Introduction 5Instrument Cluster 14Warning lights and chimes 14Gauges 21Message center 22Entertainment Systems 60AM/FM stereo 60AM/FM stereo with CD 6
Note: Including to the extent that any law pertaining to EventData Recorders applies to SYNC威 or its features, please note thefollowing: Once 911 Assi
Slide-on-rod feature (ifequipped)Rotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage.Note: To stow the viso
CENTER CONSOLE (IF EQUIPPED)Your vehicle may be equipped with a variety of console features. Theseinclude:• Locking storage compartmentwith hanging fi
Auxiliary power points can be found in the following locations:• On the instrument panel (two locations)• Inside the center console storage compartmen
Note: The 110V AC power point isequipped with a cap which providesprotection from inserting objectsinto the socket. The cap shouldalways be in a close
Green light is blinking — Power point is in fault modeNote: The 110V AC power point will turn off after 13 minutes if theignition is in the on positio
Window lock (if equipped)The window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controls(except for the
INTERIOR MIRRORThe interior rearview mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side.W
To adjust your mirrors:1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror.2. Mo
To operate the power-fold mirrors:1. Rotate the switch to the center/neutral position.2. Momentarily pull the switch rearward to auto fold in.3. Momen
Note: If the power fold/telescope mirror glass appears loose or vibrateswhen driving, it is possible that the mirrors have been manually folded ortele
CELL PHONE USEThe use of mobile communications equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri
Mirror-mounted side turn signal indicator (if equipped)When the vehicle turn signals areactivated, the outer portion of themirror housing will blink a
The accelerator and brake pedal positions are saved when doing amemory set function and can be recalled along with the vehiclepersonality features whe
Note:• Vehicle speed may vary momentarily when driving up and down asteep hill.• If the vehicle speed increases above the set speed on a downhill, you
STEERING WHEEL CONTROLS (IF EQUIPPED)Audio control featuresMEDIA: Press repeatedly to scrollthrough available audio modes.SEEK : Press to selectthe pr
Press to scroll through various menus and selections. PressOK to confirm your selection.For further information on the SYNC威 system, refer to the SYNC
The relays are coded as shown inthe accompanying illustration.There will also be one power leadfor each switch found as a blunt-cutand sealed wire loc
WARNING: When closing the moon roof, you should verify thatit is free of obstructions and ensure that children and/or pets arenot in the proximity of
UNIVERSAL GARAGE DOOR OPENER (IF EQUIPPED)Your vehicle may be equipped with a universal garage door opener whichcan be used to replace the common hand
Types of garage door openers (rolling code and fixed code)The Car2U威 Home Automation System may be programmed to operaterolling code and fixed code ga
1. Firmly press the two outerCar2U威 system buttons for1–2 seconds, then release.2. Go to the garage to locate thegarage door opener motor and its“lear
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
The indicator light above the selected button will turn on to confirm thatthe Car2U威 system is responding to the button command.To program another rol
Switchposition 12345678 9101112Up, onor +LLLLLLLLLLLLMiddle,neutralor 0MMMMMMMMMMMMDown,offor–RRRRRRRRRRRRL=left; M=middle; R=right3. To input these p
After successful programming, you will be able to operate your Car2U威system by pressing the button you programmed to activate the opener.The indicator
POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)WARNING: Always use floor mats that are designed to fit thefoot well of your vehicle. Only use floor mats th
WARNING (Continued)• Failure to properly follow floor mat installation or attachmentinstructions can potentially cause interference with pedal operati
1. Before removal of the tailgate,locate and disconnect the tailgatein-line connector under the pickupbox on the passenger side of thevehicle near the
Tailgate step (if equipped)Your vehicle may be equipped with a feature that allows easier entry intothe truck bed. To open the tailgate step:1. Flip d
Note:• Fully close and latch the tailgate step before moving the vehicle.• Never drive with the step or grab handle deployed.• Replace slip resistance
3. Rotate the panels toward thetailgate.Repeat Steps 1–3 for the other side of the bed extender.4. Connect the two panels, then rotate both knobs a qu
Note: When the vehicle is in motion, ensure the locking pins and knobsare fully engaged.Note: Ensure all cargo is secured.Note: When the vehicle is in
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
KEYSYour vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and
• The audio system will be muted whenever Belt-Minder威 is activateduntil the safety belts are buckled. Refer to the Seating and SafetyRestraints chapt
For optional message center:1. At the main menu screen select SETTING then MYKEY by pressingOK or the right arrow key.2. Press OK to select CREATE MYK
For optional message center:1. At the main menu screen select SETTING then MYKEY by pressingOK or the right arrow key.2. Use the up and down arrows to
Refer to Message center in the Instrument Cluster chapter for MyKey威system warnings displays.Using MyKey威 with remote start systemsMyKey威 is not compa
Note: For all vehicles, the number of MYKEY(S) PROGRAMMED orADMIN KEYS PROGRAMMED that is displayed in the MyKey威 systemstatus menus will include the
TroubleshootingCondition Potential CausesCan’t create a MyKey威 • Key in the ignition is already aMyKey威.• Key in the ignition is the lastremaining adm
Condition Potential CausesLost any key • For programming spare keys, referto the Programming spare keyssection in this chapter.I accidentally programm
Condition Potential CausesMyKey威 distance does notaccumulate• MyKey威 is not being used by theintended user.• MyKey威 system has been recentlycleared.•
The vehicle can still be locked, with the key in the ignition, using themanual lock button on the door, locking the driver’s door with a key, bysimult
WARNING LIGHTS AND CHIMESBase instrument cluster with standard measure shown; metricsimilarOptional instrument cluster with standard measure shown; me
1. Place the key in the ignition andturn the ignition to the on position.2. Press the power door unlockcontrol on the door panel threetimes.3. Turn th
Note: The doors will not autounlock if the vehicle has beenelectronically locked before the driver door is opened.Deactivating/activating autounlock f
Keyless entry keypad autounlock enable/disable procedure1. Turn the ignition to the offposition.2. Close all the doors.3. Enter factory–set 5–digit en
REMOTE ENTRY SYSTEM (IF EQUIPPED)The integrated keyhead transmitter (IKT) complies with part 15 of theFCC rules and with RSS-210 of Industry Canada. O
Two step door unlocking1. Press and release to unlock the driver’s door. Note: The parkinglamps and interior lamps will illuminate (refer to the Illum
Note: The panic alarm will only operate when the ignition is off.Memory feature (seat, mirrors and adjustable pedals)The integrated keyhead transmitte
Integrated keyhead transmitter (IKT)To replace the battery:1. Twist a thin coin in the slot nearthe key ring to remove the batterycover (1).Note: Do n
The illuminated entry system will turn off the lights if:• the ignition switch is turned to the on position, or• the remote transmitter lock control i
