Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 13Entertainment Systems 15AM/FM stereo with CD 15AM/FM stereo cassette with CD
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa
• a readiness light and tone• a diagnostic module• and the electrical wiring which connects the componentsSeveral air bag system components get hot af
Do not use accessory seat covers. The use of accessory seatcovers may prevent the deployment of the side air bags andincrease the risk of injury in an
occupied. The air bag was designed to inflate between the door paneland occupant to further enhance the protection provided occupants inside impact co
• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and/or light are repaired.If any of these things ha
If the shoulder belt portion of a combination lap and shoulder belt can bepositioned so it does not cross or rest in front of the child’s face or neck
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
Follow all instructions provided by the manufacturer of thebooster seat.Never put the shoulder belt under a child’s arm or behind theback because it e
When installing a child safety seat:• Review and follow the informationpresented in the Air bagsupplemental restraint system(SRS) section in this chap
Installing child safety seats with combination lap and shoulderbeltsThe rear seat head restraints must be removed when using a childseat.Air bags can
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
Brake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON
7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat.
The tether strap anchors in your vehicle are in the following positions:Attach the tether strap onlyto the appropriate tetheranchor as shown. The teth
4. Clip the tether strap to theanchor as shown.The arrow in the above graphicpoints toward the front of thevehicle.If the tether strap is clippedincor
Your vehicle has LATCH anchors for child seat installation at thefollowing locations:The anchors on both sides of thecenter of the rear seat are provi
Attach LATCH lower attachments of the child seat only to theanchors shown.If you install a child seat with rigid LATCH attachments, do not tightenthe
STARTINGPositions of the ignition1. LOCK, locks the gearshift leverand allows key removal.2. ACCESSORY, allows the electricalaccessories such as the r
If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf
If starting a vehicle with a manualtransmission:• Make sure the parking brake isset.• Push the clutch pedal to thefloor.3. Turn the key to 3 (RUN) wit
Starting the engine1. Turn the key to 3 (RUN) withoutturning the key to 4 (START). Ifthere is difficulty in turning the key,rotate the steering wheel
BRAKESOccasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-o
Engine oil pressure: Illuminateswhen the oil pressure falls below thenormal range, refer to Engine oil inthe Maintenance andspecifications chapter.Low
Parking brakeTo set the parking brake (1), pullthe parking brake handle up as faras possible.The BRAKE warning lamp willilluminate and will remainillu
PREPARING TO DRIVE YOUR VEHICLEUtility vehicles have a significantly higher rollover rate thanother types of vehicles.In a rollover crash, an unbelted
2. Locate the access cover plate tothe brake-shift interlock override. Itis located on the top of the steeringcolumn.3. Insert a tool (or a screwdrive
Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position andremove the key wheneve
Understanding the gearshift positions of the 4–speed automatictransaxleYour transaxle is equipped with an adaptive learning strategy found inthe vehic
N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D
1 (First)• Provides maximum engine braking.• Allows upshifts by moving gearshift lever.• Will not downshift into 1 (First) at high speeds; allows for
When starting a vehicle with a manual transaxle, you must:1. Put the gearshift lever in theneutral position.2. Hold down the brake pedal.3. Depress th
Recommended shift speedsUpshift according to the following charts for best fuel economy:Upshifts when accelerating (recommended for best fueleconomy)1
Parking your vehicle1. Apply the brake and shift into theneutral position.2. Set the parking brake.3. Shift into 1 (First).124R35124R35Driving129
Key-in-ignition warning chime: Sounds when the key is left in theignition in the OFF/LOCK or ACC position and the driver’s door isopened.Headlamps on
4. Turn the ignition to position 1(LOCK) to shut the engine off andremove the ignition key.Do not park your vehicle in Neutral, it may move unexpected
Using the electronic shift 4x4 systemAUTO- Full power to front wheels, at all times; power to the rear wheelsas required by driving conditions. Used f
Maintain steering wheel control at all times, especially in rough terrain.Since sudden changes in terrain can result in abrupt steering wheelmotion, m
If your vehicle gets stuckIf your vehicle gets stuck in mud or snow it may be rocked out byshifting between forward and reverse gears, stopping betwee
Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.
