Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Message center 20Entertainment Systems 32Auxiliary input jack (Line in) 41USB
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
Note: Replacement of the battery will not cause the IKT to becomedeprogrammed from your vehicle. The IKT should operate normally afterbattery replacem
Battery saverThe battery saver will shut off the interior lamps 10 minutes after theignition has been turned to the off position and a door is left op
Anti-theft indicatorThe anti-theft indicator is located in the instrument cluster.• When the ignition is in the offposition, the indicator will flasho
programmed to your vehicle; only four of these eight keys can be IKTswith remote entry functionality.If your IKTs or standard SecuriLock威 coded keys a
4. After three seconds but within 10 seconds of turning the ignition tothe 1 (off) position, insert the second previously coded key into theignition.5
• Change in vehicle inclinationNote: The active anti-theft system includes a motion detection systemwhich monitors the passenger cabin and a vehicle i
There is a 20 second countdown when any of the above actions occurbefore the vehicle becomes armed.Each door, the hood or the trunk is armed individua
SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o
To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o
To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting the manual seats (if equippe
Four-way seat adjust (driver side only)Pump the handle upwards to raisethe cushion and pump downward tolower the cushion to the desiredlocation.Using
WARNING: Sitting improperly out of position or with the seatback reclined too far can take off weight from the seat cushionand affect the decision of
Move the switch in the direction ofthe arrows to raise or lower the rearportion of the seat cushion.Press the switch in the direction ofthe arrows to
To operate the heated seats:• Press control to activate.• Press again to deactivate.The heated seats will only function when the engine is running.Rea
To lower the seatback(s) frominside the vehicle, be sure the headrestraint is in the upright position,pull the strap to release theseatback and then f
• Restraints Control Module (RCM) with impact and safing sensors.• Restraint system warning light and back-up tone.• The electrical wiring for the air
Front passenger sensing systemFor airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occu
Front safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly ag
WARNING: To reduce the risk of injury, make sure children sitin a rear seating position where they can be properly restrained.WARNING: Never let a pas
WARNING LIGHTS AND CHIMESBase instrument cluster (V6 shown; V8 similar)Optional instrument cluster (V6 shown; V8 similar)Warning lights and gauges can
WARNING: Front and rear seat occupants, including pregnantwomen, should wear safety belts for optimum protection in anaccident.Combination lap and sho
2. To unfasten, press the releasebutton and remove the tongue fromthe buckle.WARNING: The center of the rear seat is NOT designed as aseating position
WARNING: Failure to replace the Belt and Retractor assemblycould increase the risk of injury in collisions.The front and rear safety restraints in the
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
Safety belt pretensionerYour vehicle is equipped with safety belt pretensioners at the driver andfront outboard passenger seating positions.The safety
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war
If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the onposition or less than1-2 minutes h
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra
WARNING: Do not sit on top of a buckled safety belt or insert alatchplate into the buckle to avoid the Belt-Minder威 chime. Todo so may adversely affec
1. Turn the ignition switch to the on position. DO NOT START THEENGINE.2. Wait until the safety belt warning light turns off (approximately oneminute)
Service engine soon: The serviceengine soon indicator lightilluminates when the ignition is firstturned to the on position to checkthe bulb and to ind
Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in
WARNING: Do not attempt to service, repair, or modify theairbag supplemental restraint systems or its fuses. Contact yourauthorized dealer as soon as
How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustains alongitudinal deceleration suff
• one or more impact and safing sensors• a readiness light and tone• a diagnostic module• and the electrical wiring which connects the components• fro
• the system determines that a small child is present in a forward-facingchild restraint that is installed according to the manufacturer’sinstructions
• Turn the vehicle off and ask the person to place the seatback in thefull upright position.• Have the person sit upright in the seat, centered on the
passenger seat, the passenger airbag will be disabled. Even though thepassenger airbag is disabled, the ⬙pass airbag off⬙ lamp may or may notbe illumi
