Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Message center 19Entertainment Systems 30AM/FM stereo with CD/MP3 30Auxiliary
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
5. Firmly press and release the “learn” or “smart” button. (The name andcolor of the button may vary by manufacturer.)Note: There are 30 seconds in wh
Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet
Car2U姞 Home Automation System (if equipped)The Car2U威 Home AutomationSystem is a universal transmitterlocated in the driver’s visor thatincludes two p
• Fixed code garage door openers were produced prior to 1996. Fixedcode uses the same coded signal every time. It is manuallyprogrammed by setting DIP
2. Go to the garage to locate thegarage door opener motor and its“learn” button. You may need aladder to reach the unit and youmay need to remove the
Note: The Car2U威 system allows for three devices to be programmed. Ifyou need to change or replace any of the three devices after it has beeninitially
3. To input these positions into theCar2U威 system, simultaneouslypress all three Car2U威 systembuttons for a few seconds and thenrelease to put the dev
To erase programming on the Car2U威 system (individual buttons cannotbe erased), use the following procedure:1. Firmly press the two outsideCar2U威 syst
INTERIOR TRUNK CONTROLThe trunk release button is locatedon the instrument panel near theradio. Press the button to open thetrunk.CARGO AREA FEATURESC
KEYSIntegrated Keyhead Transmitters (IKTs) (If equipped)Your vehicle may be equipped withtwo Integrated KeyheadTransmitters (IKTs). The key bladefunct
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
Intelligent Access Key (IA key) (if equipped)Your vehicle may be equipped withtwo Intelligent Access keys whichoperate the power locks and theremote e
POWER DOOR LOCKS• Press thecontrol to unlock alldoors.• Press thecontrol to lock alldoors.Smart unlocksThis feature helps to prevent you from locking
If your vehicle’s perimeter alarm is in the armed state, the smart unlockfeature will not allow you to lock your IA key inside the trunk. When thealar
Deactivating/activating autolock featureYour vehicle comes with the autolock features activated; there are fourmethods to enable/disable this feature:
Keyless entry keypad autolock enable/disable procedure1. Turn the ignition off.2. Close all the doors.3. Enter factory–set 5–digit entrycode.4. Press
Note: The autounlock feature can be activated/deactivatedindependently of the autolock feature.Power door lock switch autounlock enable/disable proced
Keyless entry keypad autounlock enable/disable procedure1. Turn the ignition off.2. Close all the doors.3. Enter factory–set 5–digit entrycode.4. Pres
INTERIOR LUGGAGE COMPARTMENT RELEASEYour vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of esc
WARNING: Do not leave children, unreliable adults, or animalsunattended in the vehicle. On hot days, the temperature in thetrunk or vehicle interior c
Intelligent Access keyRefer to Intelligent Access in thissection for more features.Changes or modifications not expressly approved by the partyrespons
WARNING LIGHTS AND CHIMESStandard instrument cluster shown, optional cluster similarWarning lights and gauges can alert you to a vehicle condition tha
Intelligent Access (if equipped)WARNING: Radio waves from the Intelligent Access systemtransmitters in the vehicle may affect certain implanted medica
Push button start: Your vehicle is equipped with a push button startsystem, which allows you to start your vehicle without using a key. Tooperate the
Car finderPresstwice within three seconds. The horn will chirp and the turnlamps will flash. It is recommended that this method be used to locateyour
2. Press and hold either the 1 or 2control located on the seat sideshield for five seconds. (A tone willbe heard after 11⁄2seconds when thememory stor
2. Remove the old battery.Note: Please refer to localregulations when disposing oftransmitter batteries.3. Insert the new battery. Refer tothe instruc
Replacing lost Integrated Keyhead Transmitters (IKTs) or IntelligentAccess Keys (IA keys)If you would like to have your IKTs or IA keys reprogrammed b
Battery saverThe battery saver will shut off the lamps 10 minutes after the ignitionhas been turned off.• If the dome lamps were turned on using the p
SECURICODE™ KEYLESS ENTRY SYSTEMThe keypad, located near the driver’s window, is invisible until touchedand then it lights up so you can see and touch
4. For memory recall feature, enter the sixth digit 1 • 2 to store driver 1settings or 3 • 4 to store driver 2 settings.Note: Touching 5 • 6, 7 • 8, o
two-stage unlocking, refer to the Central Unlocking/Two stageunlocking section earlier in this chapter.To unlock all doors, enter the factory set code
Solid illumination after the engine is started indicates the On BoardDiagnostics System (OBD-II) has detected a malfunction. Refer to Onboard diagnost
engine. If a problem occurs, turn the ignition off, remove all objects onthe key chain away from the coded key and restart the engine.Note: Do not lea
Replacement Integrated Keyhead Transmitters (IKT) and codedkeys or Intelligent Access KeysNote: Your vehicle comes equipped with two Integrated Keyhea
• If two previously programmed coded keys are not available, you musttake your vehicle to your authorized dealer to have the spare key(s)programmed.Pl
You must have two previously programmed Intelligent Access Keys insidethe vehicle and the new unprogrammed Intelligent Access Keys readilyaccessible.
