Before drivingIntroduction 2Instrumentation 6Controls and features 19Seating and safety restraints 92Starting and drivingStarting 129Driving 134Roadsi
Safety beltMomentarily illuminates when theignition is turned to the ON positionto remind you to fasten your safetybelts. For more information, refer
Ensure that the second row seat is in the upright position in order toachieve optimum access to the third row.To minimize the risk of personal injury,
2. Before removing the seat, be surethat the detachable anchor tongue isstowed flat into the vehicle floor.3. Use the black plastic clip (locatedjust
Installing the third row seatAlways latch the vehicle seat to the floor, whether the seat isoccupied or empty. If not latched, the seat may cause inju
3rd row tip/stow featureThe 3rd row seat has a tip/stow feature to increase cargo space withoutremoving the seat from the vehicle.To put seat in tip/s
6. Pull down support bar and pushinto floor latch.To return seat to seating position:1. Hold seat and pull support bar from floor latch.2. Rotate supp
It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in these areasare more likely to be se
2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.The front and rear outboard safety restraints in the vehicle arecombinatio
How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt
Lap beltsAdjusting the lap beltThe lap belts should fit snugly and as low as possible around thehips, not around the waist.• 1st row and 3rd row (if e
Front and second row safety belt height adjustmentYour vehicle has safety belt heightadjustments for the driver, frontpassenger and second rowpassenge
High beamsIlluminates when the high beamheadlamps are turned on.SecuriLockY anti-theft systemThis light indicates the anti-theftalarm system is armed.
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignition switchis turned to the ON position...The safety belt wa
The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...9Crashes are ra
One time disableAnytime the safety belt is buckled and then unbuckled during an ignitionON cycle, Belt Minder will be disabled for that ignition cycle
6. Within seven seconds of the safety belt warning light turning off,buckle then unbuckle the safety belt.• This will disable Belt Minder if it is cur
AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Your vehicle is equipped with a crash sensing and diagnostic modulewhich records information about the air
Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.National Highway Traffic Safety
Children and air bagsFor additional important safetyinformation, read all information onsafety restraints in this guide.Children must always be proper
The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burn
The RCM (restraints control module) monitors its own internal circuitsand the supplemental air bag electrical system warning (including theimpact sens
Do not use accessory seat covers. The use of accessory seatcovers may prevent the deployment of the side air bags andincrease the risk of injury in an
Four wheel drive low (if equipped)Momentarily illuminates when theignition is turned to the STARTposition. Illuminates whenfour-wheel drive low is eng
by the collision will be inflated, even if the respective seat is notoccupied. The air bag was designed to inflate between the door paneland occupant
A difficulty with the system is indicated by one or more of the following:• The readiness light (same light as for front air bag system) will eitherfl
properly restrained in the rear seating positions than in the front seatingposition.Children and safety beltsIf the child is the proper size, restrain
SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully fo
Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a seating position which is capableof provid
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a c
Installing child safety seat in the second row center seatingposition with an automatic locking retractor1. Place the child safety seat in the center
4. Before placing the child in the seat, forcibly tilt the seat forward andback to make sure the seat is securely held in place.5. Check to make sure
PREPARING TO START YOUR VEHICLEEngine starting is controlled by the powertrain control system. Thissystem meets all Canadian Interference-Causing Equi
This light comes on when either the COAST/SET or RES/ACCEL controlsare pressed. It turns off when the cruise cancel control is pressed, thebrake is ap
2. Make sure the headlamps and vehicle accessories are off.3. Make sure the parking brake isset.4. Make sure the gearshift is in P(Park).5. Turn the k
Make sure the corresponding lights illuminate briefly. If a light fails toilluminate, have the vehicle serviced.• If the driver’s safety belt is faste
recommended if you live in a region where temperatures reach -23°C(-10°F) or below.For best results, plug the heater in at least three hours before st