when you are driving over sand, apply the accelerator slowly and avoidspinning your wheels. If the vehicle does slide, steer in the direction ofthe sl
Apply just enough power to the wheels to climb the hill. Too muchpower will cause the tires to slip, spin or lose traction, resulting in loss ofvehicl
is equipped with a Four Wheel Anti-Lock Brake System (ABS), apply thebrake steadily. Do not “pump” the brakes. Refer to the Brakes section ofthis chap
front door lock facing or door latch post pillar. Failure to follow tirepressure recommendations can adversely affect the way your vehiclehandles. Do
REVERSE SENSING SYSTEM (IF EQUIPPED)The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when R (Reverse
Odometer: Registers the totalkilometers (miles) of the vehicle.Trip odometer: Registers thekilometers (miles) of individualjourneys. To reset, tap on
The RSS detects obstacles up to 2meters (6.5 ft.) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the f
that is higher than the bottom of the hubs (for trucks) or the bottom ofthe wheel rims (for cars). Traction or brake capability may be limitedand your
• Maximum Trailer Weight: Maximum weight of a trailer the loadedvehicle (including occupants and cargo) is permitted to tow. It isdetermined by subtra
Calculating the load your vehicle can carry/tow1. Use the appropriate maximum GCWR chart (in the Trailer Towingsection in this chapter) for your type
4x2GCWR (Gross Combined Weight Rating)/Trailer WeightsEngine MaximumGCWR - kg(lbs.)Trailer WeightRange - kg(lbs.)Maximumfrontal area oftrailer - m2(ft
Do not exceed the GVWR or the GAWR specified on thecertification label.Towing trailers beyond the maximum recommended gross trailerweight exceeds the
Trailer lampsTrailer lamps are required on most towed vehicles. Make sure yourtrailer lamps conform to local and Federal regulations. See your dealer
When backing down a ramp during boat launching or retrieval:• do not allow the static water level to rise above the bottom edge ofthe rear bumper.• do
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
AM/FM STEREO / SINGLE CD RADIO1. Balance: Press/ to shiftsound to the left/right speakers.2. Fade: Press/ to shiftsound to the front/rear speakers.3.
This switch is located in the frontpassenger’s footwell, behind aflip-up cover, by the kick panelaccess cover.To reset the switch:1. Turn the ignition
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 5A Canister vent control solenoid2 5A Blow
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description6 10A Flasher unit, Reversing lamps,Park Aid Module (PAM)7 10A Passive Anti
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description22 15A Not used23 20A Horn relay24 15A Stoplamps, High mountedstoplamp, Tra
If the battery has been disconnected and reconnected, refer to theBattery section of the Maintenance and specifications chapter.The high-current fuses
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescriptionH/L RELAYMICRO— Headlamp (high/low, right/leftrelay)HTD SEATS 30A Heated seats (if eq
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescriptionADD FAN 40A**(2.0 L)50A(3.0 L)Add fanEEC MAIN ISO — EEC relayFUEL PUMP ISO — Fuel pum
If you use the temporary spare tire continuously or do not followthese precautions, the tire could fail, causing you to lose controlof the vehicle, po
1. Park on a level surface, activatehazard flashers and place gearshiftlever in P (Park) (automatictransmission) or R (Reverse)(manual transmission).2
5. EJ (eject): Press to eject a CD.6. COMP (Compression): In CDmode, press to bring louder andsofter levels into more comfortablelistening level. The
Before placing the jack under the vehicle, NOTE the jack locations:• Front jacking notches are locatedunder the front suspensionarm.• Rear jacking not
Never use the differentials as ajacking point.To lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a
To stow the full size flat tire in thecargo floor, the long spare tire rodin the tool bag needs to be installed.11. Using the lug wrench, removethe sp
Preparing your vehicleWhen the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, th
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport vehicle) yourvehicl
15. AM/FM: Press to choose afrequency band in radio mode.16. Bass: Press/ toincrease/decrease the bass output.17. Treble: Press/ toincrease/decrease t
GETTING THE SERVICES YOU NEEDAt homeFord Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai
Board membershipThe Board consists of:• Three consumer representatives• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa
Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADAONLY)In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a
If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest F
IN CALIFORNIA (U.S. ONLY)California Civil Code Section 1793.2(d) requires that, if a manufactureror its representative is unable to repair a motor veh
