Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 18Message center 19Entertainment Systems 47AM/FM stereo 47AM/FM stereo with CD/M
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
The power point can switch to a fault mode when it is overloaded,overheated, or shorted. For overloading and shorting conditions, unplugyour device an
Press and pull the window switchesto open and close windows.• Press down (to the first detent)and hold the switch to open.• Pull up (to the first dete
Bounce-back override (front windows only)To override bounce-back, within two seconds after reaching bounce-backposition, if the switch is moved from t
Accessory delay (if equipped)With accessory delay, the window switches may be used for up to10 minutes after the ignition switch is turned to the off
EXTERIOR MIRRORSPower side view mirrors (if equipped)WARNING: Do not adjust the mirror while the vehicle is inmotion.To adjust your mirrors:1. Rotate
Fold-away mirrorsFold the side mirrors in carefullybefore driving through a narrowspace, like an automatic car wash.Powerfold mirrors (if equipped)Wit
On vehicles not equipped with rear defrost, press the heated mirrorcontrol located on the climate control panel. For more informationrefer to the Clim
POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedal should only be adjusted when thevehicle is stopped and the gearshift lever i
Enable/disable:To enable/disable the power running board feature, refer to Messagecenter in the Instrument Cluster chapter.• When this feature is disa
WARNING: Do not use the speed control in heavy traffic or onroads that are winding, slippery or unpaved.Using speed controlsThe speed controls are loc
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
Disengaging speed controlTo disengage speed control, tap the brake pedal or clutch pedal (ifequipped) or press CNCL.Disengaging the speed control will
STEERING WHEEL CONTROLS (IF EQUIPPED)Radio control features– VOL + (Volume): Press todecrease or increase the volume.(Seek): Press to selectthe previo
For further information on the SYNC威 system, refer to the SYNC威supplement.Navigation system/SYNC威hands-free control features (ifequipped)Presscontrol
To open the moon roof: Press andrelease the SLIDE control, the moonroof will open automatically. Pressthe switch again to stop the moonroof.To close t
Car2U姞 Home Automation System (if equipped)The Car2U威 Home AutomationSystem is a universal transmitterlocated in the driver’s visor thatincludes two p
Types of garage door openers (rolling code and fixed code)The Car2U威 Home Automation System may be programmed to operaterolling code and fixed code ga
Note: Do not program the Car2U威 system with the vehicle in the garage.Make sure that your key is on and engine off while programming thetransmitter.1.
4. Press and release the button again. The garage door should move,confirming that programming is successful. If your garage door does notoperate, rep
2. Open the battery cover and record the switch settings from left toright for all 8 to 12 switches. Use the figure below:When a switch is in the up,
5. Press and hold the Car2U威system button you would like to useto control the garage door.Immediately (within 1 second)release the button once the gar
WARNING LIGHTS AND CHIMESBase instrument cluster shown in standard measure; metricsimilar. Uplevel clusters similar.Warning lights and gauges can aler
FCC and RSS-210 Industry Canada ComplianceThe Car2U威 system complies with Part 15 of the FCC rules and withRSS-210 of Industry Canada. Operation is su
Tailgate removalYour tailgate is removable to allow more room for loading.WARNING: Always properly secure cargo to prevent shiftingcargo or cargo fall
Tailgate step (if equipped)Your vehicle may be equipped with a feature that allows easier entry intothe truck bed. To open the tailgate step:1. Flip d
Note:• Fully close and latch the tailgate step before moving the vehicle.• Never drive with the step or grab handle deployed.• Replace slip resistance
To stow the box side step, with your foot, push the box side step underthe truck until fully latched. Do not push on the button while stowingthe box s
2. Open the latches to release thepanels.3. Rotate the panels toward thetailgate.Repeat Steps 1–3 for the other side of the bed extender.4. Connect th
5. Ensure the latch rod is insertedinto the tailgate hole and the lockingpins on both sides are engaged intotheir holes in the pick-up box.6. Reverse
CARGO MANAGEMENT SYSTEM (IF EQUIPPED)The cargo management system consists of the Cargo rail package withthe following as optional accessories:• Front
• To remove cleat from rail, pull the knob and turn slightly to lock openand slide it off the end of the rail.When installing cleat, reverse instructi
Cross bars: Aluminum cross bars with T-slot channels in all four sides,and a latch mechanism that allows the end supports to snap over theexisting cle
Uplevel message centerNote: Some warning lights arereconfigurable telltale (RTT)indicator lights and will illuminate inthe message center. These light
Bed divider: This panel will keep small items up to 400 lb (180 kg) inposition in the pickup box. Also includes T-slots to allow attachment ofindustry
Side mounted tool bins: Watertight bins can be positioned at any pointalong the side rails and can be easily removed (even when full), andcarried to w
• To remove the bin from the rail, open lid and pull up on both leverslocated on the outboard edge (next to the pickup box top rail) untilthe handles
KEYSYour vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and
MyKey™ restricted featuresStandard settings – These settings cannot be changed• The audio system will be muted whenever Belt-Minder威 is activateduntil
4. Wait until KEY RESTRICTED AT NEXT START is displayed.For optional message center:1. At the main menu screen select SETTING then MYKEY by pressingOK
For optional message center:1. At the main menu screen select SETTING then MYKEY by pressingOK or the right arrow key.2. Use the up and down arrows to
Refer to Message center in the Instrument Cluster chapter for MyKey™system warnings displays.Using MyKey™ with remote start systemsMyKey™ is not compa
status menus will include the non Ford-approved remote start system asan additional key in the total count. See the Check MyKey™ systemstatus section.
