Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Entertainment Systems 20How to get going 20AM/FM stereo with CD 24AM/FM stereo
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
condensation occurs, a thin film of mist can form on the interior of thelens. The thin mist eventually clears and exits through the vents duringnormal
Function Number of bulbs Trade numberApproach/mirror turnsignal lamps (if equipped)2 906Mirror approachlamps – non turn signal(if equipped)2 *See your
5. Disconnect the electricalconnector.6. Remove the bulb by turning itcounterclockwise and then pulling itstraight out.WARNING: Handle a halogen headl
5. Rotate the bulb socketcounterclockwise and remove fromthe lamp assembly.6. Carefully pull the bulb out of thesocket and push in the new bulb.7. Ins
Replacing the high-mount brakelampTo change the high-mountbrakelamp bulbs:1. Remove the two screws holdingthe lamp assembly in place.2. Pull the lamp
Replacing license plate lamp bulbThe license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
Windshield wiper rainlamp feature (if equipped with Autolamp)When the windshield wipers are turned on during daylight, and theheadlamp control is in t
ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamp.Slide on rod feature (ifequipped)Rotate the visor towards
Conversation mirror (if equipped)On double bin overhead consoles, the conversation mirror allows thedriver to view the rear seating area.WARNING: Do n
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
CENTER CONSOLE (IF EQUIPPED)Your vehicle may be equipped with a variety of console features. Theseinclude:1. Cupholders2. Utility compartment, coin ho
To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe ba
Not equipped with rear climatecontrolCigar/Cigarette lighter (if equipped)Do not plug optional electrical accessories into the cigarette lightersocket
Press and pull the window switchesto open and close windows.• Push down (to the first detent)and hold the switch to open.• Pull up (to the first deten
Bounce-Back (Driver’s window only)When an obstacle has been detected in the window opening as thewindow is moving upward, the window will automaticall
Automatic dimming interior rear view mirrorYour vehicle is equipped with an interior rear view mirror which has anauto-dimming function. The electroni
EXTERIOR MIRRORSPower side view mirrorsThe ignition can be in any position to adjust the power side view mirrors.To adjust your mirrors:1. Rotate the
Note: 10 or more switch activations within one minute, or repeatedfolding/unfolding of the mirrors while holding the switch rearward duringfull travel
Signal indicator mirrors (if equipped)When the turn signal is activated,the lower portion of the mirrorhousing will blink.POWER ADJUSTABLE FOOT PEDALS
Automatic power deploy:• The running boards will extenddown and out when the doors areopened.Automatic power stow:• The running boards will return tot
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa
Note: Do not use the running boards, front and rear hinge assemblies,running board motors, or the running board under body mounts to liftthe vehicle w
3. Press the SET + control andrelease it.4. Take your foot off the acceleratorpedal.5. The indicator lighton theinstrument cluster will turn on.Note:•
Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET + controluntil you get to the desiredspeed,
• Press the speed control OFFcontrol.Note: When you turn off the speedcontrol or the ignition, your speedcontrol set speed memory is erased.STEERING W
In DVD mode (if equipped):• Refer to the Family entertainment DVD system in theEntertainment Systems chapter.In any mode:• Press VOL + or − to adjustv
For further information on the SYNC system, refer to the SYNC威supplement.Navigation system/SYNC威 handsfree control features (ifequipped)Press VOICE br
Bounce-back: When an obstacle has been detected in the moon roofopening as the moon roof is closing, the moon roof will automaticallyopen and stop at
Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink威 equipped vehiclepurchase). I
5. Firmly press and release the “learn” or “smart” button. (The name andcolor of the button may vary by manufacturer.)Note: There are 30 seconds in wh
Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet
WARNING: Under engine misfire conditions, excessive exhausttemperatures could damage the catalytic converter, the fuelsystem, interior floor coverings
STANDARD MESSAGE CENTER (IF EQUIPPED)With the ignition in the on position,the message center, located on yourinstrument cluster, displaysimportant veh
Distance to empty (DTE)Selecting this function from theINFO MENU estimatesapproximately how far you can drivewith the fuel remaining in your tankunder
Outside air temperature (OAT)The outside air temperature isshown together with the compassheading in the bottom row of themessage center display.Compa
5. Press and hold the RESET stem for approximately two seconds toenter the compass zone adjustment mode.6. Press and release the RESET stem until the
Setup menuThis menu allows the user, via the RESET stem located in theinstrument cluster, to interface and control the information displayed inthe mes
Pressing the RESET stem cycles the message center through each of thesystems being monitored. If the RESET stem is not pressed, the displaywill automa
3. Press the RESET stem for the next SETUP MENU item or wait formore than four seconds to return to the INFO MENU (“HOLD RESETFOR SETUP MENU” will app
1. To disable/enable the autounlockfeature, select this function from theSETUP MENU.2. Press and hold the RESET stemfor two seconds to turn theautounl
• They will not reappear until an ignition off-on cycle has beencompleted.• They reappear if the condition clears then reoccurs within the sameignitio
CHECK CHARGING SYSTEM — Displayed when the electrical systemis not maintaining proper voltage when the engine is running. If you areoperating electric
Airbag readiness: If this light failsto illuminate when the ignition isturned to on, continues to flash orremains on, have the systemserviced immediat
XXX MILES TO E FUEL LEVEL LOW — Displayed as an earlyreminder of a low fuel condition.WASHER FLUID LEVEL LOW — Indicates the washer fluid reservoiris
• Average Fuel Economy (AFE)• Instantaneous Fuel Economy• Trip Elapsed Drive Time• Blank ScreenOdometer/Trip odometerRefer to Gauges in the Instrument
Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in miles/gallon orliters/100 km.If you calculate
2. Press and release RESET to pause the timer.3. Press and hold RESET for two seconds in order to reset the timer.Blank screenPress the RESET once to
The sequence of the system check report and how it appears in themessage center is as follows:1. OIL LIFE2. CHARGING SYSTEM3. WASHER FLUID LEVEL4. DOO
