Introduction 4Instrument Cluster 10Warning lights and chimes 10Gauges 14Entertainment Systems 16How to get going 16AM/FM stereo with CD 20AM/FM stereo
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A wa
• Press the bottom of the control to adjust the pedals towards you.The adjustment allows for approximately 2.8 inches (71 mm) ofmaximum travel.Never a
3. Press the SET + control andrelease it.4. Take your foot off the acceleratorpedal.5. The indicatorlight on theinstrument cluster will turn on.Note:•
Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET + controluntil you get to the desiredspeed,
Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal or pressCNCL (Cancel). This will noterase your veh
In AM, FM1, or FM2 mode:• Press SEEK to access thenext/previous strong station.In Satellite radio mode (ifequipped):• Press and release SEEK to access
SYNC system hands free controlfeature (if equipped)Pressbriefly to use the voicecommand feature. You will hear atone and LISTENING will appear inthe r
To close the moon roof:To close, press the front portion of the control (to the first detent). Toactivate the automatic, one-touch, express close feat
U.S. federal safety standards (this includes any garage door openermodel manufactured before April 1, 1982). A garage door which cannotdetect an objec
• If the indicator light blinks rapidly for two seconds and then turnsto a constant light continue with “Programming” Steps 4 through6 to complete pro
• Proceed with Step 3 in the “Programming” section.Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate
Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interiorfloor coverings or other
MESSAGE CENTERWith the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle informationthrough
The DTE function will display FUEL LEVEL LOW and a single tonewhen you have approximately 50 miles (80 km) to empty. If you RESETthis warning message,
2. Press and release RESET to pause the timer.3. Press and hold RESET for 2 seconds in order to reset the timer.Compass displayThe compass heading is
4. Press the SETUP controlrepeatedly until the message centersays “RESET FOR ZONE SETTING”.5. Press the RESET control to enterZone Setting mode.6. Pre
Setup menuPress this control for the followingdisplays:• System Check• Oil Life• Language• Units (English/Metric)• Autolamp Delay (if equipped)• Autol
To reset the oil monitoring system to 100% after each oil change[approximately 7,500 miles (12,000 km) or 6 months] perform thefollowing:1. Press the
1. To disable/enable the autolampdelay feature, select this functionfrom the SETUP control for thecurrent display mode.2. Press the RESET control to s
In the event of a multiple warning situation, the message center willcycle the display to show all warnings by displaying each one for severalseconds.
REAR LEFT DOOR AJAR. Displayed when the left rear door is notcompletely closed.REAR RIGHT DOOR AJAR. Displayed when the right rear door is notcomplete
OIL CHANGE REQUIRED/CHANGE OIL SOON. Displayed when theengine oil life remaining is 5 percent or less. When oil life left is between5% and 0%, the CHA
Airbag readiness: If this light failsto illuminate when the ignition isturned to ON, continues to flash orremains on, have the systemserviced immediat
CARGO AREA FEATURESCargo net (if equipped)The cargo net secures lightweightobjects in the cargo area. Attach thenet to the anchors provided. Do notput
KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the lo
When inserting the IKT into theignition cylinder, place your thumbon the center thumb rest of the IKTand forefinger on the logo badge onthe opposite s
Smart locksThis feature helps to prevent you from locking yourself out of the vehicleif your key is still in the ignition.When you open one of the fro
Power door lock switch autolock enable/disable procedureBefore starting, ensure the ignition is in the 1 (LOCK) position and allvehicle doors are clos
Autounlock featureThe autounlock feature will unlock all the doors when:• the ignition is in the 3 (RUN) position, all the doors are closed, andthe ve
6. To enable/disable the autounlock feature, press the lock control, thenpress the unlock control. The horn will chirp once if autounlock wasdeactivat
• When the childproof door locks are set, the rear doors cannot beopened from the inside.• The rear doors can be opened from the outside when the powe
On hot days, the temperature in the trunk or vehicle interior canrise very quickly. Exposure of people or animals to these hightemperatures for even a
If there are problems with the remote entry system, make sure to takeALL Integrated Keyhead Transmitters with you to the authorizeddealer in order to
Low fuel (if equipped):Illuminates when the fuel level inthe fuel tank is at or near empty(refer to Fuel gauge in thischapter).Speed control: Illumina
Note: The panic alarm will only operate when the ignition is in the 1(LOCK) position.Opening the trunkPress twice within 3 seconds to open the trunk.•
Replacing the batteryThe Integrated Keyhead Transmitter uses one coin type three-voltlithium battery CR2032 or equivalent.To replace the battery:1. Tw
Illuminated entryThe interior lamps and puddle lamps (if equipped) illuminate when theIntegrated Keyhead Transmitter or the keyless entry system keypa
