Ford 2011 Fiesta v.3 Manuel d'utilisateur

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Trip computer 17Message center 18Multifunction display 19Entertainment Systems

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

UPGRADES AND RECOVERY MEDIA: If the SOFTWARE is providedby FORD MOTOR COMPANY separate from the DEVICE on media suchas a ROM chip, CD ROM disk(s) or v

PRODUCT SUPPORT: Product support for the SOFTWARE is notprovided by MS, its parent corporation Microsoft Corporation, or theiraffiliates or subsidiari

WARNING: Operating certain parts of this system while drivingcan distract your attention away from the road, and possiblycause an accident or other se

MANUAL HEATING AND AIR CONDITIONING SYSTEMManual system with A/C shown; heater only system similar.1.: Turn to select the desired fan speed.2. Air flo

: Distributes outside air through the windshield defroster anddemister vents. Can be used to clear thin ice or fog from thewindshield. The system will

and put the vehicle’s transmission into the P (Park) gear position(automatic transmission only) to continue to receive cool air from yourA/C system.Fo

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the low beam headlampso

Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the on position and• the h

• (1) 8 feet (2.4 meters)• (2) Center height of lamp toground• (3) 25 feet (7.6 meters)• (4) Horizontal reference line2. Measure the height from thece

TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.When changing lanes, the turn signal indicat

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

Dome lamps and map lamps, rear lampsPress the buttons to turn the maplamps on/off.Ambient lighting (if equipped)Illuminates footwells, cupholdersand t

BULB REPLACEMENTLamp assembly condensationExterior lamps are vented to accommodate normal changes in pressure.Condensation can be a natural by-product

Function Number of bulbs Trade number4-door rear deck lamp(backup)1 9215-door rear lamp(stop/reverse)2 3157K5-door rear lamp(turn)1 3157A(amber)Licens

1. Make sure the headlamp controlis in the off position, then open thehood.2. Remove the screws and pushpinholding the lamp assembly (1).(Driver side

1. Remove the bulb cover.2. Turn the bulb holdercounterclockwise and remove it.3. Disconnect the electrical connector.4. Reverse the procedure to inst

2. Turn the bulb holdercounterclockwise and remove it.3. Disconnect the electrical connector.4. Reverse the procedure to install the new bulb.Replacin

Replacing the side marker lamps1. Turn the bulb holder clockwiseand remove it.2. Remove the bulb from the bulbholder.3. Reverse the procedure to insta

Replacing the rear stop lamp (5-door)1. Turn the bulb holdercounterclockwise and remove it.2. Remove the bulb from the holder.3. Reverse the procedure

2. Remove the bulb from the holder.3. Reverse the procedure to install the new bulb.Replacing the turn signal rear lamp (5-door)1. Turn the bulb holde

Replacing bodyside rear lamp bulb (4-door)1. Open the deck lid and remove the interior bodyside carpet.2. Turn the bulb holdercounterclockwise and rem

WARNING LIGHTS AND CHIMESWarning lights can alert you to a vehicle condition that may becomeserious enough to cause expensive repairs. A warning light

3. Remove the bulb (3) from theholder.4. Reverse the procedure to install the new bulb.5. Reinstall the carpet.Replacing the license plate lamps1. Car

WINDSHIELD WIPERSMove the lever down for a singlewipe.For intermittent operation,move control up one position andadjust the rotary control to thedesir

TILT/TELESCOPE STEERING WHEELTo adjust the steering wheel:1. Pull the lever down to unlock thesteering column.2. While the lever is in the downpositio

Note: Do not plug optional electrical accessories into the cigarettelighter socket (if equipped). Improper use of the lighter can causedamage not cove

Press and pull the window switchesto open and close windows.• Press down (to the first detent)and hold the switch to open.• Pull up (to the first dete

3. If the window does not close after the third attempt, contact yourauthorized dealer as soon as possible.Resetting the bounce-back featureWARNING: T

Automatic dimming interior rear view mirror (if equipped)The interior rear view mirror has an auto-dimming function. Theelectronic day/night mirror wi

Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re

Using speed controlsThe speed controls are located on the steering wheel. The followingbuttons work with speed control:SET+: Press to set a speed or t

Increasing speed while using speed controlTo increase the set speed:• Press and hold SET+ until you get to the desired speed, then release.You can als

WARNING: Under engine misfire conditions, excessive exhausttemperatures could damage the catalytic converter, the fuelsystem, interior floor coverings

M (Mode): Press repeatedly to scroll through available audio modes.For further information on the SYNC威 system, refer to the SYNC威supplement.MOON ROOF

POSITIVE RETENTION FLOOR MATWARNING: Do not install additional floor mats on top of thefactory installed floor mats as they may interfere with theacce

