Introduction 4Instrument Cluster 14Warning lights and chimes 14Gauges 19Message center 21Entertainment Systems 29AM/FM stereo 29AM/FM stereo with CD 3
Vehicle Modification Data RecordingSome aftermarket products may cause severe engine and/or transmissiondamage; refer to the What is not covered secti
Reasons given... Consider...“I was in a hurry” Prime time for an accident.Belt-Minder威 reminds us to take a fewseconds to buckle up.“Safety belts don’
Deactivating/activating the Belt-Minder姞 featureRead Steps1-5thoroughly before proceeding with thedeactivation/activation programming procedure.The Be
• This will enable the Belt-Minder威 feature for that seating position if itis currently disabled. As confirmation, the safety belt warning light willf
Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in
WARNING: Do not put anything on or over the air bag module.Placing objects on or over the air bag inflation area may causethose objects to be propelle
How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustains alongitudinal deceleration suff
• safety belt pretensioners• a readiness light and tone• a diagnostic module• and the electrical wiring which connects the componentsThe diagnostic mo
SOS Post-Crash Alert System™The system automatically flashes the turn signal lamps and sounds thehorn three times at four second intervals in the even
Turning the passenger airbag off1. Insert the ignition key, turn theswitch to OFF position and hold inOFF position while removing thekey.2. When the i
WARNING: If the OFF light is illuminated when the passengerairbag switch is in the ON position and the ignition switch is inON, have the passenger air
WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers use extreme caution
safety belts, because safety belts in modern vehicles are designed towork as a safety system with the airbags.Read all airbag warning labels in the ve
WARNING: This vehicle has special energy management safetybelts for the driver and right front passenger. These particularbelts are specifically desig
3. Medical condition: A passenger has a medical condition that,according to his or her physician:• poses a special risk for the passenger if the airba
Important child restraint precautionsWARNING: Always make sure your child is secured properly ina device that is appropriate for their height, age and
Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfantsor tod-dlersChildren weighing 40 l
Recommendations for attaching child safety restraints for childrenRe-straintTypeChildWeightUse any attachment method as indicated be-low by “X”LATCH(l
WARNING: Always carefully follow the instructions andwarnings provided by the manufacturer of any child restraint todetermine if the restraint device
training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertifi
Airbags can kill or injure a child in a child seat. NEVER place arear-facing child seat in front of an active airbag. If you must use aforward-facing
1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
towards the buckle will additionally help to remove remaining slack fromthe belt.9. Attach the tether strap (if thechild seat is equipped). Refer toAt
Your vehicle has LATCH lower anchors for child seat installation at thefollowing locations:• Five passenger crew van• Seven passenger wagon• Eight pas
• Twelve passenger wagon• Fifteen passenger wagonThe LATCH lower anchors arelocated at the rear section of therear seat between the cushion andseatbac
without lifting the front of the child seat. Keeping the child seat justtouching the vehicle seat gives the best protection in a severe crash.Each tim
Once the child safety seat has been installed using either the safety belt,the lower anchors of the LATCH system, or both, you can attach the toptethe
2. Route the child safety seat tetherstrap over the back of the frontright-hand passenger seat as shown.3. Clip the tether strap hook to theseat pedes
4. Adjust the front right handpassenger seat to the full rearwardposition.5. Tighten the child safety seattether strap according to themanufacturer’s
2. Clip the tether strap hook to theseat pedestal at the location shown.If the tether strap is clippedincorrectly, the child safety seat maynot be ret
2. Route the child safety tetherstrap over the back of the benchseat.3. Clip the center tether strap hookto the tether bracket mountedunder rear rail
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
Booster seats position a child so that vehicle lap/shoulder safety belts fitbetter. They lift the child up so that the lap belt rests low across the h
Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
VEHICLE CHARACTERISTICSHow your vehicle differs from other vehiclesSUV and trucks can differ fromsome other vehicles in a fewnoticeable ways. Your veh
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli
WARNING: The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydro
• Recommended inflation pressure: The cold inflation pressure foundon the Safety Compliance Certification Label or Tire Label located onthe B-Pillar o
on the tire. The Ford recommended tire inflation pressure is found onthe Safety Compliance Certification Label or Tire Label which is locatedon the B-
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa
Note: Some spare tires operate at a higher inflation pressure than theother tires. For T-type/mini-spare tires (see Dissimilar SpareTire/Wheel Informa
Tire inflation informationAll tires with Steel Carcass Plies (if equipped):This type of tire utilizes steel cords in the sidewalls. As such, theycanno
WARNING: Stay out of the trajectory (1) as indicated in theillustration.TIRE CAREInspecting your tires and wheel valve stemsPeriodically inspect the t
Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w
• Do not run over curbs or hit the tire against a curb when parkingWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the
• Rear-wheel drive (RWD)vehicles/Four-wheel drive(4WD)/All-wheel drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can b
• DRW – Six tire rotationIf your vehicle is equipped with dualrear wheels it is recommended thatthe front and rear tires (in pairs) berotated only sid
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
light will stay on until the engine is cranked, then turn itself off if nomalfunctions are present. However, if after 15 seconds the service enginesoo
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe
The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw
In either case, the pressure sensor is covered by the tire and isnot visible unless the tire is removed. Care must be taken whenchanging the tire to a
• Metal valve stem with bandedsensor- the valve stem iscompletely metal.Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Mon
When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.
