Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Message center 19Entertainment Systems 30AM/FM stereo with CD/MP3 30Auxiliary
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
HomeLink威Car2U威 Home AutomationSystemHomeLink姞 Wireless Control System (if equipped)The HomeLink威 Wireless ControlSystem, located on the driver’s viso
Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink威 equipped vehiclepurchase). I
5. Firmly press and release the “learn” or “smart” button. (The name andcolor of the button may vary by manufacturer.)Note: There are 30 seconds in wh
Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet
Car2U姞 Home Automation System (if equipped)The Car2U威 Home AutomationSystem is a universal transmitterlocated in the driver’s visor thatincludes two p
• Fixed code garage door openers were produced prior to 1996. Fixedcode uses the same coded signal every time. It is manuallyprogrammed by setting DIP
2. Go to the garage to locate thegarage door opener motor and its“learn” button. You may need aladder to reach the unit and youmay need to remove the
Note: The Car2U威 system allows for three devices to be programmed. Ifyou need to change or replace any of the three devices after it has beeninitially
3. To input these positions into theCar2U威 system, simultaneouslypress all three Car2U威 systembuttons for a few seconds and thenrelease to put the dev
Erasing the Car2U姞 Home Automation System buttonsNote: The system allows for three devices to be programmed. If youneed to change or replace any of th
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
INTERIOR TRUNK CONTROLThe trunk release button is locatedon the instrument panel near theradio. Press the button to open thetrunk.CARGO AREA FEATURESC
KEYSIntegrated Keyhead Transmitters (IKTs) (If equipped)Your vehicle may be equipped withtwo Integrated KeyheadTransmitters (IKTs). The key bladefunct
Intelligent Access Key (IA key) (if equipped)Your vehicle may be equipped withtwo Intelligent Access keys whichoperate the power locks and theremote e
MYKEY™The MyKey™ feature allows you to program a restricted driving mode topromote good driving habits. All but one of the keys programmed to thevehic
Create a MyKey™To program MyKey™ on one of the keys programmed to the vehicle,insert the key that you want to make a MyKey™ into the ignition. (Forveh
5. Press SETUP to enter your choice. The next optional setting will bedisplayed.6. Repeat steps 4 and 5 until you are done changing the optionalsettin
Vehicles equipped with traditional keys:When using a Ford-approved remote start system, the default settingswill recognize the remote start system as
TroubleshootingCondition Potential CausesCan’t create a MyKey™ • Key in the ignition is already aMyKey™.• Key in the ignition is the lastremaining Adm
Condition Potential CausesLost any key • For programming spare keys, refer tothe Programming spare keys section inthis chapter.I accidentally programm
POWER DOOR LOCKS• Press thecontrol to unlock alldoors.• Press thecontrol to lock alldoors.Smart unlocksThis feature helps to prevent you from locking
WARNING LIGHTS AND CHIMESStandard instrument cluster shown, optional cluster similarWarning lights and gauges can alert you to a vehicle condition tha
automatically be released when you attempt to close it, and the horn willchirp, as a reminder that the IA key is inside. If you would like tointention
Note: The autolock feature can be activated/deactivated independentlyof the autounlock feature.Power door lock switch autolock enable/disable procedur
Keyless entry keypad autolock enable/disable procedure1. Turn the ignition off.2. Close all the doors.3. Enter factory–set 5–digit entrycode.4. Press
Note: The autounlock feature can be activated/deactivatedindependently of the autolock feature.Power door lock switch autounlock enable/disable proced
Keyless entry keypad autounlock enable/disable procedure1. Turn the ignition off.2. Close all the doors.3. Enter factory–set 5–digit entrycode.4. Pres
INTERIOR LUGGAGE COMPARTMENT RELEASEYour vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of esc
WARNING: Do not leave children, unreliable adults, or animalsunattended in the vehicle. On hot days, the temperature in thetrunk or vehicle interior c
Intelligent Access keyRefer to Intelligent Access in thissection for more features.Changes or modifications not expressly approved by the partyrespons
Intelligent Access (if equipped)WARNING: Radio waves from the Intelligent Access systemtransmitters in the vehicle may affect certain implanted medica
Push button start: Your vehicle is equipped with a push button startsystem, which allows you to start your vehicle without using a key. Tooperate the
Solid illumination after the engine is started indicates the On BoardDiagnostics System (OBD-II) has detected a malfunction. Refer to Onboard diagnost
Car finderPresstwice within three seconds. The horn will chirp and the turnlamps will flash. It is recommended that this method be used to locateyour
2. Press and hold either the 1 or 2control located on the seat sideshield for five seconds. (A tone willbe heard after 11⁄2seconds when thememory stor
2. Remove the old battery.Note: Please refer to localregulations when disposing oftransmitter batteries.3. Insert the new battery. Refer tothe instruc
Replacing lost Integrated Keyhead Transmitters (IKTs) or IntelligentAccess Keys (IA keys)If you would like to have your IKTs or IA keys reprogrammed b
Battery saverThe battery saver will shut off the lamps 10 minutes after the ignitionhas been turned off.• If the dome lamps were turned on using the p
The keypad can be operated with the factory set 5–digit entry code; thiscode is located on the owner’s wallet card in the glove box and isavailable fr
