Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Message center 19Entertainment Systems 28AM/FM stereo with CD/MP3 28Auxiliary
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
• the driver door is opened within 10 minutes of the ignition beingtransitioned to the off or accessory position.Note: The doors will not autounlock i
3. Enter factory–set 5–digit entry code.4. Press and hold the 3 • 4. While holding the 3 • 4, press and releasethe 7 • 8. While still holding the 3 •
the following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including i
One step door unlockingIf the one step door unlocking feature is activated, pressand releaseonce to unlock all of the doors, the liftgate and liftgate
Replacing the batteryThe Integrated Keyhead Transmitter uses one coin type three-voltlithium battery CR2032 or equivalent.To replace the battery:1. Tw
The illuminated entry system will turn off the lights if:• the ignition is turned to the on position, or• the Integrated Keyhead Transmitter lock cont
2. Within five seconds press the 1 • 2 on the keypad. The doors will lockand then unlock to confirm that the system is in programming mode.3. Enter yo
Unlocking and locking the doors and liftgate using keyless entryTo unlock the driver’s door, enter the factory set 5-digit code or yourpersonal code.
Anti-theft indicatorThe anti-theft indicator is located in the instrument panel cluster.• When the ignition is in the offposition, the indicator will
keyless entry transmitter. A maximum of eight coded keys can beprogrammed to your vehicle; only four of these eight keys can be IKTswith remote entry
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
4. After three seconds but within 10 seconds of turning the ignition tothe 1 (off) position, insert the second previously coded key into theignition.5
FRONT SEATSWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the eve
To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o
To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous
WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting the front manual seat (if eq
WARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event of a col
Press the control to move the seatforward, backward, up or down.Heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbeca
WARNING: To minimize the risk of neck injury in the event of acrash, the driver and passenger occupants should not sit inand/or operate the vehicle, u
Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as possible to theba
To reinstall the adjustable head restraint, do the following:1. Insert the two stems into theguide sleeve collars.2. Push the head restraint downuntil
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
3. Flip seat forward.Attach the safety belt web snapbutton to the quarter trim panelsnap button. This will ensure thatsafety belt does not get caught
5. Rotate seatback down into loadfloor position.Returning the second row seats to upright position1. Pull seatback up and into uprightposition making
WARNING: Make sure safety belt buckle heads are throughelastic holders on seat backs. Safety belt buckles may break ifthey are trapped underneath the
To install the second row cushion1. Push the cushion to the inboardside of the vehicle.2. Make sure that the hinges arelocked into place.SAFETY RESTRA
conditions. A collection of crash and occupant sensors providesinformation to the Restraints control module (RCM). During a crash, theRCM may activate
occupant is not properly restrained by safety belts or child safety seatsand they move forward during pre-crash braking. The most effective wayto redu
increase the effectiveness of the safety belts. In frontal collisions, thesafety belt pretensioners can be activated alone or, if the collision is ofs
WARNING: To reduce the risk of injury, make sure children sitwhere they can be properly restrained.WARNING: Never let a passenger hold a child on his
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
(8 km/h) or more, the combination safety belts will lock to help reduceforward movement of the driver and passengers.Automatic locking modeWhen to use
bulbs work. If any light remains on after starting the vehicle, refer to therespective system warning light for additional information.Service engine
How to disengage the automatic locking modeDisconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic l
The safety belt pretensioners activate during frontal collisions, and inside collisions and rollovers. A safety belt pretensioner is a device whichtig
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war
If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the onposition or less than1-2 minutes h
Reasons given... Consider...⬙Belts areuncomfortable⬙Your Ford safety belts are designed to enhancecomfort. If you are uncomfortable - try differentpos
Deactivating/activating the Belt-Minder姞 featureThe driver and front passenger Belt-Minder威 aredeactivated/activated independently. When deactivating/
4. Within approximately seven seconds of the light turning off, bucklethen unbuckle the safety belt.• This will disable the Belt-Minder威 feature for t
