Ford SUPER DUTY F-SERIES 6C34-19A268-BA Manuel d'utilisateur télécharger pdf (Page 25)

23F-SERIES (March, 2005)

STATEMENTS OF CONFORMITY

HOLES (12 PLACES)

OF BRACKET

3/16 INCH

BLIND RIVET

(12 REQ’ D)

87.0

[3.42]

78.0

[3.07]

48.0

[1.89]

48.0

[1.89]

78.0

[3.07]

48.0

[1.89]

105.7

[4.16]

67.5

[2.66]

48.0

[1.89]

81.0

[3.19]

616.0

[2.42]

POINT

SECTION U

VIEW

48.0

[1.89]

81.0

[3.19]

REFER TO CALIFORNI

FUEL VAPOR RECOVERY

REQUIREMENT

SCREWS (3 REQ’D)

TORQUE 1.7-2.8

NEWTON METERS

[15-25 IN. LB.]

[1.89]

SUB

TO BACK

OF CA

L OF FILL PIPE ASY.

AND BRACKET

FRONT OF

VEHICLE

PROTECTIVE SLEEVES ARE

REQUIRED ON BOTH FILL AND

VENT HOSE WHERE PASSIN G

ER FRAME.

SCREWS (3 REQ’D)

RQUE 1.7-2.8

NEWTON METERS

[15-25 IN. LB.]

RECIRCULATION

HOS

OUTBOARD SURFAC E

OF FRAME RAI

FILL HOSE

90º FITTING - CONNECT TO

QUICK CONNECTION ON VAPOR LIN

#4 CR

OSSMEMBER

TOP OF FRAME RAI

AT L OF FILL PIPE

INSTALL GROUND WIRE TO

SOUND METAL ON THE FRAME.

THIS HOSE IS PREFORMED; INSTALL SHORT EN D

THE METAL NECK AND CAP ASSEMBLY;

TRIM THE LONG END AS REQUIRED.

STEEL ELBOW

DO NOT TRIM

RECIRCULATION

STEEL TUBE

RECIRCULATION

HOSE CLAM

STEEL ELBOW

DO NOT TRIM

CAP

1/4 TURN - GASOLINE - LEV II

SCREW IN - DIESEL

NOTES:

TORQUE ALL WORM GEAR DRIVEN HOSE CLAMPS

TO 2.8 - 3.9 NEWTON METERS [25-35 IN. LB.]

[ ] DIMENSIONS ARE INCHES

* NOT SUPPLIED BY FORD MOTOR COMPANY

Remove and discard the Ford installed fuel ﬁll system components

(provided for shipping purposes only) except save and reuse the

metal neck and cap assembly.

Use the new hoses, pipes, scuff guards, tie wraps, and clamps

provided in the dunnage kit.

The completed fuel ﬁll system must provide a 4 degree minimum,

continuous, downward slope to the fuel tank. Additional support may

be required to prevent hose sagging which could cause spray or

spitback during normal fueling operations.

Do not extend the fuel ﬁll system outboard of the second unit body.

(CA) BACK OF CAB TO CENTERLINE OF REAR AXLE

56 INCH CA

WHEEL

BASE

Regular Cab

Super Cab

Crew Cab

3480mm [137.0]

4013mm [158.0]

4380mm [172.4]

MIN 620mm [24.4]

MAX 923mm [36.7]

MIN 540mm [21.25]

MAX 743mm [29.25]

MIN 267mm [10.5]

MAX 343mm [13.5]

FIGURE B – SUPER DUTY F-SERIES WIDE FRAME PICKUP BOX DELETE FUEL FILLER PIPE INSTALLATION

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 31 32

Commentaires sur ces manuels

Pas de commentaire

Ford SUPER DUTY F-SERIES 6C34-19A268-BA Manuel d'utilisateur Page 25

Commentaires sur ces manuels

Produits connexes et manuels pour Voitures Ford SUPER DUTY F-SERIES 6C34-19A268-BA