All personal codes are now erased and only the factory set 5–digit codewill work.Anti-scan featureIf the wrong code has been entered seven times (35 c
Your vehicle comes with two coded Integrated Keyhead Transmitters orIntelligent Access Keys; additional coded transmitters may be purchasedfrom your a
Automatic armingThe vehicle is armed immediately after switching the ignition to the offposition.The theft indicator will flash everytwo seconds to ac
Programming spare Integrated Keyhead Transmitter (IKT) keysIf you have a Intelligent Access Keys, refer to Programming spareintelligent access keys in
Airbag readiness: If this light failsto illuminate when the ignition isturned to on, continues to flash orremains on, have the systemserviced immediat
If the key has been successfully programmed it will start the vehicle’sengine and will operate the remote entry system (if the new key is anIntegrated
5. Press and release the brake pedal one time. The indicator on theStart/Stop button should begin to rapidly flash, indicating thatprogramming mode ha
• Press the driver or passengerpower door lock control while thedoor is open, then close the door.• Press and hold the 7 • 8 and 9 •0 controls on the
Pressing the power door unlock control within the 20 second prearmedmode will return the vehicle to a disarmed state.If equipped with Integrated Keyhe
SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o
To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o
To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous
WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Using the manual lumbar support (if eq
WARNING: Before returning the seatback to its originalposition, make sure that cargo or any objects are not trappedbehind the seatback. After returnin
Press either up or down on thelumbar control to select the top,middle, or bottom part of the seatback.Press the front of the lumbarcontrol to increase
Low washer fluid (RTT):Illuminates when the washer level inthe washer fluid reservoir is low.Door ajar (RTT): Illuminates inthe message center display
WARNING: Sitting improperly out of position or with the seatback reclined too far can take off weight from the seat cushionand affect the decision of
Press the control to recline theseatback forward or rearward.Using the power lumbar support (if equipped)The power lumbar control is locatedon the out
To operate the heated seats:Press once to activate the high heatsetting (2 indicator lights). Continuepressing to scroll through the othersettings; lo
To operate the cooled seats:Press once to activate the high coolsetting (three indicator lights).Continue pressing to scroll throughthe other settings
3. Remove filter.To install a filter:1. First, position the filter in it’shousing making sure that the farforward end is all the way up in thehousing.
The memory positions are also recalled when you press your remoteentry transmitter(unlock) control (if the transmitter is programmedto a memory positi
The non-adjustable head restraintsconsist of :• a trimmed energy absorbing foamand structure (1),• two steel stems (2),• and two guide sleeveunlock/re
WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjustable second row center head rest
2. Lower the head restraint bypressing and holding the guidesleeve adjust/release button andpushing down on the head restraint.Properly adjust the hea
2. Simultaneously press and holdboth the adjust/release button andthe unlock/remove button, then pullup on the head restraint.To reinstall the adjusta
more information on this system, refer to Tire pressure monitoringsystem (TPMS) in the Tires, Wheels and Loading chapter.Adaptive cruise control (ACC)
To lower the seatback(s) frominside the vehicle, pull the straplocated on the outboard side of theseatback to release it, and then foldseatback down.W
Rear heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cord
The indicator light will illuminate when the heated seats have beenactivated.SAFETY RESTRAINTSPersonal Safety System™The Personal Safety System™ provi
appropriate to activate these safety devices. Front airbags are designedto activate only in frontal and near-frontal collisions (not rollovers, sideim
WARNING: Always transport children 12 years old and under inthe back seat and always properly use appropriate childrestraints.The front passenger sens
The Restraints Control Module (RCM) monitors its own internal circuitsand the circuits for the airbag supplemental restraints, crash sensor(s),safety
WARNING: In a rollover crash, an unbelted person issignificantly more likely to die than a person wearing a seat belt.WARNING: Each seating position i
2. To unfasten, press the releasebutton and remove the tongue fromthe buckle.All restraints in the vehicle are combination lap and shoulder belts.Whil
Automatic locking modeWhen to use the automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to
How to disengage the automatic locking modeWARNING: Ford Motor Company recommends that allpassenger safety belt assemblies and attaching hardware shou
Key-in-ignition warning chime: Sounds when the key is left in theignition in the off or accessory position and the driver’s door is opened.Headlamps o
WARNING: The driver and front passenger safety belt system(including retractors, buckles and height adjusters) must bereplaced if the vehicle is invol
Belt-Minder姞The Belt-Minder威 feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders byinterm
If... Then...The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately1 minute while the vehicle istraveling at least 3 mph(5 km
Reasons given... Consider...“Traffic is light” Nearly 1 of 2 deaths occur insingle-vehicle crashes, many whenno other vehicles are around.“Belts wrink