• Two remote vehicle starts have already been attempted within the lasthour.• The vehicle is not in P (Park).Starting the engine with remote startTo s
You can disable or enable the remote start system through the messagecenter. Refer to Message center in the Instrument Cluster chapter.SECURICODE™ KEY
Standard message centerNote: Some warning lights arereconfigurable telltale (RTT)indicator lights and will illuminate inthe message center. These ligh
Erasing personal code1. Enter the factory set 5–digit code.2. Within five seconds, press the 1 • 2 on the keypad and release.3. Press and hold the 1 •
Note: The SecuriLock威 passive anti-theft system is not compatible withnon-Ford aftermarket remote start systems. Use of these systems mayresult in veh
1. Insert the first previouslyprogrammed coded key into theignition and turn the ignition fromthe 1 (off) position to the 3 (on)position (maintain ign
Arming the systemWhen armed, this system will respond if unauthorized entry isattempted. When unauthorized entry occurs, the system will flash thepark
FRONT SEATSWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the eve
The adjustable head restraintsconsist of :• a trimmed energy absorbing foamand structure (1),• two steel stems (2),• a guide sleeve adjust/releasebutt
To reinstall the adjustable head restraint, do the following:1. Insert the two stems (2) into theguide sleeve collars.2. Push the head restraint downu
The non-adjustable head restraintsconsist of:• a trimmed energy absorbing foamand structure (1),• two steel stems (2),• and two guide sleeveunlock/rem
WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Front seat• Lift the track release bar
Pull up on the tab to open thestorage bin.Lift up on the seatback to return it to the upright position.To gain access to the under-seatstorage compart
WARNING: Under engine misfire conditions, excessive exhausttemperatures could damage the catalytic converter, the fuelsystem, interior floor coverings
Adjusting the front power seat (if equipped)Move the front of the control up ordown to tilt the seat cushion.Move the rear of the control up ordown to
Using the power lumbar support (if equipped)The power lumbar control is located on the outboard side of the seat.Press one side of the control toadjus
Note: Do not do the following:• Place heavy objects on the seat• Operate the seat heater if water or any other liquid is spilled on theseat. Allow the
To remove an air filter:1. Turn the vehicle off.2. Push up on the outside rigid edgeof the filter until the tabs arereleased, then rotate the air filt
Memory seats/power mirrors/adjustable pedals (if equipped)This system allows automaticpositioning of the driver seat, powermirrors, and adjustable ped
The easy out feature automatically moves the driver’s seat 2 inches(5 cm) backward when:• the transmission is in P (Park)• the key is removed from the
Center head restraint (Crew Cab)The non-adjustable second row head restraints consist of :• a trimmed energy absorbing foam and structure (1),• two st
Returning the seat to seating positionWARNING: Make sure that cargo or any objects are not trappedunderneath the seat cushion before returning the sea
1. Pull control on the side of the seat to release seat cushion fromstorage position.2. Push seat cushion down until it locks into horizontal position
Use your vehicle key to lock thestorage space.SAFETY RESTRAINTSWARNING: Always drive and ride with your seatback uprightand the lap belt snug and low
WARNING: Driving a vehicle with the brake system warninglight on is dangerous. A significant decrease in brakingperformance may occur. It will take yo
WARNING: Each seating position in your vehicle has a specificsafety belt assembly which is made up of one buckle and onetongue that are designed to be
2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.Safety belt with cinch tongue (front and rear center seat only)The cinch t
3. Insert the belt tongue into the proper buckle for your seating positionuntil you hear a snap and feel it latch.4. Make sure the tongue is securely
Pregnant women should alwayswear their safety belt. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips
How to use the automatic locking mode1. Buckle the combination lap andshoulder belt (front safetybelt/buckle shown, rear similar).2. Grasp the shoulde
Safety belt pretensionerThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly against t
Safety belt extension assemblyIf the safety belt is too short when fully extended, a safety belt extensionassembly can be obtained from an authorized
If... Then...The driver’s safety belt is notbuckled before the vehicle hasreached at least 3 mph(5 km/h) and 1-2 minutes haveelapsed since the ignitio
Reasons given... Consider...“I was in a hurry” Prime time for an accident.Belt-Minder威 reminds us to take a fewseconds to buckle up.“Safety belts don’
Deactivating/activating the Belt-Minder姞 feature (Driver only)Note: If you are using MyKey威, the Belt-Minder威 cannot be disabled.Also, if the Belt-Min
Door ajar (RTT): Displays whenthe ignition is in the on position andany door is not completely closed.Engine coolant temperature(RTT): Illuminates whe
4. Within seven seconds of the light turning on, buckle then unbuckle thesafety belt.• This will disable the Belt-Minder威 feature if it is currently e
WARNING: All occupants of the vehicle, including the driver,should always properly wear their safety belts, even when an airbag supplemental restraint
WARNING: Additional equipment such as snowplow equipmentmay effect the performance of the airbag sensors increasing therisk of injury. Please refer to
How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustainssufficient longitudinal decelera
WARNING: If the air bag has deployed, the air bag will notfunction again and must be replaced immediately. If the airbag is not replaced, the unrepair
WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. See an authorized deal
The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuittha
WARNING: Do not lean your head on the door. The SafetyCanopy威 could injure you as it deploys from the headliner.WARNING: Do not attempt to service, re
• Two crash sensors located on the C-pillar (one on each side)(SuperCab and Crew Cab only).• Crash sensors located on the front doors.• Rollover senso
WARNING: If the Safety Canopy system has deployed, theSafety Canopy will not function again unless replaced. TheSafety Canopy system (including the A,
AdvanceTrac威/Traction control(if equipped): Displays when theAdvanceTrac威/Traction control isactive. If the light remains on, havethe system serviced
Passenger airbag ON/OFF switch (if equipped)WARNING: An airbagON/OFF switch may beinstalled in this vehicle. Beforedriving, always look at the face of
WARNING: An infant in a rear-facing seat faces a high risk ofserious or fatal injuries from a deploying passenger airbag. Rearfacing infant seats shou
WARNING: If your vehicle has rear seats, always transportchildren who are 12 and younger in the rear seat. Always usesafety belts and child restraints
2. Child age 1 to 12. A child age 1 to 12 must ride in the front seatbecause:• the vehicle has no rear seat;• although children ages 1 to 12 ride in t
Transport Canada deactivation criteria (Canada Only)1. Infant: An infant (less than 1 year old) must ride in the front seatbecause:• my vehicle has no
Disposal of airbags and airbag equipped vehiclesSee authorized dealer. Airbags MUST BE disposed of by qualifiedpersonnel.SAFETY RESTRAINTS FOR CHILDRE
Recommendations for Safety Restraints for ChildrenChild size, height, weight, orageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb
Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe
WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli
Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle.If the child is the proper height, age, and weigh
Locks and Security 130Keys 130Locks 138Anti-theft system 150Seating and Safety Restraints 154Seating 154Safety restraints 169Airbags 180Child restrain
Speed control (if equipped): Thespeed control system indicator lightchanges color to indicate what modethe system is in:• On (amber light): Illuminate
Installing child safety seats with automatic locking modecombination lap and shoulder belts (front passenger and rearoutboard seating positions)Check
1. Position the child safety seat in aseat with a combination lap andshoulder belt.WARNING: An airbag can kill or injure a child in a child seat.Child
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up
Note: Although the child seat illustrated is a forward facing child seat,the steps are the same for installing a rear facing child seat.1. Position th
4. Insert the belt tongue into theproper buckle for that seatingpositions until you hear a snap andfeel it latch. Make sure the tongue issecurely latc
7. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the
The tether strap anchors in your vehicle are in the following positions(shown from top view):• F-Series Regular Cab• F-Series SuperCab• F-Series Crew
Once the child safety seat has been installed using the safety belt, youcan attach the top tether strap.Tether strap attachment1. Route the child safe
• Rear seats (Crew Cab)If the tether strap is clipped incorrectly, the child safety seat may not beretained properly in the event of a collision.6. Re
GAUGESBase cluster with automatic transmission shown. Metric similar.1. Engine oil pressure gauge: Indicates engine oil pressure. Theneedle should sta
Many tether straps cannot be tightened if the tether strap is hooked tothe loop directly behind the child seat. To provide a tight tether strap:1. Rou
Child booster seatsThe belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child
Booster seats should be used until you can answer YES to ALL of thesequestions when seated without a booster seat:• Can the child sit all the way back
• High back booster seatsIf, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo
If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat may improve thisconditio
WARNING: Failure to inspect and if necessary replace thesafety belt assembly or child restraint system under the aboveconditions could result in sever
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary
• Narrower – to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUVs and
TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen
Yellow area The transmission fluid is higher than normal operatingtemperature. This can be caused by special operation conditions (i.e.snowplowing, to
Glossary of Tire Terminology• Tire label: A label showing the OE (Original Equipment) tire sizes,recommended inflation pressure and the maximum weight
Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure of all tires and adjust ifrequired
Maximum Permissible Inflation Pressure is the tire manufacturer’smaximum permissible pressure and/or the pressure at which themaximum load can be carr
6. Visually inspect the tires to make sure there are no nails or otherobjects embedded that could poke a hole in the tire and cause an airleak.7. Chec
WARNING: Stay out of the trajectory (1) as indicated in theillustration.TIRE CAREInspecting your tires and wheel valve stemsPeriodically inspect the t
Tire wearWhen the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Buil
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w
Safety PracticesWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the tires; spinning the tires can tear the tire andcaus
The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear.Tire rotationRotating your tire
Selectable featuresInfo (information menu)Press the INFO button repeatedly tocycle through the following features:TRIP A/BRegisters the distance of in
• Dual rear wheel (DRW) vehicles –Six tire rotationIf your vehicle is equipped with dualrear wheels it is recommended thatthe front and rear tires (in
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
7. H: Indicates the tire’s speed rating. The speed rating denotes thespeed at which a tire is designed to be driven for extended periods oftime under
10. Tire Ply Composition and Material Used: Indicates the number ofplies or the number of layers of rubber-coated fabric in the tire tread andsidewall
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe
The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw
Understanding your tire pressure monitoring system (TPMS)The tire pressure monitoring system measures pressure in your four roadtires and sends the ti
When you believe your system is not operating properlyThe main function of the tire pressure monitoring system is to warn youwhen your tires need air.
If you calculate your average fuel economy by dividing distance traveledby gallons of fuel used (liters of fuel used by 100 kilometers traveled),your
Low tirepressurewarning lightPossible cause Customer action requiredFlashingwarning lightSpare tire in use Repair the damaged road wheel/tireand reins
TPMS reset procedureThe TPMS reset procedure needs to be performed after each tirerotation on vehicles that require different recommended tirepressure
3. Cycle the ignition to the onposition with the engine off.4. Turn the hazard flashers on thenoff three times. This must beaccomplished within 10 sec
8. Remove the valve cap from the valve stem on the right rear tire;decrease the air pressure until the horn sounds.9. Remove the valve cap from the va
Follow these guidelines when using snow tires and chains:• If possible, avoid fully loading your vehicle.• Use only SAE Class S chains.• Install chain
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
System check and vehicle feature customizationPress the SETUP button repeatedlyto cycle the message center throughthe following features:Note: Some it
WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the
to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400
Towing a trailer places an additional load on your vehicle’s engine,transmission, axle, brakes, tires and suspension. Inspect thesecomponents carefull
Vehicle type Rear axleratioMaximumGCWR - lb (kg)F–250/F–350 Single Rear Wheel (SRW) 3.73 19000 (8617)4.30 22000 (9977)F–350 Dual Rear Wheel (DRW) 3.73
WARNING: The hitch rating listed on the trailer hitch label aremaximum possible trailer ratings for that hitch but may not bewhat your vehicle is capa
Fifth-wheel and gooseneck towingYour vehicle may be equipped with a fifth-wheel prep package. Thispackage enables your vehicle to accept certain fifth
If you use a rental trailer, follow the instructions that the rental agencygives to you.Do not attach safety chains to the bumper.Trailer brakesElectr
The TBC user interface consists ofthe following:1. +/- (GAIN adjustmentbuttons): Pressing these buttonsadjusts the TBC’s power output tothe trailer br
2. Manual control lever: Slide the control lever to the left to activatepower to the trailer’s electric brakes independent of the tow vehicle’sbrakes
trailer wheel lock-up. If towing a heavier trailer, trailer wheel lock-upmay not be attainable even with the maximum GAIN setting of 10.Explanation of
To reset the oil monitoring system to 100% after each oil change,perform the following:1. Press and release the SETUP button to display “OIL LIFE XXX%
• The TBC is equipped with a feature which reduces output at vehiclespeeds below 11 mph (18 km/h) so trailer and vehicle braking is notjerky or harsh.
