Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Message center 19Entertainment Systems 27How to get going 27AM/FM stereo with
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
Utility hookThe utility hook can be used tohang small items such as grocerybags, etc. Do not hang more than10 lb (4.5 kg) on the hook.ROOF RACK SYSTEM
KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the lo
POWER DOOR LOCKS• Press the control to unlock alldoors.• Press thecontrol to lock alldoors.Smart locksThis feature helps to prevent you from locking y
Deactivating/activating autolock featureYour vehicle comes with the autolock features activated; there are fourmethods to enable/disable this feature:
Keyless entry keypad autolock enable/disable procedure1. Turn the ignition to the offposition.2. Close all the doors.3. Enter factory–set 5–digit entr
Power door lock switch autounlock enable/disable procedureBefore starting, ensure the ignition is in the off position and all vehicledoors are closed.
CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the
There are two possible types of IKTs:• Vehicles equipped with a powerliftgate• Vehicles not equipped with apower liftgateThe typical operating range f
The IKT allows you to:• remotely unlock the vehicle doors.• remotely lock all the vehicle doors.• remotely open the power liftgate (if equipped).• act
Note: If any door or the liftgate is not closed, the horn will chirp twiceand the lamps will not flash.Opening the power liftgate (if equipped)Presstw
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
Activating the memory featureTo activate this feature:1. Position the seat and mirrors to the desired positions.2. Press and hold either the 1 or 2con
To replace the battery:1. Twist a thin coin in the slot of theIKT near the key ring in order toremove the battery cover.Note: Do not wipe off any grea
The illuminated entry system will turn off the interior lights if:• the ignition is turned to the on position, or• the Integrated Keyhead Transmitter
1. Place the key in the ignition and turn the ignition to the on position.2. Press the power door unlockcontrol on the door panel threetimes.3. Turn t
SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• recall memory sea
Erasing personal code1. Enter the factory set 5–digit code.2. Within five seconds, press the 1 • 2 on the keypad and release.3. Press and hold the 1 •
Your vehicle comes with two coded Integrated Keyhead Transmitters;additional coded IKTs may be purchased from your authorized dealer.Standard SecuriLo
Automatic armingThe vehicle is armed immediately after switching the ignition to the offposition.The theft indicator will flash everytwo seconds to ac
Tips:• Only use Integrated Keyhead Transmitters (IKTs) or standardSecuriLock威 keys.• You must have two previously programmed coded keys (keys thatalre
If the key has been successfully programmed it will start the vehicle’sengine and will operate the remote entry system (if the new key is anIntegrated
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A wa
SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o
To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o
To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Insert and p
WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Using the manual lumbar support (if eq
Pump the handle upwards to raisethe cushion and pump downward tolower the cushion to the desiredlocation.Pull lever up to adjust seatback.Folding down
WARNING: Cover sharp edges on the load to help preventinjury to occupants. Secure the load to help prevent shiftingduring sudden stops.WARNING: Before
WARNING: To reduce the risk of possible serious injury: Do nothang objects off seat back or stow objects in the seatback mappocket (if equipped) when
• To program position 2, repeat the previous procedure using controlbutton 2.• A chime will sound confirming that a memory position has been set.A pos
Note: Do not do the following:• Place heavy objects on the seat• Operate the seat heater if water or any other liquid is spilled on theseat. Allow the
Press the release button to lowerthe head restraint.Folding down the 60/40 rear seatsNote: The head restraints should be placed in the full down posit
WARNING: Under engine misfire conditions, excessive exhausttemperatures could damage the catalytic converter, the fuelsystem, interior floor coverings
2nd row EasyFold™ seatback release (if equipped)WARNING: Ensure that the seat is unoccupied when folding itdown. Folding the seat while occupied could
Adjusting the second row seatbackWARNING: Reclining theseatback can cause anoccupant to slide under the seat’ssafety belt, resulting in severepersonal
To access the cup holders, lift upone of the slotted areas on thecover.WARNING: Use only soft cups in the cupholder. Hard objectscan injure you in a c
• The electrical wiring for the airbags, crash sensor(s), safety beltpretensioners, front safety belt usage sensors, driver seat positionsensor, front
Front passenger sensing systemFor airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occu
Front safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly ag
Safety belt precautionsWARNING: Always drive and ride with your seatback uprightand the lap belt snug and low across the hips.WARNING: To reduce the r
WARNING: Front and rear seat occupants, including pregnantwomen, should wear safety belts for optimum protection in anaccident.Combination lap and sho
WARNING: Failure to inspect and replace if necessary the beltand retractor assembly after an accident could increase the riskof injury in a collision.