TroubleshootingCondition Potential CausesCan’t create aMyKey™• Key in the ignition is already a MyKey™.• Key in the ignition is the last remaining adm
“limp-home” operation or when a transmission problem has beendetected and shifting may be restricted. If the light remains on, have thesystem serviced
Condition Potential Causesbutton start Ford-approved remote start system (as an adminkey) then a MyKey™ is inserted without restartingthe engine.MyKey
Smart locks (if equipped)This feature prevents you from locking yourself out of the vehicle if yourkey is still in the ignition.When you open the driv
Power door lock switch autolock enable/disable procedureBefore starting, ensure the ignition is in the off position and all vehicledoors are closed. Y
• the vehicle has then come to a stop and the ignition is turned to theoff ) or accessory position; and• the driver door is opened within 10 minutes o
Keyless entry keypad autounlock enable/disable procedure1. Turn the ignition to the offposition.2. Close all the doors.3. Enter factory–set 5–digit en
REMOTE ENTRY SYSTEM (IF EQUIPPED)The integrated keyhead transmitter (IKT) complies with part 15 of theFCC rules and with RSS-210 of Industry Canada. O
Two step door unlocking1. Press and release to unlock the driver’s door. Note: The parkinglamps and interior lamps will illuminate (refer to the Illum
Sounding a panic alarmPressto activate the alarm. Press again or turn the ignition to on todeactivate.Note: The panic alarm will only operate when the
Replacing the batteryThe integrated keyhead transmitter (IKT) or intelligent access key (IAkey) uses one coin type three-volt lithium battery CR2032 o
Illuminated entryThe interior lamps and parking lamps illuminate when the remote entrysystem is used to unlock the door(s).The illuminated entry syste
Airbag readiness: If this light failsto illuminate when the ignition isturned to on, continues to flash orremains on, have the systemserviced immediat
The remote start system will not work if:• The ignition is in the on position.• The alarm system is triggered.• The feature has been disabled.• The ho
Turning the engine off after using remote start• Pressone time. The parking lamps will turn off.You may have to be closer to the vehicle than when sta
Tips:• Do not set a code that uses five of the same number.• Do not use five numbers in sequential order.• The factory set code will work even if you
SECURILOCK姞 PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED)SecuriLock威 passive anti-theft system is an engine immobilizationsystem. This system is designed to
Programming spare keysA maximum of eight keys can be coded to your vehicle. OnlySecuriLock威 keys can be used. To program a coded key yourself, youwill
6. To program additional new unprogrammed key(s), repeat Steps 1through 5.If successful, the new coded key(s) will start the vehicle’s engine and thet
Disarming the systemYou can disarm the system by any of the following actions:• Unlock the doors by pressing thecontrol on your remote entrytransmitte
FRONT SEATSWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the eve
To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint by pulling up
Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as possible to theba
Low tire pressure warning:Illuminates when your tire pressureis low. If the light remains on atstart up or while driving, the tirepressure should be c
• Pull the release lever handlelocated on the side of the seat upto move the seatback forward orbackward.Using the armrest (if equipped)• Push the rel
• To gain access to the storagecompartment (if equipped) inyour armrest, lift the latch toopen the lid.Using the manual lumbar supportFor more lumbar
Using the power lumbar support (if equipped)The power lumbar control is located on the outboard side of the seat.Press the forward side of the control
The control is located on the outboard side of the seat cushion.Move the switch to raise or lowerthe front or rear portion of the seatcushion.Move the
position using the associated controls. Press and hold button 1 for atleast two seconds. A chime will sound confirming that a memoryposition has been
the vehicle and inserting the key in the ignition while in P (Park), theeasy entry feature will move the seat an additional 2 inches (5 cm) tothe desi
Note: Do not do the following:• Place heavy objects on the seat• Operate the seat heater if water or any other liquid is spilled on theseat. Allow the
To operate the heated seats:Press the heated seat symbol tocycle through the various heatsettings and off. Warmer settings areindicated by more indica
To remove an air filter:1. Turn the vehicle off.2. Push up on the outside rigid edgeof the filter until the tabs arereleased, then rotate the air filt
WARNING: The adjustable head restraint is a safety device.Whenever possible it should be installed and properly adjustedwhen the seat is occupied.The
ignition is turned on, or remains on, have the system servicedimmediately by your authorized dealer.Four-wheel drive high (RTT) (ifequipped): Displays
1. Pull control on the side of the seat to release seat cushion fromstorage position.2. Push seat cushion down until it locks into horizontal position
Armrest and cupholders (if equipped)Pull the strap located on the centerseatback to access the armrest andcupholders.The cupholders are located inside
To operate the heated seats:• Push the indicated side of thecontrol for maximum heat.• Push again to deactivate.• Push the indicated side of thecontro
• Passenger Airbag Off indicator light.• Restraints Control Module (RCM) with impact and safing sensors.• Restraint system warning light and back-up t
Driver’s seat position sensorThe driver’s seat position sensor allows your Personal Safety System totailor the deployment level of the driver dual-sta
airbag is off. See Front passenger sensing system in the Airbagsupplemental restraint system (SRS) section of this chapter.Front safety belt usage sen
If any of these things happen, even intermittently, have the PersonalSafety System serviced at an authorized dealer immediately. Unlessserviced, the s
WARNING: When possible, all children 12 years old and undershould be properly restrained in a rear seating position.WARNING: Safety belts and seats ca
shortened, but pinches the webbing to keep the lap portion from gettinglonger. The cinch tongue is designed to slip during a crash, so alwayswear the
WARNING: Each seating position in your vehicle has a specificsafety belt assembly which is made up of one buckle and onetongue that are designed to be
GAUGESBase cluster with automatic transmission shown; metric similar.Uplevel clusters similar.1. Engine oil pressure gauge: Indicates engine oil press
Safety belt systems equipped with an energy management retractor mustbe replaced if they were in use during a frontal collision which resultedin deplo
How to use the automatic locking mode1. Buckle the combination lap andshoulder belt (front safetybelt/buckle shown, rear similar).2. Grasp the shoulde
Safety belt pretensionerYour vehicle is equipped with safety belt pretensioners at the driver andright front passenger seating positions.The safety be
Front safety belt height adjustmentYour vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shou
Belt-Minder姞The Belt-Minder威 feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders byinterm
If... Then...The driver’s and frontpassenger’s safety belts arebuckled...The Belt-Minder威 feature will notactivate.The driver’s or frontpassenger’s sa
The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate
1. Turn the ignition switch to the on position. DO NOT START THEENGINE.2. Wait until the safety belt warning light turns off. (Approximately oneminute
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The airbag supplemental restraint system is designed to work inconjunction with the safety belts to help pro
slightly when the vehicle is in motion or on a grade. The fuel icon andarrow indicates which side of the vehicle the fuel filler door is located.Refer
Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in
WARNING: Do not attempt to service, repair, or modify theairbag supplemental restraint systems or its fuses. Contact yourauthorized dealer as soon as
If two adults and a child occupy a Regular Cab, properly restrain thechild in the center front unless doing so would interfere with driving thevehicle
internal injuries, particularly to occupants who are not properlyrestrained or are otherwise out of position at the time of airbagdeployment. Thus, it
The front passenger sensing systemuses a ⬙passenger airbag off⬙ or⬙pass airbag off⬙ indicator which willilluminate and stay lit to remind youthat the
• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LampPasseng
ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase,
A difficulty with the system is indicated by one or more of the following:• The readiness lights will eitherflash or stay lit.• The readiness lights w
How does the side airbag system work?The design and development of theside airbag system includedrecommended testing proceduresthat were developed by
WARNING: Several airbag system components get hot afterinflation. Do not touch them after inflation.WARNING: If the sideairbag has deployed, theairbag
Locks and Security 133Keys 133Locks 140Anti-theft system 153Seating and Safety Restraints 157Seating 157Safety restraints 172Airbags 189Child restrain
Info (information menu)Press the INFO button repeatedly tocycle through the following features:TRIP A/BRegisters the distance of individual journeys.