In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi
WARNING: Do not use accessory seat covers. The use ofaccessory seat covers may prevent the deployment of the sideairbags and increase the risk of inju
The side airbags are fitted on the outboard side of the seatbacks of thefront seats. In certain lateral collisions, the airbag on the side affected by
time, contact your authorized dealer as soon as possible. Illuminationafter releasing the parking brake indicates low brake fluid level. Contactyour a
A difficulty with the system is indicated by one or more of the following:• The readiness light will eitherflash or stay lit.• The readiness light wil
Important child restraint precautionsWARNING: Always make sure your child is secured properly ina device that is appropriate for their height, age and
Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb
Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe
WARNING: Always carefully follow the instructions andwarnings provided by the manufacturer of any child restraint todetermine if the restraint device
training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertifi
Airbags can kill or injure a child in a child seat. NEVER place arear-facing child seat in front of an active airbag. If you must use aforward-facing
1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
towards the buckle will additionally help to remove remaining slack fromthe belt.9. Attach the tether strap (if the child seat is equipped). Refer toA
Engine oil pressure (ifequipped): Illuminates when the oilpressure falls below the normalrange, refer to Engine oil in theMaintenance and Specificatio
Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol.The LATCH anchors are locat
Each time you use the safety seat, check that the seat is properlyattached to the lower anchors and tether anchor, if applicable. Tug thechild seat fr
The tether strap anchors in your vehicle are in the following positions(shown from top view):Attach the tether strap only to theappropriate tether anc
3. Open the tether anchor cover.4. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safety seat maynot
The tether anchors on theconvertible are located rearward ofthe seatback in the convertible topsling.Note: For easier access, attach thetether with th
2. Access tether anchors locatedbehind the seatback under the vinyltag marked with the child tetheranchor symbol.3. Clip the tether strap to theanchor
Child booster seatsThe belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child
Booster seats should be used until you can answer YES to ALL of thesequestions when seated without a booster seat:• Can the child sit all the way back
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
The importance of shoulder beltsUsing a booster without a shoulder belt increases the risk of a child’shead hitting a hard surface in a collision. For
O/D OFF (automatictransmission): Illuminates whenthe overdrive function of thetransmission has been turned off;refer to the Driving chapter. If the li
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli
WARNING: The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydro
• Extra load: A class of P-metric or Metric tires designed to carry aheavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires].Increasing the
WARNING: Under-inflation is the most common cause of tirefailures and may result in severe tire cracking, tread separationor ⬙blowout⬙, with unexpecte
Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo
Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w
• Do not run over curbs or hit the tire against a curb when parkingWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the
• Rear-wheel drive (RWD)vehicles/Four-wheel drive(4WD)/All-wheel drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can b
Headlamps on warning chime: Sounds when the headlamps or parkinglamps are on, the ignition is off (the key is not in the ignition) and thedriver’s doo
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including inter
To restore the full functionality of the Tire Pressure Monitoring System,have the damaged road wheel/tire repaired and remounted on yourvehicle. For a
Low Tire PressureWarning LightPossiblecauseCustomer Action RequiredFlashing WarningLightSpare tire inuseYour temporary spare tire is inuse. Repair the
SNOW TIRES AND CHAINSWARNING: Driving too fast for conditions creates the possibilityof loss of vehicle control. Driving at very high speeds forextend
Speedometer: Indicates the current vehicle speed.• V6 instrument cluster• V8 instrument clusterEngine coolant temperaturegauge: Indicates engine coola
SUMMER TIRESYour Ford vehicle may be equipped with summer tires to providesuperior performance on wet and dry roads. Summer tires do not havethe Mud a
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
Steps for determining the correct load limit:1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.
calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 -540 = -103 kg. You will need to reduce the load weight by at least240 lb. (104
Safety chainsAlways connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cr
eliminate excessive downshifting and upshifting for optimum fueleconomy and transmission cooling.• Anticipate stops and brake gradually.Servicing afte
Trip odometer: Registers the distance of individual journeys.• Base instrument cluster:Press the reset button to select TripA and Trip B. Press and ho
STARTINGPositions of the ignition1. Off — locks the automatictransmission gearshift lever andallows key removal.Note: The ignition key cannot beremove
WARNING: Do not start your vehicle in a closed garage or inother enclosed areas. Exhaust fumes can be toxic. Always openthe garage door before you sta
• Make sure the parking brake isset.If starting a vehicle with a manual transmission:• Make sure the parking brake isset.• Push the clutch pedal to th
Starting the engine1. Turn the key to 3 (on) withoutturning the key to 4 (start). If thereis difficulty in turning the key,rotate the steering wheel u
WARNING: Failure to follow engine block heater instructionscould result in property damage or physical injury.WARNING: To reduce the risk of electrica
• Finally, have the engine block heater system checked during your falltune-up to be sure it’s in good working order.How to use the engine block heate
ABS warning lampThe ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringsta
WARNING: Always set the parking brake fully and make surethat the gearshift is securely latched in P (Park) (automatictransmission) or in 1 (First) (m
WARNING: If a failure has been detected within theAdvanceTrac威 system, the stability control light and the stabilitycontrol off light will illuminate
• The brake pedal may feel stiffer than usual.Traction control system (TCS)Traction control is a driver aid feature that helps your vehicle maintaintr
Seating and Safety Restraints 107Seating 107Safety restraints 115Airbags 129Child restraints 140Tires, Wheels and Loading 160Tire information 160Tire
Engine oil pressure gauge (ifequipped): Indicates engine oilpressure. The needle should stay inthe normal operating range(between “L” and “H”). If the
• Maneuvering quickly to avoid an accident, pedestrian or obstacle• Driving over a patch of ice or other slippery surfaces• Changing lanes on a snow-r
AdvanceTrac威 FeaturesControlswitch func-tionsMode“Slidingcar off”iconMessageCenterDisplay (ifequipped)ESC TCSDefault atstart-upTurns onduringbulbcheck
Sport mode is not intended for use on public roadways as this modeprovides less AdvanceTrac威 system intervention than when the defaultESC and traction
BRAKE-SHIFT INTERLOCKThis vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) whe
WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. Contact your au
R (Reverse)With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Re
3 (Third)This position allows for third gear only.• Provides engine braking.• To return to D (Drive) without Overdrive, move the transmission shiftlev
MANUAL TRANSMISSION OPERATION (IF EQUIPPED)Using the clutchManual transmission vehicles have a starter interlock that preventscranking the engine unle
Recommended shift speedsDo not downshift into 1 (First) when your vehicle is movingfaster than 15 mph (24 km/h). This will damage the clutch.Upshift a
REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rearview camera system,located on the trunk, provides avideo image which appears in therearview mirror or on t
Autolamp delay (if equipped)This feature keeps your headlights on for up to three minutes after theignition is switched off.1. To disable/enable the a
The camera lens for the camera is located on the trunk. Keep the lensclean so that the video image remains clear and undistorted. Clean thelens with a
DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co
FUEL PUMP SHUT-OFF SWITCHFUELRESETThis device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Driver rear window (convertible only)2 15A Brake On/Off (BOO) p
Fuse/RelayLocationFuse AmpRatingProtected Circuits11 10A Security module12 7.5A Power mirrors13 5A Not used (Spare)14 10A Center information display,