Your vehicle may be equipped with a temporary or conventional sparetire. If the spare tire is different in size (diameter and/or width), treadtype (Al
Braking• Anticipate stops; allow more distance and time to stop than normal.• Do not apply the trailer brakes for extended periods of time as theycan
RECREATIONAL TOWINGFollow these guidelines if you have a need for recreational (RV) towing.An example of recreational towing would be towing your vehi
WARNING: Never link two straps together with a clevis pin.These heavy metal objects could become projectiles if the strapbreaks and can cause serious
STARTINGPositions of the ignition1. Off— shuts off the engine and allaccessories/locks the steering wheeland allows key removal. Note: Inorder to swit
WARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine compartment and exhaus
• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).3. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning
Note: Cranking may be stopped at any time by turning the key to the offposition.3. After idling for a few seconds, release the parking brake, apply th
If the engine fails to start using the preceding instructions (flexiblefuel vehicles only)1. Press and hold down the accelerator 1/3 to 1/2 way to flo
RESET FOR ZONE SETTINGThis feature changes the compass zone setting.Most geographic areas (zones) have a magnetic north compass point thatvaries sligh
WARNING: To reduce the risk of electrical shock, do not useyour heater with ungrounded electrical systems or two-pronged(cheater) adapters.Prior to us
How to use the engine block heaterEnsure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth.Depending on the type
Brake assistThe brake assist system provides full braking force during panic brakingsituations. It detects a rapid application of the brake pedal and
Parking brakeTo set the parking brake, press theparking brake pedal down until thepedal stops.The BRAKE warning lamp in theinstrument cluster illumina
ENGINE ONLY TRACTION CONTROL (DUAL REAR WHEEL (DRW)VEHICLES ONLY)This system helps you maintain the stability and steerability of yourvehicle, especia
Engine only traction control (DRW only)Button functions TCS OFF indicator TCSDefault at start-up Not illuminated EnabledButton pressedmomentarilyIllum
WARNING: Remember that even advanced technology cannotdefy the laws of physics. It’s always possible to lose control of avehicle due to inappropriate
Note: If the system cannot be turned off, refer to MyKey威 in the Locksand Security chapter for more information.When AdvanceTrac威 with RSC威 performs a
Electronic stability control (ESC)Electronic stability control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa
Switching off AdvanceTrac威 with RSC威If the vehicle is stuck in snow, mud or sand, and seems to lose engine power,switching off certain features of the
5. Press and release the RESET button repeatedly until the correct zonesetting for your geographic location is displayed on the message center.The ran
Trailer sway controlYour vehicle may be equipped with trailer sway control. When properlyequipped, trailer sway control will use the vehicle’s Advance
WARNING: Hill descent control cannot control descent in allsurface conditions and circumstances, such as ice or extremelysteep grades. Hill descent co
Hill descent modes• At speeds below 20 mph (32 km/h): When the HDC switch is pressedand HDC is active, the HDC telltale will flash.• At speeds below 2
If any steering components are serviced or replaced, install newfasteners (many are coated with thread adhesive or have prevailingtorque features whic
For 2WD vehicles and vehiclesequipped with a manual shift4WD system:Turn the control to ON. Theindicator light will display in theinstrument cluster.O
WARNING: Vehicles with a higher center of gravity such asutility vehicles and trucks handle differently than vehicles with alower center of gravity. U
5. Remove the top half of the shroud.6. Remove the three fasteners underthe column that secure the lowershroud half to the column.7. Pull the lock lev
WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your author
R (Reverse)With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Re
WARNING: Do not use the tow/haul feature when driving in icyor slippery conditions as the increased engine braking can causethe rear wheels to slide a
LANGUAGE = ENGLISH / SPANISH / FRENCHAllows you to choose which language the message center will display in.Selectable languages are English, Spanish,
to relearn the normal shift strategy parameters, much like having to resetyour radio stations when your vehicle battery has been disconnected.The adap
To activate tow/haul, press thebutton on the end of the gearshiftlever.The TOW HAUL indicator light willilluminate in the instrument cluster.Tow/haul
To return to normal D (Overdrive) position, move the shift lever backfrom M to D.• The transmission will operate in gears one through six.2 (Second)Us
gear. Example: press the – button twice to lock out 6th and 5th gears.Only the available gears will be displayed and the transmission willautomaticall
once the engine has developed sufficient drive to prevent the vehiclefrom rolling down the slope. This is an advantage when pulling away on aslope; fo
If your vehicle gets stuck in mud or snow, it may be rocked out byshifting between forward and reverse gears, stopping between shifts in asteady patte
The RSS detects obstacles up to6 feet (2 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the fi
Keep the RSS sensors (located on the rear bumper/fascia) freefrom snow, ice and large accumulations of dirt (do not clean thesensors with sharp object
• (1) Rear bumper• (2) Red zone• (3) Yellow zone• (4) Green zone• (5) Centerline of vehicleAlways use caution while backing.Objects in the red zone ar
WARNING: The camera system is a reverse aid supplementdevice that still requires the driver to use it in conjunction withthe rear view mirror and the
Roadside Emergencies 317Getting roadside assistance 317Hazard flasher control 318Fuel pump shut-off 319Fuses and relays 319Changing tires 329Wheel lug
PASSENGER DOOR AJAR — Displayed when the passenger’s door isnot completely closed.REAR LEFT DOOR AJAR — Displayed when the rear left door is notcomple
4WD operation is not recommended on dry pavement. Doing so couldresult in difficult disengagement of the transfer case, increased tire wearand decreas
• auto-manual hub locks can bemanually overridden by rotatingthe hub lock control from AUTOto LOCK if desired.• automatic operation of thehub locks is
2H (2WD) – For general on-road driving. Sends power to the rearwheels only should be used for street and highway driving. Providesoptimal smoothness a
Shifting from 4H (4x4 High) to 2H (2WD)Move the transfer case lever to 2H(2WD) at a stop or a vehicle speedbelow 3 mph (5 km/h).With the vehicle at co
3. Move the transfer case shift leverthrough N (Neutral) directly to 4H(4x4 High) or 2H (2WD).4. If the transfer case will notengage into 4H (4x4 High
4L (4X4 LOW) - Uses extra gearing to provide maximum power to allfour wheels at reduced speeds. Intended only for off-road applicationssuch as deep sa
Note: Some noise may be heard as the system shifts or engages; this isnormal.Note: 4x4 low mode is not intended for use on dry pavement.Driving off-ro
• Be extremely careful when driving on pavement made slippery byloose sand, water, gravel, snow or ice.If your vehicle goes off the edge of the paveme
WARNING: Do not spin the wheels at over 35 mph (56 km/h).The tires may fail and injure a passenger or bystander.Refer to Gauges in the Instrument Clus
WARNING: Always set the parking brake fully and make surethe gearshift is latched in P (Park). Turn the ignition to the offposition and remove the key
TRAIN RIGHT FRONT TIRE (if equipped) — Displayed whentraining the TPMS. Refer to TPMS reset procedure in the Tires, Wheelsand Loading chapter for more
Mud and waterIf you must drive through highwater, drive slowly. Traction orbrake capability may be limited.When driving through water,determine the de
Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should
Should you start to slide while driving on snowy or icy roads, turn thesteering wheel in the direction of the slide until you regain control.Avoid sud
Failure to maintain your vehicle properly may void the warranty, increaseyour repair cost, reduce vehicle performance and operational capabilitiesand
SNOWPLOWINGFord recommends that the Super Duty F-Series used for snow removalinclude the Snow Plow Package Option.Installing the snowplowWeight limits
Operating the vehicle with the snowplow attachedDo not use your vehicle for snow removal until it has been driven atleast 500 miles (800 km).The attac
Transmission operation while plowingOperate the vehicle with the automatic transmission gearshift lever inthe D (Overdrive) position and tow/haul off.