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im
PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD1. Power/volume: Press to turnON/OFF; turn to increase/decreasevolume.2. Scan: Press to hear a briefsampling of
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam
• 2.0L DOHC I4 — Zetec Engine• 3.0L DOHC V6 — Duratec Engine• Never wash or rinse the engine while it is running; water in therunning engine may cause
WINDOWS AND WIPER BLADESThe windshield, rear window and wiper blades should be cleanedregularly. If the wiper does not wipe properly, substances on th
INTERIORFor fabric, carpets, cloth seats, safety belts and seats equipped with sideair bags:• Remove dust and loose dirt with a vacuum cleaner.• Remov
FORD, LINCOLN AND MERCURY CAR CARE PRODUCTSYour Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect i
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
• Manual transmission:1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral).2. Block the wheels.Note: Do not start your e
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.0L DOHC I4 Zetec engine1. Power steering fluid reservoir2. Engine coolant reservoir3. Brake/Clutch f
3.0L DOHC V6 Duratec engine1. Power steering fluid reservoir2. Engine coolant reservoir3. Automatic transmission fluid dipstick4. Brake fluid reservoi
not be inserted into the CD player. The label may peel and causethe CD to become jammed. It is recommended that homemadeCDs be identified with permane
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
3. Set the parking brake and ensure the gearshift is securely latched in P(Park) (automatic transmissions) or 1 (First) (manual transmissions).4. Open
6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.• If the oil level is between the MIN—MAX marks, the oil level isacceptab
5. Fully install the engine oil filler cap by turning the filler cap clockwise1/4 of a turn until it is seated.To avoid possible oil loss, DO NOT oper
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a
If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreco
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “cold fill level” or within the “c
Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, maydarken the color of Motorcraft Premium Gold Engine Coolant fromyellow to golden tan
4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap.5. Fill the coolant reservoi
Locks and Security 65Keys 65Locks 65Anti-theft system 70Seating and Safety Restraints 75Seating 75Safety restraints 85Air bags 96Child restraints 103D
to decrease minutes or TUNE to increase minutes. If your vehiclehas a stand alone clock this control will not function.10. Balance: Press BAL; then pr
Severe climatesIf you drive in extremely cold climates (less than –36° C [–34° F]):• It may be necessary to increase the coolant concentrationabove 50
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsDo not overfill the fuel tank. The pressure in an overfilled tankmay cause leak
• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek med
Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1/8 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref
Your vehicle was not designed to use fuel or fuel additives with metalliccompounds, including manganese-based compounds containing MMT.Repairs to corr
Running out of fuelAvoid running out of fuel because this situation may have an adverseaffect on powertrain components.If you have run out of fuel:• Y
vehicle after the fuel gauge indicates empty, you might not beable to refuel the full amount of the advertised capacity of thefuel tank due to the emp
Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin
Conditions• Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed.• Carrying unnecessary weight may reduce fuel economy (a
• Have the items listed in your scheduled maintenance guide performedaccording to the specified schedule.The scheduled maintenance items listed in the
16. Fast Forward (FF): Press fora slow advance, press and hold for afast advance.17. Rewind (REW): Press for aslow rewind, press and hold for afast re
detected a malfunction. Temporary malfunctions may cause your CheckEngine/Service Engine Soon light to illuminate. Examples are:1. The vehicle has run
CHECKING AND ADDING POWER STEERING FLUIDCheck the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules. If a
The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines
Low fluid levelDo not drive the vehicle if the fluidlevel is at the bottom of the dipstickand the outside temperatures areabove 10°C (50°F).Correct fl
Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may affect transmissionoperation and re
AIR FILTER MAINTENANCERefer to the scheduled maintenance guide for the appropriate intervalsfor changing the air filter element.When changing the air
Note: Failure to use the correct air filter element may result in severeengine damage. The customer warranty may be voided for any damage tothe engine
