Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 16Entertainment Systems 18How to get going 18AM/FM stereo with CD 22AM/FM stereo
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
Autounlock featureThe autounlock feature will unlock all the doors when:• the ignition is in the on position, all the doors are closed, and thevehicle
6. To enable/disable the autounlock feature, press the lock control, thenpress the unlock control. The horn will chirp once if autounlock wasdeactivat
• When the childproof door locks are set, the rear doors cannot beopened from the inside.• The rear doors can be opened from the outside when the powe
WARNING: Do not leave children, unreliable adults, or animalsunattended in the vehicle. On hot days, the temperature in thetrunk or vehicle interior c
The IKT allows you to:• remotely unlock the vehicledoors.• remotely lock all the vehicledoors.• remotely open the trunk.• activate the personal alarm.
two stage unlock allows all vehicle doors to unlock simultaneously). Theturn lamps will flash twice to indicate that two-stage unlock was enabledor di
Activating the memory featureTo activate this feature:1. Position the seat, mirrors and adjustable pedals to the desiredpositions.2. Press and hold ei
3. Insert the new battery. Refer tothe instructions inside the IKT forthe correct orientation of thebattery. Press the battery down toensure that the
Perimeter lamps illuminated entryWith the Integrated Keyhead Transmitter system, the following items willilluminate when the control on the transmitte
6. Press the power door unlock control twice within five seconds. Note:The horn will chirp once to indicate the perimeter lighting feature hasbeen dea
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
SECURICODE™ KEYLESS ENTRY SYSTEMYou can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• open the trunk.• recall memory
Erasing personal code1. Enter the factory set 5–digit code.2. Within five seconds, press the 1 • 2 on the keypad and release.3. Press and hold the 1 •
Standard SecuriLock威 keys without remote entry transmitterfunctionality can also be purchased from your authorized dealer ifdesired. The authorized de
Automatic armingThe vehicle is armed immediately after switching the ignition to the offposition.The theft indicator will flash everytwo seconds to ac
Tips:• Only use Integrated Keyhead Transmitters (IKTs) or standardSecuriLock威 keys.• You must have two previously programmed coded keys (keys thatalre
Integrated Keyhead Transmitter). The theft indicator light will illuminatefor three seconds and then go out to indicate successful programming.If the
• Press the 7 • 8 and 9 • 0controls on the keyless entry padat the same time to lock thedoors (driver’s door must beclosed).There is a 20 second count
SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o
Push release button to lower headrestraint.Using the manual lumbar support (if equipped)The lumbar support control islocated on the outboard side of t
WARNING: Cover sharp edges on the load and properly securethe load to prevent injury to occupants from shifting load duringsudden stops.WARNING: Befor
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A wa
Pull lever up to adjust seatback.WARNING: Beforereturning the seatback to itsoriginal position, make sure thatcargo or any objects are nottrapped behi
WARNING: To reduce the risk of possible serious injury: Do nothang objects off seat back or stow objects in map pocket (ifequipped) when a child is in
Press the control (if equipped) torecline the seatback forward orrearward.Heated seats (if equipped)WARNING: Persons who are unable to feel pain to th
Memory seat/power mirrors/adjustable pedals (if equipped)This system allows automaticpositioning of the driver seat,outside rearview mirrors andadjust
The head restraints can be movedup by pulling up on the headrestraint.Push the release button to lowerhead restraint.Split-folding rear seatOne or bot
WARNING:Before returning the seatback to its original position,make sure that cargo or any objects are not trapped behind theseatback. After returning
• Driver’s seat position sensor.• Front passenger sensing system• “Passenger airbag off” or “pass airbag off” indicator lamp• Front crash severity sen
levels of crash severity and modify the deployment strategy of thedual-stage airbags and safety belt pretensioners.Driver’s seat position sensorThe dr
allows your Personal Safety System威 to tailor the airbag deployment andsafety belt pretensioner activation depending upon safety belt usage.Front safe
Safety belt precautionsWARNING: Always drive and ride with your seatback uprightand the lap belt snug and low across the hips.WARNING: To reduce the r
WARNING: Under engine misfire conditions, excessive exhausttemperatures could damage the catalytic converter, the fuelsystem, interior floor coverings
WARNING: Front and rear seat occupants, including pregnantwomen, should wear safety belts for optimum protection in anaccident.Combination lap and sho
WARNING: Failure to inspect and replace if necessary the beltand retractor assembly after an accident could increase the riskof injury in a collision.