WARNING: All occupants of the vehicle, including the driver,should always properly wear their safety belts, even when an airbag supplemental restraint
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
Brake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the on
impact sensors, the system wiring, the airbag system readiness light, theairbag back up power and the airbag ignitors).WARNING: Several air bag system
The front passenger sensing systemuses a ⬙passenger airbag off⬙ or⬙pass airbag off⬙ indicator which willilluminate and stay lit to remind youthat the
• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LampPasseng
ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase,
In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi
A difficulty with the system is indicated by one or more of the following:• The readiness light will eitherflash or stay lit.• The readiness light wil
How does the side airbag system work?The design and development of theside airbag system includedrecommended testing proceduresthat were developed by
WARNING: Several airbag system components get hot afterinflation. Do not touch them after inflation.WARNING: If the sideairbag has deployed, theairbag
Safety Canopy姞 SystemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a deploying
How does the Safety Canopy姞 System work?The design and development of theSafety Canopy威 System includedrecommended testing proceduresthat were develop
Charging system: Illuminates whenthe battery is not charging properly.If it stays on while the engine isrunning, there may be a malfunctionwith the ch
The Safety Canopy威 is mounted to roof side-rail sheet metal, behind theheadliner, above the first and second row seats. The Safety Canopy威 isdesigned
If any of these things happen, even intermittently, have the SRS servicedat your authorized dealer immediately. Unless serviced, the system maynot fun
Important child restraint precautionsWARNING: Always make sure your child is secured properly ina device that is appropriate for their height, age and
Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfantsortoddlersChildren weighing 40 lb
• When possible, always properly restrain children twelve (12) years ofage and under in a rear seating position of your vehicle. Accidentstatistics su
WARNING: Always carefully follow the instructions andwarnings provided by the manufacturer of any child restraint todetermine if the restraint device
training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertifi
Airbags can kill or injure a child in a child seat. NEVER place arear-facing child seat in front of an active airbag. If you must use aforward-facing
Perform the following steps when installing the child seat withcombination lap/shoulder belts:Note: Although the child seat illustrated is a forward f
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
Overdrive cancel and gradeassist: Illuminates when theoverdrive function of thetransmission has been turned offand the grade assist function hasbeen t
8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up
method eliminates the need to use safety belts to attach the child seat,however the safety belt can still be used to attach the child seat. Forforward
WARNING: Depending on where you secure a child restraint,and depending on the child restraint design, you may blockaccess to certain safety belt buckl
Combining safety belt and LATCH lower anchors for attachingchild safety seatsWhen used in combination, either the safety belt or the LATCH loweranchor
2. Locate the correct anchor for theselected seating position.There are three tether anchorslocated on the headliner at the rearof the vehicle.3. Clip
around four (4) years of age. Consult your child safety seat owner guidefor the weight, height, and age limits specific to your child safety seat.Keep
• Is the shoulder belt centered on the shoulder and chest?• Can the child stay seated like this for the whole trip?Types of booster seatsThere are gen
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
GAUGESStandard instrument cluster gaugesOptional instrument cluster gaugesInstrument Cluster172010 Escape (204)Owners Guide, 2nd PrintingUSA (fus)
Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary
• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and
government test course. For example, a tire graded 150 would wear oneand one-half (11⁄2) times as well on the government course as a tiregraded 100. T
• Tire Identification Number (TIN): A number on the sidewall ofeach tire providing information about the tire brand andmanufacturing plant, tire size
At least once a month and before long trips, inspect each tire and checkthe tire pressure with a tire gauge (including spare, if equipped). Inflateall
To check the pressure in your tire(s):1. Make sure the tires are cool, meaning they are not hot from drivingeven a mile.If you are checking tire press
the valve stem. Inspect the tire sidewalls for cracking, cuts, bruises andother signs of damage or excessive wear. If internal damage to the tire issu
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w