Important ventilating informationIf the engine is idling while the vehicle is stopped in an open area forlong periods of time, open the windows at lea
BRAKESYour service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance.Occasional brake noise is normal and o
ABS warning lampABSTheABSwarning lamp in the instrument cluster momentarily illuminateswhen the ignition is turned to the ON position. If the light do
Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th
Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.STEERINGY
Speed sensitive steeringThe steering in your vehicle is speed sensitive. At high speeds, steeringassist will decrease to improve steering feel. At low
The air suspension shut-off switch islocated behind an access panelunderneath the passenger sideinstrument panel.On vehicles equipped withAir Suspensi
GAUGESFuel gaugeDisplays approximately how muchfuel is in the fuel tank (when thekey is in the ON position). The fuelgauge may vary slightly when thev
To avoid injury, never run the engine with one wheel off theground, such as when changing a tire.PREPARING TO DRIVE YOUR VEHICLEUtility vehicles have
AUTOMATIC TRANSMISSION OPERATIONBrake-shift interlockThis vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever fr
Driving with a 4–speed automatic transmissionUnderstanding gearshift positionsTo put your vehicle in gear, start the engine, depress the brake pedal,t
(Overdrive) can be deactivatedby pressing the transmission controlswitch (TCS) on the end of thegearshift lever.The transmission control indicatorligh
higher speeds causes the transmission to shift to a lower gear, and willshift to 1 (Low) after vehicle decelerates to the proper speed.Forced Downshif
CONTROL-TRAC AUTOMATIC FOUR-WHEEL DRIVE SYSTEM(IF EQUIPPED)Your 4x4 features the heavy-duty Control-Trac system which includes acomputer-operated tran
Using the Control-Trac systemShifting from A4WD to 4HMove the 4WD control from A4WDto 4H at any forward speed up to 88km/h (55 mph).At temperatures be
Driving off-road with 4WDYour vehicle is specially equipped for driving on sand, snow, mud andrough terrain and has operating characteristics that are
When driving through water, determine the depth; avoid water higherthan the bottom of the hubs (if possible) and proceed slowly. If theignition system
Automatic transmission may shift frequently while driving up steepgrades. Eliminate frequent shifting by shifting out of(Overdrive) intoD (Drive).Driv
Engine coolant temperature gaugeIndicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal ar
• Payload: Combined maximum allowable weight of cargo, passengersand optional equipment. The payload equals the gross vehicle weightrating minus base
limitations. Replacement tires with a higher limit than the originals donot increase the GVWR and GAWR limitations.The Certification Label, found on t
2. Weigh your vehicle as you customarily operate the vehicle withoutcargo. To obtain correct weights, try taking your vehicle to a shippingcompany or
and turn lamps, back up lamps, battery charge, electric brakes (when acustomer provided controller is installed) and ground. The kit includedwith your
Do not exceed the maximum loads listed on the Safety ComplianceCertification label. For load specification terms found on the label, referto Vehicle l
4. Attach the trailer to the vehicle and adjust the hitch equalizers so thatthe front bumper height is within 0–13 mm (0.5 in) of the referencepoint.
1 814 kg (4 000 lb.) trailer weight and 181 kg (400 lb.) tongue weightcapability.Use a frame-mounted weight distributing hitch for trailers over 1814
Improper removal/installation of the driveshaft can causetransmission fluid loss, damage to the driveshaft and internaltransmission components.4WD veh
Disconnect the wiring to the trailer before backing the trailer into thewater. Reconnect the wiring to the trailer after the trailer is removedfrom th
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford offers acomplimentary roadside assistance program. This program
TachometerIndicates the engine speed inrevolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the e
Roadside coverage beyond basic warrantyIn the United States, you may purchase additional roadside assistancecoverage beyond this period through the Fo
The fuel pump shut-off switch islocated in the passenger’s foot well,by the kick panel.Use the following procedure to reset the fuel pump shut-off swi
Always replace a fuse with one that has the specified amperagerating. Using a fuse with a higher amperage rating can causesevere wire damage and could
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger CompartmentFuse Panel Description1 25A Audio2 5A Overhead Trip Computer, Elec