Units (English/Metric)1. Select this function from theSETUP menu for the current unitsto be displayed.2. Press the RESET control tochange from English
AutolockThis feature automatically locks all vehicle doors when the vehicle isshifted into any gear, putting the vehicle in motion.1. To disable/enabl
Power Liftgate (if equipped)This feature allows users to open/close the rear liftgate at the touch of abutton.1. To disable/enable the powerliftgate f
Compass zone/calibration adjustment1. Determine your magnetic zone byreferring to the zone map.2. Turn ignition to the on position.3. Start the engine
9. Press the RESET control to startthe compass calibration function.10. Slowly drive the vehicle in acircle (less than 3 mph [5 km/h])until the CIRCLE
Low tire pressure warning (ifequipped): Illuminates when yourtire pressure is low. If the lightremains on at start up or whiledriving, the tire pressu
System warningsSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems.In the event of a multiple warning si
Warning display StatusBrake fluid level low Warning can be reset. Will NOTreturn if reset and warning iscleared and set again withinthe same ignition
PASSENGER DOOR AJAR — Displayed when the passenger door isnot completely closed.REAR LEFT DOOR AJAR — Displayed when the rear left door is notcomplete
WASHER FLUID LEVEL LOW — Indicates the washer fluid reservoiris less than one quarter full. Check the washer fluid level. Refer toWindshield washer fl
TO EXIT 4X4 LOW STOP VEHICLE(if equipped) — Displayed when2WD is selected while the vehicle is operating in 4X4 LOW. For moreinformation, refer to Con
WARNING: Keep keys out of reach of children. Do not allowchildren to play near an open or moving power liftgate.The liftgate will only operate with th
To open the liftgate with outsideliftgate control button (manualactuation):1. To open, unlock the liftgate withthe remote entry transmitter orpower do
To manually operate the liftgate:1. Disable the liftgate power function, refer to the Message center in thischapter.2. Open and close the liftgate as
Liftgate ajar signalIf the liftgate or liftgate glass are not fully latched, you will receive a“LIFTGATE or LIFTGLASS AJAR” message on the instrument
To open the liftgate, push thecontrol button located on the insideof the liftgate handle to unlatch theliftgate, then pull on the handle toaccess the
Four wheel drive low (RTT) (ifequipped): Displays whenfour-wheel drive low is engaged. Ifthe light fails to display when theignition is turned on, or
Cargo shelf/divider (if equipped)The cargo shelf/divider is located behind the rear seat of your vehicle.The shelf has two positions: Flat shelf which
LUGGAGE RACKYour vehicle is equipped with a roofrack for transporting items on theexterior of the vehicle. Themaximum recommended load to becarried on
KEYSYour vehicle may be equipped withtwo Integrated KeyheadTransmitters (IKTs). The key bladefunctions as a programmed keywhich starts the vehicle and
Recommended handling of the Integrated Keyhead Transmitter(IKT)To avoid inadvertently activating the remote entry functions of yourvehicle, it is reco
POWER DOOR LOCKSPress control to unlock all doors.Press control to lock all doors.Smart locksThis feature helps to prevent you from locking yourself o
The autolock feature repeats when:• any door is opened then closed while the ignition is in the on positionand the vehicle speed is 9 mph (15 km/h) or
Keyless entry keypad procedure1. Turn the ignition to the off position.2. Close all doors, the liftgate and liftgate window.3. Enter 5–digit entry cod
Power door lock switch autounlock enable/disable procedureBefore starting, ensure the ignition is in the off position and all vehicledoors are closed.
CHILDPROOF DOOR LOCKSWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo
The typical operating range for your IKT is approximately 33 feet(10 meters). A decrease in operating range could be caused by:• weather conditions,•
Turn signal chime: Sounds when the turn signal lever has beenactivated to signal a turn and not turned off after the vehicle is drivenmore than 1.5 mi
The inside lights will not turn off if:• they have been turned on using the dimmer control or• any door is open.The battery saver feature will turn of
WARNING: Make sure the power liftgate is closed to preventexhaust fumes from being drawn into the vehicle. This will alsoprevent passengers and cargo
3. Within three seconds press the control on the remote entrytransmitter.4. A tone will be heard when the activation is complete.5. Repeat this proced
4. Snap the battery cover back onto the key.Note: Replacement of the battery will not cause the IKT to becomedeprogrammed from your vehicle. The IKT s
The lamps will automatically turn off:• if the ignition switch is turned to the on position, or• thecontrol is pressed, or• after 25 seconds of illumi
The lights will turn off if all the doors remain closed and• 25 seconds elapse, or• the key is inserted in the ignition.Battery saverThe battery saver
• Pressing 1 • 2 assigns driver 1 settings.• Pressing 3 • 4 assigns driver 2 settings.• Pressing 5 • 6, 7 • 8, or 9 • 0 assigns Driver 3 settings.5. T
SECURILOCK™ PASSIVE ANTI-THEFT SYSTEMSecuriLock™ passive anti-theft system is an engine immobilizationsystem. This system is designed to help prevent
Anti-theft indicatorThe anti-theft indicator is located in the instrument panel cluster.• When the ignition is in the offposition, the indicator will
The following items may prevent the vehicle from starting:• Large metallic objects• Electronic devices on the key chain that can be used to purchasega
WARNING: Never remove the coolant reservoir cap while theengine is running or hot.Odometer: Registers the total miles (kilometers) of the vehicle.• Wi
• If two previously programmed coded keys are not available, you musttake your vehicle to your authorized dealer to have the spare key(s)programmed.Pl
To program additional new unprogrammed key(s), wait 20 seconds andthen repeat this procedure from Step 1.PERIMETER ALARM SYSTEM (IF EQUIPPED)The perim
Each door, the hood, and the liftgate is armed individually, and if any areopen, they must be closed before the open entry point (door, hood, orliftga
SEATINGAdjustable head restraintsYour vehicle is equipped with front row outboard head restraints that arevertically adjustable.WARNING: To minimize t
3. Lower the head restraint bypressing and holding the guidesleeve adjust/release button andpushing down on the head restraint.Properly adjust the hea
2. Simultaneously press and holdboth the adjust/release button andthe unlock/remove button, then pullup on the head restraint.To reinstall the adjusta
