Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 18Entertainment Systems 21How to get going 21AM/FM stereo with CD 25AM/FM stereo
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
Slide on rod featureRotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage.Note: To stow the visor back intoth
Installing a garage door opener (if equipped)The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers:• Pla
WARNING: Use only soft cups in the cupholder. Hard objectscan injure you in a collision.Rear center console features (if equipped)The rear center cons
To prevent the fuse from being blown, do not use the power point(s)over the vehicle capacity of 12 VDC/180W. If the power point or cigarlighter socket
Press and pull the window switchesto open and close windows.• Press down (to the first detent)and hold the switch to open.• Pull up (to the first dete
Bounce-back (driver’s window only)When an obstacle has been detected in the window opening as thewindow is moving upward, the window will automaticall
Automatic dimming interior rear view mirror (if equipped)Your vehicle may be equipped with an interior rear view mirror whichhas an auto-dimming funct
To adjust your mirrors:1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror.2. Mo
POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is
Enable/disable:To enable/disable the power running board feature, refer to the Messagecenter in this chapter.• When this feature is disabled (OFF), th
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
SPEED CONTROL (IF EQUIPPED)With speed control set, you can maintain a set speed without keepingyour foot on the accelerator pedal.WARNING: Do not use
Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed.Increasing spee
Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal. This will not erase your vehicle’s previouslyset
In CD mode (if equipped):• PressSEEK to select the next selection on the CD/USBor press and hold to forward or reverse through the CD/USB.In DVD mode
Press to activate phone mode or answer a phone call. Press andhold to end call or exit phone mode.Pressto scroll through various menus and selections.
To open the moon roof: Press andrelease the SLIDE control, the moonroof will open automatically. Pressthe switch again to stop the moonroof.To close t
WARNING: When programming your HomeLink威 WirelessControl System to a garage door or gate, be sure that people andobjects are out of the way to prevent
Visor mount1. Position the end of your hand-held transmitter 1–3 inches (2–8 cm)away from the HomeLink威 button you wish to program while keeping thein
HomeLink威 should now activate your rolling code equipped device. Toprogram additional HomeLink威 buttons begin with Step 1 in this section.For question
Operating the HomeLink姞 Wireless Control SystemConsole mountVisor mountTo operate, simply press and release the appropriate HomeLink威 button.Activatio
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
Erasing HomeLink姞 buttonsConsole mountVisor mountTo erase the three programmed buttons (individual buttons cannot beerased):• Press and hold the two o
STANDARD MESSAGE CENTER (IF EQUIPPED)With the ignition in the on position,the message center, located on yourinstrument cluster, displaysimportant veh
DTE is calculated using a running average fuel economy, which is basedon your recent driving history of 500 miles (800 km). This value is notthe same
• Autounlock• Park Aid (if equipped)• Trailer sway control• Oil Life Reset and Start Value• Compass display• Compass zone adjustment• Compass calibrat
The sequence of the system check report and how it appears in themessage center is as follows:1. OIL LIFE2. CHARGING SYSTEM3. WASHER FLUID4. DOOR AJAR
AutolampThis feature keeps your headlights on for up to three minutes after theignition is switched off.1. To change the time delay of theautolamp fea
Reverse Sensing System (Park Aid) (if equipped)This feature sounds a warning tone to warn the driver of obstacles nearthe rear bumper, and functions o
3. Once “OIL LIFE SET TO 100%” isdisplayed, release, press and holdthe SELECT/RESET control switchfor more than two seconds tochange the Oil Life Star
Compass zone adjustment using mirror mounted compass resetbutton (if equipped)1. Determine which magnetic zoneyou are in for your geographiclocation b
2. Locate the reset button on the compass sensor mounted on the baseof mirror.3. To calibrate, press and hold the reset button on the compass modulefo
Service engine soon: The serviceengine soon indicator lightilluminates when the ignition is firstturned to the on position to checkthe bulb and to ind
2. Press and hold the SELECT/RESET stem to enter the setup menuoption. Press and release the SELECT/RESET stem to scroll through themessage center unt
Warning display StatusDoor ajar Warning cannot be resetFuel level low Warning returns after 10 minutesPark brake engagedCheck brake systemCheck park a
CHECK FUEL FILL INLET (if equipped) — Displayed when the fuelfill inlet may not be properly closed. Refer to Easy Fuel™ “no cap” fuelsystem in the Mai
WASHER FLUID LEVEL LOW — Indicates the washer fluid reservoiris less than one quarter full. Check the washer fluid level. Refer toWindshield washer fl
OPTIONAL MESSAGE CENTER (IF EQUIPPED)With the ignition in the on position,the message center, located on yourinstrument cluster, displaysimportant veh
Info menuThe Info menu items are shown onthe top two lines of the messagecenter. Press the INFO control todisplay the following:• Trip odometer (Trip
Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in miles/gallon or liters/km.If you calculate you
Fuel UsedSelecting this function from theINFO menu. “FUEL USED XXX.XGAL” will display the fuel used sincelast reset. The information displayedwill be
• Easy Entry/Exit Seat (if equipped)• Park Aid (if equipped)• Trailer sway control• Compass display• Compass zone adjustment• Compass calibration adju
3. WASHER FLUID4. DOOR AJAR5. EXTERIOR LAMP6. BRAKE FLUID LEVEL7. PARK BRAKE8. FUEL LEVEL AND DISTANCE TO EMPTYUnits (English/Metric)1. Select this fu
• Optional instrument clusterBrake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when the
