Introduction 5Instrument Cluster 14Warning lights and chimes 14Gauges 21Message center 22Entertainment Systems 60AM/FM stereo 60AM/FM stereo with CD 6
Note: Including to the extent that any law pertaining to EventData Recorders applies to SYNC威 or its features, please note thefollowing: Once 911 Assi
OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehicle’s overhead console will vary according toyour option package.Storage compartment (if equi
• Two removable front cupholdermodules• Removable false bottom tray foraccessing hidden storagecompartment (also has space fora large cup)WARNING: Use
To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe ba
The power point can switch to a fault mode when it is overloaded,overheated, or shorted. For overloading and shorting conditions, unplugyour device an
One-touch downAllows the driver’s window to open fully without holding the controldown. Press the switch completely down to the second detent andrelea
INTERIOR MIRRORThe interior rearview mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side.W
EXTERIOR MIRRORSPower side view mirrors (if equipped)WARNING: Do not adjust the mirror while the vehicle is inmotion.To adjust your mirrors:1. Rotate
Fold-away mirrorsFold the side mirrors in carefully before driving through a narrow space,like an automatic car wash.Power-fold mirrors (if equipped)Y
Note: Ten or more switch activations within one minute, or repeatedfold/unfolding of the mirrors while holding the switch rearward during thefull trav
• To telescope the mirrors inboard, press and hold the right side of thepower telescope switch until the mirrors reach their desired position.Memory m
CELL PHONE USEThe use of mobile communications equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri
POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is
CNCL (Cancel)/RSM (Resume):Press to cancel or resume a setspeed.ON/OFF: Press to turn the systemon or off.– SET +: Press to set a speed or todecrease
Increasing speed while using speed controlTo increase the set speed:• Press and hold SET + until you get to the desired speed, then release.You can al
Navigation system hands freecontrol features (if equipped)Press and hold VOICE briefly untilthe voiceicon appears on thenavigation display to use the
For further information on the Navigation system/SYNC威 system, refer tothe Navigation System and SYNC威 supplements.UPFITTER CONTROLS (IF EQUIPPED)Your
There will also be one power leadfor each switch found as a blunt-cutand sealed wire located below theinstrument panel and to the left ofthe steering
To open the moon roof: Press andrelease the SLIDE control and themoon roof will open automatically tothe “comfort” position. Press andrelease again to
Note: Make sure you keep the original remote control transmitter foruse in other vehicles as well as for future system programming.Note: We recommend
If you do not know if your garagedoor opener is a rolling code orfixed code device, open your garagedoor opener’s remote control batterycover. If a pa
2. Press and hold the outer twobuttons for 1–2 seconds, thenrelease.Note: You may need a ladder toreach the unit and you may need toremove the cover o
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
Fixed code programmingNote: It may be helpful to have another person assist you inprogramming the transmitter.To program units with fixed codeDIP swit
7. When the garage door moves, release the button within one second.When the button is released, the LED lamp will flash slowly.8. The LED lamp will b
POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)WARNING: Always use floor mats that are designed to fit thefoot well of your vehicle. Only use floor mats th
WARNING (Continued)• To install floor mats, position the floor mat so that the eyelet is overthe retention post and press down to lock in.• To remove
3. Partially lower tailgate and carefully feed tailgate harness up throughthe gap between the pickup box and the bumper. Place the tailgateharness out
3. Rotate the center molding tounlatch the tailgate step and pull ittowards you to extend it.4. Flip open the step panel to widenthe step.Note: To red
Bed extender (if equipped)Your vehicle may be equipped with a cargo management feature in thetruck bed.Note: This feature is not intended for off-road
4. Connect the two panels, then rotate both knobs a quarter-turnclockwise to secure the panels.5. Ensure the latch rod is insertedinto the tailgate ho
To open the bed extender into grocery mode, follow Steps 1–4 byrotating the panels away from the tailgate. Close the tailgate.Driver Controls1282012 F
KEYSYour vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
MyKey威 restricted featuresStandard settings – These settings cannot be changed•The audio system will be muted whenever Belt-Minder威 is activateduntil
For optional message center:1. At the main menu screen select SETTING then MYKEY by pressingOK or the right arrow key.2. Press OK to select CREATE MYK
For optional message center:1. At the main menu screen select SETTING then MYKEY by pressingOK or the right arrow key.2. Use the up and down arrows to
Using MyKey威 with remote start systemsMyKey威 is not compatible with non Ford-approved aftermarket remotestart systems. If you choose to install a remo
Note: For all vehicles, the number of MYKEY(S) PROGRAMMED orADMIN KEYS PROGRAMMED that is displayed in the MyKey威 systemstatus menus will include the
TroubleshootingCondition Potential CausesCan’t create a MyKey威 • Key in the ignition is already aMyKey威.• Key in the ignition is the lastremaining adm
Condition Potential CausesI accidentally programmed allkeys as MyKeys威• Vehicle has a non Ford-approvedremote start system that is recognizedas an adm
POWER DOOR LOCKS (IF EQUIPPED)Press control to unlock all doors.Press control to lock all doors.Smart locks (if equipped)This feature prevents you fro
The autolock feature repeats when:• any door is opened then closed while the ignition is in the on positionand the vehicle speed is 9 mph (15 km/h) or
Keyless entry keypad autolock enable/disable procedure1. Turn the ignition to the offposition.2. Close all the doors.3. Enter factory–set 5–digit entr
WARNING LIGHTS AND CHIMESBase instrument cluster with standard measure shown; metricsimilarOptional instrument cluster with standard measure shown; me
Power door lock switch autounlock enable/disable procedureBefore starting, ensure the ignition is in the off position and all vehicledoors are closed.