Note: To program MyKey™ features, refer to MyKey™ in this chapter.MYKEY™The MyKey™ feature allows you to program a restricted driving mode topromote g
Create a MyKey™To program MyKey™ on one of the keys programmed to the vehicle,insert it into the ignition. (For vehicles equipped with push button sta
6. Repeat steps 4 and 5 until you are done changing the optionalsettings.Disable MyKey™To reset all MyKeys™ as Admin keys do the following:1. Turn the
TroubleshootingCondition Potential CausesCan’t create a MyKey™ • Key in the ignition is already aMyKey™• Key in the ignition is the lastremaining Admi
Arming the systemWhen armed, this system will respond if unauthorized entry isattempted. When unauthorized entry occurs, the system will flash theturn
Disarming the systemYou can disarm the system by any of the following actions:• Unlock the doors by using your transmitter.• Unlock the doors by using
Airbag readiness: If this light failsto illuminate when the ignition isturned to on, continues to flash orremains on, have the systemserviced immediat
SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o
To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o
To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous
WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Using the manual lumbar support (if eq
WARNING: Before returning the seatback to its originalposition, make sure that cargo or any objects are not trappedbehind the seatback. After returnin
Press either up or down on thelumbar control to select the top,middle, or bottom part of the seatback.Press the front of the lumbarcontrol to increase
WARNING: Sitting improperly out of position or with the seatback reclined too far can take off weight from the seat cushionand affect the decision of
Press the control to recline theseatback forward or rearward.Using the power lumbar support (if equipped)The power lumbar control is locatedon the out
To operate the heated seats:Press once to activate the high heatsetting (2 indicator lights). Continuepressing to scroll through the othersettings; lo
To operate the cooled seats:Press once to activate the high coolsetting (three indicator lights).Continue pressing to scroll throughthe other settings
Low washer fluid (RTT):Illuminates when the washer level inthe washer fluid reservoir is low.Door ajar (RTT): Illuminates inthe message center display
3. Remove filter.To install a filter:1. First, position the filter in it’shousing making sure that the farforward end is all the way up in thehousing.
The memory positions are also recalled when you press your remoteentry transmitter(unlock) control (if the transmitter is programmedto a memory positi
The non-adjustable head restraintsconsist of :• a trimmed energy absorbing foamand structure (1),• two steel stems (2),• and two guide sleeveunlock/re
WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjustable second row center head rest
2. Lower the head restraint bypressing and holding the guidesleeve adjust/release button andpushing down on the head restraint.Properly adjust the hea
2. Simultaneously press and holdboth the adjust/release button andthe unlock/remove button, then pullup on the head restraint.To reinstall the adjusta
To lower the seatback(s) frominside the vehicle, pull the straplocated on the outboard side of theseatback to release it, and then foldseatback down.W
Rear heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cord
The indicator light will illuminate when the heated seats have beenactivated.SAFETY RESTRAINTSPersonal Safety System姞The Personal Safety System威 provi
appropriate to activate these safety devices. Front airbags are designedto activate only in frontal and near-frontal collisions (not rollovers, sideim
more information on this system, refer to Tire pressure monitoringsystem (TPMS) in the Tires, Wheels and Loading chapter.Adaptive cruise control (ACC)
WARNING: Always transport children 12 years old and under inthe back seat and always properly use appropriate childrestraints.The front passenger sens
The Restraints Control Module (RCM) monitors its own internal circuitsand the circuits for the airbag supplemental restraints, crash sensor(s),safety
WARNING: In a rollover crash, an unbelted person issignificantly more likely to die than a person wearing a seat belt.WARNING: Each seating position i
2. To unfasten, press the releasebutton and remove the tongue fromthe buckle.All restraints in the vehicle are combination lap and shoulder belts.Whil
Automatic locking modeWhen to use the automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to
How to disengage the automatic locking modeWARNING: Ford Motor Company recommends that allpassenger safety belt assemblies and attaching hardware shou
WARNING: The driver and front passenger safety belt system(including retractors, buckles and height adjusters) must bereplaced if the vehicle is invol
Belt-Minder姞The Belt-Minder威 feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders byinterm
If... Then...The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately1 minute while the vehicle istraveling at least 3 mph(5 km
Reasons given... Consider...“Traffic is light” Nearly 1 of 2 deaths occur insingle-vehicle crashes, many whenno other vehicles are around.“Belts wrink
Key-in-ignition warning chime: Sounds when the key is left in theignition in the off or accessory position and the driver’s door is opened.Headlamps o