• Do not run over curbs or hit the tire against a curb when parkingWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the
Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,
Tire rotationRotating your tires at the recommended interval (as indicated in thescheduled maintenance information that comes with your vehicle) willh
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can b
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including inter
To restore the full functionality of the Tire Pressure Monitoring System,have the damaged road wheel/tire repaired and remounted on yourvehicle. For a
Tachometer: Indicates the enginespeed in revolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the
Low Tire PressureWarning LightPossiblecauseCustomer Action RequiredFlashing WarningLightSpare tire inuseYour temporary spare tire is inuse. Repair the
SNOW TIRES AND CABLESWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel
VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the
to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400
Locks and Security 92Keys 92Locks 97Anti-theft system 107Seating and Safety Restraints 111Seating 111Safety restraints 123Airbags 136Child restraints
InfoPress the INFO button repeatedly tocycle through the following features:TRIP A/BRegisters the distance of individual journeys. Press and release I
TRAILER TOWINGTrailer towing with your vehicle may require the use of a trailer towoption package.Trailer towing puts additional loads on your vehicle
4x2GCWR (Gross Combined Weight Rating)/Trailer WeightsEngine MaximumGCWR - lb(kg)Trailer WeightRange - lb (kg)Maximumfrontal area oftrailer - ft2(m2)2
4x4GCWR (Gross Combined Weight Rating)/Trailer WeightsEngine MaximumGCWR - lb(kg)Trailer WeightRange - lb (kg)Maximumfrontal area oftrailer - ft2(m2)2
Safety chainsAlways connect the trailer’s safety chains to the hook retainers on thevehicle. To connect the trailer’s safety chains, cross the chains
• To eliminate excessive shifting, use a lower gear. This will also assistin transmission cooling. For additional information, refer to Automatictrans
Exceeding these limits may allow water to enter vehicle components:• causing internal damage to the components.• affecting driveability, emissions and
• For vehicles equipped with an automatic transmission, start the engineand allow it to run for five minutes at the beginning of each day andevery six
STARTINGPositions of the ignition1. Off— locks the gearshift leverand steering column and allows keyremoval.2. Accessory— allows the electricalaccesso
WARNING: If you smell exhaust fumes inside your vehicle, haveyour dealer inspect your vehicle immediately. Do not drive if yousmell exhaust fumes.Impo
• Make sure the gearshift is in P(Park).If starting a vehicle with a manualtransmission:• Make sure the parking brake isset.• Press and hold the clutc
• Differences in the automatic shut-off points on the fuel pumps atservice stations• Variations in top-off procedure from one fill-up to another• Roun
Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrument Cluster chapter for more informationregarding the warning
Do not crank the engine for more than 10 seconds at a time as starterdamage may occur. If the engine fails to start, turn the key to off andwait 30 se
the user to connect the system to a grounded 120 volt A/C electricalsource. The block heater system is most effective when outdoortemperatures reach b
become very hot and may result in an electrical shock or fire. Be sureto check for heat anywhere in the electrical hookup once the systemhas been oper
keeping the brakes from locking. Noise from the ABS pump motor andbrake pedal pulsation may be observed during ABS braking and thebrake pedal may sudd
The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned on) until theparking brake is released.
ADVANCETRAC姞 WITH ROLL STABILITY CONTROL™ (RSC姞)STABILITY ENHANCEMENT SYSTEMWARNING: Vehicle modifications involving braking system,aftermarket roof r
The AdvanceTrac威 with RSC威 system provides the following stabilityenhancement features for certain driving situations:• Traction Control (TCS), which
• If the driving condition is severe and your foot is not on the brake, thebrake pedal may move as the systems applies higher brake forces. Youmay als
Certain adverse driving maneuvers may activate the Electronic StabilityControl system, which include but are not limited to:• Taking a turn too fast•
1. OIL LIFE2. LIFTGATE AND GLASS3. BRAKE SYSTEM4. DTE/FUEL LEVEL5. PARK AID (if equipped)6. MYKEY DISTANCE (if a MyKey™ is programmed)7. MYKEY(S) PROG
AdvanceTrac威 with RSC威 FeaturesButtonfunctions“Slidingcar”iconRSC威 ESCTractionControlDefault atstart-upIlluminatedduring bulbcheckEnabled Enabled Enab
Disabling trailer sway controlTrailer sway control can be disabled during any key cycle. Pressing andholding the AdvanceTrac威 with RSC威 button for mor
PREPARING TO DRIVEWARNING: Utility vehicles have a significantly higher rolloverrate than other types of vehicles.WARNING: In a rollover crash, an unb