CHILD SAFETY LOCKS (IF EQUIPPED)• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outsi
The typical operating range for your IKT is approximately 33 feet(10 meters). A decrease in operating range could be caused by:• weather conditions,•
holding both the and buttons simultaneously on the remote entrytransmitter for approximately four seconds. The hazard lamps will flashtwice to indicat
2. Press and hold control button 1for five seconds. A tone will beheard after two seconds confirmingmemory position has been set.Continue to hold unti
4. Insert the new battery. Refer to the instructions inside the IKT for thecorrect orientation of the battery. Press the battery down to ensure thatth
Remote start (if equipped)Your vehicle may be equipped with the remote start feature which allowsyou to start the engine from outside the vehicle. If
The power windows will be inhibited during the remote start and theradio will not turn on.The parking lamps will remain on and the engine will run for
Programming a personal entry code and keypad association tomemory featureTo create your own personal entry code:1. Enter the factory set code.2. Withi
The anti-scan feature will turn off after:• one minute of keypad inactivity.• pressing thecontrol on the remote entry transmitter.• the ignition is tu
bulb works. If any light remains on after starting the vehicle, refer to therespective system warning light for additional information.Standard messag
Automatic armingThe vehicle is armed immediately after turning the ignition off.Automatic disarmingSwitching the ignition on with a coded key disarms
3. After three seconds but within 10 seconds of removing the first codedkey, insert the second previously programmed coded key into theignition and tu
There is a 20 second countdown when any of the above actions occurbefore the vehicle becomes armed.Each door and the hood is armed individually, and i
FRONT SEATSWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the eve
The adjustable head restraintsconsist of :• a trimmed energy absorbing foamand structure (1),• two steel stems (2),• a guide sleeve adjust/releasebutt
To reinstall the adjustable head restraint, do the following:1. Insert the two stems (2) into theguide sleeve collars.2. Push the head restraint downu
Front row center non-adjustable head restraint (if equipped)Vehicle’s equipped with a front center seat will have head restraints thatare non-adjustab
WARNING: The non-adjustable head restraint is a safety device.It should be installed whenever the seat is occupied.WARNING: To minimize the risk of ne
20 percent front seat armrest and console (if equipped)To release the armrest and gainaccess to the cupholders andseatback storage bin, press thebutto
The under-seat storagecompartment (if equipped) has aprogrammable lock. Use the ignitionkey to program the lock to thecompartment. Electronics may bep
WARNING: Under engine misfire conditions, excessive exhausttemperatures could damage the catalytic converter, the fuelsystem, interior floor coverings
Power recline (if equipped)Press the control to recline theseatback forward or rearward.Using the power lumbar support (if equipped)The power lumbar c
Heated and cooled seats (if equipped)The controls for the climate controlled seats are located on the climatecontrol system.Heated SeatsWARNING: Perso
Climate controlled seats air filter replacement (if equipped)The heated and cooled seat system includes air filters that must bereplaced periodically.
To install a filter:1. First, position the filter in itshousing making sure that the farforward end is all the way up in thehousing.2. Push in on the
Easy-access/easy-out feature (if equipped)The easy entry feature can be turned off or on through the vehiclemessage center. Refer to Message center in
Outboard head restraints (CrewCab)Center head restraint (Crew Cab)The non-adjustable second row head restraints consist of :• a trimmed energy absorbi
Folding Up the Rear Seats (SuperCab)1. Pull the control to release theseat cushion.2. Rotate the seat cushion up until itlocks into the vertical stora
Returning the Seat to the Seating PositionWARNING: Make sure that cargo or any objects are not trappedunderneath the seat cushion before returning the
To remove the storage space divider,squeeze the sides and lift it from thestorage tub.Use your vehicle key to lock thestorage space.SAFETY RESTRAINTSW
WARNING: It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision, people riding inthese areas are more likely
WARNING: Driving a vehicle with the brake system warninglight on is dangerous. A significant decrease in brakingperformance may occur. It will take yo
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
1. To lengthen the lap belt, pullsome webbing out of the shoulderbelt retractor.2. While holding the webbing belowthe tongue, grasp the tip (metalport
While you are fastened in the safety belt, the combination lap/shoulderbelt with a cinch tongue adjusts to your movement. However, if youbrake hard, t
Automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt
WARNING: BELT AND RETRACTOR ASSEMBLY MUST BEREPLACED if the safety belt assembly “automatic lockingretractor” feature or any other safety belt functio
Safety belt height adjustmentYour vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shoulder b
Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occup
If... Then...The driver’s safety belt isbuckled before the ignitionswitch is turned to the onposition...The Belt-Minder威 feature will notactivate.The
Reasons given... Consider...“The people I’m with don’twear belts”Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE peop
WARNING: While the design allows you to deactivate yourBelt-Minder威, this system is designed to improve your chances ofbeing safely belted and survivi
Door ajar (RTT): Displays whenthe ignition is in the on position andany door is not completely closed.Engine coolant temperature(RTT): Illuminates whe
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right
WARNING: Never place your arm over the airbag module as adeploying airbag can result in serious arm fractures or otherinjuries.To properly position yo
WARNING: An infant in a rear-facing seat faces a high risk ofserious or fatal injuries from a deploying passenger airbag. Rearfacing infant seats shou
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
• Safety Canopy威 System (if equipped). Refer to Safety Canopy威System later in this chapter.• one or more impact and safing sensors,• a readiness light
How does the side airbag system work?The design and development of theside airbag system includedrecommended testing proceduresthat were developed by
The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces were not of
WARNING: All occupants of the vehicle including the drivershould always wear their safety belts even when an airbag SRSand Safety Canopy威 System is pr
The Safety Canopy system, in combination with safety belts, can helpreduce the risk of severe injuries in the event of a significant side impactcollis
Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref
AdvanceTrac威/Traction control(if equipped): Displays when theAdvanceTrac威/Traction control isactive. If the light remains on, havethe system serviced
Passenger airbag ON/OFF switch (if equipped)WARNING: An airbagON/OFF switch may beinstalled in this vehicle. Beforedriving, always look at the face of
Turning the passenger airbag back onThe passenger airbag remains off until you turn it back on.1. Insert the ignition key and turnthe switch to ON.2.