KEYSIntegrated keyhead transmitters (IKTs) (If equipped)Your vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade star

The IA key also contains aremovable mechanical key bladethat can be used to unlock thedriver door. To release themechanical key blade, press thereleas

If both front doors are closed, the vehicle can be locked by any method,regardless of whether the key is in the ignition or not.Smart locks for intell

• the ignition is on,• you shift into any gear putting the vehicle in motion, and• the vehicle attains a speed greater than 12 mph (20 km/h).If a door

• To program the autounlock feature, press the power door lock controlfor less than 1 second and release. Each short press of the powerdoor lock contr

To open the luggage compartmentdoor (lid) from within the luggagecompartment, pull the illuminated“T” shaped handle and push up onthe trunk lid. The h

The integrated keyhead transmitters (IKTs) and intelligent access keys(IA key) comply with part 15 of the FCC rules and with RSS-210 ofIndustry Canada

• arm and disarm the perimeter anti-theft system.• operate the illuminated entry feature.The remote entry lock/unlock feature operates in any ignition

Anti-lock brake system: If theABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected, have the systemserviced immediately by

may be necessary to mechanically unlock your door. The mechanical keyblade in your IA key can be used to open the driver’s door in thissituation (refe

To replace the battery:Integrated Keyhead Transmitter(IKT)1. Carefully insert a flat object (e.g.a screwdriver) into the recess onthe back of the key

3. Twist a flat object in the positionshown to separate the two halves ofthe transmitter.4. Carefully insert a flat object inthe position show to open

Please read and understand the entire procedure before you begin.To reprogram the remote entry transmitters:1. Insert the first programmed key into th

Illuminated entryThe interior lamps illuminate for 25 seconds when:• the vehicle is unlocked by any method other than the interior powerdoor lock cont

objects from touching the coded key while starting the engine. Theseobjects will not cause damage to the coded key, but may cause amomentary issue if

Replacing coded keys can be very costly. Store an extra programmed keyaway from the vehicle in a safe place to help prevent anyinconveniences. Please

FRONT SEATSWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the eve

3. Lower the head restraint by pressing and holding the guide sleeveadjust release button (3) and pushing down on the head restraint (1).Properly adju

WARNING: To reduce the risk of possible serious injury: Do nothang objects off seat back or stow objects in map pocket (ifequipped) when a child is in

Engine coolant temperature:Illuminates when the engine coolanttemperature is high. Stop thevehicle as soon as possible, switch off the engine and let

• Recline adjustmentLift the control to adjust the angleof the seatback.WARNING: Reclining the seatback can cause an occupant toslide under the seat’s

To operate the heated seats:• Press the button located on theinstrument panel to activate.• Press again to deactivate.The heated seats will activate w

To lower the seatback(s) from inside the vehicle, do the following:1. Press the unlock buttons (1)down and hold them there.2. Push the seatback forwar

WARNING: Before returning the seatback to its originalposition, make sure that cargo or any objects are not trappedbehind the seatback. Make sure that

The fact that the pretensioners or airbags did not activate for both frontseat occupants in a collision does not mean that something is wrong withthe

WARNING: Air bags can kill or injure a child in a child seat.NEVER place a rear-facing child seat in front of an active airbag. If you must use a forw

Front outboard safety belt energy management retractorsThe front safety belt energy management retractors allow webbing to bepulled out of the retract

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

Combination lap and shoulder beltsThe front outboard and rear safety restraints in the vehicle arecombination lap and shoulder belts.1. Insert the bel

Pregnant women should alwayswear their safety belt. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips

AdvanceTrac威/Traction control(if equipped): Displays when theAdvanceTrac威/Traction control isactive. If the light remains on, havethe system serviced

How to use the automatic locking mode1. Buckle the combination lap andshoulder belt.2. Grasp the shoulder portion andpull downward until the entire be

Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label.

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war

If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the onposition or less than1-2 minutes h

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra

Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate

WARNING: While the design allows you to deactivate yourBelt-Minder威, this system is designed to improve your chances ofbeing safely belted and survivi

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The supplemental restraint system is designed to work with the safetybelt to help protect the driver and rig

WARNING: When possible, all children 12 years old and undershould be properly restrained in a rear seating position.WARNING: The National Highway Traf

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

GAUGESShown in standard measure. Metric similar.1. Tachometer: Indicates the engine speed in revolutions per minute.Driving with your tachometer point

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

• a readiness light and tone• and the electrical wiring which connects the components• Side curtain airbag system. Refer to Side curtain airbag system

• the system determines that a small child is present in a forward-facingchild restraint that is installed according to the manufacturer’sinstructions

If a person of adult size is sitting in the front passenger’s seat, but the⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator lamp is lit, it ispos

