Ford 2011 F-150 v.2 Manuel d'utilisateur

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 18Message center 19Entertainment Systems 46AM/FM stereo 46AM/FM stereo with CD/M

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

The power point can switch to a fault mode when it is overloaded,overheated, or shorted. For overloading and shorting conditions, unplugyour device an

Press and pull the window switchesto open and close windows.• Press down (to the first detent)and hold the switch to open.• Pull up (to the first dete

Bounce-back override (front windows only)To override bounce-back, within two seconds after reaching bounce-backposition, if the switch is moved from t

Accessory delay (if equipped)With accessory delay, the window switches may be used for up to10 minutes after the ignition switch is turned to the off

EXTERIOR MIRRORSPower side view mirrors (if equipped)WARNING: Do not adjust the mirror while the vehicle is inmotion.To adjust your mirrors:1. Rotate

Fold-away mirrorsFold the side mirrors in carefullybefore driving through a narrowspace, like an automatic car wash.Powerfold mirrors (if equipped)Wit

On vehicles not equipped with rear defrost, press the heated mirrorcontrol located on the climate control panel. For more informationrefer to the Clim

Press and hold the rear of thecontrol to adjust the pedals towardyou. Press and hold the front of thecontrol to adjust the pedals away from you.WARNIN

Bounce-back:• If an object is in the way of the moving running board, the runningboard will automatically bounce back in the reverse direction andmove

Using speed controlsThe speed controls are located on the steering wheel. The followingbuttons work with speed control:– SET +: Press to set a speed o

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

Resuming a set speedPress and release RSM. This will automatically return the vehicle to thepreviously set speed.Increasing speed while using speed co

STEERING WHEEL CONTROLS (IF EQUIPPED)Radio control features– VOL + (Volume): Press todecrease or increase the volume.(Seek): Press to selectthe previo

For further information on the SYNC威 system, refer to the SYNC威supplement.Navigation system/SYNC威hands-free control features (ifequipped)Presscontrol

To open the moon roof: Press andrelease the SLIDE control, the moonroof will open automatically. Pressthe switch again to stop the moonroof.To close t

Car2U姞 Home Automation System (if equipped)The Car2U威 Home AutomationSystem is a universal transmitterlocated in the driver’s visor thatincludes two p

• Fixed code garage door openers were produced prior to 1996. Fixedcode uses the same coded signal every time. It is manuallyprogrammed by setting DIP

1. Firmly press the two outerCar2U威 system buttons for1–2 seconds, then release.2. Go to the garage to locate thegarage door opener motor and its“lear

After successful programming, you will be able to operate your Car2U威system by pressing the button you programmed to activate the opener.The indicator

Switchposition 12345678 9101112Up, onor +LLLLLLLLLLLLMiddle,neutralor 0MMMMMMMMMMMMDown,offor–RRRRRRRRRRRRL=left; M=middle; R=right3. To input these p

After successful programming, you will be able to operate your Car2U威system by pressing the button you programmed to activate the opener.The indicator

WARNING LIGHTS AND CHIMESBase instrument cluster shown in standard measure; metricsimilar. Uplevel clusters similar.Warning lights and gauges can aler

POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)WARNING: Do not install additional floor mats on top of thefactory installed floor mats as they may interfer

1. Before removal of the tailgate,locate and disconnect the tailgatein-line connector under the pickupbox on the passenger side of thevehicle near the

Tailgate step (if equipped)Your vehicle may be equipped with a feature that allows easier entry intothe truck bed. To open the tailgate step:1. Flip d

Note:• Fully close and latch the tailgate step before moving the vehicle.• Never drive with the step or grab handle deployed.• Replace slip resistance

To stow the box side step, with your foot, push the box side step underthe truck until fully latched. Do not push on the button while stowingthe box s

2. Open the latches to release thepanels.3. Rotate the panels toward thetailgate.Repeat Steps 1–3 for the other side of the bed extender.4. Connect th

5. Ensure the latch rod is insertedinto the tailgate hole and the lockingpins on both sides are engaged intotheir holes in the pick-up box.6. Reverse

CARGO MANAGEMENT SYSTEM (IF EQUIPPED)The cargo management system consists of the Cargo rail package withthe following as optional accessories:• Front

Note: When replacing a cleat into the rail, make sure the oval embossedon the knob is not upside down. This will ensure that the cleat isproperly orie

Cross bars: Aluminum cross bars with T-slot channels in all four sides,and a latch mechanism that allows the end supports to snap over theexisting cle

Uplevel message centerNote: Some warning lights arereconfigurable telltale (RTT)indicator lights and will illuminate inthe message center. These light

Bed divider: This panel will keep small items up to 400 lb (180 kg) inposition in the pickup box. Also includes T-slots to allow attachment ofindustry

Side mounted tool bins: Watertight bins can be positioned at any pointalong the side rails and can be easily removed (even when full), andcarried to w

• To remove the bin from the rail, open lid and pull up on both leverslocated on the outboard edge (next to the pickup box top rail) untilthe handles

KEYSYour vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and

MyKey威 restricted featuresStandard settings – These settings cannot be changed•The audio system will be muted whenever Belt-Minder威 is activateduntil

For optional message center:1. At the main menu screen select SETTING then MYKEY by pressingOK or the right arrow key.2. Press OK to select CREATE MYK

For optional message center:1. At the main menu screen select SETTING then MYKEY by pressingOK or the right arrow key.2. Use the up and down arrows to

Refer to Message center in the Instrument Cluster chapter for MyKey威system warnings displays.Using MyKey威 with remote start systemsMyKey威 is not compa

Note: For all vehicles, the number of MYKEY(S) PROGRAMMED orADMIN KEYS PROGRAMMED that is displayed in the MyKey威 systemstatus menus will include the

TroubleshootingCondition Potential CausesCan’t create a MyKey威 • Key in the ignition is already aMyKey威.• Key in the ignition is the lastremaining adm

Powertrain malfunction/Reducedpower/Electronic throttlecontrol (RTT): Displays when theengine has defaulted to a“limp-home” operation or when a transm

Condition Potential CausesI accidentally programmed allkeys as MyKeys威• Vehicle has a non Ford-approvedremote start system that is recognizedas an adm

POWER DOOR LOCKS (IF EQUIPPED)Press control to unlock all doors.Press control to lock all doors.Smart locks (if equipped)This feature prevents you fro

The autolock feature repeats when:• any door is opened then closed while the ignition is in the on positionand the vehicle speed is 9 mph (15 km/h) or

Keyless entry keypad autolock enable/disable procedure1. Turn the ignition to the offposition.2. Close all the doors.3. Enter factory–set 5–digit entr

Power door lock switch autounlock enable/disable procedureBefore starting, ensure the ignition is in the off position and all vehicledoors are closed.

