Ford 2004 Taurus v.1 Manuel d'utilisateur

Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 13Entertainment Systems 15AM/FM stereo 15AM/FM stereo cassette 16AM/FM stereo w

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa

• After step 3, the restraint system warning light (airbag light) will beturned on for three seconds.4. Within 10 seconds of the light turning on, buc

Failure to inspect and if necessary replace the safety beltassembly under the above conditions could result in severepersonal injuries in the event of

crash severity are appropriate to activate these devices. Refer to thePersonal Safety System section in this chapter.Important supplemental restraint

Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause thoseobjects to be propelled by the

How do the air bag supplemental restraints work?The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to noti

sensors that are part of the front passenger’s seat and safety belt. Thesensors are designed to detect the presence of a properly-seatedoccupant and d

The front passenger sensing system is designed to enable (may inflate)the right front passenger’s frontal airbag anytime the system senses thata perso

An out of position front center occupant could affect thedecision of the front passenger sensing system.If it is necessary to modify an advanced front

Do not lean your head on the door. The side air bag could injureyou as it deploys from the side of the seatback.Do not attempt to service, repair, or

not of the type sufficient to cause activation. Side air bags are designedto inflate in side-impact collisions, not roll-over, rear-impact, frontal or

Brake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON

vehicle. Accident statistics suggest that children are safer when properlyrestrained in the rear seating positions than in the front seating position.

lap/shoulder belt to fit properly. Generally this is when they weigh about80 lbs (about 8 to 12 years old).Booster seats should be used until you can

• Those with a high back.If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo

SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully fo

provide upper torso restraint for children up to 36 kg (80 pounds)using an upper torso harness and a belt-positioning booster.Ford recommends the use

1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear

8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly move the seat forwardand back to m

The rear seats of your vehicle are equipped with built-in tether strapanchors located behind the seats as described below.The tether anchors in your v

4. Open the tether anchor cover.On wagons, snap the tether anchorcover off the anchor under the loadfloor.5. Clip the tether strap to the anchor as sh

Engine oil pressure: Illuminateswhen the oil pressure falls below thenormal range, refer to Engine oil inthe Maintenance andspecifications chapter.Tra

If the tether strap is clipped incorrectly, the child safety seatmay not be retained properly in the event of a collision.6. Install the child safety

The lower anchors for child seatinstallation are located at the rearsection of the rear seat between thecushion and seat back. The LATCHanchors are be

STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo

Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,

• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).• Turn the key to 4 (ON) withoutturning the key to 5 (START).Make sure the

• If the driver’s safety belt is fastened, the light may not illuminate.Starting the engine1. Turn the key to 4 (ON) withoutturning the key to 5(START

Using the engine block heater (if equipped)An engine block heater warms the engine coolant which aids in startingand heater/defroster performance. Use

Refer to Brake system warninglight in the Instrument Clusterchapter for information on the brakesystem warning light.Four-wheel anti-lock brake system

Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake

and gravel roads. The system will allow your vehicle to make better useof available traction in these conditions.During Traction Control娂 operation,th

GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera

It is also important to maintain a proper power steering fluid level in thepower steering fluid reservoir:• Do not operate the vehicle with a low powe

3. Start the vehicle.If it is necessary to use the above procedure to move the gearshift lever,it is possible that a fuse has blown or the vehicle’s b

Hold the brake pedal down while you move the gearshift leverfrom P (Park) to another position. If you do not hold the brakepedal down, your vehicle ma

To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)Always set the parking brake full

If your vehicle gets stuck in mud or snowIf your vehicle gets stuck in mud or snow, it may be rocked out byshifting from forward and reverse gears, st

Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue loador king pin w

GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).