The front passenger sensing system may detect small or medium objectsplaced on the seat cushion. For most objects that are in the frontpassenger seat,

WARNING: To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a chi

WARNING: Any alteration/modification to the front passengerseat may affect the performance of the front passenger sensingsystem.Determining if the sys

WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. Contact your authorize

The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of

WARNING: Do not lean your head on the door. The side airbagcould injure you as it deploys from the seat.WARNING: Do not attempt to service, repair, or

mi (km) TRIP — Trip odometer: Registers the mileage of individualjourneys.mi (km) TO E — Distance to empty (if equipped): Indicates theapproximate dis

How does the side air curtain system work?The design and development of theside air curtain system includedrecommended testing proceduresthat were dev

provided to occupants in side impact collisions. The seat-mounted sideairbag was designed to inflate between the door panel and occupant tofurther enh

• The readiness light will not illuminate immediately after ignition isturned on.• A series of five beeps will be heard. The tone pattern will repeatp

WARNING: All children are shaped differently. TheRecommendations for Safety Restraints are based on probablechild height, age and weight thresholds fr

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeLargerchildrenChildren who have outgrown

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle.If the child is the proper height, age, and weigh

Installing child safety seats with combination lap and shoulderbeltsCheck to make sure the child seat is properly secured before each use.Children 12

1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan

• Chimes: Move right to enter the menu, then up or down to selectfrom warning chimes or info chimes. Press OK to confirm.Clock: Select Clock then move

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear

9. Attach the tether strap (if the child seat is equipped). Refer toAttaching child safety seats with tether straps later in this chapter.10. Before p

Your vehicle has LATCH loweranchors for child seat installation atthe seating positions marked withthe child seat symbol.The LATCH anchors are located

Use of inboard lower anchors from the outboard seating positions(center seating use)The lower anchors at the center of the second row rear seat are sp

The rear seats of your vehicle are equipped with built-in tether strapanchors located behind the seats as described below.Four door: The tether anchor

2. Locate the correct anchor for theselected seating position.3. Open the tether anchor cover.4. Clip the tether strap to theanchor as shown.If the te

2. Locate the correct anchor for theselected seating position.3. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly

Although the lap/shoulder belt will provide some protection, childrenwho have outgrown a typical child seat are still too small for lap/shoulderbelts

Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

Locks and Security 132Keys 132Locks 133Anti-theft system 144Seating and Safety Restraints 147Seating 147Safety restraints 153Airbags 167Child restrain

Message Warning Lamp atInstrument ClusterSystemINTERIOR SCANDEACTIVATED—Anti-theft securitysystemIMMOBILIZERMALFUNCTIONSERVICE NOW—Anti-theft security

Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli

WARNING: The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydro

Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr

WARNING: Under-inflation is the most common cause of tirefailures and may result in severe tire cracking, tread separationor “blowout”, with unexpecte

Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w

• Do not run over curbs or hit the tire against a curb when parkingWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the

Message Warning Lamp atInstrument ClusterSystemKEY BATTERY LOWREPLACE BATTERY—Passive entry/passivestart systemTO START PRESSBRAKE—Passive Entry/Passi

• Front-wheel drive (FWD) vehicles(front tires at top of diagram)Sometimes irregular tire wear can be corrected by rotating the tires.Note: If your ti

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Understanding your tire pressure monitoring system (TPMS)The tire pressure monitoring system measures pressure in your four roadtires and sends the ti

When you believe your system is not operating properlyThe main function of the tire pressure monitoring system is to warn youwhen your tires need air.

Message Warning Lamp atInstrument ClusterSystemVEHICLE NOT INPARK SELECT P— Starting/TransmissionVEHICLE NOT INPARK SELECT P— Starting/TransmissionDOO

When inflating your tiresWhen putting air into your tires (such as at a gas station or in yourgarage), the tire pressure monitoring system may not res

If you choose to install snow tires on your vehicle, they must be thesame size, construction, and load range as the original tires listed on thetire p

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment.GAW (Gross Axle Weight) – is the

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

WARNING: Do not use replacement tires with lower loadcarrying capacities than the original tires because they maylower the vehicle’s GVWR and GAWR lim

• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the l

Before you tow your vehicle, follow these directions for your specificvehicle configuration after it is hooked-up to the RV or tow dolly:Vehicles with

Vehicles with an automatic transmission and push button startsystem:1. Release the parking brake.2. Activate the ignition by pressing the START/STOP b

AUDIO SYSTEMSAM/FM stereo or AM/FM stereo single CD/MP3 (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident

STARTINGPositions of the ignitionIf your vehicle is equipped with a push button start system, refer toPush button start system in this section for ign

WARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine compartment and exhaus