1. Place the key in the ignition andturn the ignition to the 3 (RUN)position.2. Press the power door unlockcontrol on the door panel threetimes.3. Tur
KEYLESS ENTRY SYSTEMYou can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• open the trunk.• recall memory seat/power m
Tips:• Do not set a code that uses five of the same number.• Do not use five numbers in sequential order.• The factory set code will work even if you
started unless a coded Integrated Keyhead Transmitter (IKT)programmed to your vehicle is used. The use of the wrong type ofcoded key may lead to a “no
The theft indicator will flash everytwo seconds to act as a theftdeterrent when the vehicle isarmed.Automatic disarmingThe vehicle is disarmed immedia
• If two previously programmed coded keys are not available, you musttake your vehicle to your authorized dealer to have the spare key(s)programmed.Pl
PERIMETER ALARM SYSTEM (IF EQUIPPED)The perimeter anti-theft system will help protect your vehicle fromunauthorized entry.If there is any potential pe
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
• Press the 7 • 8 and 9 • 0controls on the keyless entry padat the same time to lock thedoors (driver’s door must beclosed).There is a 20 second count
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Push release button to lower headrestraint.Using the manual lumbar support (if equipped)The lumbar support control islocated on the outboard side of t
Cover sharp edges on the load to help prevent injury tooccupants. Secure the load to help prevent shifting duringsudden stops.Before returning the sea
Pull lever up to adjust seatback.Before returning theseatback to its originalposition, make sure that cargo orany objects are not trappedbehind the se
To reduce the risk of possible serious injury: Do not hang objectsoff seat back or stow objects in map pocket (if equipped) whena child is in the fron
Press the control (if equipped) torecline the seatback forward orrearward.Heated seats (if equipped)Persons who are unable to feel pain to the skin be
Memory seats/power mirrors/adjustable pedals (if equipped)This system allows automaticpositioning of the driver seat, powermirrors, and adjustable ped
The head restraints can be movedup by pulling up on the headrestraint.Push release button to lower headrestraint.Split-folding rear seatOne or both re
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback.After returning the sea
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe
• Driver’s seat position sensor.• Front passenger sensing system• “Passenger airbag off” or “pass airbag off” indicator lamp• Front crash severity sen
levels of crash severity and modify the deployment strategy of thedual-stage airbags and safety belt pretensioners.Driver’s seat position sensorThe dr
allows your Personal Safety System™ to tailor the airbag deploymentand safety belt pretensioner activation depending upon safety belt usage.Refer to S
Safety belt precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injury, mak
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of l
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could re
hardware, should be inspected after a collision. Ford Motor Companyrecommends that all safety belt assemblies in use in vehicles involved ina collisio
The Belt-Minder威 feature uses information from the front passengersensing system to determine if a front seat passenger is present andtherefore potent
AUDIO SYSTEMSQuick start — How to get goingDriving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recommend
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra
Do not sit on top of a buckled safety belt or insert a latchplateinto the buckle to avoid the Belt-Minder威 chime. To do so mayadversely affect the per
2. Wait until the safety belt warning light turns off (Approximately 1minute).• Step 3 must be completed within 50 seconds after the safety beltwarnin
outboard passenger from certain upper body injuries. The term“supplemental restraint” means the airbags are intended as a supplementto the safety belt
• Recline the seat slightly (one or two degrees) from the uprightposition.Do not put anything on or over the airbag module. Placingobjects on or over
How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suffic
Several air bag system components get hot after inflation. Do nottouch them after inflation.If the air bag has deployed, the air bag will not function
The front passenger sensing system will disable (will not inflate) thefront passenger’s frontal airbag if:• the front passenger seat is unoccupied, or
The front passenger sensing system is designed to enable (may inflate)the front passenger’s frontal airbag anytime the system senses that aperson of a
Sitting improperly out of position or with the seat back reclinedtoo far can take off weight from the seat cushion and affect thedecision of the front
Listening to satellite radio (if equipped)1. If the audio system is turned off,press VOL-PUSH to turn the radioon. Turn VOL-PUSH to adjust thevolume.N
To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a child is in
Any alteration/modification to the front passenger seat mayaffect the performance of the front passenger sensing system.Determining if the system is o
Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See yourauthorized dealer.All
The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuittha
Do not lean your head on the door. The Safety Canopy™ couldinjure you as it deploys from the headliner.Do not attempt to service, repair, or modify th
• A headliner designed to flex open above the side doors to allow SafetyCanopy™ deployment.• The same readiness airbag light, electronic control and d
If the Safety Canopy™system has deployed, theSafety Canopy™ will notfunction again unless replaced.The Safety Canopy™ system(including the A, B, and C
Important child restraint precautionsYou are required by law to use safety restraints for children in the U.S.and Canada. If small children (generally
To improve the fit of both the lap and shoulder belt on children whohave outgrown child safety seats, Ford Motor Company recommends useof a belt-posit
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
For a single CD system, if a discis not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the
Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto
Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in acollision.SAFETY SEATS F
and anchors, refer to Attaching safety seats with tether straps in thischapter. For more information of LATCH anchors refer to Attachingsafety seats w
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a
Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a
4. Open the tether anchor cover.5. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safetyseat may not
Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol.All the LATCH lower anchors areeq
lifting the front of the child seat. Keeping the child seat just touching thevehicle seat gives the best protection in a severe crash.Each time you us
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli
Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random pl
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙blowout⬙,with unexpected loss of
when you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive.2. Remove the cap from the valve on one t
Tire wearWhen the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Buil
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of thetire to set the beads without ad
• Do not run over curbs or hit the tire against a curb when parkingIf your vehicle is stuck in snow, mud, sand, etc., do not rapidlyspin the tires; sp
• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles
Note: If your tires show uneven wear ask an authorized dealer to checkfor and correct any wheel misalignment, tire imbalance or mechanicalproblem invo
Locks and Security 121Keys 121Locks 122Anti-theft system 135Seating and Safety Restraints 141Seating 141Safety restraints 149Airbags 162Child restrain
AM/FM Single CD/MP3 satellite compatible sound system(if equipped)Driving while distracted can result in loss of vehicle control,accident and injury.
4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new
8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n
Label or Tire Label which is located on the B-Pillar or the edge of thedriver’s door. The cold inflation pressure should never be set lower thanthe re
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including inter
When your temporary spare tire is installedWhen one of your road tires needs to be replaced with the temporaryspare, the TPMS system will continue to
Low Tire PressureWarning LightPossible cause Customer Action RequiredSolid Warning Light Tire(s)under-inflated1. Check your tire pressure toensure tir
Low Tire PressureWarning LightPossible cause Customer Action RequiredFlashing WarningLightSpare tire in use Your temporary spare tire is inuse. Repair
How temperature affects your tire pressureThe Tire Pressure Monitoring System (TPMS) monitors tire pressure ineach pneumatic tire. While driving in a
Category Mode under Menu for further information.Satellite radio is available only with a valid SIRIUS subscription.Check with your authorized dealer
• Do not use tire chains, cables, or optional traction devices withoptional P225/55R18 tires.• Install cable chains securely, verifying that the cable
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle.3. Subtract the combined weight of the driver and pas
1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now youhave the load capacity to transport the cement and your friend home.In metric units,
If you use a rental trailer, follow the instructions that the rental agencygives to you.Do not attach safety chains to the bumper.Trailer brakesElectr
Trailer towing tips• Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turni
Note: If you tow your vehicle with all four wheels on the ground, followthese instructions:• Tow only in the forward direction• Release the parking br
Rock, News, etc.) Press OK when the desired category appears in thedisplay. After a category is selected, press SEEK to search for thatspecific catego
STARTINGPositions of the ignition1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and a
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
• Make sure the gearshift lever is inP (Park).3. Turn the key to 3 (RUN) withoutturning the key to 4 (START).Some warning lights will briefly illumina
