Ford 2012 Fusion v.2 Manuel d'utilisateur

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Message center 18Entertainment Systems 28AM/FM stereo with CD/MP3 28Auxiliary

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

Create a MyKey威To program MyKey威 on one of the keys programmed to the vehicle,insert the key that you want to make a MyKey威 into the ignition. Turnthe

Clear MyKey威To reset all MyKeys威 as admin keys, do the following:1. Turn the vehicle on using the admin key.2. Press SETUP until PRESS RESET TO CLEAR

Note: For all vehicles, the number of MYKEY(S) PROGRAMMED orADMIN KEYS PROGRAMMED that is displayed in the MyKey威 systemstatus menus will include the

Condition Potential CausesCannot clear MyKey威 • Key in the ignition is a MyKey威• No MyKeys威 are programmed to thevehicle. Refer to Create a MyKey威sect

POWER DOOR LOCKS• Press the control to unlock alldoors.• Press thecontrol to lock alldoors.Smart locksThis feature attempts to help prevent you from l

Deactivating/activating autolock featureYour vehicle comes with the autolock features activated; there are fourmethods to enable/disable this feature:

Keyless entry keypad procedure1. Turn the ignition to the 1 offposition.2. Close all the doors.3. Enter factory–set 5–digit entrycode.4. Press and hol

Power door unlock/lock procedureBefore starting, ensure the ignition is in the off position and all vehicledoors are closed. You must complete Steps 1

CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the

INTERIOR LUGGAGE COMPARTMENT RELEASEYour vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of esc

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

REMOTE ENTRY SYSTEMThe Integrated Keyhead Transmitter (IKT) complies with part 15 of theFCC rules and with RSS-210 of Industry Canada. Operation is su

Unlocking the doors/two-stage unlock1. Press and release to unlock the driver’s door. Note: The interiorlamps will illuminate.2. Pressand release agai

Note: The panic alarm will only operate when the ignition is in the offposition.Opening the trunkPress twice within three seconds to open the trunk.•

How to reprogram your integrated keyhead transmitters (IKTs)To program a new integrated keyhead transmitter yourself, refer toProgramming spare keys i

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• open the trunk.Th

Anti-scan featureIf the wrong code has been entered seven times (35 consecutive buttonpresses), the keypad will go into an anti-scan mode. This mode d

Note: Large metallic objects, electronic devices that are used topurchase gasoline or similar items, or a second coded key on the samekey chain may ca

Automatic disarmingThe vehicle is disarmed immediately after the ignition is turned to the onposition.The theft indicator will illuminate for three se

Please read and understand theentire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition.2. Turn the igniti

PERIMETER ALARM SYSTEMThe perimeter anti-theft system will help protect your vehicle fromunauthorized entry.If there is any potential perimeter anti-t

WARNING LIGHTS AND CHIMESStandard instrument cluster shown; metric, optional and manualtransmission clusters similarWarning lights and gauges can aler

Disarming the systemYou can disarm the system by any of the following actions:• Unlock the doors by using the remote entry transmitter portion ofyour

FRONT SEATSWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the eve

The adjustable head restraintsconsist of:• a trimmed energy absorbing foamand structure (1),• two steel stems (2),• a guide sleeve adjust/releasebutto

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Tilting head restraints (if equipped)T

Pump the handle upwards to raisethe cushion and pump downward tolower the cushion to the desiredlocation.Pull lever up to adjust seatback.Using the ma

WARNING: Do not pile cargo higher than the seatbacks toreduce the risk of injury in a collision or sudden stop.WARNING: Always drive and ride with you

Move the control in the direction ofthe arrows to raise or lower thefront portion of the seat cushion.Move the control in the direction ofthe arrows t

Using the power lumbar support (if equipped)The power lumbar control is located on the outboard side of the driver’sseat.Press one side of the control

• Press twice to activate low heat.• Press a third time to deactivate.The indicator light on the control will illuminate when activated. For lowheat,

Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as possible to theba

damage your catalytic converter. Drive in a moderate fashion (avoidheavy acceleration and deceleration) and contact your authorized dealeras soon as p

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Center head restraintThe center head r

WARNING: The adjustable head restraint is a safety device.Whenever possible it should be installed and properly adjustedwhen the seat is occupied.To r

Split-folding rear seatbacksOne or both rear seatbacks can be folded down to provide additionalcargo space.To lower the seatback(s), pull therelease h

WARNING: Before returning the seatback to its originalposition, make sure that cargo or any objects are not trappedbehind the seatback. After returnin

• Front passenger sensing system• “Passenger airbag off” or “pass airbag off” indicator lamp• Front crash severity sensor.• Restraints Control Module

Driver’s seat position sensorThe driver’s seat position sensor allows your Personal Safety System totailor the deployment level of the driver dual-sta

Front safety belt usage sensorsThe front safety belt usage sensors detect whether or not the driver andfront outboard passenger safety belts are faste

If any of these things happen, even intermittently, have the PersonalSafety System serviced at an authorized dealer immediately. Unlessserviced, the s