• Make sure the gearshift is in P(Park).If starting a vehicle with a manualtransmission:• Make sure the parking brake isset.• Press the clutch pedal t

1. Turn the key to II (on) withoutturning the key to III (start).2. Turn the key to III (start), thenrelease the key as soon as theengine begins crank

2. On — press the START/STOP button without applying the brake pedal(automatic transmission) or clutch pedal (manual transmission). This willpower you

Fast restart feature: The fast restart feature allows you to re-startyour vehicle within 10 seconds of switching the vehicle off, if a valid IAkey is

Important ventilating informationIf the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least 1 inch (2.5

• To reduce the risk of electrical shock, do not use your heater withungrounded electrical systems or two pronged (cheater) adapters.Also ensure that

Refer to Warning lights andchimes in the Instrument Clusterchapter for information on the brakesystem warning light.Under normal operating conditions,

Parking brakeTo set the parking brake (1), pullthe parking brake handle up as faras possible.The BRAKE warning lamp willilluminate and will remainillu

Display icons: Your system’s display will illuminate icons for the modewhich is currently active, such as:RadioCDAuxiliary inputSettings: This icon wi

• Electronic stability control (ESC), which functions to help avoid skidsor lateral slidesWARNING: Vehicle modifications involving braking system,afte

cause the AdvanceTrac威 system to operate. If the stability control lightilluminates steadily, have the system serviced by an authorized dealerimmediat

Electronic stability control (ESC)Electronic stability control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa

In R (Reverse), ABS and the engine and brake traction control featureswill continue to function; however, ESC is disabled.AdvanceTrac威 FeaturesTCS swi

WARNING: The EPS has diagnostics checks that continuouslymonitor the EPS to ensure proper operation of the electronicsystem. When an electronic error

If the fuse is not blown and the brake lamps are working properly, thefollowing procedure will allow you to move the gearshift lever from P(Park):1. A

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED)Understanding the gearshift positions of the 6–speed automatictransmission (if equipped)P (Park)This pos

D (Drive)The normal driving position for the best fuel economy. Transmissionoperates in gears one through six.D (Drive) with Overdrive Cancel/Grade As

To return to D (Drive), press the transmission control switch again.• The grade assist lamp in the instrument cluster will not be illuminated.• The tr

Activating HSA1. Press the brake pedal to bring the vehicle to a complete standstill.Keep the brake pedal pressed.2. If the sensors detect that the ve

• Sirius (if equipped): Scroll to select Sirius and then press OK toenter the menu. Scroll to select from SAT1. SAT2 or SAT3 modes.Note: Sirius must b

MANUAL TRANSMISSION OPERATION (IF EQUIPPED)Using the clutchManual transmission vehicles have a starter interlock that preventscranking the engine unle

Recommended shift speedsDo not downshift into 1 (First) when your vehicle is movingfaster than 15 mph (24 km/h). This will damage the clutch.Upshift a

BLIND SPOT MIRRORSBlind spot mirrors have an integrated convex spotter mirror built intothe upper outboard corner of the outside mirrors. They are des

DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

Canadian customers refer to your Warranty Guide or visit ourwebsite at www.ford.ca for information on:Using roadside assistanceComplete the roadside a

Should your vehicle shut off after a collision due to this feature, you mayrestart your vehicle by doing the following:1. Turn the ignition switch to

COLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge20A Yellow Yellow Yellow Blue Blue25A Natural Natural — Natural Natu

The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected circuitsF1 15A Ignition switch, Keyless entryignition relay, Keyless entryacc

Fuse/RelayLocationFuse AmpRatingProtected circuitsF21 10A BCM, Climate control, Passiveanti-theft system transceiver,Electronic power steering module,

• Occupancy mode: Scroll to select Occupancy mode and moveright or press OK to enter. Then, scroll to select from Optimize Allor Optimize Driver. Occu

Fuse/RelayLocationFuse AmpRatingProtected circuitsR5 — Passenger heated seat relayR6 — IA module – accessory relayR7 — IA module – ignition relayR8 —

To remove a fuse, use the fuse puller tool provided on the inside of thepassenger compartment fuse panel cover.The high-current fuses are coded as fol

Fuse/RelayLocationFuse AmpRatingProtected circuitsF8 30A* Fuel pumpF9 20A* ABS module valveF10 — Not usedF11 30A* Starter inhibit relay, Starter motor

Fuse/RelayLocationFuse AmpRatingProtected circuitsF31 20A** Low beam relayF32 20A** BCM – battery saver, hornF33 30A** BCM – rear window defrosterF34

Have a flat serviced by an authorized dealer in order to prevent damageto the TPMS sensors, refer to Tire pressure monitoring system(TPMS) in the Tire