CHILDPROOF DOOR LOCKS (ON VEHICLES WITH REAR DOORS)• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be o

The typical operating range for your IKT is approximately 33 feet(10 meters). A decrease in operating range could be caused by:• weather conditions,•

Switching from two step to one step door unlockingYour vehicle comes with two step unlocking enabled. Unlocking can beswitched between two step and on

2. Press and hold control button 1for five seconds. A tone will beheard after two seconds confirmingmemory position has been set.Continue to hold unti

4. Insert the new battery. Refer to the instructions inside the IKT for thecorrect orientation of the battery. Press the battery down to ensure thatth

Airbag readiness: If this light failsto illuminate when the ignition isturned to on, continues to flash orremains on, have the systemserviced immediat

Remote start (if equipped)Your vehicle may be equipped with the remote start feature which allowsyou to start the engine from outside the vehicle. If

The parking lamps will remain on and the engine will run for 5, 10, or15 minutes, depending on how you programmed the system. To selectthe duration of

3. Enter your personal 5-digit code. Each number must be enteredwithin five seconds of each other.4. To associate the entry code with a memory setting

Unlocking and locking the doors using keyless entryTo unlock the driver’s door, enter the factory set 5-digit code or yourpersonal code. Each number m

Replacement keysIf your keys are lost or stolen and you don’t have an extra coded key,you will need to have your vehicle towed to an authorized dealer

5. After three seconds but within 10 seconds of removing the secondcoded key, insert the new unprogrammed key (new key/valet key) intothe ignition and

The turn signal lamps will flash once when all doors and the hood areclosed indicating the vehicle is locked and entering the 20 secondcountdown.Disar

FRONT SEATSWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the eve

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint by pulling up

Front seat• Lift the track release bar to movethe seat forward or rearward.Make sure that the seat isrelatched into place.Seating and Safety Restraint

Low tire pressure warning:Illuminates when your tire pressureis low. If the light remains on atstart up or while driving, the tirepressure should be c

• Pull the release lever handlelocated on the side of the seat upto move the seatback forward orbackward.Using the armrest (if equipped)• Push the rel

• To gain access to the storagecompartment (if equipped) inyour armrest, lift the latch toopen the lid.Using the manual lumbar support (if equipped)Fo

Using the power lumbar support (if equipped)The power lumbar control is located on the outboard side of the seat.Press the forward side of the control

The control is located on the outboard side of the seat cushion.Move the switch to raise or lowerthe front or rear portion of the seatcushion.Move the

• To program position 1, move the memory features to the desiredpositions using the associated controls. Press and hold button 1 for atleast two secon

travel to the desired memory setting less 2 inches (5 cm). Once enteringthe vehicle and inserting the key in the ignition while in P (Park), theeasy e

Note: Do not do the following:• Place heavy objects on the seat• Operate the seat heater if water or any other liquid is spilled on theseat. Allow the

To operate the heated seats:Press the heated seat symbol tocycle through the various heatsettings and off. Warmer settings areindicated by more indica

To remove an air filter:1. Turn the vehicle off.2. Push up on the outside rigid edgeof the filter until the tabs arereleased, then rotate the air filt

WARNING: The adjustable head restraint is a safety device.Whenever possible it should be installed and properly adjustedwhen the seat is occupied.The

ignition is turned on, or remains on, have the system servicedimmediately by your authorized dealer.Four-wheel drive high (RTT) (ifequipped): Displays

Returning the seat to seating positionWARNING: Make sure that cargo or any objects are not trappedunderneath the seat cushion before returning the sea

1. Pull control on the bottom of theseat cushion to release seat cushionfrom storage position.2. Push seat cushion down until itrests into the horizon

Rear heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cord

SAFETY RESTRAINTSPersonal Safety System™The Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupan

Driver and passenger dual-stage airbag supplemental restraintsThe dual-stage airbags offer the capability to tailor the level of airbaginflation energ

WARNING: When possible, all children 12 years old and undershould be properly restrained in a rear seating position.The front passenger sensing system

The Restraints Control Module (RCM) monitors its own internal circuitsand the circuits for the airbag supplemental restraints, crash sensor(s),safety

WARNING: In a rollover crash, an unbelted person issignificantly more likely to die than a person wearing a safetybelt.WARNING: Each seating position

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.Safety belt with cinch tongue (front center seat only)The cinch tongue wil

3. Insert the belt tongue into the proper buckle for your seating positionuntil you hear a snap and feel it latch.4. Make sure the tongue is securely

GAUGESBase cluster with automatic transmission shown; metric similar.Uplevel clusters similar.1. Engine oil pressure gauge: Indicates engine oil press

Pregnant women should alwayswear their safety belt. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips

Automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt

WARNING: BELT AND RETRACTOR ASSEMBLY MUST BEREPLACED if the safety belt assembly “automatic lockingretractor” feature or any other safety belt functio

WARNING: The Personal Safety System威 provides the mostbenefit to belted occupants. The system monitors and tailors theairbag deployment based upon saf

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war

The Belt-Minder威 feature uses two different warning chimes. During thefirst minute of activation, the warning chime will sound once everysecond. The r

The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra

Reasons given... Consider...“I’d rather be thrownclear”Not a good idea. People who are ejectedare 40 times more likely to DIE. Safetybelts help preven

1. Turn the ignition switch to the on position. DO NOT START THEENGINE.2. Wait until the safety belt warning light turns off. (Approximately oneminute

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The airbag supplemental restraint system is designed to work inconjunction with the safety belts to help pro

3. Fuel gauge: Indicates approximately how much fuel is left in the fueltank (when the ignition is in the on position). The fuel gauge may varyslightl

Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in

WARNING: Do not attempt to service, repair, or modify theairbag supplemental restraint systems or its fuses. Contact yourauthorized dealer as soon as

If two adults and a child occupy a Regular Cab, properly restrain thechild in the center front unless doing so would interfere with driving thevehicle

internal injuries, particularly to occupants who are not properlyrestrained or are otherwise out of position at the time of airbagdeployment. Thus, it

The front passenger sensing systemuses a ⬙passenger airbag off⬙ or⬙pass airbag off⬙ indicator which willilluminate and stay lit to remind youthat the

• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LampPasseng

ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase,

A difficulty with the system is indicated by one or more of the following:• The readiness lights will eitherflash or stay lit.• The readiness lights w

How does the side airbag system work?The design and development of theside airbag system includedrecommended testing proceduresthat were developed by

WARNING: Several airbag system components get hot afterinflation. Do not touch them after inflation.WARNING: If the sideairbag has deployed, theairbag

Locks and Security 133Keys 133Locks 141Anti-theft system 153Seating and Safety Restraints 157Seating 157Safety restraints 173Airbags 189Child restrain

Info (information menu)Press the INFO button repeatedly tocycle through the following features:TRIP A/BRegisters the distance of individual journeys.