WARNING: When possible, all children 12 years old and undershould be properly restrained in a rear seating position.WARNING: Safety belts and seats ca

Restraint of pregnant womenWARNING: Always ride and drive with your seatback uprightand the safety belt properly fastened. The lap portion of thesafet

Airbag readiness: If this light failsto illuminate when the ignition isturned to on, continues to flash orremains on, contact your authorizeddealer as

When to use the automatic locking modeThis mode should be used any time a child safety seat, except abooster, is installed in passenger front or rear

Energy management feature — front outboard• This vehicle has a safety belt system with an energy managementfeature at the front seats to help further

Safety belt height adjustmentYour vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shoulder b

Belt-Minder姞The Belt-Minder威 feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders byinterm

If... Then...The driver’s and front passenger’ssafety belts are buckled before theignition switch is turned to the onposition or less than 1-2 minutes

Reasons given... Consider...“Belts areuncomfortable”We design our safety belts to enhance comfort. Ifyou are uncomfortable - try different positionsfo

One-time disableIf at any time the driver/front passenger quickly buckles then unbucklesthe safety belt for that seating position, the Belt-Minder威 is

WARNING: While the design allows you to deactivate yourBelt-Minder威, this system is designed to improve your chances ofbeing safely belted and survivi

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The passenger airbag cover is a seamless design so that you cannot seethe boundary around its door. The shad

WARNING: All occupants of the vehicle, including the driver,should always properly wear their safety belts, even when an airbag supplemental restraint

Overdrive cancel and gradeassist (if equipped): Illuminateswhen the overdrive function of thetransmission has been turned offand the grade assist func

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

• a readiness light and tone• and the electrical wiring which connects the components• Side curtain airbag system. Refer to Side curtain airbag system

The front passenger sensing systemuses a ⬙passenger airbag off⬙ or⬙pass airbag off⬙ indicator which willilluminate and stay lit to remind youthat the

If a person of adult size is sitting in the front passenger’s seat, but the⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator lamp is lit, it ispos

The front passenger sensing system may detect small or medium objectsplaced on the seat cushion. For most objects that are in the frontpassenger seat,

WARNING: To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a chi

WARNING: Any alteration/modification to the front passengerseat may affect the performance of the front passenger sensingsystem.Determining if the sys

WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. Contact your authorize

The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of

Turn signal: Illuminates when theleft or right turn signal or thehazard lights are turned on. If theindicators flash faster, check for a burned out bu

Side-curtain airbag systemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a depl

How does the side air-curtain system work?The design and development of theside air curtain system includedrecommended testing proceduresthat were dev

The side air curtains are mounted to the sheet metal above the first andsecond row seats. In certain lateral collisions, the air curtain andseat-mount

Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref

SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfantsortoddlersChildren weighing 40 lb

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

WARNING: Always carefully follow the instructions andwarnings provided by the manufacturer of any child restraint todetermine if the restraint device

Transporting childrenAlways make sure your child is secured properly in a device that isappropriate for their age, height and weight. All children are

SAFETY SEATS FOR CHILDRENInfant and/or toddler seatsUse a safety seat that is recommended for the size and weight of the child.When installing a child

GAUGESStandard measure cluster shown, metric similar.Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine

Installing child safety seats with combination lap and shoulderbeltsCheck to make sure the child seat is properly secured before each use.When install

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out.6. All

10. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the

Your vehicle has LATCH loweranchors for child seat installation atthe seating positions marked withthe child seat symbol.The LATCH anchors are located

Use of inboard lower anchors from the outboard seating positions(center seating use)The lower anchors at the center of the second row rear seat are sp

The rear seats of your vehicle are equipped with built-in tether strapanchors located behind the seats as described below.The tether anchors in your v

2. Locate the correct anchor for theselected seating position.3. Open the tether anchor cover.4. Clip the tether strap to theanchor as shown.If the te

Child booster seatsThe belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child

Booster seats should be used until you can answer YES to ALL of thesequestions when seated without a booster seat:•Can the child sit all the way backa

Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the on position). The fuelgauge may vary slightly whe

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli

Temperature A B CWARNING: The temperature grade for this tire is establishedfor a tire that is properly inflated and not overloaded. Excessivespeed, u

• Cold inflation pressure: The tire pressure when the vehicle hasbeen stationary and out of direct sunlight for an hour or more andprior to the vehicl

Always inflate your tires to the Ford recommended inflation pressureeven if it is less than the maximum inflation pressure information foundon the tir

Note: If you overfill the tire, release air by pressing on the metal stem inthe center of the valve. Then recheck the pressure with your tire gauge.4.