ROADSIDE ASSISTANCEVehicles sold in the U.S. : Getting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany off
U.S. Ford vehicle customers who require Roadside Assistance, call1-800-241-3673.If you need to arrange roadside assistance for yourself, Ford MotorCom
FUEL PUMP SHUT-OFFIn the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fue
VEHICLE NEAR TOP SPEED — Displayed when a MyKey威 is in useand the MyKey speed limit is on and the vehicle speed is approaching80 mph (130 km/h). Refer
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
To remove the fuse panel cover, pullthe panel toward you. When theclips of the panel disengage, let thepanel fall easily.To remove a fuse use the fuse
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Not used (spare)2 15A Upfitter relay #43 30A Not used (spare)4
Fuse/RelayLocationFuse AmpRatingProtected Circuits11 10A Instrument cluster12 15A Interior lighting, Lighted runningboard lamps13 15A Right turn signa
Fuse/RelayLocationFuse AmpRatingProtected Circuits31 5A Trailer brake controller (brakesignal), Customer access32 15A Moon roof, Telescoping mirrorswi
Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot
Fuse/RelayLocationFuse AmpRatingProtected Circuits10 — Not used11 — Not used12 — Not used13 — Not used14 — Not used15 Diode Fuel pump (diesel engine)1
Fuse/RelayLocationFuse AmpRatingProtected Circuits38 Relay Powertrain control module(PCM) (diesel engine),Electronic control module (ECM)(gas engine)3
Fuse/RelayLocationFuse AmpRatingProtected Circuits62 — Not used63 — Not used64 — Not used65 — Not used66 20A** Fuel pump67 — Not used68 10A** Fuel pum
Fuse/RelayLocationFuse AmpRatingProtected Circuits92 20A* Auxiliary power point #493 20A* Auxiliary power point #394 25A* Upfitter #195 25A* Upfitter
TBC GAIN = XX.X NO TRAILER (if equipped) — Displays thecurrent gain setting for the trailer brake when a trailer is not connected.Refer to Trailer tow
WARNING: The use of tire sealants may damage your tirepressure monitoring system (TPMS) and should not be used.However, if you must use a sealant, the
Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following:• Handling, stability and braki
Spare tire informationNote: If your vehicle is equipped the tire pressure monitoring system(TPMS), the system indicator light will illuminate when the
Location of the spare tire and toolsIf your vehicle is equipped with a spare tire, jack and associated tools,refer to the following table for their lo
• Vehicles equipped with dualrear wheels, insert the lugwrench extension into the lugwrench to reach the lug nuts.2. Attach the spare tire lock key (A
If equipped with a tether, perform the following additional steps:6. Lift the spare tire on end toaccess the tether attachment.7. Use the lug wrench t
1. Turn engine off and block thewheel that is diagonally opposite ofthe flat tire using the wheel chock,if equipped. If the vehicle is a4x4, lock the
• Front driver side (4x4)Note: Make sure the jack fits ontothe flat area on the outboard side ofthe differential.• Front passenger side (4x4)Note: Vie
Never use the front or reardifferential as a jacking point.WARNING: To lessen therisk of personal injury, donot put any part of your bodyunder the veh
12. Position the jack according to the following guides:• Front (4x2): F–350 DRWNote: Place jack directly underI-beam.• Front driver side (4x4): F–350
CHECK 4X4 (if equipped) — Displayed when a 4X4 system fault ispresent. For more information, refer to Four-wheel drive (4WD)operation in the Driving c
• Front: F–450/F–550• Rear: F-350 DRW• Rear: F-450/F-55013. Insert the jack handle into thepump linkage.14. Use an up-and-down motionwith the jack han
15. Remove the lug nuts with the lug wrench.16. Replace the flat tire with the spare tire, making sure the valve stemis facing outward on all front an
10–lug nut torque sequence19. Stow the flat tire. Refer to Stowing the flat/spare tire if the vehicleis equipped with a spare tire carrier.20. Stow th
If the ornament retention towers arealigned between the studs/lug nuts,the ornament is improperlyinstalled. This improper installationmay appear and s
4. Be sure to install all the clips on the nuts over the flanges so thatthere is an even gap all around and the retention clips are fully seated.Stowi
5. Turn the jack handle clockwise until the tire is raised to its stowedposition underneath the vehicle. The effort to turn the jack handleincreases s
On all two-piece flat wheel nuts,apply one drop of motor oil betweenthe flat washer and the nut.WARNING: When a wheel is installed, always remove anyc
Do not attempt to push-start your automatic transmissionvehicle. Automatic transmissions do not have push-startcapability. Attempting to push-start a
1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery.2. Connect the other end of thepositive (+) cable to the
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.Note: In the illustration, the vehicle on the bottom i
DRIVER RESUME CONTROL (if equipped) — Displayed when thehill control and off-road mode require the driver to resume control.FOR HILL CNTRL SELECT GEAR
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
Note: Towing an ESOF 4x4 vehicle with the front wheels on the groundwithout disengaging the front hubs may cause damage to the automatictransmission.N
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehi
• Service specials and promotions.In Canada:Mailing addressCustomer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ont
IN CALIFORNIA (U.S. ONLY)California Civil Code Section 1793.2(d) requires that, if a manufactureror its representative is unable to repair a motor veh
procedure outlined earlier in this chapter in the Getting the servicesyou need section, you may be eligible to participate in the BBB AUTOLINE program
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
If your vehicle must be serviced while you are traveling or living inAsia-Pacific Region, Sub-Saharan Africa, U.S. Virgin Islands, CentralAmerica, the
If your vehicle must be serviced while you are traveling or living in theMiddle East, contact the nearest authorized dealer. If the authorizeddealer c