1. To change the delay time of theautolamp feature, select thisfunction from the SETUP MENU.2. Press the RESET control to selectthe new Autolamp delay
Power Running Boards (if equipped)This feature automatically deploys the side running boards for easyentry/exit from the vehicle or for cleaning. Refe
1. To disable/enable the reversesensing system feature with thevehicle in P (Park), select thisfunction from the SETUP MENU orput the vehicle in R (Re
Compass zone adjustment (if equipped)1. Determine your magnetic zone byreferring to the zone map.2. Turn ignition to the on position.3. Start the engi
Compass calibration adjustmentPerform compass calibration in an open area free from steel structuresand high voltage lines. For optimum calibration, t
2. Press and hold the RESETcontrol for more than two seconds.Oil life is set to 100% and “OILCHANGE SET TO 100%” isdisplayed.Note: To change oil life
Warning display StatusDoor ajar Warning cannot be resetFuel level low Warning returns after 10 minutesPark brake engagedService RSC nowCheck brake sys
CHECK FUEL FILL INLET (if equipped) — Displayed when the fuelfill inlet may not be properly closed. Refer to Easy Fuel™ “no cap” fuelsystem in the Mai
WASHER FLUID LEVEL LOW — Indicates the washer fluid reservoiris less than one quarter full. Check the washer fluid level. Refer toWindshield washer fl
POSITIVE RETENTION FLOOR MATWARNING: Do not install additional floor mats on top of thefactory installed floor mats as they may interfere with theacce
Safety belt: Reminds you to fastenyour safety belt. A Belt-Minder威chime will also sound to remind youto fasten your safety belt. Refer tothe Seating a
Cargo management systemThe cargo management system consists of storage compartments locatedin the floor of the rear cargo area.7 passenger stowage:1.
• To open the liftgate window,press the control on the remoteentry transmitter or, with theliftgate unlocked, push thecontrol button on the right side
LUGGAGE RACKYour vehicle is equipped with a roof rack for transporting items on theexterior of the vehicle.The maximum recommended load tobe carried o
Ford Motor Company recommends loading the roof rack only whenequipped with (optional) crossbars, to avoid unintended damage to theroof panel.WARNING:
KEYSOne key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency.Your keys are programmed to your v
Deactivating/activating autolockYour vehicle comes with the autolock feature enabled. There are fourmethods to enable/disable this feature:• Through y
Keyless entry keypad procedure1. Turn the ignition to the off position.2. Close all doors, the liftgate and liftgate window.3. Enter 5–digit entry cod
Power door unlock/lock procedureYou must complete Steps 1-5 within 30 seconds or the procedure willhave to be repeated. If the procedure needs to be r
Power door lock/unlock inhibit feature (if equipped)If the key is not in the ignition, all doors are closed, and the vehicle hasbeen locked using the
CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the
WARNING: Never remove the coolant reservoir cap while theengine is running or hot.Low tire pressure warning:Illuminates when your tire pressureis low.
The remote entry system allows youto lock or unlock all vehicle doorsand liftgate, open the liftgatewindow without a key and activatethe panic alarm.T
Locking the doors/liftgate1. Press and release to lock all the doors and liftgate. The lamps willflash. Note: If any door, the liftgate or the liftgat
2. Press the SET control on thelower-center portion of theinstrument panel.3. Within five seconds, press onecontrol on the remote transmitterand then
2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery.Note: Please refer to localreg
3. Turn the key from the 1 (off)position to 3 (on).4. Cycle eight times rapidly (within10 seconds) between the 1 (off)position and 3 (on). Note: Theei
SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• open the liftgate
• If you program a code to a position that already contains a set code,the previously-set code will be erased.Erasing personal code1. Enter the factor
Your vehicle comes with two coded keys; additional coded keys may bepurchased from your authorized dealer. The authorized dealer canprogram your spare
Automatic disarmingSwitching the ignition to the on position with a coded key disarms thevehicle.• The theft indicator will illuminate for three secon
2. Turn the ignition from the 1 (off)position to the 3 (on) position. Keepthe ignition in the 3 (on) positionfor at least three seconds, but nomore th
O/D off: Illuminates when theoverdrive function of thetransmission has been turned off;refer to the Driving chapter.AdvanceTrac威: Flashes when theAdva
SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o
To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o
To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous
WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting the front manual seat (if eq
Using the manual lumbar support (if equipped)For more lumbar support, turn thelumbar support control toward thefront of vehicle.For less lumbar suppor
WARNING: To reduce the risk of possible serious injury: Do nothang objects off seat back or stow objects in the seatback mappocket (if equipped) when
Press the control to recline theseatback forward or rearward.Using the power lumbar support (if equipped)The power lumbar control is located on the ou
A position can be recalled:• in any gearshift position if the ignition is not in the on position.• only in P (Park) or N (Neutral) if the ignition is
Deactivating/activating the easy access/easy out featureThe easy entry/exit feature can be turned off or on through the vehiclemessage center (if equi
Note: Do not do the following:• Place heavy objects on the seat• Operate the seat heater if water or any other liquid is spilled on theseat. Allow the
Turn signal: Illuminates when theleft or right turn signal or thehazard lights are turned on. If theindicators stay on or flash faster, check for a bu
If needed, when installing some high back child restraints, the headrestraints of the second row seating positions can be removed. Insert athin pointe
