Introduction 4Instrument Cluster 14Warning lights and chimes 14Gauges 21Entertainment Systems 26AM/FM stereo 26AM/FM stereo with CD 28AM/FM stereo wit
Using your vehicle with a snowplowFor more information and guidelines for using your vehicle with asnowplow, refer to the Driving chapter.Using your v
4. Remove the bulb assembly,sidemarker or park/turn by turningit counterclockwise. (Top view ofassembly shown.)5. Pull the old bulb out from thesocket
Replacing cargo lamp and high-mount brakelamp bulbs1. Make sure the headlamps are off.2. Remove the two screws and lampassembly from vehicle as wiring
Replacing license plate lamp bulbsThe license plate bulbs are locatedbehind the rear bumper. To changethe license plate lamp bulbs:1. Reach behind the
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT STEERING WHEEL1. Pull and hold the steering wheelrelease control toward you.2. Move the steering up or downuntil you find the desired location.3.
ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamp.OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehic
CENTER CONSOLE (IF EQUIPPED)Your vehicle may be equipped with a variety of console features. Theseinclude:• Utility compartment withcassette/CD holder
Under-seat storageFlip the rear seat cushion up toaccess the rear under-seat storagearea. See Seating in the Seatingand safety restraints chapter form
To prevent the fuse from being blown, do not use the power point(s)over the vehicle capacity of 12 VDC/180W. If the power point or cigarlighter socket
Press and pull the window switchesto open and close windows.• Push down (to the first detent)and hold the switch to open.• Pull up (to the first deten
Using your vehicle as a stationary power source (PTO)Refer to the Driving chapter for more information and guidelines foroperating a vehicle equipped
Power rear slider window (if equipped)WARNING: Do not leave children unattended in the vehicle anddo not let children play with the power windows. The
Without microphoneWith microphoneThe mirror will automatically return to the normal state whenever thevehicle is placed in R (Reverse) to ensure a bri
Heated outside mirrors (if equipped)The main mirror glass and lowerconvex spotter mirror are heated toremove ice, mist and fog. To activatethe heated
Powerfold mirror positions, from left to right: Position 1, Position 2,Position 3The powerfold mirrors may be folded forward/rearward manually to anyo
Telescoping mirrors (if equipped)The telescoping feature allows themirror to extend approximately2.75 inches (70 mm). This feature isespecially useful
Mirror mounted side turn signal indicator (if equipped)When the vehicle turn signals areactivated, the outer portion of themirror housing will blink a
The accelerator and brake pedal positions are saved when doing amemory set function and can be recalled along with the vehiclepersonality features whe
• If the vehicle speed increases above the set speed on a downhill, youmay want to apply the brakes to reduce the speed.• If the vehicle speed decreas
Reducing speed while using speed controlThere are two ways to reduce a setspeed:• Press and hold the SET - controluntil you get to the desiredspeed, t
Audio control featuresPress MEDIA to select:• AM, FM1, FM2• CD (if equipped)• DVD (if equipped)• SAT1, SAT2 or SAT3 (SatelliteRadio mode, if equipped)
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
Navigation system hands freecontrol features (if equipped)Press and hold VOICE briefly untilthe voiceicon appears on theNavigation display to use the
For further information on the Navigation system/SYNC system, refer tothe Navigation System and SYNC supplements.UPFITTER CONTROLS (IF EQUIPPED)Your v
There will also be one power leadfor each switch found as a blunt-cutand sealed wire located below theinstrument panel and to the left ofthe steering
To open the moon roof: The moon roof is equipped with a one-touchopen feature. Press and release thecontrol. The moon roof will opento the “comfort” p
Do not use the HomeLink威 Wireless Control System with any garagedoor opener that lacks safety stop and reverse features as required byU.S. federal saf
• If the indicator light stays on constantly, programming is completeand your device should activate when the HomeLink威 button is pressedand released.
• Continue to press and hold the HomeLink威 button (note Step 2 in theProgramming section) while you press and release — every twoseconds (“cycle”) you
2. The indicator light will begin to flash after 20 seconds. Withoutreleasing the HomeLink威 button, follow Step 1 in the Programmingsection.For questi
Odometer/Trip odometerRefer to Gauges in the Instrument Cluster chapter.Engine hour meter (if equipped)Refer to Gauges in the Instrument Cluster chapt
2. Record the highway fuel economy for future reference.It is important to press the SELECT/RESET button (press and hold fortwo seconds in order to re
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
2. Press and hold theSELECT/RESET button for twoseconds and release. Oil life is set to100% and “OIL LIFE SET TO 100%”is displayed.Note: To change oil
message or a warning message for two seconds. Pressing theSELECT/RESET button cycles the message center through each of thesystems being monitored.The
3. Once “OIL LIFE SET TO XXX%” is displayed, release and press theRESET control switch to change the Oil Life Start Value. Each releaseand press will
Warning display StatusLow tire pressure (if equipped) Warning can be cleared by pressingthe RESET button. Warning canreappear if the condition is stil
DRIVER DOOR AJAR — Displayed when the driver’s door is notcompletely closed.PASSENGER DOOR AJAR — Displayed when the passenger’s door isnot completely
CHECK AIR FILTER (Diesel engine only) — Refer to InstrumentCluster in your 6.0 and 6.4 Liter Power Stroke Direct Injection TurboDiesel Owner’s Guide S
DRIVE TO CLEAN EXHAUST FILTER (Diesel engine only) —Displayed when the engine control module detects the Diesel ParticulateFilter (DPF) is full of par
OPTIONAL MESSAGE CENTER (IF EQUIPPED)With the ignition in the on position,the message center, located on yourinstrument cluster, displaysimportant veh
Info menuThis control displays the followingitems:• Trip odometer A or B• Engine hour meter/odometer (ifequipped)• Distance to empty• Average fuel eco
Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in miles/gallon orliters/100 km.If you calculate
WARNING LIGHTS AND CHIMESVehicles equipped with a manual transmissionVehicles equipped with an automatic transmission2009 F-250/350/450/550 (f23)Owner
Setup menuPress this control for the followingdisplays:• System check• Units (English/Metric)• Autolamp timer presets (ifequipped)• Autolock On/Off (i
5. AIR FILTER (Diesel engine only)6. DOOR AJAR7. BRAKE SYSTEM8. TBC GAIN = XX.XNO TRAILER (if equipped and no trailer connected)9. TBC GAIN = XX.XOUTP
Units (English/Metric)1. Select this function from theSETUP menu for the current unitsto be displayed.2. Press the RESET button tochange from English