Safety Canopy姞 SystemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a deploying

How does the Safety Canopy姞 System work?The design and development of theSafety Canopy system includedrecommended testing proceduresthat were develope

The Safety Canopy is mounted to roof side-rail sheet metal, behind theheadliner, above each row of seats. The Safety Canopy is designed toinflate betw

A difficulty with the system is indicated by one or more of the following:• The readiness light (same light as for front airbag system) will eitherfla

SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle.If the child is the proper height, age, and weigh

Installing child safety seats with combination lap and shoulderbeltsCheck to make sure the child seat is properly secured before each use.Children 12

• Differences in the automatic shut-off points on the fuel pumps atservice stations• Variations in top-off procedure from one fill-up to another• Roun

If you are using a front center seat, see Installing child safety seats incinch tongue combination lap and shoulder belt seating positionlater in this

3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi

8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up

1. Position the child safety seat inthe center front seat.2. If the center lap/shoulder safetybelt has been disconnected from theseat to carry large c

5. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear

9. Before placing the child into thechild seat, forcibly pull the childseat forward and back to make surethat the seat is held securely inplace. To ch

Your vehicle is equipped with LATCH lower anchors for child seatinstallation at the following seating positions (LATCH is not available onF150 Regular

Use of inboard lower anchors from the outboard seating positions(center seating use)The lower anchors at the center of the second row rear seat are sp

The passenger seats of your vehicle are equipped with built-in tetherstrap anchors located behind the seats as described below.The tether anchors in y

Once the child safety seat has been installed using either the safety belt,the lower anchors of the LATCH system, or both, you can attach the toptethe

System check and vehicle feature customizationPress the SETUP button repeatedlyto cycle the message center throughthe following features:RESET FOR SYS

Rear seat tether strap attachment (SuperCab and SuperCrew)There are three loops of webbingjust above the back of the rear seat(along the bottom edge o

3. Tighten the tether strapaccording to the child seatmanufacturer’s instructions.If the safety seat is not anchored properly, the risk of a child bei

When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the

• High back booster seatsIf, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo

If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat may improve thisconditio

WARNING: Failure to inspect and if necessary replace thesafety belt assembly or child restraint system under the aboveconditions could result in sever

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary

• Narrower – to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUVs and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

OIL LIFEThis displays the remaining oil life.An oil change is required whenever indicated by the message center andaccording to the recommended mainte

Glossary of tire terminology• Tire label: A label showing the OE (Original Equipment) tire sizes,recommended inflation pressure and the maximum weight

Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure of all tires and adjust ifrequired

When weather temperature changes occur, tire inflation pressures alsochange. A 10°F (6°C) temperature drop can cause a corresponding dropof 1 psi (7 k

TIRE CAREInspecting your tires and wheel valve stemsPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones

WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressur

WARNING: Only use replacement tires and wheels that are thesame size, load index, speed rating and type (such as P-metricversus LT-metric or all-seaso

It is recommended that the two front tires or two rear tires generally bereplaced as a pair.The tire pressure sensors mounted in the wheels (originall

Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your

WARNING: If the tire label shows different tire pressures forthe front and rear tires and the vehicle is equipped with TPMS(tire pressure monitoring s

5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new tires to match the new wheeldiameter

EASY ENTRYThis feature automatically moves the driver’s seat backwards for easyexit/entry from the vehicle.Press the RESET button to turn the easy ent

numbers represent the week and year the tire was built. For example,the numbers 317 mean the 31st week of 1997. After 2000 the numbersgo to four digit

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Understanding your tire pressure monitoring system (TPMS)The tire pressure monitoring system measures pressure in your four roadtires and sends the ti

When you believe your system is not operating properlyThe main function of the tire pressure monitoring system is to warn youwhen your tires need air.

Low tire pressurewarning lightPossible cause Customer action requiredFlashing warninglightSpare tire inuseYour temporary spare tire is inuse. Repair t

TPMS reset procedureThe TPMS reset procedure needs to be performed after each tirerotation on vehicles that require different recommended tirepressure

3. Cycle the ignition to the onposition with the engine off.4. Turn the hazard flashers on thenoff three times. This must beaccomplished within 10 sec

Types of messages and warnings:• Some messages will appear briefly to inform you of something youmay need to take action on or be informed of.• Some m

8. Remove the valve cap from the valve stem on the right rear tire;decrease the air pressure until the horn sounds.9. Remove the valve cap from the va

Follow these guidelines when using snow tires and chains:• If possible, avoid fully loading your vehicle.• Use only SAE Class S chains.• Install chain

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400

Note: Do not exceed trailer weight of 5,000 lb (2,268 kg) when towingwith bumper only.Exceeding the maximum GCWR could result in extensive damageto yo

TURN POWER OFF TO SAVE BATT (if equipped) — Displayedwhen the battery management system determines that:• the battery is at a low state of charge or,•

Regular CabEngine Rear axleratioMaximumGCWR - lb (kg)Maximum TrailerWeight - lb (kg)2WD 126” wheelbase3.7L3.55 10400 (4717) 5500 (2495)3.73 10900 (494

SuperCabEngine Rear axleratioMaximumGCWR - lb (kg)Maximum TrailerWeight - lb (kg)2WD 145” wheelbase3.5L 3.15 14000 (6350) 8600 (3901)3.55 15200 (6895)

SuperCrewEngine Rear axleratioMaximumGCWR - lb (kg)Maximum TrailerWeight - lb (kg)2WD 145” wheelbase3.5L 3.15 14000 (6350) 8500 (3856)3.55 15300 (6940

