Ford 2010 Expedition v.1 Manuel d'utilisateur

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Message center 20Entertainment Systems 39How to get going 39AM/FM stereo with

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

WARNING: The driver should not attempt to operate anyfunction of the DVD system while the vehicle is in motion. Givefull attention to driving and to t

Care and service of the DVD playerEnvironmental extremesDVD players which are subjected to harsh environmental conditions maybe damaged or perform at

Cleaning DVD and CD discsInspect all discs for contamination before playing. If necessary, cleandiscs only with an approved DVD and CD cleaner and wip

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele

6. Fan speed adjustment: Controls the volume of air circulated in thevehicle.Manual heating and air conditioning system with rear passengercompartment

4. REAR Rear temperature control: Press to enable theauxiliary system and to set the desired rear cabin airflow temperaturewith the front control. The

• During extreme high ambient temperatures when idling stationary forextended periods of time in gear, it is recommended to run the A/C inthe MAX A/C

2. Rear temperature control: Press to enable the auxiliary system andset the desired rear cabin airflow temperature with the front control. Therear ca

12. Manual override controls: Allows you to manually select whereairflow is distributed. To return to full automatic control, press AUTO.13. FFront fa

Dual automatic temperature control with heated and cooled seatsand rear passenger compartment climate control (if equipped)1.Defrost: Distributes outs

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

5. R Rear fan speed control: Press to enable the auxiliary systemor to adjust the rear fan speed from the front control. Press to manuallyincrease or

14. Driver temperature control: Press to increase or decrease thetemperature on the driver side of the cabin. Sets the passenger sidetemperature also

• For maximum cooling performance, (MAX A/C):In AUTO: Press AUTO control and set to desired temperature.In Manual Override: Press the(panel), A/C, and

REAR WINDOW DEFROSTERRThe rear defroster control is locatedon the climate control panel andworks to clear the rear window offog and thin ice.The engin

HEADLAMP CONTROLRotate the headlamp control to thefirst positionto turn on theparking lamps.Rotate to the second positiontoturn on the headlamps.Rotat

Fog lamp control (if equipped)The headlamp control also operatesthe fog lamps. The fog lamps can beturned on when the headlampcontrol is in the, orpos

WARNING: Always remember to turn on your headlamps atdusk or during inclement weather. The Daytime Running Lamp(DRL) system does not activate the tail

1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters)away.• (1) 8 feet (2.4 meters)• (2) Cen

TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSFront row map lamps (if equipp

Second row map lamps (if equipped)The second row map lamps arelocated in the headliner above thesecond row seats.The second row map lamp lightswhen:•

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa

BULB REPLACEMENTLamp assembly condensationExterior lamps are vented to accommodate normal changes in pressure.Condensation can be a natural by-product

Function Number of bulbs Trade numberHeadlamps (low andhigh-beam)2 H13/9008Front sidemarker 2 194Front park/turn lamps 2 3157 AFog lamps 2 9145Front r

Replacing headlamp bulbs1. Make sure that the headlamp control is in the off position.2. Open the hood.3. At the back of the headlamp,remove the two h

Replacing front parking lamp/turn/sidemarker signal bulbs1. Make sure that the headlamp control is in the off position.2. Open the hood.3. At the back

4. Rotate the bulb socket counterclockwise and remove from lampassembly.5. Pull bulb straight out of socket and snap in the new bulb.6. Install the bu

Replacing license plate lamp bulbThe license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Courtesy wipe feature: One extra wipe will occur a few seconds afterwashing the front window to clear any excess washer fluid remaining onthe windshie

TILT STEERING WHEEL1. Pull and hold the steering wheelrelease control toward you.2. Move the steering up or downuntil you find the desired location.3.

OVERHEAD CONSOLEThe appearance of your vehicle’s overhead console will vary according toyour option package.Forward storage bin (if equipped)The stora

chapter. If the light is blinking, engine misfire is occurring which coulddamage your catalytic converter. Drive in a moderate fashion (avoidheavy acc

Power quarter rear windows (if equipped)Press the VENT portion of thecontrol to open the power rearquarter windows.Pull the VENT control to close thep

AUXILIARY POWER POINT (12VDC)Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will damag

POWER WINDOWSWARNING: Do not leave children unattended in the vehicle anddo not let children play with the power windows. They mayseriously injure the

To operate one-touch up:• Pull the switch completely up tothe second detent and releasequickly. The window will closefully. Momentarily press theswitc

INTERIOR MIRRORThe interior rear view mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side.

EXTERIOR MIRRORSPower side view mirrorsThe ignition can be in any position to adjust the power side view mirrors.To adjust your mirrors:1. Rotate the

Note: 10 or more switch activations within one minute, or repeatedfolding/unfolding of the mirrors while holding the switch rearward duringfull travel

WARNING: Never adjust the accelerator and brake pedal withfeet on the pedals while the vehicle is moving.POWER DEPLOYABLE RUNNING BOARDS (IF EQUIPPED)

Note: The running boards may operate slower in cooler temperatures. Inadverse conditions, debris such as mud, dirt, and salt may becometrapped in the

Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas

Airbag readiness: If this light failsto illuminate when the ignition isturned to on, continues to flash orremains on, have the systemserviced immediat

Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed.Increasing spee

Turning off speed controlThere are two ways to turn off the speed control:• Press the brake pedal. This will not erase your vehicle’s previously setsp

In CD mode (if equipped):• PressSEEK to select the next selection on the CD/USBor press and hold to forward or reverse through the CD/USB.In DVD mode

Press to activate phone mode or answer a phone call. Press andholdto end call or exit phone mode.Pressto scroll through various menus and selections.

