Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 16Entertainment Systems 19AM/FM stereo 19AM/FM Stereo single CD/MP3 system 21CDX
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with knee on thechild seat.8. Al
The tether strap anchors in your vehicle are in the following positions(shown from top view):• Bucket seats• 60/40 seatsAttach the tether strap only t
3. Locate the correct anchor for the selected seating position.The tether anchor is located on therear lower portion of the passengerseat.4. Clip the
Center seating locationWhen installing a child safety seat in the front center position, route thetether strap over the center arm rest and clip it to
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary
• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and
TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen
TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air
Label which is located on the B-Pillar or the edge of the driver’s door.The cold inflation pressure should never be set lower than therecommended pres
TIRE CAREInspecting your tiresPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones, nails or glass that
AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressure, etc.)
Only use replacement tires and wheels that are the same size,load index, speed rating and type (such as P-metric versusLT-metric or all-season versus
The tire pressure sensors mounted in the wheels (originally installed onyour vehicle) are not designed to be used in aftermarket wheels.The use of whe
Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your
Note: If your tires show uneven wear ask an authorized dealer to checkfor and correct any wheel misalignment, tire imbalance or mechanicalproblem invo
4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new
8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa
13. Maximum Permissible Inflation Pressure: Indicates the tiremanufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw
Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti
Low TirePressureWarning LightPossiblecauseCustomer Action RequiredSolid WarningLightTire(s)under-inflated1. Check your tire pressure to ensuretires ar
When inflating your tiresWhen putting air into your tires (such as at a gas station or in yourgarage), the Tire Pressure Monitoring System may not res
Follow these guidelines when using snow tires and chains:• Use only SAE Class S chains.• Install chains securely, verifying that the chains do not tou
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
Check fuel cap: Illuminates whenthe fuel cap may not be properlyinstalled. Continued driving withthis light on may cause the Serviceengine soon warnin
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury.Steps for determining the correct l
cement to your home? If you and your friend each weigh 220 lb.(99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 -440 - 1200 = -
4x2 w/manual transmissionEngine Rear axleratioMaximumGCWR - lb.(kg)Maximumtrailerweight - lb.(kg)Maximumfrontal areaof trailer -ft2(m2)Regular Cab w/6
4x2 w/manual transmissionEngine Rear axleratioMaximumGCWR - lb.(kg)Maximumtrailerweight - lb.(kg)Maximumfrontal areaof trailer -ft2(m2)*When towing on
4x4 w/manual transmissionEngine Rear axleratioMaximumGCWR - lb.(kg)Maximumtrailerweight - lb.(kg)Maximumfrontal areaof trailer -ft2(m2)For high altitu
4x2 w/automatic transmissionEngine Rear axleratioMaximumGCWR - lb.(kg)Maximumtrailerweight - lb.(kg)Maximumfrontal areaof trailer -ft2(m2)Regular Cab
4x2 w/automatic transmissionEngine Rear axleratioMaximumGCWR - lb.(kg)Maximumtrailerweight - lb.(kg)Maximumfrontal areaof trailer -ft2(m2)*When towing
4x4 w/automatic transmissionEngine Rear axleratioMaximumGCWR - lb.(kg)Maximumtrailerweight - lb.(kg)Maximumfrontal areaof trailer -ft2(m2)For high alt
Airbag readiness: If this light failsto illuminate when the ignition isturned to ON, continues to flash orremains on, have the systemserviced immediat
Preparing to towUse the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. See your authorized dealer or arel
Trailer lampsTrailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working.