• Tow a trailer• Use snow chains on the end of the vehicle with the dissimilar sparetire• Use more than one dissimilar spare tire at a time• Use comme

• Driving vehicles equipped with a camper body• Driving vehicles with a load on the cargo rackDrive cautiously when using a full-size dissimilar spare

Note: Passengers should not remain in the vehicle when the vehicle isbeing jacked.1. Remove the spare tire and jack byturning their tie-down boltscoun

5. Position the jack in the indentionson the sill next to the tire you arechanging. Turn the jack handleclockwise until the tire is off theground.6. R

WARNING: When a wheel is installed, always remove anycorrosion, dirt or foreign materials present on the mountingsurfaces of the wheel or the surface

14. (Eject): Press to eject a CD (if equipped.)15. Cursor controls: Use to cycle through various menu selections.Note: You can either press the arrows

JUMP STARTINGWARNING: The gases around the battery can explode ifexposed to flames, sparks, or lit cigarettes. An explosion couldresult in injury or v

1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery.2. Connect the other end of thepositive (+) cable to the

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.Note: In the illustration, the vehicle on the bottom i

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

If the vehicle is towed by other means or incorrectly, vehicledamage may occur.Ford Motor Company produces a towing manual for all authorized towtruck

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehi

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

You are required to submit your warranty dispute to BBB AUTO LINEbefore asserting in court any rights or remedies conferred by CaliforniaCivil Code Se

You can get more information by calling BBB AUTO LINE at1-800-955-5100, or writing to:BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia

Setting the clock: Press the H or M buttons on the outside of themultifunction to access the clock settings. Once you are in the clocksetting, press t

GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.

If your vehicle must be serviced while you are traveling or living in theMiddle East, contact the nearest authorized dealer. If the authorizeddealer c

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

• Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, sid

• Do not spray a hot engine with cold water to avoid cracking theengine block or other engine components.• Spray Motorcraft威 Engine Shampoo and Degrea

WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub

• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to a

• If a ring forms on the fabric after spot cleaning, clean the entire areaimmediately (but do not oversaturate) or the ring will set.• Do not use hous

Regular cleaning and conditioning will maintain the appearance of theleather.CleaningFor dirt, use a vacuum cleaner then use a clean, damp cloth or so

• SYNC phone (if equipped): Scroll to select Phone Menu and thenpress OK to enter the menu. Refer to the SYNC威 section in thischapter for more informa

FORD AND LINCOLN CAR CARE PRODUCTSYour Ford or Lincoln authorized dealer has many quality productsavailable to clean your vehicle and protect its fini

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

WARNING: To reduce the risk of vehicle damage and/orpersonal burn injuries, do not start your engine with the aircleaner removed and do not remove it

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT1. Engine coolant reservoir2. Engine oil filler cap3. Battery4. Brake/Clutch fluid reservoir5. Power d

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

To replace the wiper blades:1. Pull the wiper arm away from thewindshield.2. Press the locking button (1).3. Remove the wiper blade (2).Note: Make sur

2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler cap

Change your engine oil and filter according to the appropriate schedulelisted in the scheduled maintenance information.Ford production and Motorcraft威

WARNING: When lifting a plastic-cased battery, excessivepressure on the end walls could cause acid to flow through thevent caps, resulting in personal

When the battery is disconnected or a new battery installed, theautomatic transmission must relearn its adaptive strategy. As a result ofthis, the tra

Customer Assistance 275Reporting safety defects (U.S. only) 282Reporting safety defects (Canada only) 282Cleaning 283Maintenance and Specifications 29

9. PHONE: Press to access SYNC威 phone features if available. Refer tothe SYNC威 section for more information. If your vehicle is not equippedwith SYNC威

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the FULL COLD level, or within theCOLD

• DO NOT MIX different colors or types of coolant in your vehicle.Make sure the correct coolant is used. DO NOT MIX recycled coolantand new (unused) c

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap.5. Fill the coolant reservoi

Severe climatesIf you drive in extremely cold climates:• It may be necessary to increase the coolant concentrationabove 50%.• NEVER increase the coola

If both lamps illuminate together, stop your vehicle as soon as it is safeto do so (continued use may cause reduced power and cause the engineto stop)

• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kindcan lead to eye and respiratory tract irritation. In severe cases,excessive or p

RefuelingWARNING: Fuel vapor burns violently and a fuel fire can causesevere injuries. To help avoid injuries to you and others:• Read and follow all

4. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about five seconds after pumping fuel before removing thefuel filler noz

Octane recommendationsYour vehicle is designed to use“Regular” unleaded gasoline with apump (R+M)/2 octane rating of 87.Some stations offer fuels post

If you have run out of fuel:• You may need to cycle the ignition from off to on several times afterrefueling to allow the fuel system to pump the fuel