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im
Note: If this message is ignored, your vehicle will continue to fill theDiesel Particulate Filter (DPF) with particles (exhaust soot). If cleaningis n
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i
WAXING• Wash the vehicle first.• Use a quality wax that does not contain abrasives.• Do not allow paint sealant to come in contact with any non-body(l
• Do not spray a hot engine with cold water to avoid cracking theengine block or other engine components.• Spray Motorcraft威 Engine Shampoo and Degrea
• 6.8L V10 gasoline enginePLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your
• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft威 Premium Windshield Washer Concentrate (ZC-32-A) inthe U.S., or Premiu
3. If necessary, apply more soap and water solution or cleaning productto a clean, white, cotton cloth and press the cloth onto the soiledarea–allow t
INTERIORFor fabric, carpets, cloth seats and safety belts:• Remove dust and loose dirt with a vacuum cleaner.• Remove light stains and soil with Motor
LEATHER SEATS FOR THE KING RANCH姞 EDITION ONLY(IF EQUIPPED)Your vehicle is equipped with seating covered in premium, top-grainleather which is extreme
UNDERBODYFlush the complete underside of your vehicle frequently. Keep body anddoor drain holes free from packed dirt.Note: Use care when using a powe
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
STOP SAFELY NOW (diesel engine only) — Displayed and a chimesounds when the vehicle exhaust system temperature exceeds intendedoperating range. If thi
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th
6.2L V8 gasoline engine1. Windshield washer fluid reservoir2. Engine oil dipstick3. Automatic transmission fluid dipstick4. Brake fluid reservoir5. En
6.8L V10 gasoline engine1. Windshield washer fluid reservoir2. Battery3. Automatic transmission fluid dipstick4. Engine oil filler cap5. Engine oil di
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
Poor wiper quality can be improved by cleaning the wiper blades and thewindshield. Refer to Windows and wiper blades in the Cleaningchapter.To prolong
• Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by a service technician.7. Put the dipstick back in
To protect your engine and engine’s warranty, use Motorcraft威 SAE5W-20 or an equivalent SAE 5W-20 oil meeting Ford specificationWSS-M2C945-A. SAE 5W-2
If you see any corrosion on the battery or terminals, remove the cablesfrom the terminals and clean with a wire brush. You can neutralize theacid with
Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe bat
ENGINE COOLANTChecking engine coolantThe concentration and level of engine coolant should be checked at theintervals listed in scheduled maintenance i
ENGINE IDLED SOON EXHAUST FLUID EMPTY (diesel engineonly) — Displayed when the SCR system detects low exhaust fluid. Theengine will eventually enter i
Note: Automotive fluids are not interchangeable; do not use enginecoolant/antifreeze or windshield washer fluid outside of its specifiedfunction and v
• Do not add extra inhibitors or additives to the coolant. Thesecan be harmful and compromise the corrosion protection of the enginecoolant.For vehicl
If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your coolin
If you drive in extremely hot climates:• It is still necessary to maintain the coolant concentrationabove 40%.• NEVER decrease the coolant concentrati
Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to an authorized dealer as soon as possible to minimizeengine damage
WARNING: To reduce the risk of collision and injury, beprepared that the vehicle speed may reduce and the vehicle maynot be able to accelerate with fu
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsWARNING: Do not overfill the fuel tank. The pressure in anoverfilled tank may c
• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek med
WARNING: Flexible fuel components and standard unleadedgasoline fuel components are not interchangeable. If your vehicleis not serviced in accordance
Fuel filler capWhen fueling your vehicle:1. Turn the engine off.2. Carefully turn the filler cap counterclockwise until it spins off.3. Pull to remove
OIL CHANGE REQUIRED — Displayed when the oil life left reaches0%. Refer to the scheduled maintenance information for moreinformation.LOW FUEL PRESSURE
Your vehicle was not designed to use fuel or fuel additives with metalliccompounds, including manganese-based additives.Note: Use of any fuel other th
problems continue, fill the vehicle with regular unleaded gasoline anddrive vehicle normally until gasoline is used. See your authorized dealerif the
ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform
2. Each time you fill the tank, record the amount of fuel added (ingallons or liters).3. After at least three to five tank fill-ups, fill the fuel tan
• Warming up a vehicle on cold mornings is not required and mayreduce fuel economy.• Resting your foot on the brake pedal while driving may reduce fue
EMISSION CONTROL SYSTEMWARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine
Do not make any unauthorized changes to your vehicle or engine. Bylaw, vehicle owners and anyone who manufactures, repairs, services,sells, leases, tr
Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect
POWER STEERING FLUIDCheck the power steering fluid. Refer to scheduled maintenanceinformation. If adding fluid is necessary, use only MERCON威 ATF.• Ga
BRAKE FLUID• Vacuum boost system• Hydroboost systemThe fluid level will drop slowly as the brakes wear, and will rise when thebrake components are rep
Scheduled Maintenance 423Normal scheduled maintenance and log 428Index 443The information contained in this publication was correct at the time of goi
Press the up/down buttons to moveup/down through the messagecenter choices.Press the left/right buttons to moveleft/right through the messagecenter ch
2. Park the vehicle on a level surface and engage the parking brake.3. With the engine running, parking brake engaged and your foot on thebrake pedal,
Correct fluid levelFor vehicles equipped with 5-speed transmissions, the fluid should bechecked at normal operating temperature 150°F-170°F (66°C-77°C