WARNING: If your vehicle has rear seats, always transportchildren who are 12 and younger in the rear seat. Always usesafety belts and child restraints
2. Child age 1 to 12. A child age 1 to 12 must ride in the front seatbecause:• the vehicle has no rear seat;• although children ages 1 to 12 ride in t
2. Child age 12 or under: A child age 12 or under must ride in thefront seat because:• my vehicle has no rear seat;• although children age 12 and unde
SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme
Recommendations for Safety Restraints for ChildrenChild size, height, weight, orageRecommendedrestraint typeSmallchildrenChildren who have outgrown or
Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe
WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli
Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle.If the child is the proper height, age, and weigh
Locks and Security 129Keys 129Locks 137Anti-theft system 149Seating and Safety Restraints 153Seating 153Rear seats 166Safety restraints 168Airbags 180
Speed control (if equipped): Thespeed control system indicator lightchanges color to indicate what modethe system is in:• On (amber light): Illuminate
Installing child safety seats with automatic locking modecombination lap and shoulder belts (front passenger and rearoutboard seating positions)Check
Installing the child safety seatPerform the following steps when installing the child seat in theoutboard combination lap/shoulder belts:Note: Althoug
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up
Installing child safety seats in cinch tongue combination lap andshoulder belt seating positions (All front center and Super/Crewcab rear center posit
3. While holding both shoulder andlap portions next to the tongue,route the tongue and webbingthrough the child seat according tothe child seat manufa
6. Attach the tether strap (if the child seat is equipped). Refer toAttaching child safety seats with tether straps later in this chapter.7. Before pl
The SuperCab rear seat has three straps behind the top of the seat backthat function as both routing loops for the tether straps and anchor loops.The
Attach the tether strap only to the appropriate tether anchor as shown.The tether strap may not work properly if attached somewhere otherthan the corr
5. Clip the tether strap to the anchor as shown.• Front seats (Regular Cab)• Rear seats (Crew Cab)If the tether strap is clipped incorrectly, the chil
GAUGESBase cluster with automatic transmission shown. Metric similar.1. Engine oil pressure gauge: Indicates engine oil pressure. Theneedle should sta
Tether strap attachment (rear SuperCab only)There are three loops of webbing just above the back of the rear seat(along the bottom edge of the rear wi
3. Install the child safety seat tightlyusing the vehicle belts. Follow theinstructions in this chapter.4. Tighten the tether strapaccording to the ch
When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the
Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
VEHICLE CHARACTERISTICSFour-wheel drive (4WD) system (if equipped)A vehicle equipped with 4WD (when selected) has the ability to use allfour wheels to
How Your Vehicle Differs from Other VehiclesSUVs and trucks can differ fromsome other vehicles in a fewnoticeable ways. Your vehicle maybe:• Higher –
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli
Yellow area The transmission fluid is higher than normal operatingtemperature. This can be caused by special operation conditions (i.e.snowplowing, to
Temperature A B CWARNING: The temperature grade for this tire is establishedfor a tire that is properly inflated and not overloaded. Excessivespeed, u
• PSI: Pounds per square inch, a standard unit of air pressure.• Cold inflation pressure: The tire pressure when the vehicle hasbeen stationary and ou
You are strongly urged to buy a reliable tire pressure gauge, as automaticservice station gauges may be inaccurate. Ford recommends the use of adigita
When weather temperature changes occur, tire inflation pressures alsochange. A 10°F (6°C) temperature drop can cause a corresponding dropof 1 psi (7 k
Tire Inflation InformationWARNING: An inflated tire and rim can be very dangerous ifimproperly used, serviced or maintained. To reduce the risk ofseri
WARNING: Stay out of the trajectory (1) as indicated in theillustration.TIRE CAREInspecting your tires and wheel valve stemsPeriodically inspect the t
Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w
Safety PracticesWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the tires; spinning the tires can tear the tire andcaus
Selectable featuresInfo (information menu)Press the INFO button repeatedly tocycle through the following features:TRIP A/BRegisters the distance of in
Tire RotationWARNING: If the tire label shows different tire pressures forthe front and rear tires and the vehicle is equipped with TPMS(tire pressure
• Dual rear wheel (DRW) vehicles –Six tire rotationIf your vehicle is equipped with dualrear wheels it is recommended thatthe front and rear tires (in
INFORMATION CONTAINED ON THE TIRE SIDEWALLBoth U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the
5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new tires to match the new wheeldiameter
8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n
13. Maximum Permissible Inflation Pressure: Indicates the tiremanufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED)WARNING: The tire pressure monitoring system is NOT asubstitute for manually checking tire pressur
replacement or alternate tires or wheels on the vehicle that prevent theTPMS from functioning properly. Always check the TPMS malfunctiontelltale afte
To restore the full functionality of the tire pressure monitoring system,have the damaged road wheel/tire repaired and remounted on yourvehicle. For a
If you calculate your average fuel economy by dividing distance traveledby gallons of fuel used (liters of fuel used by 100 kilometers traveled),your
Low tirepressurewarning lightPossible cause Customer action requiredFlashing warninglightSpare tire in use Repair the damaged road wheel/tireand reins
TPMS Reset ProcedureWARNING: To determine the required pressure(s) for yourvehicle, refer to the Safety Compliance Certification Label(affixed to eith
3. Cycle the ignition to the onposition with the engine off.4. Turn the hazard flashers on thenoff three times. This must beaccomplished within 10 sec
7. Remove the valve cap from the valve stem on the right front tire;decrease the air pressure until the horn sounds.8. Remove the valve cap from the v
Follow these guidelines when using snow tires and chains:• If possible, avoid fully loading your vehicle.• Use only SAE Class S chains.• Install chain
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei
• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
System check and vehicle feature customizationPress the SETUP button repeatedlyto cycle the message center throughthe following features:Note: Some it
WARNING: Do not use replacement tires with lower loadcarrying capacities than the original tires because they maylower the vehicle’s GVWR and GAWR lim
• A final example for your vehicle with 1,400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the
TRAILER TOWINGNote: The trailer towing chart in this section applies to vehiclesequipped with a gasoline engine; for vehicles equipped with a dieselen
WARNING: Towing trailers beyond the maximum recommendedgross trailer weight exceeds the limit of the vehicle and couldresult in engine damage, transmi
To determine which trailer hitch your vehicle is equipped with, refer tothe trailer hitch label located on trailer hitch cross tube. Once youdetermine
Fifth-wheel trailer hitch (if equipped)To find the maximum trailer weight allowed for your vehicle, consultyour authorized dealer (or the RV and Trail
Safety ChainsNote: Do not attach safety chains to the bumper.Always connect the trailer’s safety chains to the frame or hook retainersof the vehicle h
The TBC user interface consists ofthe following:1. +/- (GAIN adjustmentbuttons): Pressing these buttonsadjusts the TBC’s power output tothe trailer br
2. Manual control lever: Slide the control lever to the left to activatepower to the trailer’s electric brakes independent of the tow vehicle’sbrakes
Explanation of instrument cluster warning messages:The TBC interacts with the instrument cluster message center to displaythe following messages:TRAIL