Tire wearWhen the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Buil

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w

Info (information menu)Press INFO repeatedly to cyclethrough the following features:TRIP A/BRegisters the distance of individual journeys. Press and r

WARNING: Do not spin the wheels at over 35 mph (56 km/h).The tires may fail and injure a passenger or bystander.Driving habits have a great deal to do

Tire rotationRotating your tires at the recommended interval (as indicated in theScheduled Maintenance chapter) will help your tires wear more evenly,

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

7. H: Indicates the tire’s speed rating. The speed rating denotes thespeed at which a tire is designed to be driven for extended periods oftime under

9. M+S or M/S: Mud and Snow, orAT: All Terrain, orAS: All Season.10. Tire Ply Composition and Material Used: Indicates the number ofplies or the numbe

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

To restore the full functionality of the tire pressure monitoring system,have the damaged road wheel/tire repaired and remounted on yourvehicle. For a

Locks and Security 98Keys 98Locks 104Anti-theft system 115Seating and Safety Restraints 121Seating 121Personal Safety System™ 133Safety belt system 13

If you calculate your average fuel economy by dividing distance traveledby gallons of fuel used (liters of fuel used by 100 kilometers traveled),your

Low tirepressurewarning lightPossiblecauseCustomer action requiredFlashingwarning lightSpare tire inuseRepair the damaged road wheel/tireand reinstall

SNOW TIRES AND CHAINSWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel

VEHICLE LOADINGThis section will guide you in the proper loading of your vehicle to keepyour loaded vehicle weight within its design rating capability

WARNING: The appropriate loading capacity of your vehicle canbe limited either by volume capacity (how much space isavailable) or by payload capacity

Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment.GAW (Gross Axle Weight) – is the total weight

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

WARNING: Do not use replacement tires with lower loadcarrying capacities than the original tires because they maylower the vehicle’s GVWR and GAWR lim

• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the l

RECREATIONAL TOWINGFollow these guidelines for your specific powertrain combination to towyour vehicle for personal travel (such as behind a motor hom

If you tow your vehicle with all four wheels on the ground, follow theseinstructions:• Vehicles equipped with an automatic transmission should have th

System check and vehicle feature customizationPress the SETUP button repeatedlyto cycle the message center throughthe following features:RESET FOR SYS

STARTINGPositions of the ignition1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accesso

WARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine compartment and exhaus

• Make sure the gearshift is in P(Park).If starting a vehicle with a manualtransmission:• Make sure the parking brake isset.• Push the clutch pedal to

Starting the engine1. Turn the key to 3 (on) withoutturning the key to 4 (start).2. Turn the key to 4 (start), thenrelease the key as soon as theengin

ENGINE BLOCK HEATER (IF EQUIPPED)WARNING: Failure to follow engine block heater instructionscould result in property damage or physical injury.WARNING

• Be sure that areas where the vehicle is parked are clean and clear ofall combustibles such as petroleum products, dust, rags, paper andsimilar items

Four-wheel anti-lock brake system (ABS)Your vehicle is equipped with an anti-lock braking system (ABS). Thissystem helps you maintain steering control

Parking brakeTo set the parking brake (1), pullthe parking brake handle up as faras possible.The BRAKE warning lamp willilluminate and will remainillu

WARNING: Vehicle modifications involving braking system,aftermarket roof racks, suspension, steering system, tireconstruction and/or wheel/tire size m

It also includes a stability control light and a stability control off light.Both the stability control light and the stability control off light in t

OIL LIFEThis displays the remaining oil life.An oil change is required whenever indicated by the message center andaccording to the recommended mainte

If TCS is activated excessively in a short period of time, the brakingportion of the system may become temporarily disabled to allow thebrakes to cool

When the traction control system isoff, the stability control off light willilluminate steadily. Pressing thestability control switch again willturn o

The EPS system has diagnostic checks that continuously monitor theEPS system to ensure proper operation. When a system error isdetected, the following

• Heavy or uneven steering efforts may be caused by low power steeringpump fluid level. Check for low power steering pump fluid level beforeseeking se

If the fuse is not blown and the brake lamps are working properly, thefollowing procedure will allow you to move the gearshift lever from P(Park):1. A

WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your author

N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D

• Allows the transmission to select gears that will provide the desiredengine braking based on the vehicle inputs mentioned above. This willincrease e

Understanding the gearshift positions of the 6–speed automatictransmission equipped with a 3.0L or 3.5L V6 Duratec姞 engine(if equipped)Your vehicle ha

R (Reverse)With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Re

Press RESET to turn it off or on.PARK AID (Reverse sensing system–if equipped)This feature sounds a warning tone to warn the driver of obstacles neart

Vehicles equipped with the 3.5LengineInitially when moving the lever to the manual mode (M), the instrumentcluster will show the current selected gear

Engine damage may occur if excessive engine revving is heldwithout shifting.Recommended shift speedsUpshift according to the following chart:Upshifts

5. Release the parking brake, then slowly release the clutch pedal whileslowly pressing on the accelerator.During each shift, the clutch pedal must be

4. Shift into R (Reverse) by pushingthe gearshift knob down, thenmoving the lever fully to the left,then forward.Note: The gearshift lever can only be

REVERSE SENSING SYSTEM (IF EQUIPPED)The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when the R (Rev

The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to th

REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rearview camera system,located on the trunk, provides avideo image which appears in therear view mirror or on