Note: If you are using MyKey™, the Belt-Minder威 cannot be disabled.Also, if the Belt-Minder威 has been previously disabled, it will bere-enabled during
• This will enable the Belt-Minder威 feature for that seating position if itis currently disabled. As confirmation, the safety belt warning light willf
Important supplemental restraint system precautionsAirbags DO NOT inflate slowly orgently and the risk of injury from adeploying airbag is greatest cl
WARNING: Do not put anything on or over the airbag module.Placing objects on or over the airbag inflation area may causethose objects to be propelled
How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suffic
WARNING: If the air bag has deployed, the air bag will notfunction again and must be replaced immediately. If the airbag is not replaced, the unrepair
WARNING: Never remove the coolant reservoir cap while theengine is running or hot.Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel
• the system determines that an infant is present in a rear-facing infantseat that is installed according to the manufacturer’s instructions,• the sys
• When the front passenger sensing system enables the front passengerfrontal airbag (may inflate), the indicator will be unlit and stay unlit.If a per
WARNING: Sitting improperly out of position or with the seatback reclined too far can take off weight from the seat cushionand affect the decision of
WARNING: To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a chi
WARNING: Any alteration/modification to the front passengerseat may affect the performance of the front passenger sensingsystem.Determining if the sys
WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. Contact your authorize
The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of
WARNING: Do not attempt to service, repair, or modify theSafety Canopy威 system, its fuses, the A, B, or C pillar trim, orthe headliner on a vehicle co
• Two crash sensors mounted on the B pillar (one on each side of thevehicle).• Two crash sensors located at the C pillar behind the rear doors (oneon
WARNING: If the SafetyCanopy威 system hasdeployed, the Safety Canopy威 willnot function again unless replaced.The Safety Canopy威 system(including the A,
MESSAGE CENTERYour vehicle’s message center allows you to configure/personalize certainvehicle options to suit your needs.The message center is also c
The system can be turned off when any one of the following actions aretaken by the driver or any other person:• pressing the hazard control button,• o
Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfantsortoddlersChildren weighing 40 lb
Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe
WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli
Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle.If the child is the proper height, age, and weigh
Installing child safety seats with combination lap and shoulderbeltsCheck to make sure the child seat is properly secured before each use.Children 12
1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
9. Attach the tether strap (if the child seat is equipped). Refer toAttaching child safety seats with tether straps later in this chapter.10. Before p
Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol.The LATCH anchors are locat
Locks and Security 111Keys 111Locks 119Anti-theft system 136Seating and Safety Restraints 144Seating 144Safety restraints 162Airbags 175Child restrain
If you calculate your average fuel economy by dividing distance traveledby gallons of fuel used (liters of fuel used by 100 kilometers traveled),your
WARNING: Never attach two child safety seats to the sameanchor. In a crash, one anchor may not be strong enough to holdtwo child safety seat attachmen
Attaching child safety seats with tether strapsMany forward-facing child safety seats include a tether strap whichextends from the back of the child s
3. Open the tether anchor cover.4. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safety seat maynot
Although the lap/shoulder belt will provide some protection, childrenwho have outgrown a typical child seat are still too small for lap/shoulderbelts
Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli
WARNING: The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydro
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
System check and vehicle feature customizationPress the SETUP button repeatedlyto cycle the message center throughthe following features:RESET FOR SYS
WARNING: Under-inflation is the most common cause of tirefailures and may result in severe tire cracking, tread separationor ⬙blowout⬙, with unexpecte
Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo
Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w
• Do not run over curbs or hit the tire against a curb when parkingWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the
• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/All Wheel Drive (AWD)vehicles (
Sometimes irregular tire wear can be corrected by rotating the tires.Note: If your tires show uneven wear ask an authorized dealer to checkfor and cor
3. 65: Indicates the aspect ratio which gives the tire’s ratio of height towidth.4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or ri
8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n
3. Once “OIL LIFE SET TO XXX%” is displayed, release and press theRESET button to change the Oil Life Start Value. Each release and presswill reduce t
13. Maximum Permissible Inflation Pressure: Indicates the tiremanufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw
Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti
When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.
