Ford 2004 Freestar v.2 Manuel d'utilisateur

The following information is specifically for the Freestar cargovan only; it is in addition to the existing information found onpages 200, 201, 207 an

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

Tips for setting codes:• The factory set code cannot be erased or changed.• The factory code will work even after you have set your own personalcodes.

2. Close all the doors.3. Enter the 5-digit entry code.4. Press and hold the 7 • 8. While holding the 7 • 8, press the 3 • 4.5. Release the 3 • 4.6. R

Theft indicatorThe theft indicator is located on top of the instrument panel.• When the ignition is in the 3 (OFF) position, the indicator will flasho

The correct coded key must be used for your vehicle. The use of thewrong coded key may lead to a “no start” condition.If an unprogrammed key is used i

If successful, the new coded key(s) will start the vehicle’s engine and thetheft indicator will illuminate for three seconds and then go out.If not su

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

Always drive and ride with your seatback upright and the lapbelt snug and low across the hips.Lift handle to move seat forward orbackward.Pull lever u

Press to raise or lower the frontportion of the seat cushion.Press to raise or lower the rearportion of the seat cushion.Press the control to move the

Using the manual lumbar support (if equipped)The lumbar control is located on theinboard side of the seat under thearmrest.Rotate the control to chang

REAR SEATSHead restraintsLift the head restraint so that it is located directly or as close as possiblebehind your head.The head restraints can be mov

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A wa

The cupholder is designed to detach from the seat when subjected toheavy load. The cupholder can be reinstalled by returning to the closedposition.Adj

• 2nd row bench seat (if equipped)Note: This seat can be movedforward to keep a child in aLATCH child restraint attachedto the LATCH anchors at thecen

Note: Place the front row seat in a forward position to allow the 2ndrow to be fully upright.Lift the handle located on the rearlower corner of the se

After entering the 3rd row seat,return the seat from the tumbledposition and latch it to the floor.Operate recline control to return theseatback to th

Second row bench seat tip slide feature1. Push the side easy-entry controlhandle forward and allow the seatback to flip forward.2. Push the seat forwa

After exiting the third row, pushrearward on the cushion of the seatto return the seat to its originalposition.Push the seatback rearward until itlatc

4. From inside the vehicle, pull upon front floor release handle(yellow).5. Rotate the seat rearward at a 30to 45 degree angle.6. With the assist hand

Second row bench seat1. Detach the lap/shoulder beltsfrom both sides of the seat byinserting a seat belt tongue or keyinto the buckle release slot, pu

3. Clip the end of the belt to thestationary portion of the shoulderbelt coming out of the trim panel.The end of the shoulder belt mustbe clipped in o

1. Position the seat in vehicle. Placefirst row seat in a forward positionto allow the second row seat to beinstalled.2. Install seat onto rear pin of

Check fuel cap: Illuminates whenthe fuel cap may not be properlyinstalled. Continued driving withthis light on may cause the Checkengine warning light

4. Rotate seat rearward until theback of the seat latches onto thefloor.5. Operate recline lever and pushthe seat back upright.Ensure seat is latched

3. Lower back of seat onto the reartubs until both release controls latchinto place. Be sure that the seat islocked in place both front and back.Do no

2. If you plan to carry very largeobjects or items that might damagethe center lap/shoulder belt, detachthe belt from the seat. Use a key orseat belt

4. Store the belt in the housingfound on the ceiling by inserting thesmaller tongue in the slot provided.Note: The seat can be stowed withthe safety b

Important: If you don’t let go ofthe number 1 strap before the seatback folds completely, the seat maynot stow flat in the tub. Refer to thelabel atta

8. Pull the number 3 strap on the seat back to tumble seat all the way into the tub in the floor.Do not use the seat anchors as cargo tie downs.Unstow

2. To return the seat back to theseating position, pull the number 1strap, then while holding thenumber 1 strap, pull the number 3strap to raise the s

This is not a position suitable for driving. Do not drive thevehicle with the seat in this position. The safety belts are notfunctional when the seat

3. To return the seat, ensure seatlatching area is free of objects.Then, raise the seat off the liftgatescuff plate and push at the top ofthe seat bac

How does the Personal Safety System work?The Personal Safety System can adapt the deployment strategy of yourvehicle’s safety devices according to cra