Low TirePressureWarningLightPossible cause Customer Action RequiredFlashingWarningLightSpare tire in use Your temporary spare tire is in use.Repair th
WARNING: Driving a vehicle with the brake system warninglight on is dangerous. A significant decrease in brakingperformance may occur. It will take yo
TPMS reset procedureThe TPMS reset procedure needs to be performed after each tirerotation on vehicles that require different recommended tirepressure
Performing the TPMS reset procedure(Vehicles that have wheels with snap-in pressure sensors)It is recommended that you read the entire procedure befor
6. Remove the valve cap from the valve stem on the left front tire.Decrease the air pressure until the horn sounds.Note: The single horn chirp confirm
Please take the tool with theprovided Velcro威 strip on the backand mount it in the bottom rightcorner of your Owner’s Guide case(as shown) for safe ke
3. Cycle the ignition from off to onthree (3) times ending in the onposition—DO NOT start the engine.4. Press and hold the brake pedalfor two (2) seco
7. Train the TPMS sensors in the tires using the following TPMS resetsequence starting with the left front tire in the following clockwiseorder:1. Lef
10. Perform Steps 8 and 9 on the right front tire, right rear tire andfinally the left rear tire. Training is complete after the horn sounds forthe la
VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
WARNING: Never remove the coolant reservoir cap while theengine is running or hot.Low tire pressure warning (ifequipped): Illuminates when yourtire pr
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the
to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400
Distribute the load so that only 10–15% of the total is on the tongue. Tiedown the load so that it does not shift and change the weight on thehitch.To
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb(kg)MaximumLoaded TrailerWeight - lb (kg)Maximumfrontal area oft
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb(kg)MaximumLoaded TrailerWeight - lb (kg)Maximumfrontal area oft
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb(kg)MaximumLoaded TrailerWeight - lb (kg)Maximumfrontal area oft
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb(kg)MaximumLoaded TrailerWeight - lb (kg)Maximumfrontal area oft
Anti-theft system: Flashes whenthe SecuriLock威 Passive Anti-theftSystem has been activated.Overdrive off (if equipped):Illuminates when the overdrivef
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb(kg)MaximumLoaded TrailerWeight - lb (kg)Maximumfrontal area oft
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb(kg)MaximumLoaded TrailerWeight - lb (kg)Maximumfrontal area oft
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb(kg)MaximumLoaded TrailerWeight - lb (kg)Maximumfrontal area oft
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb(kg)MaximumLoaded TrailerWeight - lb (kg)Maximumfrontal area oft
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb(kg)MaximumLoaded TrailerWeight - lb (kg)Maximumfrontal area oft
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb(kg)MaximumLoaded TrailerWeight - lb (kg)Maximumfrontal area oft
WARNING: Do not connect a trailer’s hydraulic brake systemdirectly to your vehicle’s brake system. Your vehicle may nothave enough braking power and y
during manual activation without a trailer connected or when gainadjustments are made with no trailer connected.• TBC GAIN = XX.X OUTPUT = //////: Whe
1. Make sure the trailer brakes are in good working condition,functioning normally, and properly adjusted. See your trailer dealer ifnecessary.2. Hook
Points to Remember:• Remember to adjust gain setting before using the TBC for the firsttime.• Readjust GAIN setting on the TBC (according to procedure
Parking brake on warning chime: Sounds when the parking brake isset, the engine is running and the vehicle is driven more than 3 mph(5 km/h).GAUGESSpe
Driving while you towWhen towing a trailer:• To ensure proper break-in of powertrain components, do not trailertow during the first 1,000 miles (1,600
refilling your rear axle with synthetic gear lube if not already soequipped. Refer to the Maintenance and Specifications chapter forthe lubricant spec
STARTINGPositions of the ignition1. Accessory — allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. Lock —
WARNING: Do not start your vehicle in a closed garage or inother enclosed areas. Exhaust fumes can be toxic. Always openthe garage door before you sta
• Turn the key to 4 (on) withoutturning the key to 5 (start).Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrume
You may experience a decrease in peak performance when the engine iscold when operating on E85ethanol.Do not crank the engine for more than 10 seconds
See Cold weather starting earlier in this chapter for more informationon starting with ethanol.WARNING: Failure to follow engine block heater instruct
become very hot and may result in an electrical shock or fire. Be sureto check for heat anywhere in the electrical hookup once the systemhas been oper
Using ABSWhen hard braking is required, apply continuous force on the brakepedal; do not pump the brake pedal since this will reduce theeffectiveness
your vehicle in an emergency. Since the parking brake applies only therear brakes, the vehicle’s stopping distance will increase greatly and thehandli
Seating and Safety Restraints 85Seating 85Safety restraints 93Airbags 102Child restraints 112Tires, Wheels and Loading 134Tire information 136Tire inf
WARNING: Never remove the coolant reservoir cap while theengine is running or hot.Odometer: Registers the total miles(kilometers) of the vehicle.Refer
ADVANCETRAC姞 WITH ROLL STABILITY CONTROL™ (RSC姞)STABILITY ENHANCEMENT SYSTEM (IF EQUIPPED)WARNING: Vehicle modifications involving braking system,afte
The AdvanceTrac威 with RSC威 system provides the following stabilityenhancement features for certain driving situations:• Traction control system (TCS),
• If the driving condition is severe and your foot is not on the brake, thebrake pedal may move as the systems applies higher brake forces. Youmay als
Certain adverse driving maneuvers may activate the ESC system, whichinclude but are not limited to:• Taking a turn too fast• Maneuvering quickly to av
AdvanceTrac威 with RSC威 “Off” button again or if the vehicle is above20 mph (32 km/h) will turn off the “sliding car”icon. The switch willnot allow par
• Do not fill the power steering pump reservoir above the FULL COLDrange on the dipstick, as this may result in leaks from the reservoir.If the power
WARNING: Loaded vehicles, with a higher center of gravity,may handle differently than unloaded vehicles. Do not overloadyour vehicle and use extra pre
Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,
If the fuse is not blown and the brake lamps are working properly, thefollowing procedure will allow you to move the gearshift lever from P(Park):1. A
AUTOMATIC TRANSMISSION OPERATIONUnderstanding the gearshift positions of the 4–speed automatictransmissionYour vehicle has been designed to improve fu
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the on position). The fuelgauge may vary slightly whe
WARNING: Always set the parking brake fully and make surethe gearshift is latched in P (Park). Turn the ignition to the lockposition and remove the ke
2 (Second)This position allows for second gear only.• Provides engine braking.• Use to start-up on slippery roads.• To return to(Overdrive), move the
The adaptive transmission shift strategy allows the transmission torelearn these operating parameters. This learning process could takeseveral transmi
To activate tow/haul, press thebutton on the end of the gearshiftlever.The TOW HAUL indicator light willilluminate in the instrument cluster.Tow/haul
• The transmission will not downshift into 1 (First) at high speeds; itwill downshift to a lower gear and then shift into 1 (First) when thevehicle re
WARNING: Always set the parking brake fully and make surethe gearshift is latched in P (Park). Turn the ignition to theLOCK position and remove the ke
Used for improved traction on slippery roads. Selecting 3 (Third)provides additional engine braking.2 (Second)Use 2 (Second) to start-up on slippery r
REVERSE SENSING SYSTEM (IF EQUIPPED)The reverse sensing system (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when the R (Rev
The RSS detects obstacles up to6 feet (2 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the fi
REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rearview camera system locatedon the back door provides a videoimage, which appears in therearview mirror or n
XX.X MPG (L/100km)Average fuel economy displays your average fuel economy in miles/gallonor liters/100 km.If you calculate your average fuel economy b
Note: The default setting for the rear camera delay is off. Press the“Settings” button found on the navigation screen (if equipped) to set therear cam
Servicing• If the image comes on while the vehicle is not in R (Reverse), havethe system inspected by your authorized dealer.• If the image is not cle