Safety Canopy姞 SystemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a deploying
How does the Safety Canopy姞 System work?The design and development of theSafety Canopy system includedrecommended testing proceduresthat were develope
The Safety Canopy is mounted to roof side-rail sheet metal, behind theheadliner, above each row of seats. The Safety Canopy is designed toinflate betw
• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and/or light are repaired.If any of these things ha
Important child restraint precautionsWARNING: Always make sure your child is secured properly ina device that is appropriate for their height, age and
Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb
Recommendations for attaching child safety restraints for childrenRe-straintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(low
WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli
Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle.If the child is the proper height, age, and weigh
Installing child safety seats with combination lap and shoulderbeltsCheck to make sure the child seat is properly secured before each use.Children 12
• Differences in the automatic shut-off points on the fuel pumps atservice stations• Variations in top-off procedure from one fill-up to another• Roun
If you are using a front center seat, see Installing child safety seats incinch tongue combination lap and shoulder belt seating positionlater in this
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up
1. Position the child safety seat inthe center front seat.2. If the center lap/shoulder safetybelt has been disconnected from theseat to carry large c
5. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
9. Before placing the child into thechild seat, forcibly pull the childseat forward and back to make surethat the seat is held securely inplace. To ch
Your vehicle is equipped with LATCH lower anchors for child seatinstallation at the following seating positions (LATCH is not available onF150 Regular
Use of inboard lower anchors from the outboard seating positions(center seating use)The lower anchors at the center of the second row rear seat are sp
The passenger seats of your vehicle are equipped with built-in tetherstrap anchors located behind the seats as described below.The tether anchors in y
Once the child safety seat has been installed using either the safety belt,the lower anchors of the LATCH system, or both, you can attach the toptethe
System check and vehicle feature customizationPress the SETUP button repeatedlyto cycle the message center throughthe following features:RESET FOR SYS
Rear seat tether strap attachment (SuperCab and SuperCrew)There are three loops of webbingjust above the back of the rear seat(along the bottom edge o
3. Tighten the tether strapaccording to the child seatmanufacturer’s instructions.If the safety seat is not anchored properly, the risk of a child bei
When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the
Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary
• Narrower – to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUVs and
TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen
An oil change is required whenever indicated by the message center andaccording to the recommended maintenance schedule. USE ONLYRECOMMENDED ENGINE OI
Glossary of tire terminology• Tire label: A label showing the OE (Original Equipment) tire sizes,recommended inflation pressure and the maximum weight
INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air
The cold inflation pressure should never be set lower than therecommended pressure on the Safety Compliance Certification Label orTire Label.When weat
TIRE CAREInspecting your tires and wheel valve stemsPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones
WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressur
Tire replacement requirementsYour vehicle is equipped with tires designed to provide a safe ride andhandling capability.WARNING: Only use replacement
Important: Remember to replace the wheel valve stems when the roadtires are replaced on your vehicle.It is recommended that the two front tires or two
you cannot detect a cause, have the vehicle towed to the nearest repairfacility or tire dealer to have the vehicle inspected.Tire and wheel alignmentA
Note: After having your tires rotated, check tire pressure and adjust tothe recommended inflation pressure.Note: The TPMS reset tool is ONLY provided
Note: If your tire size does not begin with a letter this may mean it isdesignated by either ETRTO (European Tire and Rim TechnicalOrganization) or JA
Press the RESET button to turn the easy entry/exit seat on or off.REAR PARK AID (if equipped)This feature sounds a tone to warn the driver of obstacle
Letter rating Speed rating - mph (km/h)M 81 mph (130 km/h)N 87 mph (140 km/h)Q 99 mph (159 km/h)R 106 mph (171 km/h)S 112 mph (180 km/h)T 118 mph (190
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including inter
To restore the full functionality of the tire pressure monitoring system,have the damaged road wheel/tire repaired and remounted on yourvehicle. For a
Low tirepressurewarninglightPossiblecauseCustomer action requiredFlashingwarning lightSpare tirein useYour temporary spare tire is in use. Repairthe d
TPMS reset procedureThe TPMS reset procedure needs to be performed after each tirerotation on vehicles that require different recommended tirepressure
3. Cycle the ignition to the onposition with the engine off.4. Turn the hazard flashers on thenoff three times. This must beaccomplished within 10 sec
• Some messages will appear once and then again when the vehicle isrestarted.• Some messages will reappear after clearing or being reset if a problemo
8. Remove the valve cap from the valve stem on the right rear tire;decrease the air pressure until the horn sounds.9. Remove the valve cap from the va
Follow these guidelines when using snow tires and chains:• If possible, avoid fully loading your vehicle.• Use only SAE Class S chains.• Install chain
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the
to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400
Note: Do not exceed trailer weight of 5,000 lb (2,268 kg) when towingwith bumper only.Exceeding the maximum GCWR could result in extensive damageto yo
LOW BATTERY LESS FEATURES (if equipped) — Displayed whenthe battery management system detects an extended low-voltagecondition. Various vehicle featur
Regular CabEngine Rear axleratioMaximumGCWR - lb (kg)Maximum TrailerWeight - lb (kg)2WD 126” wheelbase3.7L3.55 10400 (4717) 5500 (2495)3.73 10900 (494
SuperCabEngine Rear axleratioMaximumGCWR - lb (kg)Maximum TrailerWeight - lb (kg)2WD 145” wheelbase3.5L 3.15 14000 (6350) 8600 (3901)3.55 15200 (6895)
SuperCrewEngine Rear axleratioMaximumGCWR - lb (kg)Maximum TrailerWeight - lb (kg)2WD 145” wheelbase3.5L 3.15 14000 (6350) 8500 (3856)3.55 15300 (6940
SuperCrewEngine Rear axleratioMaximumGCWR - lb (kg)Maximum TrailerWeight - lb (kg)2WD 157” wheelbase3.5L3.15 14000 (6350) 8400 (3810)3.55 15300 (6940)
Weight-distributing hitchWhen hooking-up a trailer using a weight-distributing hitch, always usethe following procedure:1. Park the vehicle (without t
WARNING: Do not connect a trailer’s hydraulic brake systemdirectly to your vehicle’s brake system. Your vehicle may nothave enough braking power and y
manual activation without a trailer connected or when gainadjustments are made with no trailer connected.• TBC GAIN = XX.X OUTPUT = //////: When the v
1. Make sure the trailer brakes are in good working condition,functioning normally and properly adjusted. See your trailer dealer ifnecessary.2. Hook
Points to Remember:• Remember to adjust gain setting before using the TBC for the firsttime.• Readjust gain setting on the TBC (according to procedure
Using a step bumper (if equipped)The rear bumper is equipped with an integral hitch and only requires aball with a one inch (25.4 mm) shank diameter.