Safety belt: Reminds you to fastenyour safety belt. A chime will alsosound to remind you to fasten yoursafety belt.Check transaxle: Illuminates whena

Passenger occupant classification sensor (OCS)A label is located under the front passenger seat which is marked “OCS”.Take your vehicle to any Ford or

Front safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly ag

Safety belt precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injury, mak

Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until

Vehicle sensitive modeThis is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movements and locking in response to

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl

Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could re

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war

If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2 minutesh

Reasons given... Consider...“Belts are uncomfortable” We design our safety belts to enhancecomfort. If you are uncomfortable -try different positions

Traction Controly or AdvanceTracy active (if equipped):Illuminates when the Traction Controly is active, refer to the Drivingchapter for more informat

Do not sit on top of a buckled safety belt to avoid the BeltMinder chime. Sitting on the safety belt will increase the risk ofinjury in an accident. T

3. For the seating position being disabled, buckle then unbuckle thesafety belt 9 times, ending in the unbuckled state. (Step 3 must becompleted withi

vehicles involved in a collision be replaced. However, if the collision wasminor and a qualified technician finds that the belts do not show damageand

“supplemental restraint” means the air bags are intended as asupplement to the safety belts. Air bags alone cannot protect as well asair bags plus saf

Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause thoseobjects to be propelled by the

A difficulty with the system is indicated by one or more of the following:• The readiness light (same lightfor front and side air bag system)will eith

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burn

• diagnostic module.• and the electrical wiring which connects the components.The diagnostic module monitors its own internal circuits and thesuppleme

When the front passenger seat isoccupied and the sensing systemhas turned off the passenger’sfrontal air bag, the 9passenger airbagoff9 or 9pass airba

turns sideways, sits forward, leans forward or sideways, or puts one orboth feet up, the chance of injury during a crash is greatly increased.Sitting

Low washer fluid: Illuminates when the windshield washer fluid is low.• Without Message Center• With Message CenterDoor ajar: Illuminates when the ign

How does the side air bag system work?The side air bag system consists ofthe following:• An inflatable nylon bag (air bag)with a gas generator conceal

If the side air bag hasdeployed, the air bag willnot function again. The sideair bag system (including theseat) must be inspected andserviced by a qua

To reduce risk of injury, do not obstruct or place objects in thedeployment path of the inflatable Safety Canopyy.How does the Safety CanopyYsystem wo

The Safety Canopyy system is designed to activate when the vehiclesustains lateral deceleration sufficient to cause the side crash sensor toclose an e

Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.Alwa

Booster seats should be used until you can answer YES to ALL of thesequestions:• Can the child sit all the way backagainst the vehicle seat back withk

Both can be used in any vehicle in a seating position equipped withlap/shoulder belts if your child is over 40 lbs.The shoulder belt should cross the

When installing a child safety seat:• Review and follow the informationpresented in the Air BagSupplemental Restraint Systemsection in this chapter.•

Installing child safety seats with combination lap and shoulderbeltsAir bags can kill or injure a child in a child seat. NEVER place arear-facing chil

Bulb warning: Illuminates when one of the exterior front turn lamps orrear brake/turn/tail lamps bulb has burned out.• Without Message Center• With Me

3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat.

The tether anchors in your vehicleare in the positions shown:The front passenger seat with power adjustment does not have atether anchor. The two teth

2. Route the child safety seat tetherstrap over the back of the seat. Ifthe head restraint is adjustable,route the tether strap under thehead restrain

If the tether strap is clippedincorrectly (as shown) thechild safety seat may not beretained properly in the event of acollision.5. Rotate the tether

Rear seating positionsFollow steps 1–7 as described above for the following available seats:• 2nd row bucket• 2nd row bench• 3rd row benchFor addition

Attaching safety seats with LATCH (Lower Anchors and Tethers forChildren) attachments for child seat anchorsNew child safety seats have two rigid or w

The lower anchors for child seatinstallation are located at the rearsection of the rear seat between thecushion and seat back.Follow the child seat ma

STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo

Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,

GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera

• Turn the key to 4 (ON) withoutturning the key to 5 (START).Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to i

1. Turn the key to 5 (START)without pressing the acceleratorpedal and release as soon as theengine starts. The key will return to4 (ON).2. When the en

BRAKESOccasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-o

maximizes the amount of brake booster assist, helping the driver toachieve maximum braking pressure. Once a panic brake application isdetected, the sy

and/or when performing emergency maneuvers. In an emergencylane-change, the driver will experience better overall vehicle traction,and have better con

are allowed to spin. If your vehicle seems to lose engine power whiledriving in deep sand or very deep snow, switching off the AdvanceTracystability e

STEERINGTo prevent damage to the power steering system:• Never hold the steering wheel at its furthest turning points (until itstops) for more than a

When the key is in the 3 (OFF) position, the automatictransmission shift lever can be moved from the P (Park) positionwithout the brake pedal depresse

Understanding the gearshift positions of the 4–speed automatictransaxleP (Park)This position locks the transaxle and prevents the front wheels fromtur

1 (First)• Transaxle operates in first gear only.• Provides maximum engine braking.• Allows upshifts by moving gearshift lever.• Will not downshift in

Odometer: Registers the total kilometers (miles) of the vehicle.• Without Message CenterTo switch the display from Metric toEnglish, press and hold th

To help avoid personal injury, always use caution when in R(Reverse) and when using the RSS.This system is not designed to prevent contact with small

The RSS is automatically enabledwhen the gear selector is placed inR (Reverse) and the ignition is ON.The park aid disable switch allowsthe driver to

your vehicle’s weight ratings, with or without a trailer, from the vehicle’sSafety Certification Label and Tire Label:Base Curb Weight – is the weight

GVW (Gross Vehicle Weight) – is the Vehicle Curb Weight + cargo +passengers.GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the

GCWR (Gross Combined Weight Rating) – is the maximum allowableweight of the vehicle and the loaded trailer – including all cargo andpassengers – that

TRAILER TOWINGYour vehicle is capable either of towing Class I trailers or up to Class IItrailers when equipped with the optional trailer tow package.

Vehicle towing capability/Trailerhitch requirementTrailerModel/EngineGCWR -kg (lbs)Hitch typerequiredTrailerWeight range- kg (lbs)Tongue loadVan, 3.9L

Safety chainsAlways connect the trailer’s safety chains to the hook retainers on thehitch. To connect the trailer’s safety chains, cross the chains un

• To eliminate excessive shifting, use a lower gear. This will also assistin transmission cooling. (For additional information, refer to theUnderstand

All Front Wheel Drive (FWD) vehicles:It is not recommended to tow front wheel drive vehicles with the frontdrive wheels on the ground. It is recommend

Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe

GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program

Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will

This switch is located behind theservice panel on the right side ofthe cargo area.To reset the switch:1. Turn the ignition OFF.2. Check the fuel syste

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 Relay Accessory delay relay 12 Relay Acces

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description12 5A Brake-Shift Interlock (BSI) Runfeed, Climate control system Runfeed13

Always disconnect the battery before servicing high currentfuses.Always replace the cover to the power distribution box beforereconnecting the battery

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription8 40A** Anti-lock Brake System (ABS) #2(coil power)9 30A** Power liftgate10 30A** SJB

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription43 15A* Engine #2 (Cooling fan relays,Injectors, PCM, MAF sensor, IAC,Ignition coil,

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription62 30A* SJB #3 – Right cornering/auxiliarylamps, Right low beam, Left frontpark/turn

Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 16Entertainment Systems 19AM/FM stereo 19AM/FM stereo with CD 21AM/FM stereo wi

AM/FM STEREO SYSTEM (IF EQUIPPED)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various settings.2. Audi

CHANGING A FLAT TIREIf you get a flat tire while driving:• do not brake heavily.• gradually decrease the vehicle’s speed.• hold the steering wheel fir

• use tire chains• drive through an automatic car wash, because of the vehicle’s reducedground clearance• try to repair the temporary spare tire or re

Removing the spare tireTo remove the spare tire:1. Open the liftgate and open theplastic cover from the carpeting oncargo floor to expose the hex nut.