Low Tire PressureWarning LightPossible cause Customer Action RequiredFlashing WarningLightSpare tire in use Your temporary spare tire is inuse. Repair
SNOW TIRES AND CHAINSWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel
SUMMER TIRESYour Taurus SHO may be equipped with summer tires to providesuperior performance on wet and dry roads. Summer tires do not havethe Mud and
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Press RESET to turn the warning chime on or off. The system will revertto chime on each time the vehicle is started. The heads up display and/orchime
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle.3. Subtract the combined weight of the driver and pas
1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now youhave the load capacity to transport the cement and your friend home.In metric units,
If you use a rental trailer, follow the instructions that the rental agencygives to you.Do not attach safety chains to the bumper.Trailer brakesElectr
• It is recommended to select the L (Low) gear position when additionalengine braking is needed. In situations such as prolonged downhilldriving on st
Front Wheel Drive (FWD) vehicles:Tow your Front Wheel Drive vehicle with all four wheels on the groundor with the front wheels off the ground by using
STARTINGPositions of the ignition (if equipped)If your vehicle is equipped with a push button start system, refer toPush button start system in this s
System warningsSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems.In the event of a multiple warning si
WARNING: Do not start your vehicle in a closed garage or inother enclosed areas. Exhaust fumes can be toxic. Always openthe garage door before you sta
• Make sure the gearshift lever is inP (Park).3. Turn the key to 3 (on) withoutturning the key to 4 (start).If your vehicle is equipped with apush but
3. After idling for a few seconds, release the parking brake, apply thebrake, shift into gear and drive.Note: If the engine does not start on the firs
3. On — press and hold the START/STOP button for at least one secondwithout applying the brake pedal. This will power your vehicle’s electricalsystem
Fast Restart Feature: The Fast Restart feature allows you to re-startyour vehicle within 20 seconds of switching the vehicle off, if a valid IAkey is
Important ventilating informationIf the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least 1 inch (2.5
• To reduce the risk of electrical shock, do not use your heater withungrounded electrical systems or two pronged (cheater) adapters.Also ensure that
Refer to Warning lights andchimes in the Instrument Clusterchapter for information on the brakesystem warning light.Four-wheel anti-lock brake system
Even when the ABS is disabled,normal braking is still effective. Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake
Press the parking brake pedaldownward again to release theparking brake. Driving with theparking brake on will cause thebrakes to wear out quickly and
CHECK PARK AID (if equipped) — Displayed when the transmissionis in R (Reverse) and the reverse sensing system (park aid) is disabled.Refer to Rear pa
WARNING: If a failure has been detected within theAdvanceTrac威 system, the “sliding car” iconwill illuminatesteadily, and you may hear a chime. If equ
When an event occurs that activates AdvanceTrac威 you may experiencethe following:• A slight deceleration of the vehicle• The “sliding car”indicator li
Electronic Stability Control (ESC)Electronic stability control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa
AdvanceTrac威 FeaturesControlswitchfunctionsMode“Slidingcar off”iconMessageCenterDisplay (ifequipped)ESC TCSDefault atstart-upSystemInitializationTurns
STEERING3.5L V6 engine (SHO): Your vehicle is equipped with an electric powersteering (EPS) system. There is no fluid reservoir to check or fill.If yo
a few seconds when the engine is running. If the power steering systembreaks down (or if the engine is turned off), you can steer the vehiclemanually,
1. Apply the parking brake.2. Remove the cup holder insert.3. Using a screwdriver (or similartool), remove the protective coverto the interlock releas
Understanding the gearshift positions of the 6–speed automatictransmission with transmission control switch (if equipped)Your vehicle has been designe
D (Drive) with Grade AssistPressing the transmission controlswitch on the side of the gearshiftlever activates Grade Assist.Grade Assist• Improves dri
Understanding the gearshift positions of the 6–speed withSelectShift Automatic™ transmission (SST) (if equipped)Your vehicle has been designed to impr
AWD OFF (if equipped) — Displayed when the AWD system has beenautomatically disabled to protect itself. This is caused by operating thevehicle with th
N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D
Recommended shift speedsUpshift according to the following chart:Upshifts when accelerating (recommended for best fueleconomy)Shift from:1 - 2 15 mph
WARNING: To help avoid personal injury, always use cautionwhen in R (Reverse) and when using the RSS.WARNING: This system is not designed to prevent c