Refer to the following chart for information regarding thefactory-equipped trailer tow connector:Trailer tow connectorColor Function Comment1. Dark Gr
• Anticipate stops and brake gradually.• Do not exceed the GCWR rating or transmission damage may occur.Servicing after towingIf you tow a trailer for
Exceeding these limits may allow water to enter vehicle components:• causing internal damage to the components.• affecting driveability, emissions and
• Place the transmission in N (Neutral).• Do not exceed a distance of 50 miles (80 km).• Do not exceed 35 mph (56 km/h) vehicle speed.• Put 4x4 switch
STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo
When starting a fuel-injected engine, don’t press the accelerator beforeor during starting. Only use the accelerator when you have difficultystarting
If starting a vehicle with an automatic transmission:• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).If starting a vehicle
Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrument Cluster chapter for more informationregarding the warning
Never remove the coolant reservoir cap while the engine isrunning or hot.Foglamps: Illuminates when thefoglamps are turned on. Refer toFoglamp control
ENGINE BLOCK HEATER (IF EQUIPPED)An engine block heater warms the engine coolant which aids in startingand allows the heater/defroster system to respo
• Be sure that areas where the vehicle is parked are clean and clear ofall combustibles such as petroleum products, dust, rags, paper andsimilar items
Four-wheel anti-lock brake system (ABS)This vehicle is equipped with an anti-lock braking system (ABS). A noisefrom the hydraulic pump motor and pulsa
ABS warning lampThe ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringsta
rear brakes, the vehicle’s stopping distance will increase greatly and thehandling of your vehicle will be adversely affected.Pull the release lever t
TRACTION-LOK AXLE (IF EQUIPPED)This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under
If you cannot move the gearshift lever out of P (Park) with ignition inthe ON position and the brake pedal depressed:1. Apply the parking brake, turn
Driving with a 5–speed automatic transmission (if equipped)This vehicle is equipped with an adaptive Transmission Shift Strategy.Adaptive Shift Strate
D (Drive) with OverdriveThe normal driving position for thebest fuel economy. Transmissionoperates in gears one through five.D (Drive) without Overdri
MANUAL TRANSMISSION OPERATION (IF EQUIPPED)Using the clutchThe manual transmission has a starter interlock that prevents crankingthe engine unless the
Speed control (if equipped):Illuminates when the speed controlis engaged. Turns off when thespeed control system is disengaged.Turn signal: Illuminate
Recommended shift speedsDownshift according to the following charts for your specificengine/drivetrain combination:Upshifts when accelerating (for bes
3. Turn the ignition off.Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake
4WD system indicator lights• 4x4 - Momentarily illuminateswhen the vehicle is started.Illuminates when 4H (4WD High)is engaged.• 4x4 LOW – Momentarily
2. On vehicles equipped with an automatic transmission, place thetransmission in N (Neutral); on vehicles equipped with a manualtransmission, depress
If your vehicle goes off the edge of the pavement• If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ea
Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,
Normal characteristicsOn some 4WD models, the initial shift from two-wheel drive to 4x4 whilethe vehicle is moving can cause some momentary clunk and
After driving through mud, clean off residue stuck to rotating driveshaftsand tires. Excess mud stuck on tires and rotating driveshafts causes animbal
Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;
Maintenance and ModificationsThe suspension and steering systems on your vehicle have been designedand tested to provide predictable performance wheth
Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
Canadian customers refer to your Customer Information Guidefor information on:• coverage period• exact fuel amounts• towing of your disabled vehicle•
HAZARD FLASHER CONTROLThe hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ign
The fuel pump shut-off switch islocated on the right side of thepassenger footwell, behind the fusepanel door.To reset the switch:1. Turn the ignition
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 5A Instrument panel dimmer switch2 10A Tra
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description9 5A Cluster air bag indicator10 10A Cluster (RUN/START), 4x4module (RUN/ST
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description29 20A Cigar lighter, Diagnostic connector(OBD II)30 5A Power mirrors31 20A
To reduce risk of electrical shock, always replace the cover tothe Power Distribution Box before reconnecting the battery orrefilling fluid reservoirs
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription9 40A** Ignition switch10 — Not used11 30A** Powertrain Control Module (PCM)relay12 —
Tachometer: Indicates the enginespeed in revolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription37 — Not used38 7.5A* Trailer tow (right turn)39 15A* PCM power40 — Not used41 10A* A