SuperCrewEngine Rear axleratioMaximumGCWR - lb (kg)Maximum TrailerWeight - lb (kg)5.0L3.55 13500 (6123) 7900 (3583)3.73 14900 (6759) 9300 (4218)4WD 15

4. Measure the height of the top of the front wheel opening on thefender a second time, this is H2.5. Install and adjust the tension in the weight dis

WARNING: The Ford TBC has only been verified to becompatible with trailers having electric-actuated drum brakes(one to four axles) and not hydraulic s

• TRAILER DISCONNECTED: This message is displayed andaccompanied by a single chime, when a trailer connection wasdetermined and then a disconnection,

5. In a traffic-free environment, tow the trailer on a dry, level surface ata speed of 20–25 mph (30–40 km/h) and squeeze the manual controllever comp

• Avoid towing in adverse weather conditions. The TBC does notprovide anti-lock control of the trailer wheels. Trailer wheels can lockup on slippery s

Driving while you towWhen towing a trailer:• Do not drive faster than 70 mph (113 km/h) during the first 500 miles(800 km) of trailer towing and don’t

TRACTION CONTROL OFF (if equipped) — Displayed when thetraction control has been disabled by the driver. Refer to the Drivingchapter for more informat

Launching or retrieving a boatDisconnect the wiring to the trailer before backing the trailerinto the water. Reconnect the wiring to the trailer after

4WD vehicles equipped with a manual-shift transfer case:• Release the parking brake.• Turn the key in the ignition to the off position.• Place the tra

STARTINGPositions of the ignition1. Off — locks the automatictransmission gearshift lever andallows key removal. Note: In orderto switch off the engin

WARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine compartment and exhaus

3. Make sure the gearshift is in P(Park).4. Make sure the parking brake isset.5. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warni

Starting the engine1. Turn the key to 3 (on) withoutturning the key to 4 (start).2. Turn the key to 4 (start), thenrelease the key as soon as theengin

If you should experience cold weather starting problems on E85ethanol,and neither an alternative brand of E85ethanol nor an engine blockheater is avai

WARNING: Failure to follow engine block heater instructionscould result in property damage or physical injury.WARNING: To reduce the risk of electrica

• Finally, have the engine block heater system checked during your falltune-up to be sure it’s in good working order.How to use the engine block heate

Using ABSWhen hard braking is required, apply continuous force on the brakepedal. Do not pump the brake pedal since this will reduce theeffectiveness

TO EXIT 4X4 LOW SLOW TO 3 MPH (if equipped) — Displayedwhen 2WD is selected while the vehicle is operating in 4X4 LOW. Formore information, refer to F

WARNING: Always set the parking brake fully and make surethat the gearshift is securely latched in P (Park) (automatictransmission) or in 1 (First) (m

WARNING: Remember that even advanced technology cannotdefy the laws of physics. It’s always possible to lose control of avehicle due to inappropriate

When AdvanceTrac威 with RSC威 performs a normal system self-check,some drivers may notice a slight movement of the brake, and/or arumble, grunting, or g

Electronic stability control (ESC)Electronic stability control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa

Switching off AdvanceTrac威 with RSC威If the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off certain features of the

AdvanceTrac威 with RSC威 FeaturesButtonfunctionsStabilitycontrol OFFlightRSC威 ESC TCSButton pressedagain afterdeactivationNotilluminatedEnabled Enabled

During trailer sway control events, the stability control light in theinstrument cluster will flash momentarily. The message center will alsodisplay T

WARNING: The EPS system has diagnostics checks thatcontinuously monitor the EPS system to ensure proper operationof the electronic system. When an ele

All enginesIf the steering wanders or pulls equipped with either an EPS or ahydraulic steering system, check for:• an improperly inflated tire• uneven

Utility vehicles and trucks have larger tires and increased groundclearance, giving the vehicle a higher center of gravity than a passengercar.WARNING

VEHICLE SPEED 80 MPH MAX — Displayed when a MyKey威 is inuse and the Admin has enabled the MyKey speed limit and the vehiclespeed is 80 mph (130 km/h).

2. Move the shift lever boot bypressing on the edges and moving itup the gearshift lever.3. Turn the steering wheel one-halfturn to access the slots o

5. With the ignition in the onposition, pull back on the BSIsolenoid found on top of theuncovered steering column and atthe same time, apply the brake

If the fuse is not blown and the brake lamps are working properly, thefollowing procedure will allow you to move the gearshift lever from P(Park):1. A

AUTOMATIC TRANSMISSION OPERATIONUnderstanding the shift positions of the 6-speed automatictransmissionThis vehicle is equipped with an adaptive transm

D (Drive) with Tow/Haul OffThe normal driving position for the best fuel economy. Transmissionoperates in gears one through six.D (Drive) with Tow/Hau

To deactivate the tow/haul feature and return to normal driving mode,press the button on the end of the gearshift lever. The TOW HAUL lightwill no lon

PRS (Progressive RangeSelection)With the gearshift lever in D(Drive), press the – button to activePRS. The available and selectedgears will be indicat

Recommended shift speedsUpshift according to the following chart:Upshifts when acceleratingShift from:1 – 2 15 mph (24 km/h)2 – 3 25 mph (40 km/h)3 –

WARNING: To help avoid personal injury, please read andunderstand the limitations of the reverse sensing system ascontained in this section. Reverse s

The RSS detects obstacles up to6 feet (2 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the fi

Customer Assistance 348Reporting safety defects (U.S. only) 355Reporting safety defects (Canada only) 355Cleaning 356Maintenance and Specifications 36

SLOW VEHICLE TO XX MPH FOR ELD (if equipped) — Displayedwhen the vehicle speed requirement for the electronic lockingdifferential mode has not been me

Keep the RSS sensors (located on the rear bumper/fascia) freefrom snow, ice and large accumulations of dirt (do not clean thesensors with sharp object

Visual park aid alert (if equipped)Visual park aid alert allows the driver to see the area that is causing thereverse sensing system to beep. The visu

When towing, the reverse camera system will only see what is beingtowed behind the vehicle. This might not provide adequate coverage as itusually prov

Press and on the steeringwheel controls to select a zoomoption. You can choose from OFF,Level 1, Level 2 and Level 3. Usethe OK button to make a selec

The camera lens for the reverse camera system is located on the tailgate.Keep the lens clean so the video image remains clear and undistorted.Clean th

• If the image is not clear, then check if there is anything covering thelens such as dirt, mud, ice, snow, etc. If the image is still not clearafter

FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED)WARNING: For important information regarding safe operationof this type of vehicle, see Preparing to dri

• CHECK 4X4 - Displays when a4X4 fault is present.Note: When a 4X4 system fault is present, the system will typicallyremain in whichever 4X4 mode was

3. Move the transfer case lever through N (Neutral) directly to thedesired position.• If the transfer case will not engage into 4L (4X4 low) do not fo

4L (4X4 Low) - Uses extra gearing to provide maximum power to allfour wheels at reduced speeds. Intended only for off-road applicationssuch as deep sa

The message center display is located in the instrument cluster. Use thesteering wheel mounted buttons to navigate through the message center.Press th

Note: Some noise may be heard as the system shifts or engages; this isnormal.Note: 4x4 low mode is not intended for use on dry pavement.Using the all-

Shifting between AWD (auto) and 4H (high)Move the control from AWD to 4H at a stop or while driving at anyspeed. The message center will display “AWD”

Activating the electronic locking differential (ELD)The ELD can be turned on bypulling the knob on the 4WD controltoward you while the control is inei

For vehicles equipped with a 3.5L Ecoboost™ engine:Your vehicle is equipped with an underbody transmission shield andbrackets that may become damaged

• It may be safer to stay on the apron or shoulder of the road and slowdown gradually before returning to the pavement. You may losecontrol if you do

Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,

WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your author

Mud and waterIf you must drive through highwater, drive slowly. Traction orbrake capability may be limited.When driving through water,determine the de

Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should

Driving on snow and ice4WD vehicles have advantages over 2WD vehicles in snow and ice butcan skid like any other vehicle.Should you start to slide whi

Scroll up/down to highlight one of the options, then press the right arrowkey or OK to enter into that menu option.Gauge ModeGauge Detail: In this mod

Any modifications to a vehicle that raise the center of gravity can makeit more likely the vehicle will roll over as a result of a loss of control.For

ROADSIDE ASSISTANCEVehicles sold in the U.S. : Getting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany off

Vehicles sold in the U.S. : Using roadside assistanceComplete the roadside assistance identification card and place it in yourwallet for quick referen

FUEL PUMP SHUT-OFFIn the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fue

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

To reinstall the fuse box cover, place the top part of the cover on thefuse panel, then push the bottom part of the cover until you hear it clickshut.

Fuse/RelayLocationFuse AmpRatingProtected CircuitsNavigation display10 10A Run/accessory relay11 10A Instrument cluster12 15A Interior lighting, Puddl

Fuse/RelayLocationFuse AmpRatingProtected Circuitsswitch, Rear video, Off roadindicator (SVT Raptor)35 5A Hill descent switch (SVT Raptor)36 10A Restr

WARNING: To reduce risk of electrical shock, always replacethe cover to the power distribution box before reconnecting thebattery or refilling fluid r

Fuse/RelayLocationFuse AmpRatingProtected Circuits1240A** Electric fan50A** Electric fan (6.2L with max trailertow, SVT Raptor)13 30A** Starter relay

If you calculate your average fuel economy by dividing miles traveled bygallons of fuel used (liters of fuel used by 100 kilometers traveled), yourfig

Fuse/RelayLocationFuse AmpRatingProtected Circuits36 30A** Roll stability control(RSC)/Anti-lock brake system(ABS)37 — TT left stop/turn relay38 — TT

Fuse/RelayLocationFuse AmpRatingProtected Circuits61 — Not used62 — Wiper motor relay63 25A** Electric fan64 40A** Vacuum pump relay power (3.5Lengine

Fuse/RelayLocationFuse AmpRatingProtected Circuits78 15A* PCM – Voltage power4–Ignitioncoils (3.5L, 3.7L, 5.0L engines)20A* PCM – Voltage power4–Ignit

CHANGING THE TIRESIf you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel

A dissimilar spare tire/wheel is defined as a spare tire and/or wheel thatis different in brand, size or appearance from the road tires and wheelsand

The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following:• Handling, stability and braking performance• Comfort and

Location of the spare tire and toolsThe spare tire is located under the vehicle, just forward of the rearbumper. The jack, jack handle and lug wrench

2. Fully insert the jack handlethrough the bumper hole and intothe guide tube through the accesshole in the rear bumper.3. Turn the handle countercloc

4. Loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground.Note: For F-150 SVT Raptor, i

• RearNote: Never use the front or reardifferential as a jacking point.WARNING: To lessen the risk of personal injury, do not put anypart of your body

Truck Apps (if equipped)In this mode, off-road and trailer towing application options are available.*Off RoadPitch and bank angle (in degrees): Displa

9. Remove the jack and fully tightenthe lug nuts in the order shown(Refer to Wheel lug nut torquespecifications later in this chapterfor the proper lu

3. Turn the jack handle clockwise until the tire is raised to its stowedposition underneath the vehicle. The effort to turn the jack handleincreases s

Note: Inspect the wheel pilot holeprior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean r

Preparing your vehicleWhen the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a

1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery.2. Connect the other end of thepositive (+) cable to the

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.Note: In the illustration, the vehicle on the bottom i

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

Emergency towingIn case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport veh

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehi

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

When “Press OK for options” is displayed, pressing OK will open thetrailer options menus:TrailerChange ActiveTrailerWhen this is highlighted, press th

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

LINE before exercising rights or seeking remedies created by the FederalMagnuson-Moss Warranty Act, 15 U.S.C. sec. 2301 et seq. If you chooseto seek r

You can get more information by calling BBB AUTO LINE at1-800-955-5100, or writing to:BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia

The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emission control system and may causeengine knock

If your vehicle must be serviced while you are traveling or living in theMiddle East, contact the nearest authorized dealer. If the authorizeddealer c

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

• Never use abrasive materials such as steel wool or plastic padsas they can scratch the chrome surface.WAXING• Wash the vehicle first.• Use a quality

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

3.7L engineCleaning3592011 F-150 (f12)Owners Guide, 2nd PrintingUSA (fus)

TrailerReset TrailerMileage /Kilometers (ifequipped)Press the right arrow button when this is highlighted todisplay accumulated distance on a given tr

5.0L engineCleaning3602011 F-150 (f12)Owners Guide, 2nd PrintingUSA (fus)

6.2L engineCleaning3612011 F-150 (f12)Owners Guide, 2nd PrintingUSA (fus)

3.5L Ecoboost™ enginePLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your auth