The RSS automatically turns on when the gearshift lever is placed in R(Reverse) and the ignition is on. An RSS control on the instrument panelallows t
Use the side mirrors and rearview mirror to get better coverage on bothsides and rear of the vehicle.Image delay if displayed through the rear view mi
Night time and dark area useAt night time or in dark areas, the camera system relies on the reverselamp lighting to produce an image. Therefore it is
OperationThe radar sensor detects vehiclesahead that are moving in the samedirection as your vehicle.If the radar detects that yourvehicle is rapidly
WARNING: The collision warning system’s brake support canonly help reduce the speed at which a collision occurs if thedriver applies the vehicle’s bra
Note: If the system cannot be turned off in a MyKey™ equipped vehicle,refer to MyKey™ in the Locks and Security chapter for moreinformation.Note: If c
The BLIS威 and CTA has an yellowindicator (also referred to as thealert) located in the left and rightexterior mirrors. When the vehicle isstarted, the
INTKEY COULD NOT PROGRAM — Displayed when an attempt ismade to program a fifth integrated key to the remote key entry system.For more information on i
• Vehicles passing through the blind zone at very fast rates• Severe weather conditions• When several vehicles forming a convoy pass through the blind
The CTA system detects vehicles approaching up to 45 feet (14 meters)away (approximately the width of five parking spaces). Coveragedecreases when veh
CTA coverage also decreases when parking at shallow angles (refer tofigure for approximate zone coverage areas [sensor obstructed forvehicle on left])
CTA and Reverse Sensing System (RSS) interactionCTA works along with the Reverse Sensing System (RSS) (if equipped).Become familiar with the warning t
WARNING: Just prior to the system recognizing a blockedcondition and alerting the driver, the number of missed objectswill increase. To help avoid inj
Trailer tow false alertsWhen towing a trailer, the sensors may detect the trailer thus causing afalse alert. It may be desirable to turn the BLIS威 off
location and allow it to idle. The AWD OFF message will turn off whenthe system cools and normal AWD function returns.Note: Your AWD vehicle is not in
If your vehicle gets stuckIf your vehicle gets stuck in mud or snow it may be rocked out byshifting between forward and reverse gears, stopping betwee
• If the vehicle goes from one type of surface to another (i.e., fromconcrete to gravel) there will be a change in the way the vehicleresponds to a ma
Driving through deep water may damage the engine ortransmission.If the front or rear axle is submerged in water, the axle lubricant andPTU (Power Tran
SHIFT TO PARK (if equipped) — Displayed when the start/stopbutton is pressed to shut off the engine with the shift select lever in anyposition other t
Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;
Maintenance and ModificationsThe suspension and steering systems on your vehicle have been designedand tested to provide predictable performance wheth
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co
FUEL PUMP SHUT-OFFIn the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fue
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
Passenger compartment fuse panelThe fuse panel is located under the instrument panel to the left of thesteering wheel.The fuses are coded as follows.F
Fuse/RelayLocationFuse AmpRatingProtected Circuits8 10A Low beam headlamps (right)9 15A Interior lights, Cargo lamps10 15A Switch illumination, Puddle
Fuse/RelayLocationFuse AmpRatingProtected Circuits29 5A Instrument panel cluster, Heads updisplay30 5A Not used (spare)31 10A Not used (spare)32 10A A
Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot
VEHICLE SPEED 80 MPH MAX — Displayed when a MyKey™ is inuse and the Admin has enabled the MyKey speed limit and the vehiclespeed is 80 mph (130 km/h).
The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPower Circuits1 80A** Passenger compartment fusepanel power2 80A** Passeng
Fuse/RelayLocationFuse AmpRatingPower Circuits26 10A* Backup relay27 25A* Fuel pump28 80A** Engine cooling fan29 — Not used30 — Not used31 — Not used3
Fuse/RelayLocationFuse AmpRatingPower Circuits53 Half ISO relay PCM power relay54 — Not used55 Half ISO relay Front wiper relay56 Half ISO relay Rear
WARNING: Refer to Tire Pressure Monitoring System (TPMS)in the Tires, Wheels and Loading chapter for importantinformation. If the tire pressure monito
Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following:• Handling, stability and braki
Stopping and securing the vehicle1. Park on a level surface, set theparking brake and activate hazardflashers.2. Place gearshift lever in P (Park)and
WARNING: To help prevent the vehicle from moving when youchange a tire, be sure to place the transmission in P (Park), setthe parking brake and block
3. Put the jack in the jack notchnext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is completely off theground.Note: DO
Stowing the tire and jack1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown.
