Ford 2009 F-550 v.3 Manuel d'utilisateur

Introduction 4Instrument Cluster 14Warning lights and chimes 14Gauges 21Entertainment Systems 26AM/FM stereo 26AM/FM stereo with CD 28AM/FM stereo wit

Notice to owners of pickup trucks and utility type vehiclesWARNING: Utility vehicles have a significantly higher rolloverrate than other types of vehi

2. Remove the three screws and onebolt from the top and bottom of thepark lamp/bezel assembly.3. Pull the assembly straight outdisengaging snap clip.4

3. Rotate the bulb socket counterclockwise and remove from lampassembly.4. Pull the bulb straight out of the socket.Install the new bulb(s) in reverse

Replacing front clearance and identification lamp bulbs1. Make sure the headlamps are off.2. Remove the screw and lens fromthe lamp assembly.3. Pull t

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Windshield wiper rainlamp feature (if equipped with Autolamp)When the windshield wipers are turned on during daylight, and theheadlamp control is in t

ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamp.OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehic

CENTER CONSOLE (IF EQUIPPED)Your vehicle may be equipped with a variety of console features. Theseinclude:• Utility compartment withcassette/CD holder

Under-seat storageFlip the rear seat cushion up toaccess the rear under-seat storagearea. See Seating in the Seatingand safety restraints chapter form

fuse may have blown. Refer to Fuses and relays in the RoadsideEmergencies chapter for information on checking and replacing fuses.To have full capacit

Rear Window Buffeting: When one or both of the rear windows areopen, the vehicle may demonstrate a wind throb or buffeting noise; thisnoise can be all

If your vehicle is equipped with theFord Ambulance PreparationPackage, it will be indicated on theSafety Compliance CertificationLabel. The label is l

If your vehicle is equipped with apower rear slide window, the switchis located on the instrument panelbehind the right-hand side of thesteering wheel

With microphoneThe mirror will automatically return to the normal state whenever thevehicle is placed in R (Reverse) to ensure a bright clear view whe

Heated outside mirrors (if equipped)The main mirror glass and lowerconvex spotter mirror are heated toremove ice, mist and fog. To activatethe heated

Powerfold mirror positions, from left to right: Position 1, Position 2,Position 3The powerfold mirrors may be folded forward/rearward manually to anyo

Telescoping mirrors (if equipped)The telescoping feature allows themirror to extend approximately2.75 inches (70 mm). This feature isespecially useful

Mirror mounted side turn signal indicator (if equipped)When the vehicle turn signals areactivated, the outer portion of themirror housing will blink a

The accelerator and brake pedal positions are saved when doing amemory set function and can be recalled along with the vehiclepersonality features whe

Note:• Vehicle speed may vary momentarily when driving up and down asteep hill.• If the vehicle speed increases above the set speed on a downhill, you

Reducing speed while using speed controlThere are two ways to reduce a setspeed:• Press and hold the SET - controluntil you get to the desiredspeed, t

Audio control featuresPress MEDIA to select:• AM, FM1, FM2• CD (if equipped)• DVD (if equipped)• SAT1, SAT2 or SAT3 (SatelliteRadio mode, if equipped)

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

Navigation system hands freecontrol features (if equipped)Press and hold VOICE briefly untilthe voiceicon appears on theNavigation display to use the

For further information on the Navigation system/SYNC system, refer tothe Navigation System and SYNC威 supplements.UPFITTER CONTROLS (IF EQUIPPED)Your

There will also be one power leadfor each switch found as a blunt-cutand sealed wire located below theinstrument panel and to the left ofthe steering

To open the moon roof: The moon roof is equipped with a one-touchopen feature. Press and release thecontrol. The moon roof will opento the “comfort” p

Do not use the HomeLink威 Wireless Control System with any garagedoor opener that lacks safety stop and reverse features as required byU.S. federal saf

• If the indicator light blinks rapidly for two seconds and then turnsto a constant light continue with “Programming” Steps 4 through6 to complete pro

Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet

STANDARD MESSAGE CENTER (IF EQUIPPED)With the ignition in the on position,the message center, located on yourinstrument cluster, displays textmessages

Distance to empty (DTE)Selecting this function from theINFO MENU estimatesapproximately how far you can drivewith the fuel remaining in your tankunder

Setup menuPress and hold the SELECT/RESETbutton to get into the SETUP MENUsequence from the INFO MENU forthe following displays:• Oil Life• Units (Eng

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

Units (English/Metric)1. Select this function from theSETUP MENU for the current unitsto be displayed.2. Press and hold theSELECT/RESET button to chan

5. AIR FILTER (Diesel engine only)6. DOOR AJAR7. BRAKE SYSTEM8. TBC GAIN = XX.XNO TRAILER (if equipped and no trailer connected)9. TBC GAIN = XX.XOUTP

The message center will display the last selected feature if there are nomore warning messages. This allows you to use the full functionality ofthe me

Warning display StatusCheck air filter(diesel engine only)Drain water separator(diesel engine only)Stop safely now(diesel engine only)Engine warming p

REAR RIGHT DOOR AJAR — Displayed when the rear right door isnot completely closed.XXX MILES TO E FUEL LEVEL LOW — Displayed as an earlyreminder of a l

DRAIN WATER SEPARATOR (Diesel engine only) — Displayedwhen the water separator has reached a predetermined capacity andneeds to be drained. Refer to y

DRIVE TO CLEAN EXHAUST FILTER (Diesel engine only) —Displayed when the engine control module detects the Diesel ParticulateFilter (DPF) is full of par

OPTIONAL MESSAGE CENTER (IF EQUIPPED)With the ignition in the on position,the message center, located on yourinstrument cluster, displaysimportant veh

Info menuThis control displays the followingitems:• Trip odometer A or B• Engine hour meter/odometer (ifequipped)• Distance to empty• Average fuel eco

Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in miles/gallon orliters/100 km.If you calculate