If the fuse is not blown, perform the following procedure:1. Apply the parking brake, turn the ignition to off, then remove the key.2. Using a screwdr
provide consistent shift feel over the life of the vehicle. A new vehicle ortransmission may have firm and/or soft shifts. This operation isconsidered
N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D
O/D (overdrive mode) is automatically returned each time the engine isturned off.L (Low)• Provides maximum engine braking.• Will downshift to the lowe
Failure to fully press the clutch pedal to the floor may causeincreased shift efforts, prematurely wear transmissioncomponents or damage the transmiss
Parking your vehicle1. Apply the brake and shift into the neutral position.2. Fully apply the parking brake, then shift into 1 (First).3. Turn the ign
The RSS detects obstacles up to6 feet (1.8 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the
Press the RESET control to select the new Autolamp delay values of 0,10, 20, 30, 60, 90, 120 or 180 seconds.AUTOLOCKThis feature automatically locks a
REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rearview camera system locatedon the liftgate provides a videoimage, which appears in therearview mirror or on
Note: The default setting for the camera delay is off. Press the“Settings” button found on the navigation screen (if equipped) to set thecamera delay
Servicing• If the image comes on while the vehicle is not in R (Reverse), havethe camera inspected by your authorized dealer.• If the image is not cle
For best performance, the driver should drive the vehicle as parallel aspossible while passing a parking space. If driven too fast (above 18 mph[30 km
When you determine the vehicle is back far enough or you hear a solidtone from Reverse Sensing System, bring the vehicle to a complete stopand move th
• Exceeding a vehicle speed of 6 mph (10 km/h) during automaticsteering• Deactivating the AdvanceTrac威 system or the system has activated ona slippery
Why doesn’t APA position the vehicle where I want in the space?• The driver allows the vehicle to roll in the opposite direction of thetransmission (s
BLIND SPOT MIRRORSBlind spot mirrors have anintegrated convex spotter mirrorbuilt into the upper outboard cornerof the outside mirrors. They aredesign
FOUR WHEEL DRIVE (4WD) SYSTEM (IF EQUIPPED)WARNING: For important information regarding safe operationof this type of vehicle, see Preparing to drive
If your vehicle goes off the edge of the pavement• If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ea
The message center will display the last selected feature if there are nomore warning messages.Types of messages and warnings:• Some messages will app
WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your author
Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required f
Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should
Driving on snow and ice4WD vehicles have advantages over 2WD vehicles in snow and ice butcan skid like any other vehicle.Should you start to slide whi
Maintenance and ModificationsThe suspension and steering systems on your vehicle have been designedand tested to provide predictable performance wheth
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co
Note: With extended use, the flasher may run down your battery.FUEL PUMP SHUT-OFF SWITCHThis device stops the electric fuel pump from sending fuel to
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Not used (spare)2 15A Brake on/off switch3 15A SYNC威 module4 30
LOW TIRE PRESSURE — Displayed when one or more tires on yourvehicle have low tire pressure. Refer to Inflating your tires in the Tires,Wheels and Load
Fuse/RelayLocationFuse AmpRatingProtected Circuits15 10A Climate control16 15A Not used (spare)17 20A All lock motor feeds, Liftgaterelease, Liftglass
Fuse/RelayLocationFuse AmpRatingProtected Circuits41 15A Driver/passenger door lockswitches, Automatic dimmingmirror, Compass, Ambientlighting, Moon r
WARNING: To reduce risk of electrical shock, always replacethe cover to the Power Distribution Box before reconnecting thebattery or refilling fluid r
Fuse/RelayLocationFuse AmpRatingProtected Circuits8 20A* Trailer tow parking lamps9 50A** Anti-lock brake system (ABS)10 30A** Front wipers11 30A** St
Fuse/RelayLocationFuse AmpRatingProtected Circuits30D — Cooling fan 2 relay31A — Reverse lamp relay31B — Not used31C — Trailer tow left turn relay31D
WARNING: The use of tire sealants may damage your tirepressure monitoring system and should not be used.WARNING: Refer to Tire pressure monitoring sys
Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following:• Handling, stability and braki
Stopping and securing the vehicle1. Park on a level surface, set theparking brake and activate hazardflashers.2. Place gearshift lever in P (Park)(aut
Remove the lug wrench from thejack in order to remove the sparetire from under the vehicle.Removing the spare tire or spare tire and tether (if equipp
5. Use the lug wrench to remove thelug nut from the spare tire tether.6. If not replacing the spare or flattire to the underbody storage area,raise wi