TIRE PRESSURE MONITOR FAULT — Displayed when the tirepressure monitoring system (TPMS) is malfunctioning. If the warningstays on or continues to come
refilling your rear axle with synthetic gear lube if not already soequipped. Refer to the Maintenance and Specifications chapter forthe lubricant spec
as vehicle or transmission damage may occur. It is recommended to towyour vehicle with all four (4) wheels off the ground such as when using acar-haul
STARTINGPositions of the ignition1. Off — locks the automatictransmission gearshift lever andallows key removal. Note: In orderto switch off the engin
WARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine compartment and exhaus
3. Make sure the gearshift is in P(Park).4. Make sure the parking brake isset.5. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warni
Starting the engine1. Turn the key to 3 (on) withoutturning the key to 4 (start).2. Turn the key to 4 (start), thenrelease the key as soon as theengin
If you should experience cold weather starting problems on E85ethanol,and neither an alternative brand of E85ethanol nor an engine blockheater is avai
WARNING: Failure to follow engine block heater instructionscould result in property damage or physical injury.WARNING: To reduce the risk of electrica
• Finally, have the engine block heater system checked during your falltune-up to be sure it’s in good working order.How to use the engine block heate
Using ABSWhen hard braking is required, apply continuous force on the brakepedal. Do not pump the brake pedal since this will reduce theeffectiveness
SHIFT DELAYED PULL FORWARD (if equipped) — May displaywhen shifting to or from 4X4 LOW. For more information, refer toFour-wheel drive (4WD) operation
WARNING: Always set the parking brake fully and make surethat the gearshift is securely latched in P (Park) (automatictransmission) or in 1 (First) (m
WARNING: Remember that even advanced technology cannotdefy the laws of physics. It’s always possible to lose control of avehicle due to inappropriate
When AdvanceTrac威 with RSC威 performs a normal system self-check,some drivers may notice a slight movement of the brake, and/or arumble, grunting, or g
Electronic stability control (ESC)Electronic stability control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa
Switching off AdvanceTrac威 with RSC威If the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off certain features of the
AdvanceTrac威 with RSC威 FeaturesButton functionsStabilitycontrolOFF lightRSC威 ESC TCSButton pressedagain afterdeactivationNotilluminatedEnabled Enabled
speed at which trailer sway will not grow continuously. This may causethe system to activate multiple times, causing a gradual reduction inspeed.Note:
WARNING: The EPS system has diagnostics checks thatcontinuously monitor the EPS system to ensure proper operationof the electronic system. When an ele
All enginesIf the steering wanders or pulls equipped with either an EPS or ahydraulic steering system, check for:• an improperly inflated tire• uneven
Utility vehicles and trucks have larger tires and increased groundclearance, giving the vehicle a higher center of gravity than a passengercar.WARNING
VEHICLE NEAR TOP SPEED — Displayed when a MyKey™ is in useand the MyKey speed limit is on and the vehicle speed is approaching80 mph (130 km/h). Refer
2. Move the shift lever boot bypressing on the edges and moving itup the gearshift lever.3. Turn the steering wheel one-halfturn to access the slots o
5. With the ignition in the onposition, pull back on the BSIsolenoid found on top of theuncovered steering column and atthe same time, apply the brake
If the fuse is not blown and the brake lamps are working properly, thefollowing procedure will allow you to move the gearshift lever from P(Park):1. A
AUTOMATIC TRANSMISSION OPERATIONUnderstanding the shift positions of the 6-speed automatictransmissionThis vehicle is equipped with an adaptive transm
D (Drive) with Tow/Haul OffThe normal driving position for the best fuel economy. Transmissionoperates in gears one through six.D (Drive) with Tow/Hau
To deactivate the tow/haul feature and return to normal driving mode,press the button on the end of the gearshift lever. The TOW HAUL lightwill no lon
PRS (Progressive RangeSelection)With the gearshift lever in D(Drive), press the – button to activePRS. The available and selectedgears will be indicat
Recommended shift speedsUpshift according to the following chart:Upshifts when acceleratingShift from:1 – 2 15 mph (24 km/h)2 – 3 25 mph (40 km/h)3 –
REVERSE SENSING SYSTEM (IF EQUIPPED)The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when R (Reverse
The RSS detects obstacles up to6 feet (2 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the fi
Customer Assistance 347Reporting safety defects (U.S. only) 354Reporting safety defects (Canada only) 354Cleaning 355Maintenance and Specifications 36
HILL CNTRL OFF SYSTEM COOLING (if equipped) — Displayedwhen a hill descent system fault is present.FOR OFF ROAD SLOW TO 5 MPH (if equipped) — Displaye
Keep the RSS sensors (located on the rear bumper/fascia) freefrom snow, ice and large accumulations of dirt (do not clean thesensors with sharp object
Visual park aid alert (if equipped)Visual park aid alert allows the driver to see the area that is causing thereverse sensing system to beep. The visu
When towing, the reverse camera system will only see what is beingtowed behind the vehicle. This might not provide adequate coverage as itusually prov
Press and on the steeringwheel controls to select a zoomoption. You can choose from OFF,Level 1, Level 2 and Level 3. Usethe OK button to make a selec
The camera lens for the reverse camera system is located on the tailgate.Keep the lens clean so the video image remains clear and undistorted.Clean th
• If the image is not clear, then check if there is anything covering thelens such as dirt, mud, ice, snow, etc. If the image is still not clearafter
FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED)WARNING: For important information regarding safe operationof this type of vehicle, see Preparing to dri
• CHECK 4X4 - Displays when a4X4 fault is present.Note: When a 4X4 system fault is present, the system will typicallyremain in whichever 4X4 mode was
Shifting to/from 4L (4X4 low)1. Bring the vehicle to a speed of 3 mph (5 km/h) or less.2. Place the transmission in N (Neutral).3. Move the transfer c
Using the electronic shift 4WD system (if equipped)2H (2WD) - For general on-roaddriving. Sends power to the rearwheels only and should be used forstr
Press the up/down buttons to moveup/down through the messagecenter choices.Press the left/right buttons to moveleft/right through the messagecenter ch
Shifting to/from 4L (4X4 low)1. Bring the vehicle to a speed of 3 mph (5 km/h) or less.2. Place the transmission in N (Neutral).3. Move the 4WD contro
Note: Do not use 4H (4X4 high) on dry, hard surfaced roads. Doing sowill produce excessive noise, increased tire wear and may damage drivecomponents.