The camera lens for the camera is located on the trunk. Keep the lensclean so that the video image remains clear and undistorted. Clean thelens with a

BLIND SPOT MIRRORS (IF EQUIPPED)Blind spot mirrors have an integrated convex spotter mirror built intothe upper outboard corner of the outside mirrors

BLIND SPOT INFORMATION SYSTEM (BLIS姞) WITH CROSSTRAFFIC ALERT (CTA) (IF EQUIPPED)The BLIS威 is a convenience featurethat aids the driver in assessingwh

DRIVER DOOR AJAR — Displayed when the driver’s door is notcompletely closed.PASSENGER DOOR AJAR — Displayed when the passenger side dooris not complet

The BLIS威 will trigger the alert for vehicles that enter your blind zonefrom the rear or merge in to the blind zone from the side. Vehicles thatyou pa

Cross traffic alert (CTA) system operationThe CTA system warns the driver of approaching vehicles when R(Reverse) is selected and the vehicle is backi

CTA coverage also decreases when parking at shallow angles (refer tofigure for approximate zone coverage areas [sensor obstructed tovehicle on left]).

CTA and Reverse Sensing System (RSS) interactionCTA works along with the Reverse Sensing System (RSS) (if equipped).Become familiar with the warning t

WARNING: Just prior to the system recognizing a blockedcondition and alerting the driver, the number of missed objectswill increase. To help avoid inj

ALL-WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED)Your vehicle may be equipped with a full-time all-wheel drive (AWD)system. The AWD system is an active syste

If your vehicle goes off the edge of the pavement• If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ea

Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle (i.e.,

Mud and waterIf you must drive through high water, drive slowly. Traction or brakecapability may be limited.When driving through water, determine the

Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should

SERVICE ADVANCETRAC — Displayed when the AdvanceTrac威system has detected a condition that requires service.TRUNK AJAR — Displayed when the trunk is no

Avoid sudden braking as well. Although an AWD vehicle may acceleratebetter than a two-wheel drive vehicle in snow and ice, it won’t stop anyfaster, be

DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly. Never drive through waterthat is higher than the bot

ROADSIDE ASSISTANCEVehicles sold in the U.S. : Getting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany off

Vehicles sold in the U.S. : Using roadside assistanceComplete the roadside assistance identification card and place it in yourwallet for quick referen

FUEL PUMP SHUT-OFF SWITCH (3.5L ENGINE)This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial

WARNING: Failure to inspect and if necessary repair fuel leaksafter a collision may increase the risk of fire and serious injury.Ford Motor Company re

Passenger compartment fuse panelThe fuse panel is located below and to the left of the steering wheel bythe brake pedal. Remove the panel cover to acc

Fuse/RelayLocationFuse AmpRatingProtected Circuits7 10A Low beam headlamps (left)8 10A Low beam headlamps (right)9 15A Courtesy lamps10 15A Backlighti

Fuse/RelayLocationFuse AmpRatingProtected Circuits35 10A Rear park assist, Blind spot monitorsystem, Heated seats, AWD, Rearvideo camera36 5A Passive

Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot

AWD OFF (if equipped) — Displayed when the AWD system has beenautomatically disabled to protect itself. This is caused by operating thevehicle with th

Fuse/RelayLocationFuse AmpRatingProtected Circuits3 40A* Powertrain control module (PCM)(relay 57 power)4 — Not used5 30A* Starter motor (relay 55 pow

Fuse/RelayLocationFuse AmpRatingProtected Circuits29 20A* Front power point30 30A* Fuel relay (relay 54 power)31 30A* Passenger power seat32 30A* Driv

Fuse/RelayLocationFuse AmpRatingProtected Circuits55 Full ISO relay Starter relay56 — Not used57 Full ISO relay PCM relay58 — Not used* Cartridge Fuse

Dissimilar spare tire/wheel informationWARNING: Failure to follow these guidelines could result in anincreased risk of loss of vehicle control, injury

• All-wheel driving capability (if applicable)3. Full-size dissimilar spare without label on wheelWhen driving with the full-size dissimilar spare tir

Removing the spare tire and jack1. Remove the carpeted load floorpanel located in the rear of thevehicle and remove the lug wrenchand long bolt from t

1. Block both the front and rear ofthe wheel diagonally opposite theflat tire. For example, if the leftfront tire is flat, block the right rearwheel.2

WARNING: To lessen the risk of personal injury, do not put anypart of your body under the vehicle while changing a tire. Do notstart the engine when y

WHEEL LUG NUT TORQUE SPECIFICATIONSRetighten the lug nuts to the specified torque within 100 miles (160 km)after any wheel disturbance (tire rotation,

RUNNING OUT OF FUELIf you have run out of fuel and need to refill the vehicle with a portablefuel container, see Running out of fuel in the Maintenanc

VEHICLE NEAR TOP SPEED — Displayed when a MyKey威 is in useand the MyKey speed limit is on and the vehicle speed is approaching80 mph (130 km/h). Refer