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
WARNING: Position the safety belt height adjusters so that thebelt rests across the middle of your shoulder. Failure to adjustthe safety belt properly
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war
If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the onposition or less than1-2 minutes h
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate
Before following the procedure, make sure that:• The parking brake is set• The gearshift is in P (Park)• The ignition switch is in the off position• T
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The airbag supplemental restraint system (SRS) is designed to work inconjunction with the safety belts to he
Airbag readiness: If this light failsto illuminate when the ignition isturned to on, continues to flash orremains on, have the systemserviced immediat
WARNING: All occupants of the vehicle, including the driver,should always properly wear their safety belts, even when an airbag supplemental restraint
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
• driver and front passenger safety belt pretensioner• a readiness light and tone.• diagnostic module.• the electrical wiring which connects the compo
The front passenger sensing system will turn off the passenger seat sideairbag if:• the seat is empty and safety belt is unbuckled.The front passenger
• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LightPassen
ObjectsPass Airbag OffIndicator LightPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase
In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi
A difficulty with the system is indicated by one or more of the following:• The readiness light (same lightfor front and side airbag system)will eithe
How does the side airbag system work?The design and development of the side airbag system includedrecommended testing procedures that were developed b
Low tire pressure warning:Illuminates when your tire pressureis low. If the light remains on atstart up or while driving, the tirepressure should be c
WARNING: Several air bag system components get hot afterinflation. Do not touch them after inflation.WARNING: If the sideairbag has deployed, theairba
WARNING: All occupants of the vehicle including the drivershould always wear their safety belts even when an airbag SRSand Safety Canopy威 system is pr
The Safety Canopy威 system, in combination with safety belts, can helpreduce the risk of severe injuries in the event of a significant side impactcolli
WARNING: If the Safety Canopy威 system has deployed, theSafety Canopy威 will not function again unless replaced. TheSafety Canopy威 system (including the
SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme
Recommendations for Safety Restraints for ChildrenChild size, height, weight, orageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb
Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe
WARNING: Always carefully follow the instructions andwarnings provided by the manufacturer of any child restraint todetermine if the restraint device
Transporting childrenAlways make sure your child is secured properly in a device that isappropriate for their age, height and weight. All children are
When installing a child safety seat:• Review and follow the informationpresented in the Airbagsupplemental restraint system(SRS) section in this chapt
High beams: Illuminates when thehigh beam headlamps are turned on.Key-in-ignition warning chime: Sounds when the key is left in theignition in the off
WARNING: Depending on where you secure a child restraint,and depending on the child restraint design, you may blockaccess to certain safety belt buckl
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up
method eliminates the need to use safety belts to attach the child seat,however the safety belt can still be used to attach the child seat. Forforward
them in each outboard seating position and the third in thecenter using the lap/shoulder belt, OR you can use the LATCHlower anchors for the center ch
Attaching child safety seats with tether strapsMany forward-facing child safety seats include a tether strap whichextends from the back of the child s
3. Open the tether anchor cover.4. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safety seat maynot
Booster seats position a child so that vehicle lap/shoulder safety belts fitbetter. They lift the child up so that the lap belt rests low across the h
Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
WARNING: Never remove the coolant reservoir cap while theengine is running or hot.Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel
Move a child to a different seating location if the shoulder belt does notstay positioned on the shoulder during use.Follow all instructions provided
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli
WARNING: The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydro
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
WARNING: Under-inflation is the most common cause of tirefailures and may result in severe tire cracking, tread separationor ⬙blowout⬙, with unexpecte
Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo
Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w
• Do not run over curbs or hit the tire against a curb when parkingWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the
AUDIO SYSTEMSQuick start — How to get goingWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly
• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/All Wheel Drive (AWD)vehicles (
Sometimes irregular tire wear can be corrected by rotating the tires.Note: If your tires show uneven wear ask an authorized dealer to checkfor and cor
3. 65: Indicates the aspect ratio which gives the tire’s ratio of height towidth.4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or ri
8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n
13. Maximum Permissible Inflation Pressure: Indicates the tiremanufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw
Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti
When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.