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft威 Premium Windshield Washer Concentrate (ZC-32-A) inthe U.S., or Premiu

For removal of fine scuffs and scratches, use Scotch-Brite威 MicrofiberCloth or cheese cloth along with Motorcraft Premium Liquid Wax(ZC-53-A), Motorcr

If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows:1. Wipe up spilled liqui

LEATHER SEATS(IF EQUIPPED, EXCEPT FOR THE KING RANCH姞 EDITION)For King Ranch威 leather seats, refer to a separate section in thischapter.• Clean spills

ScratchesNatural Markings - Because the leather in the seat comes from genuinesteer hides, there will be evidence of naturally occurring markings, suc

FORD AND LINCOLN CAR CARE PRODUCTSYour Ford or Lincoln authorized dealer has many quality productsavailable to clean your vehicle and protect its fini

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

VehicleMenu ControlStandard: with standard set, pressing the up/downarrows from a lower level menu will escape to themain menu.Memory On: with memory

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel.2. Go to the front of the vehicle a

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.7L V6 engine1. Windshield washer fluid reservoir2. Battery3. Engine oil dipstick (out of view)4. Bra

5.0L V8 engine1. Windshield washer fluid reservoir2. Battery3. Engine oil filler cap4. Engine oil dipstick5. Brake fluid reservoir6. Engine coolant re

6.2L V8 engine1. Windshield washer fluid reservoir2. Engine oil dipstick3. Brake fluid reservoir4. Engine coolant reservoir5. Air filter assembly6. Po

3.5L V6 EcoBoost™ engine1. Windshield washer fluid reservoir2. Battery3. Engine oil filler cap4. Engine oil dipstick5. Brake fluid reservoir6. Engine

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice

2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler cap

Change your engine oil according to the appropriate schedule listed inthe scheduled maintenance information.Ford production and Motorcraft威 replacemen

It is recommended you use the appropriate Motorcraft威 oil filter oranother with equivalent performance for your engine application.BATTERYYour vehicle

UnitsUnits English or MetricSystem ResetHold OK to Reset System to Factory DefaultInformationIn this mode, you can view different vehicle system infor

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

If the battery has been disconnected or a new battery has been installed,the clock and radio settings must be reset once the battery isreconnected.• A

in some cases after charging battery with the external charger, the BMSrequires eight hours of vehicle sleep time (key off with doors closed) torelear

If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the reservoir islow or

• Do not add extra inhibitors or additives to the coolant. Thesecan be harmful and compromise the corrosion protection of the enginecoolant.For vehicl

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your coolin

• If available, refer to the chart on the coolant container toensure the coolant concentration in your vehicle will provideadequate protection at the

When fail-safe mode is activatedYou have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be ab

You may notice a reduction in the vehicle’s speed caused by reducedengine power. Your vehicle has been designed to enter this mode ifcertain high temp

FUEL FILTERYour vehicle is equipped with a lifetime fuel filter that is integrated withthe fuel tank. Regular maintenance or replacement is not needed

System warnings and status messagesSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems.In the event of a

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek med

WARNING: Flexible fuel components and standard unleadedgasoline fuel components are not interchangeable. If your vehicleis not serviced in accordance

• DO NOT use a device that would hold the fuel pump handle in the fillposition.Easy Fuel姞 “no cap” fuel systemYour fuel tank is equipped with an Easy

WARNING: The fuel system may be under pressure. If you heara hissing sound near the fuel filler door (Easy Fuel威 “no cap”fuel system), do not refuel u

Some stations offer fuels posted as⬙Regular⬙ with an octane ratingbelow 87, particularly in highaltitude areas. Fuels with octanelevels below 87 are n

Do not add aftermarket fuel additive products to your fuel tank. Itshould not be necessary to add any aftermarket products to your fueltank if you con

Refilling with a portable fuel containerWith the Easy Fuel威 “no cap” fuel system, use the following directionswhen filling from a portable fuel contai

ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform

Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers).2. Each time you fill the tan

• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between the top gears occurs. Unnecessaryshifting of this type co

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

TURN POWER OFF TO SAVE BATTERY (if equipped) — Displayedwhen the battery management system determines that:• the battery is at a low state of charge o

EMISSION CONTROL SYSTEMYour vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to co

Do not make any unauthorized changes to your vehicle or engine. Bylaw, vehicle owners and anyone who manufactures, repairs, services,sells, leases, tr

Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect

POWER STEERING FLUID (6.2L V8 ENGINE ONLY)Check the power steering fluid. Refer to scheduled maintenanceinformation.1. Start the engine and let it run

TRANSMISSION FLUIDChecking 6-speed automatic transmission fluidThe automatic transmission does not have a transmission fluid dipstick.Refer to your sc

AIR FILTERRefer to scheduled maintenance information for the appropriateintervals for changing the air filter element.When changing the air filter ele

3. Clean the area around the airtube to air cover connection toprevent debris from entering thesystem and then loosen the bolt onthe air tube clamp so

8. Replace the air filter housingcover and secure the clamps. Becareful not to crimp the filterelement edges between the air filterhousing and cover a

VEHICLE STORAGEIf you plan on storing your vehicle for an extended period of time(30 days or more), refer to the following maintenance recommendations

Note: During extended periods of vehicle storage (30 days or more),fuel may deteriorate due to oxidation. Add a quality gas stabilizerproduct to the v

ENGINE OIL CHANGE SOON — Displayed when the engine oil liferemaining is 5% to 1%.OIL CHANGE REQUIRED — Displayed when the oil life left reaches0%.LOW

• Check tire pressures and set tire inflation per the Tire Label.• Check brake pedal operation. Drive the vehicle 15 ft (4.5 meters) backand forth to

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord part name orequivalentFord part number /Ford specificationBrake fluidBetweenMIN/MAX

Item CapacityFord part name orequivalentFord part number /Ford specification3.7L engine coolant 16.0 quarts (15.1L)•Motorcraft威 SpecialtyOrange Engine

Item CapacityFord part name orequivalentFord part number /Ford specificationAutomatic transmissionfluid (6R80)12.1 quarts(11.7L)6(3.7L engine)Motorcra

Item CapacityFord part name orequivalentFord part number /Ford specificationFuel tank SuperCrew 6.5’box26.0 gallons(98.4L) Standard36.0 gallons(136.2L

ENGINE DATAEngine3.7L V6Engine5.0L V8Engine6.2L V8Engine3.5L V6EcoBoost™EngineCubicinches226 302 378 214FuelMinimum87 octaneor E85Minimum87 octaneor E