1. Lower the head restraints bypulling on the strap.2. Locate the recline handle situatedon the side of the seat cushion bythe door.3. Pull up on the
2. Lift up on the head restraint untilit locks into its original position.To return the seat to the upright position (E-Z entry equippedseats):1. Lift
WARNING: Before returning the seatback to its originalposition, make sure that cargo or any objects are not trappedbehind the seatback. After returnin
Returning to the upright position from full lowered load floorpositionThe seatback cannot be returned to the upright position until the seat isreturne
WARNING: Always return the seat to the fully latched positionbefore operating the vehicle.Returning the seat to the upright positionNote: To return th
WARNING: Before returning the seatback to its originalposition, make sure that cargo or any objects are not trappedbehind the seatback. After returnin
3rd row folding seat (if equipped)Before folding the third row seats,fold the head restraints down bypulling on the strap located underthe restraint.P
The control buttons are located onthe driver-side rear quarter trimpanel (accessible from the liftgatearea).Push the bottom portion of thecontrol butt
WARNING: Before returning the seatback to its originalposition, make sure that cargo or any objects are not trappedbehind the seatback. After returnin
Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,
The fact that the pretensioners or airbags did not activate for both frontseat occupants in a collision does not mean that something is wrong withthe
WARNING: Air bags can kill or injure a child in a child seat.NEVER place a rear-facing child seat in front of an active airbag. If you must use a forw
Determining if the Personal Safety System姞 is operationalThe Personal Safety System威 uses a warning light in the instrumentcluster or a back-up tone t
WARNING: It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision, people riding inthese areas are more likely
WARNING: BELT AND RETRACTOR ASSEMBLY MUST BEREPLACED if the safety belt assembly automatic lockingretractor feature or any other safety belt function
All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have threetypes of
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
Safety belt pretensionerYour vehicle is equipped with safety belt pretensioners at the driver andright front passenger seating positions.The safety be
Second row comfort guideThe second row outboardlap/shoulder belt is equipped with abelt comfort guide. This guide isattached to the quarter trim panel
Safety belt extension assemblyIf the safety belt is too short when fully extended, there is an 8 inch(20 cm) safety belt extension assembly that can b
Locks and Security 154Keys 154Locks 154Anti-theft system 160Seating and Safety Restraints 170Seating 170Safety restraints 189Airbags 204Child restrain
Trip odometer: Registers the miles (kilometers) of individual journeys.• Standard instrument clusterPress the SELECT/RESET controlonce to switch from
The Belt-Minder威 feature uses information from the front passengersensing system to determine if a front seat passenger is present andtherefore potent
If... Then...The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately1 minute while the vehicle istraveling at least 3 mph(5 km
Reasons given... Consider...“Traffic is light” Nearly 1 of 2 deaths occur insingle-vehicle crashes, many whenno other vehicles are around.“Belts wrink
Deactivating/activating the Belt-Minder姞 featureThe driver and front passenger Belt-Minder威 aredeactivated/activated independently. When deactivating/
4. Within approximately seven seconds of the light turning off, bucklethen unbuckle the safety belt.• This will disable the Belt-Minder威 feature for t
WARNING: All occupants of the vehicle, including the driver,should always properly wear their safety belts, even when an airbag supplemental restraint
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
• one or more impact and safing sensors.• a readiness light and tone.• diagnostic module.• and the electrical wiring which connects the components.• F
The front passenger sensing system will turn off the passenger seat sideairbag if:• the seat is empty and safety belt is unbuckled.The front passenger
AUDIO SYSTEMSQuick start — How to get goingWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly
• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LampPasseng
ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase,
WARNING: To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a chi
WARNING: Any alteration/modification to the front passengerseat may affect the performance of the front passenger sensingsystem.Determining if the sys
WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. Contact your authorize
The side airbags are fitted on the outboard side of the seatbacks of thefront seats. In certain lateral collisions, the airbag on the side affected by
Safety Canopy姞 systemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a deploying
How does the Safety Canopy姞 system work?The design and development of theSafety Canopy威 system includedrecommended testing proceduresthat were develop
The Safety Canopy威 system is designed to activate when the vehiclesustains lateral deceleration sufficient to cause the side crash sensor toclose an e
Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref
Listening to satellite radio (if equipped)1. If the audio system is turned off,press VOL-PUSH to turn the radioon. Turn VOL-PUSH to adjust thevolume.N
SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme
Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb
Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe
WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli
If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestr
Installing child safety seats with combination lap and shoulderbeltsIf needed, when installing some high back child restraints, the headrestraints of
• Keep the buckle release button pointing up and away from the safetyseat, with the tongue between the child seat and the release button,to help preve