Note: If you are using MyKey™, the Belt-Minder威 cannot be disabled.Also, if the Belt-Minder威 has been previously disabled, it will bere-enabled during
• This will enable the Belt-Minder威 feature for that seating position if itis currently disabled. As confirmation, the safety belt warning light willf
Important supplemental restraint system precautionsAirbags DO NOT inflate slowly orgently and the risk of injury from adeploying airbag is greatest cl
WARNING: Do not put anything on or over the airbag module.Placing objects on or over the airbag inflation area may causethose objects to be propelled
How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suffic
WARNING: If the air bag has deployed, the air bag will notfunction again and must be replaced immediately. If the airbag is not replaced, the unrepair
• the system determines that an infant is present in a rear-facing infantseat that is installed according to the manufacturer’s instructions,• the sys
• When the front passenger sensing system enables the front passengerfrontal airbag (may inflate), the indicator will be unlit and stay unlit.If a per
WARNING: Sitting improperly out of position or with the seatback reclined too far can take off weight from the seat cushionand affect the decision of
WARNING: To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a chi
WARNING: Never remove the coolant reservoir cap while theengine is running or hot.Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel
WARNING: Any alteration/modification to the front passengerseat may affect the performance of the front passenger sensingsystem.Determining if the sys
WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. Contact your authorize
The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of
WARNING: Do not attempt to service, repair, or modify theSafety Canopy威 system, its fuses, the A, B, or C pillar trim, orthe headliner on a vehicle co
• Two crash sensors mounted on the B pillar (one on each side of thevehicle).• Two crash sensors located at the C pillar behind the rear doors (oneon
WARNING: If the SafetyCanopy威 system hasdeployed, the Safety Canopy威 willnot function again unless replaced.The Safety Canopy威 system(including the A,
The SOS Post-Crash Alert can be turned off when any one of thefollowing actions are taken by the driver or any other person:• pressing the hazard cont
Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb
Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe
WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli
MESSAGE CENTERYour vehicle’s message center allows you to configure/personalize certainvehicle options to suit your needs.The message center is also c
restrained properly, then restrain the child in the child safety seat orwith the belt-positioning booster. Remember that child seats andbelt-positioni
When installing a child safety seat with combination lap/shoulder belts:• Use the correct safety belt buckle for that seating position.• Insert the be
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out.6. All
10. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the
Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol.The LATCH anchors are locat
WARNING: Never attach two child safety seats to the sameanchor. In a crash, one anchor may not be strong enough to holdtwo child safety seat attachmen
Attaching child safety seats with tether strapsMany forward-facing child safety seats include a tether strap whichextends from the back of the child s
3. Open the tether anchor cover.4. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safety seat maynot
both the lap and shoulder belt on children who have outgrown childsafety seats, Ford Motor Company recommends use of a belt-positioningbooster.Booster
Locks and Security 109Keys 109Locks 111Anti-theft system 129Seating and Safety Restraints 140Seating 140Safety restraints 158Airbags 171Child restrain
If you calculate your average fuel economy by dividing distance traveledby gallons of fuel used (liters of fuel used by 100 kilometers traveled),your
Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli
WARNING: The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydro
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
WARNING: Under-inflation is the most common cause of tirefailures and may result in severe tire cracking, tread separationor ⬙blowout⬙, with unexpecte
Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo
Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
System check and vehicle feature customizationPress the SETUP button repeatedlyto cycle the message center throughthe following features:RESET FOR SYS
WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w
• Do not run over curbs or hit the tire against a curb when parkingWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the
• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/All Wheel Drive (AWD)vehicles (
Sometimes irregular tire wear can be corrected by rotating the tires.Note: If your tires show uneven wear ask an authorized dealer to checkfor and cor
3. 65: Indicates the aspect ratio which gives the tire’s ratio of height towidth.4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or ri
8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n
13. Maximum Permissible Inflation Pressure: Indicates the tiremanufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including inter
