Ford SUPER DUTY F-SERIES 6C34-19A268-BA Manuel d'utilisateur télécharger pdf (Page 10)

F-SERIES (March, 2005)8

STATEMENTS OF CONFORMITY

The following Statements of Conformity apply to vehicles that are produced for sale or importation into the United States or

Canada. The term “Incomplete Vehicle Types” in these statements refers to the type of the vehicle illustrated on this manual’s

cover and listed in the chart on page 7.

The number preceding each Statement of Conformity refers to the number designation for a Part or a Section of Part 571 of the

Federal Motor Vehicle Safety Standard.

The statements provided for each safety standard number are appropriate compliance representations for each Canadian safety

standard number if this incomplete vehicle, identiﬁed by the VIN on the front of the document, was manufactured by Ford Motor

Company for sale or use in Canada, except as may be noted at the conclusion of each safety standard number.

PART

565.4 The statement below is applicable to all incomplete

vehicle types except the Basic (Stripped Chassis):

This vehicle, when completed, will conform to Part 565.4,

Vehicle Identiﬁcation Number, if the vehicle identiﬁcation

number mounted on the top of the instrument panel is not

removed, altered, or modiﬁed and no actions are taken by

the subsequent stage manufacturer that would obstruct

the readability of the Vehicle Identification Number

mounted on the top of the instrument panel.

101 The statements below are applicable to the Chassis

Cab:

This vehicle, when completed, will conform to Standard

101, Controls and Displays if:

• The controls, displays, and their identiﬁcations supplied

by Ford Motor Company are not removed, relocated,

altered, or modiﬁed.

• The components, wiring, and power supply installed by

Ford Motor Company to illuminate any control, display,

or their identiﬁcation are not removed or altered so as

to affect lighting performance.

• Components added to the vehicle do not obstruct the

driver’s ability to operate or visually locate the controls,

displays, and their identiﬁcations.

• The driver-seat is not replaced, relocated, or modiﬁed

other than for the addition of seat trim.

Any controls, displays, and illumination added to

this vehicle must conform to the requirements of this

Standard.

102 The statements below are applicable to the Chassis

Cab:

This vehicle, when completed, will conform to Standard

102, Transmission Shift Lever Sequence, Starter

Interlock, and Transmission Braking Effect, if no

alterations or adjustments are made to:

• Automatic Transmission – the transmission, shift cable,

transmission outer shift lever, shift cable bracket,

vacuum tubes, vacuum pump system, brake-shift

interlock system, the starter interlock system, and

wiring circuit from the interlock switch to the power

source.

• Manual and Automatic Transmission – the clutch-

ignition interlock system (if equipped), transmission

shift decal, knob, or transmission indicator dial

identiﬁcation.

If an auxiliary transmission is added to this vehicle, it

must conform to the requirements of this Standard.

103 The statement below is applicable to the Chassis

Cab:

This vehicle, when completed, will conform to Standard

103, Windshield Defrosting and Defogging Systems, if

no alterations or adjustments are made to heater and

blower assemblies, ducting, operating controls, electrical

circuit from the blower assembly to the power source,

windshield, coolant hoses from the radiator or engine to

the heater, and if no obstructions are added that restrict

or otherwise redirect the air flow from the defroster

outlets to the windshield.

104 The statement below Is applicable to the Chassis

Cab:

This vehicle when completed, will conform to Standard

104, Windshield Wiping and Washing Systems, if no

alterations are made to the windshield, the windshield

wiping and washing system, including the electrical

circuit from the windshield wiping and washing motors to

the power source, and if no obstructions are added that

restrict or otherwise redirect ﬂuid ﬂow from the washer

nozzles to the windshield.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Ford SUPER DUTY F-SERIES 6C34-19A268-BA Manuel d'utilisateur Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Voitures Ford SUPER DUTY F-SERIES 6C34-19A268-BA