TOP SPEED MYKEY SETTING — Displayed when a MyKey™ is inuse and the MyKey speed limit is on and the vehicle speed is 80 mph(130 km/h). Refer to MyKey™
WARNING: Do not attempt to change a tire on the side of thevehicle close to moving traffic. Pull far enough off the road toavoid the danger of being h
Before placing the jack under the vehicle, NOTE the jack locations:• FrontView shown from rear of front tire.Position the jack directly below theprotr
• RearView shown from forward of reartire. Position the jack directly belowthe stud on the rear trailing arm.3. Position the jack according to theguid
Never use the differentials as ajacking point.WARNING: To lessen therisk of personal injury, donot put any part of your bodyunder the vehicle while ch
Stowing the jack and tools• Make sure the jack is fullylowered.• Reclip the tools onto the jackmaking sure that the tools arefully contained by the cl
spare tire carrier has a built-in ratchet feature that will not allow you toovertighten. If the spare tire carrier ratchets with very little effort, t
Note: Inspect the wheel pilot holeprior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean r
Preparing your vehicleWhen the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto
SPACE FOUND STOP (if equipped) — May display when using theactive park assist system. See Active park assist in the Driving chapterfor more informatio
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized
• Service specials and promotions.In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2
In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext
procedure outlined on the first page of the Customer Assistance section,you may be eligible to participate in the BBB AUTO LINE program.The BBB AUTO L
The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have
If you are in another foreign country, contact the nearest authorizeddealer. If the authorized dealer employees cannot help you, they candirect you to
AUDIO SYSTEMSNote: If your volume is muted and MYKEY VOLUME LIMITED isdisplayed, refer to MyKey™ in the Locks and Security chapter for moreinformation
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i
WAXING• Wash the vehicle first.• Do not use waxes that contain abrasives; use Motorcraft威 PremiumLiquid Wax (ZC-53-A), which is available from your au
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
3.0L V6 ENGINEPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authorized
• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft威 Premium Windshield Washer Concentrate (ZC-32-A),available from your a
If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows:1. Wipe up spilled liqui
LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• For routine cleaning, wipe the surface wit
Motorcraft威 Premium Glass Cleaner (Canada only) (CXC-100)Motorcraft威 Premium Liquid Wax (ZC-53-A)Motorcraft威 Premium Windshield Washer Concentrate (U.
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
AM/FM Radio/ VOL (Power/Volume): Pressto turn the radio on/off. Turn theknob to increase/decrease volume.If the volume is set above a certainlevel and
Working with the engine on1. For vehicles equipped with an automatic transmission, set the parkingbrake and shift to P (Park). For vehicles equipped w
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.5L I4 engine1. Engine coolant reservoir2. Engine oil filler cap3. Automatic transmission dipstick (i
3.0L V6 engine1. Engine coolant reservoir2. Air filter assembly3. Brake fluid reservoir4. Automatic transmission fluid dipstick5. Power distribution b
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
CHANGING THE WIPER BLADES1. Pull the wiper blade and armaway from the glass.2. Squeeze the locking tabs torelease the blade from the arm andpull the b
To replace the wiper blade:1. Grab the wiper arm with onehand close to the arm/blade jointand pull it as far away from theglass as possible. Do not us
• 2.5L I4 engine• 3.0L V6 engine6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil level is within the lower and
• 3.0L V6 engine• If required, add engine oil to the engine. Refer to Adding engine oilin this chapter.• Do not overfill the engine with oil. Oil leve
Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by th
BATTERYYour vehicle is equipped with aMotorcraft威 maintenance-freebattery which normally does notrequire additional water during itslife of service.If
Customer Assistance 274Reporting safety defects (U.S. only) 280Reporting safety defects (Canada only) 280Cleaning 281Maintenance and Specifications 28
To activate the autoset feature: Press MENU repeatedly until AUTOPRESET ON/OFF appears in the display. UseSEEK/TRACK toturn AUTO PRESET ON, and either
WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
• Refer to scheduled maintenance information for service intervalschedules.If the engine coolant has not been checked at the recommended interval,the
• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcoholand other liquids can cause en
Whenever coolant has been added, the coolant level in the coolantreservoir should be checked the next few times you drive the vehicle. Ifnecessary, ad