WARNING LIGHTS AND CHIMESVehicles equipped with a manual transmissionAutomatic transmission2009 F-250/350/450/550 (f23)Owners Guide, 3rd PrintingUSA (

Setup menuPress this control for the followingdisplays:• System check• Units (English/Metric)• Autolamp timer presets (ifequipped)• Autolock On/Off (i

5. AIR FILTER (Diesel engine only)6. DOOR AJAR7. BRAKE SYSTEM8. TBC GAIN = XX.XNO TRAILER (if equipped and no trailer connected)9. TBC GAIN = XX.XOUTP

Units (English/Metric)1. Select this function from theSETUP menu for the current unitsto be displayed.2. Press the RESET button tochange from English

Most geographic areas (zones) have a magnetic north compass point thatvaries slightly from the northerly direction on maps. This variation is fourdegr

8. Slowly drive the vehicle in acircle (less than 3 mph [5 km/h])until the CIRCLE SLOWLY TOCALIBRATE display changes toCALIBRATION COMPLETED. It willt

Warning messages that have been reset are divided into two categories:• They will reappear on the display 10 minutes from the reset.• They will not re

Warning display StatusCheck air filter(diesel engine only)Drain water separator(diesel engine only)Stop safely now(diesel engine only)Engine warming p

REAR RIGHT DOOR AJAR — Displayed when the rear right door isnot completely closed.FUEL LEVEL LOW — Displayed as an early reminder of a low fuelconditi

DRAIN WATER SEPARATOR (Diesel engine only) — Displayedwhen the water separator has reached a predetermined capacity andneeds to be drained. Refer to y

DRIVE TO CLEAN EXHAUST FILTER (Diesel engine only) —Displayed when the engine control module detects the Diesel ParticulateFilter (DPF) is full of par

Harley-Davidson vehiclesWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A war

TAILGATE LOCK (IF EQUIPPED)Your vehicle may be equipped with atailgate lock designed to helpprevent theft of the tailgate.• Insert ignition key and tu

4. Lower the tailgate.5. Using a screwdriver, gently prythe spring clip (on each connector)past the head of the support screw.Disconnect cable.6. Disc

• Always use grab handle when stepping up and down.• Step not intended for bare-footed use.• Keep step clean from contamination before use (e.g. snow,

2. Open the latches to release thepanels.3. Rotate the panels toward thetailgate.Repeat Steps 1–3 for the other side of the bed extender.4. Connect th

5. Ensure the latch rod is insertedinto the tailgate hole and the lockingpins on both sides are engaged intotheir holes in the pick-up box.6. Reverse

KEYSThe key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency.If

Autolock feature (if equipped)The autolock feature will lock all the doors when:• all the doors are closed,• the ignition is in the on position,• you

5. Turn the ignition back to the on position. The horn will chirp one timeto confirm programming mode has been entered and is active.6. To enable/disa

Deactivating/activating autounlock featureThere are three methods to enable/disable this feature:• Through your authorized dealer,• by using a power d

4. Press and hold the 3 • 4. While holding the 3 • 4, press and releasethe 7 • 8. While still holding the 3 • 4, press and release the 7 • 8asecond ti

chapter. If the light is blinking, engine misfire is occurring which coulddamage your catalytic converter. Drive in a moderate fashion (avoidheavy acc

The typical operating range for your remote entry transmitter isapproximately 33 feet (10 meters). A decrease in operating range couldbe caused by:• w

Switching from two step to one step door unlockingYour vehicle comes with two step unlocking enabled. Unlocking can beswitched between two step and on

Activating the memory featureTo activate this feature:1. Position the seat, adjustable pedals and mirrors to the positiondesired.2. Press and hold eit

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery.Note: Please refer to localreg

To reprogram the remote entrytransmitters:1. Ensure the vehicle iselectronically unlocked.2. Put the key in the ignition.3. Cycle eight times rapidly

Deactivating/activating perimeter lamps illuminated entryYou may enable/disable this feature by having your vehicle serviced byyour authorized dealer.

The dome lamp control (if equipped) must not be set to the off positionfor the illuminated entry system to operate.The inside lights will not turn off

5. The doors will again lock then unlock to confirm that your personalkeycode has been programmed to the module.Tips:• Do not set a code that uses fiv

SECURILOCK™ PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED)SecuriLock™ passive anti-theft system is an engine immobilizationsystem. This system is designed to

Vehicles without the SecuriLock™ Passive Anti-theft system behave asfollows:• When the ignition is in the off position, the indicator will not flash.•

Airbag readiness: If this light failsto illuminate when ignition is turnedto on, continues to flash or remainson, have the system servicedimmediately

1. Insert the first previouslyprogrammed coded key into theignition and turn the ignition fromthe 1 (off) position to the 3 (on)position (maintain ign

PERIMETER ALARM SYSTEM (IF EQUIPPED)The perimeter anti-theft system will warn you in the event of anunauthorized entry to your vehicle.If there is any

SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o

Full bench seat (if equipped)• Lift the release bar to move theseat forward or backward. Ensurethat the seat is relatched intoplace.• Pull up on the l

40/20/40 front seat armrest and console (if equipped)To release the armrest, pull forwardon the strap and pull the armrestdown.To gain access to the s

Captain’s chair (if equipped)• Lift the bar to move the seatforward or rearward. Make surethat the seat is relatched intoplace.• To recline the seatba

Press front to raise or lower thefront portion of the seat cushion.Press rear to raise or lower the rearportion of the seat cushion.Press the control

Heated seats (if equipped)The heated seat control is located on the climate control panel.WARNING: Persons who are unable to feel pain to the skinbeca

To recall a memory position:• Press and release either memory 1 button or memory 2 button.A position can be recalled:• in any gearshift position if th

Push control to lower head restraint.WARNING: To minimize the risk of neck injury in the event of acrash, the driver and passenger occupants should no

Powertrain malfunction/Reducedpower/Electronic throttlecontrol (RTT): Displays when theengine has defaulted to a“limp-home” operation or when atransmi