3.Park the booster vehicle close to the hood of the disabled vehicle makingsure the two vehicles do not touch. Set the parking brake on both vehiclesa

Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

If the vehicle is towed by other means or incorrectly, vehicledamage may occur.If your vehicle is to be towed using wheel lift equipment, the non-lift

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehi

• Service specials and promotions.In Canada:Mailing addressCustomer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ont

IN CALIFORNIA (U.S. ONLY)California Civil Code Section 1793.2(d) requires that, if a manufactureror its representative is unable to repair a motor veh

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

If your vehicle must be serviced while you are traveling or living inAsia-Pacific Region, Sub-Saharan Africa, U.S. Virgin Islands, CentralAmerica, the

AUDIO SYSTEMSAM/FM/single CD MP3 satellite compatible sound systemWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and

If you buy your vehicle in North America and then relocate to any of theabove locations, register your vehicle identification number (VIN) andnew addr

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

WAXING• Wash the vehicle first.• Use a quality wax that does not contain abrasives.• Do not allow paint sealant to come in contact with any non-body(l

• Do not spray a hot engine with cold water to avoid cracking theengine block or other engine components.• Spray Motorcraft威 Engine Shampoo and Degrea

3.0L ENGINE3.5L ENGINEPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your aut

WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub

• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to a

• If a ring forms on the fabric after spot cleaning, clean the entire areaimmediately (but do not oversaturate) or the ring will set.• Do not use hous

FORD AND LINCOLN CAR CARE PRODUCTSYour Ford or Lincoln authorized dealer has many quality productsavailable to clean your vehicle and protect its fini

AM/FM Radio/ VOL (Power/Volume): Press to turn the radio on/off. Turn theknob to increase/decrease volume.If the volume is set above a certain level a

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

Working with the engine on1. For vehicles equipped with an automatic transmission, set the parkingbrake and shift to P (Park). For vehicles equipped w

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.5L I4 engine1. Engine coolant reservoir2. Engine oil filler cap3. Engine oil dipstick4. Brake/Clutch

3.0L V6 engine1. Engine coolant reservoir2. Brake fluid reservoir3. Transmission fluid dipstick (automatic transmission only)4. Battery5. Power distri

3.5L V6 engine1. Power steering fluid reservoir2. Transmission fluid dipstick3. Brake fluid reservoir4. Battery5. Power distribution box6. Air filter

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

Replace wiper blades at least once per year for optimum performance.Poor wiper quality can be improved by cleaning the wiper blades and thewindshield.

• 3.0L V6 engine• 3.5L V6 engine6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.Maintenance and Specifications2972012 Fusi

•If the oil level is within thisrange, the oil level is acceptable.DO NOT ADD OIL.•If the oil level is below this mark,engine oil must be added to rai

• 3.5L V6 engineIf required, add engine oil to the engine. Refer to Adding engine oil inthis chapter.•Do not overfill the engine withoil. Oil levels a

Customer Assistance 274Reporting safety defects (U.S. only) 281Reporting safety defects (Canada only) 281Cleaning 282Maintenance and Specifications 29

CAT/FOLD (Category/Folder): This feature allows you to select fromvarious music categories.To change RDS categories: Press MENU repeatedly until RDS O

Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils certified for gasoline engines by the

BATTERYYour vehicle is equipped with aMotorcraft威 maintenance-freebattery which normally does notrequire additional water during itslife of service.If

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the FULL COLD level, or within theCOLD

• DO NOT MIX different colors or types of coolant in your vehicle.Make sure the correct coolant is used. Mixing of engine coolants mayharm your engine

Add the proper mixture of coolant and water to the cooling system byfollowing these steps:1. Before you begin, turn the engine off and let it cool.2.

7. Close the bleed valve and reinstall the cap on the coolant reservoir.Turn the cap until it is tightly installed to prevent coolant loss.After any c

• If available, refer to the chart on the coolant container toensure the coolant concentration in your vehicle will provideadequate freeze protection

Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to an authorized dealer as soon as possible to minimizeengine damage

TEXT:In MP3 mode only– Press TEXT repeatedly to view Album (AL), Folder(FL), Song (SO) and Artist (AR) in the display, if available.In TEXT MODE: Some

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsWARNING: Do not overfill the fuel tank. The pressure in anoverfilled tank may c

• Fuels can also be harmful if absorbed through the skin. If fuel issplashed on the skin and/or clothing, promptly remove contaminatedclothing and was

WARNING: When refueling always shut the engine off andnever allow sparks or open flames near the filler neck. Neversmoke while refueling. Fuel vapor i

Easy Fuel姞 “no cap” fuel systemYour fuel tank is equipped with an Easy Fuel威 “no cap” fuel filler system.This allows you to simply open the fuel fille

Flex fuel vehicle (FFV) fuel fill inletIf your vehicle is flex fuel capable, it will have a yellow bezel placed overthe fuel fill inlet.Choosing the r