2. Press and hold the RESET button for two seconds and release to resetthe oil life to 100%.Note: To change oil life 100% value (if equipped with this
• The TBC interacts with the brake system of the vehicle, includingABS, in order to reduce the likelihood of trailer wheel lock-up;therefore, if these
Your vehicle may be equipped with a temporary or conventional sparetire. If the spare tire is different in size (diameter and/or width), treadtype (Al
Braking• Anticipate stops; allow more distance and time to stop than normal.• Do not apply the trailer brakes for extended periods of time as theycan
RECREATIONAL TOWINGFollow these guidelines if you have a need for recreational (RV) towing.An example of recreational towing would be towing your vehi
WARNING: Never link two straps together with a clevis pin.These heavy metal objects could become projectiles if the strapbreaks and can cause serious
STARTINGPositions of the ignition1. Off— shuts off the engine and allaccessories/locks the steering wheeland allows key removal. Note: Inorder to swit
WARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine compartment and exhaus
2. Make sure the headlamps and electrical accessories are off.• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).3. Turn the
the 4 (start) position, the engine may continue cranking for up to10 seconds or until the vehicle starts.Note: Cranking may be stopped at any time by
If the engine fails to start using the preceding instructions (flexiblefuel vehicles only)1. Press and hold down the accelerator 1/3 to 1/2 way to flo
Refer to Compass zone/calibration adjustment.ZONE <XX> RESET = CHANGEThe compass heading is displayed as one of N, NE, E, SE, S, SW, W andNW in
WARNING: To reduce the risk of electrical shock, do not useyour heater with ungrounded electrical systems or two-pronged(cheater) adapters.Prior to us
How to use the engine block heaterEnsure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth.Depending on the type
Brake assistThe brake assist system provides full braking force during panic brakingsituations. It detects a rapid application of the brake pedal and
Parking brakeTo set the parking brake, press theparking brake pedal down until thepedal stops.The BRAKE warning lamp in theinstrument cluster illumina
ENGINE ONLY TRACTION CONTROL (DUAL REAR WHEEL (DRW)VEHICLES ONLY)This system helps you maintain the stability and steerability of yourvehicle, especia
Engine only traction control (DRW only)Button functions TCS OFF indicator TCSDefault at start-up Not illuminated EnabledButton pressedmomentarilyIllum
WARNING: Remember that even advanced technology cannotdefy the laws of physics. It’s always possible to lose control of avehicle due to inappropriate
Note: If the system cannot be turned off, refer to MyKey威 in the Locksand Security chapter for more information.When AdvanceTrac威 with RSC威 performs a
Electronic stability control (ESC)Electronic stability control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa
Switching off AdvanceTrac威 with RSC威If the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off certain features of the
Perform compass calibration in an open area free from steel structuresand high voltage lines. For optimum calibration, turn off all electricalaccessor
AdvanceTrac威 with RSC威 Features (SRW only)Button functionsStabilitycontrollightRSC威 ESC TCSButton pressed againafter deactivationNotilluminatedEnabled
Disabling trailer sway controlTrailer sway control can be disabled during any key cycle. See trailersway control under the Message center in the Instr
Enabling hill descent control and setting the descent speed1. Press and release the hill descentbutton located on the instrumentpanel. A light in the
• Some noise is normal during operation. If excessive, check for lowpower steering pump fluid level before seeking service by your dealer.• Heavy or u
• On 2WD vehicles and 4WD vehicles in 2H (4X2) or 4H (4X4 High),the ELD will automatically disengage at speeds above 25 mph(40 km/h) and will automati
PREPARING TO DRIVEWARNING: Utility vehicles have a significantly higher rolloverrate than other types of vehicles.WARNING: In a rollover crash, an unb
If the fuse is not blown and the brake lamps are working properly, thefollowing procedure will allow you to move the gearshift lever from P (Park):1.
WARNING: Do not drive your vehicle until you verify that thebrake lamps are working.WARNING: When doing this procedure, you will be taking thevehicle
To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)WARNING: Always set the parking b
To deactivate the tow/haul feature and return to normal driving mode,press the button on the end of the gearshift lever. The TOW HAUL lightwill no lon
System warningsSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems.In the event of a multiple warning si
Understanding the shift positions of the 6–speed automatictransmission (if equipped)This vehicle is equipped with an adaptive transmission shift strat
N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D
To deactivate the tow/haul feature and return to normal driving mode,press the button on the end of the gearshift lever. The tow/haul light willno lon
Understanding your SelectShift Automatic™ transmission (SST)gearshift leverThis vehicle is equipped with a SelectShift Automatic™ transmission(SST) ge
Recommended shift speedsUpshift according to the following chart:Upshifts when accelerating (recommended for best fuel economy)Shift from: Gasoline en
Using hill start assistThe hill start assist feature is activated automatically when the vehicle isstopped on a slope greater than five degrees. The h
REVERSE SENSING SYSTEM (IF EQUIPPED)The reverse sensing system (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when the R (Rev
The RSS detects obstacles up to6 feet (2 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the fi
Keep the RSS sensors (located on the rear bumper/fascia) freefrom snow, ice and large accumulations of dirt (do not clean thesensors with sharp object
• (1) Rear bumper• (2) Red zone• (3) Yellow zone• (4) Green zone• (5) Centerline of vehicleAlways use caution while backing.Objects in the red zone ar
Roadside Emergencies 319Getting roadside assistance 319Hazard flasher control 320Fuel pump shut-off 321Fuses and relays 321Changing tires 331Wheel lug
PARK BRAKE ENGAGED — Displayed when the parking brake is set,the engine is running and the vehicle is driven more than 3 mph(5 km/h). If the warning s
WARNING: The camera system is a reverse aid supplementdevice that still requires the driver to use it in conjunction withthe rear view mirror and the
FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED)WARNING: For important information regarding safe operationof this type of vehicle, see Preparing to dri
The ESOF 4WD system:• provides 4x4 High engagement and disengagement while the vehicle ismoving.• is operated by a rotary control located on the instr
Using a Manual Shift On Stop (MSOS) 4x4 system (if equipped)Note: High shift efforts may be encountered when attempting toshift into and out of 4x4 mo
• Do not shift into 4H (4x4High) with the rear wheelsslipping.• The vehicle should not bedriven in 4X4 High with thehub locks disengaged as thiscondit
Shifting from 4L (4x4 Low) to 4H (4x4 High) or 2H (2WD)1. Bring the vehicle to a stop or a speed below 3 mph (5 km/h).2. Place the gearshift lever in
Using the electronic shift 4WD system (if equipped)2H (2WD) - For general on-roaddriving. Sends power to the rearwheels only and should be used forstr
The message center will display 4X4 SHIFT IN PROGRESS during theshift. The message center will then display the system mode selected. Ifany of the abo
You should either know the terrain or examine maps of the area beforedriving. Map out your route before driving in the area. To maintainsteering and b
If your vehicle gets stuckIf your vehicle gets stuck in mud or snow, it may be rocked out byshifting between forward and reverse gears, stopping betwe
TIRES NOT TRAINED – REPEAT (if equipped) — Displayed whenan error occurs while training the TPMS. Refer to TPMS reset procedurein the Tires, Wheels an
WARNING: Vehicles with a higher center of gravity such asutility and four-wheel drive vehicles handle differently thanvehicles with a lower center of
can be found in the Maintenance and Specifications chapter. Youshould become thoroughly familiar with this information before youoperate your vehicle.