4. Remove the primary retainer from the center of the tire. Unlock thesecondary (locking) retainer by rotating the top portion one-quarter turnand rem

• Secondary lock in locked positionNote: Do not stow the full size tire or any flat tire under the vehicle.Dissimilar spare tire/wheel informationFail

• Wet weather driving capability• All-Wheel Driving Capability (if applicable)• Load Leveling Adjustment (if applicable)When driving with the dissimil

2. Place gearshift lever in P (Park),turn engine off, and block thediagonally opposite wheel.3. Remove the spare tire, jack andlug wrench.4. If equipp

If Ford Accessory Running Boardshave been installed, use the jackadapters supplied with the runningboards as described on the inside ofthe jack storag

13. Remove the jack and fullytighten the lug nuts in the ordershown.14. If equipped with a bolted-onwheel cover, install the centerornament and tighte

Make sure to pass the tie throughone of the “loops” on the secondary(locking) retainer,then around the primary cable. Thisallows the secondary (lockin

3. Seek: Press to access thenext/previous strong station ortrack.4. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, pr

5. Repeat this tightness check procedure when servicing the spare tirepressure (every six months, per Scheduled Maintenance Guide), or atany time that

Preparing your vehicleWhen the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, th

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or

AM/FM STEREO/ SINGLE CD SOUND SYSTEM (IF EQUIPPED)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various

The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedu

from Ford and Lincoln Mercury dealership management, recognized fortheir business leadership qualities.What the Board needsTo have your case reviewed

Making a decisionBoard members review all available information related to eachcomplaint, including oral presentations, and arrive at a fair and impar

In the CAMVAP program, impartial third-party arbitrators conducthearings at mutually convenient times and places in an informalenvironment. These impa

ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro

3. The vehicle is out of service for repair of nonconformities for a total ofmore than 30 calendar days (not necessarily all at one time)In the case o

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

sliding door. If necessary, clean the contacts with Motorcraft Bug andTar Remover (ZC-42) to remove any sealant. Do not use any abrasiveson the contac

• Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all partsthat require cleaning and pressure rinse clean.• Cover the highlighted areas to pr

• Do not use fuel, kerosene, or paint thinner to clean any parts.• Wiper blades can be cleaned with isopropyl (rubbing) alcohol orwindshield washer so

Fade: Press to adjust the audio between the front and rear speakers.Use/ / SEEK .Speed sensitive volume (if equipped): Radio volume automaticallychang

Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing.Do not use chemical solvents or

Motorcraft Vinyl Cleaner (Canada only) (CXC-93)Motorcraft Vinyl Conditioner (Canada only) (CXC-94)Motorcraft Deluxe Leather and Vinyl Cleaner (not ava

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.9L/4.2L V6 engines1. Brake fluid reservoir2. Air filter assembly3. Power distribution box4. Battery5

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

4. Open the hood. Protect yourself from engine heat.5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clea

2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler cap

It is recommended you use the appropriate Motorcraft oil filter (oranother brand meeting Ford specifications) for your engine application.BATTERYYour

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a

10. Fast forward: Press tomanually advance in a CD track.11. Rewind: Press to manuallyreverse in a CD track.12. Memory presets: To set astation: Selec

6. With your foot on the brake pedal and with the A/C on, put thevehicle in D (Drive) and allow the engine to idle for at least one minute.7. Drive th

60%, the engine parts could become damaged or not work properly. A50–50 mixture of coolant and water provides the following:• Freeze protection down t

Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservo

For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when

Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i

swallowed can cause death or permanent injury. If fuel is swallowed,call a physician immediately, even if no symptoms are immediatelyapparent. The tox

• DO NOT use a device that would hold the fuel pump handle in the fillposition.Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1

Your vehicle was not designed to use fuel or fuel additives with metalliccompounds, including manganese-based additives.Repairs to correct the effects

Running out of fuelAvoid running out of fuel because this situation may have an adverseaffect on powertrain components.If you have run out of fuel:• Y

PREMIUM IN-DASH SIX CD SOUND SYSTEM (IF EQUIPPED)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various

The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fue

Driving style — good driving and fuel economy habitsGive consideration to the lists that follow and you may be able to changea number of variables and

• Carrying unnecessary weight may reduce fuel economy (approximately0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried).• Adding cer

If other than Ford, Motorcraft or Ford-authorized parts are used formaintenance replacements or for service of components affectingemission control, s

These temporary malfunctions can be corrected by filling the fuel tankwith good quality fuel and/or properly tightening the fuel cap. After threedrivi

1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gauge indicator will benear the center

1. Drive the vehicle 30 km (20 miles) or until it reaches normal operatingtemperature.2. Park the vehicle on a level surface and engage the parking br

Use of a non-approved automatic transmission fluid may causeinternal transaxle component damage.If necessary, add fluid in 250 mL (1/2 pint) increment

and one-half (1 1/2) times as well on the government course as a tiregraded 100. The relative performance of tires depends upon the actualconditions o

When a tire loses inflation, the lowtire warning system detects thechange and illuminates the low tirewarning indicator light as shown.If the light re

Speed sensitive volume (if equipped): Radio volume automaticallychanges slightly with vehicle speed to compensate for road and windnoise. Press MENU t

Reset with message center:To reset turn the ignition to the ONposition, press the set up button onthe message center until “SYSTEMCHECK” is displayed.