• NEVER decrease the coolant concentration below 40%.Decreased engine coolant concentrations below 40% willdecrease the corrosion/freeze protection ch
operation and the engine will run rough. Remember that the engine iscapable of completely shutting down automatically to prevent enginedamage, therefo
Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforefueling your vehicle.• Alwa
Pure ethanol is the alcohol which is the intoxicating agent in liquor, beerand wine. It is distilled from the fermentation of plants such as field cor
RefuelingWARNING: Fuel vapor burns violently and a fuel fire can causesevere injuries. To help avoid injuries to you and others:• Read and follow all
/ Play/Pause: Press toplay/pause a track when playing aCD.SEEK/TRACK: PressSEEK/TRACK to access theprevious/next track.CAT (Category) / FOLD (Folder):
Note: A fuel spillage concern may occur if overfilling the fuel tank. Donot overfill the tank to the point that the fuel is able to bypass the fuelfil
Choosing the right fuelIf your vehicle is a flexible fuel vehicle (FFV), use only UNLEADEDFUEL and FUEL ETHANOL (Ed75–Ed85).If your vehicle is not a f
If you operate your vehicle 50% or more of the time on ethanol, youshould follow a different maintenance schedule. In addition to this, if youexclusiv
• The service engine soon indicator may come on. For moreinformation on the service engine soon indicator, refer to Warninglights and chimes in the In
2. Slowly insert the funnel into theEasy Fuel™ system.3. Fill the vehicle with fuel from the portable fuel container.4. When done, clean the funnel or
vehicle after the fuel gauge indicates empty, you might not beable to refuel the full amount of the advertised capacity of thefuel tank due to the emp
Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin
• Adding certain accessories to your vehicle (for example bugdeflectors, rollbars/light bars, running boards, ski racks) may reducefuel economy.• Usin
WARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine compartment and exhaus
4. Driving through deep water—the electrical system may be wet.These temporary malfunctions can be corrected by filling the fuel tankwith good quality
SHUFFLE: Press SHUFFLE to switch on/off and begin/stop random play.The system will only shuffle the disc currently playing.Satellite Radio (if equippe
The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not
during hot weather or pulling a trailer, the vehicle should beturned off for about 30 minutes to allow fluid to cool beforechecking.1. Drive the vehic
Type AType BThe transmission fluid should be in the zone, identified by the arrows inthe above figures, if at normal operating temperature 185°F-200°F
Use of a non-approved automatic transmission fluid may causeinternal transmission component damage.If necessary, add fluid in 1/2 pint (250 ml) increm
This fluid level is within the normal operating fluid range and does notrequire that you have your fluid level readjusted after recreational flattow o
1. Release the clamps that secure the air filter housing cover.• 2.5L I4 engine• 3.0L V6 engine2. Pull the air filter housing cover away.3. Remove the
MOTORCRAFT PART NUMBERSComponent 2.5L I4 engine 3.0L V6 engineAir filter element1FA-1772 FA-1893BatteryBXL-40R/BXT-96R 5903BXL-40R/BXT-96R 5903Oil fil
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord part name orequivalentFord part number /Ford SpecificationBrake fluid and (clutchfl
Item CapacityFord part name orequivalentFord part number /Ford SpecificationEngine oil(2.5L engine)5.3 quarts(5.0L)•Motorcraft威 SAE 5W-20Premium Synth
Item CapacityFord part name orequivalentFord part number /Ford SpecificationManual transmissionfluid2.4 quarts (2.3L)8Motorcraft威 SAE 75W-90Gear OilXT
MEMORY PRESETS (0–9): Thereare 30 available presets, 10 each forSAT1, SAT2 and SAT3. To savesatellite channels in your memorypresets, tune to the desi
ENGINE DATAEngine 2.5L I4 engine 3.0L V6 engineCubic inches 152 183Required fuel 87 octane 87 octane or E85Firing order 1-3-4-2 1-4-2-5-3-6Ignition sy
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
Peace of mindKeyless entry keypadRemote start systemVehicle security systemWheel locksFor maximum vehicle performance, keep the following information
FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on
Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With
Ford Extended Service Plan3372010 Escape (204)Owners Guide, 2nd PrintingUSA (fus)
AAccessory delay ...72Active Park Assist ...232AdvanceTrac ...216Air cleaner filte
Child safety seats ...156attaching withtether straps ...163in front seat ...157in
an audible prompt. Press OK while SONG ALERT is in the display andthe system will take you to the channel playing the desired song. Youcan save up to
coolant ...301fail-safe cooling ...305idle speed control ...299lubrication speci
IIgnition ...207, 330Illuminated visor mirror ...67Infant seats(see Safety seats) ...156Inspec
OOctane rating ...311Oil (see Engine oil) ...295Overdrive ...223PParental MyKe
SecuriCode keyless entrysystem ...105SecuriLock passive anti-theftsystem ...