The ELD is designed for off-road use only and is not intended for use ondry pavement.Activating the electronic locking differential (ELD)The ELD can b
For vehicles equipped with a 3.5L Ecoboost™ engine:Your vehicle is equipped with an underbody transmission shield andbrackets that may become damaged
• It may be safer to stay on the apron or shoulder of the road and slowdown gradually before returning to the pavement. You may losecontrol if you do
called for. Avoid abrupt steering, acceleration or braking which couldresult in an increased risk of loss of vehicle control, vehicle rolloverand/or p
Power is supplied to all four wheels through a transfer case. On 4WDvehicles, the transfer case allows you to select 4WD when necessary.Information on
If the transmission, transfer case or front axle are submerged in water,their fluids should be checked and changed, if necessary.Driving through deep
Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;
WARNING: If you are driving in slippery conditions that requiretire chains or cables, then it is critical that you drive cautiously.Keep speeds down,
Gauge ModeGauge Detail: In this mode, the following options are available indifferent graphical formats:• Transmission temperature.• Blank screen.Trip
DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
Canadian customers refer to your Warranty Guide or visit ourwebsite at www.ford.ca for information on:Using roadside assistanceComplete the roadside a
FUEL PUMP SHUT-OFFIn the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fue
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
To reinstall the fuse box cover, place the top part of the cover on thefuse panel, then push the bottom part of the cover until you hear it clickshut.
Fuse/RelayLocationFuse AmpRatingProtected Circuits9 10A Radio display, GPS module, Navigationdisplay10 10A Run/accessory relay11 10A Instrument cluste
Fuse/RelayLocationFuse AmpRatingProtected Circuits34 10A Reverse sensing system, 4x4 switch,Rear video, Off road indicator (SVTRaptor)35 5A Hill desce
If the battery has been disconnected and reconnected, refer to theBattery section of the Maintenance and Specifications chapter.The high-current fuses
Fuse/RelayLocationFuse AmpRatingProtected Circuits14 30A** Passenger power seat1540A** Electric fan50A** Electric fan (6.2L with max trailertow, SVT R
• Rounding of the displayed values to the nearest 0.1 gallon (liter).To determine your average highway fuel economy, do the following:1. Drive the veh
Fuse/RelayLocationFuse AmpRatingProtected Circuits39 — TT back-up lamps relay40 — Electric fan relay41 — Not used42 5A* Run/start coil43 15A* TT back-
Fuse/RelayLocationFuse AmpRatingProtected Circuits65 20A** Auxiliary power point (instrumentpanel)66 20A** Auxiliary power point (inside centerconsole
Fuse/RelayLocationFuse AmpRatingProtected Circuits82 — Not used83 — Not used84 — Not used85 — Electric fan relay (low speed)*Mini fuse **Cartridge fus
Note: If your vehicle is equipped with the tire pressure monitoringsystem (TPMS), the indicator light will illuminate when the spare tire isin use. To
When driving with one of the dissimilar spare tires listed above, do not:• Exceed 50 mph (80 km/h)• Load the vehicle beyond maximum vehicle load ratin
• Load leveling adjustment (if applicable)When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to:• Towing a
To remove the jack on SuperCrew models:1. Lift both rear seat cushions.2. Remove the insert containing the Easy Fuel ™ funnel from the driver’sside.3.
WARNING: Do not attempt to change a tire on the side of thevehicle close to moving traffic. Pull far enough off the road toavoid the danger of being h
• FrontNote: Use the frame rail as the jacking location point, NOT the controlarm.Note: For F-150 SVT Raptor, you must always use the jack saddleexten
6. Remove the lug nuts with the lug wrench.7. Replace the flat tire with the spare tire, making sure the valve stem isfacing outward. Reinstall the lu
Truck Apps (if equipped)In this mode, off-road and trailer towing application options are available.*Off RoadPitch and bank angle (in degrees): Displa
3. Turn the jack handle clockwise until the tire is raised to its stowedposition underneath the vehicle. The effort to turn the jack handleincreases s
Note: Inspect the wheel pilot holeprior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean r
Preparing your vehicleWhen the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a
1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery.2. Connect the other end of thepositive (+) cable to the
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.Note: In the illustration, the vehicle on the bottom i
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
Emergency towingIn case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport veh
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehi
In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph
In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext
When “Press OK for options” is displayed, pressing OK will open thetrailer options menus:TrailerChange ActiveTrailerWhen this is highlighted, press th
You are required to submit your warranty dispute to BBB AUTO LINEbefore asserting in court any rights or remedies conferred by CaliforniaCivil Code Se
You can get more information by calling BBB AUTO LINE at1-800-955-5100, or writing to:BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia
GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.