10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), and driver only (68 kg [150 lbs]). Consult your dealership (orthe RV

The amount of weight that you can tow depends on the type of engine inyour vehicle. See the following charts:3.0L 2-Valve Vulcan EngineModel Passenger

Preparing to towUse the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. See your dealer or a reliable trai

Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe

• Consult your local motor vehicle speed regulations for towing a trailer.• To eliminate excessive shifting, use a lower gear. This will also assistin

In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer or flatbed transport vehicle) yourvehicle

GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program

Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will

If your vehicle is a sedan, the fuelpump shut-off switch is located onthe right side of the trunk behindthe trunk liner.If your vehicle is a wagon, th

FUSESIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check th

Passenger compartment fuse panelThe fuse panel is located below and to the left of the steering wheel bythe brake pedal. Remove the panel cover to acc

Fuse/relaylocationFuse ampratingPassenger compartment fuse paneldescription14 — Not used15 10A Left headlamp16 10A Not used (spare)17 15A Stop lamp, S

Fuse/relaylocationFuse ampratingPassenger compartment fuse paneldescription30 10A Courtesy lighting, Battery saver, Powermirrors, Decklid lamp, Power

Power distribution boxThe power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protec

AM/FM STEREO (IF EQUIPPED)1. Clock: To set the hour, press andhold the H control. When thedesired hour appears, release thecontrol.To set the minute,

The high-current fuses are coded as follows.Fuse/relaylocationFuse ampratingPower distribution box description1 60A** Fuse junction panel2 30A** Power

Fuse/relaylocationFuse ampratingPower distribution box description18 — Not used19 — Not used20 — Not used21 — Not used22 10A* A/C clutch relay, PCM ke

If you use the temporary spare tire continuously or do not followthese precautions, the tire could fail, causing you to lose controlof the vehicle, po

If the vehicle slips off the jack, you or someone else could beseriously injured.2. Place gearshift lever in P (Park),turn engine OFF, block thediagon

3. If equipped with a wheel coverthat’s bolted on, loosen the fiveplastic nuts with the lug nutwrench.4. Remove the center ornament or wheel cover fro

10. Remove the jack and fullytighten the lug nuts in the ordershown.11. Return the flat tire, jack and lugwrench to their proper storagelocations. Mak

When a wheel is installed, always remove any corrosion, dirt orforeign materials present on the mounting surfaces of the wheelor the surface of the fr

Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable. Make th

2. Start the engine of the disabled vehicle.3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disc

AM/FM1/FM2; tune to a station, press and hold a preset button untilsound returns.8. Tune: Press/ to changefrequency down/up.9. Seek: Press and release

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or

The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedu

from Ford and Lincoln Mercury dealership management, recognized fortheir business leadership qualities.What the Board needsTo have your case reviewed

Making a decisionBoard members review all available information related to eachcomplaint, including oral presentations, and arrive at a fair and impar

In the CAMVAP program, impartial third-party arbitrators conducthearings at mutually convenient times and places in an informalenvironment. These impa

ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro

2. Clock: To set the hour, press andhold the H control. When thedesired hour appears, release thecontrol.To set the minute, press and holdthe M contro

3. The vehicle is out of service for repair of nonconformities for a total ofmore than 30 calendar days (not necessarily all at one time)In the case o

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips.• Always

• 3.0L Vulcan engine• 3.0L Duratec engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PL

WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub

• Do not use household cleaning products or glass cleaners, which canstain and discolor the fabric and affect the flame retardant abilities ofthe seat

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTSYour Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect i

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel.2. Go to the front of the vehicle a

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.0L V6 Vulcan engine1. Automatic transmission fluid dipstick2. Brake fluid reservoir3. Air filter ass

11. Dolby威 noise reduction:Reduces tape noise and hiss whileplaying a tape, press toactivate/deactivate.12. Side 1–2: Press to change tapedirection.13

3.0L DOHC V6 Duratec engine1. Automatic transmission fluid dipstick2. Brake fluid reservoir3. Air filter assembly4. Battery5. Engine oil dipstick6. En

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

Checking and adding washer fluid for the liftgate (if equipped)The opening for the reservoir islocated on the passenger side underthe tail lamp. Refil