WWarning lights (see Lights) ...12Washer fluid ...293Water, Driving through ...244Windowspower ...
Note: you must be tuned to the specific channel you want tolock/unlock when using this feature.b. CHANGE PIN: Press OK when CHANGE PIN is displayed. T
ALL SEATS (Occupancy mode, if equipped): Press SOUNDrepeatedly to reach the Occupancy mode setting. PressSEEK/TRACK to select and optimize sound for A
Your vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicplayer to the in-vehic
7. Adjust the sound on your portable music player until it reaches thelevel of the FM station or CD by switching back and forth between theAUX and FM
Your vehicle may be equipped with aUSB port located on the instrumentpanel. This feature allows you toplug in media playing devices,memory sticks, and
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C
CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required. Thism
Radio Display Condition Action RequiredNO SIGNAL Loss of signal from theSIRIUS威 satellite orSIRIUS威 tower to thevehicle antenna.You are in a location
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1.Fan speed adjustment: Turn to select fan speed.2.RRear defroster: Press to activate/deactivat
9. Temperature control: Controls the temperature of the airflow in thevehicle.10.Passenger heated seat control (if equipped): Press toactivate/deactiv
Operating tips• To reduce fog build up on the windshield during humid weather,select(defrost) or (floor/defrost).• To reduce humidity build up inside
DUAL AUTOMATIC TEMPERATURE CONTROL (IF EQUIPPED)1. AUTO/Driver temperature: Press to engage full automaticoperation. Select the desired temperature us
Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti
the vehicle through the vents. Turn to manually increase/decrease thefan speed. The manual fan speed setting will appear on the left side ofthe displa
14. Driver heated seat control (if equipped): Press toactivate/deactivate the driver heated seat. See Heated seats in theSeating and Safety Restraints
• Manual operation:1. Select MAX A/C.2. Selector .3. Select(recirculated air) to provide colder airflow.4. Set the temperature to 60°F (16°C).5. Set h
HEADLAMP CONTROLRotate the headlamp control to thefirst positionto turn on theparking lamps.Rotate to the second positiontoturn on the headlamps.Rotat
2. Rotate the headlamp control to the autolamp position.3. Rotate the headlamp control to the off position.4. Turn the key to the on position.5. Turn
Flash-to-passPull toward you slightly to activateand release to deactivate.Daytime running lamps (DRL) (if equipped)Turns the lowbeam headlamps on wit
switch from the full dim position to the full dome/on position to reset.This will ensure that your displays are visible under all lightingconditions.A
5. Locate the vertical adjuster onthe headlamp, then turn theadjuster either clockwise (to adjustup) or counterclockwise (to adjustdown) aligning the
The map lamp controls (withoutmoon roof) are located on the domelamp. Press the button on eitherside of each map lamp to illuminatethe lamps. Press th
Ambient lighting (if equipped)Illuminates footwells, cupholders,the console bin and the console traywith a choice of several colors. Theambient lighti
Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance
Take your vehicle to dealer for service if any of the above conditions ofunacceptable moisture are present.Using the right bulbsReplacement bulbs are
Replacing headlamp bulbs1. Make sure the headlamp control is in the off position.2. Open the hood.3. Reach over the front bolster.4. Remove the bulb b
5. Carefully pull the bulb out of thesocket and push in the new bulb.6. Install the bulb socket into thelamp assembly and rotate clockwise.Replacing f
Replacing high-mount brake lamp bulbs1. Remove the two screws and movethe lamp assembly away from theliftgate.2. Remove the bulb holder from thelamp a
Replacing license plate lamp bulbs1. Make sure the headlamp switch isin the off position.2. Press the lever and carefully prythe license plate lamp as
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
Rear window wiper/washer controlsFor rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select:2 — Normal spe
ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamps.Slide-on-rod featureThe visor will slide back and forthon
The compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antenna. Magneticor metallic objec
6. The direction will display afterthe RESET control is released. Thezone is now updated.Compass calibration adjustmentPerform compass calibration in