It is best not to alternate repeatedly between gasoline and E85. If you doswitch fuels, it is recommended that you add as much fuel aspossible—at leas

Running out of fuelAvoid running out of fuel because this situation may have an adverseeffect on powertrain components.If you have run out of fuel:• Y

1. Locate the white plastic funnel. Itis attached to the underside of thespare tire cover or is included withthe tire changing tools.2. Slowly insert

The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fue

Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin

SCAN: Press SCAN for a brief sampling of all available SIRIUS威 satellitechannels. If a specific category is selected, (Jazz, Rock, News, etc.) pressSC

• Adding certain accessories to your vehicle (for example; bugdeflectors, rollbars/light bars, running boards, ski/luggage racks) mayreduce fuel econo

If other than Ford, Motorcraft威 or Ford-authorized parts are used formaintenance replacements or for service of components affectingemission control,

electrical system dry out. After three driving cycles without these or anyother temporary malfunctions present, the service engine soonindicator shoul

Allow the vehicle to sit for at least eight hours without starting theengine. Then, start the engine and complete the above driving cycle. Theengine m

BRAKE/CLUTCH FLUIDBrake and clutch (if equipped) systems are supplied from the samereservoir.• 2.5L engine• 3.0L/3.5L enginesThe fluid level will drop

Checking automatic transmission fluid at normal operatingtemperature (140°F-158°F [60°C-70°C])Automatic transmission fluid expands when warmed. To obt

Low fluid levelDo not drive the vehicle if the fluidlevel does not show at all on thedipstick.Driving the vehicle with less thanthe recommended fluid

Checking automatic transmission fluid (6F35) (if equipped)Refer to your scheduled maintenance information for scheduledintervals for fluid checks and

The transmission fluid should be inthe zone, identified by the arrows inthis figure, if at normal operatingtemperature 185°F-200°F(85°C-93°C).High flu

This fluid level is within the normaloperating fluid range and does notrequire that you have your fluidlevel readjusted after recreationalflat tow ope

• SONG SEEK MENU- Press OK to enter song seek menu.Press/ to scroll through the following options:a. SAVE THIS SONG: Press OK to save the currently pl

Changing the air filter element• 2.5L I4 engine• 3.0L V6 engine• 3.5L V6 engine1. Release the clamps that secure the air filter housing cover.2. Caref

• 2.5L I4 engine• 3.0L V6 engine• 3.5L V6 engine3. Remove the air filter element from the air filter housing.Maintenance and Specifications3312012 Fus

4. Wipe the air filter housing and cover clean to remove any dirt ordebris and to ensure good sealing.5. Install a new air filter element. Be careful

• Cover interior trim to prevent fading.• Keep all rubber parts free from oil and solvents.Engine• The engine oil and filter should be changed prior t

Tires• Maintain recommended air pressure.Miscellaneous• Make sure all linkages, cables, levers and pins under vehicle arecovered with grease to preven

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number / FordspecificationBrake (and clutch–ifequipped) fluidBe

Item Capacity Ford part nameFord part number / FordspecificationEngine coolant(3.0L engine)110.6 quarts(10.0L)Motorcraft威 SpecialtyGreen Engine Coolan

Item Capacity Ford part nameFord part number / FordspecificationLock cylinders —Motorcraft威Penetrating and LockLubricantXL-1/NonePower steering fluid(

Item Capacity Ford part nameFord part number / FordspecificationWindshield washerfluidFill as requiredMotorcraft威 PremiumWindshield WasherConcentrate

ENGINE DATAEngine 2.5L I4 engine 3.0L V6 engine 3.5L V6 engineCubic inches 151 182 214Required fuelMinimum87 octaneMinimum87 octaneMinimum87 octaneFir

• CHANNEL LOCKOUT MENU- Press OK to enter the ChannelLockout menu. Press the / to scroll through the followingoptions:a. LOCK/UNLOCK THIS CHANNEL: Pre

• 3.5L V6 Engine1. Short drivebelt is on first pulley groove closest to engine.2. Long drivebelt is on second pulley groove farthest from engine.IDENT

Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX

TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C

Peace of mind•Remote start •Wheel locks•Vehicle security systems •Keyless entry keypad•Locking fuel plug for capless fuel system•Bumper mounted parkin

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 32 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan3472012 Fusion (fsn)Owners Guide, 2nd PrintingUSA (fus)

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is

GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?Carefully following this schedule helps protect against major repairexpenses resulting from n

Use SEEK/TRACK to adjust between SPEED OFF and levels1–7: Increasing the level from 1 (lowest setting) to 7 (highest setting)allows the radio volume t

Your vehicle is very sophisticated and built with multiple complexperformance systems. Every manufacturer develops these systems usingdifferent specif

Genuine Ford parts and serviceWhen planning your maintenance services, consider your dealership for allyour vehicle’s needs.There are a lot of reasons

Engine oil/coolant change intervalsEngine oil As indicated by the message center: do notexceed one year or 10,000 miles (16,000 km)Engine coolant,init