WARNING: Objects in the blind spot mirror are closer than theyappear.VEHICLE USED AS A STATIONARY POWER SOURCEAuxiliary equipment called power take-of
DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co
Press in the flasher control and all front and rear direction signals willflash. Press the flasher control again to turn them off. Use it when yourveh
On commercial stripped chassisvehicles, this switch is located on abracket above the brake pedal.To reset the switch:1. Turn the ignition off.2. Check
FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth
WARNING: Always disconnect the battery before servicing highcurrent fuses.If your vehicle is equipped with an auxiliary battery,disconnecting the prim
To reset the oil monitoring system to 100% after each oil change(approximately 7,500 miles [12,000 km] or 12 months) perform thefollowing:1. Press and
Fuse/RelayLocationFuse AmpRatingProtected Circuits5 10A Passenger compartment fusepanel (SPDJB)/Brake-shiftinterlock6 20A Turn signal, Hazard, Stop la
Fuse/RelayLocationFuse AmpRatingProtected Circuits33 10A Trailer brake controller34 5A Not used (spare)35 10A Reverse park aid, Rear videocamera, Cuta
WARNING: To reduce risk of electrical shock, always replacethe cover to the Power Distribution Box before reconnecting thebattery or refilling fluid r
Fuse/RelayLocationFuse AmpRatingProtected Circuits10 HC ISO Fuel injector control module(FICM) relay (Diesel engine only)11 — Not used12 40A** Modifie
Fuse/RelayLocationFuse AmpRatingProtected Circuits33 40A** Anti-lock brake system (ABS)pump34 20A** Stripped chassis horn35 40A** PCM relay36 20A** Ig
Fuse/RelayLocationFuse AmpRatingProtected Circuits57 20A* Trailer tow park lamp58 15A* Trailer tow backup lamp59 — Not used60 — One touch integrated s
Fuse/RelayLocationFuse AmpRatingProtected Circuits82 — Not used83 — Fuel pump (diode)84 — Not used85 HC Micro relay Upfitter #1* Mini fuses ** A1S fus
replace it as soon as possible with a road tire/wheel that is the same sizeand type as the road tires and wheels that were originally provided byFord.
• Use snow chains on the end of the vehicle with the dissimilar sparetire/wheelThe usage of a full-size dissimilar spare tire/wheel can lead toimpairm
4. Apply the parking brake and turnthe engine off.Spare tire informationThe spare tire for your vehicle is stowed under the rear of your vehicle(excep
PARK AID (if equipped)This feature sounds a warning tone to warn the driver of obstacles nearthe rear bumper, and functions only when R (Reverse) gear
Tire change procedureWARNING: To help prevent the vehicle from moving when youchange a tire, be sure the parking brake is set, then block (inboth dire
• The jack is located in the rearright-hand side of the cargo area.3. Remove any wheel trim. Insert the tapered end of the lug nut wrenchbehind wheel
2. Position the jack to raise the front or rear wheel.• Never use the front or reardifferential as a jacking point.Rear axle jacking points - Allmodel
Front axle jacking points:Place the jack under the pin on thefront surface of the front axle.Do not place the jack under oron the steering linkage.3.
8. Remove the jack and fully tighten the lug nuts in the following pattern(Refer to Wheel lug nut torque specifications later in this chapter forthe p
4. Check that the tire lies flat against the frame and is properlytightened. Try to push or pull, then turn the tire to be sure it will notmove. Loose
WARNING: When a wheel is installed, always remove anycorrosion, dirt or foreign materials present on the mountingsurfaces of the wheel or the surface
Preparing your vehicleWhen the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto
check. Instead, quickly release the stem and repeatedly press it again toscroll through the setup menu until the message center displaysCOMPASS ZONE X
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
Emergency towingIn case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport veh
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized
In Canada:Mailing Address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph
• current odometer reading• vehicle identification number (VIN)Additional AssistanceIf you have questions or concerns, or are unsatisfied with the ser
California Civil Code Section 1793.22(b) presumes that the manufacturerhas had a reasonable number of attempts to conform the vehicle to itsapplicable
for your name and address, general information about your new vehicle,information about your warranty concerns, and any steps you havealready taken to
GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.