Driving through deep water may damage the transmission.Refer to Transmission temperature gauge in the Instrument Clusterchapter for transmission fluid
When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This r
Make sure you allow sufficient distance between you and other vehiclesfor stopping. Drive slower than usual and consider using one of the lowergears.
VEHICLE USED AS A STATIONARY POWER SOURCEAuxiliary equipment called power take-off, or PTO, is often added to theengine or transmission to operate uti
SNOWPLOWINGFord recommends that the Super Duty F-Series used for snow removalinclude the Snow Plow Package Option.Installing the snowplowWeight limits
Operating the vehicle with the snowplow attachedDo not use your vehicle for snow removal until it has been driven atleast 500 miles (800 km).The attac
Transmission operation while plowingOperate the vehicle with the automatic transmission gearshift lever inthe D (Overdrive) position and tow/haul off.
ROADSIDE ASSISTANCEVehicles sold in the U.S. : Getting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany off
ADVTRAC ON MYKEY SETTING (if equipped) — Displayed when aMyKey威 is in use when trying to disable the ESC system and theoptional setting is on. Refer t
U.S. Ford vehicle customers who require Roadside Assistance, call1-800-241-3673.If you need to arrange roadside assistance for yourself, Ford MotorCom
FUEL PUMP SHUT-OFFIn the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fue
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
To remove the fuse panel cover, pullthe panel toward you. When theclips of the panel disengage, let thepanel fall easily.To remove a fuse use the fuse
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Not used (spare)2 15A Upfitter relay #43 30A Not used (spare)4
Fuse/RelayLocationFuse AmpRatingProtected Circuits12 15A Interior lighting, Lighted runningboard lamps13 15A Right turn signals and brakelamps, Right
Fuse/RelayLocationFuse AmpRatingProtected Circuits31 5A Trailer brake controller (brakesignal), Customer access32 15A Moon roof, Telescoping mirrorswi
Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot
Fuse/RelayLocationFuse AmpRatingProtected Circuits10 — Not used11 — Not used12 — Not used13 — Not used14 — Not used15 Diode Fuel pump (diesel engine)1
Fuse/RelayLocationFuse AmpRatingProtected Circuits38 Relay Powertrain control module(PCM) (diesel engine),Electronic control module (ECM)(gas engine)3
TRAILER SWAY REDUCE SPEED (if equipped) — Displayed whenthe trailer sway control has detected trailer sway. For more information,refer to the Driving
Fuse/RelayLocationFuse AmpRatingProtected Circuits62 — Not used63 — Not used64 — Not used65 — Not used66 20A** Fuel pump67 — Not used68 10A** Fuel pum
Fuse/RelayLocationFuse AmpRatingProtected Circuits92 20A* Auxiliary power point #493 20A* Auxiliary power point #394 25A* Upfitter #195 25A* Upfitter
WARNING: The use of tire sealants may damage your tirepressure monitoring system (TPMS) and should not be used.However, if you must use a sealant, the
Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following:• Handling, stability and braki
Spare tire informationNote: If your vehicle is equipped the tire pressure monitoring system(TPMS), the system indicator light will illuminate when the
Tool LocationJack handle, lug wrench, lugwrench extension (only availableon Dual Rear Wheel [DRW]vehicles) and wheel chock (onlyavailable on Single Re
2. Attach the spare tire lock key (A)to the jack handle (B).3. Fully insert the jack handle (withone extension) through the bumperhole and into the gu
Tire change procedureWARNING: When one of the rear wheels is off the ground, thetransmission alone will not prevent the vehicle from moving orslipping
The following steps apply to F–250/F–350 Single Rear Wheel(SRW) vehicles only:5. Insert the hooked end of the jackhandle into the jack and use thehand
• Front passenger side (4x4)Note: View shown from the rear ofthe vehicle to clearly identify thejack point. Place the jack directlyunder the axle.• Re
FOR 4X4 LOW APPLY BRAKE (if equipped) — Displayed whentrying to select 4X4 LOW. For more information, refer to Four-wheeldrive (4WD) operation in the
7. Turn the jack handle clockwiseuntil the wheel is completely off theground and high enough to installthe spare tire.8. Remove the lug nuts with the
• Front driver side (4x4): F–350DRWNote: Make sure the jack fits ontothe flat area on the outboard side ofthe differential housing.• Front passenger s
• Rear: F-450/F-55013. Insert the jack handle into thepump linkage.14. Use an up-and-down motionwith the jack handle to raise thewheel completely off
The following steps apply to all vehicles:18. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lug nuttorque specificat
The following step applies to F–250/F–350 Single Rear Wheel(SRW) vehicles only:22. When installing the wheel centerornaments, ensure that theornament
3. Use your hand or rubber mallet totap the ornament in a star pattern.There should be an even gapbetween the ornament and thewheel.4. Be sure to inst
Stowing the flat/spare tireNote: Failure to follow spare tire stowage instructions may result infailure of cable or loss of spare tire.If you are stow
WHEEL LUG NUT TORQUE SPECIFICATIONSWARNING: When a wheel is installed, always remove anycorrosion, dirt or foreign materials present on the mountingsu
Inspect the wheel pilot hole andmounting surface prior toinstallation. Remove any visiblecorrosion or loose particles.JUMP STARTINGWARNING: The gases
3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake onboth vehicles
ENGINE WARMING PLEASE WAIT XX (diesel engine only) —Displayed in extremely cold weather, typically below –15°F (–26°C), ifthe engine block heater is n
Jump Starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
Note: Towing an ESOF 4x4 vehicle with the front wheels on the groundwithout disengaging the front hubs may cause damage to the automatictransmission.N
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehi
• Ford Genuine Accessories• Service specials and promotions.In Canada:Mailing addressCustomer Relationship CentreFord Motor Company of Canada, Limited
IN CALIFORNIA (U.S. ONLY)California Civil Code Section 1793.2(d) requires that, if a manufactureror its representative is unable to repair a motor veh