Most geographic areas (zones) have a magnetic north compass point thatvaries slightly from the northerly direction on maps. This variation is fourdegr
8. Slowly drive the vehicle in acircle (less than 3 mph [5 km/h])until the CIRCLE SLOWLY TOCALIBRATE display changes toCALIBRATION COMPLETED. It willt
This acts as a reminder that these warning conditions still exist withinthe vehicle.Warning display StatusPark brake engaged Warning returns after 10
Warning display StatusCheck air filter (diesel engineonly)Drain water separator (dieselengine only)Stop safely now (diesel engineonly)Engine warming p
REAR RIGHT DOOR AJAR — Displayed when the rear right door isnot completely closed.FUEL LEVEL LOW — Displayed as an early reminder of a low fuelconditi
DRAIN WATER SEPARATOR (Diesel engine only) — Displayedwhen the water separator has reached a predetermined capacity andneeds to be drained. Refer to y
DRIVE TO CLEAN EXHAUST FILTER (Diesel engine only) —Displayed when the engine control module detects the Diesel ParticulateFilter (DPF) is full of par
Harley-Davidson vehiclesWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A war
TAILGATE LOCK (IF EQUIPPED)Your vehicle may be equipped with atailgate lock designed to helpprevent theft of the tailgate.• Insert ignition key and tu
4. Lower the tailgate.5. Using a screwdriver, gently prythe spring clip (on each connector)past the head of the support screw.Disconnect cable.6. Disc
• Always use grab handle when stepping up and down.• Step not intended for bare-footed use.• Keep step clean from contamination before use (e.g. snow,
2. Open the latches to release thepanels.3. Rotate the panels toward thetailgate.Repeat Steps 1–3 for the other side of the bed extender.4. Connect th
5. Ensure the latch rod is insertedinto the tailgate hole and the lockingpins on both sides are engaged intotheir holes in the pick-up box.6. Reverse
KEYSThe key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency.If
Autolock feature (if equipped)The autolock feature will lock all the doors when:• all the doors are closed,• the ignition is in the on position,• you
5. Turn the ignition back to the on position. The horn will chirp one timeto confirm programming mode has been entered and is active.6. To enable/disa
• using a keypad procedure (if equipped)Note: The autounlock feature can be activated/deactivatedindependently of the autolock feature.Power door lock
CHILDPROOF DOOR LOCKS (IF EQUIPPED)• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the ou
chapter. If the light is blinking, engine misfire is occurring which coulddamage your catalytic converter. Drive in a moderate fashion (avoidheavy acc
Your vehicle is equipped with a remote entry system which allows you to:• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta
2. Press and release again within three seconds to confirm that allthe doors are closed and locked. Note: The doors will lock again, thehorn will chir
Deactivating the memory featureTo deactivate this feature:1. Press and hold either memory 1 button or memory 2 button for fiveseconds. A tone will be
Replacing lost remote entry transmittersIf you would like to have your remote entry transmitter reprogrammedbecause you lost one, or would like to buy
Perimeter lamps illuminated entryWith the Remote Keyless Entry system, the following items willilluminate when thecontrol on the transmitter is presse
Note: The horn will chirp once to indicate the perimeter lighting featurehas been deactivated. The horn will chirp once and honk once (one shortand on
Programming a personal entry code and keypad association tomemory seats, mirrors and pedalsTo create your own personal entry code:1. Enter the factory
The anti-scan feature will turn off after:• one minute of keypad inactivity.• pressing thecontrol on the remote entry transmitter.• the ignition is tu
Anti-theft indicatorThe anti-theft indicator is located in the instrument cluster.Vehicles equipped with theSecuriLock™ Passive Anti-theftsystem behav
Programming spare keysA maximum of eight keys can be coded to your vehicle. OnlySecuriLock™ keys can be used. To program a coded key yourself, youwill
Airbag readiness: If this light failsto illuminate when ignition is turnedto on, continues to flash or remainson, have the system servicedimmediately
If not successful, the new coded key(s) will not start the vehicle’s engineand the theft indicator will flash on and off and you may repeat Steps 1thr
SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o
Full bench seat (if equipped)• Lift the release bar to move theseat forward or backward. Ensurethat the seat is relatched intoplace.• Pull up on the l
40/20/40 front seat armrest and console (if equipped)To release the armrest, pull forwardon the strap and pull the armrestdown.To gain access to the s
Captain’s chair (if equipped)• Lift the bar to move the seatforward or rearward. Make surethat the seat is relatched intoplace.• To recline the seatba
Press front to raise or lower thefront portion of the seat cushion.Press rear to raise or lower the rearportion of the seat cushion.Press the control
Heated seats (if equipped)The heated seat control is located on the climate control panel.WARNING: Persons who are unable to feel pain to the skinbeca
To recall a memory position:• Press and release either memory 1 button or memory 2 button.A position can be recalled:• in any gearshift position if th
Push control to lower head restraint.WARNING: To minimize the risk of neck injury in the event of acrash, the driver and passenger occupants should no
To flip the seat cushion up, pullup on the lever located on the sideof the seat cushion to rotate thecushion up until it locks into avertical storage
transmission problem has been detected and shifting may be restricted.If the light remains on, have the system serviced immediately by yourauthorized
To gain access to the 60/40 loadfloor, store the cushion in theupright locked position. Pull up onthe straps located at the sides of theload floor, an
WARNING: Each seating position in your vehicle has a specificsafety belt assembly which is made up of one buckle and onetongue that are designed to be
2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.Vehicle sensitive modeCombination lap and shoulder belts in normal retract
How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt
WARNING: BELT AND RETRACTOR ASSEMBLY MUST BEREPLACED if the safety belt assembly “automatic lockingretractor” feature or any other safety belt functio
WARNING: Position the safety belt height adjusters so that thebelt rests across the middle of your shoulder. Failure to adjustthe safety belt properly
How to fasten the cinch tongue (Regular cab center seatingposition and Super Cab/Crew Cab rear center seating positions)1. Pull the combination lap an
Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignition switchis turned to the on position...The safety belt wa
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra
Transmission Tow/Haul Feature(automatic transmission)(if equipped): The Tow Haul lightremains illuminated as long as theTow/Haul feature is activated.
Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate
WARNING: While the design allows you to deactivate yourBelt-Minder威, this system is designed to improve your chances ofbeing safely belted and survivi
Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label.
WARNING: When possible, all children 12 years old and undershould be properly restrained in a rear seating position.WARNING: The National Highway Traf
WARNING: Removing the blocker beam without installing snowplow attachment hardware may effect airbag deployment in acrash. Do not operate the truck un
How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustainssufficient longitudinal decelera
WARNING: If the air bag has deployed, the air bag will notfunction again and must be replaced immediately. If the airbag is not replaced, the unrepair
The S.O.S. Post Crash Alert can be turned off when any one of thefollowing actions are taken by the driver or any other person:• pressing the hazard c
WARNING: If the light fails to illuminate when the passenger airbag switch is in the OFF position and the ignition switch is inON, have the passenger
WARNING: The safety belts for the driver and right frontpassenger seating positions have been specifically designed tofunction together with the airba
Locks and Security 155Keys 155Locks 155Anti-theft system 167Seating and Safety Restraints 171Seating 171Safety restraints 180Airbags 192Child restrain
Diesel warning lights:• Glow plug pre-heat• Waterinfuel• Low oil pressureKey-in-ignition warning chime: Sounds when the key is left in theignition in
• the vehicle has a rear seat too small to accommodate a rear-facinginfant seat; or• the infant has a medical condition which, according to the infant
• my vehicle has no rear seat;• the rear seat in my vehicle cannot accommodate a rear-facing infantseat; or• the infant has a medical condition which,
Important child restraint precautionsWARNING: Always make sure your child is secured properly ina device that is appropriate for their height, age and
Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeSmallchildrenChildren who have outgrown o
Recommendations for attaching child safety restraints for childrenNote: This vehicle is not equipped with LATCH lower anchors.RestraintTypeChildWeight
WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli
restrained properly, then restrain the child in the child safety seat orwith the belt-positioning booster. Remember that child seats andbelt-positioni
When installing a child safety seat with combination lap/shoulder belts:• Use the correct safety belt buckle for that seating position.• Insert the be
WARNING: Rear facing child seats should NEVER be placed inthe front seats unless the passenger airbag switch is turned off.2. Pull down on the shoulde
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out.6. All
GAUGESSpeedometer: Indicates the current vehicle speed.Standard instrument clusterHarley-Davidson instrumentcluster2009 F-250/350/450/550 (f23)Owners
9. Attach the tether strap (if thechild seat is equipped). Refer toAttaching child safety seats withtether straps later in this chapter.10. Before pla
WARNING: Airbags can kill or injure a child in a child seat. Ifyou must use a forward-facing child seat in the front seat, moveseat all the way back.W
4. Insert the belt tongue into theproper buckle for that seatingpositions until you hear a snap andfeel it latch. Make sure the tongue issecurely latc
7. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the
2. Place the child safety seat in the center seating position.3. Route the tongue and webbing through the child seat according to thechild seat manufa
The tether anchors in your vehicle may be straps on the seatback or ananchor bracket on the rear edge of the seat cushion or an anchor bracketmounted
Tether strap attachment1. Route the child safety seat tether strap over the back of the seat.For vehicles with adjustable head restraints, route the t
• Front seat (SuperCab)• Rear seats (Crew Cab)If the tether strap is clipped incorrectly, the child safety seat may not beretained properly in the eve
Many tether straps cannot be tightened if the tether strap is hooked tothe loop directly behind the child seat. To provide a tight tether strap:1. Rou
Child booster seatsThe belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child
Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature, the needle will be inthe normal range (between “
When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the
Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary
• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and
TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen
TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary
INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air
Standard instrument clusterHarley-Davidson instrumentclusterEngine hour meter(if equipped): Registers theaccumulated time the engine hasbeen running.