Fuse/RelayLocationFuse AmpRatingProtected Circuits39 20A Radio/Navigation40 20A Not used (Spare)41 15A Accessory delay (windows, automaticdimming rear
If the battery has been disconnected and reconnected, refer to theBattery section of the Maintenance and Specifications chapter.The high-current fuses
Selectable featuresResetPress this control to select and resetfunctions shown in the INFO menuand SETUP menu.Setup menuPress this control for the foll
Fuse/RelayLocationFuse AmpRatingProtected Circuits14 15A** Fuel pump relay #2 (Shelby only)15 10A** Intercooler pump relay(Shelby only)16 20A** Heated
Fuse/RelayLocationFuse AmpRatingProtected Circuits40 15A** PCM Vehicle Power4–ignitioncoil41 G8VA relay Fuel pump relay42 G8VA relay Intercooler pump
CHANGING THE TIRESIf you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel
A dissimilar spare tire/wheel is defined as a spare tire and/or wheel thatis different in brand, size or appearance from the road tires and wheelsand
The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following:• Handling, stability and braking performance• Comfort and
WARNING: If the vehicle slips off the jack, you or someone elsecould be seriously injured.WARNING: Do not attempt to change a tire on the side of thev
3. Remove the center ornament (ifequipped) from the wheel. Looseneach wheel lug nut one-half turncounterclockwise but do not removethem until the whee
7. Lower the wheel by turning the jack handle counterclockwise.8. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug
1. Air compressor (inside)2. Diverter knob3. On/Off button4. Air pressure gauge5. Sealant bottle/canister6. Sealant filling clear tube7. Sealant tube
• Read the information in the Tips for use of the temporary mobilitykit section to ensure safe operation of the temporary mobility kit andyour vehicle
The sequence of the system check report and how it appears in themessage center is as follows:1. OIL LIFE2. CHARGING SYSTEM3. ALL DOORS CLOSED4. DRIVE
• Operating the temporary mobility kit could cause an electricaldisturbance in radio and DVD player operation.What to do when a tire is puncturedA tir
4. Plug the power cable into the 12Vpower point in the vehicle.5. Remove the warning sticker found on the canister and place it on thetop of the instr
tire pressure has to be checked with the compressor in the OFFposition to get the correct tire pressure reading.WARNING: Do not stand directly over th
4. Adjust the tire to therecommended inflation pressurefrom the tire label located on thedriver’s door or door jam area.Note: The tire pressure has to
Removal of the sealant canister from the temporary mobility kit1. Unwrap the clear tube from thecompressor housing.2. Locate the yellow cap at the end
Installation of the sealant canister to the temporary mobility kit1. Align the sealant canister withthe temporary mobility kit housing.2. Once aligned
Be sure to check the sealantcompound’s “use by” date regularly.The “use by” date is on the lowerright hand corner of the labellocated on the sealant c
RUNNING OUT OF FUELIf you have run out of fuel and need to refill the vehicle with a portablefuel container, see Running out of fuel in the Maintenanc
3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake onboth vehicles
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
Halo lightTurns the halo lighting around the gauges on or off.1. To turn the halo lighting on oroff, select this function from theSETUP MENU.2. Press
2. Start the engine of the disabled vehicle.3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disc
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
Emergency towingIn case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport veh
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized
In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph
In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext
procedure outlined on the first page of the Customer Assistance section,you may be eligible to participate in the BBB AUTO LINE program.The BBB AUTO L
The CAMVAP program is a straight forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have
If you are in another foreign country, contact the nearest authorizeddealer. If the authorized dealer employees cannot help you, they candirect you to