6.2L engine3.5L EcoBoost™ engineIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulat

Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX

TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C

SERVICE POWER STEERING — The power steering system hasdetected a condition that requires service.SERVICE POWER STEERING NOW — The power steering syste

•Towing mirrors •Rear seat entertainment*•Portable navigation* •Trailer brake controller•Bed extender •Hitch ball and towbars•Tonneau covers*•Interior

• The Federal Communications Commission (FCC) and Canadian RadioTelecommunications Commission (CRTC) regulate the use of mobilecommunications systems

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 30 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan4242011 F-150 (f12)Owners Guide, 2nd PrintingUSA (fus)

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is

GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?This guide describes the scheduled maintenance required for yourvehicle. Carefully following

Note: On models equipped with a 6.2L engine, your message center isNOT equipped with the Intelligent Oil Life Monitor™. Owners of SVTRaptor, Harley-Da

Genuine Ford parts and serviceWhen planning your maintenance services, consider your dealership forall your vehicle’s needs.There are a lot of reasons

Engine oil/coolant change intervalsEngine oil(3.5L/3.7L/5.0L)As indicated by the message center (can beup to one year or 10,000 miles [16,000 km])Engi

SHIFT DELAYED PULL FORWARD (if equipped) — May displaywhen shifting to or from 4X4 LOW. For more information, refer toFour-wheel drive (4WD) operation

Multi-point inspectionIn order to keep your vehicle running right, it is important to have thesystems on your vehicle checked regularly. This can help

Scheduled Maintenance4312011 F-150 (f12)Owners Guide, 2nd PrintingUSA (fus)

NORMAL SCHEDULED MAINTENANCE AND LOG3.5L, 3.7L and 5.0L enginesFor your convenience, your vehicle is equipped with a message centerwhich determines th

3.5L, 3.7L and 5.0L enginesOil Change Service Interval* 1 23456789101112131415Change engine oil and filter • ••••••••••••••Rotate tires, inspect tire

Perform the services noted in the following table at the specifiedtime/mileage (km) period either within 3,000 miles (4,800 km) of theOIL CHANGE REQUI

Every 150,000 miles(240,000 km)Change automatic transmission fluid and filter(except 5–speed TorqShift威 transmission) (filternot required on 6F35, 6F5

6.2L engine (Harley-Davidson™, Lariat Limited and SVT Raptor)Miles (x 1,000)* 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75Kilometers (x 1,000)* 12 24 36 48

6.2L engine (Harley-Davidson™, Lariat Limited and SVT Raptor)Miles (x 1,000)* 82.5 90 97.5 105 112.5 120 127.5 135 142.5 150Kilometers (x 1,000)* 132

Every 15,000 miles(24,000 km)Replace cabin air filter (if equipped)Every 30,000 miles(48,000 km)Replace climate-controlled seat filter (ifequipped)Rep

Maintenance schedule logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDAT

VEHICLE NEAR TOP SPEED — Displayed when a MyKey威 is in useand the MyKey speed limit is on and the vehicle speed is approaching80 mph (130 km/h). Refer

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

SPECIAL OPERATING CONDITIONS - 3.5L, 3.7L AND 5.0L ENGINESIf you operate your vehicle primarily in one of the more demandingconditions listed below, y

Extensive idling and/or low-speed driving for long distances as in heavycommercial use such as delivery, taxi, patrol car or livery - 3.5L, 3.7L and5.

Operating in dusty conditions such as unpaved or dusty roads - 3.5L, 3.7Land 5.0L enginesInspect frequently, service asrequired– Replace cabin air fil

Exclusive use of E85 (Flex Fuel Vehicles only) - 3.5L, 3.7L and 5.0L enginesEvery oil change interval – If ran exclusively on E85, fill the fuel tank

Extensive idling and/or low-speed driving for long distances as in heavycommercial use such as delivery, taxi, patrol car or livery - 6.2L engine(Harl

Operating in dusty conditions such as unpaved or dusty roads - 6.2Lengine (Harley-Davidson™, Lariat Limited and SVT Raptor)Inspect frequently, service

Exclusive use of E85 (Flex Fuel Vehicles only) - 6.2L engine(Harley-Davidson™, Lariat Limited and SVT Raptor)Every oil change interval – If ran exclus

Special operating condition logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER

WIRING FAULT ON TRAILER (if equipped) — Displayed if thereare certain faults in the vehicle wiring and trailer wiring/brake system.Refer to Trailer to

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

EXCEPTIONSIn addition, there are several exceptions to the Normal Schedule. Theyare listed below:Normal vehicle axle maintenance❑Rear axles and power

ENGINE COOLANT CHANGE RECORD3.5L, 3.7L and 5.0L enginesInitial change 6 years or 100,000 miles (160,000 km)(whichever comes first)After initial change

Engine coolant change logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDA

AAccessory delay ...103AdvanceTrac ...280Airbag supplemental restraintsystem ...189–190,

CD ...48Cell phone use ...9Changing a tire ...333Child s

Engine ...415cleaning ...358coolant ...382fail-

Hood ...370IIgnition ...272, 415Illuminated visor mirror ...95Infant seat

OOctane rating ...393–394Oil (see Engine oil) ...376PParental MyKeyprogramming ...133Parking

Safety ComplianceCertification Label ...416Satellite Radio ...48Satellite Radio Information ...62Sched

AUDIO SYSTEMSAM/FM stereo system (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strong

Transmission ...293brake-shift interlock(BSI) ...289, 291fluid, checking and adding(automatic)

2. AUDIO: Press AUDIO repeatedlyto gain access to the followingsettings:BAL (Balance): Press AUDIO to reach the balance setting.Use/ / SEEK to adjust

Setting the clock: Press and hold CLK until the hours begin to flash.Press / / SEEK to manually increase/decrease the hours.Press CLK again to set the

Battery management: When the engine is off, your audio system mayturn off if the battery is at a low state of charge or if the ignition hasbeen in the

Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti

SEEK: Press SEEK to access the previous/next strong radiostation.SCAN: Press for a brief sampling of all strong radio stations.0–9 (MEMORY PRESETS): W

CD/MP3 PlayerCD: Press to enter CD/MP3 mode. If a disc is already loaded into thesystem, CD/MP3 play will begin where it ended last. If no CD is loade