3. Once “OIL LIFE SET TO XXX%” is displayed, release and press theRESET button to change the Oil Life Start Value. Each release and presswill reduce t
When your temporary spare tire is installedWhen one of your road tires needs to be replaced with the temporaryspare, the TPMS system will continue to
Low TirePressureWarning LightPossiblecauseCustomer Action RequiredFlashingWarning LightSpare tire inuseYour temporary spare tire is in use.Repair the
SNOW TIRES AND CHAINSWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel
SUMMER TIRESYour Taurus SHO may be equipped with summer tires to providesuperior performance on wet and dry roads. Summer tires do not havethe Mud and
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei
• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle.3. Subtract the combined weight of the driver and pas
Press RESET to turn the warning chime on or off. The system will revertto chime on each time the vehicle is started. The heads up display and/orchime
1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now youhave the load capacity to transport the cement and your friend home.In metric units,
If you use a rental trailer, follow the instructions that the rental agencygives to you.Do not attach safety chains to the bumper.Trailer brakesElectr
• It is recommended to select the L (Low) gear position when additionalengine braking is needed. In situations such as prolonged downhilldriving on st
Front Wheel Drive (FWD) vehicles:Tow your Front Wheel Drive vehicle with all four wheels on the groundor with the front wheels off the ground by using
STARTINGPositions of the ignition (if equipped)If your vehicle is equipped with a push button start system, refer toPush button start system in this s
WARNING: Do not start your vehicle in a closed garage or inother enclosed areas. Exhaust fumes can be toxic. Always openthe garage door before you sta
• Make sure the gearshift lever is inP (Park).3. Turn the key to 3 (on) withoutturning the key to 4 (start).If your vehicle is equipped with apush but
3. After idling for a few seconds, release the parking brake, apply thebrake, shift into gear and drive.Note: If the engine does not start on the firs
vehicle from the on mode. If you would like to start the vehicle and youare in on mode, you must first switch the vehicle off.4. Start — press the STA
the message center. You can re-start the vehicle (by applying the brakepedal and pressing the START/STOP button) for up to 20 seconds, eventhough the
System warningsSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems.In the event of a multiple warning si
ENGINE BLOCK HEATER (IF EQUIPPED)An engine block heater warms the engine coolant which aids in startingand allows the heater/defroster system to respo
• Be sure that areas where the vehicle is parked are clean and clear ofall combustibles such as petroleum products, dust, rags, paper andsimilar items
Four-wheel anti-lock brake system (ABS)Your vehicle is equipped with an Anti-lock Braking System (ABS). Thissystem helps you maintain steering control
Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th
ADVANCETRAC姞 STABILITY ENHANCEMENT SYSTEMWARNING: Vehicle modifications involving braking system,aftermarket roof racks, suspension, steering system,
The AdvanceTrac威 system automatically enables each time the engine isstarted. All features of the AdvanceTrac威 system (TCS and ESC) areactive and moni
Excessive wheel spin is controlled in two ways, which may workseparately or in tandem, Engine Traction Control and Brake TractionControl. Engine Tract
Switching Off AdvanceTrac威If the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off certain features of the AdvanceTr
AdvanceTrac威 FeaturesControlswitchfunctionsMode“Slidingcar off”iconMessageCenterDisplay (ifequipped)ESCTractionControlControlswitchpressed andheld for
The EPS system has diagnostic checks that continuously monitor theEPS system to ensure proper operation. When a system error isdetected, the following
CHECK PARK AID (if equipped) — Displayed when the transmissionis in R (Reverse) and the reverse sensing system (park aid) is disabled.Refer to Rear pa
• Do not fill the power steering pump reservoir above the MAX mark onthe reservoir, as this may result in leaks from the reservoir.If the steering wan
See your authorized dealer as soon as possible if this procedureis used.WARNING: Do not drive your vehicle until you verify that thebrakelamps are wor
P (Park)This position locks the transmissionand prevents the front wheels fromturning.To put your vehicle in gear:• Press the brake pedal• Move the ge
D (Drive) with Grade AssistPressing the transmission controlswitch on the side of the gearshiftlever activates Grade Assist.Grade Assist• Improves dri
Understanding the gearshift positions of the 6–speed automatictransmission with SelectShift Automatic™ transmission (SST)(if equipped)Your vehicle has
N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D
Recommended shift speedsUpshift according to the following chart:Upshifts when accelerating (recommended for best fueleconomy)Shift from:1 - 2 15 mph
WARNING: To help avoid personal injury, always use cautionwhen in R (Reverse) and when using the RSS.WARNING: This system is not designed to prevent c
allows the driver to turn the RSS on and off. To turn the RSS off, referto Message center in the Instrument cluster chapter for moreinformation.Keep t