To flip the seat cushion up, pullup on the lever located on the sideof the seat cushion to rotate thecushion up until it locks into avertical storage

To gain access to the 60/40 loadfloor, store the cushion in theupright locked position. Pull up onthe straps located at the sides of theload floor, an

WARNING: Each seating position in your vehicle has a specificsafety belt assembly which is made up of one buckle and onetongue that are designed to be

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.Vehicle sensitive modeCombination lap and shoulder belts in normal retract

How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt

WARNING: BELT AND RETRACTOR ASSEMBLY MUST BEREPLACED if the safety belt assembly “automatic lockingretractor” feature or any other safety belt functio

WARNING: Position the safety belt height adjusters so that thebelt rests across the middle of your shoulder. Failure to adjustthe safety belt properly

How to fasten the cinch tongue (Regular cab center seatingposition and Super Cab/Crew Cab rear center seating positions)1. Pull the combination lap an

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war

Door ajar (RTT): Displays whenthe ignition is in the on position andany door is open.Transmission Tow/Haul Feature(automatic transmission) (ifequipped

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra

WARNING: Do not sit on top of a buckled safety belt or insert alatchplate into the buckle to avoid the Belt-Minder威 chime. Todo so may adversely affec

• Step 3 must be completed within 60 seconds after the safety beltwarning light turns off.3. At a moderate speed, buckle then unbuckle the safety belt

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

WARNING: Never place your arm over the airbag module as adeploying airbag can result in serious arm fractures or otherinjuries.To properly position yo

Children and airbagsFor additional important safety information, read all information onsafety restraints in this guide.Children must always be proper

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

The diagnostic module monitors its own internal circuits and thesupplemental airbag electrical system wiring (including the impactsensors), the system

Passenger airbag ON/OFF switch (if equipped)WARNING: An airbagON/OFF switch (ifequipped) may be installed in thisvehicle. Before driving, alwayslook a

WARNING: An infant in a rear-facing seat faces a high risk ofserious or fatal injuries from a deploying passenger airbag. Rearfacing infant seats shou

Locks and Security 155Keys 155Locks 155Anti-theft system 168Seating and Safety Restraints 172Seating 172Safety restraints 181Airbags 193Child restrain

If your vehicle is equipped with a diesel engine, it has some uniquewarning lights; refer to Instrument Cluster in your 6.0 and 6.4 LiterPower Stroke

WARNING: If your vehicle has rear seats, always transportchildren who are 12 and younger in the rear seat. Always usesafety belts and child restraints

• the child has a medical condition which, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the dr

• the child has a medical condition that, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the dri

WARNING: All children are shaped differently. TheRecommendations for Safety Restraints are based on probablechild height, age and weight thresholds fr

• You are required by law to properly use safety seats for infants andtoddlers in the U.S. and Canada.• Many states and provinces require that small c

WARNING: Air bags can kill or injure a child in a child seat.NEVER place a rear-facing child seat in front of an active airbag. If you must use a forw

WARNING: Do not leave children, unreliable adults, or petsunattended in your vehicle.Transporting childrenAlways make sure your child is secured prope

When installing a child safety seat:• Review and follow the informationpresented in the Airbagsupplemental restraint system(SRS) section in this chapt

• Keep the buckle release button pointing up and away from the safetyseat, with the tongue between the child seat and the release button,to prevent ac

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

GAUGESSpeedometer: Indicates the current vehicle speed.Standard instrument clusterHarley-Davidson instrumentcluster2009 F-250/350/450/550 (f23)Owners

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out.6. All

9. Attach the tether strap (if thechild seat is equipped). Refer toAttaching child safety seats withtether straps later in this chapter.10. Before pla

WARNING: Airbags can kill or injure a child in a child seat. Ifyou must use a forward-facing child seat in the front seat, moveseat all the way back.W

4. Insert the belt tongue into theproper buckle for that seatingpositions until you hear a snap andfeel it latch. Make sure the tongue issecurely latc

7. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the

2. Place the child safety seat in the center seating position.3. Route the tongue and webbing through the child seat according to thechild seat manufa

The tether anchors in your vehicle may be straps on the seatback or ananchor bracket on the rear edge of the seat cushion or an anchor bracketmounted

Tether strap attachment1. Route the child safety seat tether strap over the back of the seat.For vehicles with adjustable head restraints, route the t

• Front seat (SuperCab)• Rear seats (Crew Cab)If the tether strap is clipped incorrectly, the child safety seat may not beretained properly in the eve

Tether strap attachment (rear SuperCab only)There are three loops of webbing just above the back of the rear seat(along the bottom edge of the rear wi

Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature, the needle will be inthe normal range (between “

3. Install the child safety seat tightlyusing the vehicle belts. Follow theinstructions in this chapter.4. Tighten the tether strapaccording to the ch

Booster seats position a child so that vehicle lap/shoulder safety belts fitbetter. They lift the child up so that the lap belt rests low across the h

Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

Move a child to a different seating location if the shoulder belt does notstay positioned on the shoulder during use.Follow all instructions provided

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

If equipped with a three button message center, press and releasethe message center INFO button until TRIP A or TRIP B appears in thedisplay. Press th

INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air

under-inflation of the tires, improper tires (load range, size, or type), orvehicle modifications such as lift-kits. In the event that your vehicleexp

Note: Some spare tires operate at a higher inflation pressure than theother tires. For T-type/mini-spare tires (see the Dissimilar sparetire/wheel inf

WARNING: Stay out of the trajectory (1) as indicated in theillustration.TIRE CAREInspecting your tiresPeriodically inspect the tire treads for uneven

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w

WARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the tires; spinning the tires can tear the tire andcause an explosion.