WARNING: When closing the moon roof, you should verify thatit is free of obstructions and ensure that children and/or pets arenot in the proximity of

Car2U威 Home AutomationSystemHomeLink姞 Wireless Control System (if equipped)The HomeLink威 Wireless ControlSystem, located on the driver’s visor,provide

ProgrammingDo not program HomeLink威 with the vehicle parked in the garage.Note: Your vehicle may require the ignition switch to be turned to theaccess

press/hold/release sequence again and, depending on the brand of thegarage door opener (or other rolling code equipped device), repeat thissequence a

Erasing HomeLink姞 buttonsTo erase the three programmedbuttons (individual buttons cannotbe erased):• Press and hold the two outerHomeLink威 buttons unt

WARNING: Make sure that people and objects are clear of thegarage door or security device you are programming. Do notprogram the Car2U威 system with th

Low tire pressure warning(if equipped): Illuminates whenyour tire pressure is low. If the lightremains on at start up or whiledriving, the tire pressu

If you do not know if your garagedoor opener is a rolling code orfixed code device, open your garagedoor opener’s remote control batterycover. If a pa

2. Go to the garage to locate thegarage door opener motor and its“learn” button. You may need aladder to reach the unit and youmay need to remove the

Note: The Car2U威 system allows for three devices to be programmed. Ifyou need to change or replace any of the three devices after it has beeninitially

3. To input these positions into theCar2U威 system, simultaneouslypress all three Car2U威 systembuttons for a few seconds and thenrelease to put the dev

To erase programming on the Car2U威 system (individual buttons cannotbe erased), use the following procedure:1. Firmly press the two outsideCar2U威 syst

WARNING: Keep keys out of reach of children. Do not allowchildren to play near an open or moving power liftgate.The liftgate will only operate with th

To open the liftgate with outsideliftgate control button (manualactuation):1. Unlock the liftgate with theremote entry transmitter or powerdoor unlock

Note: In case of operation in extreme cold -40°F (-40°C), or on extremeinclines, manual operation of the liftgate is suggested.Obstacle detectionThe p

Liftgate windowTo open the liftgate window, pressthe button on the left side of theliftgate above the license plate.MANUAL LIFTGATE (IF EQUIPPED)The l

CARGO MANAGEMENT SYSTEM (IF EQUIPPED)The cargo management systemconsists of a storage compartmentlocated in the floor of the rear cargoarea.1. To open

4X2 (RTT) (if equipped):Displays momentarily whentwo-wheel drive high is selected. Ifthe light fails to display when theignition is turned on, or rema

WARNING: Do not load any objects on the shelf that mayobstruct your vision or strike occupants of the vehicle in thecase of a sudden stop or collision

KEYSYour vehicle may be equipped withtwo Integrated KeyheadTransmitters (IKTs). The key bladefunctions as a programmed keywhich starts the vehicle and

POWER DOOR LOCKSPress control to unlock all doors.Press control to lock all doors.Smart locksThis feature helps to prevent you from locking yourself o

The autolock feature repeats when:• any door is opened then closed while the ignition is in the on positionand the vehicle speed is 9 mph (15 km/h) or

Keyless entry keypad procedure1. Turn the ignition to the off position.2. Close all doors, the liftgate and liftgate window.3. Enter 5–digit entry cod

Power door lock switch autounlock enable/disable procedureBefore starting, ensure the ignition is in the off position and all vehicledoors are closed.

CHILDPROOF DOOR LOCKSWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo

The IKT allows you to:• remotely unlock the vehicledoors.• remotely lock all the vehicledoors.• remotely open the power liftgateor manual liftgate win

Locking the doors1. Press and release to lock all the doors. The parking lamps willilluminate.2. Pressand release again within three seconds to confir

Sounding a panic alarmPressto activate the alarm. The horn will sound and the turn lampswill flash for a maximum of three minutes. Press again or turn

Headlamps on warning chime: Sounds when the headlamps or parkinglamps are on, the ignition is off (the key is not in the ignition) and thedriver’s doo

3. A tone will be heard when the deactivation is complete.4. Repeat this procedure for another remote entry transmitter if desired.Replacing the batte

Illuminated entryThe interior lamps, parking lamps and puddle lamps (if equipped)illuminate when the Integrated Keyhead Transmitter or the keyless ent

• activate or deactivate the Autolock feature if equipped• release the liftgate glass,The keypad can be operated with the factory set 5–digit entry co

The anti-scan feature will turn off after:• one minute of keypad inactivity,• pressing thecontrol on the remote entry transmitter,• or the ignition po

engine. If a problem occurs, turn the ignition off, remove all objects onthe key chain away from the coded IKT and restart the engine.Note: Do not lea

Key informationYour vehicle is supplied with two coded keys. Only a coded key willstart your vehicle. Spare coded keys can be purchased from yourautho

Tips:• Only use Integrated Keyhead Transmitters (IKTs) or standardSecuriLock威 keys.• You must have two previously programmed coded keys (keys thatalre

If the key has been successfully programmed it will start the vehicle’sengine and will operate the remote entry system (if the new key is anIntegrated

• Visual warnings are displayed followed by a chime when a preselectedvehicle speed of 45, 55 or 65 mph (75, 90, or 105 km/h) is exceeded• The maximum

3. If you don’t want to change the maximum speed setting, press theSETUP button to display the next menu. The remaining menus appear asfollows with th

Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature, the needle will be inthe normal range (between “

TroubleshootingCondition Potential CausesCan’t create a MyKey™ • Key in the ignition is already aMyKey™• Key in the ignition is the lastremaining Admi

Arming the systemWhen armed, this system will respond if unauthorized entry isattempted. When unauthorized entry occurs, the system will flash theturn

Disarming the systemYou can disarm the system by any of the following actions:• Unlock the doors by using the remote entry transmitter portion ofyour

SEATINGAdjustable head restraintsYour vehicle is equipped with front row outboard head restraints that arevertically adjustable.WARNING: To minimize t

3. Lower the head restraint bypressing and holding the guidesleeve adjust/release button andpushing down on the head restraint.Properly adjust the hea

2. Simultaneously press and holdboth the adjust/release button andthe unlock/remove button, then pullup on the head restraint.To reinstall the adjusta

Lift handle to move seat forward orbackward.Manual seat recliner (if equipped)WARNING: Always drive and ride with your seatback uprightand the lap bel

Using the armrest (if equipped)Push the release control to movethe armrest up or down.Using the manual lumbar support (if equipped)The lumbar support

Using the power lumbar support (if equipped)The power lumbar control is located on the outboard side of the seat.Press the forward side of the control

Move the switch in the direction ofthe arrows to raise or lower the rearportion of the seat cushion.Press the switch in the direction ofthe arrows to

Tachometer: Indicates the enginespeed in revolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the

Memory seat/power mirrors/adjustable pedals (if equipped)This system allows automaticpositioning of the driver seat,outside rearview mirrors andadjust

Heated seatsWARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cordinjury, medication,

Climate controlled seats air filter replacement (if equipped)The climate controlled seat system includes air filters that must bereplaced periodically

To install a filter:• First, position the filter in itshousing making sure that the farforward end is all the way up inthe housing. Then push in on th

2. Locate handle on the side of theseat cushion by the door.3. Pull up on the handle and pushthe seatback forward toward thefront of the vehicle.To re

Placing the 2nd row outboard 40% seats in cargo modeWARNING: Use caution when folding the seatback to the flatback position as the system will move fo

Returning to the upright position from full lowered load floorpositionThe seatback cannot be returned to the upright position until the seat isreturne

To return the seat to a seating position:1. Push the seat down and latch tothe floor with a moderate amount ofeffort and speed.2. Make sure the seat i

Exiting the 3rd row1. Pull the strap located at thebottom outboard of the seat back torelease the seat from the floor, androtate the seat up towards t

WARNING: To prevent possible damage to the seat or safetybelts, ensure that the safety belts are not buckled when movingthe seat to the load floor pos

Locks and Security 161Keys 161Locks 162Anti-theft system 173Seating and Safety Restraints 183Seating 183Safety restraints 204Airbags 217Child restrain

STANDARD MESSAGE CENTER (IF EQUIPPED)Your vehicle’s message center is capable of monitoring many vehiclesystems and will alert you to potential vehicl

Adjusting the 2nd row center 20% seat (if equipped)Lift the handle to move the seatforward or backward.Note: This seat can be moved forward to keep a

To operate the heated seats:• Push the indicated side of thecontrol for maximum heat.• Push again to deactivate.• Push the indicated side of thecontro

Folding down the 3rd row seats to the load floorWARNING: To prevent possible damage to the seat or safetybelts, ensure that the safety belts are not b

Third row power folding seat (if equipped)Note: Be sure that the headrestraints are folded down beforepowering the 3rd row seat down.The control butto

The power fold down seats will operate for 10 minutes after theignition switch is in off. The transmission must be in P (Park),and the liftgate, or li

the system. Rather, it means the Personal Safety System威 determinedthe accident conditions (crash severity, belt usage, etc.) were notappropriate to a

Front safety belt energy management retractorsThe front outboard safety belt energy management retractors allowwebbing to be pulled out of the retract

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

Combination lap and shoulder belts1. Insert the belt tongue into the proper buckle (the buckle closest tothe direction the tongue is coming from) unti

Webbing extraction sensitive modeThe webbing sensitive locking mode locks the webbing and preventsmore belt from being pulled out if the belt is pulle

If you calculate your average fuel economy by dividing distance traveledby gallons of fuel used (liters of fuel used by 100 kilometers traveled),your

How to disengage the automatic locking modeUnbuckle the combination lap and shoulder belt and allow it to retractcompletely to disengage the automatic

Safety belt height adjustmentYour vehicle has safety belt heightadjustments for the driver and rightfront passenger. Adjust the height ofthe shoulder

To adjust the comfort guide:1. Slip the shoulder belt into thebelt guide. (The portion of the beltbetween the latch tongue and theD-ring, not the port

Conditions of operationIf... Then...The driver safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt warni

If... Then...The driver’s safety belt is notbuckled approximately fiveseconds after the safety beltwarning light has turned off...The Belt-Minder威 fea

Reasons given... Consider...“I was in a hurry” Prime time for an accident.Belt-Minder威 reminds us to take afew seconds to buckle up.“Safety belts don’

WARNING: Do not sit on top of a buckled safety belt or insert alatchplate into the buckle to avoid the Belt-Minder威 chime. Todo so may adversely affec

4. Within approximately seven seconds of the light turning off, bucklethen unbuckle the safety belt.• This will disable the Belt-Minder威 feature for t

WARNING: All occupants of the vehicle, including the driver,should always properly wear their safety belts, even when an airbag supplemental restraint