Multi-point inspectionIn order to keep your vehicle running right, it is important to have thesystems on your vehicle checked regularly. This can help

Scheduled Maintenance3542012 Fusion (fsn)Owners Guide, 2nd PrintingUSA (fus)

NORMAL SCHEDULED MAINTENANCE AND LOGIntelligent Oil Life Monitor™Your vehicle is equipped with an Intelligent Oil Life Monitor™ thatdetermines when th

Normal Scheduled MaintenanceAt every oil changeinterval as indicatedby the messagecenterChange engine oil and filterRotate tires, inspect tire wear an

Additional maintenance items1Miles (x 1,000) 20 30 40 60 80 90 100 120 140 150Kilometers (x 1,000) 32 48 64 96 128 144 160 192 225 240Replace cabin ai

Maintenance schedule logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDAT

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

Your vehicle is equipped with anauxiliary input jack (AIJ). Theauxiliary input jack provides a wayto connect your portable musicplayer to the in-vehic

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

SPECIAL OPERATING CONDITIONSIf you operate your vehicle primarily in any of the following conditions,you need to perform additional maintenance as ind

Perform the services in the preceding table when specified or within3,000 miles (4,800 km) of the OIL CHANGE REQUIRED messageappearing in the message

Special operating condition logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

EXCEPTIONSThere are several exceptions to the Normal Schedule. They are listedbelow:Normal vehicle axle maintenance: Rear axles and power take-off(PTO

Edge/MKX AWD only – vehicles operating off-road in sand during highambient temperatures must replace the AWD PTU (All-wheel drivePower Transfer Unit)

AAccessory delay ...82AdvanceTrac ...217Airbag supplemental restraintsystem ...

Changing a tire ...262Child safety seats ...169attaching with tether straps ..175in front seat ...

Emission control system ...320Engine ...339cleaning ...283coolant ...

Troubleshooting:1. Do not connect the audio input jack to a line level output. Line leveloutputs are intended for connection to a home stereo and are

manual heating and airconditioning system ...45Hood ...291IIgnition ...

MyKey ...99NNavigation system ...44OOctane rating ...314Oil (see E

Seats ...121child safety seats ...169front seats ...123heated ...

Ventilating your vehicle ...213WWarning lights (see Lights) ...12Washer fluid ...295Water, Driving through ...

Your vehicle may be equipped with aUSB port inside your center console.This feature allows you to plug inmedia playing devices, memorysticks, and also

• Wipe discs from the center out.Don’t:• Expose discs to direct sunlight or heat sources for extended periodsof time.• Clean using a circular motion.C

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

MP3 track and folder structureYour MP3 system recognizes MP3 individual tracks and folder structureas follows:• There are two different modes for MP3

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredINVALID CHNL Channel no longeravailable.This previouslyavailable channel is nolonger available. Tuneto another

Radio Display Condition Action RequiredUPDATING Update of channelprogramming inprogress.No action required. Theprocess may take up tothree minutes.CAL

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1.Fan speed adjustment: Turn to select fan speed.2.RRear defroster: Press to activate/deactivat

9. Temperature control: Controls the temperature of the airflow in thevehicle.10. Recirculated air: Press to activate/deactivate air recirculationin t

• To improve the time to reach comfort in hot weather, drive with thewindows slightly open for 2-3 minutes after start up or until thevehicle has been

DUAL AUTOMATIC TEMPERATURE CONTROL (IF EQUIPPED)1. AUTO/Driver temperature: Press to engage full automaticoperation. Select the desired temperature us

5. Power/ : Press to activate/deactivate the climate controlsystem. When the system is off, outside air is prevented from enteringthe vehicle through

Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti

14. Driver heated seat control (if equipped): Press toactivate/deactivate the driver heated seat. See Heated seats in theSeating and Safety Restraints

3. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. A/Cengages automaticall

11. Power: Press to activate/deactivate the climate control system.When the system is off, outside air is prevented from entering thevehicle. The clim

• : Distributes air through the windshield defroster vents, de-mistervents, floor vents and rear seat floor vents. The system willautomatically provid

For maximum cooling performance:• Automatic operation:1. Press AUTO for full automatic operation.2. Do not override A/C or(recirculated air).3. Set th

Do not use razor blades or other sharp objects to clean the insideof the rear window or to remove decals from the inside or therear window. This may c

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the low beam headlampso

4. Turn the headlamp control to the autolamp position. The headlampswill turn on.5. Wait the desired amount of time for the exit delay you want (up to

Flash-to-passPull toward you slightly to activateand release to deactivate.Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a redu

AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident, the alignment of y

SPECIAL NOTICESNew Vehicle Limited WarrantyFor a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited

5. Locate the vertical adjuster oneach headlamp. Using a Phillips #2screwdriver, turn the adjuster eitherclockwise (to adjust down) orcounterclockwise

Your vehicle may also have readinglamps within the rear dome lamp(s).Press the switches on either side ofthe dome lamp to turn on thelamps.Ambient lig

• Large water droplets, drip marks or streaks present on the interior ofthe lensTake your vehicle to a dealer for service if any of the above conditio