This vehicle has a computer assisted cranking system which assists instarting the engine. If the ignition key is turned to 4 (START) and thenreleased
with Outdoor Appliances.⬙ Never use an indoor extension cordoutdoors; it could result in an electric shock or fire hazard.• Use a 16 gauge outdoor ext
Make sure system is unplugged and properly stowed before driving thevehicle. While not in use, make sure the protective cover seals theprongs of the e
Even when the ABS is disabled,normal braking is still effective. Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake
Push the parking brake pedaldownward again to release theparking brake. Driving with theparking brake on will cause thebrakes to wear out quickly andr
• Entering a paved road from a gravel road, or vice versa• Hitting a curb while turning• Cornering at excessive speeds while towing a heavily loaded t
All these conditions are normal during AdvanceTrac威 operation.If the AdvaceTrac system is activated for an extended period of time, thebrake portion o
AUTOSET: Press MENU until the display reads AUTOSET. Autosetallows you to set the strongest local radio stations without losing youroriginal manually
During Traction Control™ operation the engine will not “rev-up” whenyou push further on the accelerator. This is normal system behavior.If you should
If the steering wanders or pulls, check for:• an improperly inflated tire• uneven tire wear• loose or worn suspension components• loose or worn steeri
Do not drive your vehicle until you verify that the brakelampsare working.Always set the parking brake fully and make sure the gearshift islatched in
Understanding the gearshift positions of the 6–speed automatictransaxleP (Park)This position locks the transaxle and prevents the front wheels fromtur
D (Drive) with OverdriveThe normal driving position for the best fuel economy. Transaxleoperates in gears one through six.D (Drive) with Overdrive Can
To return to O/D (overdrive mode), press the transmission control switchagain.• The O/D OFF lamp in the instrument cluster will not be illuminated.• T
The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to th
ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED)Your vehicle may be equipped with a full-time All Wheel Drive (AWD)system. With the AWD option, power will b
• It may be safer to stay on the apron or shoulder of the road and slowdown gradually before returning to the pavement. You may losecontrol if you do
not more. Additionally, smooth variations of the accelerator and/orbrake pedal pressure should be utilized if changes in vehicle speed arecalled for.
Recommended level is 1–3; SPEED OFF turns the feature off and level 7is the maximum setting.TRACK/FOLDER MODE: Available only on MP3 discs in CD mode.
Be cautious of sudden changes in vehicle speed or direction when youare driving in mud. Even AWD vehicles can lose traction in slick mud. Aswhen you a
Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;
Maintenance and ModificationsThe suspension and steering systems on your vehicle have been designedand tested to provide predictable performance wheth
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
Canadian customers refer to your Customer Information Guidefor information on:• coverage period• exact fuel amounts• towing of your disabled vehicle•
HAZARD FLASHER CONTROLThe hazard flasher is located on theinstrument panel by the radio. Thehazard flashers will operate whenthe ignition is in any po
FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth
Passenger compartment fuse panelThe fuse panel is located under the instrument panel to the left of thesteering wheel.The fuses are coded as follows.F
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description8 10A Low beam headlamps (right)9 15A Interior lights, Cargo lamps10 15A Ba
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description36 5A PATS module37 10A Climate control38 20A Subwoofer (Audiophile radio)3
(Jazz, Rock, News, etc.), press SEEK, SEEK to seek to theprevious/next channel in the selected category. Press and holdSEEK, SEEK to fast seek through
The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 80A* SPDJB power2 80A* SPDJB power3 30A
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription16 20A** Power point (console)17 10A** Alternator18 — Not used19 — Not used20 40A* Re
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription45 10A** Speed control deactivate switch, Massair flow sensor, Inline module VPWR246
Refer to Tire Pressure Monitoring System (TPMS) in theTires, Wheels and Loading chapter for important information. Ifthe tire pressure monitor sensor
Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following:• Handling, stability and braki
Stopping and securing the vehicle1. Park on a level surface, set theparking brake and activate hazardflashers.2. Place gearshift lever in P (Park)and
To help prevent the vehicle from moving when you change a tire,be sure to place the transaxle in P (Park), set the parking brakeand block (in both dir
3. Put the jack in the jack notchnext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is completely off theground.4. Remove
Stowing the tire and jack1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown.