Fuse/RelayLocationFuse AmpRatingPassenger CompartmentFuse Panel Description6 5A Cluster, Overhead Trip Computer, Compass,Brake Shift Interlock Solenoi
Fuse/RelayLocationFuse AmpRatingPassenger CompartmentFuse Panel Description21 15A Starter Relay, Fuse 20, Transmission RangeSwitch22 10A Air Bag Modul
Power distribution boxThe power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protec
The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description1 20A * Power Point2 30A* Powertrain Con
Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description104 30A** 4x4 Shift Motor & Clutch105 40A** Climate Control Front Blower106 — No
Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description401 — Not Used501 — Powertrain Control Module Diode502 — A/C Clutch Diode503 — Not U
TRIP COMPUTERThe trip computer tells you about the condition of your vehicle througha constant monitor of vehicle systems. You may select display feat
Removing the jack handle1. Open the hood.2. Unsnap the end of the handle that is retained by the clip on the top ofthe windshield washer bottle.3. Uns
Stowing the spare tire1. Lay the tire on the ground with the outboard side facing up.2. Install the retainer through thewheel center and slide the whe
1. Park on a level surface, activatehazard flashers and set the parkingbrake.2. Place gearshift lever in P (Park)and turn engine OFF.3. Block the diag
7. Turn OFF the air suspensionswitch (if equipped).8. Position the jack according to thefollowing guides and turn the jackhandle clockwise until the w
• Front (4x4)• RearTo lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engin
12. Remove the jack and fullytighten the lug nuts in the ordershown.13. Put flat tire, jack and lug wrenchaway. Make sure the jack is fastenedso it do
Connecting the jumper cables1. Connect the positive (+) booster cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
The fuel range function will flash for 5 seconds when you haveapproximately the following distance you can drive before the fuel tankis empty:• 80 km
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center.It
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
Do not start your engine with the air cleaner removed and donot remove it while the engine is running.OPENING THE HOOD1. Inside the vehicle, pull the
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.6L V8 and 5.4L V8 engines1. Battery2. Automatic transmission fluid dipstick3. Engine oil filler cap4
3. Set the parking brake and ensure the gearshift is securely latched in P(Park).4. Open the hood. Protect yourself from engine heat.5. Locate and car
Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t
Ford production and aftermarket (Motorcraft) oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedtha
Do not let the fluid level in the reservoir for the master cylinderfall below the MIN mark. If master cylinder runs dry, this maycause the brakes to f
Canada, Motorcraft CXC-10), or an equivalent premium engine coolantthat meets Ford specification ESE-M97B44-A.A 50/50 mixture of distilled water and F
If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the reservoir islow or
HEADLAMP CONTROLRotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlam
Do not put engine coolant in the windshield washer fluidreservoir. If engine coolant is sprayed onto the windshield, itcould make it difficult to see
Recycled engine coolantFord Motor Company recommends the use of a recycled engine coolantproduced by Ford-approved processes.Not all coolant recycling
• decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damag
Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to a service facility as soon as possible to minimize enginedamage.W
4. Check the fluid level in thereservoir. It should be between theMIN and MAX lines. Do not addfluid if the level is in this range.5. If the fluid is
5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. Ifnecessary, refer to Identifying components in the engine compartmentin this
The transmission fluid should be inthis range if at ambient temperature(10°C-35°C [50°F-95°F]).High fluid levelFluid levels above the safe rangemay re
intervals. If the original universal joints are replaced with universal jointsequipped with grease fittings, lubrication will also be necessary.BATTER
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a
7. Drive the vehicle to complete the relearning process.• The vehicle may need to be driven 16 km (10 miles) or more torelearn the idle and fuel trim
The following warning may be required by California law:CALIFORNIA Proposition 65 WarningEngine exhaust, some if its constituents, and certain vehicle
Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Light (DRL) Systemdoes not activate your tail lamps
Changing the air filter element1. Loosen the clamp that securesthe air inlet tube to the engine airfilter cover and disconnect the tubefrom the cover.