Lift handle to move seat forward orbackward.Manual seat recliner (if equipped)WARNING: Always drive and ride with your seatback uprightand the lap bel
Using the armrest (if equipped)Push the release control to movethe armrest up or down.Using the manual lumbar support (if equipped)The lumbar support
Using the power lumbar support (if equipped)The power lumbar control is located on the outboard side of the seat.Press the forward side of the control
Move the switch in the direction ofthe arrows to raise or lower the rearportion of the seat cushion.Press the switch in the direction ofthe arrows to
Battery voltage gauge: Indicatesthe battery voltage when theignition is in the on position. If thepointer moves and stays outside thenormal operating
Memory seat/power mirrors/adjustable pedals (if equipped)This system allows automaticpositioning of the driver seat,outside rearview mirrors andadjust
Heated seatsWARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cordinjury, medication,
Climate controlled seats air filter replacement (if equipped)The climate controlled seat system includes air filters that must bereplaced periodically
To install a filter:• First, position the filter in itshousing making sure that the farforward end is all the way up inthe housing. Then push in on th
2. Locate handle on the side of theseat cushion by the door.3. Pull up on the handle and pushthe seatback forward toward thefront of the vehicle.To re
Placing the 2nd row outboard 40% seats in cargo modeWARNING: Use caution when folding the seatback to the flatback position as the system will move fo
Returning to the upright position from full lowered load floorpositionThe seatback cannot be returned to the upright position until the seat isreturne
To return the seat to a seating position:1. Push the seat down and latch tothe floor with a moderate amount ofeffort and speed.2. Make sure the seat i
Exiting the 3rd row1. Pull the strap located at thebottom outboard of the seat back torelease the seat from the floor, androtate the seat up towards t
WARNING: To prevent possible damage to the seat or safetybelts, ensure that the safety belts are not buckled when movingthe seat to the load floor pos
Locks and Security 162Keys 162Locks 164Anti-theft system 177Seating and Safety Restraints 183Seating 183Safety restraints 204Airbags 217Child restrain
AUDIO SYSTEMSQuick start — How to get goingWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly
Adjusting the 2nd row center 20% seat (if equipped)Lift the handle to move the seatforward or backward.Note: This seat can be moved forward to keep a
The rear seat heat controls are located on the rear of the center console.To operate the heated seats:• Push the indicated side of thecontrol for maxi
Folding down the 3rd row seats to the load floorWARNING: To prevent possible damage to the seat or safetybelts, ensure that the safety belts are not b
Third row power folding seat (if equipped)Note: Be sure that the headrestraints are folded down beforepowering the 3rd row seat down.The control butto
opening any door, pressing the unlock button on the key fob,pressing any keyless entry keypad button, or turning the ignitionkey.SAFETY RESTRAINTSPers
Driver and passenger dual-stage airbag supplemental restraintsThe dual-stage airbags offer the capability to tailor the level of airbaginflation energ
Determining if the Personal Safety System姞 is operationalThe Personal Safety System威 uses a warning light in the instrumentcluster or a back-up tone t
WARNING: It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision, people riding inthese areas are more likely
• Front and rear seats2. To unfasten, push the release button and remove the tongue from thebuckle.• Front and rear seatsThe front outboard and rear s
Automatic locking modeIn this mode, the shoulder belt is pre-locked. The belt will still retract toremove any slack in the shoulder belt.The automatic
Listening to satellite radio (if equipped)1. If the audio system is turned off,press VOL-PUSH to turn the radioon. Turn VOL-PUSH to adjust thevolume.N
WARNING: After any vehicle collision, the combination lap andshoulder belt system at all passenger seating positions must bechecked by an authorized d
Safety belt height adjustmentYour vehicle has safety belt heightadjustments for the driver and rightfront passenger. Adjust the height ofthe shoulder
To adjust the comfort guide:1. Slip the shoulder belt into thebelt guide. (The portion of the beltbetween the latch tongue and theD-ring, not the port
Conditions of operationIf... Then...The driver safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt warni
If... Then...The driver’s safety belt isnot buckled approximatelyfive seconds after the safetybelt warning light hasturned off...The Belt-Minder威 feat
Reasons given... Consider...“I was in a hurry” Prime time for an accident.Belt-Minder威 reminds us to take a fewseconds to buckle up.“Safety belts don’
Deactivating/activating the Belt-Minder姞 feature (if equipped)Read Steps1-4thoroughly before proceeding with thedeactivation/activation programming pr
seconds with the light off, then followed by the safety belt warninglight flashing four times per second for three seconds again.AIRBAG SUPPLEMENTAL R
WARNING: The National Highway Traffic Safety Administration(NHTSA) recommends a minimum distance of at least 10 inches(25 cm) between an occupant’s ch
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
For a single CD system, if a discis not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
• one or more impact and safing sensors and diagnostic monitor (RCM),• a readiness light and tone• the electrical wiring which connects the components
WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. Contact your authorize
The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of
WARNING: Do not attempt to service, repair, or modify theSafety Canopy威 system, its fuses, the A, B, C or D pillar trim, orthe headliner on a vehicle
• Two crash sensors mounted in the front doors (one on each side ofthe vehicle).• Two crash sensors located at the C pillar behind the rear doors (one
WARNING: If the SafetyCanopy威 system hasdeployed, the Safety Canopy威 willnot function again unless replaced.The Safety Canopy威 system(including the A,
The S.O.S. Post Crash Alert can be turned off when any one of thefollowing actions are taken by the driver or any other person:• pressing the hazard c
Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommended re-straint typeInfantsor tod-dlersChildren weighing 40
Recommendations for attaching child safety restraints for childrenRe-straintTypeChildWeightUse any attachment method as indicated be-low by “X”LATCH(l