WARNING: Additional equipment may affect the performance ofthe airbag sensors increasing the risk of injury.Children and airbagsChildren must always b

1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Press and release theSELECT/RESET stem to scroll

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

• one or more impact and safing sensors and diagnostic monitor (RCM),• a readiness light and tone• the electrical wiring which connects the components

WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. Contact your authorize

The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of

WARNING: Do not attempt to service, repair, or modify theSafety Canopy威 system, its fuses, the A, B, C or D pillar trim, orthe headliner on a vehicle

• Two crash sensors mounted in the front doors (one on each side ofthe vehicle).• Two crash sensors located at the C pillar behind the rear doors (one

WARNING: If the SafetyCanopy威 system hasdeployed, the Safety Canopy威 willnot function again unless replaced.The Safety Canopy威 system(including the A,

The SOS Post-Crash Alert can be turned off when any one of thefollowing actions are taken by the driver or any other person:• pressing the hazard cont

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

5. Press and hold the SELECT/RESET stem until the message centerdisplays CIRCLE SLOWLY TO CALIBRATE. This step may require up tofive circles to comple

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

restrained properly, then restrain the child in the child safety seat orwith the belt-positioning booster. Remember that child seats andbelt-positioni

When installing a child safety seat with combination lap/shoulder belts:• Use the correct safety belt buckle for that seating position.• Insert the be

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out.6. All

10. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the

Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol.The LATCH anchors are locat

WARNING: Never attach two child safety seats to the sameanchor. In a crash, one anchor may not be strong enough to holdtwo child safety seat attachmen

The tether strap anchors in your vehicle are in the following positions(shown from top view):• Second row bench seat• Second row bucket seatsAttach th

• Second row outboard seatingpositions• Second row center seatingposition (if equipped)3. Grasp the tether strap andposition it to the seat frame.4. R

OIL LIFEThis displays the remaining oil life.An oil change is required whenever indicated by the message center andaccording to the recommended mainte

5. Rotate the tether strap clip.6. Tighten the child safety seat tether strap according to themanufacturer’s instructions.Third row center seating pos

3. Clip the tether strap through theanchor loop as shown.If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly

Booster seats position a child so that vehicle lap/shoulder safety belts fitbetter. They lift the child up so that the lap belt rests low across the h

Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

AUTOUNLOCKThis feature automatically unlocks all vehicle doors when the driver’sdoor is opened within 10 minutes of the ignition being turned off.Pres

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air

The cold inflation pressure should never be set lower than therecommended pressure on the Safety Compliance Certification Label orTire Label.When weat

TIRE CAREInspecting your tires and wheel valve stemsPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones

WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressur

WARNING: Only use replacement tires and wheels that are thesame size, load index, speed rating and type (such as P-metricversus LT-metric or all-seaso

It is recommended that the two front tires or two rear tires generally bereplaced as a pair.The tire pressure sensors mounted in the wheels (originall

Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your

Note: If your tires show uneven wear ask an authorized dealer to checkfor and correct any wheel misalignment, tire imbalance or mechanicalproblem invo

4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new

• Some messages will reappear after clearing or being reset if a problemor condition is still present and needs your attention.• Some messages can be

8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n

13. Maximum Permissible Inflation Pressure: Indicates the tiremanufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti

When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.

Low Tire PressureWarning LightPossible cause Customer Action RequiredFlashing WarningLightSpare tire in use Your temporary spare tire is inuse. Repair

SNOW TIRES AND CHAINSWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel

capability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design performance. Before loadingyour vehi

FOR 4X4 LOW SLOW TO 3 MPH (if equipped) — Displayed when4X4 LOW is selected while the vehicle is moving. For more information,refer to Control trac fo

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400

• Thoroughly prepare your vehicle for towing. Refer to Preparing totow in this chapter.• Use extra caution when driving while trailer towing. Refer to

EngineRear axleratioMaximum GCWR -lb. (kg)Trailer weightrange (0 -maximum) lb. (kg)4x25.4L withstandardtrailer towpackageAll 11800 (5352) 0–6000 (0–27

EngineRear axleratioMaximum GCWR -lb. (kg)Trailer weightrange (0 -maximum) lb. (kg)Expedition EL (U.S. Only) Expedition Max (Canada Only) 4x25.4L with

Integrated hitch ratingThe standard integrated hitch has two ratings depending on mode ofoperation:• Weight carrying - requires a draw bar and hitch b

KEY COULD NOT PROGRAM — Displayed when an attempt is madeto program a spare key using two existing MyKeys. Refer to MyKey™ inthe Locks and Security ch

Weight distributing hitchWhen hooking up a trailer using a load equalizing hitch, always use thefollowing procedure:1. Park the unloaded vehicle on a

The braking system of the tow vehicle is rated for operation at theGVWR not GCWR.Trailer lampsTrailer lamps are required on most towed vehicles. Make

• Allow more distance for stopping with a trailer attached.• If you are driving down a long or steep hill, shift to a lower gear. Donot apply the brak

RECREATIONAL TOWINGFollow these guidelines if you have a need for recreational towing. Anexample of recreational towing would be towing your vehicle b

STARTINGPositions of the ignition1. Off— locks the steering wheel,automatic transmission gearshiftlever and allows key removal.2. Accessory— allows th

WARNING: If you smell exhaust fumes inside your vehicle, haveyour dealer inspect your vehicle immediately. Do not drive if yousmell exhaust fumes.Impo

4. Make sure the parking brake isset.5. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminate. See Wa

3. After idling for a few seconds, release the parking brake, apply thebrake, shift into gear and drive.Note: If the engine does not start on the firs