16. Sound menu: Press access Treble, Bass, Fade (if equipped) andBalance menu options. Use/ to cycle through the various options.When the desired opti

4. When done, clean the funnel or properly dispose of it. Extra funnelscan be purchased from your authorized dealer if you choose to disposeof the fun

• Have the vehicle loading and distribution the same every time.Your results will be most accurate if your filling method is consistent.Calculating fu

• Revving the engine before turning it off may reduce fuel economy.• Using the air conditioner or defroster may reduce fuel economy.• You may want to

EMISSION CONTROL SYSTEMYour vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to co

Do not make any unauthorized changes to your vehicle or engine. Bylaw, vehicle owners and anyone who manufactures, repairs, services,sells, leases, tr

Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect

The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX lines are

AIR FILTERRefer to scheduled maintenance information for the appropriateintervals for changing the air filter element.When changing the air filter ele

General• Store all vehicles in a dry, ventilated place.• Protect from sunlight, if possible.• If vehicles are stored outside, they require regular mai

Cooling system• Protect against freezing temperatures.• When removing vehicle from storage, check coolant fluid level.Confirm there are no cooling sys

The auxiliary input jack (AIJ)provides a way to connect yourportable music player to thein-vehicle audio system. This allowsthe audio from a portable

• If the battery was removed, clean the battery cable ends and inspect.If you have any concerns or issues, contact your authorized dealer.MOTORCRAFT姞

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord Part Name orEquivalentFord Part Number /Ford SpecificationBrake/Clutch fluidTop-off

Item CapacityFord Part Name orEquivalentFord Part Number /Ford SpecificationEngine coolant5.8 quarts(5.5L)•Motorcraft威 SpecialtyOrange Engine Coolant

ENGINE DATAEngine 1.6L engineCubic inches 97Required fuel Minimum 87 octaneFiring order 1–3–4–2Ignition system Distributorless Ignition System(D.I.S.)

Engine drivebelt routingIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations req

Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX

TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C

Peace of mind•Keyless entry keypad •Seat covers*•Remote start •Windshield wiper shaker*•Wheel locks •Vehicle tracking and recovery*•Back-up camera* •B

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 30 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the

WARNING: Store the portable music player in a secure location,such as the center console or the glove box, when the vehicle isin motion. Hard objects

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan3312011 Fiesta (fie)Owners Guide, 3rd PrintingUSA (fus)

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is

GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?This guide describes the scheduled maintenance required for yourvehicle. Carefully following

Ford strongly recommends the use of genuine Ford replacement parts.Parts other than Ford, Motorcraft威 or Ford-authorized remanufacturedparts that are

Genuine Ford and Motorcraft姞 replacement partsDealerships stock Ford and Motorcraft威 branded replacement parts.These parts meet or exceed Ford Motor C

Check every six monthsBattery connections; clean if necessaryBody and door drain holes for obstructions; clean if necessaryCooling system fluid level

what’s been checked, what’s okay, as well as those things that mayrequire future or immediate attention. The multi-point vehicle inspectionis one more

NORMAL SCHEDULED MAINTENANCE AND LOGThe following section contains the “Normal Schedule”. This schedule ispresented at specific mileage (kilometer) in

Miles (x 1,000) 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150Kilometers (x 1,000) 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240Months 12

Radio reception factors:There are three factors that can affect radio reception:• Distance/strength: The further you travel from an FM station, thewea

Every 20,000 miles(32,000 km)Replace cabin air filter (if equipped)Every 30,000 miles(48,000 km)Replace climate-controlled seat filter (ifequipped)Rep

Maintenance schedule logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDAT

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

SPECIAL OPERATING CONDITIONSIf you operate your vehicle primarily in one of the more demandingconditions listed below, you will need to have some item

Operating in dusty conditions such as unpaved or dusty roadsInspect frequently, service asrequired– Replace cabin air filter (if equipped)– Replace en

Special operating condition logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

EXCEPTIONSIn addition, there are several exceptions to the Normal Schedule. Theyare listed below:Normal vehicle axle maintenance❑Rear axles and power

ENGINE COOLANT CHANGE RECORDInitial change 6 years or 100,000 miles (160,000 km)(whichever comes first)After initial change Every 3 years or 50,000 mi

Do not use any irregular shapedCDs or discs with a scratchprotection film attached.CDs with homemade paper(adhesive) labels should not beinserted into

911 Assist™ ...65AAccessing and using your USBport ...79Accessing call history

lubricant specifications ...321parking ...239shift interlock ...244Break-in period ...

Doorscentral unlocking ...134Downloading unread textmessages ...58Driving under specialconditions

turning on and off ...106Head restraints ...147Heatingheating and air conditioningsystem ...

automatic dimming rearviewmirror ...126heated ...127side view mirrors (power) ..