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
them as indicated in the scheduled maintenance guide. If you notice thatthe tires wear unevenly, have them checked.• Four tire rotationReplacing the t
Do not replace your tires with “high performance” tires or largersize tires.Failure to follow these precautions may adversely affect thehandling of th
PREMIUM IN-DASH SIX CD SOUND SYSTEMAUDIOPHILE IN-DASH SIX CD SOUND SYSTEM1. Seek: Press and releaseSEEK/ for previous/nextstrong station, selection or
MOTORCRAFT PART NUMBERSComponent 2.0L DOHC I4Zetec engine3.0L DOHC V6 DuratecengineAir filter element1FA-1683 FA-1683Fuel filter FG-800-A FG-800-ABatt
Fluid Ford PartNameApplication CapacityFuel tank N/A 2.0L I4 Zetecengine61L (16 gallons)3.0L V6 Duratecengine61L (16 gallons)Power steeringfluidMotorc
Fluid Ford PartNameApplication CapacityEngine coolant4MotorcraftPremium GoldEngine Coolant(yellow-colored)2.0L I4 Zetecengine withmanualtransaxle5.0L
LUBRICANT SPECIFICATIONSItem Ford Part Nameor equivalentFord PartNumberFordSpecificationBody hinges,latches, doorstriker plates androllers, seattracks
Item Ford Part Nameor equivalentFord PartNumberFordSpecificationRear axle (4X4)4Motorcraft SAE80W-90 PremiumRear AxleLubricantXY-80W90-QL WSP-M2C197-A
ENGINE DATAEngine 2.0L DOHC I4 Zetecengine3.0L DOHC V6Duratec engineCubic inches 121 181Required fuel 87 octane 87 octaneFiring order 1-3-4-2 1-4-2-5-
321Maintenance and Specifications226
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea
FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincol
2. Rewind: In CD mode, press untildesired selection is reached.Fast forward: In CD mode, pressuntil desired selection is reached.3. COMP (Compression)
Comfort and convenienceCabin air filtrationCargo netCargo organizersCargo shadesCargo traysCarpeted cargo matCellular phone hands free system with voi
Running barsSoft luggage coverTrailer hitch (Class II)Trailer hitch bars and ballsTrailer hitch receiver coverTrailer hitch wiring adaptorTrailgate ta
For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle:• When adding accessories,
AAir bag supplemental restraintsystem ...96–97, 100and child safety seats ...98description ...
Child safety seats ...106attaching with tether straps ..110in front seat ...108in rear seat ...
refill capacities ...220service points ...188–189starting after a collision ...149Engine block heater ...
Infant seats(see Safety seats) ...106Inspection/maintenance (I/M)testing ...210Instrument panel
Power distribution box(see Fuses) ...154Power point ...49Power steering ...
tire grades ...217treadwear ...216Towing ...143recreation
239
8. Balance: Press BAL; then pressSEL/ to shift sound to theleft/right speakers.Fade: Press FADE; then pressSEL/ to shift sound to therear/front speake
240
AUTOSTORE will flash on the display. When the six strongest stationsare filled, the station stored in preset 1 will begin playing. If there areless th
MACH姞 MP3 AUDIO SYSTEM1. Balance: Press/ to shiftsound to the left/right speakers.2. Fade: Press/ to shiftsound to the rear/front speakers.3. Scan: Pr
5. EJ (Eject): Press to stop andeject a disc. If a disc is ejected andnot removed, the player willautomatically reload the disc and return to radio mo
13. Memory presets: To set a station: Select frequency band AM/FM;tune to a station, press and hold a preset button until sound returns.14. CD door: I
21. Treble: Press / todecrease/increase the treble output.RADIO FREQUENCIESAM and FM frequencies are established by the Federal CommunicationsCommissi
Cleaning 180Maintenance and Specifications 186Engine compartment 188Engine oil 190Battery 194Fuel information 201Air filter(s) 215Part numbers 220Refi
CD/CD PLAYER CAREDo:• Handle discs by their edges only. Never touch the playing surface.• Inspect discs before playing. Clean only with an approved CD
HEATER ONLY SYSTEM1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Air flow selections: Controlsthedirectionoftheairflow
4. Direct the outer instrument panel vents towards the side windowsTo increase airflow to the outer instrument panel vents, close the ventslocated in
Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
HEADLAMP CONTROLRotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlam
Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Lamp (DRL) systemdoes not activate with your tail la
• Push and hold bottom of controlto dim.AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has
4. On the wall or screen you willobserve a light pattern with adistinct horizontal edge of highintensity light towards the right. Ifthis edge is not a
The dome lamp will stay on if thecontrol is moved to the passengerside position. When the control is inthe middle position, the lamp willonly come on
BULBSReplacing exterior bulbsCheck the operation of all the bulbs frequently.Using the right bulbsReplacement bulbs are specified in the chart below.