3.0L and 4.0L engines (if equipped)The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 40A*
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription15 — Not used16 — Not used17 40A** Anti-lock Brake System (ABS)module18 — Not used19
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription43 20A* A/C relay coil, IAC, MAFS, HEGO,CMS, VMV solenoid, EGRsolenoid, Heated PCV44
The use of tire sealants may damage your Tire PressureMonitoring System and should not be used.Refer to Tire Pressure Monitoring System (TPMS) in theT
Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following:• Handling, stability and braki
Stopping and securing the vehicle1. Park on a level surface, activatehazard flashers and place gearshiftlever in P (Park) (automatictransmission) or 1
Tool LocationSpare tire Under the vehicle, just forward ofthe rear bumperJack, jack handle, wheel nutwrenchRegular Cab: behind the passengerseat, unde
2. If equipped, unlock and removethe spare tire carrier lock from therear access hole located just abovethe rear bumper and below thetailgate.3. Inser
Tire change procedureWhen one of the front wheels is off the ground, the transmissionalone will not prevent the vehicle from moving or slipping off th
AUDIO SYSTEMSAM/FM stereo (if equipped)Driving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recommends th
• Front• RearTo lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engine when
8. Remove the jack and fully tightenthe lug nuts, in the order shown.Refer to Wheel lug nut torquespecifications later in this chapterfor the proper l
WHEEL LUG NUT TORQUE SPECIFICATIONSRetighten the lug nuts to the specified torque within 100 miles (160 km)after any wheel disturbance (rotation, flat
Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted.Do not attempt to push-start your automatic transmissionvehicle. A
Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling
Seating and Safety Restraints 68Seating 68Safety restraints 71Airbags 86Child restraints 93Tires, Wheels and Loading 105Tire information 107Tire infla
2. CLK —To set the time: Ensurethat your audio system is turned off.Press and hold CLK until the hoursflash in the display. PressAUDIO to adjust the h
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is
• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent qu
• To remove tar and grease, use Motorcraft Bug and Tar Remover(ZC-42), available from your authorized dealer.ENGINEEngines are more efficient when the
7. ON/OFF/Volume: Press to turnthe system ON/OFF. Turn to adjustthe volume levels.If the volume is set above a certainlevel, and the ignition is turne
• 3.0L V6 engine• 4.0L SOHC V6 engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTI
WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub
• Do not use household or glass cleaners as these may damage thefinish of the instrument panel, interior trim and cluster lens.Do not use chemical sol
LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• To clean, use a soft cloth with Motorcraft
Motorcraft Dusting Cloth Mitt (ZC-47)Motorcraft Dusting Cloth (ZC-24)Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20)Motorcraft One Step Wa
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
2. Block the wheels.To reduce the risk of vehicle damage and/or personal burninjuries, do not start your engine with the air cleaner removedand do not
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.3L I4 engine1. Windshield washer fluid reservoir2. Engine coolant reservoir3. Engine oil dipstick4.
3.0L V6 engine1. Engine coolant reservoir2. Windshield washer fluid reservoir3. Engine oil filler cap4. Automatic transmission fluid dipstick (if equi
4.0L SOHC V6 engine1. Windshield washer fluid reservoir2. Automatic transmission fluid dipstick (if equipped)3. Engine oil filler cap4. Engine oil dip
1. CD eject: Press to eject theCD/MP3.2. CLK (Clock): Press CLK untilSELECT HOUR or SELECT MINS isdisplayed. PressMENU to adjust thehours/minutes. Pre
WINDSHIELD WASHER FLUID• 2.3L engine• 3.0L and 4.0L enginesAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the re
If you operate your vehicle in temperatures below 40° F (4.5°C),use washer fluid with antifreeze protection. Failure to usewasher fluid with antifreez
4. Open the hood. Protect yourself from engine heat.5. Locate and carefully remove the engine oil level dipstick.• 2.3L I4 engine• 3.0L V6 engineMAXMI
• 4.0L SOHC V6 engine6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil level is between the two holes or betwee
• 3.0L V6 engine• 4.0L SOHC V6 engine• Oil levels above the upper hole or MAX mark may cause enginedamage. Some oil must be removed from the engine by
Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t
Do not use supplemental engine oil additives, cleaners or other enginetreatments. They are unnecessary and could lead to engine damage thatis not cove
that does not meet Ford material and design specifications, start-upengine noises or knock may be experienced.It is recommended you use the appropriat
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a
will not affect function or durability of the transmission. Over time theadaptive learning process will fully update transmission operation to itsopti