Guarding against exhaust fumesCarbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects.WARNING: If you smell exhaus

WARNING: To reduce the risk of electrical shock, do not useyour heater with ungrounded electrical systems or two-pronged(cheater) adapters.Prior to us

InfoPress the INFO button repeatedly tocycle through the following features:TRIP A/BRegisters the distance of individual journeys. Press and release I

How to use the engine block heaterEnsure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth.Depending on the type

Anti-lock brake system (ABS)On ABS-equipped vehicles, a noise from the hydraulic pump motor andpulsation in the pedal may be observed during ABS braki

Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.ADVANCETR

WARNING: If a failure has been detected within theAdvanceTrac威 with RSC威 system, the ⬙sliding car⬙ iconwillilluminate steadily. Verify that the Advanc

Note: If the system cannot be turned off, refer to MyKey™ in the Locksand Security chapter for more information.When AdvanceTrac威 with RSC威 performs a

Electronic Stability Control (ESC)Electronic Stability Control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa

Switching Off Traction ControlIf the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off the Traction Control features

During trailer sway control events the “sliding car” icon in theinstrument cluster will flash momentarily. The cluster message centerwill also display

If the power steering system breaks down (or if the engine is turnedoff), you can steer the vehicle manually, but it takes more effort.If the steering

Customer Assistance 352Reporting safety defects (U.S. only) 358Reporting safety defects (Canada only) 358Cleaning 359Maintenance and Specifications 36

AVG MPG (L/100km)Average fuel economy displays your average fuel economy in miles/gallonor liters/100 km.If you calculate your average fuel economy by

If the system is off, the rear air suspension will not operate and will notraise (pump) or lower (vent) while the vehicle is not moving. However, ifth

WARNING: Loaded vehicles, with a higher center of gravity,may handle differently than unloaded vehicles. Do not overloadyour vehicle and use extra pre

4. Using a flat-head screwdriver orsimilar tool, move the brake-shiftinterlock actuator spindle towardthe left, apply the brake and shiftthe transmiss

If the fuse is not blown and the brakelamps are working properly, thefollowing procedure will allow you to move the gearshift lever from P(Park):1. Ap

WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your author

To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)WARNING: Always set the parking b

• Floor-shift transmissionThe TOW HAUL indicator light willilluminate in the instrument cluster.Tow/Haul delays upshifts to reduce frequency of transm

2 (Second)Transmission operates in 2nd gear only.Use 2 (Second) to start-up on slippery roads or to provide additionalengine braking on downgrades.1 (

WARNING: To help avoid personal injury, always use cautionwhen in R (Reverse) and when using the reverse sensing system.WARNING: This system is not de

While receiving a warning the radio volume will be reduced to apredetermined level. After the warning goes away, the radio will returnto the previous

System check and vehicle feature customizationPress the SETUP button repeatedlyto cycle the message center throughthe following features:RESET FOR SYS

The message center will indicate the system is off and will not allow thedriver to switch the system on to indicate a failure of the reverse sensingsy

Image delay if displayed through the rearview mirror:When shifting out of R (Reverse) and into any other gear, the image inthe rearview mirror will re

If the back end of the vehicle is hit or damaged, then check with yourauthorized dealer to have your rear video system checked for propercoverage and

4WD indicator lightsThe indicator lights illuminate in the message center in thereconfigurable telltale (RTT) location under the following conditions.

dry pavement. This position is only intended for severe winter oroff-road conditions, such as deep snow, ice or shallow sand.• 4L (4X4 LOW) provides e

Shifting between 4A and 4HMove the control between 4A to 4H at a stop or while driving at anyspeed. The message center will display “4X4” if 4H is sel

Maintain steering wheel control at all times, especially in rough terrain.Since sudden changes in terrain can result in abrupt steering wheelmotion, m

If your vehicle gets stuckIf your vehicle gets stuck in mud or snow it may be rocked out byshifting between forward and reverse gears, stopping betwee

WARNING: Vehicles with a higher center of gravity such asutility and four-wheel drive vehicles handle differently thanvehicles with a lower center of

Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required f

Note: To change oil life 100% miles value from 7,500 miles (12,000 km)or 12 months to another value, proceed to Step 3.3. Once “OIL LIFE SET TO XXX%”

“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nationswilderness are

Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;

WARNING: If you are driving in slippery conditions that requiretire chains or cables, then it is critical that you drive cautiously.Keep speeds down,

DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

Canadian customers refer to your Customer Information Guidefor information on:• coverage period• exact fuel amounts• towing of your disabled vehicle•

Note: With extended use, the flasher may run down your battery.FUEL PUMP SHUT-OFF SWITCHFUELRESETThe fuel pump shut-off switch is a device intended to

FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth

Passenger compartment fuse panelThe fuse panel is located under the right-hand side of the instrumentpanel.To remove the trim panel for accessto the f

The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Smart window #12 15A Driver side memory module3 15A Family ente

Press the RESET button to turn autounlock on or off.RUNNING BOARDS (if equipped)This feature automatically deploys the side running boards for easyent

Fuse/RelayLocationFuse AmpRatingProtected Circuits23 15A High beam headlamps24 20A Horn25 10A Demand lamps, Glovebox, Visor26 10A Instrument panel clu

Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot

Fuse/RelayLocationFuse AmpRatingProtected Circuits4 — Trailer tow battery charge relay5 — Fuel pump relay6 — Electronic fan 1 relay7 — Rear window def