Listening to satellite radio (if equipped)1. If the audio system is turned off,press VOL-PUSH to turn the radioon. Turn VOL-PUSH to adjust thevolume.N
Low TirePressureWarning LightPossiblecauseCustomer Action RequiredFlashing WarningLightSpare tire inuseYour temporary spare tire is inuse. Repair the
under-inflated, carefully drive the vehicle to the nearest location whereair can be added to the tires. Inflate all the tires to the recommendedinflat
• Do not exceed 30 mph (48 km/h) with tire cables on your vehicle.VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the prope
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or performance, e
WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the
to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1,400 - (2 x 220) -(12 x 100) = 1,40
HitchesDo not use hitches that clamp onto the vehicle bumper. Use a loadcarrying hitch. You must distribute the load in your trailer so that10–15% of
Locks and Security 96Keys 96Locks 97Anti-theft system 111Seating and Safety Restraints 117Seating 117Safety restraints 125Airbags 139Child restraints
For a single CD system, if a discis not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the
• It is recommended to select the L (Low) gear position when additionalengine braking is needed. In situations such as prolonged downhilldriving on st
Front Wheel Drive (FWD) vehicles:Tow your Front Wheel Drive vehicle with all four wheels on the groundor with the front wheels off the ground by using
STARTINGPositions of the ignition1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accesso
WARNING: Do not start your vehicle in a closed garage or inother enclosed areas. Exhaust fumes can be toxic. Always openthe garage door before you sta
• Make sure the gearshift lever is inP (Park).3. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminat
2. Turn the key to 4 (start), then release the key as soon as the enginebegins cranking. Your vehicle has a computer assisted cranking systemthat assi
WARNING: To reduce the risk of electrical shock, do not useyour heater with ungrounded electrical systems or two-pronged(cheater) adapters.Prior to us
How to use the engine block heaterEnsure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth.Depending on the type
Brake AssistThe Brake Assist system provides full braking force during panic brakingsituations. It detects a rapid application of the brake pedal and
WARNING: Always set the parking brake fully and make surethat the gearshift is securely latched in P (Park).The parking brake is not recommended to st
While in folder mode, pressFOLDERto access the nextfolder on MP3 discs, if available.Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe
WARNING: Remember that even advanced technology cannotdefy the laws of physics. It’s always possible to lose control of avehicle due to inappropriate
AdvanceTrac威 system to operate. If the “sliding car” icon illuminatessteadily, verify that the AdvanceTrac威 system is not manually disabled bypressing
system will regain all features. Anti-lock braking, and ESC are notaffected by this condition and will continue to function during thecool-down period
If you switch off the AdvanceTrac威 system the AdvanceTrac “Off” buttonwill illuminate and the sliding car⬙ iconwill illuminate steadily.Pressing the A
If the steering wanders or pulls, check for:• an improperly inflated tire• uneven tire wear• loose or worn suspension components• loose or worn steeri
WARNING: Do not drive your vehicle until you verify that thebrakelamps are working.WARNING: Always set the parking brake fully and make surethe gearsh
P (Park)This position locks the transmission and prevents the front wheels fromturning.To put your vehicle in gear:• Press the brake pedal• Move the g
D (Drive) with Overdrive Cancel and Grade AssistPressing the transmission controlswitch on the side of the gearshiftlever activates two features at th
• The O/D OFF lamp in the instrument cluster will not be illuminated.• The transmission will operate in gears one through six.O/D (overdrive mode) is
The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to th
AM/FM Single CD/MP3 satellite compatible sound system(if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and
ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED)Your vehicle may be equipped with a full-time All Wheel Drive (AWD)system. The AWD system is an active syste
If your vehicle goes off the edge of the pavement• If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ea
Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle (i.e.,
When driving through water, determine the depth; avoid water higherthan the bottom of the wheel rims (if possible) and proceed slowly. If theignition
When climbing a steep slope or hill, start in a lower gear rather thandownshifting to a lower gear from a higher gear once the ascent hasstarted. This
your vehicle is equipped with a four wheel anti-lock brake system (ABS),do not “pump” the brakes. Refer to the Brakes section of this chapterfor addit