Press SEEK to access the saved songs and press MENU tocycle through the saved songs. When the song appears in the displaythat you would like to replac
• 2.3L engines• 3.0L and 4.0L engines2008 Ranger (ran)Owners Guide (post-2002-fmt)USA (fus)Maintenance and Specifications230
When the engine is cold, check the level of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“C
• Do not add/mix an orange-colored, extended life coolant suchas Motorcraft Specialty Orange Engine Coolant, meeting Fordspecification WSS-M97B44-D, o
4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap.5. Fill the coolant reservoi
Severe climatesIf you drive in extremely cold climates (less than –34°F [–36°C ]):• It may be necessary to increase the coolant concentrationabove 50%
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsDo not overfill the fuel tank. The pressure in an overfilled tankmay cause leak
• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek med
Use the following guidelines to avoid electrostatic charge build-up whenfilling an ungrounded fuel container:• Place approved fuel container on the gr
The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stopsbefore completely rem
Octane recommendationsYour vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofga
Balance: Press MENU to adjust the audio between the left andright speakers.Fade: PressMENU to adjust the audio between the front andrear speakers.Next
• Normally, adding 1 gallon (3.8L) of fuel is enough to restart theengine. If the vehicle is out of fuel and on a steep grade, more than 1gallon (3.8L
• Use a known quality gasoline, preferably a national brand.• Use the same side of the same pump and have the vehicle facing thesame direction each ti
• Sudden or hard accelerations may reduce fuel economy.• Slow down gradually.• Driving at reasonable speeds (traveling at 55 mph [88 km/h] uses 15%les
• Transmissions give their best fuel economy when operated in the topcruise gear and with steady pressure on the gas pedal.• Four-wheel-drive operatio
Illumination of the indicator, charging system warning light or thetemperature warning light, fluid leaks, strange odors, smoke or loss ofengine power
These temporary malfunctions can be corrected by filling the fuel tankwith good quality fuel, properly tightening the fuel cap or letting theelectrica
Allow the vehicle to sit for at least eight hours without starting theengine. Then, start the engine and complete the above driving cycle. Theengine m
• 4.0L V6 engineCheck the power steering fluid. Refer to the scheduled maintenanceguide for the service interval schedules.1. Start the engine and let
BRAKE FLUIDThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“
TRANSMISSION FLUIDChecking automatic transmission fluid• Refer to scheduled maintenance information for scheduled checkand change intervals.• Transmis
In satellite radio mode (if equipped), there are 18 available presets,six each for SAT1, SAT2 and SAT3. To save satellite channels in yourmemory prese
Low fluid levelDo not drive the vehicle if the fluidlevel is at or below the bottom ofthe dipstick.High fluid levelFluid levels above the safe rangema
Use only fluid that meets Ford specifications. Refer to the Maintenanceproduct specifications and capacities section in this chapter.TRANSFER CASE FLU
To reduce the risk of vehicle damage and/or personal burninjuries do not start your engine with the air cleaner removedand do not remove it while the
MOTORCRAFT PART NUMBERSComponent 2.3L I4engine3.0L V6 engine 4.0L V6 engineAir filterelementFA-1658 FA-1658 FA-1658Fuel filter FG-1036 FG-1036 FG-1036
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord part name orequivalentFord part number /Ford specificationBrake fluid and (clutchfl
Item CapacityFord part name orequivalentFord part number /Ford specificationEngine coolant (2.3Lengine with manualtransmission)10.5 quarts(10.0L)Motor
Item CapacityFord part name orequivalentFord part number /Ford specificationEngine oil (2.3L engine)4.0 quarts(3.8L)Motorcraft SAE 5W-20Premium Synthe
Item CapacityFord part name orequivalentFord part number /Ford specificationTransfer case fluid(4X4)1.25 quarts(1.2L)Motorcraft Transfer CaseFluidXL–1
Item CapacityFord part name orequivalentFord part number /Ford specificationFuel tank–SuperCab19.5 gallons(73.8L)——1Add the coolant type originally eq
ENGINE DATAEngine 2.3L I4 engine 3.0L V6 engine 4.0L V6 engineCubic inches 138 182 245Required fuel 87 octane 87 octane 87 octaneFiring order 1-3-4-2
14. AUX: Press repeatedly to scrollthrough SAT1, SAT2, SAT3 (SatelliteRadio modes, if equipped) and LINEIN (Auxiliary audio mode, if equipped).For fur
• 3.0L V6 Engine with A/C• 4.0L V6 Engine2008 Ranger (ran)Owners Guide (post-2002-fmt)USA (fus)Maintenance and Specifications260
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
LifestyleAsh cup / smoker’s packageBedliners and bedmatsCargo organization and managementTrailer hitches, wiring harnesses and accessoriesTripTunes™ A
AABS (see Brakes) ...152Air cleaner filter ...251, 253Airbag supplemental restraintsystem ...
waxing ...208wheels ...208wiper blades ...211Clock adjus
electronic shift ...162indicator light ...162preparing to drive yourvehicle ...
headlamps, flash to pass ...44instrument panel, dimming ...44interior lamps ...47–48replacing bulbs ...