Image delay if displayed through the rearview mirror:When shifting out of R (Reverse) and into any other gear, the image inthe rearview mirror will re
AWD OFF (if equipped) — Displayed when the AWD system has beenautomatically disabled to protect itself. This is caused by operating thevehicle with th
Night time and dark area useAt night time or in dark areas, the camera system relies on the reverselamp lighting to produce an image. Therefore it is
OperationThe radar sensor detects vehiclesahead that are moving in the samedirection as your vehicle.If the radar detects that yourvehicle is rapidly
WARNING: The collision warning system’s brake support canonly help reduce the speed at which a collision occurs if thedriver applies the vehicle’s bra
Note: If the system cannot be turned off in a MyKey™ equipped vehicle,refer to MyKey™ in the Locks and Security chapter for moreinformation.Note: If c
The BLIS威 and CTA has an yellowindicator (also referred to as thealert) located in the left and rightexterior mirrors. When the vehicle isstarted, the
BLIS威 detection limitations: Due to the nature of radar technology,there may be certain instances where vehicles entering and exiting theblind spot zo
The CTA system detects vehicles approaching up to 45 feet (14 meters)away (approximately the width of five parking spaces). Coveragedecreases when veh
CTA coverage also decreases when parking at shallow angles (refer tofigure for approximate zone coverage areas [sensor obstructed forvehicle on left])
the BLIS威 and/or the CTA is turned off, the message center displaysBLIND SPOT SYS OFF and/or CTA SYSTEM OFF. When the BLIS威and/or the CTA system is of
Once the blockage is removed, the system will require some driving timeand detection of at least two vehicle objects prior to resetting or thedriver c
INTKEY COULD NOT PROGRAM — Displayed when an attempt ismade to program a fifth integrated key to the remote key entry system.For more information on i
ability to anticipate wheel slip and transfer torque to the rear wheelsbefore slip occurs. The AWD system is active all the time and requires noinput
When driving at slow speeds off-highway under high outsidetemperatures, use L (Low) gear when possible. L (Low) gear operationwill maximize the engine
WARNING: Always set the parking brake fully and make surethe gearshift is latched in P (Park). Turn the ignition to the offposition and remove the key
When driving at slow speeds in deep sand under high outsidetemperatures, use L (Low) gear when possible. L (Low) gear operationwill maximize the engin
“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nationswilderness are
Driving on snow and iceNote: Excessive tire slippage can cause transmission damage.AWD vehicles have advantages over 2WD vehicles in snow and ice butc
Failure to maintain your vehicle properly may void the warranty, increaseyour repair cost, reduce vehicle performance and operational capabilitiesand
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
Canadian customers refer to your Customer Information Guidefor information on:• coverage period• exact fuel amounts• towing of your disabled vehicle•
Note: With extended use, the flasher may run down your battery.FUEL PUMP SHUT-OFFIn the event of a moderate to severe collision, this vehicle is equip
SHIFT TO PARK (if equipped) — Displayed when the start/stopbutton is pressed to shut off the engine with the shift select lever in anyposition other t
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
Passenger compartment fuse panelThe fuse panel is located under the instrument panel to the left of thesteering wheel.The fuses are coded as follows.F
Fuse/RelayLocationFuse AmpRatingProtected Circuits8 10A Low beam headlamps (right)9 15A Interior lights, Cargo lamps10 15A Switch illumination, Puddle
Fuse/RelayLocationFuse AmpRatingProtected Circuits29 5A Instrument panel cluster, Heads updisplay30 5A Not used (spare)31 10A Not used (spare)32 10A A
Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot
Fuse/RelayLocationFuse AmpRatingPower Circuits3 — Not used4 30A** Front wiper5 30A** Passenger seat6 20A** Cigar lighter7 — Not used8 30A** Moon roof9
Fuse/RelayLocationFuse AmpRatingPower Circuits31 — Not used32 30A** Driver seat33 30A** Passive entry/passive start(PEPS)34 — Not used35 40A** Front h
Fuse/RelayLocationFuse AmpRatingPower Circuits58 — Not used59 Half ISO relay Left halogen headlamp relay60 Half ISO relay Right halogen headlamp relay
Dissimilar spare tire/wheel informationWARNING: Failure to follow these guidelines could result in anincreased risk of loss of vehicle control, injury
3. Full-size dissimilar spare without label on wheelWhen driving with the full-size dissimilar spare tire/wheel, do not:• Exceed 70 mph (113 km/h)• Us
VEHICLE SPEED 80 MPH MAX — Displayed when a MyKey™ is inuse and the Admin has enabled the MyKey speed limit and the vehiclespeed is 80 mph (130 km/h).
Stopping and securing the vehicle1. Park on a level surface, set theparking brake and activate hazardflashers.2. Place gearshift lever in P (Park)and
WARNING: To help prevent the vehicle from moving when youchange a tire, be sure to place the transmission in P (Park), setthe parking brake and block
3. Put the jack in the jack notchnext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is completely off theground.Note: DO
Stowing the tire and jack1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown.