Note: Headlamps or parklamps must be on to set up colors.To choose colors for the gauges, halo color or ambient lighting do thefollowing:1. Press SETU
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i
WAXING• Wash the vehicle first.• Do not use waxes that contain abrasives; use Motorcraft威 PremiumLiquid Wax (ZC-53-A), which is available from your au
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
4.6L 3V V8 ENGINEPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authoriz
Cleaner (ZC-23) in the U.S., or Premium Quality Windshield WasherFluid [CXC-37-(A, B, D, or F)] in Canada, available from yourauthorized dealer.• The
• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to a
WARNING: Do not use cleaning solvents, bleach or dye on thevehicle’s safety belts, as these actions may weaken the beltwebbing.WARNING: On vehicles eq
FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
Units (English/Metric)1. Select this function from theSETUP menu for the current unitsto be displayed.2. Press RESET to change fromEnglish to Metric.A
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located on thedriver’s side kick panel.2. Go to the front of the vehicle and releas
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.0L V6 engine1. Battery2. Engine oil filler cap3. Engine oil dipstick4. Brake fluid reservoir5. Air f
4.6L 3V V8 engine1. Battery2. Engine oil filler cap3. Engine oil dipstick4. Brake fluid reservoir5. Air filter assembly6. Power steering fluid reservo
Engine shieldSome vehicles may be equippedwith an aero-shield under theengine. This shield needs to beremoved for service, including oiland filter cha
CHANGING THE WIPER BLADES1. Pull the wiper blade and armaway from the glass.2. Squeeze the locking tabs torelease the blade from the arm andpull the b
5. Locate and carefully remove the engine oil level dipstick.• 4.0L V6 engine• 4.6L V8 engine6. Wipe the dipstick clean. Insert the dipstick fully, th
• If the oil level is below the lower hole, add enough oil to raise thelevel within the lower and upper holes.• 4.0L V6 engine• 4.6L V8 engine• Oil le
Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t
Do not use supplemental engine oil additives, cleaners or other enginetreatments. They are unnecessary and could lead to engine damage thatis not cove
Change your engine oil according to the appropriate schedule listed inthe scheduled maintenance information.Ford production and Motorcraft威 replacemen
Language1. Select this function from theSETUP menu for the currentlanguage to be displayed.2. Waiting four seconds or pressingthe RESET control cycles
WARNING: When lifting a plastic-cased battery, excessivepressure on the end walls could cause acid to flow through thevent caps, resulting in personal
transmission may shift firmly. This operation is considered normal andwill not affect function or durability of the transmission. Over time theadaptiv
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the FULL COLD level or within theCOLD
WARNING: Do not put engine coolant in the windshield washerfluid container. If sprayed on the windshield, engine coolantcould make it difficult to see
Add the proper mixture of coolant and water to the cooling system byfollowing these steps:1. Before you begin, turn the engine off and let it cool.2.
Fill your engine coolant reservoir as outlined in Adding engine coolantin this section.Severe climatesIf you drive in extremely cold climates (less th
• The engine coolant temperature indicator will illuminate.• The service engine soon indicator light will illuminate.If the engine reaches a preset ov
5. Restart the engine and take your vehicle to an authorized dealer.Driving the vehicle without repairing the engine problemincreases the chance of en
swallowed can cause death or permanent injury. If fuel is swallowed,call a physician immediately, even if no symptoms are immediatelyapparent. The tox
RefuelingWARNING: Fuel vapor burns violently and a fuel fire can causesevere injuries. To help avoid injuries to you and others:• Read and follow all
The DTE function will display LOW FUEL LEVEL when you haveapproximately 50 miles (80 km), to empty. If you reset this warningmessage, it will return a