The cold inflation pressure should never be set lower than therecommended pressure on the Safety Compliance Certification Label orTire Label.When weat
Tire inflation informationAll tires with Steel Carcass Plies (if equipped):This type of tire utilizes steel cords in the sidewalls. As such, theycanno
WARNING: Stay out of the trajectory (1) as indicated in theillustration.TIRE CAREInspecting your tiresPeriodically inspect the tire treads for uneven
Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w
• Do not run over curbs or hit the tire against a curb when parkingWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can b
• DRW – Six tire rotationIf your vehicle is equipped with dualrear wheels it is recommended thatthe front and rear tires (in pairs) berotated only sid
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the on position). The fuelgauge may vary slightly whe
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe
The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw
Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti
Low TirePressureWarning LightPossiblecauseCustomer Action RequiredSolid WarningLightTire(s)under-inflated1. Check your tire pressure toensure tires ar
Low TirePressureWarning LightPossiblecauseCustomer Action RequiredFlashingWarning LightSpare tire inuseYour temporary spare tire is in use.Repair the
TPMS reset procedure (if applicable)The TPMS reset tool is ONLY provided for vehicles with differentfront and rear tire pressures. The TPMS reset proc
Yellow area (warning) — thetransmission fluid is higher thannormal operating temperature. Thiscan be caused by special operationconditions (i.e. snowp
Storing the TPMS reset toolYou should store the TPMS resettool in the provided pocket of theowner guide case; however, beforestoring it, you will need
and remain on for approximately five (5) seconds. If the light does notilluminate, the tool needs to be replaced.TPMS reset tips:• To reduce the chanc
4. Press and hold the brake pedalfor two (2) seconds, then release.5. Turn the ignition to off—DONOT remove the key.6. Cycle the ignition from off to
7. Train the TPMS sensors in the tires using the following TPMS resetsequence starting with the left front tire in the following clockwiseorder:1. Lef
10. Perform Steps 8 and 9 on the right front tire, right rear tire andfinally the left rear tire. Training is complete after the horn sounds forthe la
VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or performance, e
AUDIO SYSTEMSAM/FM stereo system (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strong
WARNING: Do not use replacement tires with lower loadcarrying capacities than the original tires because they maylower the vehicle’s GVWR and GAWR lim
• A final example for your vehicle with 1,400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the
Your vehicle may tow a Conventional/Class IV trailer or fifth wheel trailerprovided the maximum trailer weight is less than or equal to themaximum tra
Maximum GCWR - lb. (kg.)Engine Rear axleratioManualtransmissionAutomatictransmissionF–250 Pick-up5.4L 3.73 15000 (6804) 16000 (7257)4.10 17000 (7711)
HitchesWARNING: ON PICK-UP TRUCKS, the trailer hitch provided onthis vehicle enhances collision protection for the fuel system. DONOT REMOVE!Do not mo
WARNING: Towing trailers beyond the maximum tongue weightexceeds the limit of the towing system and could result invehicle structural damage, loss of
WARNING: If you own a trailer with a hydraulic brake system,do not connect the trailer’s hydraulic brake system directly toyour vehicle’s brake system
• TBC GAIN = XX.X NO TRAILER: The instrument cluster messagecenter will display the current gain setting during a given ignitioncycle and when adjusti
Note: This should only be performed in a traffic free environment atspeeds of approximately 20–25 mph (30–40 km/h).1. Make sure the trailer brakes are
Note: Your TBC can be diagnosed by your authorized dealer todetermine exactly which trailer fault has occurred; however, if the faultis with the trail
2. AUDIO: Press AUDIO repeatedlyto gain access to the followingsettings:TREB (Treble): Press AUDIO to reach the treble setting.Use/ / SEEK .BASS (Bass
Driving while you towWhen towing a trailer:• Do not drive faster than 70 mph (113 km/h) during the first 500 miles(800 km) of trailer towing and don’t
• If you will be towing a trailer frequently in hot weather, hillyconditions, at GCWR, or any combination of these factors, considerrefilling your rea
Tires• All trailer tires should be of the same size, and construction.• Select tires that meet the trailer loading requirements.• Always check tow veh
Transmission DrivetrainconfigurationRequirements forneutral towingManual 4x4 with manual-shifttransfer caseTransmission in (N)Neutral; Transfer casein
STARTINGPositions of the ignition1. Off— shuts off the engine and allaccessories/locks the steering wheeland allows key removal.2. Accessory— allows t
WARNING: If you smell exhaust fumes inside your vehicle, haveyour dealer inspect your vehicle immediately. Do not drive if yousmell exhaust fumes.Impo
If starting a vehicle with a manualtransmission:1.Make sure the parking brake is set.2. Push the clutch pedal to the floor.• Turn the key to 3 (on) wi
3. After idling for a few seconds, apply the brake, shift into gear anddrive.Note: If the engine does not start on the first try, turn the key to the
Prior to using the engine block heater, follow these recommendations forproper and safe operation:• For your safety, use an outdoor extension cord tha
How to Use the Engine Block HeaterEnsure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth.Depending on the type
7. CLK (Clock): Press CLK totoggle between the clock and radiofrequency.AM/FM stereo single CD/satellite compatible sound system(if equipped)WARNING:
ABS warning lampThe ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringsta
Pull the release lever to release theparking brake. To prevent the pedalfrom releasing too quickly, placeyour left foot on the service brakepedal, the
into four-wheel drive mode (if equipped), the traction control system willbe automatically disabled. Traction control operation will resume whenthe ve
• Do not fill the power steering pump reservoir above the MAX mark onthe reservoir, as this may result in leaks from the reservoir.If the power steeri
WARNING: Vehicles with a higher center of gravity such asutility vehicles and trucks handle differently than vehicles with alower center of gravity. U