Fuse/RelayLocationFuse AmpRatingProtected Circuits32 40A** Blower motor relay33 — Not used34 30A** Auxiliary blower motor35 30A** PCM relay36 30A** Po

Fuse/RelayLocationFuse AmpRatingProtected Circuits59 15A* Heated mirrors60 — One-touch start diode61 — Fuel pump diode62 — Not used63 25A** Electronic

CHANGING THE TIRESIf you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel

2. Full-size dissimilar spare with label on wheel: This spare tire hasa label on the wheel that states: “THIS TIRE AND WHEEL FORTEMPORARY USE ONLY”Whe

• Wet weather driving capability• All-Wheel driving capability (if applicable)• Load leveling adjustment (if applicable)When driving with the full-siz

Removing the jack and tools1. Open the liftgate, then locate theaccess panel on the floor behind the3rd row seat. Unlatch and removethe panel.2. Remov

Tire change procedureWARNING: To help prevent the vehicle from moving when youchange a tire, be sure the parking brake is set, then block thewheels (b

Most geographic areas (zones) have a magnetic north compass point thatvaries slightly from the northerly direction on maps. This variation is fourdegr

1. Block the wheels (both front orboth rear) on the opposite end ofthe vehicle from the wheel beingchanged. If on a grade, block bothwheels on the dow

WARNING: When one of the rear wheels is off the ground, thetransmission alone will not prevent the vehicle from moving orslipping off the jack, even i

• Never use the front or reardifferential as a jacking point.WARNING: To lessen the risk of personal injury, do not put anypart of your body under the

2. Slide the wheel partially underthe vehicle and install the retainerthrough the wheel center. Ifequipped, you may have to removethe wheel center cap

WARNING: When a wheel is installed, always remove anycorrosion, dirt or foreign materials present on the mountingsurfaces of the wheel or the surface

JUMP STARTINGWARNING: The gases around the battery can explode ifexposed to flames, sparks, or lit cigarettes. An explosion couldresult in injury or v

Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,

4. Make the final connection of the negative (-) cable to the jumpstarting stud located in the engine compartment, near the washer fluidbottle.Note: D

Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.

2. Remove the jumper cable on the negative (-) connection of thebooster vehicle’s battery.3. Remove the jumper cable from the positive (+) terminal of

CREATE MYKEY / MYKEY SETUP / CLEAR MYKEYFor more information refer to MyKey™ in the Locks and Securitychapter.ENGLISH / FRENCH / SPANISH RESET FOR NEW

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

If the vehicle is towed by other means or incorrectly, vehicledamage may occur.Ford Motor Company produces a towing manual for all authorized towtruck

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

If your vehicle must be serviced while you are traveling or living inCentral America, the Caribbean, or the Middle East, contact the nearestauthorized

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is

CHECK CHARGING SYSTEM — Displayed when the electrical systemis not maintaining proper voltage when the engine is running. If you areoperating electric

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent qu

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENSClean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth,

INTERIORFor fabric, carpets, cloth seats, safety belts and seats equipped with sideairbags:• Remove dust and loose dirt with a vacuum cleaner.• Remove

• If the leather cannot be completely cleaned using a mild soap andwater solution, the leather may be cleaned using a commerciallyavailable cleaning p

ScratchesNatural Markings - Because the leather in the seat comes from genuinesteer hides, there will be evidence of naturally occurring markings, suc

FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

Working with the engine on1. Set the parking brake and shift to P (Park).2. Block the wheels.WARNING: To reduce the risk of vehicle damage and/orperso

CHECK AIR SUSPENSION (if equipped) — Displayed when the airsuspension system is not operating properly. If this message is displayedwhile driving, pul

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT5.4L V81. Windshield washer fluid reservoir2. Engine oil dipstick3. Brake fluid reservoir4. Engine coo

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

CHANGING THE WIPER BLADESIt is recommended that wiper blades are renewed before winter.To replace the wiper blades:1. Fold back the wiper arm andposit

4. To attach the new wiper to thewiper arm, align the cross pin andkeyway (denoted with the arrows)and firmly press the wiper bladeinto the wiper arm

• If the oil level is below thismark, engine oil must be addedto raise the level within thenormal operating range.• If required, add engine oil to the

Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by th

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

• If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the FULL COLD level or within theCOLD

MY KEY ACTIVE DRIVE SAFELY — Displayed at startup whenMyKey™ is in use. Refer to MyKey™ in the Locks and Security chapterfor more information.KEY COUL

• Do not mix coolants. Add the coolant type originally equippedin your vehicle. Refer to Maintenance product specifications andcapacities in this chap

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap.5. Fill the coolant reservoi

• NEVER increase the coolant concentration above 60%.• Increased engine coolant concentrations above 60% willdecrease the overheat protection characte

When this occurs the vehicle will still operate. However:• The engine power will be limited.• The air conditioning system will be disabled.Continued o

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsWARNING: Do not overfill the fuel tank. The pressure in anoverfilled tank may c

• Fuels can also be harmful if absorbed through the skin. If fuel issplashed on the skin and/or clothing, promptly remove contaminatedclothing and was

WARNING: When refueling always shut the engine off andnever allow sparks or open flames near the filler neck. Neversmoke while refueling. Fuel vapor i

When fueling your vehicle:1. Turn the engine off.2. Open the fuel filler door.3. Slowly insert the fuel filler nozzle fully into the fuel system. Pump

Flex Fuel Vehicle (FFV) fuel fill inletFlex fuel vehicles have a yellow bezel placed over the fuel fill inlet.Choosing the right fuelUse only UNLEADED