2. Place the tire, with the wheel facing downward, into the spare tirewell and secure the wheel with the large wing nut.If you are stowing the tempora
10. FF (Fast forward): Press FFto manually advance in a CD/MP3track.11. REW (Rewind): Press REW tomanually reverse in a CD/MP3 track.12. Memory preset
Note: Inspect the wheel pilot holeprior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean r
4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level.5. Tu
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
If the vehicle is towed by other means or incorrectly, vehicledamage may occur.In case of a roadside emergency with a disabled vehicle (without access
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
14. AM/FM: Press to selectAM/FM1/FM2 frequency band.15. ON/OFF/Volume: Press to turnON/OFF. Turn to increase/decreasevolume.Note: If the volume is set
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is
WAXING• Wash the vehicle first.• Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your aut
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
• For routine cleaning, use Motorcraft Detail Wash (ZC-3-A).• If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42).• For plas
INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENSClean the instrument panel, interior trim areas and cluster lens with aclean and damp white cotton clot
Premium/Audiophile AM/FM in-dash six CD/MP3 satellitecompatible sound system (if equipped)Driving while distracted can result in loss of vehicle contr
• If grease or tar is present on the material, spot-clean the area firstwith Motorcraft Spot and Stain Remover (ZC-14). In Canada, useMotorcraft Multi
FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column.2. Go to th
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.5L V6 ENGINE1. Power steering fluid reservoir2. Engine coolant reservoir3. Brake fluid reservoir4. B
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
CHANGING THE WIPER BLADES1. Pull the wiper blade and armaway from the glass. Turn the bladeat a right angle to the arm.2. Squeeze the locking tabs tor
5. Locate and carefully remove theengine oil level dipstick.6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil l
• Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine isoverfilled, some oil must beremoved from the e
to the current engine and emission system protection standards and fueleconomy requirements of the International Lubricant Standardization andApproval
In CATEGORY mode (if equipped), press to scroll through the list ofavailable SIRIUS channel categories.Satellite radio is available only with a valid
It is recommended that the negative battery cable terminal bedisconnected from the battery if you plan to store your vehicle for anextended period of
4. Allow the engine to idle for at least one minute.5. Turn the A/C on and allow the engine to idle for at least one minute.6. Release the parking bra
60%, the engine parts could become damaged or not work properly. A50–50 mixture of coolant and water provides the following:• Freeze protection down t
Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur
remove the coolant pressure relief cap on the radiator of a vehicle withan overflow system, follow these steps to add engine coolant.To reduce the ris
Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium
• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i
Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforerefueling your vehicle.• Al
RefuelingFuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others:• Read and follow all the instr
At the next opportunity, safely pull off of the road, remove the fuel fillercap, align the cap properly and reinstall it. The check fuel caplightor “c
Customer Assistance 267Reporting safety defects (U.S. only) 273Reporting safety defects (Canada only) 274Cleaning 275Maintenance and Specifications 28
• CATEGORY: Press OK to enter category mode. Press / toscroll through the list of available SIRIUS channel Categories (Pop,Rock, News, etc.) Press OK
Your vehicle was not designed to use fuel or fuel additives with metalliccompounds, including manganese-based additives. Studies indicate thatthese ad
Cleaner airFord endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality, per the recommendations in the Choosing the RightF
The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fue
Driving style — good driving and fuel economy habitsGive consideration to the lists that follow and you may be able to changea number of variables and
• Carrying unnecessary weight may reduce fuel economy (approximately1 mpg [0.4 km/L] is lost for every 400 lb [180 kg] of weight carried).• Adding cer
If other than Ford, Motorcraft or Ford-authorized parts are used formaintenance replacements or for service of components affectingemission control, s
2. Poor fuel quality or water in the fuel—the engine may misfire or runpoorly.3. The fuel cap may not have been securely tightened. See Fuel fillercap
The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not
BRAKE FLUIDThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“
7. Remove the dipstick and inspect the fluid level. The fluid should be inthe designated areas for normal operating temperature.Low fluid levelDo not
Satellite radio is available only with a valid SIRIUS radiosubscription. Check with your authorized dealer for availability.AUTOSET: Press MENU until
If an overfill occurs, excess fluidshould be removed by an authorizeddealer.An overfill condition oftransmission fluid may cause shift and/or engageme
6. Replace the air filter housingcover and secure the clamps. Besure that the air cleaner cover tabsare engaged into the slots of the aircleaner housi
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItems CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationBrake fluidBetween MAX a
Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine oil 5.5 quarts (5.2L)Motorcraft SAE 5W-20Premium SyntheticBlend Mo
Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationFuel tank20.5 gallons(77.6L) AWD,PZEV AWD andPZEV FWD——20.0 gallons(75.7L
ENGINE DATAEngine 3.5L-DOHC V6 engineDisplacement 3.5LRequired fuel 87 octaneFiring order 1–4–2–5–3–6Spark plug gap (0.052–0.056 inch) 1.32–1.42 mmIgn
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
Peace of mindRemote startVehicle security systemsWheel locksFor maximum vehicle performance, keep the following information inmind when adding accesso
The default setting is off; increasing your vehicle speed will not changethe volume level.Adjust 1–7: Increasing this setting from 1 (lowest setting)
AAccessory delay ...97AdvanceTrac ...227Air cleaner filter ...310–311Air conditioning ..
plastic parts ...277washing ...275waxing ...276wheels ...