If you are stowing the flat tire:1. Remove the extension bolt fromthe exterior pocket of the felt bag.2. Install the jack as shown inStep 4 under Stow
Customer Assistance 316Reporting safety defects (U.S. only) 322Reporting safety defects (Canada only) 322Cleaning 323Maintenance and Specifications 33
AUDIO SYSTEMSNote: If your volume is muted and MYKEY VOLUME LIMITED isdisplayed, refer to MyKey™ in the Locks and Security chapter for moreinformation
1. Air compressor (inside)2. Diverter knob3. On/Off button4. Air pressure gauge5. Deflation button6. Sealant bottle/canister7. Sealant filling clear t
• Read the information in the Tips for use of the temporary mobilitykit section to ensure safe operation of the temporary mobility kit andyour vehicle
What to do when a tire is puncturedA tire puncture within the tire’s tread area can be repaired in two stageswith the temporary mobility kit:• In the
7. Turn dial (1) counterclockwise tothe sealant position. Turn on the kitby pressing the on/off button (2).8. Inflate the tire to the pressurelisted o
10. Immediately and cautiously, drive the vehicle 4 miles (6 km)to distribute the sealant evenly inside the tire. Do not exceed50 mph (80 km/h).Note:
WARNING: The power plug may get hot after use and shouldbe handled carefully while unplugging.What to do after the tire has been sealedAfter using the
2. Press the button located on thetemporary mobility kit compressorhousing below the canister whilepulling up on the sealant canister.Installation of
2. Once aligned, seat the sealantcanister by lightly pushing downuntil you hear an audible click.3. Wrap the clear tube around thecompressor housing.N
Bolt size Wheel lug nut torque*lb.ft. N•m1/2-20 UNF 100 135* Torque specifications are for nut and bolt threads free of dirt andrust. Use only Ford re
WARNING: Do not insert the nozzle of portable fuel containersor aftermarket funnels into the Easy Fuel™ system. This coulddamage the fuel system and i
Setting the clockTo set the time, press CLOCK. Thedisplay will read SET TIME. Use thememory preset numbers (0–9) toenter in the desired time–hours and
Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
If the vehicle is towed by other means or incorrectly, vehicledamage may occur.Ford Motor Company produces a towing manual for all authorized towtruck
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized
In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph
In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext
procedure outlined on the first page of the Customer Assistance section,you may be eligible to participate in the BBB AUTO LINE program.The BBB AUTO L
Saving presets automatically: Autoset allows you to set the strongestlocal radio stations without losing your original manually set presetstations for
The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have
If you are in another foreign country, contact the nearest authorizeddealer. If the authorized dealer employees cannot help you, they candirect you to
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i
WAXING• Wash the vehicle first.• Do not use waxes that contain abrasives; use Motorcraft威 PremiumLiquid Wax (ZC-53-A), which is available from your au
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:•Take care when u
3.5L V6 SHO ENGINEPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authori
• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft威 Premium Windshield Washer Concentrate (ZC-32-A),available from your a
If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows:1. Wipe up spilled liqui
LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• For routine cleaning, wipe the surface wit
CD/MP3 PlayerCD: Press to enter CD/MP3 mode. Ifa disc is already loaded into thesystem, CD/MP3 play will beginwhere it ended last. If no CD is loaded,
FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column.2. Go to th
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.5L V6 engine1. Power steering fluid reservoir2. Engine coolant reservoir3. Brake fluid reservoir4. B
3.5L V6 SHO engine1. Engine coolant reservoir2. Brake fluid reservoir3. Battery4. Power distribution box5. Air filter assembly6. Automatic transmissio
Engine shieldSome vehicles may be equippedwith an aero-shield under theengine. This shield needs to beremoved for service, including oiland filter cha
CHANGING THE WIPER BLADES1. Pull the wiper blade and armaway from the glass.2. Squeeze the locking tabs torelease the blade from the arm andpull the b
5. Locate and carefully remove theengine oil level dipstick.6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil l
• Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine isoverfilled, some oil must beremoved from the e
Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol con
SEEK: Press SEEK toaccess the previous/next track.CAT (Category) / FOLD(Folder):In MP3 mode only– PressCAT/FOLD and thenpressSEEK to access the previo
For longer, trouble-free operation, keep the top of the battery clean anddry. Also, make certain the battery cables are always tightly fastened tothe
Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe bat
ENGINE COOLANTChecking engine coolantThe concentration and level of engine coolant should be checked at theintervals listed in scheduled maintenance i
low or empty, add engine coolant to the reservoir. Refer to Addingengine coolant in this chapter.Note: Automotive fluids are not interchangeable; do n
• Do not add extra inhibitors or additives to the coolant. Thesecan be harmful and compromise the corrosion protection of the enginecoolant.For vehicl
If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your coolin
• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damag
When fail-safe mode is activatedYou have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be ab
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsWARNING: Do not overfill the fuel tank. The pressure in anoverfilled tank may c
• Fuels can also be harmful if absorbed through the skin. If fuel issplashed on the skin and/or clothing, promptly remove contaminatedclothing and was
Satellite Radio (if equipped)Satellite radio is available only with a valid SIRIUS威 radiosubscription. Check with your authorized dealer for availabil
• Keep the fuel pump nozzle in contact with the fuel container whilefilling.• DO NOT use a device that would hold the fuel pump handle in the fillposi
WARNING: The fuel system may be under pressure. If you heara hissing sound near the fuel filler door (Easy Fuel™ “no cap”fuel system), do not refuel u
Some stations offer fuels posted as⬙Regular⬙ with an octane ratingbelow 87, particularly in highaltitude areas. Fuels with octanelevels below 87 are n
Refilling with a portable fuel containerWith the Easy Fuel™ “no cap” fuel system, use the following directionswhen filling from a portable fuel contai
4. When done, clean the funnel or properly dispose of it. Extra funnelscan be purchased from your authorized dealer if you choose to disposeof the fun
• Use the same side of the same pump and have the vehicle facing thesame direction each time you fill up.• Have the vehicle loading and distribution t
• Slow down gradually.• Driving at reasonable speeds (traveling at 55 mph [88 km/h] uses 15%less fuel than traveling at 65 mph [105 km/h]).• Revving t
• Transmissions give their best fuel economy when operated in the topcruise gear and with steady pressure on the gas pedal.• Close windows for high sp
