea

Radio interaction: If your vehicle is equipped with a non-touchscreenaudio system, you can press AUX on the radio repeatedly until DVDappears in the d

Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.WARNING: Please read the section Airbag Supple

Aspect ratio (TV display type)This screen allows you to select theviewing size and shape of the videodisplayed on the LCD screen. This isdisc dependen

2. Press / to ’highlight’ the monitor icon. (A disc will appearbeneath the icon signifying it is the current selection.)3. Pressto select and enter th

Speaker setupThis screen allows you to adjust theaudio balance for your speakers. Toaccess:1. Press SETUP on the remote to access the menu options.2.

4. Press / to chose from Sharpness, Brightness, Contrast, Gamma(Color), Hue, Saturation and Luma-Delay.General setup — screen exitTo exit the setup sc

General informationNote: DVDs are formatted byregions. US and Canada systems canonly play region 1 DVDs and Mexicosystems can only play region 4DVDs.

Read all of the safety and operating instructions before operating thesystem and retain for future reference.Do not attempt to service, repair or modi

Federal Communication Commission (FCC) ComplianceChanges or modifications not approved by Ford Lincoln-Mercury couldvoid user’s authority to operate t

Foreign substancesExercise care to prevent dirt and foreign objects from entering the DVDplayer compartment. Be especially careful not to spill liquid

SINGLE ZONE CLIMATE CONTROL WITH REAR PASSENGERCOMPARTMENT CLIMATE CONTROL1.Defrost: Distributes outside air through the windshield defrostervents and

4. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. A/Cengages automaticall

• How far (if at all) the driver was depressing the acceleratorand/or the brake pedal; and• How fast the vehicle was travelling; and• Where the driver

Operating tips• To reduce fog build-up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build-up

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS AND REAR PASSENGER COMPARTMENTCLIMATE CONTROL (IF EQUIPPED)Temperature conversion: To switch

• : Distributes air through the instrument panel vents.•: Distributes air through the instrument panel vents, floor ventsand rear seat floor vents.•:

10. Power/cabin temperature: Press to activate/deactivate theclimate control system. When the system is off, outside air is preventedfrom entering the

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL (NAVIGATIONBASED–IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Message

5. Passenger heated seat (if equipped): Press to control thepassenger heated seat. Refer to Front seating in the Seating and SafetyRestraints chapter

TOUCHSCREEN FUNCTIONSTemperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the Instrument cluster chapter.Front

Max A/C– Distributes recirculated air through the instrument panelvents to cool the vehicle. This re-cooling of the interior air is moreeconomical and

• To improve the A/C cool down, drive with the windows slightly openfor 2–3 minutes after starting the vehicle or until the vehicle has“aired out.”• A

AUXILIARY CLIMATE CONTROL1.Fan speed: Turn to select the desired fan speed.2.: Distributes air through the rear vents.3.: Distributes air through the

Additionally, when you connect to Traffic, Directions andInformation (if equipped, U.S. only) the service uses GPStechnology and advanced vehicle sens

REAR WINDOW DEFROSTERRThe rear defroster control is located on the climate control panel andworks to clear the rear window of fog and thin ice.The ign

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the low beam headlampso

3. Turn the ignition on and then back to off.4. Turn the headlamp control to the autolamp position. The headlampswill turn on.5. Wait the desired amou

Flash-to-passPull and release to activate.Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the igni

Note: If the battery is disconnected, discharged, or a new battery isinstalled, the dimmer switch requires re-calibration. Rotate the dimmerswitch fro

5. Locate the vertical adjuster oneach headlamp. Using a Phillips #2screwdriver, turn the adjuster eitherclockwise (to adjust down) orcounterclockwise

Your vehicle may have readinglamps within the rear dome lamp(s).Press the switches on either side ofthe dome lamp to turn on thelamps.Your vehicle may

Examples of acceptable condensation are:• Presence of thin mist (no streaks, drip marks or droplets)• Fine mist covers less than 50% of the lensExampl

Function Number of bulbsTradenumberFog lamp 2 H11Map lamp 2 12V6WDome/reading lamps 6 578To replace all instrument panel lights - see your authorized

Replacing front parking lamp/turn signal bulbs1. Make sure headlamp switch is in the off position, then open the hood.2. Reach behind the headlamp ass

EXPORT UNIQUE (NON–UNITED STATES/CANADA) VEHICLESPECIFIC INFORMATIONFor your particular global region, your vehicle may be equipped withfeatures and o

Replacing license plate lamp bulbs1. Make sure the headlamp switch isin the off position.2. Remove the two screws from thelicense plate lamp assembly

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Rear window wiper/washer controlsFor rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select:2 — Normal spe

ILLUMINATED VISOR MIRRORLift the mirror cover to turn on thevisor mirror lamp.Slide-on-rod featureThe visor will slide back and forthon the rod for in

CLOCK (IF EQUIPPED)Press the right (+) control to movethe time display forwards.Press the left (-) control to movethe time display backwards.ELECTRONI

Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the on p

2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons.3. Slowly d

Second row center console features (if equipped)The second row center consoleincorporates the following features:• Flip forward armrest to provide afl

Refrigerator: Briefly press andhold the COOL side of thecontrol.The indicator light on thecool side of the switch willilluminate and the indicator lig

Auxiliary power points can be found in the following locations:• Near the floor in the front console bin on the passenger’s side• In the center consol