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
3. Press two tabs and disconnect theelectrical connector from the bulb.4. Remove the rubber boot from thelamp assembly by pulling on one ofthe tabs.5.
6. Without turning, carefully pullbulb out of headlamp assembly.Handle a halogen headlampbulb carefully and keep outof children’s reach. Grasp the bul
Replacing brake/tail/turn/backup lamp bulbsThe brake/tail/turn/backup lamp bulbs are located in the tail lampassembly, one just below the other. Follo
3. Pull the bulb out from the socket and push in the new bulb.4. Install the bulb socket in lamp assembly turning it clockwise,5. To install, press th
MULTI-FUNCTION LEVERWindshield wiper: For intermittentoperation, move control down oneposition.Adjust the rotary control to thedesired speed setting.F
For normal speed rear wiperoperation, rotate control upward toON.To activate the rear washer, rotatethe control to theposition andrelease.Changing the
Never adjust the steering wheel when the vehicle is moving.OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehicle’s overhead console will vary a
•Remove the Velcro pad (2) fromthe storage compartment door (3).• Place Velcro (5) on aftermarkettransmitter (6) opposite ofactuator control (8).• Mea
the storage compartment door (3) or you may break the door latch. Ifthe rubber actuator (1) is the proper length the storage compartmentdoor will clos
The mirror will automatically return to the normal high reflective statewhenever the vehicle is placed in R (Reverse). This helps to ensure abright cl
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury and prevent possibledamage to others, you
One touch downAllows the driver’s window to openfully without holding the controldown. Press completely down onAUTO and release quickly. Pressagain to
Fold-away mirrorsPull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.Heated outside mirrors(if equipped)B
3. Press the SET ACC control andrelease it.4. Take your foot off the acceleratorpedal.5. The indicatorlight on theinstrument cluster will turn on.Note
Reducing speed while using speed controlThere are two ways to reduce a setspeed:• Press and hold the CST controluntil you get to the desiredspeed, the
Use only soft cups in the cupholder. Hard objects can injure youin a collision.Cell phone useThe use of Mobile Communications Equipment has become inc
If you open and close the moon roof repeatedly, the moon roof motormay overheat and shut down for 45 seconds while the motor cools.Do not let children
To install the shade:• Insert the ends of the cargoshade into the mounting featureslocated behind the rear seat onthe rear trim panels.To operate the
To adjust the cross-bar (if equipped) position:1. Loosen the thumbwheel at bothends of the cross-bar (bothcross-bars are adjustable).2. Slide the cros
To reinstall the cross-bar assembly (if equipped) to the roof rackside rails:1. Ensure that both cross-barassemblies are installed with the F(front) a
NO BOUNDARIES RACK SYSTEM (IF EQUIPPED)Your vehicle may be equipped withan optional roof rack. This uniquefeature allows you to carry cargo onan inner
SPECIAL NOTICESSpecial instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplem
3. Slide the inner rack rearward,with an initial pull to release therack from its stowed position, untilit has completely extended andstops.4. Lower t
6. Figure shows foot (A) clickedinto place correctly.7. With the locking tab (B)exposed on the foot, this figureshows the rack is not installedcorrect
To stow the inner rack:1. Rotate the handle on the lift barof the inner rack in the direction ofthe arrows on the handle and pullthe inner rack away f
5. Lift the feet over the side rails and lock them into place.6. Ensure both feet are locked and secured into place.To adjust the cross-bar assembly o
Always stow the inner rack on the roof when using an automatedcar wash.Do not attempt to open the liftgate or rear window when the rackis in the down
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
Locking the doorsTurn the key in the door cylinder to lock all the doors. The park lampswill flash once and the perimeter alarm (if equipped) will sta
The remote entry system allows youto lock or unlock all vehicle doorswithout a key. The remote featurewill only operate when the ignitionis in the OFF
Sounding a panic alarmPressto activate the alarm. To deactivate the feature, press thecontrol again or wait for the alarm to time out in approximately
How to reprogram your remote entry transmittersYou must have all remote entry transmitters (maximum of four)available before beginning this procedure.