SCAN: Press for a brief sampling of all tracks on the current disc orMP3 folder.DIRECT:In CD mode– Press DIRECT. The display will read DIRECT TRACKMOD

DIRECT: Press DIRECT then enter the desired channel (i.e. 002) usingthe memory preset buttons (0–9). If you only enter one digit, press OKand the syst

SATELLITE RADIO MENU: Press MENU when satellite radio mode isactive to access. Press OK to enter into the satellite radio menu.Press to cycle through

d. DISABLE ALERTS/ENABLE ALERTS: Press OK toenable/disable the satellite alert status which alerts you when yourselected songs are playing on a satell

FADE: Press SEEK to adjust the audio between the back (B)and front (F) speakers.SPEED COMPENSATED VOLUME: With this feature on, radio volumeautomatica

Auxiliary input jack (Line in — if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly

6. Press AUX on the vehicle radio repeatedly until LINE, LINE IN orSYNC LINE IN appears in the display.You should hear audio from your portable music

Your vehicle may be equipped with aUSB port located on the instrumentpanel. This feature allows you toplug in media playing devices,memory sticks, and

Do not add friction modifier compounds or special break-in oils since theseadditives may prevent piston ring seating. See Engine oil in theMaintenance

• Wipe discs from the center out.Don’t:• Expose discs to direct sunlight or heat sources for extended periodsof time.• Clean using a circular motion.C

MP3 track and folder structureYour MP3 system recognizes MP3 individual tracks and folder structureas follows:• There are two different modes for MP3

Satellite radio information (if equipped)Satellite radio channels: SIRIUS威 broadcasts a variety of music, news,sports, weather, traffic and entertainm

Satellite radio electronic serial number (ESN): This 12–digitSatellite Serial Number is needed to activate, modify or track yoursatellite radio accoun

Radio Display Condition Action RequiredNO TEXT Artist information notavailable.Artist information notavailable at this time onthis channel. Thesystem

NAVIGATION SYSTEM (IF EQUIPPED)Your vehicle may be equipped with a navigation system. Refer to theNavigation System supplement for further information

SINGLE ZONE CLIMATE CONTROL1.Defrost: Distributes outside air through the windshield defrostervents and de-mister vents. Can be used to clear the wind

• : Distributes air through the floor vents, demister vents and rearseat floor vents (if equipped).4. A/C: Press to activate/deactivate air conditioni

• Do not put objects under the front seats that will interfere with theairflow to the back seats.• Remove any snow, ice or leaves from the air intake

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS (IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Messag

NOTICE TO OWNERS ABOUT HIGH PERFORMANCE TIRESNote: Your vehicle is equipped with high performance tires. When firstdriving the vehicle after it has be

4. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. A/Cengages automaticall

11. Power/Driver temperature: Press to activate/deactivate theclimate control system. When the system is off, outside air is preventedfrom entering th

2. Defrost: Distributes outside air through the windshield defrostervents and de-mister vents. Can be used to clear the windshield of fogand thin ice.

and when the ignition is cycled (if the A/C indicator light is notilluminated ) in order to prevent window fogging. Even when this buttonis not select

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED AND COOLED SEATS (NAVIGATION BASED–IFEQUIPPED)Temperature conversion: To switch between Fahrenheit

5. Passenger heated seat (if equipped): Press to control thepassenger heated seat. Refer to Heated and cooled seats in the Seatingand Safety Restraint

14. Defrost: Distributes outside air through the windshielddefroster vents and de-mister vents. Can be used to clear the windshieldof fog and thin ice

Max A/C: Distributes recirculated air through the instrument panelvents to cool the vehicle. This re-cooling of the interior air is moreeconomical and

To aid in side window defogging/demisting in cold weather:1. Select .2. Select A/C.3. Adjust the temperature control to maintain comfort.4. Set the fa

Manual climate controlFor hot weather conditions:• The climate control system will be set to MAX A/C.For cold weather conditions:• The climate control

• Where the driver was positioning the steering wheel.This data can help provide a better understanding of thecircumstances in which crashes and injur

HEADLAMP CONTROLRotate the headlamp controlclockwise to the first position toturn on the parking lamps.Rotate clockwise to the secondpositionto also t

High beamsPull the lever fully past the detentto activate. Pull the lever fully againto deactivate.Flash-to-passPull toward you slightly to activatean

PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicablelit components in the vehicle duringheadlamp and parking lam

3. Turn on the low beam headlamps to illuminate the wall or screen andopen the hood. Cover one of the headlamps so no light hits the wall.4. On the wa

• Push the lever up/down to the first stop position and hold. The turnsignals will flash for as long as the lever is held in this position.INTERIOR LA

Rear courtesy/reading/cargo lamps (if equipped)The rear lamps can be turned onwhen the panel dimmer control isrotated until the lamps come on orwhen a

BULB REPLACEMENTLamp assembly condensationExterior lamps are vented to accommodate normal changes in pressure.Condensation can be a natural by-product

Function Number ofbulbsTrade numberHeadlamps 2 H13/9008Front park/turn lamps 2 3157NA (naturalamber)Front sidemarker 2 168Fog lamps 2 9140Backup lamp

3. Loosen the three retaining bolts(two at top of lamp, one at lowerinboard corner).4. Once the three retaining bolts have been removed, slide the hea

Replacing front parking lamp/turn signal/sidemarker bulbs1. Make sure that the headlamp control is in the off position and openthe hood.2. Remove the

reports, or business searches your request. If you do not wantFord or its vendors to receive this information, do not activatethe service. Ford Motor

Replacing tail/brake/turn signal/backup lamp bulbs1. Make sure the headlamp controlis in the off position.2. Open the tailgate to expose thelamp assem

Replacing fog lamp bulbs (if equipped)1. Make sure the headlamp controlis in the off position.2. Remove the bulb socket from thefog lamp by turningcou

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate toward you to decrease thes

Windshield washer: Press the endof the stalk:• briefly: causes a single swipe ofthe wipers without washer fluid.• a quick press and hold: thewipers wi

WARNING: Never adjust the steering column when the vehicleis moving.Power Tilt/Telescope Steering Column (if equipped)The steering column can beadjust

On vehicles with memory feature, to prevent damage to the steeringcolumn, the steering column is designed to set a stopping position justshort of the

CENTER CONSOLE (IF EQUIPPED)Your vehicle may be equipped with a variety of consoles features. Theseinclude:• Locking storage compartmentwith hanging f

Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the on p

2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons.3. Slowly d

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe ba