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
Anti-lock brake system: If theABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected. Contact yourauthorized dealer as soon
The safety belt pretensioner tightens the safety belts firmly against theoccupant’s body at the start of the crash.WARNING: The driver and front passe
To adjust the comfort guide:1. Slip the shoulder belt into thebelt guide.2. Slide the guide up or down alongthe webbing so that the belt iscentered on
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war
If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the onposition or less than1-2 minutes h
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate
The driver and front passenger Belt-Minder威 features can bedeactivated/activated by performing the following procedure:Before following the procedure,
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important supplemental restraint system precautionsAirbags DO NOT inflate slowly orgently and the risk of in
WARNING: Never place your arm over the airbag module as adeploying airbag can result in serious arm fractures or otherinjuries.Steps you can take to p
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
Low tire pressure warning (ifequipped): Illuminates when yourtire pressure is low. If the lightremains on at start up or whiledriving, the tire pressu
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
• a readiness light and tone• and the electrical wiring which connects the components• Side curtain airbag system. Refer to Safety Canopy威 system late
The front passenger sensing system will turn off the passengerseatmounted side airbag if:• the seat is empty and safety belt is unbuckled.The front pa
If a person of adult size is sitting in the front passenger’s seat, but the⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator lamp is lit, it ispos
WARNING: Sitting improperly out of position or with the seatback reclined too far can take off weight from the seat cushionand affect the decision of
WARNING: To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a chi
WARNING: Any alteration/modification to the front passengerseat may affect the performance of the front passenger sensingsystem.Determining if the sys
WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. Contact your authorize
The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of
Safety Canopy姞 systemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a deploying
Low washer fluid (if equipped):Illuminates when the windshieldwasher fluid is low.Turn signal: Illuminates when theleft or right turn signal or thehaz
How does the Safety Canopy姞 system work?The design and development of theSafety Canopy威 system includedrecommended testing proceduresthat were develop
The Safety Canopy威 system is designed to activate when the vehiclesustains lateral deceleration sufficient to cause the side crash sensor toclose an e
Any difficulty with the system is indicated by one or more of thefollowing:• The readiness airbag light (same light as for front airbag system) willei
WARNING: All children are shaped differently. TheRecommendations for Safety Restraints are based on probablechild height, age and weight thresholds fr
Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeLargerchildrenChildren who have outgrown
Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe
WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli
restrained properly, then restrain the child in the child safety seat orwith the belt-positioning booster. Remember that child seats andbelt-positioni
When installing a child safety seat with combination lap/shoulder belts:• Use the correct safety belt buckle for that seating position.• Insert the be
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out.6. All
10. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the
The LATCH anchors are located atthe rear section of the rear seatbetween the cushion and seat back,below the locator symbols on theseat back. Follow t
WARNING: The standardized spacing for LATCH lower anchorsis 280 mm (11 inches) center to center. Do not use LATCHlower anchors for the center seating
The rear seats of your vehicle are equipped with built-in tether strapanchors located behind the seats as described below.The tether anchors in your v
3. Clip the tether strap to theanchor as shown.WARNING: If the tetherstrap is clipped incorrectly,the child safety seat may not beretained properly in
Booster seats position a child so that vehicle lap/shoulder safety belts fitbetter. They lift the child up so that the lap belt rests low across the h
Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the on position). The fuelgauge may vary slightly whe
NOTICE TO CROSSOVER VEHICLE OWNERSCrossover vehicles handle differentlythan passenger cars in the variousdriving conditions that areencountered on str
Note: Your AWD vehicle is not intended for off-road use. The AWDfeature gives your vehicle some limited off-road capabilities in whichdriving surfaces
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli
WARNING: The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydro
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
WARNING: Under-inflation is the most common cause of tirefailures and may result in severe tire cracking, tread separationor ⬙blowout⬙, with unexpecte
Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo
Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w
• With message centerSee TRIP A/B under Message centerin this chapter.MINI MESSAGE CENTER (IF EQUIPPED)Selectable featuresPress and release the TRIP/R
WARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the tires; spinning the tires can tear the tire andcause an explosion.