It is best not to alternate repeatedly between gasoline and E85. If you doswitch fuels, it is recommended that you add as much fuel aspossible—at leas

AUDIO SYSTEMSNote: If your volume is muted and MYKEY VOLUME LIMITED isdisplayed, refer to MyKey™ in the Locks and Security chapter for moreinformation

• Normally, adding 1 gallon (3.8L) of fuel is enough to restart theengine. If the vehicle is out of fuel and on a steep grade, more than1 gallon (3.8L

ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform

Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers).2. Each time you fill the tan

• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between the top gears occurs. Unnecessaryshifting of this type co

EPA fuel economy estimatesEvery new vehicle should have a sticker on the window called theMonroney Label which contains EPA fuel economy estimates. Co

WARNING: Exhaust leaks may result in entry of harmful andpotentially lethal fumes into the passenger compartment.Do not make any unauthorized changes

If the service engine soon indicator remains on, have your vehicleserviced at the first available opportunity. Although some malfunctionsdetected by t

POWER STEERING FLUIDCheck the power steering fluid. Refer to scheduled maintenanceinformation.1. Start the engine and let it rununtil it reaches norma

TRANSMISSION FLUIDChecking automatic transmission fluidThe automatic transmission does not have a transmission fluid dipstick.Refer to your scheduled

2. Unlock the locking clip on theconnector (connector shown frombelow for clarity), then squeeze andpull the connector off of the airoutlet tube.3. Cl

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

4. Once you are tuned to thedesired station, press and hold amemory preset (1–6) to save thestation. PRESET SAVED will appear on the display and the s

6. Remove the air filter elementfrom the air filter housing.7. Install a new air filter element.8. Replace the air filter housingcover and secure the

Note: Failure to use the correct air filter element may result in severeengine damage. The customer warranty may be void for any damage tothe engine i

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationBrake fluidBetween MINand MAX onreser

Item Capacity Ford part nameFord part number /Ford specificationEngine oil 7.0 quarts (6.6L)•Motorcraft SAE 5W-20Premium SyntheticBlend Motor Oil•Moto

Item Capacity Ford part nameFord part number /Ford specificationTransfer case fluid (4X4)1.6-1.8 quarts(1.5-1.7L)Motorcraft TransferCase FluidXL–12 /—

ENGINE DATAEngine 5.4L V8 engineCubic inches 330Fuel 87 octane or (E-85)Firing order 1-3-7-2-6-5-4-8Ignition system Coil on plugSpark plug gap 0.039–0

Engine drivebelt routingIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations req

Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX

TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

Listening to a CD/MP3 (if equipped)1. If the audio system is turned off,press VOL-PUSH to turn the radioon. Turn VOL-PUSH to adjust thevolume.Note: Th

LifestyleAsh cup / smoker’s packageCargo organization and managementRoof crossbarsTrailer towing accessoriesPeace of mindRemote startVehicle security

FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan4132010 Expedition (exd)Owners Guide (own2002), 1st PrintingUSA (fus)

AABS (see Brakes) ...291Accessory delay ...133AdvanceTrac ...293Air cleaner filter .

LATCH ...235recommendations ...229Child safety seats - boosterseats ...

change oil soon warning,message center ...373checking and adding ...373dipstick ...373

Illuminated visor mirror ...128Infant seats(see Safety seats) ...231Inspection/maintenance (I/M)testing ...

Oil (see Engine oil) ...373PParental MyKeyprogramming ...177Parking brake ...292Part

Satellite Radio Information ...67Seats ...183child safety seats ...231cleaning ...

Press and hold REW to manuallyreverse in a CD/MP3 track.Press and hold FF to manuallyadvance in a CD/MP3 track.While in folder mode, pressFOLDER to ac

VVehicle Identification Number(VIN) ...407Vehicle loading ...268Ventilating your vehicle

AM/FM single CD/MP3 satellite compatible sound system(if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and

Satellite radio is available only with a valid SIRIUS radiosubscription. Check with your authorized dealer for availability.2. (Phone): Press to acces

• DELETE SONG: Press OK to delete a song from the system’smemory. Press/ to cycle through the saved songs. When thesong appears in the display that yo

RBDS: Available only in FM mode. This feature allows you to displaytext transmitted by RBDS-equipped stations and to search for a certaincategory of m

Adjust 1–7: Increasing this setting from 1 (lowest setting) to 7 (highestsetting) allows the radio volume to automatically change slightly withvehicle

In satellite radio mode (if equipped), press SEEK, SEEK toseek to the previous/next channel.In CATEGORY MODE, pressSEEK, SEEK to select a category(Jaz

9. FOLDER: In folder mode,pressFOLDER to access theprevious folder on MP3 discs, ifavailable.10. FF (Fast forward): In CDmode, press FF to manually ad

Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti

In satellite radio mode (if equipped), press and release to enterTEXT MODE and display the current song title. While in TEXT MODE,press again to scrol

Premium AM/FM in-dash six CD/MP3 satellite compatible soundsystem (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol,

Satellite radio is available only with a valid SIRIUS radiosubscription. Check with your authorized dealer for availability.2. (Phone): Press to acces

• DELETE SONG: Press OK to delete a song from the system’smemory. Press/ to cycle through the saved songs. When thesong appears in the display that yo

To activate, press MENU repeatedly until RBDS (ON/OFF) appears inthe display. Use/ / SEEK to toggle RBDS ON/OFF. (WhenRBDS is OFF, you will not be abl

Recommended level is 1–3; SPEED OFF turns the feature off and level 7is the maximum setting.Track/Folder Mode: Available only on MP3 discs in CD mode.