LANGUAGE = ENGLISH / SPANISH / FRENCHAllows you to choose which language the message center will display in.Selectable languages are English, Spanish,
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i
WAXING• Wash the vehicle first.• Do not use waxes that contain abrasives; use Motorcraft威 PremiumLiquid Wax (ZC-53-A), which is available from your au
• To remove tar and grease, use Motorcraft威 Bug and Tar Remover(ZC-42), available from your authorized dealer.ENGINEEngines are more efficient when th
• For routine cleaning, use Motorcraft威 Detail Wash (ZC-3-A).• If tar or grease spots are present, use Motorcraft威 Bug and TarRemover (ZC-42).WINDOWS
• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to a
WARNING: Do not use cleaning solvents, bleach or dye on thevehicle’s seatbelts, as these actions may weaken the beltwebbing.LEATHER SEATS (IF EQUIPPED
Motorcraft威 Dusting Cloth (ZC-24)Motorcraft威 Engine Shampoo and Degreaser (U.S. only) (ZC-20)Motorcraft威 Engine Shampoo (Canada only) (CXC-66-A)Motorc
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
Types of messages and warnings:• Some messages will appear briefly to inform you of something youmay need to take action on or be informed of.• Some m
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENTRefer to the 6.0 and 6.4 Liter Power Stroke Direct Injection TurboDiesel Owner’s Guide Supplement for
State or local regulations on volatile organic compounds may restrict theuse of methanol, a common windshield washer antifreeze additive.Washer fluids
3. Set the parking brake and ensure the gearshift is securely latched in P(Park).4. Open the hood. Protect yourself from engine heat.5. Locate and car
2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler cap
Change your engine oil and filter according to the appropriate schedulelisted in the scheduled maintenance information.Ford production and Motorcraft威
Note: Electrical or electronic accessories or components added tothe vehicle by the dealer or the owner may adversely affectbattery performance and du
Battery relearnBecause your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the batte
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the FULL COLD level or within theCOLD
BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is lowand the brake system should be inspected immediately. Refer to Brakefluid in the Mainten
WARNING: Do not add engine coolant when the engine is hot.Steam and scalding liquids released from a hot cooling systemcan burn you badly. Also, you c
WARNING: To reduce the risk of personal injury, make sure theengine is cool before unscrewing the coolant pressure relief cap.The cooling system is un
Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant since a Ford-approved recycling process is not yet avai
What you should know about fail-safe cooling (if equipped)If the engine coolant supply is depleted, this feature allows the vehicle tobe driven tempor
2. Arrange for the vehicle to be taken to an authorized dealer.3. If this is not possible, wait a short period for the engine to cool.4. Check the coo
WARNING: If you do not use the proper fuel filler cap,excessive vacuum in the fuel tank may damage the fuel systemor cause the fuel cap to disengage i
sensitive individuals, serious personal injury or sickness may result. Iffuel is splashed on the skin, promptly wash skin thoroughly with soapand wate
WARNING: The flow of fuel through a fuel pump nozzle canproduce static electricity, which can cause a fire if fuel ispumped into an ungrounded fuel co
5. Turn the filler cap clockwise 1/4 of a turn until it clicks at least once.If the check fuel cap lightor a “check fuel cap” message comes on,the fue
FFV (Flex Fuel Vehicle) fuel capIf your vehicle is FFV capable, it will have a yellow colored fuel cap.Choosing the right fuelIf your vehicle is a fle
AUDIO SYSTEMSAM/FM stereo system (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strong
Do not be concerned if your enginesometimes knocks lightly. However,if it knocks heavily under mostdriving conditions while you areusing fuel with the
rating. These products have not been approved for your engine andcould cause damage to the fuel system. Repairs to correct the effects ofusing an afte
The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fu
Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fuelecon
• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled mainten
• Do not turn off the ignition while your vehicle is moving, especially athigh speeds.• Have the items listed in scheduled maintenance informationperf