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - km/h (mph)Q 159 km/h (99 mp

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation than those of “P” typetires; t

Information on “T” type tiresT145/80D16 is an example of a tiresize.Note: The temporary tire size foryour vehicle may be different thanthis example.1.

Use the recommended cold inflation pressure for optimum tireperformance and wear. Under-inflation or over-inflation may causeuneven treadwear patterns

6. Visually inspect the tires to make sure there are no nails or otherobjects embedded that could poke a hole in the tire and cause an airleak.7. Chec

• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive (4WD)vehicles (front tires at top of

10. Fast forward: Press tomanually advance in a CD track.11. Rewind: Press to manuallyreverse in a CD track.12. Memory presets: To set astation: Selec

Sometimes irregular tire wear can be corrected by rotating the tires.Note: If your tires show uneven wear ask a qualified technician at aFord or Linco

• Severe abrasion on the sidewallIf your vehicle has a leak in the exhaust system, a road tire or the sparetire may be exposed to hot exhaust temperat

Tire explosions can cause death, personal injury or propertydamage. Do not allow anyone to stand near, directly ahead orbehind the spinning tire.Never

• Install chains securely, verifying that the chains do not touch anywiring, brake lines or fuel lines.• Drive cautiously. If you hear the chains rub

Refer to Vehicle Emissions Control Information (VECI) decal for sparkplug gap information.REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrak

2Add the coolant type originally equipped in your vehicle.3Use of synthetic or synthetic blend motor oil is not mandatory. Engineoil need only meet th

Item Ford part name Ford partnumberFordspecificationLock cylinders Penetrating andLock LubricantMotorcraft XL-1 nonePower steeringfluidMotorcraftMERCO

ENGINE DATAEngine 3.9 L OHV V6 engine 4.2L OHV V6 engineCubic inches 232 256Required fuel 87 octane 87 octaneFiring order 1-4-2-5-3-6 1-4-2-5-3-6Ignit

IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt

Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea

If a slot is not selected within 5 seconds, the radio shall eject the currentdisc. Press and hold for 2 seconds to auto eject all CDs present in thera

Transmission/Transaxle code designationsYou can find a transmission/transaxle code on the vehicle certificationlabel which is located on the door pill

Code Transmission DescriptionElectricH One speed electricD Automatic 5–speed overdrive (5R44E)R Automatic 5–speed overdrive (5R55S)Passenger car appli

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford

LifestyleBike racksCargo organization and managementEngine block heaters and blanketsRear seat entertainment systems - DVDTowing mirrorsTrailer hitche

AAccessory delay ...67AdvanceTrac ...172Air bag supplemental restraintsystem ...141–142

plastic parts ...227washing ...225waxing ...225wheels ...

FFloor mats ...73Fluid capacities ...273Fuel ...244calc

LLampsautolamp system ...44bulb replacementspecifications chart ...51daytime running light ...45headlam

Reverse sensing system ...178Roadside assistance ...189Roof rack ...87SSafety Belt Maintenanc

lubricant specifications ...274Turn signal ...48VVehicle dimensions ...276Vehicle Identification

4. Menu: Press to toggle throughthe following modes:Treble: Press to adjust the treble setting. Use/ / SEEK .Bass: Press to adjust the bass setting. U

Locks and Security 89Keys 89Locks 89Anti-theft system 91Seating and Safety Restraints 104Seating 104Safety restraints 127Air bags 141Child restraints

5. AUX: Press to toggle betweenFES/DVD and AUX modes. If noauxiliary sources are available, NOAUX AUDIO will be displayed. To return to radio mode, pr

16. AM/FM: Press to select AM/FMfrequency band.17. ON/OFF/Volume: Press to turnON/OFF. Turn to increase/decreasevolume.If the volume is set above a ce