WINDSHIELD WIPER BLADESCheck the wiper blades at least twice a year or when they seem lesseffective. Substances such as tree sap and some hot wax trea
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
• Four tire rotationReplacing the tiresReplace the tires when the wearband is visible through the tiretreads.When replacing full size tires, never mix
Do not replace your tires with “high performance” tires or largersize tires.Failure to follow these precautions may adversely affect thehandling of th
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsDo not overfill the fuel tank. The pressure in an overfilled tankmay cause leak
• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kindcan lead to eye and respiratory tract irritation. In severe cases,excessive or p
Choosing the right fuelUse only UNLEADED FUEL. The use of leaded fuel is prohibited by lawand could damage your vehicle.Do not use fuel containing met
Cleaner airFord approves the use of reformulated “cleaner-burning” gasolines toimprove air quality. These gasolines may contain oxygenates up to 10%et
• To turn autolamps off, rotate the control clockwise to OFF.• Foglamps are not controlled by the autolamps. In order to turn on thefoglamps, you must
The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stopsbefore completely rem
The amount of empty reserve varies and should not be reliedupon to increase driving range. When refueling your vehicle afterthe fuel gauge indicates e
Driving style — good driving and fuel economy habitsGive consideration to the lists that follow and you may be able to changea number of variables and
• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in your vehicle Sche
converter and other emission control components continue to workproperly:• Use only the specified fuel listed.• Avoid running out of fuel.• Do not tur
Readiness for Inspection/Maintenance (I/M) testingIn some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics sys
Replacing headlamp bulbs1. Make sure that the headlamp control is in the OFF position.2. Open the hood.3. At the back of the headlamp, pullclips rearw
11. Straighten alignment pins, making them parallel with the outer edgesof the attachment standoff.12. Carefully insert the headlampassembly into the
3. Carefully pry the lamp assembly away from the vehicle to expose thebulb sockets.4. Rotate the bulb socket counterclockwise and remove from lampasse
2. Carefully pull the lamp assemblyaway from the vehicle to access thebulbs.3. Remove the bulb socket byturning counterclockwise and acareful pull.4.
4WD CONTROL (IF EQUIPPED)This control operates the 4WD.Refer to the Driving chapter formore information.REVERSE SENSING SYSTEM (IF EQUIPPED)The revers
Function Number of bulbs Trade numberHeadlamps 2 9007Front park/turn lamps 2 3157NAK (amber)Front sidemarker 2 194NA (amber)Foglamps 2 899Dome/map lam
AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident the alignment of yo
Use only carnauba or synthetic-based waxes. Use a cleaning fluid with aclean cloth to remove any bugs before waxing your vehicle. Use tarremover to re
• Never apply anything to the drive belt (including belt dressing).• Cover the highlighted areas to prevent water damage when cleaningthe engine.• Nev
hot wax treatments used by commercial car washes. Clean the outside ofthe windshield or rear window with a non-abrasive cleaner such as FordUltra-Clea
the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available fromyour Ford Dealer. This mild cleaner and special pad, cleans the leatherand maintain
MOTORCRAFT PART NUMBERSComponent 4.6L V8 engine 5.4L V8 engineAir filter element FA-1634 FA-1634Battery BTX-65-650 BTX-65-650Fuel filter FG-986B FG-98
Fluid Ford PartNameApplication CapacityTransmissionfluid1MotorcraftMERCONtVATF4R70W 13.1L(13.9 quarts)2MotorcraftMERCONt ATF4R100 (4x2) 15.0L(15.9 qua
Fluid Ford PartNameApplication Capacity5.4L V8 enginewith 2 rowradiator and auxrear heat26.4L(27.9 quarts)Front axlelubricantMotorcraft SAE75W-90Premi
amount of transmission fluid and fluid level should be set by theindication on the dipstick’s normal operating range.3Use Ford Premium Engine Coolant
The reverse sensing system detectsobstacles within approximately 1.8meters (5.9 ft.) of the rear bumperwith a decreased coverage area atthe outer corn
ItemFord partnameFord partnumberFordspecificationDriveshaft, slipspline, doubleCardan jointcenter ballPremium LongLife GreaseXG-1-C orXG-1-K orXG-1-C
ItemFord partnameFord partnumberFordspecificationRear axle2Motorcraft SAE75W-140 HighPerformanceSynthetic RearAxle LubeF1TZ-19580-B WSL-M2C192-AFront
ENGINE DATAEngine 4.6L V8 engine 5.4L V8 engineCubic inches 281 330Required fuel 87 octane 87 octaneFiring order 1-3-7-2-6-5-4-8 1-3-7-2-6-5-4-8Spark
41352Capacities and specifications233
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification Label be affixedt
Ford Extended Service PlanYou can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. For
If you have questions or concerns, or are unsatisfied with the service youare receiving, follow these steps:1. Contact your Sales Representative or Se
If you own a Lincoln vehicle and are away from home when your vehicleneeds service, or if you need more help than the dealership couldprovide, after f
dispute handling procedure is not required prior to enforcing statecreated rights or other rights which are independent of the Magnuson-Moss Warranty
Eligibility may differ according to state law. For example, see the uniquebrochures for California, West Virginia, Georgia and Wisconsinpurchasers/les