• Front Wheel Drive (FWD)/AllWheel Drive (AWD) vehicles(front tires at top of diagram)Sometimes irregular tire wear can be corrected by rotating the t
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw
Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti
Locks and Security 101Keys 101Locks 102Anti-theft system 115Seating and Safety Restraints 120Seating 120Safety restraints 132Airbags 147Child restrain
Reverse Sensing System (Park assist) (if equipped)This feature sounds a warning tone to warn the driver of obstacles nearthe rear bumper, and function
When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.
Low TirePressureWarning LightPossiblecauseCustomer Action RequiredFlashing WarningLightSpare tire inuseYour temporary spare tire is inuse. Repair the
under-inflated, carefully drive the vehicle to the nearest location whereair can be added to the tires. Inflate all the tires to the recommendedinflat
provide maximum return of vehicle design performance. Before loadingyour vehicle, familiarize yourself with the following terms for determiningyour ve
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
Steps for determining the correct load limit:1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.
calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 -540 = -103 kg. You will need to reduce the load weight by at least240 lb. (104
The distance to empty is calculated using a running average fueleconomy, which is based on your recent driving history of 500 miles(800 km). This valu
Do not exceed the maximum loads listed on the Safety ComplianceCertification label. For load specification terms found on the label, referto Vehicle l
Preparing to towUse the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. Contact your authorized dealer or
Trailer tow connector(equipped on vehicles with a Class II trailer tow/prep package)The trailer tow connector is located under the rear bumper, on the
• If you are driving down a long or steep hill, shift to a lower gear. Donot apply the brakes continuously, as they may overheat and becomeless effect
All Wheel Drive (AWD) vehicles:Tow your All Wheel Drive vehicle with all four wheels on the ground orwith all four wheels off the ground using a vehic
STARTINGPositions of the ignition1. Off— locks the automatictransmission gearshift lever andallows key removal. This positionalso shuts the engine and
WARNING: Do not start your vehicle in a closed garage or inother enclosed areas. Exhaust fumes can be toxic. Always openthe garage door before you sta
• Make sure the gearshift is in P(Park).3. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminate. See
2. Turn the key to 4 (start), then release the key as soon as the enginebegins cranking. Your vehicle has a computer assisted cranking systemthat assi
WARNING: To reduce the risk of electrical shock, do not useyour heater with ungrounded electrical systems or two-pronged(cheater) adapters.Prior to us
COMPASSThe compass heading is displayed in the message center display.The compass reading may be affected when you drive near largebuildings, bridges,
How to use the engine block heaterEnsure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth.Depending on the type
ABS warning lampThe ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringsta
Press the parking brake pedaldownward again to release theparking brake. Driving with theparking brake on will cause thebrakes to wear out quickly and
WARNING: If a failure has been detected within theAdvanceTrac威 with RSC威 system, the “sliding car” iconwillilluminate steadily. Verify that the Advanc
When AdvanceTrac威 with RSC威 performs a normal system self-check,some drivers may notice a slight movement of the brake, and/or arumble, grunting, or g
Electronic Stability Control (ESC)Electronic Stability Control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa
The Roll Stability Control system may be deactivated in certainsituations. See the Switching Off AdvanceTrac威 with RSC威 sectionfollowing.Switching Off
STEERINGTo help prevent damage to the power steering system:• Never hold the steering wheel at its furthest turning points (until itstops) for more th
If the fuse is not blown and the brakelamps are working properly, thefollowing procedure will allow you to move the gearshift lever from P(Park):1. Ap
WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your author
7. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) untilthe CIRCLE SLOWLY TO CALIBRATE display changes to CALIBRATIONCOMPLETED. It cou
R (Reverse)With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Re
• Allows the transmission to select gears that will provide the desiredengine braking based on the vehicle inputs mentioned above. This willincrease e
WARNING: To help avoid personal injury, please read andunderstand the limitations of the reverse sensing system ascontained in this section. Reverse s
The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to th
BLIND SPOT MIRRORS (IF EQUIPPED)Blind spot mirrors have anintegrated convex spotter mirrorbuilt into the upper outboard cornerof the outside mirrors.
ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED)Your vehicle may be equipped with a full-time All Wheel Drive (AWD)system. With the AWD option, power will b
If your vehicle goes off the edge of the pavement• If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ea
Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle (i.e.,
Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required f
Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should
Press RESET to turn autolock on or off.AUTOUNLOCKThis feature automatically unlocks all vehicle doors when the driver’sdoor is opened within 10 minute
Avoid sudden braking as well. Although an AWD vehicle may acceleratebetter than a two-wheel drive vehicle in snow and ice, it won’t stop anyfaster, be
DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
Canadian customers refer to your Customer Information Guidefor information on:• coverage period• exact fuel amounts• towing of your disabled vehicle•
FUEL PUMP SHUT-OFF SWITCHThis device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt.After an
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Not used (Spare)2 15A High-mount brake lamp (brakeon/off)3 15A
Fuse/RelayLocationFuse AmpRatingProtected Circuits11 10A All wheel drive (AWD)12 7.5A Power mirror switch, Driver sidepower seat memory, Driver seatmo
Fuse/RelayLocationFuse AmpRatingProtected Circuits38 20A Subwoofer/amplifier39 20A Radio40 20A Not used (spare)41 15A Automatic dimming rear viewmirro
The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 — Not used2 — Blower motor relay3 — Not
• Some messages will reappear after clearing or being reset if a problemor condition is still present and needs your attention.• Some messages can be
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription16 30A** Front heated seats17 20A** Cigar lighter/Power point18 20A** Panoramic moon
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription46 10A* Trailer tow right stop/turn lamp47 — Trailer tow right stop/turn lamp relay48
CHANGING THE TIRESIf you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel
When driving with one of the dissimilar spare tires listed above, do not:• Exceed 50 mph (80 km/h)• Load the vehicle beyond maximum vehicle load ratin
When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to:• Towing a trailer• Driving vehicles equipped with a
Tire change procedureWARNING: When one of the front wheels is off the ground, thetransmission alone will not prevent the vehicle from moving orslippin
WARNING: To lessen the risk of personal injury, do not put anypart of your body under the vehicle while changing a tire. Do notstart the engine when y
Stowing the flat/spare tire and jack1. Fully collapse the jack, fold the wrench socket into the handle andplace them both into the bag making sure to
WARNING: When a wheel is installed, always remove anycorrosion, dirt or foreign materials present on the mountingsurfaces of the wheel or the surface
Preparing your vehicleWhen the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a
TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressuresensor is malfunctioning, or your spare tire is in use. For moreinformation on how the syst
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
If the vehicle is towed by other means or incorrectly, vehicledamage may occur.Ford Motor Company produces a towing manual for all authorized towtruck
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized
In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph
In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con
AUDIO SYSTEMSQuick start — How to get goingWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
If your vehicle must be serviced while you are traveling or living inCentral America, the Caribbean, or the Middle East, contact the nearestauthorized
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is
WAXING• Wash the vehicle first.• Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your aut
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub
INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENSClean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth,
INTERIORFor fabric, carpets, cloth seats and safety belts:• Remove dust and loose dirt with a vacuum cleaner.• Remove light stains and soil with Motor
FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and
Listening to satellite radio (if equipped)1. If the audio system is turned off,press VOL-PUSH to turn the radioon. Turn VOL-PUSH to adjust thevolume.N
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column.2. Go to th
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT1. Engine coolant reservoir2. Power steering fluid reservoir3. Brake fluid reservoir4. Battery5. Power
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Press the locktab to release the bl
4. Attach the new wiper to thewiper arm and press it into placeuntil a click is heard.If you find this procedure toodifficult, please see your dealer.