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co
After an accident, if the engine cranks but does not start, this switchmay have been activated.The fuel pump shut-off switch islocated in the front pa
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
In CATEGORY mode, press / to scroll through the list ofavailable SIRIUS channel Categories (Pop, Rock, News, etc.). Refer toCategory under Menu for fu
Passenger compartment fuse panelThe fuse panel is located under the instrument panel to the left of thesteering wheel.The fuses are coded as follows.F
Fuse/RelayLocationFuse AmpRatingProtected Circuits8 10A Low beam headlamps (right)9 15A Interior lights, Cargo lamps10 15A Backlighting, Puddle lamps1
Fuse/RelayLocationFuse AmpRatingProtected Circuits36 5A PATS module37 10A Climate control38 20A Subwoofer (Audiophile radio)39 20A Radio40 20A Not use
The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPower Circuits1 80A* SPDJB power2 80A* SPDJB power3 30A* Front wipers4 — N
Fuse/RelayLocationFuse AmpRatingPower Circuits16 20A** Power point (console)17 10A** Alternator18 — Not used19 — Not used20 40A* Rear defroster21 30A*
Fuse/RelayLocationFuse AmpRatingPower Circuits44 — Not used45 10A** Speed control deactivate switch,Mass air flow sensor, Inlinemodule VPWR246 10A** A
WARNING: The use of tire sealants may damage your TirePressure Monitoring System and should not be used.WARNING: Refer to Tire Pressure Monitoring Sys
Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following:• Handling, stability and braki
Stopping and securing the vehicle1. Park on a level surface, set theparking brake and activate hazardflashers.2. Place gearshift lever in P (Park)and
WARNING: To help prevent the vehicle from moving when youchange a tire, be sure to place the transmission in P (Park), setthe parking brake and block
• DELETE SONG: Press OK to delete a song from the system’smemory. Press/ to cycle through the saved songs. When thesong appears in the display that yo
3. Put the jack in the jack notchnext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is completely off theground.Note: DO
Stowing the tire and jack1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown.
If you are stowing the flat tire:1. Remove the extension bolt fromthe exterior pocket of the felt bag.2. Install the jack as shown inStep 4 under Stow
Note: Inspect the wheel pilot holeprior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean r
4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level.5. Tu
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
If the vehicle is towed by other means or incorrectly, vehicledamage may occur.Ford Motor Company produces a towing manual for all authorized towtruck
To search for specific RBDS music categories: When the desiredcategory appears in the display, press/ to find the desired type,then press and releaseS
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized
In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph
In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext
procedure outlined on the first page of the Customer Assistance section,you may be eligible to participate in the BBB AUTO LINE program.The BBB AUTO L
The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have
If you cannot find unleaded fuel or can only get fuel with an anti-knockindex lower than is recommended for your vehicle, contact a regionaloffice or
Obtaining a French owner’s guideFrench Owner’s Guides can be obtained from your authorized dealer orby writing to:Ford Motor Company of Canada, Limite
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is
WAXING• Wash the vehicle first.• Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your aut
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
COMPRESS (Compression): Available only in CD/MP3 mode. PressMENU until COMPRESS ON/OFF appears in the display. Use / totoggle ON/OFF. When COMPRESS is
• For routine cleaning, use Motorcraft Detail Wash (ZC-3-A).• If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42).• For plas
INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENSClean the instrument panel, interior trim areas and cluster lens with aclean and damp white cotton clot
• If grease or tar is present on the material, spot-clean the area firstwith Motorcraft Spot and Stain Remover (ZC-14). In Canada, useMotorcraft Multi
FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column.2. Go to th
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.5L V6 ENGINE1. Power steering fluid reservoir2. Engine coolant reservoir3. Brake fluid reservoir4. B
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
CHANGING THE WIPER BLADES1. Pull the wiper blade and armaway from the glass.2. Squeeze the locking tabs torelease the blade from the arm andpull the b
5. Locate and carefully remove theengine oil level dipstick.6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil l
7. SHUFFLE: Press SHUFFLE toengage shuffle mode. SHUFFLE ONwill appear in the display. If youwish to engage shuffle mode right away, press SEEK to beg
• Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine isoverfilled, some oil must beremoved from the e
to the current engine and emission system protection standards and fueleconomy requirements of the International Lubricant Standardization andApproval
If you see any corrosion on the battery or terminals, remove the cablesfrom the terminals and clean with a wire brush. You can neutralize theacid with
1. With the vehicle at a complete stop, set the parking brake.2. Put the gearshift in P (Park), turn off all accessories and start theengine.3. Run th
Your vehicle was factory-filled with a 50/50 engine coolant and waterconcentration. If the concentration of coolant falls below 40% or above60%, the e
WARNING: Do not add engine coolant when the engine is hot.Steam and scalding liquids released from a hot cooling systemcan burn you badly. Also, you c
coolant degas system with a pressurized cap, or if it is necessary toremove the coolant pressure relief cap on the radiator of a vehicle withan overfl
Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant since a Ford-approved recycling process is not yet avai
Vehicles driven year-round in non-extreme climates should use a 50/50mixture of engine coolant and distilled water for optimum cooling systemand engin
WARNING: Fail-safe mode is for use during emergencies only.Operate the vehicle in fail-safe mode only as long as necessary tobring the vehicle to rest
13. TEXT/SCAN: In radio andCD/MP3 mode, press and hold fora brief sampling of radio stations orCD tracks. Press again to stop.In MP3 mode, press and r
WARNING: Automotive fuels can cause serious injury or deathif misused or mishandled.WARNING: Gasoline may contain benzene, which is acancer-causing ag
WARNING: When refueling always shut the engine off andnever allow sparks or open flames near the filler neck. Neversmoke while refueling. Fuel vapor i
Fuel filler capYour fuel tank filler cap has an indexed design with a 1/4 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref
WARNING: If you do not use the proper fuel filler cap,excessive vacuum in the fuel tank may damage the fuel systemor cause the fuel cap to disengage i
Fuel qualityIf you are experiencing starting, rough idle or hesitation driveabilityproblems, try a different brand of unleaded gasoline. “Premium”unle
ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform
Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers).2. Each time you fill the tan
• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between the top gears occurs. Unnecessaryshifting of this type co
is not supplied with your vehicle. The EPA fuel economy estimatesshould be your guide for the fuel economy comparisons with othervehicles. Your fuel e
Do not make any unauthorized changes to your vehicle or engine. Bylaw, vehicle owners and anyone who manufactures, repairs, services,sells, leases, tr
17. (CD eject): Press to eject aCD.18. CD slot: Insert a CD label sideup in the CD slot.Premium/Premium plus AM/FM in-dash six CD/MP3 satellitecompati
Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect
1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center o
Automatic transmission fluid expands when warmed. To obtain anaccurate fluid check, drive the vehicle until it is warmed up(approximately 20 miles [30
High fluid levelFluid levels above the safe rangemay result in transmission failure.An overfill condition of transmissionfluid may cause shift and/ore
Changing the air filter element1. Release the clamps that securethe air filter housing cover.2. Carefully separate the two halvesof the air filter hou
MOTORCRAFT PART NUMBERSComponent 3.5L V6 EngineEngine air filter element FA-1884Battery BXT-59Oil filter FL-400-S or FL-500-S3PCV valve1Spark plugs21T
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItems CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationBrake fluidBetween MAX a
Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine oil 5.5 quarts (5.2L)Motorcraft SAE 5W-20Premium SyntheticBlend Mo
Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationFuel tank20.5 gallons(77.6L) AWD,PZEV AWD andPZEV FWD——20.0 gallons(75.7L
ENGINE DATAEngine 3.5L-DOHC V6 engineCubic inches 214Required fuel 87 octaneFiring order 1–4–2–5–3–6Spark plug gap 0.052–0.056 inch (1.32–1.42 mm)Igni
Customer Assistance 250Reporting safety defects (U.S. only) 256Reporting safety defects (Canada only) 256Cleaning 257Maintenance and Specifications 26
1. / (Tune/Disc selector):In radio mode, press to manuallygo up () or down ( )theradio frequency. Press and hold fora fast advance through radio frequ
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
Peace of mindRemote startVehicle security systemsWheel locksFor maximum vehicle performance, keep the following information inmind when adding accesso
AAccessory delay ...71AdvanceTrac ...209Air cleaner filter ...293–295Air conditioning ..
plastic parts ...259washing ...257waxing ...258wheels ...
Exhaust fumes ...205FFail safe cooling ...278Fluid capacities ...296Fog lamps ...