AUXILIARY POWER POINTThe auxiliary power point is locatedon the instrument panel.Do not plug optional electricalaccessories into the cigarette lighter
• the names (if known) of all the people you contacted at thedealership(s)• a description of the action you expect to resolve your concernYou will rec
You may also contact the North American Customer Assistance Center at1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 orby writing
The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emission control system and may causeengine knock
Ford Deluxe Leather and Vinyl Cleaner (not available in Canada)Motorcraft Vinyl Cleaner (Canada only)Ford Extra Strength Tar and Road Oil Remover* (no
Comfort and convenienceCabin air filterCargo netsCargo organizersCargo traysDash trim (wood grain)Engine block heatersTire stepTravel equipmentAuto he
Carpet floor matsCleaners, waxes and polishesFlat splash guardsFront end covers (full and sport)Hood deflectorsInside mirror with compass displayInsid
cause the engine to stumble or stall. In addition, such systems may bedamaged or their performance may be affected by operating yourvehicle. (Citizens
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould im
Accessory delay ...78Air bag supplementalrestraint system ...114,118and child safety seats ...116descrip
washing ...221waxing ...221wheels ...222wiper bl
USING YOUR AUDIO SYSTEMPremium AM/FM Stereo/Cassette (CD Changer Compatible)Premium AM/FM Stereo/Cassette (CD Changer Compatible)SCANVOLPUSH ONREW1FF2
Floor mats ...81Fluid capacities ...226Foglamps ...20Four-Whee
lighting uppanel and interior ...20location of components ...8Jump-starting your vehicle ...175Keyless entry systemaut
fluid, specifications ...229,232Preparing todrive your vehicle ...140Radio ...25Rela
Water, Driving through ...149Windowspower ...77rear wiper/washer ...68Windshield was
254
Item InformationRequired fuel Unleaded fuel only - 87 octaneFuel tank capacity-4x2 without airsuspension98.6L (26.0 gallons)Fuel tank capacity-4x4 veh
Some transmission fluids may be labeled as dual usage, such asMERCONt and MERCONt V. These dual usage fluids are not to be usedin an automatic transmi
Volume/power controlPress the control to turn the audiosystem on or off.Turn the control to raise or lowervolume.If the volume is set above a certain
• to increase volumecompensation• to decrease or shut off thevolume compensationAM/FM selectThe AM/FM select control works inradio, tape and CD modes
• Press to select the next disc in the CD changer. Hold the controlto fast-forward through the remaining discs.Seek functionThe seek function control
Scan function in tape modePress the SCAN control to hear a short sampling of all selections on thetape. (The tape scans in a forward direction. At the
BREAKING-IN YOUR VEHICLEThere are no particular breaking-in rules for your vehicle. During thefirst 1 600 km (1 000 miles) of driving, vary speeds fre
If there are less than six strong stations available on the frequency band,the remaining memory preset controls will all store the last strongstation
Tape/CD select• To begin tape play (with a tapeloaded into the audio system)while in the radio or CD mode,press the TAPE control. Press thebutton duri
Eject functionPress the control to stop and eject atape.DolbyTnoise reductionDolbyt noise reduction operatesonly in tape mode. Dolbyt noisereduction r
identification or program type from RDS-equipped FM radio stations.The Federal Communications Commission (FCC) and the Canadian Radioand Telecommunica
• Info• Jazz• Oldies• R&B• Religious• Rock• Soft• Top 40Show• With RDS activated, press theRDS control until SHOW isdisplayed.• Use the SEL contro
Use the SEL control to select thedesired signal mode (the selectedmode will appear in the display).The following signal modes can beselected:• JAZZ CL
Premium AM/FM Stereo/Single CD RadioVolume/power controlPress the control to turn the audiosystem on or off.Turn the control to raise or lowervolume.I
The recommended level for speed sensitive volume is from level 1through level 3. Level 0 turns the speed sensitive volume off and level 7is the maximu
Tune adjust for CD changer• Press to select the previousdisc in the CD changer. (Play willbegin on the first track of thedisc unless the CD changer is
Scan function in CD modePress the SCAN control to hear a short sampling of all selections on theCD (The CD scans in a forward direction, wrapping back
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
Bass adjustThe bass adjust control allows youto increase or decrease the audiosystem’s bass output.Treble adjustThe treble adjust control allows youto
RewindThe rewind control works in CDmode.• In CD mode, pressing the REWcontrol for less than threeseconds results in slow rewind.Pressing the control
Shuffle feature (if equipped)The shuffle feature operates in CDchanger mode and plays all trackson the current disc in random order.The shuffle featur
• Use the SEL control to select theprogram type. With the featureon, use the SEEK or SCANcontrol to find the desiredprogram type from the followingsel
Setting the clockPress the RDS control until SELECTHOUR or SELECT MINS isdisplayed.Use the SEL control to manually setthe time.• Pressto increasehours
Adjusting the volumePress the + control to increasevolume.Press the - control to decreasevolume.From the rear seat controls, volume control can be set
Mode selectPush the MODE control to togglebetween AM, FM1, FM2, tape, CD orCD changer (if equipped).Memory preset controlPush the MEMORY controlsucces
CD changer (if equipped)Your CD changer is located in the center console.Slide the door to access the CDchanger magazine.Pressto eject the magazine.1.