• If the oil level is within thisrange, the oil level is acceptable.DO NOT ADD OIL.• If the oil level is below thismark, engine oil must be addedto ra
3. Recheck the engine oil level. Make sure the oil level is not above thenormal operating range on the engine oil level dipstick.4. Install the dipsti
Ford production and Motorcraft replacement oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedthat
WARNING: When lifting a plastic-cased battery, excessivepressure on the end walls could cause acid to flow through thevent caps, resulting in personal
For a single CD system, if a discis not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the
If the battery has been disconnected or a new battery has been installed,the clock and radio settings must be reset once the battery isreconnected.• A
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the FULL COLD level or within theCOLD
Note: Do not use stop leak pellets or cooling system sealants/additivesas they can cause damage to the engine cooling and/or heating systems.This dama
If you removed the radiator cap in an overflow system, fill the radiatoruntil the coolant is visible and radiator is almost full.6. Replace the cap. T
• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequatefreeze protection at the tempera
Continued operation will increase the engine temperature:• The engine will completely shut down.• Steering and braking effort will increase.Once the e
WARNING: The fuel system may be under pressure. If the fuelfiller cap is venting vapor or if you hear a hissing sound, waituntil it stops before compl
clothing and wash skin thoroughly with soap and water. Repeated orprolonged skin contact with fuel liquid or vapor causes skin irritation.• Be particu
• DO NOT use a device that would hold the fuel pump handle in the fillposition.Fuel filler capWhen fueling your vehicle:1. Turn the engine off.2. Care
WARNING: If you do not use the proper fuel filler cap,excessive vacuum in the fuel tank may damage the fuel systemor cause the fuel cap to disengage i
Customer Assistance 266Reporting safety defects (U.S. only) 272Reporting safety defects (Canada only) 272Cleaning 273Maintenance and Specifications 28
Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random pl
Fuel qualityIf you are experiencing starting, rough idle or hesitation driveabilityproblems, try a different brand of unleaded gasoline. If the proble
ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform
Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers).2. Each time you fill the tan
• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between the top gears occurs. Unnecessaryshifting of this type co
EPA fuel economy estimatesEvery new vehicle should have a sticker on the window called theMonroney Label which contains EPA fuel economy estimates. Co
WARNING: Exhaust leaks may result in entry of harmful andpotentially lethal fumes into the passenger compartment.Do not make any unauthorized changes
detected by the OBD-II may not have symptoms that are apparent,continued driving with the service engine soon indicator on canresult in increased emis
POWER STEERING FLUIDCheck the power steering fluid. Refer to scheduled maintenanceinformation.1. Start the engine and let it rununtil it reaches norma
TRANSMISSION FLUIDChecking automatic transmission fluidRefer to your scheduled maintenance information for scheduledintervals for fluid checks and cha
The transmission fluid should bewithin the cross-hatch area if atnormal operating temperature180°F-200°F (82°C-93°C) .High fluid levelFluid levels abo
AM/FM Single CD/MP3 satellite compatible sound system(if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and
WARNING: To reduce the risk of vehicle damage and/orpersonal burn injuries do not start your engine with the aircleaner removed and do not remove it w
MOTORCRAFT PART NUMBERSComponent 3.5L V6 EngineEngine air filter element FA-1884Battery BXT-36ROil filter FL-500-SSpark plugs11For spark plug replacem
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationBrake fluidBetween MIN andMAX on rese
Item Capacity Ford part nameFord part number /Ford specificationEngine oil15.5 quarts (5.2L)•Motorcraft SAE 5W-20Premium Synthetic BlendMotor Oil (US)
Item Capacity Ford part nameFord part number /Ford specificationPower Transfer Unit(PTU) fluid (AWD)512 ounces (0.35L)Motorcraft SAE 75W-140Synthetic
ENGINE DATAEngine 3.5L-DOHC V6 engineCubic inches 214Required fuel 87 octaneFiring order 1–4–2–5–3–6Spark plug gap 0.050–0.057 inch (1.29–1.45 mm)Igni
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
LifestyleAsh cup / coin holderCargo organization and managementCross barsTrailer hitches, wiring harnesses and accessoriesPeace of mindRemote startKey
In satellite radio mode (if equipped), press / to tune to thenext/previous channel.In CATEGORY MODE, press/ to scroll through the list ofavailable SIR
FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on
Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With
Ford Extended Service Plan3222010 Edge (edg)Owners Guide (own2002), 1st PrintingUSA (fus)
AAccessory delay ...78AdvanceTrac ...222Air cleaner filter ...309–311Air conditioning ..