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up
however the safety belt can still be used to attach the child seat. Forforward-facing child seats, the top tether strap must also be attached tothe pr
For a single CD system, if a discis not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the
The LATCH anchors for child seatinstallation are located at the rearsection of the second row seatbetween the cushion and seatback.The LATCH anchors a
WARNING: Depending on where you secure a child restraint,and depending on the child restraint design, you may blockaccess to certain safety belt buckl
Attaching child safety seats with tether strapsMany forward-facing child safety seats include a tether strap whichextends from the back of the child s
Perform the following steps to install a child safety seat with tetheranchors:1. Route the tether strap under the head restraint and between the headr
3. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theeven
When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the
Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
Move a child to a different seating location if the shoulder belt does notstay positioned on the shoulder during use.Follow all instructions provided
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
While in folder mode, pressFOLDER to access the nextfolder on MP3 discs, if available.Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inth
Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary
• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and
TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen
TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary
INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air
The cold inflation pressure should never be set lower than therecommended pressure on the Safety Compliance Certification Label orTire Label.When weat
TIRE CAREInspecting your tiresPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones, nails or glass that
WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressur
WARNING: Only use replacement tires and wheels that are thesame size, load index, speed rating and type (such as P-metricversus LT-metric or all-seaso
It is recommended that the two front tires or two rear tires generally bereplaced as a pair.The tire pressure sensors mounted in the wheels (originall
AM/FM Single CD/MP3 satellite compatible sound system(if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and
Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your
Note: If your tires show uneven wear ask an authorized dealer to checkfor and correct any wheel misalignment, tire imbalance or mechanicalproblem invo
4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new
8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n
13. Maximum Permissible Inflation Pressure: Indicates the tiremanufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw
Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti
When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.
In CATEGORY MODE, press / to scroll through the list ofavailable SIRIUS channel Categories (Pop, Rock, News, etc.). Refer toCategory Mode under Menu f
Low TirePressureWarning LightPossiblecauseCustomer Action RequiredFlashing WarningLightSpare tire inuseYour temporary spare tire is inuse. Repair the
SNOW TIRES AND CABLESWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. The use ofnon-recommende
your vehicle, familiarize yourself with the following terms for determiningyour vehicle’s weight ratings, with or without a trailer, from the vehicle’
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or performance, e
WARNING: Do not use replacement tires with lower loadcarrying capacities than the original tires because they maylower the vehicle’s GVWR and GAWR lim
• A final example for your vehicle with 1,400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the
2. Weigh your vehicle without cargo. To obtain correct weights, take yourvehicle to a shipping company or an inspection station for trucks.3. Subtract
4x2GCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.0L SOHC Class
• DELETE SONG: Press OK to delete a song from the system’smemory. Press/ to cycle through the saved songs. When thesong appears in the display that yo
4X4 and AWDGCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.6L* C
Class III Trailer Hitch Safety ChainLoops can be used as recoveryhooks.Do not attach safety chains to the bumper.Trailer brakesElectric brakes and man
Driving while you towWhen towing a trailer:• To ensure proper “break-in” of powertrain components, do not trailertow during the first 1,000 miles (1,6
• If you will be towing a trailer frequently in hot weather, hillyconditions, at GCWR, or any combination of these factors, considerrefilling your rea
RECREATIONAL TOWINGFollow these guidelines if you have a need for recreational (RV) towing.An example of recreational towing would be towing your vehi
STARTINGPositions of the ignition1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accesso
WARNING: If you smell exhaust fumes inside your vehicle, haveyour dealer inspect your vehicle immediately. Do not drive if yousmell exhaust fumes.Impo
• Make sure the gearshift is in P(Park).3. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminate. See
Starting the engine1. Turn the key to 3 (on) withoutturning the key to 4 (start). If thereis difficulty in turning the key,rotate the steering wheel u
ENGINE BLOCK HEATER (IF EQUIPPED)An engine block heater warms the engine coolant which aids in startingand allows the heater/defroster system to respo
To activate, press MENU repeatedly until RBDS (ON/OFF) appears inthe display. Use / / SEEK to toggle RBDS ON/OFF. WhenRBDS is OFF, you will not be abl
• Be sure that areas where the vehicle is parked are clean and clear ofall combustibles such as petroleum products, dust, rags, paper andsimilar items
brake pedal pulsation may be observed during ABS braking and thebrake pedal may suddenly travel a little farther as soon as ABS braking isdone and nor
The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned on) until theparking brake is released.