On-board diagnostics (OBD-II)Your vehicle is equipped with a computer that monitors the engine’semission control system. This system is commonly known
Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect
POWER STEERING FLUIDCheck the power steering fluid.Refer to the scheduled maintenanceguide for more information.Check the fluid level when it is at am
6. If the fluid is low, add fluid in small amounts, continuously checkingthe level until it reaches the FULL COLD range. Be sure to put thedipstick ba
Customer Assistance 254Reporting safety defects (U.S. only) 260Reporting safety defects (Canada only) 261Cleaning 262Underbody preservation 267Mainten
2. AUDIO: Press AUDIO repeatedlyto gain access to the followingsettings:BAL (Balance): Press AUDIO to reach the balance setting.Use/ / SEEK to adjust
TRANSMISSION FLUIDChecking automatic transmission fluid (if equipped)Refer to your scheduled maintenance information for scheduledintervals for fluid
Low fluid levelDo not drive the vehicle if the fluid level is at the bottom of the dipstickand the ambient temperature is above 50°F (10°C).Correct fl
The transmission fluid should be in this range if at normal operatingtemperature (150°F-170°F [66°C-77°C]).The transmission fluid should be in this ra
High fluid levelFluid levels above the safe range may result in transmission failure.An overfill condition of transmission fluid may cause shift and/o
If an overfill occurs, excess fluid should be removed by an authorizeddealer.An overfill condition of transmission fluid may cause shift and/orengagem
Automatic transmission fluid filterThe Torqshift automatictransmission is equipped with aserviceable transmission fluid filterlocated inside the trans
Changing the air filter element1. Disconnect the fresh air inlet tubefrom the radiator support.2. Open the clamp that secures thetwo halves of the air
MOTORCRAFT PART NUMBERSComponent* 4.6L V8 engine 5.4L V8 engine6.8L V10engineAir filter element FA-1632 FA-1632 FA-1632Battery-standard /(auxiliary)BX
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number/ FordspecificationBrake fluidBetween MINand MAX onreserv
Item Capacity Ford part nameFord part number/ FordspecificationEngine coolant-diesel engine1Refer to the 6.0L and 6.4L Power Stroke Direct InjectionTu
Setting the clock: Press and hold CLK until the hours begin to flash.Press/ / SEEK to manually increase/decrease the hours.Press CLK again to set the
Item Capacity Ford part nameFord part number/ FordspecificationAutomatic transmission fluidTorqShift (5–speed)18.8 quarts(17.7L)3Motorcraft威MERCON威 LV
Item Capacity Ford part nameFord part number/ FordspecificationDana conventional axle fluidM60 (M248)E-150/E-3506.2 pints (2.9 L)7SAE 80W-90Premium Re
Item Capacity Ford part nameFord part number/ FordspecificationFuel tank–all regular andextended length vans and wagons35.0 gallons(132.4L)——Fuel tank
ENGINE DATAEngine14.6L V8 Engine 5.4L V8 Engine6.8L V10EngineCubic inches 281 330 415Required fuel87 octane orE85287 octane orE85287 octaneFiring orde
• 4.6L V8, 5.4L V8 and 6.8L V10 engines with A/CIDENTIFYING YOUR VEHICLESafety Compliance Certification Label(complete Ford built vehicles)The Nationa
Vehicle identification number (VIN)The VIN is located on the driver side instrument panel or on thecertification label. It contains the following info
TRANSMISSION CODE DESIGNATIONSYou can find a transmission code on the Safety Compliance CertificationLabel. The following table tells you which transm
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
Peace of mindKeyless entry keypadRemote startVehicle security systemsFor maximum vehicle performance, keep the following information inmind when addin
FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on
1. / (Tuner): Press tomanually go up or down the radiofrequency. Also use in menu modeto select various settings.In satellite radio mode (if equipped)
Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With
Ford Extended Service Plan3212010 Econoline (eco)Owners Guide, 2nd PrintingUSA (fus)
AAccessory delay ...65AdvanceTrac ...200Air cleaner filter ...305–307Airbag supplemental
Cleaning your vehicleengine compartment ...264exterior ...267instrument panel ...265inter
filter, specifications ...274, 307recommendations ...274refill capacities ...308specifications ...
JJack ...236positioning ...236storage ...236Jum
RRadio ...29, 31Rear-view camera system ...219Recommendations forattaching safety restraints forchildren ...