An improperly operating or damaged exhaust system may allow exhaustto enter the vehicle. Have a damaged or improperly operating exhaustsystem inspecte
If the service engine soon indicator remains on, have your vehicleserviced at the first available opportunity. Although some malfunctionsdetected by t
TEXT: Press and release to displaythe artist and song title. While inTEXT MODE, press again to scrollthrough the Artist (AR), Song (SO), Channel (CH)
POWER STEERING FLUID (EXCEPT SHO ENGINE)Refer to scheduled maintenance information.1. Start the engine and let it rununtil it reaches normal operating
TRANSMISSION FLUIDChecking automatic transmission fluidRefer to your scheduled maintenance information for scheduledintervals for fluid checks and cha
The transmission fluid should bewithin the cross-hatch area if atnormal operating temperature180°F-200°F (82°C-93°C).High fluid levelFluid levels abov
WARNING: To reduce the risk of vehicle damage and/orpersonal burn injuries do not start your engine with the aircleaner removed and do not remove it w
6. Replace the air filter housingcover and secure the clamps. Besure that the air cleaner cover tabsare engaged into the slots of the aircleaner housi
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItems CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationBrake fluidBetween MAXan
Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine coolant11.1 quarts(10.5L)Motorcraft威 Specialty GreenEngine Coolant
ENGINE DATAEngine 3.5L V6 engine 3.5L V6 SHO engineCubic inches 214 214FuelSee Octanerecommendationsearlier in this chapter.See Octanerecommendations
3.5L V6 SHO engineIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requireth
Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX
titles, the display will read REPLACE SONG? Press OK to access thesaved titles and pressSEEK to cycle through the saved titles.When the song title app
TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
Peace of mindRemote startVehicle security systemsWheel locksFor maximum vehicle performance, keep the following information inmind when adding accesso
FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on
Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With
Ford Extended Service Plan3752010 Taurus (500)Owners Guide, 2nd PrintingUSA (fus)
AAccessory delay ...83Adaptive Cruise Control ...88AdvanceTrac ...249AdvanceTrac Sport Mod
Cargo cover ...84Cargo net ...110CD ...30Ce
through water ...278, 281EElectronic message center ...19Emergencies, roadsidejump-starting ...309running o
Heatingheating and air conditioningsystem ...49, 52, 54Homelink wireless controlsystem ...
b. CHANGE PIN: Press OK when CHANGE PIN is displayed. Thedisplay will read ENTER OLD PIN. Enter your current (old) PINnumber and when the system accep
Motorcraft威 parts ...330, 364Multi-contour seats ...148MyKey ...113NNavigation system
Safety restraints - LATCHanchors ...198Safety seats for children ...194Safety ComplianceCertification Label
remote release ...110, 130Turn signal ...67UUniversal garage door opener ...99USB port ...
Extra FeaturesAUX: Press repeatedly to cyclethrough LINE (auxiliary audiomode) and SYNC威 (if equipped).For auxiliary jack location and further informa
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
Your vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicplayer to the in-vehic
Troubleshooting:1. Do not connect the audio input jack to a line level output. Line leveloutputs are intended for connection to a home stereo and are
Your vehicle may be equipped with aUSB port inside your center console.This feature allows you to plug inmedia playing devices, memorysticks, and also
CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C
CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio forthe selectedchannel.No action required. Thisme
Radio Display Condition Action RequiredNO TEXT Categoryinformation notavailable.Category information notavailable at this time onthis channel. The sys
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the
Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti
4. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. A/Cengages automaticall
During extreme high ambient temperatures when idling stationary forextended periods of time in gear, it is recommended to run the A/C inthe MAX A/C mo
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the In
4. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. A/Cengages automaticall
12. Power/Driver temperature: Press to activate/deactivate theclimate control system. When the system is off, outside air is preventedfrom entering th
Temperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the Instrument Cluster chapter.1. CLIMATE: Press to contro
10. Driver temperature: Press to increase/decrease the air temperaturefor the driver side of the vehicle. This control also adjusts the passengerside
• : Distributes air through the floor vents, rear seat floor vents.•: Distributes air through the windshield defroster vents, de-mistervents, floor ve
For maximum cooling performance:• Automatic operation:1. Press AUTO for full automatic operation.2. Do not override A/C or(recirculated air).3. Set th
CABIN AIR FILTERThe cabin air filter element is designed to reduce the concentration ofairborne particles such as dust, spores and pollen in the air b
Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the low beam headlampso
3. Turn the ignition switch to on and then back to off.4. Turn the headlamp control to the autolamp position. The headlampswill turn on.5. Wait the de
Operation - The high beam switch can be used to turn the high beamson. They will then remain on until the switch has been returned to theneutral posit
• The vehicle speed falls below 27 mph (43 km/h).• The ambient light level is high enough that high beams are notneeded.• Severe rain, snow or fog is
Typical road dust, dirt and water spots will not affect the automatic highbeam system’s performance. However, in cold or inclement weatherconditions,
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicablelit components in the vehicle duringheadlamp and parking lam
3. Turn on the low beam headlamps to illuminate the wall or screen andopen the hood.To see a clearer light pattern for adjusting, you may want to bloc
TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSDome lamps and map lampsThe ma
Ambient lighting (if equipped)Illuminates footwells and cupholderswith a choice of several colors. Theambient lighting control is located inthe center
Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an
Event Data RecordingOther modules in your vehicle — event data recorders — arecapable of collecting and storing data during a crash or nearcrash event
Replacing headlamp (low/high beam) bulbs1. Make sure the headlamp switch is in the off position, then open thehood.2. Reach in behind the headlamp ass
3. Remove the bulb socket byturning it counterclockwise andpulling it straight out.4. To remove the bulb, pull itstraight out of the bulb socket.Insta
4. Remove the bulb socket byrotating it counterclockwise, thenpulling it out of the lamp assembly.5. Pull the bulb straight from thesocket.Install new
Replacing license plate lamp bulbs1. Make sure the headlamp switch isin the off position.2. Remove the two screws from thelicense plate lamp assembly.