Using your vehicle as an ambulanceDo not use this vehicle as an ambulance.Your vehicle is not equipped with the Ford Ambulance PreparationPackage.DATA
5. Small storage trays and (if equipped) an ambient light control switch.WARNING: Use only soft cups in the cupholders. Hard objectscan injure you in
To prevent the fuse from being blown, do not use the power point(s)over the vehicle capacity of 12 VDC/180W. If the power point or cigarlighter socket
One-touch down (AUTO)Allows the driver’s window to openfully without holding the controldown. Press the switch completelydown to the second detent and
Do not block the sensors on the front and back of the interiorrear view mirror since this may impair proper mirrorperformance.Do not clean the housing
Fold-away mirrorsFold the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.Heated outside mirrors(if equipped)B
Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas
Resuming a set speedPress the RES control and releaseit. This will automatically return thevehicle to the previously set speed.Increasing speed while
Turning off speed controlThere are two ways to turn off thespeed control:• Press the OFF control.• Turn off the ignition.Note: When you turn off the s
In any mode:• Press VOL + or VOL - to adjustthe volume.Navigation system hands freecontrol features (if equipped)Press and holdcontrol brieflyuntil th
Navigation system/SYNC威 handsfree control features (ifequipped)Presscontrol briefly until thevoiceicon appears on theNavigation display to use the voi
Ford of Canada do not access event data recorder informationwithout obtaining consent, unless pursuant to court order orwhere required by law enforcem
Bounce-back: When an obstacle has been detected in the moon roofopening as the moon roof is closing, the moon roof will automaticallyopen and stop at
Car2U姞 Home Automation System (if equipped)The Car2U威 Home AutomationSystem is a universal transmitterlocated in the driver’s visor thatincludes two p
• Fixed code garage door openers were produced prior to 1996. Fixedcode uses the same coded signal every time. It is manuallyprogrammed by setting DIP
2. Go to the garage to locate thegarage door opener motor and its“learn” button. You may need aladder to reach the unit and youmay need to remove the
the Erasing the Car2U威 Home Automation System buttons procedureand then programming all of the devices being used.Fixed code programmingNote: Do not p
3. To input these positions into theCar2U威 system, simultaneouslypress all three Car2U威 systembuttons for a few seconds and thenrelease to put the dev
To erase programming on the Car2U威 system (individual buttons cannotbe erased), use the following procedure:1. Firmly press the two outsideCar2U威 syst
Do not open the liftgate or liftgate window in a garage or other enclosedarea with a low ceiling. If the liftgate window is raised and the liftgate is
WARNING: Do not place any objects on the cargo area shade.They may obstruct your vision or strike occupants of vehicle inthe case of a sudden stop or
ROOF RACK SYSTEM (IF EQUIPPED)Loads should never be placed directly on the roof panel. For properfunction of the roof rack system, loads must be place
WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers use extreme caution
To remove the cross-bar assembly (if equipped) from the roof rackside rails:1. Loosen the thumbwheel at bothends of the cross-bar (bothcross-bars are
To reinstall the cross-bar assembly (if equipped) to the roof rackside rails:1. Ensure that both cross-barassemblies are installed with the F(front) a
KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unl
vehicle can be activated as a MyKey™. The key will remain restricteduntil MyKey™ is disabled. Any remaining keys are referred to as an“Administrator k
3. Press and hold the RESET button for two seconds until MARK THISAS RESTRICTED is displayed.4. Wait until KEY RESTRICTED AT NEXT START is displayed.M
4. Press and hold the RESET button for two seconds until ALL MYKEYSCLEARED is displayed.Check MyKey™ System StatusThe vehicle System Check will provid
Note: For all vehicles with remote start installed, it is possible toprogram all original vehicle keys as MyKeys™, in which case, you willneed to use
Condition Potential CausesLost any key • For programming spare keys, refer to theProgramming spare keys section in this chapter.I accidentallyprogramm
AutolockThe autolock feature will lock all the doors, liftgate and liftgate windowwhen:• all doors are closed,• the ignition is in the on position,• y
1. The ignition must be off to beginsequence.2. Turn the ignition to the onposition.3. Press the power door unlockcontrol three times.4. Turn the igni
Commentaires sur ces manuels