2. Apply the brake. Use a tool (or asmall screwdriver) to pry out theaccess cover. Insert the tool into theaccess hole and slide the whiteoverride but
Understanding the shift positions of the 5–speed automatictransmissionThis vehicle is equipped with an adaptive Transmission Shift Strategy.Adaptive S
D (Overdrive) with Tow/Haul OFFD (Overdrive) with Tow/Haul OFF is the normal driving position for thebest fuel economy. The overdrive function allows
Used for improved traction on slippery roads. Selecting 3 (Third)provides engine braking.2 (Second)Use 2 (Second) to start-up on slippery roads or to
To start the vehicle:1. Make sure the parking brake is fully set.2. Press the clutch pedal to the floor, then put the gearshift lever in theneutral po
In satellite radio mode (if equipped), press / to tune to thenext/previous channel.Satellite radio is available only with a valid SIRIUS radiosubscrip
Maximum downshift speeds16-speed transmissionShift from: Transfer case position (if equipped)22H or 4H 4LD(Overdrive) - 445 mph (72 km/h) 16 mph (26 k
REVERSE SENSING SYSTEM (IF EQUIPPED)The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when the R (Rev
The RSS detects obstacles up to6 feet (2 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the fi
If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement
Objects in the red zone are closest to your vehicle and objects in thegreen zone are further away. Objects are getting closer to your vehicle asthey m
WARNING: Do not use the camera system with the tailgateopen.If the back end of the vehicle is hit or damaged, then check with yourauthorized dealer to
Manual Shift On Stop (MSOS) 4x4 system (if equipped)The 4WD system is engaged ordisengaged by rotating the controlfor both front wheel hub locks fromt
• uses auto-manual hub locks that can be engaged and disengagedautomatically based on the 4x4 mode selected.• auto-manual hub locks can bemanually ove
2H (2WD) – For general on-road driving. Sends power to the rearwheels only.4H (4x4 High) – For winter and off-road conditions. Sends power tofront and
Shifting from 4H (4x4 High) to 2H (2WD)Move the transfer case lever to 2H(2WD) at a stop or a vehicle speedbelow 5 mph (8 km/h).With the vehicle at co
Customer Assistance 350Reporting safety defects (U.S. only) 356Reporting safety defects (Canada only) 357Cleaning 358Maintenance and Specifications 36
• DELETE SONG: Press OK to delete a song title from the system’smemory. Press/ to cycle through the saved songs. When thesong title appears in the dis
5. If shifting to 2H (2WD) with the vehicle at a complete stop, disengagethe locking hubs (optional) by rotating the hub lock control from LOCKto FREE
Shifting from 2WD to 4x4 HIGHRotate the 4x4 control to the 4x4HIGH position at speeds up to55 mph (88 km/h).• The electronic shift 4x4system is design
3. Move the 4x4 control to the 4x4LOW position.4. Hold the shift conditions until the4x4 LOW indicator light illuminates.5. If the 4x4 LOW indicator l
How your vehicle differs from other vehiclesTruck and utility vehicles can differ from some other vehicles. Yourvehicle may be higher to allow it to t
WARNING: Vehicles with a higher center of gravity such asutility and four-wheel drive vehicles handle differently thanvehicles with a lower center of
WARNING: Vehicles with a higher center of gravity such asutility and four-wheel drive vehicles handle differently thanvehicles with a lower center of
Power is supplied to all four wheels through a transfer case. On 4WDvehicles, the transfer case allows you to select 4WD when necessary.Information on
Be cautious of sudden changes in vehicle speed or direction when youare driving in mud. Even 4WD vehicles can lose traction in slick mud. Aswhen you a
When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This r
Make sure you allow sufficient distance between you and other vehiclesfor stopping. Drive slower than usual and consider using one of the lowergears.
FADE: Press MENU to reach the fade setting. Use / /SEEK, SEEK to adjust the audio between the back (B) andfront (F) speakers.SPEEDVOL (Speed sensitive
VEHICLE USED AS A STATIONARY POWER SOURCEAuxiliary equipment called power take-off, or PTO, is often added to theengine or transmission to operate uti
SNOWPLOWINGFord recommends that the Super Duty F-Series used for snow removalinclude the Snow Plow Package Option.Installing the snowplowWeight limits
• The snow plow prep package includes a unique powertrain controlstrategy which is required for diesel engine cooling during highwaydriving with the s
WARNING: Additional equipment such as snowplow equipmentmay effect the performance of the airbag sensors increasing therisk of injury. Please refer to
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co
FUEL PUMP SHUT-OFF SWITCHThis device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt.After an
FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth
Passenger compartment fuse panelThe fuse panel is located in thepassenger’s footwell. Remove thepanel cover to access the fuses.To remove the fuse pan
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Not used (spare)2 15A Not used (spare)3 15A Family Entertainmen
5. SEEK: In radio mode,press/ to access theprevious/next strong station.In CD/MP3 mode, press/to access the previous/next CD/MP3 track.In satellite ra
Fuse/RelayLocationFuse AmpRatingProtected Circuits10 15A Cargo lamp, Puddle lamp, Switchbacklight11 10A Not used (spare)12 7.5A Power mirror switch, D
Fuse/RelayLocationFuse AmpRatingProtected Circuits29 5A Not used (spare)30 5A Not used (spare)31 10A Not used (spare)32 10A Restraints Control Module
Fuse/RelayLocationFuse AmpRatingProtected Circuits45 5A Front wiper logic, Blower motorrelay coil46 7.5A Not used (spare)47 30A CircuitBreakerPower wi
The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 Relay Blower motor/Variable blowercontrol (Dual Zone C
Fuse/RelayLocationFuse AmpRatingProtected Circuits22 Relay Stop lamps, CenterHigh-Mounted Stop Lamp(CHMSL), TBC, Customer access23 15A** Heater mirror
Fuse/RelayLocationFuse AmpRatingProtected Circuits43 20A* Power point (Center console -Rear)44 30A* Trailer battery charge relay45 30A* Driver power s
Fuse/RelayLocationFuse AmpRatingProtected Circuits66 — Not used67 — Not used68 — Not used69 — Not used70 10A** Gasoline engines: A/C clutchrelay coil,