KKeyless entry systemautolock ...98keypad ...110locking and unlocking doors ..111p
fluid, specifications ...296Power Windows ...69RRadio ...18, 22, 29Recommendations
Tire Pressure MonitoringSystem (TPMS)Roadside Emergencies ...235Tires, Wheels and Loading ...186Tires ...171–172, 235
playing on any satellite radio channel, the system will alert you withan audible prompt. Press OK while SONG ALERT is in the display andthe system wil
RBDS: Available only in FM mode. This feature allows you to searchRBDS-equipped stations for a certain category of music format:CLASSIC, COUNTRY, INFO
Track/Folder Mode: Available only on MP3 discs in CD mode. In TrackMode, pressingSEEK will scroll through all tracks on the disc.In Folder mode, press
6. OK:(Play/Pause): Pressthis control to play or pause thecurrent CD.OK: Use in various menu selections.Your vehicle may be equipped with special phon
memory presets, tune to the desired channel then press and hold apreset control until sound returns.Satellite radio is available only with a valid SIR
17. LOAD: Toloadadiscintothesystem, press LOAD. Select a slotnumber using memory presets 1–6.When the display reads LOAD CD#,load the desired disc, la
Your vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicplayer to the in-vehic
Troubleshooting:1. Do not connect the audio input jack to a line level output. Line leveloutputs are intended for connection to a home stereo and are
Your vehicle may be equipped with aUSB port inside your center console.This feature allows you to plug inmedia playing devices, memorysticks, and also
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C
CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio forthe selectedchannel.No action required. Thisme
Radio Display Condition Action RequiredNO TEXT Categoryinformation notavailable.Category information notavailable at this time onthis channel. The sys
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Airflow selec
4. Rear defroster: Press to activate/deactivate rear window defroster.Refer to Rear window defroster in this section for more information.5. A/C: Pres
4. Set the fan speed to the highest setting.5. Direct the outer instrument panel vents toward the side windows.DUAL ZONE AUTOMATIC TEMPERATURE CONTROL
When the ignition switch is turned off and back on, the climate systemwill return to the recirculated air mode only if the A/C button light isillumina
Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti
Dual Zone Automatic Temperature Control with heated seats(if equipped)1.Defrost: Distributes outside air through the windshield defrosterand demister
automatically with selection of MAX A/C or can be engaged manually inany other airflow selection except(defrost). Recirculation may turnoff automatica
15. Driver temperature control: Press to increase/decrease thetemperature on the driver side of the cabin. Also adjusts the passengerside temperature
To aid in side window defogging/demisting in cold weather:1. Select.2. Press A/C.3. Adjust the temperature to the warmest setting.4. Set the fan speed
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the low beam headlampso
3. Turn the ignition switch to on and then back to off.4. Turn the headlamp control to the autolamp position. The headlampswill turn on.5. Wait the de
Flash to passPull toward you to activate andrelease to deactivate.Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced outpu
Note: If the battery is disconnected, discharged, or a new battery isinstalled, the dimmer switch requires re-calibration. Rotate the dimmerswitch fro
5. Locate the vertical adjuster oneach headlamp. Using a Phillips #2screwdriver, turn the adjuster eitherclockwise (to adjust down) orcounterclockwise
Your vehicle may also have readinglamps within the rear dome lamp(s).Press the switches on either side ofthe dome lamp to turn on thelamps.BULB REPLAC
BREAKING-IN YOUR VEHICLEYour vehicle does not need an extensive break-in. Try not to drivecontinuously at the same speed for the first 1,000 miles (1,
Function Number of bulbsTradenumberHeadlamp high beam 2 9005Headlamp low beam 2 H11Front park/turn lamp 23457A or3457AK(amber)Sidemarker lamp (front)
3. Remove the outboard rubber bootfrom the lamp assembly by pullingrearward.4. Remove the bulb socket byturning it counterclockwise andpulling it stra
Replacing front parking lamp/turn signal/sidemarker bulbs1. Make sure headlamp switch is in the off position, then open the hood.2. Reach in behind th
2. Remove the press pin and cargonet fastener (if equipped) andcarefully pull the carpet away toexpose the backside of the tail lampassembly.3. Remove
Replacing license plate lamp bulbs1. Make sure the headlamp switch isin the off position.2. Remove the two screws from thelicense plate lamp assembly.