Tire rotationRotating your tires at the recommended interval (as indicated in thescheduled maintenance information that comes with your vehicle) willh

WARNING: If the tire label shows different tire pressures forthe front and rear tires and the vehicle is equipped with TPMS(tire pressure monitoring s

Engine oil pressure gauge:Indicates engine oil pressure. Theneedle should stay in the normaloperating range (between “L” and“H”). If the needle falls

INFORMATION CONTAINED ON THE TIRE SIDEWALLBoth U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the

7. H: Indicates the tire’s speed rating. The speed rating denotes thespeed at which a tire is designed to be driven for extended periods oftime under

10. Tire Ply Composition and Material Used: Indicates the number ofplies or the number of layers of rubber-coated fabric in the tire tread andsidewall

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti

When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.

Low TirePressureWarningLightPossible cause Customer Action RequiredFlashingWarningLightSpare tire in use Your temporary spare tire is in use.Repair th

Transmission fluid temperature gauge (automatic transmissiononly): If the gauge is in the:Normal area– the transmissionfluid is within the normal oper

TPMS reset procedure (if applicable)The TPMS reset tool is ONLY provided for vehicles with differentfront and rear tire pressures. The TPMS reset proc

Storing the TPMS reset toolYou should store the TPMS resettool in the provided pocket of theowner guide case; however, beforestoring it, you will need

and remain on for approximately five (5) seconds. If the light does notilluminate, the tool needs to be replaced.TPMS reset tips:• To reduce the chanc

4. Press and hold the brake pedalfor two (2) seconds, then release.5. Turn the ignition to off—DONOT remove the key.6. Cycle the ignition from off to

7. Train the TPMS sensors in the tires using the following TPMS resetsequence starting with the left front tire in the following clockwiseorder:1. Lef

10. Perform Steps 8 and 9 on the right front tire, right rear tire andfinally the left rear tire. Training is complete after the horn sounds forthe la

VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic

WARNING: The appropriate loading capacity of your vehicle canbe limited either by volume capacity (how much space isavailable) or by payload capacity

Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue loador king pin w

GVWR (Gross Vehicle Weight Rating) – is the maximum allowableweight of the fully loaded vehicle (including all options, equipment,passengers and cargo

AUDIO SYSTEMSAM/FM stereo system (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strong

safe control of towed vehicles and for trailers where the GCW of thetowing vehicle plus the trailer exceed the GVWR of the towing vehicle.The GCW must

4. The resulting figure equals the available amount of cargo and luggageload capacity. For example, if the “XXX” amount equals 1,400 lb. andthere will

The above calculations also assume that the loads are positioned in yourvehicle in a manner that does not overload the Front or the Rear GrossAxle Wei

the chart/table in the following text). This calculation will give you themaximum trailer weight possible for your vehicle.The weight of all additiona

Maximum GCWR - lb. (kg.)Engine Rear axleratioManualtransmissionAutomatictransmissionF–350 Dual Rear Wheel (DRW) Pick-up5.4L 4.10 17500 (7938) 18500 (8

Maximum GCWR - lb. (kg.)Engine Rear axleratioManualtransmissionAutomatictransmissionF–350 Dual Rear Wheel (DRW) Pick-up5.4L 4.10 17500 (7938) 18500 (8

Hitch ratingThe standard hitch has two ratings depending on mode of operation:• Weight carrying - requires a draw bar and hitch ball. The draw barsupp

2. Measure the height of a reference point on the front and rear bumpersat the center of the vehicle.3. Attach the trailer to the vehicle and adjust t

smooth and effective trailer braking by powering the trailer’s electricbrakes with a proportional output based on the towing vehicle’s brakepressure.W

• TRAILER DISCONNECTED: This message is displayed andaccompanied by a single chime, when a trailer connection wasdetermined and then a disconnection,

2. AUDIO: Press AUDIO repeatedlyto gain access to the followingsettings:TREB (Treble): Press AUDIO to reach the treble setting.Use/ / SEEK .BASS (Bass

5. In a traffic-free environment, tow the trailer on a dry, level surface ata speed of 20–25 mph (30–40 km/h) and squeeze the manual controllever comp

• Avoid towing in adverse weather conditions. The TBC does notprovide anti-lock control of the trailer wheels. Trailer wheels canlock-up on slippery s

type (All-Season or All-Terrain) or is from a different manufacturerother than the road tires on your vehicle, your spare tire is considered“temporary

• The load distribution within the trailer should be such that 10%–15%of the trailer weight is on the hitch. (15%–25% for fifth-wheel orgooseneck towi

Exceeding these limits may allow water to enter vehicle components:• causing internal damage to the components.• affecting driveability, emissions and

STARTINGPositions of the ignition1. Off— shuts off the engine and allaccessories/locks the steering wheeland allows key removal.2. Accessory— allows t

WARNING: If you smell exhaust fumes inside your vehicle, haveyour dealer inspect your vehicle immediately. Do not drive if yousmell exhaust fumes.Impo

If starting a vehicle with a manualtransmission:1. Make sure the parking brake isset.2. Push the clutch pedal to the floor.• Turn the key to 3 (on) wi

10 seconds or until the vehicle starts.Note: Cranking may be stopped at any time by turning the key to the offposition.3. After idling for a few secon

Prior to using the engine block heater, follow these recommendations forproper and safe operation:• For your safety, use an outdoor extension cord tha

AM/FM stereo single CD/satellite compatible sound system(if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident

How to Use the Engine Block HeaterEnsure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth.Depending on the type

ABS warning lampThe ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringsta

Pull the release lever to release theparking brake. To prevent the pedalfrom releasing too quickly, placeyour left foot on the service brakepedal, the

into four-wheel drive mode (if equipped), the traction control system willbe automatically disabled. Traction control operation will resume whenthe ve

• Do not fill the power steering pump reservoir above the MAX mark onthe reservoir, as this may result in leaks from the reservoir.If the power steeri

WARNING: Vehicles with a higher center of gravity such asutility vehicles and trucks handle differently than vehicles with alower center of gravity. U

2. Apply the brake. Use a tool (or asmall screwdriver) to pry out theaccess cover. Insert the tool into theaccess hole and slide the whiteoverride but

Understanding the shift positions of the 5–speed automatictransmissionThis vehicle is equipped with an adaptive Transmission Shift Strategy.Adaptive S

D (Overdrive) with Tow/Haul OFFD (Overdrive) with Tow/Haul OFF is the normal driving position for thebest fuel economy. The overdrive function allows

3 (Third)Transmission starts and operates in third gear only.Used for improved traction on slippery roads. Selecting 3 (Third)provides engine braking.