Your vehicle may be equipped with a conventional spare tire that isdifferent in one or more of the following: type, brand, size, speed ratingand tread
• Use snow chains on the end of the vehicle with the dissimilar sparetire• Use more than one dissimilar spare tire at a time• Use commercial car washi
When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to:• Towing a trailer• Driving vehicles equipped with a
8. FOLDER : In folder mode,press FOLDERto access nextfolder on MP3 discs, if available.9.FOLDER: In folder mode,press FOLDER to access theprevious fol
Use of a temporary spare tire at any one wheel location can lead toimpairment of the following:• Handling, stability and braking performance• Comfort
Location of the spare tire and toolsIf your vehicle is equipped with a spare tire, jack and associated tools,refer to the following table for their lo
• Vehicles equipped with dualrear wheels, insert the lugwrench extension into the lugwrench to reach the lug nuts.2. Attach the spare tire lock key (A
WARNING: To prevent the vehicle from moving when youchange a tire, be sure the parking brake is set, then block (inboth directions) the wheel that is
6. Position the jack according to the following guides:• Front (4x2)• Front driver side (4x4)Note: Make sure the jack fits ontothe flat area on the ou
• RearNever use the front or reardifferential as a jacking point.WARNING: To lessen therisk of personal injury, donot put any part of your bodyunder t
The following steps apply to F–350 Dual Rear Wheel (DRW) andF–450/F–550 vehicles only:11. Slide the notched end of thejack handle over the release val
• Front passenger side (4x4): F-350DRWNote: View shown from the rear ofthe vehicle to clearly identify thejack point.Note: Place the jack directly und
13. Insert the jack handle into thepump linkage.14. Use an up-and-down motionwith the jack handle to raise thewheel completely off the ground.Hydrauli
10–lug nut torque sequence19. Stow the flat tire. Refer to Stowing the flat/spare tire if the vehicleis equipped with a spare tire carrier.Note: Do no
In satellite radio mode (if equipped), press and hold to hear a briefsampling of the next channels. Press again to stop. In CATEGORYMODE, press SCAN t
If the ornament retention towers arealigned between the studs/lug nuts,the ornament is improperlyinstalled. This improper installationmay appear and s
4. Be sure to install all the clips on the nuts over the flanges so thatthere is an even gap all around and the retention clips are fully seated.Stowi
5. Repeat this tightness check procedure when servicing the spare tirepressure (every six months, per scheduled maintenance information),or at any tim
Inspect the wheel pilot hole prior toinstallation. If there is visiblecorrosion in wheel pilot hole,remove loose particles by wipingwith clean rag and
4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level.5. Tu
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
Note: Towing an ESOF 4x4 vehicle with the front wheels on the groundwithout disengaging the front hubs may cause damage to the automatictransmission.N
Premium/Audiophile in-dash six CD/MP3/satellite compatible soundsystem (if equipped)WARNING: Driving while distracted can result in loss of vehiclecon
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized
In Canada:Mailing Address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph
In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is
• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent qu
Satellite radio is available only with a valid SIRIUS radiosubscription. Check with your authorized dealer for availability.2.(Phone): If your vehicle
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
• 6.8L V10 gasoline enginePLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your
• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32–A),available from your au
4. Remove the soaked cloth, and if it is not soiled badly, use this cloth toclean the area by using a rubbing motion for 60 seconds.5. Following this,
INTERIORFor fabric, carpets, cloth seats and safety belts:• Remove dust and loose dirt with a vacuum cleaner.• Remove light stains and soil with Motor
LEATHER SEATS FOR THE KING RANCH F-250 AND F-350 CREWCAB ONLY (IF EQUIPPED)Your vehicle is equipped with seating covered in premium, top-grainleather
ConditioningBottles of King Ranch Leather Conditioner are available at the KingRanch Saddle Shop. Visit the Web site at www.krsaddleshop.com,ortelepho
Motorcraft Dash and Vinyl Cleaner (ZC-38–A)Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A)Motorcraft Detail Wash (ZC-3–A)Motorcraft
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
2. Block the wheels.WARNING: To reduce the risk of vehicle damage and/orpersonal burn injuries, do not start your engine with the aircleaner removed a
song appears in the display that you would like to delete, press OK.The song will appear in the display for confirmation. Press OK againand the displa
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENTRefer to the 6.0 and 6.4 Liter Power Stroke Direct Injection TurboDiesel Owner’s Guide Supplement for
6.8L V10 gasoline engine1. Windshield washer fluid reservoir2. Battery3. Transmission fluid dipstick (automatic transmission)4. Engine oil filler cap5
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the locktab to release the bla
• 5.4L/6.8L gasoline engines only;for diesel engine information,refer to the 6.0 and 6.4 LiterDirect Injection Turbo DieselOwner’s Guide Supplement.6.
4. Install the dipstick and ensure it is fully seated.5. Fully install the engine oil filler cap by turning the filler cap clockwise1/4 of a turn unti
It is recommended you use the appropriate Motorcraft oil filter oranother with equivalent performance for your engine application.BATTERYWARNING: This
WARNING: When lifting a plastic-cased battery, excessivepressure on the end walls could cause acid to flow through thevent caps, resulting in personal
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
To view the station name or type: When the desired category appearsin the display, press TEXT/SCAN to toggle between displaying the stationtype (COUNT
• Add Motorcraft Premium Gold Engine Coolant or equivalentmeeting Ford specification WSS-M97B51-A1. Refer toMaintenance product specifications and cap
Add the proper mixture of coolant and water to the cooling system byfollowing these steps:1. Before you begin, turn the engine off and let it cool.2.