Note: A fuel spillage concern may occur if overfilling the fuel tank. Donot overfill the tank to the point that the fuel is able to bypass the fuelfil
Your vehicle was not designed to use fuel or fuel additives with metalliccompounds, including manganese-based additives.Note: Use of any fuel other th
performance and emission control system protection for your vehicle.Gasolines that meet the World-Wide Fuel Charter should be used whenavailable. Ask
1. Locate the white plastic funnel. Itis included with the tire changingtools. (For vehicles equipped withthe temporary mobility kit, thefunnel is loc
The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fue
Driving style — good driving and fuel economy habitsGive consideration to the lists that follow and you may be able to changea number of variables and
• Carrying unnecessary weight may reduce fuel economy (approximately1 mpg [0.4 km/L] is lost for every 400 lb [180 kg] of weight carried).• Adding cer
emission control, such non-Ford parts should be equivalent to genuineFord Motor Company parts in performance and durability.WARNING: Do not park, idle
3. The fuel fill inlet may not have been properly closed. See Easy Fuel™“no cap” fuel system in this chapter.4. Driving through deep water—the electri
vehicle is not ready for I/M testing, the following driving cycle consistingof mixed city and highway driving may be performed:15 minutes of steady dr
Instantaneous fuel economy (IFE)Select this function from the INFOmenu to display your instantaneousfuel economy. This will display yourfuel economy a
The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX lines are
Checking and adding manual transmission fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug and inspect the fluid level.3. Note: The
• Fill level for V6• Fill level for V84. Add enough fluid through the filler opening to bring the fluid up tothe recommended levels.5. Install and tig
Changing the air filter elementV6 engineV8 engine1. Release the clamps that secure the air filter housing cover.2. Remove the air filter element from
MOTORCRAFT PART NUMBERSComponent 4.0L V6 engine 4.6L V8 engineAir filter element FA-1773 FA-1897Fuel filter FG-1083 FG-1083Battery BXT-96R BXT-96ROil
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord part name orequivalentFord part number /Ford SpecificationBrake fluid and (clutchfl
Item CapacityFord part name orequivalentFord part number /Ford SpecificationEngine oil(4.0L engine)5.0 quarts (4.7L)•Motorcraft威 SAE 5W-30Premium Synt
Item CapacityFord part name orequivalentFord part number /Ford SpecificationLock cylinders —Motorcraft威 Penetratingand Lock LubricantXL-1 /NonePower s
Item CapacityFord part name orequivalentFord part number /Ford SpecificationWindshield washer fluid 3.6 quarts (3.4L)Motorcraft威 PremiumWindshield Was
ENGINE DATAEngine 4.0L V6 engine 4.6L V8 engineCubic inches 245 281Required fuel 87 octane 87 octaneFiring order 1-4-2-5-3-6 1-3-7-2-6-5-4-8Ignition s
Maintenance and Specifications 259Engine compartment 261Engine oil 264Battery 269Engine coolant 271Fuel information 277Air filter(s) 292Part numbers 2
• They will not reappear until an ignition off-on cycle has beencompleted.This acts as a reminder that these warning conditions still exist withinthe
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
LifestyleAsh cup / smoker’s packageCargo organization and managementPeace of mindFull vehicle coversRemote startVehicle security systemsWheel locksFor
FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on
Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With
Ford Extended Service Plan3062010 05+ Mustang (197)Owners Guide, 3rd PrintingUSA (fus)
AAccessory delay ...79AdvanceTrac ...197AdvanceTrac Sport Mode ...202Air cleaner filter ...
in rear seat ...146LATCH ...149recommendations ...143Child safety seats -
cleaning ...253coolant ...271fail-safe cooling ...275idle speed
TIRE PRESSURE MONITOR FAULT — Displayed when the TirePressure Monitoring System is malfunctioning. If the warning stays on orcontinues to come on, con
lighting up paneland interior ...62JJack ...222positioning ...
Power mirrors ...80Power point ...76Power steering ...202fluid, checkin
TTemporary mobility kit ...227Tilt steering wheel ...73Tire Pressure MonitoringSystem (TPMS)Tires, Wheels and Loading ...