While in folder mode, pressFOLDERto access the nextfolder on MP3 discs, if available.Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe
WARNING: Always carefully follow the instructions andwarnings provided by the manufacturer of any child restraint todetermine if the restraint device
Transporting childrenAlways make sure your child is secured properly in a device that isappropriate for their age, height and weight. All children are
When installing a child safety seat:• Review and follow the informationpresented in the Airbagsupplemental restraint system(SRS) section in this chapt
• Keep the buckle release button pointing up and away from the safetyseat, with the tongue between the child seat and the release button,to help preve
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up
however the safety belt can still be used to attach the child seat. Forforward-facing child seats, the top tether strap must also be attached tothe pr
Follow the instructions on attaching child safety seats with tether straps.Refer to Attaching child safety seats with tether straps later in thischapt
Some of the rear seats of your vehicle are equipped with built-in tetherstrap anchors located behind the seats as described below.In the third row cen
• Second row outboard seatingpositions• Second row center seatingposition (if equipped)3. Grasp the tether strap andposition it to the seat frame.4. R
AM/FM single CD/MP3 satellite compatible sound system(if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and
5. Rotate the tether strap clip.6. Tighten the child safety seat tether strap according to themanufacturer’s instructions.Third row center seating pos
3. Clip the tether strap through theanchor loop as shown.If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly
Booster seats position a child so that vehicle lap/shoulder safety belts fitbetter. They lift the child up so that the lap belt rests low across the h
Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
Move a child to a different seating location if the shoulder belt does notstay positioned on the shoulder during use.Follow all instructions provided
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary
• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and
TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen
In satellite radio mode (if equipped), press / to scrollthrough the SIRIUS channels.Satellite radio is available only with a valid SIRIUS radiosubscri
Glossary of tire terminology• Tire label: A label showing the OE (Original Equipment) tire sizes,recommended inflation pressure and the maximum weight
Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure of all tires and adjust ifrequired
of 1 psi (7 kPa) in inflation pressure. Check your tire pressuresfrequently and adjust them to the proper pressure which can be foundon the Safety Com
TIRE CAREInspecting your tiresPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones, nails or glass that
WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressur
WARNING: Only use replacement tires and wheels that are thesame size, load index, speed rating and type (such as P-metricversus LT-metric or all-seaso
Important: Remember to replace the wheel valve stems when the roadtires are replaced on your vehicle.It is recommended that the two front tires or two
Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your
Note: If your tires show uneven wear ask an authorized dealer to checkfor and correct any wheel misalignment, tire imbalance or mechanicalproblem invo
4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new
The song will appear in the display for confirmation. Press OK againand the display will read SONG DELETED. If you do not want todelete the currently
8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n
13. Maximum Permissible Inflation Pressure: Indicates the tiremanufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including inter
When your temporary spare tire is installedWhen one of your road tires needs to be replaced with the temporaryspare, the TPMS system will continue to
Low TirePressureWarningLightPossiblecauseCustomer Action RequiredFlashingWarningLightSpare tirein useYour temporary spare tire is in use. Repair theda
SNOW TIRES AND CHAINSWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel
capability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design performance. Before loadingyour vehi
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
To activate, press MENU repeatedly until RBDS (ON/OFF) appears inthe display. Use/ / SEEK to toggle RBDS ON/OFF. (WhenRBDS is OFF, you will not be abl
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or performance, e
WARNING: Do not use replacement tires with lower loadcarrying capacities than the original tires because they maylower the vehicle’s GVWR and GAWR lim
• A final example for your vehicle with 1,400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the
Follow these guidelines to ensure safe towing procedure:• Stay within your vehicle’s load limits. If exceeded, cargo should beremoved from the trailer
EngineRear axleratioMaximum GCWR -lb. (kg)Trailer weightrange (0 -maximum) lb. (kg)4x25.4L withstandardtrailer towpackageAll 11800 (5352) 0–6000 (0–27
EngineRear axleratioMaximum GCWR -lb. (kg)Trailer weightrange (0 -maximum) lb. (kg)Expedition EL (U.S. Only) Expedition Max (Canada Only) 4x25.4L with
Integrated hitch ratingThe standard integrated hitch has two ratings depending on mode ofoperation:• Weight carrying - requires a draw bar and hitch b
Weight distributing hitchWhen hooking up a trailer using a load equalizing hitch, always use thefollowing procedure:1. Park the unloaded vehicle on a
The braking system of the tow vehicle is rated for operation at theGVWR not GCWR.Trailer lampsTrailer lamps are required on most towed vehicles. Make
Track/Folder mode: Available only on MP3 discs in CD mode. In Trackmode, pressingSEEK, SEEK will scroll through all tracks on thediscIn Folder mode, p
Trailer towing tips• Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turni
Exceeding these limits may allow water to enter vehicle components:• causing internal damage to the components.• affecting driveability, emissions and
STARTINGPositions of the ignition1. Off— locks the steering wheel,automatic transmission gearshiftlever and allows key removal.2. Accessory— allows th
WARNING: If you smell exhaust fumes inside your vehicle, haveyour dealer inspect your vehicle immediately. Do not drive if yousmell exhaust fumes.Impo
4. Make sure the parking brake isset.5. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminate. See Wa
3. After idling for a few seconds, release the parking brake, apply thebrake, shift into gear and drive.Note: If the engine does not start on the firs