5. Locate and carefully remove theengine oil indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.• If th

Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t

Ford production and aftermarket (Motorcraft) oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedtha

Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lightedsubstances to come near th

• The vehicle may need to be driven 16 km (10 miles) or more torelearn the idle and fuel trim strategy.• If you do not allow the engine to relearn its

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be atthe “cold fill level” or within the“col

Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, maydarken the color of Motorcraft Premium Gold Engine Coolant fromyellow to golden tan

21. EJ (Eject): Press to eject atape.AUDIO SYSTEM WITH AM/FM STEREO/SINGLE CD PLAYER(IF EQUIPPED)1. Clock: To set the hour, press andhold the H contro

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap.5. Fill the coolant reservoi

Severe climatesIf you drive in extremely cold climates (less than –36° C[–34° F]):• It may be necessary to increase the coolant concentrationabove 50%

The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stopsbefore completely rem

clothing and wash skin thoroughly with soap and water. Repeated orprolonged skin contact with fuel liquid or vapor causes skin irritation.• Be particu

When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke whilerefueling. Fuel vapor is extreme

be void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used.The fuel system may be und

FFV engine (if equipped)Your vehicle is designed to use (E85) Fuel Ethanol, “Regular” unleadedgasoline or any percentage of the two fuels combined.U.S

If you are experiencing a rough or rolling idle after start-up with theoutside temperature above 27° C (80° F), the idle should improve within10 to 30

The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fu

Calculation 2: Divide total miles traveled by total gallons used.Keep a record for at least one month and record the type of driving (cityor highway).

Seating and Safety Restraints 81Seating 81Safety restraints 85Air bags 101Child restraints 109Driving 122Starting 122Brakes 126Traction control 128Tra

5. Fade: Press / to shiftsound to the rear/front speakers.6. Scan: Press to hear a briefsampling of all listenable radiostations or CD tracks. Press a

• Use recommended engine oil. Refer to Lubricant specifications inthis chapter.• Perform all regularly scheduled maintenance items. Follow therecommen

• Use only unleaded fuel (or E85, if equipped with the 3.0L FFV V6engine).• Avoid running out of fuel.• Do not turn off the ignition while your vehicl

Board Diagnostics System (OBD-II). This OBD-II system protects theenvironment by ensuring that your vehicle continues to meetgovernment emission stand

CHECKING AND ADDING POWER STEERING FLUIDCheck the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules. If a

3.0L DOHC V6 Duratec engine4. Check the fluid level in thereservoir. It should be between theMIN and MAX lines. Do not addfluid if the level is within

operated for an extended period at high speeds, in city trafficduring hot weather or pulling a trailer, the vehicle should beturned off for about 30 m

High fluid levels can be caused by an overheating condition.Adjusting automatic transmission fluid levelsBefore adding any fluid, make sure the correc

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

Glossary of tire terminology• Tire label: A label showing the OE (Original Equipment) tire sizes,recommended inflation pressure and the maximum weight

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

15. Power/volume: Press to turnON/OFF; turn to increase ordecrease volume levels.16. EJ (Eject): Press to eject a CD.17. AM/FM: Press to choose afrequ

Letter rating Speed rating - km/h (mph)Q 159 km/h (99 mph)R 171 km/h (106 mph)S 180 km/h (112 mph)T 190 km/h (118 mph)U 200 km/h (124 mph)H 210 km/h (

specified government test course. For example, a tire graded 150would wear one and one-half (11⁄2) times as well on the governmentcourse as a tire gra

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation than those of “P” typetires; t

Information on “T” type tiresT145/80D16 is an example of a tiresize.Note: The temporary tire size foryour vehicle may be different thanthis example.1.

recommends the use of a digital or dial type tire pressure gauge ratherthan a stick type of tire pressure gauge.Use the recommended cold inflation pre

5. Repeat this procedure for each tire, including the spare.Note: Some spare tires require higher inflation pressure than the othertires.6. Visually i

• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)2004 Taurus (tau)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specific

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive (4WD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can be corrected by rotati

the tread is worn down to 4mm (1/16th of an inch). When you see these“wear bars”, the tire is worn out and should be replaced.Inspect your tires frequ

Highway hazardsNo matter how carefully you drive there’s always the possibility that youmay eventually have a flat tire on the highway. Drive slowly t

5. Line up the CD with the grooveof the disc holder. Ensure that thelabel on the CD faces downwards.6. Press the disc holder until it lockssecurely in

MOTORCRAFT PART NUMBERSComponent 3.0L V6 Vulcanengine3.0L FFV V6engine3.0L DOHC V6Duratec engineAir filterelement1FA-1683 FA-1683 FA-1683Fuel filter F

REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid MotorcraftHighPerformanceDOT 3 MotorVehicle BrakeFluidAll Between MAXand MIN onres

Fluid Ford PartNameApplication CapacityAutomatictransaxle -AX4SMotorcraftMERCON威VATF3.0L V6 Vulcanengine11.6L (12.2quarts)Windshieldwasher fluid -Fron

ItemsFord PartName orequivalentFord PartNumberFordSpecificationLock cylinders Penetrating andLock LubricantMotorcraft XL-1 noneAutomatictransaxle (AX4

in an automatic transmission that requires use of the MERCON威 typefluid. However, these dual usage fluids may be used in transmissions thatrequire the

523412004 Taurus (tau)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specifications225

IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt

Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea

Transmission/Transaxle code designationsYou can find a transmission/transaxle code on the vehicle certificationlabel which is located on the door pill

Code Transmission DescriptionR Automatic 5–speed overdrive (5R55S)Passenger car application:Code Transmission/Transaxle DescriptionFront wheel drive m

• Tighten very loose tapes by inserting a finger or pencil into the holeand turning the hub.• Remove loose labels before inserting tapes.• Allow tapes

FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford or Ford

Floor matsInterior trim kitsLeather wrapped steering wheelsScuff platesSpeed controlLifestyleBike racksCargo organization and managementEngine block h

AAccessory delay ...47Air bag supplemental restraintsystem ...101–102, 107and child safety seats ...

Cleaning your vehicleengine compartment ...172instrument panel ...174interior ...174inte

Engine oil ...182checking and adding ...182dipstick ...182filter, specifica

KKeyless entry system ...74Keyspositions of the ignition ...122LLampsautolamp system ...29bulb replacementspec

Remote entry systemilluminated entry ...73locking/unlocking doors ...67opening the trunk ...71Roadside as

Vehicle Identification Number(VIN) ...227Vehicle loading ...134Ventilating your vehicle

238

239

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Passenger air

240

• Under normal weather conditions, do not leave the air flow selector inMAX A/C or OFF when the vehicle is parked. This allows the vehicleto “breathe”

1. OFF: Outside air is shut out andthe fan will not operate.2. A/C: Press to turn on and manually control the air conditioning in allmodes except(Defr

fog from the windshield. Outside air and A/C will be automaticallyengaged to assist in clearing the windshield.10. Rear defrost control: Press todefro

5. Direct the outer instrument panel vents towards the side windowsTo increase airflow to the outer instrument panel vents, close the ventslocated in

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola

Maintenance and Specifications 177Engine compartment 179Engine oil 182Battery 185Fuel information 191Part numbers 220Refill capacities 221Lubricant sp

High beamsPush the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate.Flash to passPull toward you slightly to acti

• (1) Eight feet• (2) Center height of lamp toground• (3) Twenty five feet• (4) Horizontal reference line2. Measure the height of the headlamp bulb ce

To see a clearer light pattern foradjusting, you may want to blockthe light from one headlamp whileadjusting the other.5. Locate the vertical adjuster

Dome lamps and map lamps• ON orD: The dome light willstay on.• DOOR or middle position: Thedome light will only come on if adoor is opened.• OFF or: T

Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbs mustbe marked with an authorized “D.O.T.” for North America an

Replacing headlamp bulbsTo remove the headlamp bulb:1. Make sure headlamp switch is inOFF position.2. Remove the bolt from theheadlamp housing.3. At t

5. Disconnect the electricalconnector from the bulb by pullingrearward.6. Remove the bulb retaining ring byrotating it counterclockwise.7. Remove the

2. Install the bulb retaining ring over the plastic base and lock the ringby rotating clockwise until it snaps into place.3. Connect the electrical co

5. Carefully pull bulb straight out ofthe socket and push in the newbulb.6. Install the bulb socket into thelamp assembly by rotating itclockwise.7. C

Replacing high-mount brakelamp bulbs — Wagon only1. Open liftgate.2. Remove two screw covers, screwsand handle from liftgate.3. Remove two screws and

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

7. Carefully lift the lamp assemblyaway from the liftgate.8. Remove the bulb socket byrotating it counterclockwise andpulling it out from the lampasse

3. On the underside of the spoiler,remove the two decorative screwcovers (on the LED module).4. Remove the two screws that areholding the LED module i

Sedan1. Make sure headlamp switch is inOFF position and remove twoscrews, grommets and the licenseplate lamp assembly from the trunklid.2. Carefully p

6. Install the bulb socket into the lamp assembly by rotating it clockwise.7. Install the lamp assembly on the vehicle with three nut and washerassemb

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Press the washer control to activatethe rear washer. The wiper willcome on when the washer control ispressed, if it is not already on.Changing the wip

Never adjust the steering wheel when the vehicle is moving.ILLUMINATED VISOR MIRROR (IF EQUIPPED)To turn on the visor mirror lamps,lift the mirror cov

POWER WINDOWSWhen closing the powerwindows, you should verifythey are free of obstructions andensure that children and/or petsare not in the proximity

change from the normal, clear state to the darkened, non-glare statewhen bright light (glare) reaches the mirror from behind the vehicle atnight.Do no

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is

Fuel pump shut-off switch In the event of an accident thesafety switch will automatically cut off the fuel supply to theengine. The switch can also be

3. Press the SET ACC control andrelease it.4. Take your foot off the acceleratorpedal.5. The CRUISE indicator light onthe instrument cluster will turn

Increasing speed while using speed controlThere are three ways to set a higherspeed:• Press and hold the SET ACCcontrol until you get to thedesired sp

• Depress the brake pedal. This willnot erase your vehicle’spreviously set speed.• Press the speed control OFFcontrol.Note: When you turn off the spee

Use only soft cups in the cupholder. Hard objects can injure youin a collision.If your vehicle is equipped with the column shift and a bench seat, it

Selectable featuresResetPress this control to select and reset functions shown in the INFO menuand SETUP menu.Info menuThis control displays the follo

Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in liters/100 km ormiles/U.S. gallon.If you calcu

Compass display (if equipped)The compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast anten

5. Press and hold the RESET untilthe message center display changesto show the current zone setting.6. Release the RESET control, thenslowly press RES

Setup menuPress this control for the followingdisplays:• Language• Units (English/Metric)• System CheckLanguage1. Select this function from theSETUP m

System checkSelecting this function from theSETUP menu causes the messagecenter to cycle through each of thesystems being monitored. For eachof the mo

BREAKING-IN YOUR VEHICLEYour vehicle does not need an extensive break-in. Try not to drivecontinuously at the same speed for the first 1,600 km (1,000

This acts as a reminder that these warning conditions still exist withinthe vehicle.Warnings StatusDriver’s door ajar Warning cannot be reset (CLOSEDO

CHECK ENGINE TEMPERATURE. Displayed when the enginecoolant is overheating. Stop the vehicle as soon as safely possible, turnoff the engine and let it

CHECK TRACTION CONTROL (if equipped). Displayed when theTraction Control娂 system is not operating properly. If this warning stayson, contact your deal

POSITIVE RETENTION FLOOR MATPosition the driver floor mat so thatthe eyelet is over the pointed end ofthe retention post and rotateforward to lock in.