Adjusting automatic transmission fluid levelsBefore adding any fluid, make sure the correct type is used. The type offluid used is normally indicated
TRANSFER CASE FLUID (IF EQUIPPED)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough fluid throughthe fil
The following procedure is for vehicles equipped with a gasoline engine.If your vehicle is equipped with a diesel engine, refer to the dieselsupplemen
5. Release the three clamps thatsecure the cover to the air filterhousing. Push the air filter covertoward the center of the vehicle andup slightly to
10. Reconnect the mass air flowsensor electrical connector to theoutlet tube. Make sure the lockingtab on the connector is in the“locked” position (co
• Cover interior trim to prevent fading.• Keep all rubber parts free from oil and solvents.Engine• The engine oil and filter should be changed prior t
Miscellaneous• Make sure all linkages, cables, levers and pins under vehicle arecovered with grease to prevent rust.• Move vehicles at least 25 feet (
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationFront axle 5.8 pints (2.8L)Motorcraft
Gauge ModeIn this mode, the following options are available in different graphicalformats:• Engine Oil Temperature (diesel only)• Transmission Tempera
Item Capacity Ford part nameFord part number /Ford specificationEngine and fuel coolant- diesel engineRefer to the diesel supplement.Engine oil (inclu
Item Capacity Ford part nameFord part number /Ford specificationHinges, latches, strikerplates, fuel filler doorhinge and seat tracks— Multi-Purpose G
Item Capacity Ford part nameFord part number /Ford specificationWindshield washer fluid Fill as requiredMotorcraft威 PremiumWindshield WasherConcentrat
ENGINE DATAEngine 6.2L V8 engine 6.8L V10 engineCubic inches 378 413Required fuelMinimum 87 octane orEthanol (E85)Minimum 87 octaneFiring order 1-5–4–
6.8L V10 engine - without A/CIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulation
Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX
TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis
FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C
Peace of mind•Keyless entry keypad •Back up alarm*•Remote start •Cable lock*•Vehicle security systems •Bed hooks*•Wheel locks •Tool/Cargo boxes*•Prote
FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 32 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the
If you calculate your average fuel economy by dividing miles traveled bygallons of fuel used (liters of fuel used by 100 kilometers traveled), yourfig
Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With
Ford Extended Service Plan4212012 F-250/350/450/550 (f23)Owners Guide, 2nd PrintingUSA (fus)
FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is
GENERAL MAINTENANCE INFORMATIONThe following information pertains to 6.2L V8 and 6.8L V10 gasolineengines only. Scheduled maintenance for the diesel e
Ford strongly recommends the use of genuine Ford replacement parts.Parts other than Ford, Motorcraft威 or Ford-authorized remanufacturedparts that are
Genuine Ford and Motorcraft姞 replacement partsDealerships stock Ford and Motorcraft威 branded replacement parts.These parts meet or exceed Ford Motor C
Check every monthEngine oil levelFunction of all interior and exterior lightsTires for wear and proper pressure, including spareWindshield washer flui
Multi-point inspection – Recommended each visitAccessory drive belt(s) Half-shaft dust boots (if equipped)Battery performance Horn operationClutch ope
NORMAL SCHEDULED MAINTENANCE AND LOGThe following section contains the “Normal Schedule”. This schedule ispresented at specific mileage (kilometer) in
6.2L and 6.8L enginesMiles (x 1,000)* 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75Kilometers (x 1,000)* 12 24 36 48 60 72 84 96 108 120Months* 6 12 18 24 30
Truck Apps (if equipped)In this mode, off-road and trailer towing application options are available.Off Road*Pitch and bank angle (in degrees). Displa
6.2L and 6.8L enginesMiles (x 1,000)* 82.5 90 97.5 105 112.5 120 127.5 135 142.5 150Kilometers (x 1,000)* 132 144 156 168 180 192 204 216 228 240Month
6.2L and 6.8L enginesEvery 15,000 miles(24,000 km)Replace cabin air filter (if equipped)Every 30,000 miles(48,000 km)Replace climate-controlled seat f
Maintenance schedule logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDAT
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
SPECIAL OPERATING CONDITIONSThe following information pertains to 6.2L V8 and 6.8L V10 gasolineengines only. Scheduled maintenance for the diesel engi
Extensive idling and/or low-speed driving for long distances asin heavy commercial use (i.e. delivery, taxi, patrol car or livery)Inspect frequently,s
Operating in dusty conditions such as unpaved or dusty roadsInspect frequently,service as requiredReplace cabin air filter (if equipped)Replace engine
Off-road operationInspect frequently,service as requiredInspect steering linkage, ball joints and U-joints;lubricate if equipped with grease fittingsR
Special operating condition logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER
When “Press OK for options” is displayed, pressing OK will open thetrailer options menus:Trailer*Change ActiveTrailerWhen this is highlighted, press t
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
EXCEPTIONSThere are several exceptions to the Normal Schedule. They are listedbelow:Normal vehicle axle maintenance: Rear axles and power take-off(PTO
Edge/MKX AWD only – vehicles operating off-road in sand during highambient temperatures must replace the AWD PTU (All-wheel drivePower Transfer Unit)
AAccessory delay ...105AdvanceTrac ...275Airbag supplemental restraintsystem ...1
LATCH ...206recommendations ...197Child safety seats - boosterseats ...
Engine oil ...374checking and adding ...374dipstick ...374filter, specifica
Infant seats(see Safety seats) ...199Inspection/maintenance (I/M)testing ...397Instrument panel
PParental MyKeyprogramming ...130Parking brake ...273Parts(see Motorcraft威 parts) ...408Ped
Servicing your vehicle ...369Setting the clock ...61, 63Snowplowing ...7, 314–315SOS Post Crash Alert ...