ADVANCETRAC姞 WITH ROLL STABILITY CONTROL™ (RSC姞)STABILITY ENHANCEMENT SYSTEMWARNING: Vehicle modifications involving braking system,aftermarket roof r
The AdvanceTrac威 with RSC威 system provides the following stabilityenhancement features for certain driving situations:• Traction Control (TCS), which
• If the driving condition is severe and your foot is not on the brake, thebrake pedal may move as the systems applies higher brake forces. Youmay als
Certain adverse driving maneuvers may activate the Electronic StabilityControl system, which include but are not limited to:• Taking a turn too fast•
with RSC威 system can be restored by pressing the AdvanceTrac威 withRSC威⬙Off⬙ button again or by turning off and restarting the engine.If you switch off
During Trailer Sway Control events, the icon in the instrumentcluster will flash momentarily. The message center will also display:TRAILER SWAY REDUCE
If the power steering system breaks down (or if the engine is turnedoff), you can steer the vehicle manually, but it takes more effort. If thesteering
TRACK/FOLDER MODE: Available only on MP3 discs in CD mode.In track mode, pressSEEK, SEEK to scroll through all tracks onthe discIn folder mode, pressS
AUTOMATIC TRANSMISSION OPERATIONBrake-shift interlockThis vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever fr
Driving with a 5–speed automatic transmission (if equipped)This vehicle is equipped with an Adaptive Transmission Control Strategy.This Adaptive Trans
N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D
2 (Second)Use 2 (Second) to start-up on slippery roads or to provide additionalengine braking on downgrades.1 (First)• Provides maximum engine braking
P (Park)This position locks the transmissionand prevents the rear wheels fromturning.To put your vehicle in gear:• Press the brake pedal• Start the en
D (Drive) without OverdriveOverdrive can be deactivated bypressing the transmission controlswitch on the side of the shift lever.• This position allow
• Allows upshifts by moving gearshift lever.• Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds
WARNING: Certain add-on devices such as large trailer hitches,bike or surfboard racks and any device that may block thenormal detection zone of the re
Audible WarningsDistance to Object WarningSpeed above 2.5 mph (4 km/h)up to 1.6 feet (.5 meters) Solid1.6 feet (.5 meters) to 3.1 feet (1 meter) Fast
FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED)WARNING: For important information regarding safe operationof this type of vehicle, see Preparing to dri
Customer Assistance 337Reporting safety defects (U.S. only) 343Reporting safety defects (Canada only) 344Cleaning 345Maintenance and Specifications 35
6. / (Play/Pause): Thiscontrol is operational in CD andDVD mode (if equipped). When aCD or DVD is playing in the FES system, press this control to pla
4X4 LOW (4WD Low) - Provides locked four-wheel drive power whenextra power at reduced speeds is required. This mode is notrecommended for use on dry p
Normal operation (4.6L engine vehicles only)During normal operation the AWD system is in AWD AUTO mode (AWDLOCKED will illuminate in the message cente
You should either know the terrain or examine maps of the area beforedriving. Map out your route before driving in the area. To maintainsteering and b
If your vehicle gets stuckIf your vehicle gets stuck in mud or snow it may be rocked out byshifting between forward and reverse gears, stopping betwee
WARNING: Vehicles with a higher center of gravity such asutility and four-wheel drive vehicles handle differently thanvehicles with a lower center of
WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your author
If the transmission, transfer case or front axle are submerged in water,their fluids should be checked and changed, if necessary.Driving through deep
Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;
Never drive with chains on the front tires of AWD or 4WD vehicleswithout also putting them on the rear tires. This could cause the rear toslide and sw
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
PRESET # SAVED appears in the display. You can save up to 18 stations,six in AM, six in FM1 and FM2.In satellite radio mode (if equipped), there are 1
• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co
FUEL PUMP SHUT-OFF SWITCHFUELRESETThe fuel pump shut-off switch is a device intended to stop the electricfuel pump when your vehicle has been involved
FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth
Passenger compartment fuse panelThe fuse panel is located below theinstrument panel on the driver’sside.To remove a fuse use the fuse puller tool prov
Fuse/RelayLocationFuse AmpRatingProtected Circuits5 5A Moon roof, Door lock switchillumination, Rearview mirror withmicrophone6 20A Liftglass release
Fuse/RelayLocationFuse AmpRatingProtected Circuits22 15A Brake switch, Bi-color stop lamps,CHMSL, All turn lamps23 15A Interior lamps, Puddle lamps,Ba
Power distribution boxThe power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protec
The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 50A** BATT 2 (SJB)2 50A** BATT 3 (SJB)3 50A** BATT 1 (
Fuse/RelayLocationFuse AmpRatingProtected Circuits14 30A** Memory seats (DSM)40A** Non-memory seats15 40A** Rear defrost, Heated mirrors16 40A** Front
Fuse/RelayLocationFuse AmpRatingProtected Circuits40 15A* Fan clutch, PCV valve, AC clutchrelay, GCC fan41 15A* SDARS, DVD, SYNC42 15A* Redundant brak
16. CD: Press to enter CD/MP3mode. If a CD/MP3 is already loadedinto the system, CD/MP3 play willbegin where it ended last. If no CD is loaded, NO DIS
CHANGING THE TIRESIf you get a flat tire while driving:• do not brake heavily.• gradually decrease the vehicle’s speed.• hold the steering wheel firml
A dissimilar spare tire/wheel is defined as a spare tire and/or wheel thatis different in brand, size or appearance from the road tires and wheelsand
The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following:• Handling, stability and braking performance• Comfort and