Child safety seats - boosterseats ...176Cleaning your vehicleengine compartment ...275instrument pa
change oil soon warning,message center ...285checking and adding ...285dipstick ...285
Instrument panelcleaning ...277cluster ...12lighting up panel andinterior ...
Passenger OccupantClassification Sensor ...134Power distribution box(see Fuses) ...248Power door locks ...
Specification chart,lubricants ...312Speed control ...80Starting your vehicle ...215–2
• DELETE SONG: Press OK to delete a song from the system’smemory. Press/ to cycle through the saved songs. When thesong appears in the display that yo
To activate, press MENU repeatedly until RBDS (ON/OFF) appears inthe display. Use / / SEEK to toggle RBDS ON/OFF. WhenRBDS is OFF, you will not be abl
TRACK/FOLDER MODE: Available only on MP3 discs in CD mode.In track mode, pressSEEK, SEEK to scroll through all tracks onthe discIn folder mode, pressS
In satellite radio mode (if equipped), press SEEK, SEEK toseek to the previous/next channel. If a specific category is selected,(Jazz, Rock, News, etc
9. FOLDER: In folder mode,pressFOLDER to access theprevious folder on MP3 discs, ifavailable.10. FF (Fast forward): Press FFto manually advance in a C
selected category. Press again to stop.Satellite radio is available only with a valid SIRIUS radiosubscription. Check with your authorized dealer for
Premium sound AM/FM in-dash six CD/MP3 satellite compatiblesound system (if equipped)WARNING: Driving while distracted can result in loss of vehicleco
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
In satellite radio mode (if equipped), press / to tune to thenext/previous channel.In CATEGORY MODE, press/ to scroll through the list ofavailable SIR
• DELETE SONG: Press OK to delete a song from the system’smemory. Press/ to cycle through the saved songs. When thesong appears in the display that yo
RBDS: Available only in FM mode. This feature allows you to searchRBDS-equipped stations for a certain category of music format:CLASSIC, COUNTRY, INFO
Track/Folder mode: Available only on MP3 discs in CD mode.In track mode, pressSEEK, SEEK to scroll through all tracks onthe disc.In folder mode, press
In satellite radio mode (if equipped), press SEEK, SEEK toseek to the previous/next channel. If a specific category is selected,(Jazz, Rock, News, etc
10. FF (Fast forward): Press FFto manually advance in a CD/MP311. REW (Rewind): Press REW tomanually reverse in a CD/MP3 track.12. Memory presets: To
14. AM/FM: Press to selectAM/FM1/FM2 frequency band.15. ON/OFF/Volume: Press to turnon/off. Turn to increase/decreasevolume.Note: If the volume is set
To auto eject up to 6 CDs, press and hold until the system beginsejecting all loaded discs. If the discs are not removed, the system willreload the di
3. Attach one end of the audio extension cable to the headphone outputof your player and the other end of the audio extension cable to the AIJin your
USB port (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdriver
Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti
CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C
CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m
Radio Display Condition Action RequiredNO TEXT Category informationnot available.Category informationnot available at thistime on this channel.The sys
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
5. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. Engagesautomatically in
DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEMWITH HEATED SEATS (IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer
6. Recirculated air: Press to activate/deactive air recirculation inthe vehicle. Recirculated air may reduce the amount of time needed tocool down the
Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance
13. AUTO: To engage automatic temperature control, press AUTO andselect the desired temperature using the temperature control. Thesystem will automati
To aid in side window defogging/demisting in cold weather:1. Select.2. Select A/C.3. Adjust the temperature control to maintain comfort.4. Set the fan
HEADLAMP CONTROLRotate the headlamp control to thefirst positionto turn on theparking lamps.Rotate to the second positiontoturn on the headlamps.Rotat
Fog lamp control (if equipped)The headlamp control also operatesthe fog lamps. The fog lamps can beturned on when the headlampcontrol is in the, ,orpo
WARNING: Always remember to turn on your headlamps atdusk or during inclement weather. The Daytime Running Lamp(DRL) system does not activate the tail
• (1) 8 feet (2.4 meters)• (2) Center height of lamp toground• (3) 25 feet (7.6 meters)• (4) Horizontal reference line2. Measure the height of thehead
TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSFront row map lamps (if equipp