Safetyrestraints ...153, 158–159, 161Belt-Minder威 ...162extension assembly ...160for adults ...

rotating ...209safety practices ...208sidewall information ...210snow tires and chain

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m

Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The

CONGRATULATIONSCongratulations on acquiring your new Ford Motor Company product.Please take the time to get well acquainted with your vehicle by readi

Welcome to the new world of ingenuity and passion - technology that isboth fun and functional. Welcome to SYNC威.For more information, please visit www

SYNC威. In addition, if you connect a media device, SYNC威 creates andretains an index of media content supported by SYNC威. SYNC威 alsorecords a short de

SYNC姞 voice recognition featureSYNC威 is equipped with an advanced interactive Voice Recognition (VR)system. This system allows you to perform many ope

If the system has a low confidence level of what was asked, it willprompt you to try again or ask for help.Note: Even with Confirmation prompts turned

• After pressing , wait until the tone sounds and LISTENING appearsin the radio display before speaking a command. Any commandspoken prior to this wil

Commands for voice settingsIn voice settings, you can customize the level of system interaction, helpand feedback. The system default settings include

Radio controlSteeringwheel / stalkcontrolFunctionPHONEPress to activate SYNC威 hands-freecalling or to answer an incomingcall.When in phone mode, press

Voice commands in phone modeWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends that

While in phone mode, you may also say “Menu” and then any ofthe following commands:• [Phone] settings [message]notification on• [Phone] settings [mess

At any time, you may say these commands:• SYNC • USB• Line in • Bluetooth Audio• Phone • Voice settings• Cancel• Vehicle health report (ifequipped, U.

Protecting the environmentWe must all play our part inprotecting the environment. Correctvehicle usage and the authorizeddisposal of waste, cleaning a

The first thing you must do to use the system is to ’pair’ your Bluetooth威enabled phone with your vehicle’s SYNC威 system. This process allowsyour phon

Note: You can also manually enter the desired number by pressing thepresets (0–9).Ending a callAt any time, you can end an active phone call by pressi

3. When the desired selection appears in the display, press OK.If you choose Reply to Text Message, SYNC威 will take you back to thetext messaging menu

Putting a call on/off holdYou can put an active phone call on hold to have a private conversationwithin the vehicle cabin, or to answer another incomi

Note: SYNC威 supports a maximum of three callers on amultiparty/conference call.Accessing your call history and phone book during an active callNote: A

Phone redialPhone redial will prompt your cellular phone with Bluetooth wirelesstechnology to redial the last number called (if available).Note: To sc

Note: To scroll, press / .1. Press PHONE to enter Phone Menu.2. Scroll until Phonebook is selected and press OK.If there are fewer than 255 listings,

• Return6. Once your desired choice is selected, press OK. Refer to the followingspecific section(s) for further details on these options.Sending new

9. When the system asks if you want to send the message, press OK.SYNC威 will take you back to your inbox.Note: Each text message sent by SYNC威 will be

Under the phone settings menu on SYNC威, you can view the status ofyour paired phone with Bluetooth wireless technology, select fromvarious ring tones,

Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.WARNING: Please read the section Airbag Supple

Note: In-band ringing is a phone dependent feature. If your phonesupports in-band ringing, your phone’s ringer will play through thevehicle audio syst

• Download Phonebook: When Download Phonebook appears in theradio display, press OK. When Download? will appears in the display,press OK. The display

There is a free introductory period associated with the Traffic, Directionsand Information feature, but you must register to use this feature.Stay con

4. Once your destination is selected, a route is downloaded to yourvehicle.Turn by Turn Direction featuresOnce directions are downloaded, you can then

Personalizing Traffic, Directions and Information:Your Traffic, Directions and Information Services can be personalized toprovide quicker access to yo

911 Assist™ (if equipped)For 911 Assist™ to function properly, the vehicle must havebattery power after the crash, the cell phone must be previouslypa

911 ASSIST™ PRIVACY NOTICE: Once 911 Assist™ is enabled(set to ON), 911 Assist™ may, through any paired and connectedcell phone, disclose to emergency

The following steps are required for the 911 Assist™ feature to performproperly:• SYNC威 is on and functioning properly at the time of the incident and

Vehicle health report (if equipped, U.S. only)WARNING: Always follow scheduled maintenance instructions,regularly inspect your vehicle, and seek repai

your vehicle) and return to your account at www.SyncMyRide.com toview your report. Cell phone airtime usage may apply when reporting.To access and run

• How far (if at all) the driver was depressing the acceleratorand/or the brake pedal; and• How fast the vehicle was travelling; and• Where the driver