If you are stowing the flat tire:1. Remove the extension bolt fromthe exterior pocket of the felt bag.2. Install the jack as shown inStep 4 under Stow
1. Air compressor (inside)2. Diverter knob3. On/Off button4. Air pressure gauge5. Deflation button6. Sealant bottle/canister7. Sealant filling clear t
• Read the information in the Tips for use of the temporary mobilitykit section to ensure safe operation of the temporary mobility kit andyour vehicle
• Operating the temporary mobility kit could cause an electricaldisturbance in radio and DVD player operation.What to do when a tire is puncturedA tir
4. Plug the power cable into the 12Vpower point in the vehicle.5. Remove the warning sticker found on the canister and place it on thetop of the instr
tire pressure has to be checked with the compressor in the OFFposition to get the correct tire pressure reading.WARNING: Do not stand directly over th
Customer Assistance 311Reporting safety defects (U.S. only) 317Reporting safety defects (Canada only) 317Cleaning 318Maintenance and Specifications 32
AUDIO SYSTEMSNote: If your volume is muted and MYKEY VOLUME LIMITED isdisplayed, refer to MyKey™ in the Locks and Security chapter for moreinformation
4. Adjust the tire to therecommended inflation pressurefrom the tire label located on thedriver’s door or door jam area.Pressing the deflation button
Removal of the Sealant Canister from the Temporary Mobility Kit1. Unwrap the clear tube from thecompressor housing.2. Press the button located on thet
2. Once aligned, seat the sealantcanister by lightly pushing downuntil you hear an audible click.3. Wrap the clear tube around thecompressor housing.N
Bolt size Wheel lug nut torque*lb.ft. N•m1/2-20 UNF 100 135* Torque specifications are for nut and bolt threads free of dirt andrust. Use only Ford re
WARNING: Do not insert the nozzle of portable fuel containersor aftermarket funnels into the Easy Fuel™ system. This coulddamage the fuel system and i
Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
2. Start the engine of the disabled vehicle.3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disc
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
Setting the clockTo set the time, press CLOCK. Thedisplay will read SET TIME. Use thememory preset numbers (0–9) toenter in the desired time–hours and
If the vehicle is towed by other means or incorrectly, vehicledamage may occur.Ford Motor Company produces a towing manual for all authorized towtruck
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized
In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph
In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
If your vehicle must be serviced while you are traveling or living inCentral America, the Caribbean, or the Middle East, contact the nearestauthorized
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is
WAXING• Wash the vehicle first.• Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your aut
Saving presets automatically: Autoset allows you to set the strongestlocal radio stations without losing your original manually set presetstations for
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
3.5L V6 SHO ENGINEPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authori
• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32-A),available from your au
If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows:1. Wipe up spilled liqui
LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• For routine cleaning, wipe the surface wit
Motorcraft Premium Glass Cleaner (Canada only) (CXC-100)Motorcraft Premium Liquid Wax (ZC-53-A)Motorcraft Premium Windshield Washer Concentrate (U.S.
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column.2. Go to th
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.5L V6 engine1. Power steering fluid reservoir2. Engine coolant reservoir3. Brake fluid reservoir4. B
3.5L V6 SHO engine1. Engine coolant reservoir2. Brake fluid reservoir3. Battery4. Power distribution box5. Air filter assembly6. Automatic transmissio
LOAD:For a single CD system– Thiscontrol is not operational. To load aCD, simply insert the disc, label side up, into the CD slot.For a CD6 system– Pr
Engine shieldSome vehicles may be equippedwith an aero-shield under theengine. This shield needs to beremoved for service, including oiland filter cha
CHANGING THE WIPER BLADES1. Pull the wiper blade and armaway from the glass.2. Squeeze the locking tabs torelease the blade from the arm andpull the b
5. Locate and carefully remove theengine oil level dipstick.6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil l
• Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine isoverfilled, some oil must beremoved from the e
Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol con
For longer, trouble-free operation, keep the top of the battery clean anddry. Also, make certain the battery cables are always tightly fastened tothe
Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe bat
concentration should be maintained at 50/50 coolant and distilled water,which equates to a freeze point of -34°F (-36°C). Coolant concentrationtesting
Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservo
WARNING: To reduce the risk of personal injury, make sure theengine is cool before unscrewing the coolant pressure relief cap.The cooling system is un
SCAN: Press for a brief sampling ofall tracks on the current disc orMP3 folder.DIRECT:In CD mode– Press DIRECT. Thedisplay will read DIRECT TRACKMODE
Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut
What you should know about fail-safe coolingIf the engine coolant supply is depleted, this feature allows the vehicle tobe driven temporarily before i
WARNING: Never remove the coolant reservoir cap while theengine is running or hot. The hot coolant is under pressure andmay cause serious burns.5. Re-
• Automotive fuels can be harmful or fatal if swallowed. Fuel such asgasoline is highly toxic and if swallowed can cause death or permanentinjury. If
RefuelingWARNING: Fuel vapor burns violently and a fuel fire can causesevere injuries. To help avoid injuries to you and others:• Read and follow all
Note: A fuel spillage concern may occur if overfilling the fuel tank. Donot overfill the tank to the point that the fuel is able to bypass the fuelfil
Note: Use of any fuel other than those recommended may causepowertrain damage, a loss of vehicle performance, and repairs may notbe covered under warr