2. (Phone): If your vehicle isequipped with SYNC威, press toaccess SYNC PHONE features. Forfurther information, please refer to supplemental informatio

Using the clutchManual transmission vehicles have a starter interlock that preventscranking the engine unless the clutch pedal is fully depressed.To s

Shift according to the following shift speed charts:Upshifts when accelerating(recommended for best fuel economy)6-speed transmissionShift from: Trans

Parking your vehicle1. Apply the brake and shift into the neutral position.2. Fully apply the parking brake, then shift into 1 (First).3. Turn the ign

The RSS detects obstacles up to6 feet (2 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the fi

If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement

Objects in the red zone are closest to your vehicle and objects in thegreen zone are further away. Objects are getting closer to your vehicle asthey m

WARNING: Do not use the camera system with the tailgateopen.If the back end of the vehicle is hit or damaged, then check with yourauthorized dealer to

Manual Shift On Stop (MSOS) 4x4 system (if equipped)The 4WD system is engaged ordisengaged by rotating the controlfor both front wheel hub locks fromt

The 4WD system:• provides 4x4 High engagement and disengagement while the vehicle ismoving.• is operated by a rotary control located on the instrument

Using a Manual Shift On Stop (MSOS) 4x4 system (if equipped)Note: High shift efforts may be encountered when attempting toshift into and out of 4x4 mo

Customer Assistance 350Reporting safety defects (U.S. only) 356Reporting safety defects (Canada only) 356Cleaning 357Maintenance and Specifications 36

OK. The song will appear in the display for confirmation. Press OKagain and the display will read SONG DELETED. If you do not wantto delete the curren

Shifting from 4H (4x4 High) to 2H (2WD)Move the transfer case lever to 2H(2WD) at a stop or a vehicle speedbelow 5 mph (8 km/h).With the vehicle at co

5. If shifting to 2H (2WD) with the vehicle at a complete stop, disengagethe locking hubs (optional) by rotating the hub lock control from LOCKto FREE

Shifting from 2WD to 4x4 HIGHRotate the 4x4 control to the 4x4HIGH position at speeds up to55 mph (88 km/h).• The electronic shift 4x4system is design

3. Move the 4x4 control to the 4x4LOW position.4. Hold the shift conditions until the4x4 LOW indicator light illuminates.5. If the 4x4 LOW indicator l

How your vehicle differs from other vehiclesTruck and utility vehicles can differ from some other vehicles. Yourvehicle may be higher to allow it to t

sideways out of control or roll over. Remember, your safety and thesafety of others should be your primary concern.WARNING: Vehicles with a higher cen

WARNING: Vehicles with a higher center of gravity such asutility and four-wheel drive vehicles handle differently thanvehicles with a lower center of

can be found in the Maintenance and Specifications chapter. Youshould become thoroughly familiar with this information before youoperate your vehicle.

Driving through deep water may damage the transmission.Refer to Transmission temperature gauge in the Instrument Clusterchapter for transmission fluid

When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This r

SPEEDVOL (Speed sensitive volume, if equipped): Press MENU toreach the SPEEDVOL setting. Radio volume automatically gets louderwith increasing vehicle

Make sure you allow sufficient distance between you and other vehiclesfor stopping. Drive slower than usual and consider using one of the lowergears.

VEHICLE USED AS A STATIONARY POWER SOURCEAuxiliary equipment called power take-off, or PTO, is often added to theengine or transmission to operate uti

SNOWPLOWINGFord recommends that the Super Duty F-Series used for snow removalinclude the Snow Plow Package Option.Installing the snowplowWeight limits

• The snow plow prep package includes a unique powertrain controlstrategy which is required for diesel engine cooling during highwaydriving with the s

WARNING: Additional equipment such as snowplow equipmentmay effect the performance of the airbag sensors increasing therisk of injury. Please refer to

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co

FUEL PUMP SHUT-OFF SWITCHThis device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt.After an

FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth

Passenger compartment fuse panelThe fuse panel is located in thepassenger’s footwell. Remove thepanel cover to access the fuses.To remove the fuse pan

5. SEEK: In radio mode,press/ to access theprevious/next strong station.In CD/MP3 mode, press/to access the previous/next CD/MP3 track.In satellite ra

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Not used (spare)2 15A Not used (spare)3 15A Family Entertainmen

Fuse/RelayLocationFuse AmpRatingProtected Circuits11 10A Not used (spare)12 7.5A Power mirror switch, Driver power seat(Memory)13 5A Not used (spare)1

Fuse/RelayLocationFuse AmpRatingProtected Circuits33 10A Trailer tow brake controller, Trailer towbattery charge relay coil34 5A Not used (spare)35 10

WARNING: To reduce risk of electrical shock, always replacethe cover to the Power Distribution Box before reconnecting thebattery or refilling fluid r

Fuse/RelayLocationFuse AmpRatingProtected Circuits13 5A** Brake switch, Brake switch relay coil,SJB module, 4x4 module14 — Not used15 — Not used16 Rel

Fuse/RelayLocationFuse AmpRatingProtected Circuits36 10A** Gasoline engines: PowertrainControl Module (PCM) keep alivepower, Canister ventDiesel engin

Fuse/RelayLocationFuse AmpRatingProtected Circuits59 Relay PCM power bus (Fuses 68, 70, 72, 74,76) (Gasoline engines only)60 Diode One touch start (OT

CHANGING A FLAT TIREIf you get a flat tire while driving:• do not brake heavily.• gradually decrease the vehicle’s speed.• hold the steering wheel fir