Tire Pressure MonitoringSystem (TPMS)Tires, Wheels and Loading ...154Tires ...136–137, 236alignment ...
an audible prompt. Press OK while SONG ALERT is in the display andthe system will take you to the channel playing the desired song. Youcan save up to
RBDS: Available only in FM mode. This feature allows you to searchRBDS-equipped stations for a certain category of music format:CLASSIC, COUNTRY, INFO
TRACK/FOLDER MODE: Available only on MP3 discs in CD mode.In track mode, pressSEEK, SEEK to scroll through all tracks onthe disc.In folder mode, press
6. / OK(Play/Pause): This control isoperational in CD/MP3 mode. Whena CD/MP3 is playing, press to pause or play the current CD/MP3. TheCD/MP3 status w
In satellite radio mode (if equipped), there are 18 available presets,six each for SAT1, SAT2 and SAT3. To save satellite channels in yourmemory prese
17. (CD eject): Press to eject aCD.18. CD slot: Insert a CD label sideup in the CD slot.Auxiliary input jack (if equipped)WARNING: Driving while distr
2. An audio extension cable with stereo male 1/8 in. (3.5 mm)connectors at each endTo play your portable music player using the auxiliary input jack:1
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
moving. Also, the portable music player should be stored in a securelocation, such as the center console or the glove box, when the vehicle isin motio
GENERAL AUDIO INFORMATIONRadio frequencies:AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio
CD units are designed to play commercially pressed 4.75 in(12 cm) audio compact discs only. Due to technicalincompatibility, certain recordable and re
• MP3 folder mode represents a folder structure consisting of one levelof folders. The CD player numbers all MP3 tracks on the disc (notedby the .mp3
roof of your vehicle. The vehicle roof provides the best location for anunobstructed, open view of the sky, a requirement of a satellite radiosystem.
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio forthe selectedchannel.No action required. Thisme
Radio Display Condition Action RequiredNO TEXT Categoryinformation notavailable.Category information notavailable at this time onthis channel. The sys
HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature sele
Operating tips• To reduce fog build-up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build-up
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Daytim
Flash-to-passPull toward you slightly to activateand release to deactivate.PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and
To adjust the headlamps:1. Park your vehicle on a level surface about 25 feet (7.6 meters) awayfrom a vertical plain surface (3). Check your headlamp
7. On the wall or screen, locate the high intensity area of the beampattern. The left edge of the high intensity area should be even with thevertical
5. Locate the vertical adjuster onthe back of each headlamp, then usea long Phillips #2 screwdriver toturn the adjuster eithercounterclockwise (to adj
Cargo lampsThe dome portion of the cargolamp, the center light, can be turnedon when the headlamp control isrotated fully counterclockwise orwhen any
Examples of unacceptable moisture (usually caused by a lamp waterleak) are:• Water puddle inside the lamp• Large water droplets, drip marks or streaks
Function Number ofbulbsTrade numberDome lamp (standard) 1 912Map/reading lamp 2 211-2All replacement bulbs are clear in color except where noted.To re
Note: If the bulb is accidentally touched, it should be cleaned withalcohol before being used.To install the new bulb, follow the removal procedures i
Sealed beam3. Rotate the bulb socket counterclockwise and remove.4. Carefully pull the bulb straight out of the socket.To complete installation, follo
PERCHLORATE MATERIALCertain components of this vehicle such as airbag modules, seat beltpretensioners, and button cell batteries may contain Perchlora
4. Carefully pull the bulb straight out of the socket.To complete installation, follow the removal procedures in reverse order.Replacing high-mount br
Replacing stop/turn/tail/side marker/backup lamp bulbsThe stop/turn/tail/side marker/backup lamp bulbs are located in the taillamp assembly. Follow th
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT STEERING WHEELTo adjust the steering wheel:1. Pull and hold the steering wheelrelease control toward you.2. Move the steering wheel up ordown unt
To prevent the fuse from being blown, do not use the power point(s)over the vehicle capacity of 12 VDC/180W. If the power point is notworking, a fuse
One-touch downAllows the driver’s window to openfully without holding the controldown. Press the switch completelydown to the second detent andrelease
Note: If equipped with a reverse camera system, a video image willdisplay in the mirror or the Navigation system display (if equipped)when the vehicle
Spotter mirror on telescopingmirror (if equipped)The spotter mirror has a swivel thatallows it to tilt up and down, andalso to tilt left and right to