procedure outlined earlier in this chapter in the Getting the servicesyou need section, you may be eligible to participate in the BBB AUTOLINE program
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
If your vehicle must be serviced while you are traveling or living inAsia-Pacific Region, Sub-Saharan Africa, U.S. Virgin Islands, CentralAmerica, the
If you buy your vehicle in North America and then relocate to any of theabove locations, register your vehicle identification number (VIN) andnew addr
Note: Diesel Particulate Filter (DPF) regeneration will not initiate at idleor in Power Take Off (PTO) mode. When DRIVE TO CLEAN EXHAUSTFILTER is disp
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i
WAXING• Wash the vehicle first.• Use a quality wax that does not contain abrasives.• Do not allow paint sealant to come in contact with any non-body(l
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
• 6.8L V10 gasoline enginePLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your
helps to remove the hot wax deposited on the wiper blade andwindshield from automated car wash facilities. Be sure to replacewiper blades when they ap
4. Remove the soaked cloth, and if it is not soiled badly, use this cloth toclean the area by using a rubbing motion for 60 seconds.5. Following this,
INTERIORFor fabric, carpets, cloth seats and safety belts:• Remove dust and loose dirt with a vacuum cleaner.• Remove light stains and soil with Motor
LEATHER SEATS FOR THE KING RANCH姞 EDITION ONLY(IF EQUIPPED)Your vehicle is equipped with seating covered in premium, top-grainleather which is extreme
UNDERBODYFlush the complete underside of your vehicle frequently. Keep body anddoor drain holes free from packed dirt.Note: Use care when using a powe
REDUCED ENGINE POWER (diesel engine only) — Displayedapproximately two hours after the DRIVE TO CLEAN EXHAUST SYSTEMmessage has displayed and the vehi
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th
6.2L V8 gasoline engine1. Windshield washer fluid reservoir2. Engine oil dipstick3. Automatic transmission fluid dipstick4. Brake fluid reservoir5. En
6.8L V10 gasoline engine1. Windshield washer fluid reservoir2. Battery3. Automatic transmission fluid dipstick4. Engine oil filler cap5. Engine oil di
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
Poor wiper quality can be improved by cleaning the wiper blades and thewindshield. Refer to Windows and wiper blades in the Cleaning chapter.To prolon
• Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by a service technician.7. Put the dipstick back in
To protect your engine and engine’s warranty, use Motorcraft威 SAE5W-20 or an equivalent SAE 5W-20 oil meeting Ford specificationWSS-M2C945-A. SAE 5W-2
If you see any corrosion on the battery or terminals, remove the cablesfrom the terminals and clean with a wire brush. You can neutralize theacid with
Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe bat
XX MPH MAX UPON RESTART EXHAUST FLUID SYSTEM FAULT(diesel engine only) — Displayed when the SCR system detects afault. The vehicle’s top speed will be
Note: For best results, coolant concentration should be tested with arefractometer such as Rotunda tool ROB75240 available from yourdealer. Ford does
Note: During normal vehicle operation, the engine coolant may changecolor from orange to pink or light red. As long as the engine coolant isclear and
6. Remove the cap from the engine coolant reservoir.7. Fill the coolant reservoir slowly with prediluted engine coolant to theFULL COLD level, or betw
Recycled engine coolantFord Motor Company does not recommend the use of recycled enginecoolant since a Ford-approved recycling process is not yet avai
What you should know about fail-safe cooling (if equipped)If the engine coolant supply is depleted, this feature allows the vehicle tobe driven tempor
3. If this is not possible, wait a short period for the engine to cool.4. Check the coolant level and replenish if low.WARNING: Never remove the coola
• the service engine soon indicator illuminates1. Pull off the road as soon as safely possible and place the vehicle in P(Park).2. Leave the engine ru
WARNING: If you do not use the proper fuel filler cap,excessive vacuum in the fuel tank may damage the fuel systemor cause the fuel cap to disengage i
• Be particularly careful if you are taking “Antabuse” or other forms ofdisulfiram for the treatment of alcoholism. Breathing gasoline and/orethanol v
WARNING: When refueling always shut the engine off andnever allow sparks or open flames near the filler neck. Neversmoke while refueling. Fuel vapor i
• Low Fuel Operation: If the message appears when the vehicle is warmand during low fuel tank level operation, i.e. the tank level is at orvery near e
4. To install the cap, align the tabs on the cap with the notches on thefiller pipe.5. Turn the filler cap clockwise until it clicks.If the check fuel
Octane recommendations“Regular” unleaded gasoline with a pump (R+M)/2 octane rating of 87 isrecommended. Some stations offer fuels posted as “Regular”
Do not add aftermarket fuel additive products to your fuel tank. Itshould not be necessary to add any aftermarket products to your fueltank if you con
ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform
2. Each time you fill the tank, record the amount of fuel added (ingallons or liters).3. After at least three to five tank fill-ups, fill the fuel tan
• Warming up a vehicle on cold mornings is not required and mayreduce fuel economy.• Resting your foot on the brake pedal while driving may reduce fue
EMISSION CONTROL SYSTEMWARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine
Do not make any unauthorized changes to your vehicle or engine. Bylaw, vehicle owners and anyone who manufactures, repairs, services,sells, leases, tr
Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect
POWER STEERING FLUIDCheck the power steering fluid. Refer to scheduled maintenanceinformation. If adding fluid is necessary, use only MERCON威 ATF.• Ga
Scheduled Maintenance 424Normal scheduled maintenance and log 428Index 442The information contained in this publication was correct at the time of goi
Press the OK button to selecthighlighted options and confirmchoices/messages.Main menuFrom the main menu screen you can choose the following:• Gauge M