2. Full-size dissimilar spare with label on wheel: This spare tire hasa label on the wheel that states: “THIS TIRE AND WHEEL FORTEMPORARY USE ONLY”Whe

The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following:• Handling, stability and braking performance• Comfort and

Note: In CD/MP3 mode, press SHUFFLE to play the tracks in randomorder. In MP3 folder mode, the system will randomly play all trackswithin the current

• Tow a trailer• Use snow chains on the end of the vehicle with the temporary sparetire• Use more than one temporary spare tire at a timeUse of a temp

Location of the spare tire and toolsIf your vehicle is equipped with a spare tire, jack and associated tools,refer to the following table for their lo

• Vehicles equipped with dualrear wheels, insert the lugwrench extension into the lugwrench to reach the lug nuts.2. Attach the spare tire lock key (A

WARNING: To prevent the vehicle from moving when youchange a tire, be sure the parking brake is set, then block (inboth directions) the wheel that is

6. Position the jack according to the following guides:• Front (4x2)• Front driver side (4x4)Note: Make sure the jack fits ontothe flat area on the ou

• RearNever use the front or reardifferential as a jacking point.WARNING: To lessen therisk of personal injury, donot put any part of your bodyunder t

10. Lower the wheel by turning the jack handle counterclockwise.Go to step 19.The following steps apply to F–350 Dual Rear Wheel (DRW) andF–450/F–550

• Front passenger side (4x4): F-350DRWNote: View shown from the rear ofthe vehicle to clearly identify thejack point.Note: Place the jack directly und

13. Insert the jack handle into thepump linkage.14. Use an up-and-down motionwith the jack handle to raise thewheel completely off the ground.Hydrauli

10–lug nut torque sequence19. Stow the flat tire. Refer to Stowing the flat/spare tire if the vehicleis equipped with a spare tire carrier.Note: Do no

In TEXT MODE sometimes the display requires additional text to bedisplayed. When the “>” indicator is active, press SEEKto view theadditional displ

If the ornament retention towers arealigned between the studs/lug nuts,the ornament is improperlyinstalled. This improper installationmay appear and s

4. Be sure to install all the clips on the nuts over the flanges so thatthere is an even gap all around and the retention clips are fully seated.Stowi

5. Repeat this tightness check procedure when servicing the spare tirepressure (every six months, per scheduled maintenance information),or at any tim

Inspect the wheel pilot hole prior toinstallation. If there is visiblecorrosion in wheel pilot hole,remove loose particles by wipingwith clean rag and

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level.5. Tu

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex

Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

Note: Towing an ESOF 4x4 vehicle with the front wheels on the groundwithout disengaging the front hubs may cause damage to the automatictransmission.N

Premium/Premium plus in-dash six CD/MP3/satellite compatiblesound system (if equipped)WARNING: Driving while distracted can result in loss of vehiclec

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

procedure outlined on the first page of the Customer Assistance section,you may be eligible to participate in the BBB AUTO LINE program.The BBB AUTO L

The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have

If you cannot find unleaded fuel or can only get fuel with an anti-knockindex lower than is recommended for your vehicle, contact a regionaloffice or

Obtaining a French owner’s guideFrench Owner’s Guides can be obtained from your authorized dealer orby writing to:Ford Motor Company of Canada, Limite

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent qu

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

Satellite radio is available only with a valid SIRIUS radiosubscription. Check with your authorized dealer for availability.2.(Phone): Press to access

• 6.8L V10 gasoline enginePLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32–A),available from your au

4. Remove the soaked cloth, and if it is not soiled badly, use this cloth toclean the area by using a rubbing motion for 60 seconds.5. Following this,

INTERIORFor fabric, carpets, cloth seats and safety belts:• Remove dust and loose dirt with a vacuum cleaner.• Remove light stains and soil with Motor

LEATHER SEATS FOR THE KING RANCH F-250 AND F-350 CREWCAB ONLY (IF EQUIPPED)Your vehicle is equipped with seating covered in premium, top-grainleather

ConditioningBottles of King Ranch Leather Conditioner are available at the KingRanch Saddle Shop. Visit the Web site at www.krsaddleshop.com,ortelepho

Motorcraft Dash and Vinyl Cleaner (ZC-38–A)Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A)Motorcraft Detail Wash (ZC-3–A)Motorcraft

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

2. Block the wheels.WARNING: To reduce the risk of vehicle damage and/orpersonal burn injuries, do not start your engine with the aircleaner removed a

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENTRefer to the 6.0 and 6.4 Liter Power Stroke Direct Injection TurboDiesel Owner’s Guide Supplement for

and the display will read SONG DELETED. If you do not want todelete the currently listed song, press/ to select eitherRETURN or CANCEL.Note: If there

6.8L V10 gasoline engine1. Windshield washer fluid reservoir2. Battery3. Transmission fluid dipstick (automatic transmission)4. Engine oil filler cap5

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the locktab to release the bla

• 5.4L/6.8L gasoline engines only;for diesel engine information,refer to the 6.0 and 6.4 LiterDirect Injection Turbo DieselOwner’s Guide Supplement.6.