Guarding against exhaust fumesCarbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects.WARNING: If you smell exhaus
WARNING: To reduce the risk of electrical shock, do not useyour heater with ungrounded electrical systems or two-pronged(cheater) adapters.Prior to us
How to use the engine block heaterEnsure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth.Depending on the type
Anti-lock brake system (ABS)On ABS-equipped vehicles, a noise from the hydraulic pump motor andpulsation in the pedal may be observed during ABS braki
press SEEK, SEEK to seek to the previous/next channel in theselected category. Press and holdSEEK, SEEK to fast seekthrough the previous /next channel
Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th
Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.ADVANCETR
WARNING: If a failure has been detected within theAdvanceTrac威 with RSC威 system, the ⬙sliding car⬙ icon willilluminate steadily. Verify that the Advan
When AdvanceTrac威 with RSC威 performs a normal system self-check,some drivers may notice a slight movement of the brake, and/or arumble, grunting, or g
Electronic Stability Control (ESC)Electronic Stability Control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa
The Roll Stability Control system may be deactivated in certainsituations. See the Switching Off AdvanceTrac威 with RSC威 sectionfollowing.Switching Off
STEERINGYour vehicle is equipped with power steering. Power steering uses energyfrom the engine to decrease the driver’s effort in steering the vehicl
AIR SUSPENSION SYSTEM (IF EQUIPPED)The air suspension system is designed to improve ride, handling andgeneral vehicle performance during:• Certain roa
WARNING: In a rollover crash, an unbelted person issignificantly more likely to die than a person wearing a seat belt.Utility vehicles and trucks have
3. Remove the access plug on top ofthe steering column.4. Using a flat-head screwdriver orsimilar tool, move the brake-shiftinterlock actuator spindle
Customer Assistance 348Reporting safety defects (U.S. only) 354Reporting safety defects (Canada only) 354Cleaning 355Maintenance and Specifications 36
10. FF (Fast forward): In CDmode, press FF to manually advancein a track.In DVD mode (if equipped), press and hold to advance through thecurrent chapt
the off position, it is possible that a fuse has blown or the vehicle’sbrakelamps are not operating properly. Refer to Fuses and relays in theRoadside
engine while decelerating. This fuel economy benefit may be perceivedas a light to medium braking sensation when removing your foot fromthe accelerato
N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D
transmission is in the D (Overdrive) position; this engine braking willslow the vehicle and assist the driver in controlling the vehicle whendescendin
If your vehicle gets stuck in mud or snowIf your vehicle gets stuck in mud or snow, it may be rocked out byshifting between forward and reverse gears,
The system will assist the driver in detecting certain objects while thevehicle moves in reverse at speeds less than 6 mph (10 km/h). Thesystem is not
Audible WarningsDistance to Object WarningSpeed above 2.5 mph (4 km/h)up to 1.6 feet (.5 meters) Solid1.6 feet (.5 meters) to 3.1 feet (1 meter) Fast
REARVIEW CAMERA SYSTEM (IF EQUIPPED)The camera system located on theliftgate provides a video image,which appears in the rearviewmirror or on the navi
Note: The default setting for the camera delay is off. Push the “Settings”button found on the navigation screen (if equipped) to set the cameradelay f
Servicing• If the image comes on while the vehicle is not in R (Reverse), havethe system inspected by your authorized dealer.• If the image is not cle
In satellite radio mode (if equipped), press and release to enterTEXT MODE and display the current song title. While in TEXT MODE,press again to scrol
Positions of the Control Trac systemThe Control Trac system functionsin four modes:• 2H (2WD) delivers power to therear wheels only. This isappropriat
WARNING: Utility and four-wheel drive vehicles are notdesigned for cornering at speeds as high as passenger cars anymore than low-slung sports cars ar
AdvanceTrac威 with Roll Stability Control (RSC) StabilityEnhancement System in this chapter) while operating in 2H, 4A or 4Hwhile driving in deep sand,
• It often may be less risky to strike small objects, such as highwayreflectors, with minor damage to your vehicle rather than attempt asudden return
Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,
Normal characteristicsOn some four–wheel drive models, the initial shift from two-wheel driveto four–wheel drive while the vehicle is moving can cause
If the transmission, transfer case, front axle or rear axle are submergedin water, their fluids should be checked and changed, if necessary.Driving th
Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;
Maintenance and ModificationsThe suspension and steering systems on your vehicle have been designedand tested to provide predictable performance wheth
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
Premium/Premium sound AM/FM in-dash six CD/MP3 satellitecompatible sound system (if equipped)WARNING: Driving while distracted can result in loss of v
Canadian customers refer to your Customer Information Guidefor information on:• coverage period• exact fuel amounts• towing of your disabled vehicle•
FUEL PUMP SHUT-OFF SWITCHFUELRESETThe fuel pump shut-off switch is a device intended to stop the electricfuel pump when your vehicle has been involved
FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth
Passenger compartment fuse panelThe fuse panel is located under the right-hand side of the instrumentpanel.To remove the trim panel for accessto the f
The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Smart window #12 15A Driver side memory module3 15A FES, Audio
Fuse/RelayLocationFuse AmpRatingProtected Circuits27 20A Ignition switch28 5A Radio29 5A Instrument panel cluster30 5A Not used (Spare)31 10A Not used
WARNING: To reduce risk of electrical shock, always replacethe cover to the Power Distribution Box before reconnecting thebattery or refilling fluid r
Fuse/RelayLocationFuse AmpRatingProtected Circuits12 40A** Run/Start relay13 30A ** Starter relay14 — Not used15 — Not used16 — Not used17 — Not used1
Fuse/RelayLocationFuse AmpRatingProtected Circuits41 10A* TCM/PCM keep alive power42 — Not used43 15A* Brake on/off switch44 20A* Fuel pump relay45 25
Fuse/RelayLocationFuse AmpRatingProtected Circuits71 20A** Auxiliary power point72 20A** Auxiliary power point73 — Not used74 30A** Driver power seat/
In satellite radio mode (if equipped), press to scroll through theSIRIUS channels.Satellite radio is available only with a valid SIRIUS radiosubscript