The liftgate and liftgate window should be closed before driving yourvehicle. If not, possible damage may occur to the liftgate lift cylindersand atta

Do not place any objects on the cargo area cover. They mayobstruct your vision or strike occupants of the vehicle in thecase of a sudden stop or colli

The cover may cause injury in a sudden stop or accident if it isnot securely installed.Cargo utility hooks (Sedan)The utility hooks located inside the

KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w

4. Press the power door unlock control three times.5. Turn the ignition back to ON. The horn will chirp.6. Press the unlock control, then press the lo

To open the luggage compartmentdoor (lid) from within the luggagecompartment, pull the illuminated“T” shaped handle and push up onthe trunk lid. The h

• how far (if at all) the driver was depressing the accelerator and/or thebrake pedal;• how fast the vehicle was traveling; and• where the driver was

Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment.The rem

If any of the doors or liftgate (wagon) are not properly closed the hornwill make two quick chirps, and the parklamps will not flash. As soon asall ve

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery.4. Insert the new battery. Ref

6. Within 20 seconds press any button on the remote entry transmitter.Note: If more than 20 seconds have passed you will need to start theprocedure ov

• Tail lampsOn vehicles not equipped with the autolamps feature, only the followingitems will illuminate:• Puddle lamps (if equipped)• Park lamps• Tai

• activate or deactivate the autolock feature.The keypad can be operated with the factory set 5–digit entry code; thiscode is located on the owner’s w

Unlocking and locking the doors using keyless entryTo unlock the driver’s door, enter the factory set 5-digit code or yourpersonal code. Each number m

6. Press the unlock control, then press the lock control. Note: The hornwill chirp twice if autolock was deactivated or chirp twice then honk(two shor

Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 3(OFF) position.TheTHEFTindicator will flashevery two seconds when

1. Insert a previously programmedcoded key into the ignition.2. Turn the ignition from the 3(OFF) position to the 4 (ON)position. Keep the ignition in

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-

Arming the systemWhen armed, this system will respond if unauthorized entry isattempted. When unauthorized entry occurs, the system will flash thehead

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

Using the manual lumbar support (if equipped)The lumbar control is located on thefront of the seat cushion.Turn to adjust lumbar support.Adjusting the

Adjusting the front power seat (if equipped)The control is located on the outboard side of the seat cushion.Press to raise or lower the frontportion o

Make sure that the safety belt for the rear center passenger is properlyrouted over the rear seatback.3rd seat (wagon only)The third seat faces the re

To close the seat, make sure the safety belts are properly stowed, thenlift the remote latch release and push the seat down until it latches. Pullup o

the system. Rather, it means the Personal Safety System determined theaccident conditions (crash severity, belt usage, etc.) were notappropriate to ac

Air bags can kill or injure a child in a child seat. NEVER place arear-facing child seat in front of an active air bag. If you mustuse a forward-facin

manner in response to the occupant’s forward momentum. This helpsreduce the risk of force-related injuries to the occupant’s chest bylimiting the load

All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag (SRS) isprovided.It is extreme

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.Energy management retractorsYour vehicle has a seat belt system equipped w

How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt

After any vehicle collision, the seat belt system at all outboardseating positions (except driver, which has no “automatic lockingretractor” feature)

Safety belt usage sensorsThe driver and front outboard passenger safety belt buckles areequipped with sensors that detect if the safety belts are fast

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ

shoulder and chest. Be sure the belt is not twisted. If the belt is twisted,remove the twist. Insert the tongue into the proper buckle for yourseating

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war

If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2minutes h

Reasons given... Consider...“Crashes are rareevents”36700 crashes occur every day. The more wedrive, the more we are exposed to “rare” events,even for

Do not sit on top of a buckled safety belt to avoid the BeltMinder chime. Sitting on the safety belt will increase the risk ofinjury in an accident. T