AUDIO SYSTEMSAM/FM CD/MP3 satellite compatible sound systemWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury
Setting the clockTo set the time, press CLOCK. Thedisplay will read SET TIME. Use thememory preset numbers (0–9) toenter in the desired time–hours and
Saving presets automatically: Autoset allows you to set the strongestlocal radio stations without losing your original manually set presetstations for
CD/MP3 PlayerCD: Press to enter CD/MP3 mode. Ifa disc is already loaded into thesystem, CD/MP3 play will beginwhere it ended last. If no CD is loaded,
SEEK: Press SEEK toaccess the previous/next track.CAT (Category) / FOLD(Folder):In MP3 mode only– PressCAT/FOLD and thenpressSEEK to access the previo
Satellite Radio (if equipped)Satellite radio is available only with a valid SIRIUS威 radiosubscription. Check with your authorized dealer for availabil
TEXT: Press and release to displaythe artist and song title. While inTEXT MODE, press again to scrollthrough the Artist (AR), Song (SO), Channel (CH)
titles, the display will read REPLACE SONG? Press OK to access thesaved titles and pressSEEK to cycle through the saved titles.When the song title app
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
b. CHANGE PIN: Press OK when CHANGE PIN is displayed. Thedisplay will read ENTER OLD PIN. Enter your current (old) PINnumber and when the system accep
Extra FeaturesAUX: Press repeatedly to cyclethrough LINE (auxiliary audiomode) and SYNC威 (if equipped).For auxiliary jack location and further informa
Your vehicle is equipped with anauxiliary input jack (AIJ) located inthe center console. The auxiliaryinput jack provides a way to connectyour portabl
7. Adjust the sound on your portable music player until it reaches thelevel of the FM station or CD by switching back and forth between theAUX and FM
Your vehicle may be equipped with aUSB port inside your center console.This feature allows you to plug inmedia playing devices, memorysticks, and also
CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C
CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required. Thism
Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti
Radio Display Condition Action RequiredNO SIGNAL Loss of signal fromthe SIRIUS威 satelliteor SIRIUS威 tower tothe vehicle antenna.You are in a location
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the
5. Recirculated air: Press to activate/deactivate air recirculation inthe vehicle. Recirculated air may reduce the amount of time needed tocool down t
• To improve the A/C cool down, drive with the windows slightly openfor 2-3 minutes after start up or until the vehicle has been “aired out.”During ex
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(NAVIGATION BASED – IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Messa
5. Passenger heated seat (if equipped): Press to control thepassenger heated seat. Refer to Heated seats in the Seating and SafetyRestraints chapter f
TOUCHSCREEN FUNCTIONSTemperature conversion: To switch between Fahrenheit and Celsius,refer to Message center in the Instrument Cluster chapter.Temper
Operating tips• To reduce fog build-up on the windshield during humid weather,select(defrost). Temperature and/or fan speed can also beincreased to im
REAR WINDOW DEFROSTERRPress the control to clear the rear window of thin ice and fog. The LEDwill illuminate.The rear window defroster turns off autom
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the low beam headlampso
Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance
The autolamp system also keeps the lights on for a predeterminedamount of time after the ignition switch is turned to off. You can changethe amount of
High beamsPush the lever toward theinstrument panel to activate. Pullthe lever toward you to deactivate.Flash-to-passPull toward you, to the first det
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parking lampopera
3. Turn on the low beam headlamps to illuminate the wall or screen andopen the hood. To see a clearer light pattern for adjusting, block thelight from
5. Then use a 7mm Allen wrench or a Phillips screwdriver to adjust theheadlamp up or down. HORIZONTAL AIM IS NOT REQUIRED FOR THISVEHICLE AND IS NON-A
Examples of acceptable condensation are:• Presence of thin mist (no streaks, drip marks or droplets)• Fine mist covers less than 50% of the lensExampl
Replacing interior bulbsCheck the operation of all bulbs frequently.Replacing exterior bulbsCheck the operation of all bulbs frequently.Replacing head
Replacing front parking lamp/turn signal bulbs1. Make sure the headlamp control is in the off position and open thehood.Halogen headlampHID headlamp2.