4. Install the dipstick and ensure it is fully seated.5. Fully install the engine oil filler cap by turning the filler cap clockwise1/4 of a turn unti

It is recommended you use the appropriate Motorcraft oil filter oranother with equivalent performance for your engine application.BATTERYWARNING: This

WARNING: When lifting a plastic-cased battery, excessivepressure on the end walls could cause acid to flow through thevent caps, resulting in personal

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO

• Add Motorcraft Premium Gold Engine Coolant or equivalentmeeting Ford specification WSS-M97B51-A1. Refer toMaintenance product specifications and cap

To view the station name or type: When the desired category appearsin the display, press TEXT/SCAN to toggle between displaying the stationtype (COUNT

WARNING: To reduce the risk of personal injury, make sure theengine is cool before unscrewing the coolant pressure relief cap.The cooling system is un

Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant since a Ford-approved recycling process is not yet avai

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i

When fail-safe mode is activatedYou have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be ab

WARNING: If you do not use the proper fuel filler cap,excessive vacuum in the fuel tank may damage the fuel systemor cause the fuel cap to disengage i

• Be particularly careful if you are taking “Antabuse” or other forms ofdisulfiram for the treatment of alcoholism. Breathing gasoline vapors,or skin

Fuel filler capWhen fueling your vehicle:1. Turn the engine off.2. Carefully turn the filler cap counterclockwise until it spins off.3. Pull to remove

Choosing the right fuelUse only UNLEADED fuel or UNLEADED fuel blended with a maximumof 10% ethanol. Do not use fuel ethanol (E85), diesel, methanol,

Many of the world’s automakers approved the World-Wide Fuel Charterthat recommends gasoline specifications to provide improvedperformance and emission

The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fu

COMPRESS (Compression): Available only in CD/MP3 mode. PressMENU until COMPRESS ON/OFF appears in the display.Use/ / SEEK, SEEK to toggle ON/OFF. When

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fuelecon

Maintenance• Keep tires properly inflated and use only recommended size.• Operating a vehicle with the wheels out of alignment will reduce fueleconomy

EMISSION CONTROL SYSTEMYour vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to co

Do not make any unauthorized changes to your vehicle or engine. Bylaw, vehicle owners and anyone who manufactures, repairs, services,sells, leases, tr

Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect

POWER STEERING FLUIDCheck the power steering fluid. Refer to scheduled maintenanceinformation. If adding fluid is necessary, use only MERCON威 ATF.• Ga

BRAKE FLUID• Vacuum boost system• Hydroboost systemThe fluid level will drop slowly as the brakes wear, and will rise when thebrake components are rep

CLUTCH FLUID (IF EQUIPPED)Check the fluid level. Refer to scheduled maintenance information forthe service interval schedules.During normal operation,

1. Drive the vehicle 20 miles (30 km) or until it reaches normal operatingtemperature.2. Park the vehicle on a level surface and engage the parking br

High fluid levelFluid levels above the safe rangemay result in transmission failure.An overfill condition of transmissionfluid may cause shift and/ore

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

OK: Use in various menu selections.If your vehicle is equipped with a Family Entertainment System (FES)please refer to the Family entertainment DVD sy

Checking and adding manual transmission fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Fluid leve

TRANSFER CASE FLUID (IF EQUIPPED)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough fluid throughthe fil

AIR FILTERRefer to the scheduled maintenance information for the appropriateintervals for changing the air filter element.When changing the air filter

2. Release three retainer clamps.3. Pull air filter cover toward passenger side of vehicle and up to releasethe tabs. Lift air filter element up and o

MOTORCRAFT PART NUMBERSComponent 5.4L V8/6.8L V10 enginesAir filter element FA-1883Fuel filter FG-1083Oil filter FL-820-SPCV valve1Battery (Standard)

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationFront axle 5.8 pints (2.8L)Motorcraft

Item Capacity Ford part nameFord part number /Ford specificationEngine coolant(6.8L V10 engine)226.7 quarts(25.3L)Motorcraft PremiumGold Engine Coolan

Item Capacity Ford part nameFord part number /Ford specificationHinges, latches, strikerplates, fuel filler doorhinge and seat tracks— Multi-Purpose G

Item Capacity Ford part nameFord part number /Ford specificationAutomatic transmissionfluid (5R110)317.5 quarts(16.6L)5(includesremote filterelement c

ENGINE DATAEngine 5.4L V8 engine 6.8L V10 engineCubic inches 330 415Required fuel 87 octane 87 octaneFiring order 1-3-7-2-6-5-4-8 1-6-5-10-2-7-3-8-4-9

13. TEXT/SCAN: In radio andCD/MP3 mode, press and hold for2 seconds to activate mode to heara brief sampling of radio stations or CD tracks. Press aga

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

LifestyleAsh cup / smoker’s packageBedliners and bedmatsCargo organization and managementTowing mirrorsTrailer hitches, wiring harnesses and accessori

AAccessory delay ...110Air cleaner filter ...402, 404Air conditioning ...84Airbag supplemental

safety belts ...363washing ...357waxing ...358wheels ...

recommendations ...374refill capacities ...405Event data recording ...7Exhaust fumes ...

Inspection/maintenance (I/M)testing ...394Instrument panelcleaning ...361–362cluster ...

Pedals (see Power adjustablefoot pedals) ...115Power adjustable foot pedals ...115Power distribution box(see Fuses) ...

Steering wheelcontrols ...118tilting ...104SYNC威 ...

If you do not choose a slot within five seconds, the system will choosefor you. Once loaded, the first track will begin to play.To auto load up to 6 d

Your vehicle may be equipped withan Auxiliary Input Jack (AIJ). TheAuxiliary Input Jack, located on theinstrument panel below the powerpoint, provides

Troubleshooting:1. Do not connect the audio input jack to a line level output. Line leveloutputs are intended for connection to a home stereo and are

Your vehicle may be equipped with aUSB port located on the instrumentpanel. This feature allows you toplug in media playing devices,memory sticks, and

CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

Radio Display Condition Action RequiredACQUIRING Radio requiresmore than twoseconds toproduce audiofor the selectedchannel.No action required. This me

Radio Display Condition Action RequiredNO SIGNAL Loss of signalfrom the SIRIUSsatellite orSIRIUS tower tothe vehicleantenna.You are in a location that

To play a DVD in the DVD system:The DVD system can play DVD-Video, DVD-R, DVD-R/W discs as well asaudio CDs and video CDs. To ensure proper disc opera

2. Insert a CD into the system,label-sideuptoturnontheDVDsystem. It will load andautomatically begin to play. If thereis already a CD in the system, p

2. Press the power button to turnthe DVD system on. The indicatorlight next to the power button willilluminate.3. Connect an auxiliary audio/videosour