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT STEERING WHEELTo adjust the steering wheel:1. Pull down and hold the steeringwheel release control.2. Move the steering wheel up ordown until you
INSTRUMENT PANEL STORAGE COMPARTMENTThe storage compartment may beused to secure sunglasses or similarsized objects. Press the button toopen the stora
CENTER CONSOLEYour vehicle may be equipped with a variety of console features. Theseinclude:1. Cupholders2. Utility compartment with coinholder, a cla
To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe ba
Service Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This pote
Press and pull the window switchesto open and close windows.• Push down (to the first detent)and hold the switch to open.• Pull up (to the first deten
Bounce-back (driver’s window only)When an obstacle has been detected in the window opening as thewindow is moving upward, the window will automaticall
Automatic dimming interior rear view mirrorYour vehicle is equipped with an interior rear view mirror that has anauto-dimming function. The electronic
EXTERIOR MIRRORSPower side view mirrorsWARNING: Do not adjust the mirror while the vehicle is inmotion.To adjust your mirrors:1. Rotate the control cl
The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position.Press and hold th
Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas
Resuming a set speedPress the RSM control and releaseit. This will automatically return thevehicle to the previously set speed.Increasing speed while
• Depress the brake pedal or pressCNCL (Cancel) until the desiredvehicle speed is reached, pressthe SET + control.Turning off speed controlThere are t
In AM, FM1, or FM2 mode:• Press SEEK to access thenext/previous strong station.In Satellite radio mode (ifequipped):• Press and release SEEK to access
SYNC system hands free controlfeature (if equipped)Pressbriefly to use the voicecommand feature. You will hear atone and LISTENING will appear inthe r
To access this information, special equipment must be directlyconnected to the recording modules. Ford Motor Company andFord of Canada do not access e
To open the moon roof: Press andrelease the SLIDE control, the moonroof will open automatically. Pressthe switch again to stop the moonroof.WARNING: W
HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED)The HomeLink威 Wireless ControlSystem, located on the driver’s visor,provides a convenient way toreplace
1. Position the end of yourhand-held transmitter 1–3 inches(2–8 cm) away from the HomeLink威button you wish to program (locatedon your visor) while kee
Gate Operator & Canadian ProgrammingDuring programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time for
Erasing HomeLink姞 buttonsTo erase the three programmedbuttons (individual buttons cannotbe erased):• Press and hold the two outerHomeLink威 buttons unt
Info menuThis control displays the followingcontrol displays:• Odometer• Trip Odometer• Distance to Empty• Average Fuel Economy• Trip Elapsed Drive Ti
Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in miles/gallon orliters/100 km.If you calculate
Usually, when something affects the compass readings, the compass willcorrect itself after a few days of operating your vehicle in normalconditions. I
Compass calibration adjustmentPerform the following steps on an open area free from steel structuresand high voltage lines. For optimum calibration, t
Setup menuPress this control for the followingdisplays:• System Check• Oil Life• Language• Units (English/Metric)• Autolamp Delay (if equipped)• Autol
Export unique (Non–United States/Canada) vehicle specificinformationFor your particular global region, your vehicle may be equipped withfeatures and o
To reset the oil monitoring system to 100% after each oil change(approximately 7,500 miles [12,000 km] or six months) perform thefollowing:1. Press th
1. To disable/enable the autolampdelay feature, select this functionfrom the SETUP control for thecurrent display mode.2. Press the RESET control to s
In the event of a multiple warning situation, the message center willcycle the display to show all warnings by displaying each one for severalseconds.
REAR LEFT DOOR AJAR — Displayed when the left rear door is notcompletely closed.REAR RIGHT DOOR AJAR — Displayed when the right rear door isnot comple
OIL LIFE CHANGE SOON — Displayed when the engine oil liferemaining is 10% or less. When oil life left is between 10% and 0%, theXX% OIL LIFE CHANGE SO
CARGO AREA FEATURESCargo net (if equipped)The cargo net secures lightweightobjects in the cargo area. Attach thenet to the anchors provided. Do notput
KEYSYour vehicle may be equipped withtwo Integrated KeyheadTransmitters (IKTs). The key bladefunctions as a programmed keywhich starts the vehicle and
When inserting the IKT into theignition cylinder, place your thumbon the center thumb rest of the IKTand forefinger on the logo badge onthe opposite s
Smart locksThis feature helps to prevent you from locking yourself out of the vehicleif your key is still in the ignition.When you open one of the fro
Power door lock switch autolock enable/disable procedureBefore starting, ensure the ignition is in the off position and all vehicledoors are closed. Y
Commentaires sur ces manuels