If your vehicle must be serviced while you are traveling or living in theMiddle East, contact the nearest authorized dealer. If the authorizeddealer c
Obtaining a French Owner’s GuideFrench Owner’s Guides can be obtained from your authorized dealer orby contacting Helm, Incorporated using the contact
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i
• Never use abrasive materials such as steel wool or plastic padsas they can scratch the chrome surface.WAXING• Wash the vehicle first.• Use a quality
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
3.7L engineCleaning3582011 F-150 (f12)Owners Guide, 1st PrintingUSA (fus)
5.0L engineCleaning3592011 F-150 (f12)Owners Guide, 1st PrintingUSA (fus)
TrailerRename Trailer Press the right arrow button when this is highlightedto display saved or default trailers. Use the up/downbuttons to highlight a
6.2L engineCleaning3602011 F-150 (f12)Owners Guide, 1st PrintingUSA (fus)
3.5L Ecoboost™ enginePLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your auth
• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft威 Premium Windshield Washer Concentrate (ZC-32-A) inthe U.S., or Premiu
For removal of fine scuffs and scratches, use Scotch-Brite威 MicrofiberCloth or cheese cloth along with Motorcraft Premium Liquid Wax(ZC-53-A), Motorcr
If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows:1. Wipe up spilled liqui
LEATHER SEATS(IF EQUIPPED, EXCEPT FOR THE KING RANCH姞 EDITION)For King Ranch威 leather seats, refer to a separate section in thischapter.• Clean spills
ScratchesNatural Markings - Because the leather in the seat comes from genuinesteer hides, there will be evidence of naturally occurring markings, suc
FORD AND LINCOLN CAR CARE PRODUCTSYour Ford or Lincoln authorized dealer has many quality productsavailable to clean your vehicle and protect its fini
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel.2. Go to the front of the vehicle a
VehicleAutolamp Delay Off or XXX secondsDTE Calculation(distance toempty)Normal History UsedTowing History UsedEasy Entry/Exit On/OffLocks Autolock, O
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.7L V6 engine1. Windshield washer fluid reservoir2. Battery3. Engine oil dipstick (out of view)4. Bra
5.0L V8 engine1. Windshield washer fluid reservoir2. Battery3. Engine oil filler cap4. Engine oil dipstick5. Brake fluid reservoir6. Engine coolant re
6.2L V8 engine1. Windshield washer fluid reservoir2. Engine oil dipstick3. Brake fluid reservoir4. Engine coolant reservoir5. Air filter assembly6. Po
3.5L V6 EcoBoost™ engine1. Windshield washer fluid reservoir2. Battery3. Engine oil filler cap4. Engine oil dipstick5. Brake fluid reservoir6. Engine
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice
2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler cap
Change your engine oil according to the appropriate schedule listed inthe scheduled maintenance information.Ford production and Motorcraft威 replacemen
It is recommended you use the appropriate Motorcraft威 oil filter oranother with equivalent performance for your engine application.BATTERYYour vehicle
WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work
MyKeyCreate MyKey Hold OK to create MyKey*AdvanceTrac Always on or Selectable*MAX Speed 80 MPH (120 km/h) or Off*Speed Warning 45, 55 or 65 MPH (75, 9
If the battery has been disconnected or a new battery has been installed,the clock and radio settings must be reset once the battery isreconnected.• A
ENGINE COOLANTChecking engine coolantThe concentration and level of engine coolant should be checked at theintervals listed in scheduled maintenance i
Note: Automotive fluids are not interchangeable; do not use enginecoolant/antifreeze or windshield washer fluid outside of its specifiedfunction and v
For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when
If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your coolin
concentrations below 40% will decrease the corrosion/freezeprotection characteristics of the engine coolant and may causeengine damage.• If available,
When fail-safe mode is activatedYou have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be ab
You may notice a reduction in the vehicle’s speed caused by reducedengine power. Your vehicle has been designed to enter this mode ifcertain high temp
FUEL FILTERYour vehicle is equipped with a lifetime fuel filter that is integrated withthe fuel tank. Regular maintenance or replacement is not needed
• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek med
System CheckOil LifeDoorsBrakesTire PressureTrailer BrakeCtrl.Gain and Output (when trailer is connected)No trailer (when no trailer is connected)Trai
WARNING: Flexible fuel components and standard unleadedgasoline fuel components are not interchangeable. If your vehicleis not serviced in accordance
• DO NOT use a device that would hold the fuel pump handle in the fillposition.Easy Fuel™ “no cap” fuel systemYour fuel tank is equipped with an Easy
WARNING: The fuel system may be under pressure. If you heara hissing sound near the fuel filler door (Easy Fuel™ “no cap”fuel system), do not refuel u
Some stations offer fuels posted as⬙Regular⬙ with an octane ratingbelow 87, particularly in highaltitude areas. Fuels with octanelevels below 87 are n
Do not add aftermarket fuel additive products to your fuel tank. Itshould not be necessary to add any aftermarket products to your fueltank if you con
Refilling with a portable fuel containerWith the Easy Fuel™ “no cap” fuel system, use the following directionswhen filling from a portable fuel contai
ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform
Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers).2. Each time you fill the tan
• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between the top gears occurs. Unnecessaryshifting of this type co
• Close windows for high speed driving.EMISSION CONTROL SYSTEMYour vehicle is equipped with various emission control components and acatalytic convert
CONGRATULATIONSCongratulations on acquiring your new Ford Motor Company product.Please take the time to get well acquainted with your vehicle by readi
• Some messages can be acknowledged and reset by pressing OK. Thisallows you to use the full message center functionality by clearing themessage.DOOR
Do not make any unauthorized changes to your vehicle or engine. Bylaw, vehicle owners and anyone who manufactures, repairs, services,sells, leases, tr
Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect
POWER STEERING FLUID (6.2L V8 ENGINE ONLY)Check the power steering fluid. Refer to scheduled maintenanceinformation.1. Start the engine and let it run
TRANSMISSION FLUIDChecking 6-speed automatic transmission fluidThe automatic transmission does not have a transmission fluid dipstick.Refer to your sc
AIR FILTERRefer to scheduled maintenance information for the appropriateintervals for changing the air filter element.When changing the air filter ele
3. Clean the area around the airtube to air cover connection toprevent debris from entering thesystem and then loosen the bolt onthe air tube clamp so
8. Replace the air filter housingcover and secure the clamps. Becareful not to crimp the filterelement edges between the air filterhousing and cover a
VEHICLE STORAGEIf you plan on storing your vehicle for an extended period of time(30 days or more), refer to the following maintenance recommendations