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
Windshield washer: Push the endof the stalk:• briefly: causes a single swipe ofthe wipers without washer fluid.• a quick push and hold: the wiperswill
WARNING: Never adjust the steering wheel when the vehicle ismoving.ILLUMINATED VISOR MIRRORLift the mirror cover to turn on thevisor mirror lamp.Slide
Storage compartmentThe storage compartment may beused to store a pair of sunglasses.Press the release area on the rearedge of the bin door to open the
Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the on p
2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons.3. Slowly d
information”) only to help provide you with the directions, trafficreports, or business searches you request. If you do not wantFord or its vendors to
Some consoles will have panel doorscovering the cupholders andswitches. Press the doors to openthem.Some cupholders will be equippedwith a divider. Pu
• do not leave battery chargers, video game adapters, computers andother devices plugged in overnight or when the vehicle is parked forextended period
One-touch up or downThis feature allows the driver’s and passenger’s window to open or closefully without holding the control down.Driver’s window one
If the switch is pressed and held to the normal open or one-touch downposition during a one-touch up cycle, the window will stop. If, after1/2 second
POWER REAR SUNSHADE (IF EQUIPPED)Your vehicle may be equipped with apower rear sunshade that covers therear window of your vehicle. Thecontrol is loca
Note: If equipped with a rear view camera system, a video image will bedisplayed in the mirror or the navigation system display (if equipped)when the
Fold-away mirrorsPull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.POWER ADJUSTABLE FOOT PEDALS (IF EQU
Using speed controlThe speed controls are located on the steering wheel. The followingbuttons work with speed control:RESUME: Press to resume a setspe
Increasing speed while using speed controlTo set a higher speed:• Press and hold SET + until you get to the desired speed, then release.You can also u
WARNING: Always pay close attention to changing roadconditions, especially when using Adaptive Cruise Control.Adaptive Cruise Control cannot replace a
EXPORT UNIQUE (NON–UNITED STATES/CANADA) VEHICLESPECIFIC INFORMATIONFor your particular global region, your vehicle may be equipped withfeatures and o
3. Press and release the SET +control. The vehicle speed will bestored in the memory and themessage center will display SETXXX MPH (your desired speed
braking which is applied by the ACC system is limited and can beoverridden by the driver applying the brakes.If the ACC system predicts that itsmaximu
Note: It is the driver’s responsibility to select a gap appropriate to thedriving conditions.Disengaging adaptive cruise controlPress the brake pedal
Resuming the set speedPress and release the RESUMEcontrol. This will automaticallyreturn the vehicle to the previouslyset speed. The set speed will di
Turning off cruise controlPress the OFF button to turn off thecruise control.Note: When you turn off the cruisecontrol or the ignition, your cruisecon
• There may be issues with the detection of vehicles in front whendriving into and coming out of a bend or curve in the road.In these cases ACC may br
Cause ActionThe surface of the radar in thegrille is dirty or obstructed insome wayClean the grille surface in front ofthe radar or remove the objectc
STEERING WHEEL CONTROLS (IF EQUIPPED)Radio control featuresVOL + (Volume): Press to increasethe volume.VOL – (Volume): Press to decreasethe volume.(Se
SYNC威 system hands freecontrol feature (if equipped)Press briefly to use the voicecommand feature. You will hear atone and LISTENING will appear inthe
To open the moon roof: Press andrelease the SLIDE control, the moonroof will open automatically. Pressthe switch again to stop the moonroof.WARNING: W
Commentaires sur ces manuels