Note: Channel A can access any possible media source (AM, FM1, FM2,SAT (if equipped), CD, DVD, AUX). Channel B can only access DVD andAUX sources.Note

DVD player controls1. Headphone control A/B: Pressto select either the A or Bheadphone source. Then pressMEDIA to select the desired playingmedia for

4. (Fast forward): Press andrelease for the next chapter ortrack. Press and hold to forwardsearch a DVD, Video CD, or FES CD in DVD/CD mode.5./ (Play/

11. / (Headphones/Speakers): Press once for Dual Play(Headphone mode- the rear speakers are muted) and press again forSingle Play (same media playing

Remote controlUnless otherwise stated, all operations can be carried out with theremote control. Always point the remote control directly at the playe

PERCHLORATE MATERIALCertain components of this vehicle such as airbag modules, seat beltpretensioners, and button cell batteries may contain Perchlora

7. VOL (Volume): When in Single Play, press to increase ( )ordecrease () the volume over all speakers. When in Dual Play, press toincrease () or decre

21. LANGUAGE (DVD dependent): Press to select the desiredlanguage.22. ENTER: Press to select the highlighted menu option.23. ILLUMINATION: Press to il

HeadphonesWireless headphonesWARNING: The driver should never use the headphones whiledriving the vehicle. Using headphones may prevent the driverfrom

To install the batteries, remove the screw at the bottom of the cover.Then, lightly press down on top and slide the cover off.When replacing the batte

To operate the headphones:• Press POWER on the ear piece to turn on the headphones. A redindicator light will illuminate indicating the headphones are

Wired headphonesWARNING: Do not leave children unattended in the vehicle anddo not let children operate the system while unsupervised. Ifwired headpho

Single Play: Single play consists of all occupants in the vehicle listeningto the same playing media over the front and rear speakers. When theDVD sys

Operation with an aftermarket audio system(Headphone only mode)When the Family Entertainment System (FES) detects that the originalradio supplied by F

This is disc dependent — someDVD discs may have more viewingangles to select from. Once youhave made your selection, pressENTER to confirm. The system

Once you have made your selection,press ENTER to confirm. Thesystem default is English.SubtitlesSelect SUBTITLES to turn thesubtitle option on or off.

Service Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This pote

COMP (Compression): Compression brings soft and loud CD passagestogether for a more consistent listening level when in CD mode. Press toturn the featu

• Bit rate — The player supports bit rates from 32–320 kbps, as well asvariable bit rate MP3 files, but lower bit rates will have a noticeableeffect o

The FES DVD system is designed to play commercially pressed12 cm (4.75 in) audio compact discs and digital versatile discs(DVD), DVD-R and R/W discs o

Slow play1. With a DVD playing, press pause.2. Press and hold the reverse oradvance button to enter into slowplay mode. Once in slow play mode,press a

3. Red: right channel audio input4. Black: wired headphone jack (not included)The B headphone jack (5) is locatedon the right side of the DVD system.P

LOCKED (disabled). To change the level of control, press the memorypreset controls 3 and 5 simultaneously on the front audio controls. Thecontrol leve

MP3: Supply of this product only conveys a license for private,non-commercial use and does not convey a license nor imply any right touse this product

Do not expose the liquid crystal display (LCD) flip-down screento direct sunlight or intensive ultraviolet rays for extensiveperiods of time. Ultravio

Care and service of the DVD playerEnvironmental extremesDVD players which are subjected to harsh environmental conditions maybe damaged or perform at

Cleaning DVD and CD discsInspect all discs for contamination before playing. If necessary, cleandiscs only with an approved DVD and CD cleaner and wip

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access e

HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe

3. Set the fan speed to the highest setting.4. Direct the outer instrument panel vents towards the side windows.To increase airflow to the outer instr

1. Fan speed adjustment: Controls the volume of air circulated in thevehicle.2. Temperature selection: Controls the temperature of the airflow inthe v

Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEMS(IF EQUIPPED)• DATC• DATC with heated mirrors2009 F-250/350/450/550 (f23)Owners Guide, 3rd PrintingUS

• DATC with heated seats and heated mirrorsTemperature conversion: To switch between Fahrenheit and Celsius,refer to Units (English/Metric) under eith

4. Recirculation control: Press to activate/deactivate airrecirculation in cabin. Recirculated air may reduce the amount of time tocool down the inter

Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up

In (panel) or (panel/floor) modes:1. Move temperature control to full cold.2. Select A/C and(recirculated air). Use recirculated air with A/C toprovid

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola

Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.WARNING: Please read the section Airbag Supple

Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the on position,• the head

PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicableilluminated switches in the vehicleduring headlamp and parkl

To adjust the headlamps:1. Park your vehicle on a levelsurface about 25 feet (7.6 meters)away from a vertical plain surface(3). Check your headlamp al

5. Locate the vertical adjuster (2)for each headlamp. Adjust the aimby turning the adjuster controleither clockwise (to adjust up) orcounterclockwise

• (4) Horizontal reference line2. Measure the height from thecenter of your headlamp (indicatedby a 3.0 mm circle on the lens) tothe ground and mark a

MAP LAMPS (IF EQUIPPED)The dome lamp turns on when:• any door is opened,• the instrument panel dimmerswitch is rotated up until thecourtesy lamps come

Replacing exterior bulbsCheck the operation of all the bulbs frequently.Function Numberof bulbsTrade numberHeadlamps (aerodynamic) 2 H13/9008Headlamps

Replacing headlamp bulbs (aerodynamic)1. Make sure that the headlamps are off and open the hood.2. Remove the four bolts from thetop, side and bottom

Replacing park/turn and sidemarker lamp bulbs (aerodynamic)1. Make sure that the headlamps are off and open the hood.2. Remove the four bolts from the

Replacing headlamp bulbs (sealed beam)1. Make sure that the headlamps are off and open the hood.2. Remove the three screws and onebolt from the top an