Exhaust fumes ...223FFamily entertainment system ...44Fluid capacities ...312Foglamps ...
autolock ...123keypad ...134locking and unlocking doors ..135programming entry code
Rear seat entertainmentsystem ...44Relays ...246Remote entry system ...
sidewall information ...199snow tires and chains ...209spare tire ...253terminology ...
326
327
328
5. SEEK: In radio mode, press/ to access the previous/nextstrong station.In CD mode, press/ toaccess the previous/next CD track.In satellite radio mod
8. FOLDER : In folder mode,press FOLDERto access nextfolder on MP3 discs, if available.9.FOLDER: In folder mode,press FOLDER to access theprevious fol
In TEXT MODE, sometimes the display requires additional text to bedisplayed. When the “>” indicator is active, press SEEKto view theadditional disp
If there is only one disc present in the system, press .To auto eject up to 6 CDs, press and holduntil the system beginsejecting all loaded discs. If
4. Turn the radio on, using either a tuned FM station or a CD loaded intothe system. Adjust the volume to a comfortable listening level.5. Turn the po
USB port (if equipped)Driving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recommends that drivers useext
CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m
Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The
Your vehicle may be equipped with a Family Entertainment System(FES) which allows you to listen to audio CDs, MP3 discs, watch DVDsand to plug in and
Press the power button to turn thesystem OFF. The indicator light willturn off indicating the system is off.Note: The audio from the DVD system will p
3. The disc will begin to play andthe ’MP3 Audio Disc’ screen willdisplay and allow you to access theCOMPRESSION, SHUFFLE, SCANand FOLDER MODE feature
To listen to audio over the headphones (Dual play mode):1. You may listen to channels A and B over wired or wirelessheadphones. Refer to Using the inf
2. Adjust the volume levels usingthe volume controls on the DVDsystem.To adjust display brightness:To decrease/increase the brightnesslevel on the dis
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
Note: Headphone A can access any possible media (AM, FM1, FM2, SAT(if equipped), CD, DVD, DVD-AUX). Headphone B can only access DVDand DVD-AUX.For fur
9. LCD screen: The eight inch diagonal screen rotates down to view andup into housing to store when not in use. Ensure that the screen islatched into
15. ENTER: Press to select/confirmthe current selection.16. Cursor /Brightness controls:Use the cursor controls to makevarious selections when in anym
1. Power control: Press to turn the FES (Family EntertainmentSystem) ON/OFF.2. Cursor controls: Use in various active menus to advance the cursorup/do
(Wireless headphone volume is controlled with the rotary dial on theright ear piece.)8. Fast Forward/Next: In DVD mode, press and hold for a quickadva
23. ILLUMINATION: Press to illuminate the remote control andbacklight all of the buttons.Battery replacementBatteries are supplied with the remote con
Your FES system is equipped withtwo sets of battery powered,infrared wireless headphones. TwoAAA batteries are needed to operatethe headphones. (Batte
To install the batteries, remove the screw at the bottom of the cover.Then, lightly press down on top and slide the cover off.When replacing the batte
To operate the headphones:• Press POWER on the ear piece to turn on the headphones. A redindicator light will illuminate indicating the headphones are
Wired headphonesDo not leave children unattended in the vehicle and do not letchildren operate the system while unsupervised. If wiredheadphones or au
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Airbag supplemental re
Single Play: Single play consists of all occupants in the vehicle listeningto the same playing media over the front and rear speakers. When theDVD sys
Operation with an aftermarket audio system(Headphone only mode)When the Family Entertainment System (FES) detects that the originalradio supplied by F
This is disc dependent — someDVD discs may have more viewingangles to select from. Once youhave made your selection, pressENTER to confirm. The system
Once you have made your selection,press ENTER to confirm. Thesystem default is English.SubtitlesSelect SUBTITLES to turn thesubtitle option on or off.