Occupant ClassificationSensor ...73safety belt maintenance ...80warning light and chime ...81Safet
Premium and Audiophile In-dash CD6/MP3 disc satellitecompatible audio systems (if equipped)Driving while distracted can result in loss of vehicle cont
VVehicle Identification Number(VIN) ...261Vehicle loading ...127camper bodies ...
271
272
3. AUX: Press AUX repeatedly tocycle through SAT1, SAT2, SAT3(Satellite radio modes, if equipped)and LINE IN (Auxiliary audio mode,if equipped).For mo
ROCK). You may also select CATEGORY ALL to seek all availableSIRIUS categories and channels. Press SEEKto close and returnto the main menu.• SAVE SONG
Maintenance and Specifications 215Engine compartment 217Engine oil 221Battery 227Engine coolant 229Fuel information 235Air filter(s) 251Part numbers 2
Satellite radio is available only with a valid SIRIUS radiosubscription. Check with your authorized dealer for availability.AUTOSET: Allows you to set
10. COMP (Compression): InCD/MP3 modes, press to bring loudand soft passages together for amore consistent listening level.11. REPEAT: Press to repeat
Satellite radio is available only with a valid SIRIUS subscription.Check with your authorized dealer for availability.16. TEXT/SCAN: In radio and CDmo
Auxiliary input jack (Line in)Your vehicle may be equipped withan Auxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your po
Troubleshooting:1. Do not connect the audio input jack to a line level output. Line leveloutputs are intended for connection to a home stereo and are
CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C
CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen
SIRIUS satellite radio service: SIRIUS Satellite Radio is a subscriptionbased satellite radio service that broadcasts music, sports, news andentertain
Radio Display Condition Action RequiredINVALID CHNL Channel no longeravailable.This previouslyavailable channel is nolonger available. Tuneto another
Radio Display Condition Action RequiredNO SIGNAL Loss of signal fromthe SIRIUS satellite orSIRIUS tower to thevehicle antenna.You are in a locationtha
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe
To aid in side window defogging/demisting in cold weather:1. Select.2. Adjust the temperature control to maintain comfort.3. Set the fan speed to the
Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Foglam
Flash to passPull toward you slightly to activateand release to deactivate.Daytime running lamps (DRL) (if equipped)The daytime running light system t
Note: If the battery is disconnected, discharged, or a new battery isinstalled, the dimmer switch requires re-calibration. Rotate the dimmerswitch fro
3. Turn on the low beam headlampsand open the hood.4. Locate the high intensity area ofthe beam pattern and place the topedge of the intensity zone ev
TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSCourtesy/reading lamps (if equ
Function Number of bulbs Trade numberPark/turn (front) 2 3157 A (amber)Sidemarker lamps 2 194 NAHeadlamps 2 9007Fog lamps (ifequipped)29145Hi-mount br
Replacing headlamp bulbs/front park bulbs/turn signal bulbsTo remove the bulb(s):1. Make sure the headlamp switch isin the OFF position, then open the
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
Replacing front sidemarker bulbs1. Turn the headlamp switch to theOFF position and then open thehood.2. At the back of the headlamp, pryup the two ret
Replacing tail lamp/backup lamp bulbs1. Make sure the headlamp switch isin the OFF position and the openthe tailgate to expose the lampassemblies.2. R
Install the new bulb in reverse order.Replacing high-mount brakelamp bulb1. Make sure the headlamp switch isin the OFF position and remove thetwo scre
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers(from desired interval to low or hi
TILT STEERING WHEEL (IF EQUIPPED)To adjust the steering wheel:1. Pull and hold the steering wheelrelease control toward you.2. Move the steering wheel
The auxiliary power points arelocated on the instrument panel.Do not use the power point foroperating the cigarette lighterelement (if equipped).To pr
Press and pull the window switchesto open and close windows.• Push down (to the first detent)and hold the switch to open.• Pull up and hold the switch
Fold-away mirrorsPull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.SPEED CONTROL (IF EQUIPPED)With spee
Disengaging speed controlTo disengage the speed control:• Depress the brake pedal or• Depress the clutch pedal (if equipped).Disengaging the speed con
• Depress the brake pedal or theclutch pedal (if equipped) untilthe desired vehicle speed isreached, press the SET + control.Turning off speed control
SPECIAL NOTICESNew Vehicle Limited WarrantyFor a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited
4. Evenly push down on the bedextender and push the lever in oneach side locking it in place.To stow the bed extender, followsteps one through four in
KEYSThe key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency.If