WARNING: Refer to Tire pressure monitoring system (TPMS)in the Tires, Wheels and Loading chapter for importantinformation. If the tire pressure monito
• Comfort and noise• Ground clearance and parking at curbs• Winter weather driving capability• Wet weather driving capability3. Full-size dissimilar s
Stopping and securing the vehicle1. Park on a level surface, activatethe hazard flashers and set theparking brake.2. Place the gearshift in P (Park)an
Removing the spare tire1. Remove the jack handle andwinch extension from the tray andassemble them.2. Open the spare tire winch accessplug in the bott
WARNING: Do not attempt to change a tire on the side of thevehicle close to moving traffic. Pull far enough off the road toavoid the danger of being h
5. Position the jack according to thejack locator arrows found on theframe and turn the jack handle andextension tool assembly clockwise.Note: Use the
WARNING: Turn off the running boards (if equipped) beforejacking or placing any object under the vehicle. Never place yourhand between the extended ru
13. Turn on the air suspension system (if equipped). Refer to Messagecenter in the Driver Controls chapter for instructions on turning the airsuspensi
WHEEL LUG NUT TORQUE SPECIFICATIONSRetighten the lug nuts to the specified torque within 100 miles (160 km)after any wheel disturbance (tire rotation,
RUNNING OUT OF FUELIf you have run out of fuel and need to refill the vehicle with a portablefuel container, see Running out of fuel in the Maintenanc
and the display will read SONG DELETED. If you do not want todelete the currently listed song, press/ to select eitherRETURN or CANCEL.Note: If there
Preparing your vehicleWhen the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
4. Make the final connection of the negative (-) cable to the jumpstarting stud located in the engine compartment, near the washer fluidbottle. Do not
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
Remove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the jump starting stud.Note: In the illustration
4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery.After the disabled vehicle has been started and the jumper
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized
In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph
To search for specific RBDS music categories: When the desiredcategory appears in the display, press/ to find the desired type,then press and releaseS
In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext
procedure outlined on the first page of the Customer Assistance section,you may be eligible to participate in the BBB AUTO LINE program.The BBB AUTO L
The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have
If you cannot find unleaded fuel or can only get fuel with an anti-knockindex lower than is recommended for your vehicle, contact a regionaloffice or
Obtaining a French owner’s guideFrench Owner’s Guides can be obtained from your authorized dealer orby writing to:Ford Motor Company of Canada, Limite
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is
• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent qu
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub
• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to a
In Folder mode, pressing SEEK will scroll only through trackswithin the selected folder.PressFOLDER, FOLDER to access the previous/next folder (ifavai
WARNING: Do not use cleaning solvents, bleach or dye on thevehicle’s safety belts, as these actions may weaken the beltwebbing.WARNING: On vehicles eq
LEATHER SEATS FOR THE KING RANCH EXPEDITION ONLY(IF EQUIPPED)Your vehicle is equipped with seating covered in premium, top-grainleather which is extre
ConditioningBottles of King Ranch Leather Conditioner are available at the KingRanch Saddle Shop. Visit the Web site at www.krsaddleshop.com,ortelepho
Motorcraft Detail Wash (ZC-3-A)Motorcraft Dusting Cloth (ZC-24)Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20)Motorcraft Engine Shampoo (C
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
Working with the engine on1. Set the parking brake and shift to P (Park).2. Block the wheels.WARNING: To reduce the risk of vehicle damage and/orperso
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT5.4L V81. Windshield washer fluid reservoir2. Engine oil dipstick3. Brake fluid reservoir4. Engine coo
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
CHANGING THE WIPER BLADESIt is recommended that wiper blades are renewed before winter.To replace the wiper blades:1. Fold back the wiper arm andposit
4. To attach the new wiper to thewiper arm, align the cross pin andkeyway (denoted with the arrows)and firmly press the wiper bladeinto the wiper arm
In TEXT MODE, press SEEK, SEEK to view theprevious/additional display text.Satellite radio is available only with a valid SIRIUS radiosubscription. Ch
• If the oil level is below thismark, engine oil must be addedto raise the level within thenormal operating range.• If required, add engine oil to the
Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by th
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If
WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work
• If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
• Add Motorcraft Premium Gold Engine Coolant or equivalentmeeting Ford specification WSS-M97B51-A1. Refer toMaintenance product specifications and cap
WARNING: To reduce the risk of personal injury, make sure theengine is cool before unscrewing the coolant pressure relief cap.The cooling system is un
Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant since a Ford-approved recycling process is not yet avai
Vehicles driven year-round in non-extreme climates should use a 50/50mixture of engine coolant and distilled water for optimum cooling systemand engin
11. REW (Rewind): In radio mode,press REW to manually reverse in atrack.In DVD mode (if equipped), press to reverse within the current chapter.12. Mem
3. If this is not possible, wait a short period for the engine to cool.4. Check the coolant level and replenish if low.WARNING: Never remove the coola
Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforefueling your vehicle.• Alwa
Pure ethanol is the alcohol which is the intoxicating agent in liquor, beerand wine. It is distilled from the fermentation of plants such as field cor
RefuelingWARNING: Fuel vapor burns violently and a fuel fire can causesevere injuries. To help avoid injuries to you and others:• Read and follow all
Note: A fuel spillage concern may occur if overfilling the fuel tank. Donot overfill the tank to the point that the fuel is able to bypass the fuelfil
Choosing the right fuelUse only UNLEADED FUEL and FUEL ETHANOL (Ed75–Ed85).The use of leaded fuel is prohibited by law and could damage yourvehicle.Yo