2. Insert one disc into each CD trayof the magazine (up to 6 discs).Ensure that the label side is facingup.If you pull too hard on the discholder, the
Radio power must be turned on to play the CDs in the changer. Themagazine may be stored in the glove compartment when not being used.The CD magazine m
Vehicle Symbol GlossaryChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Engine OilEngine CoolantEngine CoolantTemperat
Cleaning cassette player (if equipped)Clean the tape player head with a cassette cleaning cartridge after 10 to12 hours of play in order to maintain t
• Station overload. Weak signals are sometimes captured by strongersignals when you pass a broadcast tower. A stronger signal maytemporarily overtake
The air conditioning compressor will operate in all modes except PANELand FLOOR. However, the air conditioning will only function if theoutside temper
sent to the windshield defroster ducts. If the temperature is about10°C (50°F) or higher, the air conditioner will automaticallydehumidify the air to
• If your vehicle has been parked with the windows closed during hotweather, the air conditioner will do a much faster job of cooling if youdrive for
Turning the EATC offPress OFF. The OutsideTemperature function will continueto operate until the ignition isturned off.Automatic operationPress AUTOMA
To control the temperature, selectany temperature between 18°C(65°F) and 29°C (85°F) by pressingthe blue (cooler) or red (warmer)buttons.For continuou
The display will show to indicatemanual fan operation.To return to automatic fan operation, press AUTOMATIC.Manual override controlsThe override contr
• FLOOR-Allows for maximum heating by distributing outside airthrough the floor ducts. However, the air cannot be cooled below theoutside temperature
The outside temperature reading is most accurate when the vehicle ismoving. Higher readings may be obtained when the vehicle is notmoving. The reading
DLHLHEFCHBRAKEPRND2CRUISEDOORAJARSELECT/RESETTHEFTFUEL DOOR0MPHRPMX1000km/h2040608000204060ONOFFRESSETACCELCOASTDPEDALSHeadlampcontrol(pg. 19)Turn sig
Auxiliary A/C-heater controls (if equipped)The auxiliary A/C-heater feature provides increased capacity to quicklyheat or cool the vehicle. Besides th
or located in the overhead console.In order for the auxiliary A/C-heatercontrols to function, the driver’sauxiliary A/C-heater control must beset to R
Turn the temperature control to thedesired temperature.You can get warm or cool airthrough either the overheadregisters or floor vent by turning theau
TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.SPEED CONTROLTo turn speed control on• Press
To turn speed control off• Press OFF or• Turn off the vehicle ignition.Once speed control is switched off, the previously programmed set speedwill be
To set a higher set speed• Press and hold SET/SET ACC/SET ACCEL. Release the controlwhen the desired vehicle speed isreached or• Press and release SET
To disengage speed control• Depress the brake pedal.Disengaging the speed control willnot erase the previouslyprogrammed set speed.Pressing OFF will e
TILT STEERINGPull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredpo
Push (tap) the end of the stalkbriefly for a single swipe (no wash).Push and hold for three swipes withwash. Push and hold for a longerwash (up to ten
Deactivating overdrivePress the Transmission ControlSwitch (TCS) located on the end ofthe gearshift lever. TheTransmission Control Indicator Light(TCI
4HA4WD4LHI LO COOL WARMOFFPANELFLOORDEFFLR& DEFPANEL &FLOORA/CMAXA/CSCANVOLPUSH ONREW1FF2SIDE 1.23COMP5SHUFF6AUTOTUNESEEKSELBA
Installing a garage door opener (if equipped)The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers:• Pla
Without trip computer• Press and release the rear portion of the moon roof control to open.• Press and hold (as desired) the front portion of the moon
Most geographic areas (zones) have a magnetic north compass point thatvaries slightly from the northerly direction on maps. This variation is fourdegr
Without trip computer1. Press and hold the SELECTcontrol until VAR appears in thedisplay, then release. The displayshould show the current zonenumber.