Running out of fuelAvoid running out of fuel because this situation may have an adverseeffect on powertrain components.If you have run out of fuel:• Y
1. After lifting the trunk cargocover, locate the white plasticfunnel. It is attached to the rear,lower edge of the spare tirecompartment.2. Slowly in
The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fu
TUNE: Turn to go to the next /previous available SIRIUS satellitestation.DIRECT: Press DIRECT then enterthe desired channel (i.e. 002) usingthe memory
Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fuelecon
• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled mainten
• Have the items listed in scheduled maintenance informationperformed according to the specified schedule.The scheduled maintenance items listed in sc
government emission standards. The OBD-II system also assists yourauthorized dealer in properly servicing your vehicle. When the serviceengine soonind
indicate that the vehicle is not ready for I/M testing. To determine if thevehicle is ready for I/M testing, turn the ignition key to the on positionf
BRAKE FLUIDThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX
6. Install the dipstick making sure it is fully seated in the filler tube.7. Remove the dipstick and inspect the fluid level. The fluid should be inth
If an overfill occurs, excess fluidshould be removed by an authorizeddealer.An overfill condition oftransmission fluid may cause shift and/or engageme
Changing the air filter element3.5L V63.5L V6 (SHO)1. Release the clamps that secure the air filter housing cover.2. Carefully separate the two halves
6. Replace the air filter housingcover and secure the clamps. Besure that the air cleaner cover tabsare engaged into the slots of the aircleaner housi
CAT (Category) / FOLD(Folder): Press to toggle betweenturning the most recently selectedsatellite radio category on or off. The category icon (CAT) wi
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItems CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationBrake fluidBetween MAX a
Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine oil 5.5 quarts (5.2L)•Motorcraft SAE 5W-20Premium SyntheticBlend M
Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationFuel tank19.0 gallons(71.9 L)——1Approximate dry fill capacity. Actual amo
ENGINE DATAEngine 3.5L V6 engine 3.5L V6 SHO engineCubic inches 214 214FuelSee Octanerecommendationsearlier in this chapter.See Octanerecommendations
3.5L V6 SHO engineIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requireth
Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX
TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
Peace of mindRemote startVehicle security systemsWheel locksFor maximum vehicle performance, keep the following information inmind when adding accesso
FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on
OK. The song will appear in the display for confirmation. Press OKagain and the display will read SONG DELETED. If you do not wantto delete the curren
Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With
Ford Extended Service Plan3712010 Taurus (500)Owners Guide (own2002), 1st PrintingUSA (fus)
AAccessory delay ...82Adaptive Cruise Control ...86AdvanceTrac ...244AdvanceTrac Sport Mod
Cargo net ...108CD ...30Cell phone use ...8Cha
Emergencies, roadsidejump-starting ...304running out of fuel ...303, 347Emission control system ...351Engine ...
Hood ...327IIgnition ...234, 363Illuminated visor mirror ...75Infant seat
Motorcraft parts ...324, 359Multi-contour seats ...144MyKey ...134NNavigation system
Occupant ClassificationSensor ...159warning light and chime ...166Safety restraints - LATCHanchors ...
Transmission ...251brake-shift interlock (BSI) ...250fluid, checking and adding(automatic) ...355
d. RESET PIN: Press OK when RESET PIN is displayed. The displaywill read ARE YOUR SURE. Press OK again to automatically reset thePIN number to its ini
/ Play/Pause: Press thiscontrol to play or pause the currentCD.OK: Your vehicle may be equippedwith special phone and mediafeatures which will require
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
Required equipment:1. Any portable music player designed to be used with headphones2. An audio extension cable with stereo male 1/8 in. (3.5 mm)connec
5. For safety reasons, connecting or adjusting the settings on yourportable music player should not be attempted while the vehicle ismoving. Also, the
Radio reception factors:There are three factors that can affect radio reception:• Distance/strength: The further you travel from an FM station, thewea
Do not use any irregular shapedCDs or discs with a scratchprotection film attached.CDs with homemade paper(adhesive) labels should not beinserted into
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio forthe selectedchannel.No action required. Thisme
Radio Display Condition Action RequiredNO TEXT Categoryinformation notavailable.Category information notavailable at this time onthis channel. The sys
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the
4. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. A/Cengages automaticall
Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti
• To improve the A/C cool down, drive with the windows slightly openfor 2-3 minutes after start up or until the vehicle has been “aired out.”During ex
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the In
4. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. A/Cengages automaticall
12. Power/Driver temperature: Press to activate/deactivate theclimate control system. When the system is off, outside air is preventedfrom entering th
Temperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the Instrument Cluster chapter.1. CLIMATE: Press to contro
10. Driver temperature: Press to increase/decrease the air temperaturefor the driver side of the vehicle. This control also adjusts the passengerside
• : Distributes air through the floor vents, rear seat floor vents.• : Distributes air through the windshield defroster vents, de-mistervents, floor v
For maximum cooling performance:• Automatic operation:1. Press AUTO for full automatic operation.2. Do not override A/C or(recirculated air).3. Set th
CABIN AIR FILTERThe cabin air filter element is designed to reduce the concentration ofairborne particles such as dust, spores and pollen in the air b