Location of the spare tire and toolsThe spare tire and tools for your vehicle are stowed in the followinglocations:Tool LocationSpare tire Under the v
Removing the spare tireDo not use an impact wrench on the winch drive nut. This willdamage the spare tire winch.1. Open the cover from the carpeting o
3. Turn the wrenchcounterclockwise until the tire islowered to the ground and the cablehas slack. When turning the wrench,make sure that it does not s
1. Block the wheel that is diagonallyopposite of the flat tire using thewheel chock provided with yourvehicle.2. Use the tip of the lug wrench toremov
5. Position the jack according to theillustrated guides and turn the jackhandle clockwise until the tire is amaximum of 1 inch (25 mm) off theground.N
9. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torquespecifications later in this chapterfor the proper lu
2. Stow the wheel ornament (if removed) in a safe location in the vehicle(such as the glove box or jack stowage compartment) so it will notbecome dama
Accessory delay: Your vehicle is equipped with accessory delay. Withthis feature, the window switches, radio and moon roof (if equipped)may be used fo
RUNNING OUT OF FUELIf you have run out of fuel and need to refill the vehicle with a portablefuel container, see Running out of fuel in the Maintenanc
3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake onboth vehicles
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to the g
WARNING: Do not connect the end of the second cable to thenegative (-) terminal of the battery to be jumped. A spark maycause an explosion of the gase
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGNote: Turn off the power running boards (if equipped) prior topreparing the vehicle for towing. Refer to Running boards in the DriverCon
On 4x4/AWD vehicles, it is required that your vehicle be towed with awheel lift and dollies or flatbed equipment with all the wheels off theground.If
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized
In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph
In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext
• SAVE SONG: Press OK to save the currently playing song’s title inthe system’s memory. (If you try to save something other than a song,CANT SAVE will
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is
• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent qu
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
4.6L V8 ENGINEPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authorized
• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32-A),available from your au
AUTOSET: Press MENU until the display reads AUTOSET. Autosetallows you to set the strongest local radio stations without losing youroriginal manually
If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows:1. Wipe up spilled liqui
LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• For routine cleaning, wipe the surface wit
Motorcraft Detail Wash (ZC-3-A)Motorcraft Dusting Cloth (ZC-24)Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20)Motorcraft Engine Shampoo (C
SERVICE RECOMMENDATIONS• Use the scheduled maintenance information to track routineservice.• Use only recommended fuels, lubricants, fluids and servic
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.0L SOHC V6 engine1. Engine oil filler cap2. Engine oil dipstick (out of view)3. Brake fluid reservoi
4.6L V8 engine1. Air filter assembly2. Engine oil filler cap3. Engine oil dipstick4. Brake fluid reservoir5. Power distribution box6. Battery7. Power
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas
4. To attach the new wiper to thewiper arm, align the cross pin andkeyway (denoted with the arrows)and firmly press the wiper bladeinto the wiper arm
The default setting is off; increasing your vehicle speed will not changethe volume level.Adjust 1–7: Increasing this setting from 1 (lowest setting)
• 4.6L V8 engine6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil level is between the lower and upper holes, t
• 4.6L V8 engine• Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized dealer.7. Put the
Engine Oil Recommendations4.0L V6 EngineLook for this certificationtrademark.Use SAE 5W-30 engine oilOnly use oils “Certified For Gasoline Engines” by
4.6L 3V V8 EngineLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by the AmericanPetroleum
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If
WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
• 4.0L V6 engine• 4.6L V8 engine• The engine coolant should be at the FULL COLD level or within theCOLD FILL RANGE as listed on the engine coolant res
Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. When the engine is cool, add the mixtu
For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when
If your vehicle is equipped with a Family Entertainment System (FES)please refer to the Family Entertainment DVD system later in thischapter.If your v
Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage.Recycle
• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i
Oil overheat can be triggered in severe driving conditions, such astowing heavy loads over mountainous terrain in extreme hottemperatures. As oil temp
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsWARNING: Do not overfill the fuel tank. The pressure in anoverfilled tank may c
• Fuels can also be harmful if absorbed through the skin. If fuel issplashed on the skin and/or clothing, promptly remove contaminatedclothing and was
Use the following guidelines to avoid electrostatic charge build-up whenfilling an ungrounded fuel container:• Place approved fuel container on the gr
immediately. It may take several driving cycles for the Check Fuel FillInlet lamp or Check Fuel Fill Inlet message to turn off. A driving cycleconsist
Do not be concerned if your engine sometimes knocks lightly. However, ifit knocks heavily under most driving conditions while you are using fuelwith t