Your vehicle is equipped with a remote entry system which allows you to:• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta
Note: The panic alarm will only operate when the ignition is in the 2(LOCK) or 3 (OFF) position.Replacing the batteryThe remote entry transmitter uses
Replacing lost remote entry transmittersIf you would like to have your remote entry transmitter reprogrammedbecause you lost one, or would like to buy
Illuminated entryThe interior lamps illuminate when the remote entry system is used tounlock the door(s) or sound the personal alarm.The illuminated e
Anti-theft indicatorThe anti-theft indicator is located inthe instrument cluster.Vehicles equipped with the SecuriLock™ Passive Anti-theft systembehav
• If no previously programmed coded keys are available, you must takeyour vehicle to your authorized dealer to have the spare key(s)programmed.1. Inse
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Lift the release bar to move seatforward or backward. Ensure thatthe seat is locked into place.Pull lever located at the side of theseat cushion up to
Event Data RecordingOther modules in your vehicle — event data recorders — are capable ofcollecting and storing data during a crash or near crash even
Using the manual lumbar support (if equipped)Turn the lumbar support controlclockwise to increase firmness.Turn the lumbar support controlcounterclock
Center facing jump seat (4 door SuperCab) (if equipped)To open, pull seat assembly down,then raise seatback.To stow the seat, fold seat backdown and r
• Restraint system warning light and back-up tone.• The electrical wiring for the airbags, crash sensor(s), safety beltpretensioners, front safety bel
Front passenger sensing systemFor airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occu
Front outboard safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts
Safety restraints precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injur
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
Shorten and fasten the belt whennot in use.For the rear jump seat, shorten andfold the belt into the seat when notin use.Energy Management Feature• Th
How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt
BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe safety belt assembly “automatic locking retractor” feature orany other safety belt function is not
Using your vehicle with a snowplowDo not use this vehicle for snowplowing.Your vehicle is not equipped with a snowplowing package.Using your vehicle a
• 2–door SuperCabTo lower the shoulder belt height, push the button and slide the heightadjuster down. To raise the height of the shoulder belt, push
equipped), child safety seat tether anchors, and attaching hardware,should be inspected after a collision. Ford Motor Company recommendsthat all safet
Belt-Minder姞The Belt-Minder威 feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders byinterm
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate
• The ignition switch is in the OFF position• The driver and front passenger safety belts are unbuckledWhile the design allows you to deactivate your
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The airbag supplemental restraint system is designed to work inconjunction with the safety belts to help pro
Rear facing child seatsshould NEVER be placed infront of an active airbag.All occupants of the vehicle,including the driver, shouldalways properly wea
The front passenger airbag is not designed to offer protection toan occupant in the center front seating position.Modifying or adding equipment to the
How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustainssufficient longitudinal decelera
Export unique (Non–United States/Canada) vehicle specificinformationFor your particular global region, your vehicle may be equipped withfeatures and o
If the airbag has deployed, the airbag will not function againand must be replaced immediately. If the airbag is notreplaced, the unrepaired area will
The front passenger sensing system is designed to meet the regulatoryrequirements of Federal Motor Vehicle Safety Standard (FMVSS) 208and is designed
When the passenger sensing system has allowed the air bag to beenabled, the indicator will be unlit and stay unlit to remind you that theair bag is en
In case there is a problem with thepassenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. DoNOT attempt to repair
Important child restraint precautionsYou are required by law to use safety restraints for children in the U.S.and Canada. If small children ride in yo
To improve the fit of both the lap and shoulder belt on children whohave outgrown child safety seats, Ford Motor Company recommends useof a belt-posit
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto
Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in acollision.SAFETY SEATS F
Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a seating position with a tetheranchor. For
Commentaires sur ces manuels