In CATEGORY MODE, press / to select a specific category(Jazz, Rock, News, etc.). Once the desired category is in the display,pressSEEK, SEEK to seek t

10. FF (Fast forward): In CDmode, press FF to manually advancein a track.In DVD mode (if equipped), press to advance within the current chapter.11. RE

14. AM/FM: Press to selectAM/FM1/FM2 frequency band.15. ON/OFF/Volume: Press to turnON/OFF. Turn to increase/decreasevolume.Note: If the volume is set

19. CD slot: Insert a CD label sideup.Auxiliary input jack (Line in)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident a

Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance

2. Ensure that the battery in your portable music player is new or fullycharged and that the device is turned off.3. Attach one end of the audio exten

USB port (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdriver

1. MEDIA: Push repeatedly to cyclethrough available playing mediassuch as AM, FM1, FM2, CD, SAT1,SAT2, SAT3 (satellite radio ifequipped), DVD (if equi

Parental controlPress the memory preset controls 3and 5 simultaneously on the frontaudio controls to disable the rearseat controls. They will remain d

Using headphones/Dual Play modeWARNING: Do not leave children unattended in the vehicle anddo not let children operate the system while unsupervised.

CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m

DATA RECORDINGService Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehi

Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The

Your vehicle may be equipped with a Family Entertainment System(FES) which allows you to listen to audio CDs, MP3 discs, watch DVDsand to plug in and

Note (navigation-based radiosystems only): Whenadiscisinserted, the FES switches todual-play mode–rear speakers turn off, and headphones turn on. Tosw

Note (navigation-based radiosystems only): Whenadiscisinserted, the FES switches todual-play mode–rear speakers turn off, and headphones turn on. Tosw

3. Connect an auxiliary audio/videosource by connecting RCA cords(not included) to the RCA jacks onthe left hand side of the system.• Yellow (1) — vid

4. Press MEDIA to change the audio source of the active channel (A orB). The audio source will be shown on the display. You may change theactive chann

Using wired headphones (not included):WARNING: Do not leave children unattended in the vehicle anddo not let children operate the system while unsuper

DVD player controls1. Headphone control A/B: Whilein Dual Play mode, press to selecteither the A or B headphone source.Then press MEDIA to select thed

4. (Fast forward): Press andrelease for the next chapter ortrack. Press and hold to forwardsearch a DVD, Video CD, or FES CD in DVD/CD mode.5./ (Play/

11. / (Headphones/Speakers): Press once for Dual Play(Headphone mode- the rear speakers are muted) and press again forSingle Play (same media playing

To access this information, special equipment must be directlyconnected to the recording modules. Ford Motor Company andFord of Canada do not access e

Remote controlUnless otherwise stated, all operations can be carried out with theremote control. Always point the remote control directly at the playe

7. VOL (Volume): When in Single Play, press to increase ( )ordecrease () the volume over all speakers. When in Dual Play, press toincrease () or decre

21. LANGUAGE (DVD dependent): Press to select the desiredlanguage.22. ENTER: Press to select the highlighted menu option.23. ILLUMINATION: Press to il

HeadphonesWireless headphonesWARNING: The driver should never use the headphones whiledriving the vehicle. Using headphones may prevent the driverfrom

To install the batteries, remove the screw at the bottom of the cover.Then, lightly press down on top and slide the cover off.When replacing the batte

To operate the headphones:• Press POWER on the ear piece to turn on the headphones. A redindicator light will illuminate indicating the headphones are

Wired headphonesWARNING: Do not leave children unattended in the vehicle anddo not let children operate the system while unsupervised. Ifwired headpho

Single Play: Single play consists of all occupants in the vehicle listeningto the same playing media over the front and rear speakers. When theDVD sys

Press the Headphone Control buttonA to change the audio source forChannel A.Press MEDIA to change the audiosource for Channel A. Thisinformation will

Press the Headphone Control buttonA to change the audio source forChannel A.Press MEDIA to change the audiosource for Channel A. Thisinformation will

WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers use extreme caution

Menu modePress MENU once on the DVD system to access the DVD disc menu ifavailable.Press MENU twice to access the DVD set-up menu and the followingfea

You can select from: WIDE, LETTERBOX or PAN SCAN. Once you havemade your selection, press ENTERto confirm. The LCD screen displaywill immediately chan

Once you have made your selection,press ENTER to confirm. This isdisc dependent.Audio CDsTo play audio CDs on your DVD system:1. Ensure that the vehic

4. The folder, track and elapsedtime will appear in the status bar.The screen will list the Artist, Title,Album and File Name.COMP (Compression):Compr

CD, MP3 and CD player care• Handle discs by their edges only. Never touch the playing surface.• Do not expose discs to direct sunlight or heat sources

Playing a DVD1. Ensure that the vehicle is on or the ignition is in accessory mode.2. Ensure that the navigation system is on.3. Insert a DVD label-si

Frame by frame1. With a DVD playing, press pause.2. Press the right cursor button. TheDVD will advance one frame. Eachpress of the right cursor button

The B headphone jack (5) is locatedon the right side of the DVD system.Plug in wired headphones (notincluded) here.Note: The B headphones can onlyacce

There are three levels of control ofthe FES buttons. The states areFULL (enabled), LOCAL orLOCKED (disabled). To change the level of control, press th

rights owners. Use of this copyright protection technology must beauthorized by Macrovision Corporation, and is intended for home andother limited vie