• The service engine soon indicator may come on. For moreinformation on the service engine soon indicator, refer to Warninglights and chimes in the In
ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform
Note: In track mode, all tracks on the current disc will shuffle inrandom order. In MP3 folder mode, the system will randomly play alltracks within th
Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers).2. Each time you fill the tan
• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between the top gears occurs. Unnecessaryshifting of this type co
EPA fuel economy estimatesEvery new vehicle should have a window sticker containing EPA fueleconomy estimates. Contact your authorized dealer if the w
WARNING: Exhaust leaks may result in entry of harmful andpotentially lethal fumes into the passenger compartment.Do not make any unauthorized changes
If the service engine soon indicator remains on, have your vehicleserviced at the first available opportunity. Although some malfunctionsdetected by t
POWER STEERING FLUIDCheck the power steering fluid. Refer to scheduled maintenanceinformation.1. Start the engine and let it rununtil it reaches norma
TRANSMISSION FLUIDChecking automatic transmission fluidThe automatic transmission does not have an underhood transmissionfluid dipstick.Refer to your
3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening.Use only fluid that meets Ford specifications
Changing the air filter element• 4.0L Engine• 4.6L Engine1. Release the clamps that secure the air filter housing cover.2. Carefully separate the two
MOTORCRAFT PART NUMBERSComponent 4.0L SOHC V6 engine 4.6L 3V V8 engineAir filter element FA-1695 FA-1780Fuel filter FG-1083 FG-1083Battery BXT-65-650
Press and hold to hear a brief sampling of the next channels. Press againto stop.In CATEGORY MODE, press SCAN to hear a brief sampling of thechannels
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord Part Name orequivalentFord Part Number / FordSpecificationBrake fluidBetween MINand
Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationEngine coolant 4.0Lengine withoutauxiliary climatecontrol12.2 quarts(11.5L
Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationEngine oil 4.6Lengine6.0 quarts(5.7L)Motorcraft SAE5W-20 PremiumSynthetic
Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationTransfer case fluid(AWD)1.3 quarts(1.25L)Motorcraft TransferCase FluidXL–1
ENGINE DATAEngine 4.0L SOHC V6engine4.6L 3V V8engineCubic inches 245 281Required fuel 87 octane 87 octaneFiring order 1-4-2-5-3-6 1-3-7-2-6-5-4-8Ignit
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
Roof rail cross barsTrailer hitch drawbars, wiring harnesses and accessoriesTripTunes™ Advanced portable audio connectionPeace of mindMobile-Ease™ han
AAccessory delay ...105AdvanceTrac ...283Air cleaner filter ...387–389Air conditioning ...
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
18. (CD eject): To eject a discfrom the system, press . Selectthe correct slot number usingmemory presets 1–6. When ready, the system will eject the d
Cleaning your vehicleengine compartment ...347instrument panel ...349interior ...350plas
lubrication specifications ...390refill capacities ...390service points ...355–356starting after a collision .
Hood ...354How to get going ...21IIgnition ...275, 394Illumina
Oil (see Engine oil) ...359PParking brake ...281Parts (see Motorcraft parts) ...389Passenger OccupantClassifi
SecuriLock passive anti-theftsystem ...166Setting the clockAM/FM single CD ...27AM/FM/In-dash 6
Water, Driving through ...308Windows ...161power ...103rear wiper/washe
Required equipment:1. Any portable music player designed to be used with headphones2. An audio extension cable with stereo male 1/8 in. (3.5 mm)connec
5. For safety reasons, connecting or adjusting the settings on yourportable music player should not be attempted while the vehicle ismoving. Also, the
• Station overload: When you pass a broadcast tower, a stronger signalmay overtake a weaker one and play while the weak station frequencyis displayed.
CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m
Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The
Your vehicle may be equipped with a Family Entertainment System(FES) which allows you to listen to audio CDs, MP3 discs, watch DVDsand to plug in and
Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti
Press the power button to turn thesystem off. The indicator light willturn off indicating the system is off.Note: The audio from the DVD system will p
3. The disc will begin to play andthe ‘MP3 Audio Disc’ screen willdisplay and allow you to access theCOMPRESSION, SHUFFLE, SCANand FOLDER MODE feature
from the auxiliary source, the screen will remain black. If the videosource is set to DVD-AUX, the display will automatically turn on if avideo signal
1. Press theheadphone/speaker/ buttonon the DVD player or press the 2and 4 memory presets on the radio at the same time.A green light will illuminate
To adjust display brightness:To decrease/increase the brightnesslevel on the display screen, pressthe brightness control on the DVDsystem. A display w
2. / (Stop/Eject): Pressonce to stop and press a secondtimetoejectadiscfromtheDVDsystem.3.(Reverse): Press andrelease for the previous chapter ortrack
10. Volume: When in single playmode, press to increase ( )ordecrease ( ) the volume over allspeakers. When in Dual Play, pressto increase () or decrea
16. Cursor /Brightness controls:Use the cursor controls to makevarious selections when in anymenu. When not in a menu, and inDVD mode, press/ to adjus
4. RETURN: Press to return to the previous menu screen.5. ANGLE(DVD dependent): Press to select the angle to view the scene.6. Channel A/B: Press to s
19. MENU: Press to access the DVD disc menu for selections. PressMENU again when in the DVD disc menu to access the system set-upmenu.20. SUBTITLE (DV
Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance
HeadphonesWireless headphonesWARNING: The driver should never use the headphones whiledriving the vehicle. Using headphones may prevent the driverfrom
To install the batteries, remove the screw at the bottom of the cover.Then, lightly press down on top and slide the cover off.When replacing the batte
To operate the headphones:• Press POWER on the ear piece to turn on the headphones. A redindicator light will illuminate indicating the headphones are
Wired headphonesWARNING: Do not leave children unattended in the vehicle anddo not let children operate the system while unsupervised. Ifwired headpho
Single Play: Single play consists of all occupants in the vehicle listeningto the same playing media over the front and rear speakers. When theDVD sys
Press the Headphone Control buttonA to change the audio source forChannel A.Press MEDIA to change the audiosource for Channel A. Thisinformation will
Press the Headphone Control buttonA to change the audio source forChannel A.Press MEDIA to change the audiosource for Channel A. Thisinformation will
Menu modePress MENU once on the DVD system to access the DVD disc menu ifavailable.Press MENU twice to access the DVD set-up menu and the followingfea
You can select from: WIDE, LETTERBOX or PAN SCAN. Once you havemade your selection, press ENTERto confirm. The LCD screen displaywill immediately chan
Once you have made your selection,press ENTER to confirm. This isdisc dependent.Audio CDsTo play audio CDs on your DVD system:1. Ensure that the vehic
Event Data RecordingOther modules in your vehicle — event data recorders — arecapable of collecting and storing data during a crash or nearcrash event
4. The folder, track and elapsedtime will appear in the status bar.The screen will list the Artist, Title,Album and File Name.COMP (Compression):Compr
CD, MP3 and CD player care• Handle discs by their edges only. Never touch the playing surface.• Do not expose discs to direct sunlight or heat sources
Playing a DVD1. Ensure that the vehicle is on or the ignition is in accessory mode.2. Ensure that the navigation system is on.3. Insert a DVD label-si
Frame by frame1. With a DVD playing, press pause.2. Press the right cursor button. TheDVD will advance one frame. Eachpress of the right cursor button
The B headphone jack (5) is locatedon the right side of the DVD system.Plug in wired headphones (notincluded) here.Note: The B headphones can onlyacce
There are three levels of control ofthe FES buttons. The states areFULL (enabled), LOCAL orLOCKED (disabled). To change the level of control, press th
rights owners. Use of this copyright protection technology must beauthorized by Macrovision Corporation, and is intended for home andother limited vie
WARNING: The driver should not attempt to operate anyfunction of the DVD system while the vehicle is in motion. Givefull attention to driving and to t
Care and service of the DVD playerEnvironmental extremesDVD players which are subjected to harsh environmental conditions maybe damaged or perform at
Cleaning DVD and CD discsInspect all discs for contamination before playing. If necessary, cleandiscs only with an approved DVD and CD cleaner and wip
Notice to owners of pickup trucks and utility type vehiclesWARNING: Utility vehicles have a significantly higher rolloverrate than other types of vehi
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield.• To improve the A/C cool down when the vehicle interior issign
DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM(IF EQUIPPED)1. A/C control: Manually turns A/Con or off.2. Recirculation control: Coolsthe vehicle mo
5. DUAL (Single/dual electrictemperature control): Allows thedriver to have full control of thecabin temperature settings (single zone) or allows the
15. Fan Speed: Manually increasesor decreases the fan speed.16. EXT: Displays the outside airtemperature. It will remaindisplayed until the EXT contro
To allow side window defogging and demisting while warming up thevehicle cabin:1. Select.2. Select A/C.3. Set the temperature control to maintain comf
FLOOR CONSOLE CLIMATE CONTROLSControls the direction of the airflowto the rear of the vehicle.•directs air flow primarilythrough the console panelregi
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola
Fog lamp controlThe fog lamps can be turned ononly when the headlamp control isin the, or position andthe high beams are not turned on.Pull headlamp c
Flash to passPull the lever toward you toactivate. Release the lever todeactivate.PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument pa
Cell phone useThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri
To adjust the headlamps:1. Park your vehicle on a level surface about 25 feet (7.6 meters) awayfrom a vertical plain surface (3). Check your headlamp
TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSDome/reading lampsThe dome lam
Cargo/reading lampsThe dome portion of the lamp orthe center light can be turned onwhen the panel dimmer control isrotated fully up or when a door iso
Function Number of bulbs Trade numberHeadlamp low & highbeam2H13Front park/turn lamp 2 3457 NAK (amber)Side park/turn lamp 2 194Upper rear tail la
Replacing headlamp bulbsDo not touch the glass of a halogen bulb.1. Turn off the headlamps and openthe hood.2. Remove three screws from theheadlamp as
Replacing front parking lamp/turn signal/sidemarker bulbs1. Turn off the headlamps and openthe hood.2. Remove three screws from theheadlamp assembly a
4. Rotate the bulb socketcounterclockwise and remove itfrom the lamp assembly.5. Pull the bulb straight out of thesocket.Reverse steps to reinstall bu
Replacing high-mount brakelamp bulb1. Remove the two screws and lampassembly away from the vehicle.2. Remove the bulb holder from thelamp assembly by
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
O (off) — Rear wiper and washer off.For rear wash cycle, rotate (and hold as desired) the rear wiper/washercontrol to eitherposition.From either posit
Commentaires sur ces manuels