Coolant refill capacityTo find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications and capacities in
What you should know about fail-safe cooling (if equipped)If the engine coolant supply is depleted, this feature allows the vehicle tobe driven tempor
WARNING: Never remove the coolant reservoir cap while theengine is running or hot.5. Re-start the engine and take your vehicle to a service facility.D
Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforerefueling your vehicle.• Al
RefuelingWARNING: Fuel vapor burns violently and a fuel fire can causesevere injuries. To help avoid injuries to you and others:• Read and follow all
If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The vehicle warranty maybe void for any d
Octane recommendationsYour vehicle is designed to use“Regular” unleaded gasoline with apump (R+M)/2 octane rating of 87.We do not recommend the use of
If you have run out of fuel:• You may need to cycle the ignition from off to on several times afterrefueling to allow the fuel system to pump the fuel
COMPRESS (Compression): Available only in CD/MP3 mode. PressMENU until COMPRESS ON/OFF appears in the display.Use/ / SEEK, SEEK to toggle ON/OFF. When
• Use the same filling rate setting (low — medium — high) each timethe tank is filled.• Allow no more than two automatic click-offs when filling.• Alw
• Idling for long periods of time (greater than one minute) may wastefuel.• Anticipate stopping; slowing down may eliminate the need to stop.• Sudden
• Using fuel blended with alcohol may lower fuel economy.• Fuel economy may decrease with lower temperatures during the first8–10 miles (12–16 km) of
WARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine compartment and exhaus
4. Driving through deep water—the electrical system may be wet.These temporary malfunctions can be corrected by filling the fuel tankwith good quality
The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not
7. If the fluid is low, add fluid in small amounts, continuously checkingthe level until it is between the MIN and MAX range. Refer toMaintenance Prod
CLUTCH FLUID (IF EQUIPPED)Check the fluid level. Refer to scheduled maintenance information forthe service interval schedules.During normal operation,
1. Drive the vehicle 20 miles (30 km) or until it reaches normal operatingtemperature.2. Park the vehicle on a level surface and engage the parking br
High fluid levelFluid levels above the safe rangemay result in transmission failure.An overfill condition of transmissionfluid may cause shift and/ore
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
7. SHUFFLE: In CD/MP3 mode,press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engage shuffle mode right away, p
Checking and adding manual transmission fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Fluid leve
TRANSFER CASE FLUID (IF EQUIPPED)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough fluid throughthe fil
AIR FILTERRefer to the scheduled maintenance information for the appropriateintervals for changing the air filter element.When changing the air filter
5. Return air filter cover to originalposition making sure the four tabsare engaged and secure the threeclamps. Tighten clamp on air tubeand reconnect
Replace the spark plugs with ones that meet Ford material anddesign specifications for your vehicle, such as Motorcraft orequivalent replacement parts
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationFront axle 5.8 pints (2.8L)Motorcraft
Item Capacity Ford part nameFord part number /Ford specificationEngine coolant - 6.8LV10 engine227.5 quarts(26.0L)Motorcraft PremiumGold Engine Coolan
Item Capacity Ford part nameFord part number /Ford specificationHinges, latches, strikerplates, fuel filler doorhinge and seat tracks— Multi-Purpose G
Item Capacity Ford part nameFord part number /Ford specificationWindshield washer fluid 3.5 quarts (3.3L)Motorcraft PremiumWindshield WasherConcentrat
ENGINE DATAEngine 5.4L V8 engine 6.8L V10 engineCubic inches 330 415Required fuel 87 octane 87 octaneFiring order 1-3-7-2-6-5-4-8 1-6-5-10-2-7-3-8-4-9
In CD/MP3 mode, press and release to display track title, artist name,and disc title and file name (if available).In satellite radio mode (if equipped
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
LifestyleAsh cup / smoker’s packageBedliners and bedmatsCargo organization and managementTowing mirrorsTrailer hitches, wiring harnesses and accessori
AAccessory delay ...110Air cleaner filter ...402–403Air conditioning ...84Airbag supplemental
washing ...358waxing ...359wheels ...359wiper bl
recommendations ...375refill capacities ...405Event data recording ...7Exhaust fumes ...
Instrument panelcleaning ...362–363cluster ...14lighting up panel andinterior ...
Power distribution box(see Fuses) ...322Power door locks ...155Power mirrors ...
TTailgate ...150Temperature control(see Climate control) ...80Tilt steering wheel ...