Gasolines that meet the World-Wide Fuel Charter should be used whenavailable. Ask your fuel supplier about gasolines that meet theWorld-Wide Fuel Char
• The service engine soon indicator may come on. For moreinformation on the service engine soon indicator, refer to Warninglights and chimes in the In
ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform
Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers).2. Each time you fill the tan
14. AM/FM: Press to selectAM/FM1/FM2 frequency band.15. ON/OFF/Volume: Press to turnON/OFF. Turn to increase/decreasevolume.Note: If the volume is set
• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between the top gears occurs. Unnecessaryshifting of this type co
EPA fuel economy estimatesEvery new vehicle should have a window sticker containing EPA fueleconomy estimates. Contact your authorized dealer if the w
WARNING: Exhaust leaks may result in entry of harmful andpotentially lethal fumes into the passenger compartment.Do not make any unauthorized changes
detected by the OBD-II may not have symptoms that are apparent,continued driving with the service engine soonindicator on canresult in increased emiss
POWER STEERING FLUIDCheck the power steering fluid. Refer to scheduled maintenanceinformation.1. Start the engine and let it rununtil it reaches norma
TRANSMISSION FLUIDChecking automatic transmission fluidThe automatic transmission does not have a transmission fluid dipstick.Refer to your scheduled
2. Unlock the locking clip on theconnector (connector shown frombelow for clarity), then squeeze andpull the connector off of the airoutlet tube.3. Cl
6. Remove the air filter elementfrom the air filter housing.7. Install a new air filter element.8. Replace the air filter housingcover and secure the
Note: Failure to use the correct air filter element may result in severeengine damage. The customer warranty may be void for any damage tothe engine i
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationBrake fluidBetween MIN andMAX on rese
CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The
19. CD slot: Insert a CD label sideup.Auxiliary input jack (Line in)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident a
Item Capacity Ford part nameFord part number /Ford specificationEngine coolant (Baseradiator without auxrear heat)16.4 quarts(15.5L)Motorcraft Premium
Item Capacity Ford part nameFord part number /Ford specificationPower steering fluidFill between MINand MAX lines onreservoirMotorcraftMERCON威 VATFXT-
Item Capacity Ford part nameFord part number /Ford specificationFuel tank(Expedition EL – U.S.only)33.5 gallons(126.8L)Fuel tank(Expedition Max –Canad
ENGINE DATAEngine 5.4L V8 engineCubic inches 330Fuel 87 octane or (E-85)Firing order 1-3-7-2-6-5-4-8Ignition system Coil on plugSpark plug gap 0.039–0
Engine drivebelt routingIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations req
Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX
TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
Peace of mindMobile-Ease™ hands-free communication systemRemote startVehicle security systemsWheel locksFor maximum vehicle performance, keep the foll
AABS (see Brakes) ...289Accessory delay ...114AdvanceTrac ...291Air cleaner filter .
2. Ensure that the battery in your portable music player is new or fullycharged and that the device is turned off.3. Attach one end of the audio exten
Child safety seats - boosterseats ...242Cleaning your vehicleengine compartment ...357instrument pa
checking and adding ...369dipstick ...369filter, specifications ...371, 398recommendations ...
IIgnition ...282, 403–404Illuminated visor mirror ...108Infant seats(see Safety seats) ...231Inspection/
OOctane rating ...385Oil (see Engine oil) ...369PParking brake ...290Parts (see Motor
cleaning...361climate control...192heated...200memory seat...
VVehicle Identification Number(VIN) ...405Vehicle loading ...267Ventilating your vehicle
USB port (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdriver
1. MEDIA: Push repeatedly to cyclethrough available playing mediassuch as AM, FM1, FM2, CD, SAT1,SAT2, SAT3 (satellite radio ifequipped), DVD (if equi
Parental controlPress the memory preset controls 3and 5 simultaneously on the frontaudio controls to disable the rearseat controls. They will remain d
Using headphones/Dual Play modeWARNING: Do not leave children unattended in the vehicle anddo not let children operate the system while unsupervised.
CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C
CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required. Thism
Radio Display Condition Action RequiredNO TEXT Category informationnot available.Category information notavailable at this time onthis channel. The sy
Quick startYour Family Entertainment System includes a DVD system, two sets ofwireless infrared (IR) headphones and a wireless infrared (IR) remotecon
To play a CD in the DVD system:The DVD system can play audio CDs, CD-R and CD-R/W, CD-ROM andvideo CDs. To ensure proper disc operation, check the dis
3. The disc will begin to play andthe ‘MP3 Audio Disc’ screen willdisplay and allow you to access theCOMPRESSION, SHUFFLE, SCANand FOLDER MODE feature
from the auxiliary source, the screen will remain black. If the videosource is set to DVD-AUX, the display will automatically turn on if avideo signal
1. Press the headphone/speaker/ button on the DVDplayer or press the 2 and 4 memorypresets on the radio at the same time.A green light will illuminate
To adjust display brightness:To decrease/increase the brightnesslevel on the display screen, pressthe brightness control on the DVDsystem. A display w
2. / (Stop/Eject): Pressonce to stop and press a secondtime to eject a disc from the DVDsystem.3.(Reverse): Press andrelease for the previous chapter
10. Volume: When in single playmode, press to increase ()ordecrease ( ) the volume over allspeakers. When in Dual Play, pressto increase () or decreas
PERCHLORATE MATERIALCertain components of this vehicle such as airbag modules, seat beltpretensioners, and button cell batteries may contain Perchlora
16. Cursor /Brightness controls:Use the cursor controls to makevarious selections when in anymenu. When not in a menu, and inDVD mode, press/ to adjus
4. RETURN: Press to return to the previous menu screen.5. ANGLE (DVD dependent): Press to select the angle to view thescene.6. Channel A/B: Press to s
18. Fast reverse/Previous: When a DVD is playing, press and hold for aquick reverse within the DVD. Press and release for the previouschapter. Press P
Remove the screw and unlatch the battery cover to access the batteries.The remote control unit uses two AAA batteries which are supplied withthe unit.