Without trip computer1. Press and hold the SELECTcontrol until CAL appears in thedisplay (approximately eightseconds) and release.2. Drive the vehicle
Press the portion of the VENT control to open the power rearquarter windows.Press the portion of the VENT control to close the power rearquarter windo
Rear dome lampThe dome lamp lights when:• any door is opened.• the instrument panel dimmerswitch is held up until thecourtesy lamps come on.• any of t
POWER WINDOWSPress and hold the rocker switches to open and close windows.• Press the top portion of therocker switch to close.• Press the bottom port
Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controlsexcept for the driver’s press
POWER SIDE VIEW MIRRORSThe ignition can be in any position to adjust the power side view mirrors.To adjust your mirrors:1. Select L to adjust the left
WARNING LIGHTS AND CHIMESLow fuelIlluminates as an early reminder of alow fuel condition indicated on thefuel gauge (refer to Fuel Gauge inthis chapte
Signal mirrors (if equipped)When the turn signal is activated,the outer portion of the appropriatemirror housing will blink red.This provides an addit
Rear center console features (if equipped)The rear center console incorporates the following features:• utility compartment• cupholdersPOSITIVE RETENT
Make sure that the liftgate door and/or window are closed toprevent exhaust fumes from being drawn into the vehicle. Thiswill also prevent passengers
Spare coded keys can be purchased from your dealership andprogrammed to your anti-theft system. Refer to Programming spareSecuriLocky keys for more in
2. Turn ignition to OFF and remove the first coded key from the ignition.3. Within five seconds of turning the ignition to OFF, insert the secondprevi
Unlocking the doorsPress this control to unlock thedriver door. The interior lamps andrunning board lamps (if equipped)will illuminate.The memory mirr
Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment.Replaci
Replacing lost transmittersIf a remote transmitter has been lostand you would like to remove itfrom the vehicle’s memory, or youwould like to purchase
Illuminated entryThe illuminated entry system will turn on the interior lights when theremote transmitter unlock control is pressed.The illuminated en
1. Turn the ignition key to ON.2. Press the power door unlock control three times.3. Turn the ignition key from ON to OFF.4. Press the power door unlo
What you should do if the Service Engine Soon light illuminatesLight turns on solid:This means that the OBD II system has detected a malfunction.Tempo
5. Turn the ignition back to ON. The horn will chirp.6. Press the unlock control, then press the lock control. The horn willchirp once if autolock was
2. Press 1/2 control within fiveseconds of step one.3. Press 7/8 control and 9/0 controlat the same time within five secondsof step 2.The system will
SEATINGAdjustable head restraints (if equipped)Your vehicle’s seats may be equipped with head restraints which arevertically adjustable. The purpose o
Always drive and ride with your seatback upright and the lapbelt snug and low across the hips.Reclining the seatback can reduce the effectiveness of t
60/40 split bench seat (if equipped)• Lift the release bar to move theseat forward or backward. Ensurethe seat is relatched into place.• Pull the seat
Always drive and ride with your seatback upright and the lapbelt snug and low across the hips.Reclining the seatback can reduce the effectiveness of t
Memory seats (if equipped)This system allows automaticpositioning of the driver seat,outside rearview mirrors, andadjustable pedals to threeprogrammab
REAR SEATSHead restraintsYour vehicle’s seats may be equipped with head restraints which arevertically adjustable. The purpose of these head restraint
3. Press the green control on theseatback to release the closeoutpanel. Rotate the panel to closeoutthe space in the floor.4. Once the second row seat
Reclining the seatbackLocate the lever at the bottom ofthe seatback that reads “FOLDFLAT OR RECLINE”. Pull the leverupwards to recline the seatback.Th
Commentaires sur ces manuels