BRAKE FLUID• Vacuum boost system• Hydroboost systemThe fluid level will drop slowly as the brakes wear, and will rise when thebrake components are rep
1. Drive the vehicle 20 miles (30 km) or until it reaches normal operatingtemperature.2. Park the vehicle on a level surface and engage the parking br
Correct fluid levelFor vehicles equipped with 5-speed transmissions, the fluid should bechecked at normal operating temperature 150°F-170°F (66°C-77°C
Adjusting automatic transmission fluid levelsBefore adding any fluid, make sure the correct type is used. The type offluid used is normally indicated
TRANSFER CASE FLUID (IF EQUIPPED)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough fluid throughthe fil
The following procedure is for vehicles equipped with a gasoline engine.If your vehicle is equipped with a diesel engine, refer to the dieselsupplemen
5. Release the three clamps thatsecure the cover to the air filterhousing. Push the air filter covertoward the center of the vehicle andup slightly to
10. Reconnect the mass air flowsensor electrical connector to theoutlet tube. Make sure the lockingtab on the connector is in the“locked” position (co
• Lubricate all hood, door and trunk lid hinges, and latches with a lightgrade oil. See the Cleaning chapter for more information.• Cover interior tri
Brakes• Make sure brakes and parking brake are fully released.Tires• Maintain recommended air pressure.Miscellaneous• Make sure all linkages, cables,
Trip A/BIn this mode, Trip A or B registers the following:• Trip Time — shows the elapsed trip time. This timer will stop whenthe vehicle is turned of
MOTORCRAFT PART NUMBERSComponent 6.2L V8 engine 6.8L V10 engineAir filter element FA-1883 FA-1883Oil filter FL-820-S FL-820-SBattery (standard) BXT-65
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationFront axle 5.8 pints (2.8L)Motorcraft
Item Capacity Ford part nameFord part number /Ford specificationEngine and fuel coolant- diesel engineRefer to the diesel supplement.Engine oil (inclu
Item Capacity Ford part nameFord part number /Ford specificationHinges, latches, strikerplates, fuel filler doorhinge and seat tracks— Multi-Purpose G
Item Capacity Ford part nameFord part number /Ford specificationWindshield washer fluid Fill as requiredMotorcraft威 PremiumWindshield WasherConcentrat
ENGINE DATAEngine 6.2L V8 engine 6.8L V10 engineCubic inches 378 413Required fuelMinimum 87 octane orEthanol (E85)Minimum 87 octaneFiring order 1-5–4–
6.8L V10 engine - without A/CIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulation
Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX
TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis
FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C
It is important to press RESET in order to reset the function aftersetting the speed control to get accurate highway fuel economy readings.For more in
Peace of mind•Keyless entry keypad •Back up alarm*•Remote start •Cable lock*•Vehicle security systems •Bed hooks*•Wheel locks •Tool/Cargo boxes*•Prote
FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 32 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the
Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With
FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is
GENERAL MAINTENANCE INFORMATIONThe following information pertains to 6.2L V8 and 6.8L V10 gasolineengines only. Scheduled maintenance for the diesel e
owner’s responsibility to determine the equivalency of such parts. Pleaseconsult your Warranty Guide for complete warranty information.Chemicals or ad
Value Shopping for Your Vehicle’s Maintenance NeedsYour dealership recognizes the competitive landscape of maintenance andlight repair automotive serv
Check every six monthsParking brake for proper operationSafety belts and seat latches for wear and functionSafety warning lamps (brake, ABS, airbag, s
NORMAL SCHEDULED MAINTENANCE AND LOGThe following section contains the “Normal Schedule”. This schedule ispresented at specific mileage (kilometer) in
6.2L and 6.8L enginesMiles (x 1,000)* 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75Kilometers (x 1,000)* 12 24 36 48 60 72 84 96 108 120Months* 6 12 18 24 30
• 4X4 System• Traction Control• Advancetrac + RSCTrailer: Press the right arrow key (when in the Off Road menu) toreach the Trailer menu (vehicle must
6.2L and 6.8L enginesMiles (x 1,000)* 82.5 90 97.5 105 112.5 120 127.5 135 142.5 150Kilometers (x 1,000)* 132 144 156 168 180 192 204 216 228 240Month
6.2L and 6.8L enginesEvery 15,000 miles(24,000 km)Replace cabin air filter (if equipped)Every 30,000 miles(48,000 km)Replace climate-controlled seat f
Maintenance Schedule LogDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDAT
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
SPECIAL OPERATING CONDITIONSThe following information pertains to 6.2L V8 and 6.8L V10 gasolineengines only. Scheduled maintenance for the diesel engi
Extensive idling and/or low-speed driving for long distances as inheavy commercial use (i.e. delivery, taxi, patrol car or livery)Inspect frequently,s
Operating in dusty conditions such as unpaved or dusty roadsEvery 30,000 miles(48,000 km)Change automatic transmission fluid (except 6R80and TorqShift
Special Operating Condition LogDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
Trailer*Delete Trailer Press the right arrow button when this is highlightedto show currently stored trailers. Use the up/downarrows to highlight the
EXCEPTIONSThere are several exceptions to the Normal Schedule. They are listedbelow:Normal vehicle axle maintenance: Rear axles and power take-off(PTO
Edge/MKX AWD only – vehicles operating off-road in sand during highambient temperatures must replace the AWD PTU (All-wheel drivePower Transfer Unit)
AAccessory delay ...104AdvanceTrac ...275Airbag supplemental restraintsystem ...1
LATCH ...206recommendations ...197Child safety seats -booster seats ...212
Engine oil ...375checking and adding ...375dipstick ...375filter, specifica
Infant seats(see Safety seats) ...199Inspection/maintenance (I/M)testing ...398Instrument panel
PParental MyKeyprogramming ...129Parking brake ...273Parts(see Motorcraft威 parts) ...410Ped
SecuriLock passive anti-theftsystem ...149–150Servicing your vehicle ...370Setting the clock ...
WWarning lights (see Lights) ...14Washer fluid ...374Water, Driving through ...315Windowspower ...