SCAN. Once you have highlighted the desired track or function, pressENTER on the DVD bezel to confirm your selection.COMP (Compression): Compression b
• Disc finalization — The disc may be left open for the purpose ofadding sessions to it at a later time, but be sure to close each sessionor the disc
with homemade paper (adhesive) labels should not be insertedinto the FES DVD system. The label may peel and cause the CDor DVD to become jammed. It is
2. Press and hold the reverse oradvance button to enter into slowplay mode. Once in slow play mode,press and release the reverse or advance button rep
The B headphone jack (5) is locatedon the right side of the DVD system.Plug in wired headphones (notincluded) here.Note: The B headphones can onlyacce
FULL (enabled): The FES has control over the primary (speaker) andsecondary (headphone) audio sources.LOCAL: The FES has control over the secondary so
other government authorities or other third parties acting with lawfulauthority. Other parties may seek to access the informationindependently of Ford
use this product in any commercial (i.e. revenue generating) real timebroadcasting (terrestrial, satellite, cable and /or any other media)broadcasting
Be sure to review User Manuals for video games and video gameequipment when used as auxiliary inputs for your Family EntertainmentSystem (FES).Do not
• locations where strong magnetic fields are generated.Temperature extremesWhen the vehicle is parked under direct sunlight or in an extremely coldpla
While operating in Headphone Only Mode, the system will have limitedfunctionality.• The system will only output audio to the headphones. It will not b
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
6. Fan speed adjustment: Controls the volume of air circulated in thevehicle.Operating tips• To reduce fog build up on the windshield during humid wea
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED)1.Defrost: Distributes outside air through the windshield defrosterand demister vents. Can be used
8. : Distributes air through the instrument panel and floor vents.9.: Distributes air through the instrument panel vents.10. Manual override controls:
Dual Zone Automatic Temperature Control with heated seats(if equipped)1.Defrost: Distributes outside air through the windshield defrosterand demister
8.Airflow direction control: Press to toggle through the air distributionmodes listed below. The selected mode will be shown in the display.: Distribu
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
• Do not put objects under the front seats that will interfere with theairflow to the back seats.• Remove any snow, ice or leaves from the air intake
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola
3. Turn the ignition switch to RUN and then back to LOCK.4. Turn the headlamp switch to the autolamp position. The headlampswill turn on.5. Wait the d
Flash to passPull toward you to activate andrelease to deactivate.Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced outpu
AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident the alignment of yo
5. Locate the vertical adjuster oneach headlamp. Using a Phillips #2screwdriver, turn the adjuster eitherclockwise (to adjust down) orcounterclockwise
Your vehicle may also have readinglamps within the rear dome lamp(s).Press the switches on either side ofthe dome lamp to turn on thelamps.BULB REPLAC
Function Number of bulbsTradenumberFog lamp (if equipped) 2 H11Map lamp 2 12V6WDome/reading lamps 3 578All replacement bulbs are clear in color except
2. Reach in behind the headlamp assembly to access the bulb socketsand connectors.3. Remove the inboard rubber bootfrom the lamp assembly by pullingre
Replacing rear brake/tail/turn/backup and side marker lamp bulbsThe brake/tail/turn/backup and side marker lamp bulbs are located in thetail lamp asse
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
Replacing license plate lamp bulbs1. Make sure the headlamp switch isin the OFF position.2. Remove the two screws from thelicense plate lamp assembly.
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT STEERING WHEELTo adjust the steering wheel:1. Pull down and hold the steeringwheel release control.2. Move the steering wheel up ordown until you
INSTRUMENT PANEL STORAGE COMPARTMENTThe storage compartment may beused to secure sunglasses or similarsized objects. Press the control toopen the stor
CENTER CONSOLEYour vehicle may be equipped with a variety of console features. Theseinclude:1. Cupholders2. Utility compartment with coinholder, a cla
To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe ba
Press and pull the window switchesto open and close windows.• Push down (to the first detent)and hold the switch to open.• Pull up (to the first deten
Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controls(except for the driver’s) pres
Automatic dimming interior rear view mirror (if equipped)Your vehicle may be equipped with an interior rear view mirror that hasan auto-dimming functi
To adjust your mirrors:1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror.2. Mo
Commentaires sur ces manuels