2. Scroll until Vehicle Health is selected and press OK.3. When User Preferences is selected, press OK.4. When Automatic Reports is selected, press OK

Adding (pairing) a phoneNote: This is a speed dependent feature and cannot be performed whenthe vehicle is traveling at speeds greater than 3 mph (5 k

1. Press PHONE to enter Phone Menu.2. Scroll until System Settings is selected and press OK.3. Scroll until Bluetooth Devices is selected and press OK

Deleting a phoneTo delete a paired phone from SYNC威:Note: To scroll, press/ .1. Press PHONE to enter Phone Menu2. Scroll until System Settings is sele

Changing the language settingSYNC威 allows you to select from three languages: English, French andSpanish. Once selected, all radio display messages an

1. Press PHONE to enter the Phone Menu.2. Scroll until System Settings is selected and press OK.3. Scroll until Advanced is selected and press OK.4. S

Voice commands when using the USB portWhen using the USB port, you may say any of the followingcommands:• Play all • Play• Pause • What’s playing?• Pl

Similar music: You can tell the system to play music ‘similar’ to whatyou are currently playing from the USB port. SYNC威 will use themetadata informat

1. Plug the device into the vehicle’s USB port.2. Press AUX repeatedly until SYNC威 USB appears in the radio display.3. Depending on how many digital m

To access:Note: To scroll, press/ .1. Press AUX repeatedly until SYNC威 appears.2. Press MENU to enter the Media Player Menu.3. Scroll to cycle through

Additionally, when you connect to Traffic, Directions andInformation (if equipped, U.S. only) the service uses GPStechnology and advanced vehicle sens

Note: Since your USB port allows you to charge your device (ifsupported by your device), SYNC威 will not automatically change mediamodes when something

4. Scroll until Select Source is selected and press OK.5. Scroll until Bluetooth Audio is selected and press OK. The display willshow the name of the

Repeat: Allows you to repeat any song.Autoplay: Allows you to listen to music which has already beenrandomly indexed during the indexing process.Note:

To access:1. Press AUX.2. Press MENU.3. When MediaPlayer Menu appears in the display, press OK.4. Use/ to cycle through the following options:• Play m

5. When Advanced is selected, press OK to select from:• Prompts • Install Application?• Languages • System Info• Factory Defaults •Return• Master Rese

Note: To scroll, press / .1. Press AUX repeatedly until SYNC appears.2. Press MENU. When Media Player Menu is selected, press OK.3. Scroll until Syste

3. Scroll until System Settings is selected and press OK.4. Scroll until Bluetooth Devices is selected and press OK.5. Scroll until Set Bluetooth On/O

3. Scroll until System Settings is selected and press OK.4. Scroll until Advanced is selected and press OK.5. Scroll until Prompts is selected and pre

6. When the system asks if you would like to restore the defaults pressOK. The display will then confirm when they are restored. SYNC威 willtake you ba

SYNC威 is able to organize and sort your indexed media from yourplaying device by metadata tags. Metadata tags are descriptive softwareidentifiers embe

EXPORT UNIQUE (NON–UNITED STATES/CANADA) VEHICLESPECIFIC INFORMATIONFor your particular global region, your vehicle may be equipped withfeatures and o

4. Scroll until Play Menu is selected and press OK. The system willbegin to play all the indexed media alphabetically. The first track titlewill appea

Selecting and playing specific albumsSYNC威 allows you view and play indexed media by ALBUMS. If you havefewer than 255 indexed albums, SYNC威 will list

2. Press AUX repeatedly until SYNC USB appears.3. Press MENU. When Media Player Menu is selected, press Ok.4. Scroll until Play Menu is selected and p

Playing a specific trackSYNC威 will allows you to search for and play a specific track which hasbeen indexed. If you have fewer than 255 indexed tracks

4. Scroll until Play Menu is selected and press OK.5. When Play All appears, scroll until Explore USB is selected and pressOK.6. Scroll to cycle throu

Note: With certain playing devices, if your metadata tags (Artist, Album,Track, Genre) are not populated, the tracks won’t be available in voicerecogn

Pairing: To use your Bluetooth enabled cellular phone with SYNC威, youmust go through a pairing (bonding) process. “Pairing” is a specialprocess used w

IF YOU DO NOT AGREE TO THIS END USER LICENSEAGREEMENT (“EULA”), DO NOT USE THE DEVICE OR COPYTHE SOFTWARE. ANY USE OF THE SOFTWARE, INCLUDINGBUT NOT L

the recipient agrees to the terms of this EULA. If the SOFTWARE isan upgrade, any transfer must include all prior versions of theSOFTWARE.• Terminatio

• Additional Software/Services: The SOFTWARE may permit FORDMOTOR COMPANY, third party software and service suppliers, MS,Microsoft Corporation, their