To install the batteries, remove the screw at the bottom of the cover.Then, lightly press down on top and slide the cover off.When replacing the batte
To operate the headphones:• Press POWER on the ear piece to turn on the headphones. A redindicator light will illuminate indicating the headphones are
Wired headphonesWARNING: Do not leave children unattended in the vehicle anddo not let children operate the system while unsupervised. Ifwired headpho
Single Play: Single play consists of all occupants in the vehicle listeningto the same playing media over the front and rear speakers. When theDVD sys
Press the Headphone Control buttonA to change the audio source forChannel A.Press MEDIA to change the audiosource for Channel A. Thisinformation will
Press the Headphone Control buttonA to change the audio source forChannel A.Press MEDIA to change the audiosource for Channel A. Thisinformation will
Service Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This pote
Menu modePress MENU once on the DVD system to access the DVD disc menu ifavailable.Press MENU twice to access the DVD set-up menu and the followingfea
You can select from: WIDE, LETTERBOX or PAN SCAN. Once you havemade your selection, press ENTERto confirm. The LCD screen displaywill immediately chan
Once you have made your selection,press ENTER to confirm. This isdisc dependent.Audio CDsTo play audio CDs on your DVD system:1. Ensure that the vehic
4. The folder, track and elapsedtime will appear in the status bar.The screen will list the Artist, Title,Album and File Name.COMP (Compression):Compr
CD, MP3 and CD player care• Handle discs by their edges only. Never touch the playing surface.• Do not expose discs to direct sunlight or heat sources
4. Use the DVD bezel controls to:Press to play or pause a DVD.Press to stop or eject a DVD.Press and release to go to theprevious chapter. Press and h
2. Press the right cursor button. TheDVD will advance one frame. Eachpress of the right cursor button willadvance the DVD video by oneframe.Headphone/
Audio displaysYour DVD system interacts closely with the front audio system. Statusmessages will appear in the radio display showing the DVD status. S
When the DVD system is ON, youcan then press the memory presetcontrols 2 and 4 simultaneously totoggle between Single Play and Dual Play. In Single Pl
Safety informationWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers us
and/or other details about the vehicle or crash to assist 911 operators toprovide the most appropriate emergency services. If you do not want todisclo
Do not operate video games or video equipment if the power cordsand/or cables are broken, split or damaged. Carefully place cords and/orcables where t
Temperature extremesWhen the vehicle is parked under direct sunlight or in an extremely coldplace for a long period of time, wait until the cabin temp
Compatibility with aftermarket audio systems(headphone only mode)When the Family Entertainment System (FES) detects that the originalradio supplied by
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
6. Fan speed adjustment: Controls the volume of air circulated in thevehicle.Manual heating and air conditioning system with rear passengercompartment
4. REAR Rear temperature control: Press to enable theauxiliary system and to set the desired rear cabin airflow temperaturewith the front control. The
the MAX A/C position, turn off the rear A/C unit, reduce blower fanspeed from the highest setting and put the vehicle’s transmission intothe P (Park)
2. Rear temperature control: Press to enable the auxiliary system andset the desired rear cabin airflow temperature with the front control. Therear ca
10. : Distributes air through the instrument panel vents and the floorvents.11.: Distributes air through the instrument panel vents.12. Manual overrid
Dual automatic temperature control with heated and cooled seatsand rear passenger compartment climate control (if equipped)1.Defrost: Distributes outs
WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers use extreme caution
5. R Rear fan speed control: Press to enable the auxiliary systemor to adjust the rear fan speed from the front control. Press to manuallyincrease or
12. F Front fan speed control: Press to manually increase ordecrease the fan speed. To return to full automatic control, press AUTO.13. OFF: Outside a
• To improve the A/C cool down, drive with the windows slightly openfor 2-3 minutes after start up or until the vehicle has been “aired out”.• During
AUXILIARY CLIMATE CONTROL (IF EQUIPPED)1. Fan speed: Turn to select thedesired fan speed.2. Temperature/mode selection:The distribution of air from th
HEADLAMP CONTROLRotate the headlamp control to thefirst positionto turn on theparking lamps.Rotate to the second positiontoturn on the headlamps.Rotat
Fog lamp control (if equipped)The headlamp control also operatesthe fog lamps. The fog lamps can beturned on when the headlampcontrol is in theorposit
WARNING: Always remember to turn on your headlamps atdusk or during inclement weather. The Daytime Running Lamp(DRL) system does not activate the tail
1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters)away.• (1) 8 feet (2.4 meters)• (2) Cen
TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSFront row map lamps (if equipp
Second row map lamps (if equipped)The second row map lamps arelocated in the headliner above thesecond row seats.The second row map lamp lightswhen:•
Commentaires sur ces manuels