Note: During extended periods of vehicle storage (30 days or more),fuel may deteriorate due to oxidation. Add Motorcraft威 Gas Stabilizer orequivalent
• Check the exhaust for any foreign material that may have collectedduring storage.• Check tire pressures and set tire inflation per the Tire Label.•
BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is lowand the brake system should be inspected immediately. Refer to Brakefluid in the Mainten
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord part name orequivalentFord part number /Ford specificationBrake fluidBetweenMIN/MAX
Item CapacityFord part name orequivalentFord part number /Ford specification3.7L enginecoolant16.0 quarts(15.1L)•Motorcraft威 Specialty OrangeEngine Co
Item CapacityFord part name orequivalentFord part number /Ford specificationPower steeringfluid(6.2L engineonly)Fill to betweenMIN and MAXlines on res
Item CapacityFord part name orequivalentFord part number /Ford specificationWindshieldwasher fluidFill as requiredMotorcraft威 PremiumWindshield Washer
Item CapacityFord part name orequivalentFord part number /Ford specificationFuel tankReg. Cab 8’ box /SuperCab 6.5’box /SuperCab 8’ box26.0 gallons(98
ENGINE DATAEngine3.7L V6Engine5.0L V8Engine6.2L V8Engine3.5L V6EcoBoost™EngineCubic inches 226 302 378 214FuelMinimum87 octaneor E85Minimum87 octaneor
6.2L engine3.5L EcoBoost™ engineIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulat
Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX
TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis
FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C
TIRES NOT TRAINED - REPEAT — Displayed when an error occurswhile training the TPMS. Refer to TPMS reset procedure in the Tires,Wheels and Loading chap
Lifestyle•Ash cup / smoker’s package •Racks and carriers*•Bedliners and bedmats •Truck bed camping tent*•Bed side step •Sportliner cargo liner*•Towing
• The Federal Communications Commission (FCC) and Canadian RadioTelecommunications Commission (CRTC) regulate the use of mobilecommunications systems
FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 30 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the
Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With
Ford Extended Service Plan4242011 F-150 (f12)Owners Guide, 1st PrintingUSA (fus)
FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is
GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?This guide describes the scheduled maintenance required for yourvehicle. Carefully following
Note: On models equipped with a 6.2L engine, your message center isNOT equipped with the Intelligent Oil Life Monitor™. Owners of SVTRaptor, Harley-Da
Oils, fluids and flushingIn many cases, fluid discoloration is a normal operating characteristicand, by itself, does not necessarily indicate a concer
Value shopping for your vehicle’s maintenance needsYour dealership recognizes the competitive landscape of maintenance andlight repair automotive serv
FOR 4X4 LOW APPLY BRAKE (if equipped) — Displayed whentrying to select 4X4 LOW. For more information, refer to Four-wheeldrive (4WD) operation in the
Check every monthEngine oil levelFunction of all interior and exterior lightsTires for wear and proper pressure, including spareWindshield washer flui
Multi-point inspection – Recommended each visitAccessory drive belt(s) Half-shaft dust boots (if equipped)Battery performance Horn operationClutch ope
Scheduled Maintenance Guide4322011 F-150 (f12)Owners Guide, 1st PrintingUSA (fus)
NORMAL SCHEDULED MAINTENANCE AND LOG3.5L, 3.7L and 5.0L enginesFor your convenience, your vehicle is equipped with a message centerwhich determines th
3.5L, 3.7L and 5.0L enginesOil Change Service Interval* 1 23456789101112131415Change engine oil and filter • ••••••••••••••Rotate tires, inspect tire
Perform the services noted in the following table at the specifiedtime/mileage (km) period either within 3,000 miles (4,800 km) of theOIL CHANGE REQUI
Every 150,000 miles(240,000 km)Change automatic transmission fluid and filter(except 5–speed TorqShift威 transmission) (filternot required on 6F35, 6F5
6.2L engine (Harley-Davidson™, Lariat Limited and SVT Raptor)Miles (x 1,000)* 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75Kilometers (x 1,000)* 12 24 36 48
6.2L engine (Harley-Davidson™, Lariat Limited and SVT Raptor)Miles (x 1,000)*82.5 90 97.5 105 112.5 120 127.5 135 142.5 150Kilometers (x 1,000)* 132 1
Every 15,000 miles(24,000 km)Replace cabin air filter (if equipped)Every 30,000 miles(48,000 km)Replace climate-controlled seat filter(if equipped)Rep
MYKEY COULD NOT PROGRAM — Displayed when an attempt ismade to program a spare key using two existing MyKeys. Refer toMyKey™ in the Locks and Security
Maintenance schedule logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDAT
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
SPECIAL OPERATING CONDITIONS - 3.5L, 3.7L AND 5.0L ENGINESIf you operate your vehicle primarily in one of the more demandingconditions listed below, y
Extensive idling and/or low-speed driving for long distances as in heavycommercial use such as delivery, taxi, patrol car or livery - 3.5L, 3.7L and5.
Operating in dusty conditions such as unpaved or dusty roads - 3.5L, 3.7Land 5.0L enginesInspect frequently, service asrequired– Replace cabin air fil
Exclusive use of E85 (Flex Fuel Vehicles only) - 3.5L, 3.7L and 5.0L enginesEvery oil change interval – If ran exclusively on E85, fill the fuel tank
Extensive idling and/or low-speed driving for long distances as in heavycommercial use such as delivery, taxi, patrol car or livery - 6.2L engine(Harl
Operating in dusty conditions such as unpaved or dusty roads - 6.2Lengine (Harley-Davidson™, Lariat Limited and SVT Raptor)Inspect frequently, service
Exclusive use of E85 (Flex Fuel Vehicles only) - 6.2L engine(Harley-Davidson™, Lariat Limited and SVT Raptor)Every oil change interval – If ran exclus
TRAILER BRAKE MODULE FAULT (if equipped) — Displayed andaccompanied by a single chime, in response to faults sensed by the TBC.Refer to Trailer towing
Special operating condition logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
EXCEPTIONSIn addition, there are several exceptions to the Normal Schedule. Theyare listed below:Normal vehicle axle maintenance❑Rear axles and power
ENGINE COOLANT CHANGE RECORD3.5L, 3.7L and 5.0L enginesInitial change 6 years or 100,000 miles (160,000 km)(whichever comes first)After initial change
Engine coolant change logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDA
AAccessory delay ...103AdvanceTrac ...280Airbag supplemental restraintsystem ...189–190,
CCapacities for refilling fluids ...410Car2U威 Home AutomationSystem ...114Cargo management system ...127CD ...
EElectronic message center ...19, 30Emergencies, roadsidejump-starting ...341running out of fuel ...341, 394Emission cont
flash to pass ...81high beam ...81replacing bulbs ...87turning on and o
signal ...106Moon roof ...112Motorcraft威 parts ...367, 409MyKey ...
FOR HILL DESCENT SELECT GEAR (if equipped) — Displayedwhen the driver is able to select a transmission gear for hill descentmode.HILL DESCENT - DRIVER
Belt-Minder威,deactivating/activating ...187extension assembly ...188for adults ...177, 179–180for children ...
snow tires and chains ...250spare tire ...333terminology ...230tire grades ...