AUXILIARY AUDIO CONTROLS (IF EQUIPPED)Your vehicle may be equipped with auxiliary audio controls. This featureallows the front and middle seat passeng

PARENTAL CONTROLSimultaneously press the radiopreset controls 3 and 5 toenable/disable the rear seat audiocontrols as well as the Family Entertainment

CASSETTE/PLAYER CAREDo:• Tighten very loose tapes by inserting a pen or pencil into the hole andturning the hub.• Remove loose labels before inserting

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele

5. A/C: Press to engage/disengage. Uses outside or recirculated air tocool the vehicle. Engages automatically in MAX A/C, Defrost andFloor/Defrost. Th

DUAL ZONE MANUAL HEATING AND AIR CONDITIONING SYSTEMWITH REAR PASSENGER COMPARTMENT CLIMATE CONTROL(IF EQUIPPED)1. Air flow selections: Controlsthe di

with MAX A/C or can be engaged manually in any mode except Defrost.Press to engage/disengage. To reduce humidity inside the vehicle, turnrecirculation

ELECTRONIC AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED)1.Defrost: Distributes outside air through the windshield defrostervents. Can be used to clear ic

Cleaning 225Maintenance and Specifications 231Engine compartment 233Engine oil 234Battery 237Fuel information 244Low tire warning system 257Tire Infor

7. A/C control: Press to turn on and manually control the airconditioning. Press again to disengage. Press AUTO for the system toautomatically control

ELECTRONIC AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS (IF EQUIPPED)1.Defrost: Distributes outside air through the windshield defrostervents. Can b

7. :Distributes air through the windshield defroster vents and thefloor vents. The system will automatically provide outside air to reducewindow foggi

OPERATING TIPSAutomatic fan and air distribution are set primarily by the drivertemperature settings. When the driver and passenger temperaturesetting

TEMPERATURE SENSOR (IF EQUIPPED)Your vehicle may be equipped with atemperature sensor grid. This sensorworks together with the AutomaticTemperature Co

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Note:

To program the auto lamp exit time delay:1. Start with the ignition in OFF and the autolamps selected.2. Deselect the auto lamps.3. Put the ignition i

Flash to passPull toward you slightly to activateand release to deactivate.Battery saverThe battery saver will shut off the exterior lamps and interio

Domelamp ControlThe panel dimmer control also controls the domelamp operation.• Rotate the thumbwheel fully to the right, past detent to activate thed

4. On the wall or screen you willobserve a light pattern with highintensity flat segments at the topedge of the pattern. If the flat edgesare not at t

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

Map lamps (if equipped)The map lamps and controls arelocated on the center overheadconsole. Press the raised portion oneach lens to activate the lamps

Dome lamps (if equipped)The front dome lamp is located overhead between the driver andpassenger seats.The dome lamp will stay on if thepanel dimmer co

Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an

2. Remove the two retainer pins torelease the headlamp assembly andpull headlamp assembly forward toexpose the back of the bulb.3. Disconnect the elec

3. To remove the side marker bulb,turn the bulb socketcounterclockwise, and pull the bulbstraight out of the socket.4. To remove the parking/turnbulb,

Replacing license plate lamp bulbThe license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Changing the wiper blades1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas

ILLUMINATED VISOR MIRROR (IF EQUIPPED)Type ALift the mirror cover to turn on thevisor mirror lamps.Type BLift the mirror cover to turn on thevisor mir

overhead console. When the vehicle is turned off, the electronics displaywill remember the last display state.Outside air temperatureThe temperature c

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury and prevent possibledamage to others, you

3. Press and hold the momentarypush-button for approximately 4seconds, until VAR is displayed,then release it. (Pressing themomentary push-button for

SLIDING DOOR OPERATIONManual door operationIf equipped with a Power Sliding Door (PSD), turn the Power DoorLockout control on the overhead console to

Vehicle operation with the door in the open position is notrecommended. Abrupt vehicle acceleration or deceleration could causethe door to move sudden

• pushing and releasing the right orleft hand second row passengercontrol. The control(s) arelocated on the trim panel in frontof the sliding door.• m

Resetting the PSDThe power sliding door may operate incorrectly or not at all because ofthe following conditions:• a low voltage or dead battery• the