WARNING: Do not use the speed control in heavy traffic or onroads that are winding, slippery or unpaved.Using speed controlThe speed controls are loca
Increasing speed while using speed controlTo increase the set speed:• Press and hold SET/ACCEL until you get to the desired speed, thenrelease. You ca
Notice to owners of diesel-powered vehiclesRead the 6.0 and 6.4 Liter Power Stroke Direct Injection Turbo DieselOwner’s Guide Supplement for informati
Navigation system/SYNC威 handsfree control features (ifequipped)Presscontrol briefly until thevoiceicon appears on theNavigation display to use the voi
They are coded as follows:Switch Circuit number Wire color FuseAUX 1 CAC05 Yellow 30AAUX 2 CAC06 Green withBrown Trace30AAUX 3 CAC07 Violet withGreen
KEYSThe key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency.If
The autolock feature repeats when:• any door is opened then closed while the ignition is in the on positionand the vehicle speed is 9 mph (15 km/h) or
Autounlock featureAfter the autolock feature has locked the doors, the autounlock featurewill unlock all the doors when:• the vehicle has then come to
7. Turn the ignition off. The horn will chirp once to confirm theprocedure is complete.Back cargo door lock (if equipped)The passenger side rear cargo
• The only way to unlock the side or back cargo doors fromoutside vehicle is with the key.For vehicles equipped with manual door locks:• The front doo
• The rear door handle is located inthe rear door below the glass.To open the side or back cargo doors from the inside:1. Unlock the E-Guard Cargo Pro
The remote entry system allows youto lock or unlock all vehicle doorswithout a key.Note: The lock and unlock featureswork when the ignition is in anyp
vehicle has switched to one step unlocking. Repeat the procedure toswitch back to two-step unlocking.Locking the doors1. Press and release to lock all
Using your vehicle as a stationary power source (PTO)Refer to the Driving chapter for more information and guidelines foroperating a vehicle equipped
2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery.Note: Please refer to localreg
3. Cycle eight times rapidly (within 10 seconds) between the 3 (off)position and 4 (on). Note: The eighth turn must end in the 4 (on)position.4. The d
Your vehicle comes with two coded keys; additional coded keys may bepurchased from your authorized dealer. The authorized dealer canprogram your spare
Automatic armingThe vehicle is armed immediately after switching the ignition to the offposition.Automatic disarmingSwitching the ignition to the on p
2. Turn ignition from the 4 (on) position back to the 3 (off) position inorder to remove the first coded key from the ignition.3. After three seconds
SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o
Adjusting the front manual seat (if equipped)WARNING: Never adjust the driver’s seat or seatback when thevehicle is moving.WARNING: Always drive and r
Using the manual lumbar support (if equipped)The lumbar support control islocated on the inboard side of thedriver’s seat.Turn the lumbar support cont
Press the control to move the seatforward, backward, up or down.REAR SEATSRear captains chair adjust — passenger side onlyPull the lever to adjust the
Quick-release captains chair(7 passenger configuration- second row only)To remove the seat:1. Disengage the lap/shoulder beltfrom the seat by insertin
Ford of Canada do not access event data recorder informationwithout obtaining consent, unless pursuant to court order orwhere required by law enforcem
1. Position the seat to the floormount.2. Pull the seat latch handle downward to lock the seat in position.3. Make sure the safety belt is not twisted
2. Find the clips attached near theends of the lap/shoulder belts.3. Clip the end of the belt to thestationary portion of the shoulderbelt coming out
4. With assistance, pull the LH/RH seat latch release straps (1) (locatedbehind the latch mechanisms) to release the latch from the rear strikers.5. L
4. Engage the front LH/RH hooks to the LH/RH front striker pins.5. After the front LH/RH hooks are engaged to the LH/RH front strikerpins, pull LH/RH
WARNING: It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision, people riding inthese areas are more likely
• Front and rear seats2. To unfasten, push the release button and remove the tongue from thebuckle.• Front and rear seatsAll safety restraints in the
equipped). Children 12 years old and under should be properlyrestrained in a rear seating position whenever possible. Refer to Safetyrestraints for ch
WARNING: BELT AND RETRACTOR ASSEMBLY MUST BEREPLACED if the safety belt assembly “automatic lockingretractor” feature or any other safety belt functio
Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occup
If... Then...The driver’s safety belt is notbuckled approximately5 seconds after the safety beltwarning light has turned off...The Belt-Minder威 featur
Commentaires sur ces manuels