* If equipped—your vehicle may be equipped with some or all of theseoptions.Vehicle*Autolamp Delay Off or XXX secondsCompass Zone Setting (1–15) See t
Vehicle* (cont’d)Menu ControlStandard: with standard set, pressing the up/downarrows from a lower level menu will escape to themain menu.Memory On: wi
InformationIn this mode, you can view different vehicle system information andperform a system check.When “Press OK for info” is displayed, pressing O
Compass/transmission indicator displaysThe compass heading will display in the upper right corner of the messagecenter; the transmission gear indicato
BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is lowand the brake system should be inspected immediately. Refer to Brakefluid in the Mainten
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
DRIVE TO CLEAN EXHAUST SYSTEM (diesel engine only) —Displayed when the Diesel Particulate Filter (DPF) is full of particles(exhaust soot) and the vehi
ENGINE TURNS OFF IN XX SECONDS (diesel engine only) —Displayed when the vehicle is in the final 30 seconds of a countdown towhere the engine will inte
SPEED LIMITED TO XX MPH UPON RESTART EXHAUST FLUIDEMPTY (diesel engine only) — Displayed when the remaining dieselexhaust fluid level is depleted. Spe
ENGINE IDLED - SEE OWNER’S MANUAL EXHAUST FLUIDSYSTEM FAULT (diesel engine only) — Displayed when the SCRsystem detects a fault. The engine will event
WATER IN FUEL DRAIN FILTER SEE MANUAL (if equipped) —Displayed when the water separator has reached a predeterminedcapacity and needs to be drained. R
TRAIN SPARE TIRE (if equipped) — Displayed when training theTPMS. Refer to TPMS reset procedure in the Tires, Wheels andLoading chapter for more infor
TO EXIT 4X4 LOW SHIFT TO N (if equipped) — Displayed when2WD is selected while the vehicle has been stopped in 4X4 LOW. Formore information, refer to
HILL DESCENT CONTROL READY (if equipped) — Displayedwhen the hill descent control switch is turned on.REDUCE ACCELERATOR TO PREVENT WHEEL SLIP (ifequi
SPEED LIMITED TO 130 KM/H — Displayed when starting thevehicle and MyKey威 is in use and the MyKey speed limit is on. Refer toMyKey威 in the Locks and S
TRAILER CONNECTED (if equipped) — Displayed when a correcttrailer connection (a trailer with electric trailer brakes) is sensed duringa given ignition
Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti
AUDIO SYSTEMSAM/FM stereo system (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strong
1. / (Tuner): Press tomanually go up or down the radiofrequency. Press and hold for a fastadvance through radio frequencies.Also use in AUDIO mode to
6. ON/OFF/Volume: Press VOL -PUSH to turn ON/OFF. Turn VOL -PUSH to increase/decrease volume.7. CLK (Clock): Press CLK totoggle between the clock and
Accessory delay: Your vehicle is equipped with accessory delay whichallows you to operate the window switches and the audio for up to10 minutes after
• SAVE SONG: Press OK to save the currently playing song title in thesystem’s memory. (If you try to save something other than a song,CANT SAVE will a
When the six strongest stations are filled, the station stored in preset 1will begin playing. If there are less than six strong stations, the systemwi
COMPRESS (Compression): Available only in CD/MP3 mode. PressMENU until COMPRESS ON/OFF appears in the display.Use/ / SEEK, SEEK to toggle ON/OFF. When
7. SHUFFLE: In CD/MP3 mode,press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engage shuffle mode right away, p
In satellite radio mode (if equipped), press and release to enterTEXT MODE and display the current song title. While in TEXT MODE,press again to scrol
Auxiliary input jack (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommend
Do not add friction modifier compounds or special break-in oils since theseadditives may prevent piston ring seating. See Engine oil in theMaintenance
5. Turn the portable music player on and adjust the volume to 1/2 thevolume.6. Press AUX on the vehicle radio repeatedly until LINE, LINE IN orSYNC LI
USB port (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdriver
CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C
CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m
Radio Display Condition Action RequiredNO TEXT Category informationnot available.Category informationnot available at thistime on this channel.The sys
SINGLE ZONE CLIMATE CONTROL1.Defrost: Distributes outside air through the windshield defrostervents and de-mister vents. Can be used to clear the wind
5. Recirculated air (if equipped): Press to activate/deactivate airrecirculation in the vehicle. Recirculated air may reduce the amount oftime needed
Using your vehicle as an ambulanceIf your light truck is equipped with the Ford Ambulance PreparationPackage, it may be utilized as an ambulance. Ford
If you are driving during extreme high ambient temperatures and idlingfor extended periods of time in gear, it is recommended to run the A/Cin the MAX
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Optional or Standard mes
4. Manual control: Allows you to manually select where airflow isdirected. To return to full automatic control, press AUTO. Whenchoosing to control ai
10. Passenger temperature: Turn to increase/decrease the airtemperature on the passenger side of the vehicle. The recommendedinitial setting is betwee
• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield.• To improve the A/C cool down, drive with the windows slightly
REAR WINDOW DEFROSTER (IF EQUIPPED)RThe rear defroster control is located on the climate control panel andworks to defrost your rear window from fog a
For moderate weather conditions:• The interior cabin will be heated, cooled or off, based upon theprevious operating state (last ignition-on cycle).•
HEADLAMP CONTROLRotate the headlamp controlclockwise to the first positiontoturn on the parking lamps.Rotate clockwise to the secondpositionto also tu
3. Turn the ignition switch to on and then back to off.4. Turn the headlamp control to the autolamp position. The headlampswill turn on.5. Wait the de
Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the on position,• the head
Event Data RecordingThis vehicle is equipped with an event data recorder (EDR). Themain purpose of an EDR is to record, in certain crash or nearcrash-
AIMING THE HEADLAMPSYour vehicle is equipped with an aerodynamic headlamp system. Theaerodynamic headlamps can only be aimed in the vertical direction
5. Locate the vertical adjuster oneach headlamp, then use a #2Phillips head to turn the adjustereither counterclockwise (to adjustdown) or clockwise (
INTERIOR LAMPSFront map lamps (if equipped)The map lamps are located on the overhead console. Press the controlson either side of each map lamp to tur
Examples of unacceptable moisture (usually caused by a lamp waterleak) are:• Water puddle inside the lamp• Large water droplets, drip marks or streaks
Replacing headlamps, park lamps, turn lamps1. Make sure that the exterior lamps are off, then open the hood.2. Using masking tape or a marker,make an
10. For the headlamp bulb, removethe bulb by turning itcounterclockwise and pulling itstraight out.11. For the park or turn lamp bulb,remove the bulb
3. Rotate the bulb socket counterclockwise and remove from lampassembly.4. Pull the bulb straight out of the socket.Install the new bulb(s) in reverse
Replacing front clearance and identification lamp bulbs(if equipped)1. Make sure the headlamps are off.2. Remove the screw and lens fromthe lamp assem
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT/TELESCOPE STEERING WHEELTo adjust the steering wheel:1. Pull the lever down to unlock thesteering column.2. While the lever is in the downpositio
Commentaires sur ces manuels