Emission warrantyThe New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage,Safety Restraint Coverage, Corrosion Coverage, and 7.3L Power Str
Illuminated entryThe interior lamps illuminate when the remote entry system is used tounlock the door(s).The illuminated entry system will turn off th
Theft indicatorThe theft indicator is located in the instrument cluster.• When the ignition is in the OFF position, the indicator will flash onceevery
Programming spare keysYou can program your own coded keys to your vehicle. Please read andunderstand the entire procedure before you begin.Tips:• A ma
9. Remove the newly programmed coded key from the ignition.If the key has been successfully programmed it will start the vehicle’sengine and the theft
Disarming the systemWhen you disarm the system, the park lamps will flash twice to indicatethe system has been disarmed.You can disarm the system by a
FRONT SEATSNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent
Adjusting the front manual seatLift handle to move seat forward orbackward.Pull lever up to adjust seatback.Adjusting the front power seat (if equippe
Press to raise or lower the rearportion of the seat cushion.Press the control to move the seatforward, backward, up or down.Heated seats (if equipped)
The head restraints can be movedup and down. Lift the head restraintso that it is located directly or asclose as possible behind your head.Push contro
Folding down rear seats1. Raise the rear seat head restraintand remove.2. Place the head restraint underthe front seat for storage.3. Pull the seat re
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
4. Flip seat forward.5. Pull the seatback release straptoward the front seat. Make sure theseat belt buckle heads are fullyextended towards the front
Returning the rear seats to upright position1. Pull seatback up and into uprightposition making sure seatback locksinto place. While holding theseatba
To remove the rear cushion1. Pull the Yellow tab2. Pull the cushion to the outboardside of the vehicle.To install the rear cushion1. Push the cushion
2. Place the head restraint underthe front seat for storage.3. Pull the seat release control oneach side of the seat to release thelocks.4. Flip the s
5. Pull the seatback release straptoward the front seat. Make sure theseat belt buckle heads are fullyextended towards the front of thevehicle and are
Make sure that the seat is firmly locked into position and the theseat belt buckles are exposed.To remove the rear cushion1. Pull the Yellow tab.2. Pu
All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag (SRS) isprovided.It is extreme
BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if thesafety belt assembly automatic locking retractor feature or anyother safety belt function is not op
Automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt
How to disengage the automatic locking modeDisconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic l
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
Safety belt pretensionerYour vehicle is equipped with safety belt pretensioners at the driver andfront passenger seating positions.The safety belt pre
Shorten and fasten the belt whennot in use.Safety belt extension assemblyIf the safety belt is too short when fully extended, there is a 20 cm (8inch)
If... Then...The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition...The safety belt warning light andindicator chi
The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...⬙Crashes are ra
Reasons given... Consider...⬙The people I’m with don’twear belts⬙Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE peop
• the driver’s safety belt is unbuckled• the parklamps/headlamps are in OFF position (If vehicle is equippedwith Autolamps, this will not affect the p
Safety belt maintenanceInspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to ma
Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in
Do not attempt to service, repair, or modify the air bagsupplemental restraint systems or its fuses. See your Ford orLincoln Mercury dealer.Modificati
How does the air bag supplemental restraint system work?The air bag SRS is designed toactivate when the vehicle sustains alongitudinal deceleration su
Commentaires sur ces manuels