Washer fluid...373Water, Driving through...313Windowspower...104Windshield wa
Trailer*Rename Trailer Press the right arrow button when this is highlightedto display saved or default trailers. Use the up/downbuttons to highlight
Determine which magnetic zone youare in for your geographic locationby referring to the zone map.Vehicle* (cont’d)Compass(cont’d)Calibration (When cho
MyKeyCreate MyKey Hold OK to create MyKey*AdvanceTrac Always on or Selectable*MAX Speed 80 MPH (120 km/h) or Off*Speed Warning 45, 55 or 65 MPH (75, 9
System Check*Trailer SwayPark Aid Check Rear Park AidFuel Level (distance to empty)* If equipped—your vehicle may be equipped with some or all of thes
DOOR AJAR — Displayed when the door is not completely closed.DRIVER DOOR AJAR — Displayed when the driver door is notcompletely closed.LEFT REAR DOOR
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
POWER REDUCED TO LOWER ENGINE TEMP — Displayed whenthe engine temperature gauge needle moves to H. You may noticereduced engine power. Refer to Engine
STOP SAFELY NOW, the chime will sound, and engine power will bereduced again and shut down below 3 mph (5 km/h). Refer to yourdiesel supplement for mo
EXHAUST FILTER CLEANED (diesel engine only) — Displayedwhen the Diesel Particulate Filter (DPF) has been adequately cleaned bythe manual regeneration
IN XX MILES, SPEED LIMITED TO 50 MPH EXHAUST FLUIDSYSTEM FAULT (diesel engine only) — Displayed when the SCRsystem detects a fault. The vehicle’s top
• Low Fuel Operation: If the message appears when the vehicle is warmand during low fuel tank level operation, i.e. the tank level is at orvery near e
TRAIN INNER LEFT REAR TIRE — Displayed when training theTPMS. Refer to TPMS reset procedure in the Tires, Wheels andLoading chapter for more informati
4X4 SHIFT IN PROGRESS (if equipped) — Displayed when the 4X4system is making a shift. For further information, refer to Four-wheeldrive (4WD) operatio
FOR HILL DESCENT REDUCE SPEED (if equipped) — Displayedwhen the vehicle speed requirement for off-road mode entry has notbeen met.FOR HILL DESCENT SEL
COULD NOT PROGRAM INTEGRATED KEY — Displayed when anattempt is made to program a fifth integrated key to the remote keylessentry system. For more info
TO STOP ALARM, START VEHICLE (if equipped) — Displayedwhen the perimeter alarm system is armed and the vehicle is enteredusing the key on the driver’s
Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti
AUDIO SYSTEMSAM/FM stereo system (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strong
1. / (Tuner): Press tomanually go up or down the radiofrequency. Press and hold for a fastadvance through radio frequencies.Also use in AUDIO mode to
6. ON/OFF/Volume: Press VOL -PUSH to turn ON/OFF. Turn VOL -PUSH to increase/decrease volume.7. CLK (Clock): Press CLK totoggle between the clock and
Accessory delay: Your vehicle is equipped with accessory delay whichallows you to operate the window switches and the audio for up to10 minutes after
• SAVE SONG: Press OK to save the currently playing song title in thesystem’s memory. (If you try to save something other than a song,CANT SAVE will a
When the six strongest stations are filled, the station stored in preset 1will begin playing. If there are less than six strong stations, the systemwi
Use / / SEEK, SEEK to toggle ON/OFF. When COMPRESSis ON, the system will bring the soft and loud CD passages together for amore consistent listening l
7. SHUFFLE:In CD/MP3 mode,press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engage shuffle mode right away, pr
In satellite radio mode (if equipped), press and release to enterTEXT MODE and display the current song title. While in TEXT MODE,press again to scrol
Auxiliary input jack (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommend
Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance
5. Turn the portable music player on and adjust the volume to 1/2 thevolume.6. Press AUX on the vehicle radio repeatedly until LINE, LINE IN orSYNC LI
Your vehicle may be equipped with aUSB port located on the instrumentpanel. This feature allows you toplug in media playing devices,memory sticks, and
• Wipe discs from the center out.Don’t:• Expose discs to direct sunlight or heat sources for extended periodsof time.• Clean using a circular motion.C
Audio system warranty and serviceRefer to the Warranty Guide/Customer Information Guide for audiosystem warranty information. If service is necessary,
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio forthe selectedchannel.No action required. Thisme
Radio Display Condition Action RequiredNO TEXT Categoryinformation notavailable.Category information notavailable at this time onthis channel. The sys
SINGLE ZONE CLIMATE CONTROL1.Defrost: Distributes outside air through the windshield defrostervents and de-mister vents. Can be used to clear the wind
5. Recirculated air (if equipped): Press to activate/deactivate airrecirculation in the vehicle. Recirculated air may reduce the amount oftime needed
Using your vehicle as an ambulanceIf your light truck is equipped with the Ford Ambulance PreparationPackage, it may be utilized as an ambulance. Ford
If you are driving during extreme high ambient temperatures and idlingfor extended periods of time in gear, it is recommended to run the A/Cin the MAX
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Optional or Standard mes
4. Manual control: Allows you to manually select where airflow isdirected. To return to full automatic control, press AUTO. Whenchoosing to control ai
10. Passenger temperature: Turn to increase/decrease the airtemperature on the passenger side of the vehicle. The recommendedinitial setting is betwee
• To improve the A/C cool down, drive with the windows slightly openfor 2-3 minutes after start up or until the vehicle has been “aired out”.• A small
Ensure that the ignition on. Press to turn the defroster on/off. Theindicator light will illuminate when activated. For vehicles with a slidingrear wi
Automatic climate controlFor hot weather conditions:• The interior cabin will be set to 72°F (22°C).• The cooled seats (if equipped) will be set to hi
HEADLAMP CONTROLRotate the headlamp controlclockwise to the first positiontoturn on the parking lamps.Rotate clockwise to the secondpositionto also tu
4. Turn the headlamp control to the autolamp position. The headlampswill turn on.5. Wait the desired amount of time for the exit delay you want (up to
Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the on position,• the head
Event Data RecordingThis vehicle is equipped with an event data recorder (EDR). Themain purpose of an EDR is to record, in certain crash or nearcrash-
Vertical aim adjustmentThe headlamps on your vehicle can only be vertically adjusted. Yourvehicle does not require horizontal aim adjustments.To adjus
TURN SIGNAL CONTROLThe turn signal lever does not mechanically lock in the upward ordownward position when activated. The turn signal control activati
Rear dome/map lampsYour vehicle may have map lampswithin the rear dome lamp. Pressthe switches on either side of thedome lamp to turn the lamps on.BUL
Replacing exterior bulbsCheck the operation of all the bulbs frequently.Function Numberof bulbsTrade numberHeadlamps 2 H13/9008Park/Turn lamp 2 3157NA
Replacing headlamps, park lamps, turn lamps1. Make sure that the exterior lamps are off, then open the hood.2. Using masking tape or a marker,make an
10. For the headlamp bulb, removethe bulb by turning itcounterclockwise and pulling itstraight out.11. For the park or turn lamp bulb,remove the bulb
Install the new bulb(s) in reverse order.Replacing brake/tail/turn/back-up lamp bulbs (chassis cabs only)(if equipped)1. Make sure the headlamps are o
Replacing front clearance and identification lamp bulbs(if equipped)1. Make sure the headlamps are off.2. Remove the screw and lens fromthe lamp assem
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT/TELESCOPE STEERING WHEELTo adjust the steering wheel:1. Pull the lever down to unlock thesteering column.2. While the lever is in the downpositio
Commentaires sur ces manuels