Replacing interior bulbsCheck the operation of all bulbs frequently.Replacing exterior bulbsCheck the operation of all the bulbs frequently.Replacing

Low beam6. Disconnect the electrical connector.To install, reverse the removal procedure.For passenger side replacement of the high beam bulb, do thef

6. Disconnect the electricalconnector.7. Carefully pull bulb straight out ofsocket and install the new one.WARNING: Handle a halogen headlamp bulb car

3. Reaching through the wheel well,remove the rubber bulb accesscover from the housing.4. Remove the bulb socket by rotating it counterclockwise, then

Replacing headlamp bulbs (3.5L engine)High beam/low beam bulb replacementFor driver side replacement of the high beam/low beam bulbs, do thefollowing:

Replacing front parking lamp/turn signal bulbs (2.5L/3.0L engines)1. Make sure headlamp control is in the off position, then open the hood.2. Reach ov

Replacing front parking lamp/turn signal bulb (3.5L engine)For driver side replacement of the front parking lamp/turn signalbulb, do the following:WAR

Event Data RecordingThis vehicle is equipped with an event data recorder (EDR). Themain purpose of an EDR is to record, in certain crash or nearcrash-

For passenger side replacement of the front park/turn signal bulb, dothe following:1. Turn the steering wheel left to gain access to the wheel well.2.

4. With the bulb exposed, carefullyremove the bulb from the socket bygrasping the bulb and pulling itaway from the wire harness.Replace with a new bul

4. Remove the bulb socket byturning it counterclockwise andpulling it straight out.5. Pull the bulb from the socket andpush in the new bulb.6. Install

Replacing fog lamp bulbs1. Make sure the fog lamp switch isin the off position.2. From underneath the vehicle,partially remove the tire splashshield b

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Windshield washer: Press the endof the stalk:• briefly: causes a single swipe ofthe wipers without washer fluid.• a quick press and hold: thewipers wi

WARNING: Never adjust the steering wheel when the vehicle ismoving.ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mir

OVERHEAD CONSOLEThe appearance of your vehicle’s overhead console will vary according toyour option package.Storage compartmentPress on the rear edge

Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the on p

2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons.3. Slowly d

Note: Including to the extent that any law pertaining to EventData Recorders applies to SYNC威 or its features, please note thefollowing: Once 911 Assi

INSTRUMENT PANEL STORAGE COMPARTMENTThe storage compartment may beused to secure sunglasses or similarsized objects. Press the button toopen the stora

POWER WINDOWSWARNING: Do not leave children unattended in the vehicle anddo not let children play with the power windows. They mayseriously injure the

• If or is pressed during the opening operation, both windowsand moon roof movement will stop.Note: The ignition must be in the off position and the a

INTERIOR MIRRORThe interior rearview mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side.W

EXTERIOR MIRRORSPower side view mirrorsWARNING: Do not adjust the mirror while the vehicle is inmotion.To adjust your mirrors:1. Rotate the control cl

Using speed controlsThe speed controls are located on the steering wheel. The followingbuttons work with speed control:– SET +: Press to set a speed o

Resuming a set speedPress and release RSM. This will automatically return the vehicle to thepreviously set speed.Increasing speed while using speed co

STEERING WHEEL CONTROLS (IF EQUIPPED)Radio control featuresVOL + (Volume): Press to increasethe volume.VOL – (Volume): Press to decreasethe volume.(Se

For further information on the SYNC威 system, refer to the SYNC威supplement.Navigation system/SYNC威 handsfree control features (ifequipped)Presscontrol

WARNING: When closing the moon roof, you should verify thatit is free of obstructions and ensure that children and/or pets arenot in the proximity of

WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends that youuse extreme caution when

Note: If equipped with global open windows, you can open the vehicle’sfront windows and moon roof (if equipped) by using the control on theremote tran

Additional Car2U威 system information can be found on-line atwww.learcar2U.com or by calling the toll-free Car2U威 system help line at1-866-572-2728.Typ

Note: Do not program the Car2U威 system with the vehicle in the garage.Make sure that your key is on and engine off while programming thetransmitter.1.

After successful programming, you will be able to operate your Car2U威system by pressing the button you programmed to activate the opener.The indicator

Switchposition 12345678 9101112Up, onor +LLLLLLLLLLLLMiddle,neutralor 0MMMMMMMMMMMMDown,offor–RRRRRRRRRRRRL=left; M=middle; R=right3. To input these p

After successful programming, you will be able to operate your Car2U威system by pressing the button you programmed to activate the opener.The indicator

POSITIVE RETENTION FLOOR MATWARNING: Always use floor mats that are designed to fit thefoot well of your vehicle. Only use floor mats that leave the p

WARNING (Continued)• Failure to properly follow floor mat installation or attachmentinstructions can potentially cause interference with pedal operati

KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unl

MYKEY姞The MyKey威 feature allows you to program a restricted driving mode topromote good driving habits. All but one of the keys programmed to thevehic