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the low beam headlampso
Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance
3. Turn the ignition switch to on and then back to off.4. Turn the headlamp control to the autolamp position. The headlampswill turn on.5. Wait the de
Operation - The high beam switch can be used to turn the high beamson. They will then remain on until the switch has been returned to theneutral posit
• The vehicle speed falls below 27 mph (43 km/h).• The ambient light level is high enough that high beams are notneeded.• Severe rain, snow or fog is
For significant blockages (e.g. bird dropping, bug splatter, snow, or ice),the automatic high beam system uses a blocked sensor computerprogram. If it
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicablelit components in the vehicle duringheadlamp and parking lam
3. Turn on the low beam headlamps to illuminate the wall or screen andopen the hood.To see a clearer light pattern for adjusting, you may want to bloc
INTERIOR LAMPSDome lamps and map lampsThe map lamps are located on theoverhead console. Press the controlson either side of each map lamp toturn on th
BULB REPLACEMENTLamp assembly condensationExterior lamps are vented to accommodate normal changes in pressure.Condensation can be a natural by-product
Function Number of bulbsTradenumberLow series headlamps(high/low beam)2 HB3*High series headlamps(high/low beam) (HID)2—Front park/turn lamp 23457NAK(
3. Remove the outboard rubber bootfrom the lamp assembly by pullingrearward.4. Remove the bulb socket byturning it counterclockwise andpulling it stra
Event Data RecordingOther modules in your vehicle — event data recorders — arecapable of collecting and storing data during a crash or nearcrash event
Replacing rear brake/tail/turn and side marker lamp bulbsThe brake/tail/turn and side marker lamp bulbs are located in the taillamp assembly. Follow t
Replacing backup lamp bulbsThe backup lamp bulbs are located in the deck lid assembly.1. Make sure the headlamp switch is in the off position.2. Remov
Replacing high-mount brake lamp bulbsYour vehicle is equipped with an LED high-mount brake lamp. It isdesigned to last the life of the vehicle. If rep
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
Courtesy wipe feature: One extra wipe will occur a few seconds afterwashing the front window to clear any excess washer fluid remaining onthe windshie
ILLUMINATED VISOR MIRRORLift the mirror cover to turn on thevisor mirror lamp.Slide on rod featureThe visor will slide back and forthon the rod for in
ELECTRONIC COMPASS (IF EQUIPPED)The compass heading is displayed in the center stack display.The compass reading may be affected when you drive near l
4. Press and release the 7 and 9radio preset buttons together,repeatedly until ZONE XX changesto the correct zone (1–15) in theCID.5. The direction wi
CENTER CONSOLEYour vehicle may be equipped with a variety of console features. Note:The appearance and features of the center console may be different
AUXILIARY POWER POINT (12VDC)Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will damag
information”) only to help provide you with the directions, trafficreports, or business searches you request. If you do not wantFord or its vendors to
Press and pull the window switchesto open and close windows.• Push down (to the first detent)and hold the switch to open.• Pull up (to the first deten
Driver’s and passenger’s windowone-touch up or down (ifequipped)To operate one touch-down:• Press the switch completely downto the second detent and r
and the window will travel up with no bounce-back or pinchprotection. If the switch is released before the window is fully closed,the window will stop
Automatic dimming interior rear view mirror (if equipped)Your vehicle may be equipped with an interior rear view mirror that hasan auto-dimming functi
Blind spot mirrors (if equipped)Your vehicle may be equipped with blind spot information mirrors. SeeBlind Spot Information System威 (BLIS威) with Cross
WARNING: Do not use the speed control in heavy traffic or onroads that are winding, slippery or unpaved.Using speed controlThe speed controls are loca
Increasing speed while using speed controlTo set a higher speed:• Press and hold SET + until you get to the desired speed, then release.You can also u
WARNING: Always pay close attention to changing roadconditions, especially when using Adaptive Cruise Control.Adaptive Cruise Control cannot replace a
3. Press and release the SET +control. The vehicle speed will bestored in the memory and themessage center will display SETXXX MPH (your desired speed
braking which is applied by the ACC system is limited and can beoverridden by the driver applying the brakes.If the ACC system predicts that itsmaximu
EXPORT UNIQUE (NON–UNITED STATES/CANADA) VEHICLESPECIFIC INFORMATIONFor your particular global region, your vehicle may be equipped withfeatures and o
Note: It is the driver’s responsibility to select a gap appropriate to thedriving conditions.Disengaging adaptive cruise controlPress the brake pedal
Resuming the set speedPress and release the RESUMEcontrol. This will automaticallyreturn the vehicle to the previouslyset speed. The set speed will di
Turning off cruise controlPress the OFF button to turn off thecruise control.Note: When you turn off the cruisecontrol or the ignition, your cruisecon
• There may be issues with the detection of vehicles in front whendriving into and coming out of a bend or curve in the road.In these cases ACC may br
Cause ActionThe surface of the radar in thegrille is dirty or obstructed insome wayClean the grille surface in front ofthe radar or remove the objectc
STEERING WHEEL CONTROLS (IF EQUIPPED)Radio control featuresVOL + (Volume): Press to increasethe volume.VOL – (Volume): Press to decreasethe volume.(Se
SYNC威 system hands freecontrol feature (if equipped)Press briefly to use the voicecommand feature. You will hear atone and LISTENING will appear inthe
To open the moon roof: Press andrelease the SLIDE control, the moonroof will open automatically. Pressthe switch again to stop the moonroof.WARNING: W
HomeLink威Car2U威 Home AutomationSystemHomeLink姞 Wireless Control System (if equipped)The HomeLink威 Wireless ControlSystem, located on the driver’s viso
Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink威 equipped vehiclepurchase). I
Commentaires sur ces manuels