AUDIO SYSTEMSAM/FM stereo system (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strong
2. AUDIO: Press AUDIO repeatedlyto gain access to the followingsettings:BAL (Balance): Press AUDIO to reach the balance setting.Use/ / SEEK to adjust
7. CLK (Clock): Press CLK totoggle between displaying the radiofrequency and the clock setting.Setting the clock: Press and holdCLK until the hours be
Protecting the environmentWe must all play our part inprotecting the environment. Correctvehicle usage and the authorizeddisposal of waste, cleaning a
Accessory delay: Your vehicle is equipped with accessory delay. Withthis feature, the radio and other electrical accessories may be used forup to ten
SEEK: Press SEEK to access the previous/next strong radiostation.SCAN: Press for a brief sampling of all strong radio stations.0–9 (MEMORY PRESETS): W
CD/MP3 PlayerCD: Press to enter CD/MP3 mode. If a disc is already loaded into thesystem, CD/MP3 play will begin where it ended last. If no CD is loade
SCAN: Press for a brief sampling of all tracks on the current disc orMP3 folder.DIRECT:In CD mode– Press DIRECT. The display will read DIRECT TRACKMOD
cancel your entry by pressing DIRECT. If an invalid station number isentered, INVALID CHANNEL will appear in the display and the systemwill continue p
display. After a category is selected, press SEEK to search forthat specific category of channels only (i.e. ROCK). You may alsoselect CATEGORY ALL to
• CHANNEL LOCKOUT MENU- Press OK to enter the ChannelLockout menu. Press the to scroll through the followingoptions:a. LOCK/UNLOCK THIS CHANNEL: Press
Use SEEK to adjust between SPEED OFF and levels 1–7:Increasing the level from 1 (lowest setting) to 7 (highest setting) allowsthe radio volume to auto
The Auxiliary Input Jack provides away to connect your portable musicplayer to the in-vehicle audiosystem. This allows the audio from aportable music
2. Do not set the portable music player’s volume level higher than isnecessary to match the volume of the CD or FM radio in your audiosystem as this w
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.WARNING: Please read the section Airbag Supple
GENERAL AUDIO INFORMATIONRadio frequencies:AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio
CD units are designed to play commercially pressed 4.75 in(12 cm) audio compact discs only. Due to technicalincompatibility, certain recordable and re
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m
Radio Display Condition Action RequiredNO TEXT Category informationnot available.Category informationnot available at thistime on this channel.The sys
SINGLE ZONE CLIMATE CONTROL1.Defrost: Distributes outside air through the windshield defrostervents and de-mister vents. Can be used to clear the wind
• : Distributes air through the floor vents, demister vents and rearseat floor vents (if equipped).4. A/C: Press to activate/deactivate air conditioni
• Do not put objects under the front seats that will interfere with theairflow to the back seats.• Remove any snow, ice or leaves from the air intake
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS (IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Messag
DATA RECORDINGService Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehi
4. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. A/Cengages automaticall
11. Power/Driver temperature: Press to activate/deactivate theclimate control system. When the system is off, outside air is preventedfrom entering th
2. Defrost: Distributes outside air through the windshield defrostervents and de-mister vents. Can be used to clear the windshield of fogand thin ice.
the ignition is cycled (if the A/C indicator light is not illuminated ) inorder to prevent window fogging. Even when this button is not selected,air m
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED AND COOLED SEATS (NAVIGATION BASED–IFEQUIPPED)Temperature conversion: To switch between Fahrenheit
4. Passenger temperature: Press to activate separate passengertemperature control to increase/decrease the air temperature on thepassenger side of the
12. Driver cooled seat (if equipped): Press to control the drivercooled seat. Refer to Heated and cooled seats in the Seating andSafety Restraints cha
• : Distributes air through the windshield defroster vents, de-mistervents, floor vents and rear seat floor vents. The system willautomatically provid
For maximum cooling performance (MAX A/C):1. Press MAX A/C. The system will default to single zone operation andset the temperature to 60°F (16°C). Th
Manual climate controlFor hot weather conditions:• The climate control system will be set to MAX A/C.For cold weather conditions:• The climate control
limitations regarding 911 Assist and Traffic, directions andInformation privacy below). However, parties, such as lawenforcement, could combine the ED
HEADLAMP CONTROLRotate the headlamp controlclockwise to the first position toturn on the parking lamps.Rotate clockwise to the secondpositionto also t
High beamsPull the lever fully past the detentto activate. Pull the lever fully againto deactivate.Flash-to-passPull toward you slightly to activatean
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicablelit components in the vehicle duringheadlamp and parking lam
3. Turn on the low beam headlamps to illuminate the wall or screen andopen the hood. Cover one of the headlamps so no light hits the wall.4. On the wa
• Push the lever up/down to the first stop position and hold. The turnsignals will flash for as long as the lever is held in this position.INTERIOR LA
Rear courtesy/reading/cargo lamps (if equipped)The rear lamps can be turned onwhen the panel dimmer control isrotated until the lamps come on orwhen a
BULB REPLACEMENTLamp assembly condensationExterior lamps are vented to accommodate normal changes in pressure.Condensation can be a natural by-product
Function Number ofbulbsTrade numberRearstop/turn/sidemarker/taillamp (styleside)4 3057KHigh-mount brakelamp 1 912Cargo lamp 2 912License plate lamp 2
3. Loosen the three retaining bolts(two at top of lamp, one at lowerinboard corner).4. Once the three retaining bolts have been removed, slide the hea
Replacing front parking lamp/turn signal/sidemarker bulbs1. Make sure that the headlamp control is in the off position and openthe hood.2. Remove the
CELL PHONE USEThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri
3. Carefully pull the lamp assemblystraight rearward from the tailgatepillar to disengage two hiddensnap-in retainers. (Flare side taillamps are not e
Replacing license plate lamp bulbsThe license plate bulbs are locatedbehind the rear bumper. To changethe license plate lamp bulbs:1. Reach behind the
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate toward you to decrease thes
Windshield washer: Press the endof the stalk:• briefly: causes a single swipe ofthe wipers without washer fluid.• a quick press and hold: thewipers wi
WARNING: Never adjust the steering column when the vehicleis moving.Power Tilt/Telescope Steering Column (if equipped)The steering column can beadjust
On vehicles with memory feature, to prevent damage to the steeringcolumn, the steering column is designed to set a stopping position justshort of the
CENTER CONSOLE (IF EQUIPPED)Your vehicle may be equipped with a variety of consoles features. Theseinclude:• Locking storage compartmentwith hanging f
Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the on p
2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons.3. Slowly d
To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe ba
Commentaires sur ces manuels