Replacing front sidemarker bulb1. Make sure the headlamp control is in the off position.2. Remove the hex head screwsattaching the underbody forwardae
3. Unbolt the three tail lampattachment nuts and remove thelamp assembly.4. Rotate the LED assemblycounterclockwise and remove itfrom the lamp assembl
Event Data RecordingOther modules in your vehicle — event data recorders — arecapable of collecting and storing data during a crash or nearcrash event
Replacing rear sidemarker lamp bulbs1. Make sure the headlamp switch isin the off position and locate thesidemarker on the rear bumperfascia.2. Insert
Replacing fog lamp bulbs (V6) (if equipped)1. Make sure the headlamp control is in the off position and open thehood.2. Remove the hex head screwsatta
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT STEERING WHEELTo adjust the steering wheel:1. Push the lever down to unlockthe steering column. While the leveris in the down position, tilt thes
Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the on p
2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons.3. Slowly d
AUXILIARY POWER POINT (12VDC)Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will damag
Press and pull the switches to openand close windows.• Press down (to the first detent)and hold the switch to open.• Pull up (to the first detent) and
Bounce-back override (front windows only)To override bounce-back, within two seconds after reaching bounce-backposition, if the switch is moved from t
In the event that the rear quarter window switch does not operate whenthe convertible top is completely up or down, the rear quarter windowscan be man
information”) only to help provide you with the directions, trafficreports, or business searches you request. If you do not wantFord or its vendors to
Note: If equipped with a rearview camera system, a video image will bedisplayed in the mirror or the navigation system display (if equipped)when the v
Optional controls1. Press the ON control and release it.2. Accelerate to the desired speed.Base controlsOptional controls3. Press the SET (+) control
Resuming a set speedBase controlsOptional controlsPress the RES / RESUME control and release it. This will automaticallyreturn the vehicle to the prev
Reducing speed while using speed controlBase controlsOptional controlsThere are two ways to reduce a set speed:• Press and hold the SET (-) control un
STEERING WHEEL CONTROLS (IF EQUIPPED)With navigation system (ifequipped)• Pressto use the voicecommand features.For further information on usingvoice
• Press to change radio stations/CD tracks.CONVERTIBLE (IF EQUIPPED)Do not store articles behind rear seat. Articles stored in the convertibletop stow
4. Press the convertible top switchon the overhead console and holduntil the windows are completelydown and the top is completelystored.Installation o
4. Tuck the boot corners behind the shoulder belts.5. Secure the boot straps on the rear seat hooks behind the rear seat.Note: Improper installation c
3. Fold the right side inward and secure the boot with the strap.Stow the boot in the trunk.Raising the convertible topThe convertible top will not op
Note: The latch handles must be pulled downwards fully to allow thelatch to fully rotate into the closed position.5. Secure the driver’s side latch fi
EXPORT UNIQUE (NON–UNITED STATES/CANADA) VEHICLESPECIFIC INFORMATIONFor your particular global region, your vehicle may be equipped withfeatures and o
Interior trunk control lockout (convertible vehicles only)This feature helps prevent unauthorized access to the trunk when theconvertible top is open,
KEYSYour vehicle may be equipped withtwo Integrated KeyheadTransmitters (IKTs). The key bladefunctions as a programmed keywhich starts the vehicle and
Press the control to unlock alldoors.Press thecontrol to lock alldoors.Locking and unlocking with keysYour vehicle’s keys are designed to lock and unl
The autolock feature repeats when:• any door is opened then closed while the ignition is in the on positionand the vehicle speed is 9 mph (15 km/h) or
8. Turn the ignition to the off position. The horn will chirp once toconfirm the procedure is complete.Autounlock (if equipped)The autounlock feature
6. To enable/disable the autounlock feature, press the lock control, thenpress the unlock control. The horn will chirp once if autounlock wasdeactivat
WARNING: Do not leave children, unreliable adults, or animalsunattended in the vehicle. On hot days, the temperature in thetrunk or vehicle interior c
The IKT allows you to:• remotely unlock the vehicledoors.• remotely lock all the vehicledoors.• remotely open the trunk.• activate the personal alarm.
two stage unlock allows all vehicle doors to unlock simultaneously). Theturn lamps will flash twice to indicate that two-stage unlock was enabledor di
The remote entry system allows you to open the trunk while the ignitionis in any position. However, if the ignition is in the on position and thevehic
Commentaires sur ces manuels