Map/dome lamp (if equipped)The dome lamp lights when:• any door is opened,• the instrument panel dimmerswitch is rotated up until thecourtesy lamps co
• Large water droplets, drip marks or streaks present on the interior ofthe lensTake your vehicle to dealer for service if any of the above conditions
Replacing interior bulbsCheck the operation of all bulbs frequently.Replacing headlamp bulbsCheck the operation of all bulbs frequently.1. Make sure t
DATA RECORDINGService Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehi
Replacing front parking lamp/turn signal bulbs1. Make sure that the headlamp control is in the off position.2. Open the hood.3. Reach over the front b
6. Install the bulb socket into the lamp assembly and rotate clockwise.7. Carefully install the tail lamp assembly on the vehicle by securing thelamp
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
Rear window wiper/washer controlsFor rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select:2 — Normal spe
ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamp.Slide on rod featureThe visor will slide back and forthon
CENTER CONSOLE (IF EQUIPPED)Your vehicle may be equipped with a variety of console features. Theseinclude:1. Cupholders2. Tissue box holder (located o
To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe ba
To operate one-touch down:• Press the switch completely downto the second detent and releasequickly. The window will openfully. Momentarily press thes
Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controls(except for the driver’s) pres
EXTERIOR MIRRORSPower side view mirrorsWARNING: Do not adjust the mirror while the vehicle is inmotion.To adjust your mirrors:1. Rotate the control cl
To access this information, special equipment must be directlyconnected to the recording modules. Ford Motor Company andFord of Canada do not access e
SPEED CONTROLWith speed control set, you can maintain a set speed without keepingyour foot on the accelerator pedal.WARNING: Do not use the speed cont
Disengaging speed controlPress the brake pedal to disengage the speed control. Disengaging thespeed control will not erase the previous set speed.Resu
STEERING WHEEL CONTROLS (IF EQUIPPED)These controls allow you to operate some radio control features.Radio control featuresVOL + (Volume): Press to in
Navigation system/SYNC威 handsfree control features (ifequipped)Presscontrol briefly until thevoiceicon appears on theNavigation display to use the voi
To open power sunshades andpanoramic Vista Roof™: Pressand release the control toopen the sunshade. The front andrear sunshades open simultaneously.No
HomeLink威Car2U威 Home AutomationSystemHomeLink姞 Wireless Control System (if equipped)The HomeLink威 Wireless ControlSystem, located on the driver’s viso
Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink威 equipped vehiclepurchase). I
5. Firmly press and release the “learn” or “smart” button. (The name andcolor of the button may vary by manufacturer.)Note: There are 30 seconds in wh
Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet
Car2U姞 Home Automation System (if equipped)The Car2U威 Home AutomationSystem is a universal transmitterlocated in the driver’s visor thatincludes two p
WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers use extreme caution
• Fixed code garage door openers were produced prior to 1996. Fixedcode uses the same coded signal every time. It is manuallyprogrammed by setting DIP
2. Go to the garage to locate thegarage door opener motor and its“learn” button. You may need aladder to reach the unit and youmay need to remove the
Note: The Car2U威 system allows for three devices to be programmed. Ifyou need to change or replace any of the three devices after it has beeninitially
3. To input these positions into theCar2U威 system, simultaneouslypress all three Car2U威 systembuttons for a few seconds and thenrelease to put the dev
To erase programming on the Car2U威 system (individual buttons cannotbe erased), use the following procedure:1. Firmly press the two outsideCar2U威 syst
• Do not leave the liftgate open while driving. Doing so could causeserious damage to the liftgate and its components as well as allowingcarbon monoxi
• or the vehicle speed is at or above 3 mph (5 km/h)If the liftgate reverses and starts to close after an open request, a fastcontinuous chime indicat
To power open or close theliftgate with the integratedkeyhead transmitter:Presstwice within threeseconds to open the liftgate. Referto Remote entry sy
Note: The liftgate movement direction can be reversed with a secondpress of the instrument panel, or the rear cargo area control button, or asecond do
CARGO AREA FEATURESCargo management system (if equipped)The cargo management systemconsists of storage compartmentslocated in the floor of the rear ca
Commentaires sur ces manuels