To open the sliding door when thechild safety lock is on:• Unlock the sliding door and openthe door from the outside.• Press the right or left handcon

CLOCK (IF EQUIPPED)Press the right + control to movethe time display forward.Press the left - control to move thetime display backwards.AUXILIARY POWE

• Located next to the second rowseat.• Located on the right trim panel inthe rear cargo area.POWER WINDOWSWhen closing the powerwindows, you should ve

One touch downAllows the driver’s window to openfully without holding the controldown. Press completely down onthe bottom part of the rocker switchand

Do not block the sensor on the backside of the inside rear view mirrorsince this may impair proper mirror performance.Will automatically adjust (darke

SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and

Fold-away mirrorsPull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.POWER ADJUSTABLE FOOT PEDALS (IF EQU

Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas

Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET + controluntil you get to the desiredspeed,

Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal. This willnot erase your vehicle’spreviously set s

CENTER CONSOLE (IF EQUIPPED)Your vehicle may be equipped with a variety of console features. Theseinclude:• Utility compartmentCELL PHONE USEThe use o

3. Use a screwdriver to screw locator post into vehicle carpeting. Exertpressure while turning to pierce the carpeting.When installed properly, the lo

1. Press and hold the two outsidebuttons releasing only when the redlight begins to flash after 20seconds. Do not repeat step one toprogram additional

8. Return to the vehicle and firmly press, hold for two seconds andrelease the HomeLinkt button. Repeat the press/hold/release sequenceagain, and, dep

may also be used at any time. In the event that there are stillprogramming difficulties, contact HomeLinkt at www.homelink.com or1–800–355–3515.Erasin

Selectable featuresResetPress this control to select and reset functions shown in the INFO menuand SETUP menu.Info menuThis control displays the follo

Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental restraint

Average Fuel Economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in 100 km/liters ormiles/gallon.If you calculate

Setup menuPress this control for the followingdisplays:• Language• Units (English/Metric)• System CheckLanguage1. Select this function from theSETUP m

System checkSelecting this function from theSETUP menu causes the messagecenter to cycle through each of thesystems being monitored. For eachof the mo

This acts as a reminder that these warning conditions still exist withinthe vehicle.Driver’s door ajar Warning cannot be resetPassenger door ajarLeft

TRANSMISSION OVERHEATED. Indicates the transmission isoverheating. This warning may appear when towing heavy loads or whendriving in a low gear at a h

CHECK FUEL CAP. Displayed when the fuel filler cap is not properlyinstalled. Check the fuel filler cap for proper installation. Refer to Fuelfiller ca

4. Press and hold the RESETcontrol to display “OIL LIFE SETTO 100%”. Your oil life is now reset.To reset the oil monitoring system to your personalize

DATA ERR. These messages indicate improper operation of the vehiclenetwork communication between electronic modules.• Fuel Computer• Oil life• Chargin

CARGO AREA FEATURESCargo net (if equipped)The cargo pouch net secureslightweight objects in the cargoarea. Attach the net to the anchorsprovided. Do n

To adjust the cross-bar (if equipped) position:1. Loosen the thumbwheel at bothends of the cross-bar (bothcross-bars are adjustable).2. Slide cross-ba

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-

KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w

remote entry keypad (if equipped), or using the lock button on theremote entry transmitter (if equipped).Childproof door locks• When these locks are s

• 3–button remote• 5–button remoteThe remote entry system allows you to:• lock or unlock all vehicle doors and liftgate without a key.• unlock/open a

Opening/closing power sliding doors (if equipped)• 5–button remote• Press this control twice within three seconds to open the powersliding door. The i

To replace the battery:1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIR

To reprogram the remote entrytransmitters:1. Ensure the vehicle is electronically unlocked.2. Put the key in the ignition.3. Turn the key from the 3 (

The panel dimmer control must not be set to the off position for theilluminated entry system to operate.The inside lights will not turn off if:• they

2. Turn the ignition to the 3 (OFF) position, then press the power doorunlock control 3 times.3. Turn the ignition to 4 (ON) position. Completing the

Memory feature (if equipped)The remote entry system allows you to recall the memory seat/side viewmirrors/adjustable pedals feature.Pressto automatica

• open and close the right and left power sliding doors (if equipped).• recall memory seat/side view mirrors/adjustable pedals position Driver1 or Dri