To auto load up to 6 discs, press and hold LOAD until the displayreads AUTOLOAD#. Load the desired disc, label side up. The system willprompt you to l
Your vehicle may be equipped withan Auxiliary Input Jack (AIJ). TheAuxiliary Input Jack, located on theinstrument panel below the powerpoint, provides
Troubleshooting:1. Do not connect the audio input jack to a line level output. Line leveloutputs are intended for connection to a home stereo and are
Your vehicle may be equipped with aUSB port located on the instrumentpanel. This feature allows you toplug in media playing devices,memory sticks, and
• Wipe discs from the center out.Don’t:• Expose discs to direct sunlight or heat sources for extended periodsof time.• Clean using a circular motion.C
Audio system warranty and serviceRefer to the Warranty Guide/Customer Information Guide for audiosystem warranty information. If service is necessary,
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m
Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The
Your vehicle may be equipped with a Family Entertainment System(FES) which allows you to listen to audio CDs, MP3 discs, watch DVDsand to plug in and
To play a CD in the DVD system:The DVD system can play audio CDs, CD-R and CD-R/W, CD-ROM andvideo CDs. To ensure proper disc operation, check the dis
1. Ensure that the vehicle is on or the ignition is in accessory mode.2. Press the power button to turnthe DVD system on. The indicatorlight next to t
Note: Channel A can access any possible media source (AM, FM1, FM2,SAT (if equipped), CD, DVD, AUX). Channel B can only access DVD andAUX sources.Note
DVD player controls1. Headphone control A/B: Pressto select either the A or Bheadphone source. Then pressMEDIA to select the desired playingmedia for
4. (Fast forward): Press andrelease for the next chapter ortrack. Press and hold to forwardsearch a DVD, Video CD, or FES CD in DVD/CD mode.5./ (Play/
press the 2 and 4 memory preset buttons on the audio system at thesame time to perform the same function. For further interactioninformation, refer to
1. Power control: Press to turn the FES (Family EntertainmentSystem) ON/OFF.2. Cursor controls: Use in various active menus to advance the cursorup/do
BREAKING-IN YOUR VEHICLEYour vehicle does not need an extensive break-in. Try not to drivecontinuously at the same speed for the first 1,000 miles (1,
8. Fast Forward/Next: In DVD mode, press and hold for a quickadvance within the DVD. Press and release to advance to the nextchapter. In CD/MP3 mode,
Battery replacementBatteries are supplied with the remote control unit. Since all batterieshave a limited shelf life, replace them when the unit fails
HeadphonesWireless headphonesWARNING: The driver should never use the headphones whiledriving the vehicle. Using headphones may prevent the driverfrom
To install the batteries, remove the screw at the bottom of the cover.Then, lightly press down on top and slide the cover off.When replacing the batte
To operate the headphones:• Press POWER on the ear piece to turn on the headphones. A redindicator light will illuminate indicating the headphones are
Wired headphonesWARNING: Do not leave children unattended in the vehicle anddo not let children operate the system while unsupervised. Ifwired headpho
Single Play: Single play consists of all occupants in the vehicle listeningto the same playing media over the front and rear speakers. When theDVD sys
Operation with an aftermarket audio system(Headphone only mode)When the Family Entertainment System (FES) detects that the originalradio supplied by F
This is disc dependent — someDVD discs may have more viewingangles to select from. Once youhave made your selection, pressENTER to confirm. The system
Once you have made your selection,press ENTER to confirm. Thesystem default is English.SubtitlesSelect SUBTITLES to turn thesubtitle option on or off.
Event Data RecordingOther modules in your vehicle — event data recorders — are capable ofcollecting and storing data during a crash or near crash even
COMP (Compression): Compression brings soft and loud CD passagestogether for a more consistent listening level when in CD mode. Press toturn the featu
• Bit rate — The player supports bit rates from 32–320 kbps, as well asvariable bit rate MP3 files, but lower bit rates will have a noticeableeffect o
The FES DVD system is designed to play commercially pressed12 cm (4.75 in) audio compact discs and digital versatile discs(DVD), DVD-R and R/W discs o
Press to adjust volume levels.Slow play1. With a DVD playing, press pause.2. Press and hold the reverse oradvance button to enter into slowplay mode.
On the left side of the system is theHeadphone A input jack. Thisheadphone will listen to the mediaselected on the Channel A source.When you need to m
• : Press to play a DVD or to pause the DVD.When the radio displays “DVD MENU”, press PLAY on the radio(memory preset #6), to play the disc.Parental c
General informationNote: DVDs are formatted byregions. US and Canada systems canonly play region 1 DVDs and Mexicosystems can only play region 4DVDs.
Do not attempt to service, repair or modify the Family EntertainmentSystem (FES). See your dealer.Do not insert foreign objects into the DVD compartme
Federal Communication Commission (FCC) ComplianceChanges or modifications not approved by Ford Lincoln-Mercury could voiduser’s authority to operate t
onto the media controls or into the system. If liquid is accidentallyspilled onto the system, immediately turn the system OFF and consult aqualified s
Vehicle Modification Data RecordingSome aftermarket products may cause severe engine and/or transmissiondamage; refer to the What is not covered secti
HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe
3. Set the fan speed to the highest setting.4. Direct the outer instrument panel vents towards the side windows.To increase airflow to the outer instr
2. Temperature selection: Controls the temperature of the airflow inthe vehicle.3. Air flow selections: Controls the direction of the airflow in theve
Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEMS(IF EQUIPPED)• DATC• DATC with heated mirrors2009 F-250/350/450/550 (f23)Owners Guide, 2nd PrintingUS
• DATC with heated seats and heated mirrorsTemperature conversion: To switch between Fahrenheit and Celsius,refer to Units (English/Metric) under eith
4. Recirculation control: Press to activate/deactivate airrecirculation in cabin. Recirculated air may reduce the amount of time tocool down the inter
Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
In (panel) or (panel/floor) modes:1. Move temperature control to full cold.2. Select A/C and(recirculated air). Use recirculated air with A/C toprovid
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola
Cell phone useThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri
Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the on position,• the head
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicableilluminated switches in the vehicleduring headlamp and parkl
To adjust the headlamps:1. Park your vehicle on a levelsurface about 25 feet (7.6 meters)away from a vertical plain surface(3). Check your headlamp al
5. Locate the vertical adjuster (2)for each headlamp. Adjust the aimby turning the adjuster controleither clockwise (to adjust up) orcounterclockwise
• (4) Horizontal reference line2. Measure the height from thecenter of your headlamp (indicatedby a 3.0 mm circle on the lens) tothe ground and mark a
MAP LAMPS (IF EQUIPPED)The dome lamp turns on when:• any door is opened,• the instrument panel dimmerswitch is rotated up until thecourtesy lamps come
Replacing exterior bulbsCheck the operation of all the bulbs frequently.Function Numberof bulbsTrade numberHeadlamps (aerodynamic) 2 H13/9008Headlamps
Replacing headlamp bulbs (aerodynamic)1. Make sure that the headlamps are off and open the hood.2. Remove the four bolts from thetop, side and bottom
Replacing park/turn and sidemarker lamp bulbs (aerodynamic)1. Make sure that the headlamps are off and open the hood.2. Remove the four bolts from the
2. Remove the three screws and onebolt from the top and bottom of thepark lamp/bezel assembly.3. Remove the four screws and theheadlamp retaining ring
Commentaires sur ces manuels