Ford 2008 Mustang v.3 Manuel d'utilisateur

Introduction 4Instrument Cluster 10Warning lights and chimes 10Gauges 15Entertainment Systems 19How to get going 19AM/FM stereo with CD 23AM/FM stereo

WARNING LIGHTS AND CHIMESBase instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that maybeco

Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop.Always drive and ride with your seatback upright and

Move the switch in the direction ofthe arrows to raise or lower thefront portion of the seat cushion.Move the switch in the direction ofthe arrows to

Note: Do not do the following:• Place heavy objects on the seat• Operate the seat heater if water or any other liquid is spilled on theseat. Allow the

To lower the seatback(s) frominside the vehicle, pull strap torelease seat back and then foldseatback down.When raising the seatback(s), make sure you

• Restraint system warning light and back-up tone.• The electrical wiring for the airbags, crash sensor(s), safety beltpretensioners, front safety bel

Front passenger sensing systemFor airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occu

Front safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly ag

Safety restraints precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injur

Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Checkseat covers and buckle

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.The center of the rear seat is NOT designed as a seatingposition and is no

Service Engine Soon: The ServiceEngine Soon indicator lightilluminates when the ignition is firstturned to the ON position to checkthe bulb and to ind

Failure to replace the Belt and Retractor assembly couldincrease the risk of injury in collisions.The front and rear safety restraints in the vehicle

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl

Safety belt pretensionerYour vehicle is equipped with safety belt pretensioners at the driver andfront outboard passenger seating positions.The safety

Failure to inspect and if necessary replace the safety beltassembly under the above conditions could result in severepersonal injuries in the event of

Both the driver’s and passenger’s safety belt usages are monitored andeither may activate the Belt-Minder威 feature. The warnings are the samefor the d

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra

Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate

• The gearshift is in N (Neutral) (Manual transmission)• The ignition switch is in the OFF position• The driver and front passenger safety belts are u

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

Never place your arm over the airbag module as a deployingairbag can result in serious arm fractures or other injuries.To properly position yourself a

Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance mayoccur. It will take you longer

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

Several air bag system components get hot after inflation. Do nottouch them after inflation.If the air bag has deployed, the air bag will not function

The front passenger sensing systemuses a ⬙passenger airbag off⬙ or⬙pass airbag off⬙ indicator which willilluminate and stay lit to remind youthat the

• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LampPasseng

ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. 3 ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase, ful

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi

Do not use accessory seat covers. The use of accessory seatcovers may prevent the deployment of the side airbags andincrease the risk of injury in an

The side airbags are fitted on the outboard side of the seatbacks of thefront seats. In certain lateral collisions, the airbag on the side affected by

A difficulty with the system is indicated by one or more of the following:• The readiness light will eitherflash or stay lit.• The readiness light wil

Engine coolant temperature:Illuminates when the engine coolanttemperature is high. Stop thevehicle as soon as possible, switch off the engine and let

Children and safety beltsIf the child is the proper size, restrain the child in a safety seat. Childrenwho are too large for child safety seats (as sp

Booster seats should be used until you can answer YES to ALL of thesequestions:• Can the child sit all the way backagainst the vehicle seat back withk

Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto

SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully fo

Carefully follow all of the manufacturer’s instructions includedwith the safety seat you put in your vehicle. If you do not installand use the safety

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a c

Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a

3. Locate the correct anchor for theselected seating position as shownpreviously.For Coupe only:4. Open the tether anchor covers.2008 05+ Mustang (197

5. Clip the tether strap to theanchor as shown.For Convertible only:The tether anchors on theconvertible are located rearward ofthe seatback in the co

Speed control (if equipped):Illuminates when the speed controlis engaged. Turns off when thespeed control system is disengaged.Door/Trunk ajar (if equ

Note: The attachments for theconvertible boot located on the backof the head restraints are not tetheranchors.4. Access tether anchors locatedbehind t

5. Clip the tether strap to theanchor as shown.If the tether strap is clipped incorrectly, the child safety seatmay not be retained properly in the ev

Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol.The center of the rear seatis NOT

If you install a child seat with rigid LATCH attachments, do not tightenthe tether strap enough to lift the child seat off the vehicle seat cushionwhe

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o

Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙blowout⬙,with unexpected loss of

Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them

Key-in-ignition warning chime: Sounds when the key is left in theignition in the OFF/LOCK or ACCESSORY position and the driver’s dooris opened.Headlam

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of thetire to set the beads without ad

• Do not run over curbs or hit the tire against a curb when parkingIf your vehicle is stuck in snow, mud, sand, etc., do not rapidlyspin the tires; sp

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can b

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

Refer to Message center (if equipped) in the Driver Controls chapterto select one of six preset colors or one user definable color (MyColor)for the ni

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti

When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.

Low TirePressureWarning LightPossiblecauseCustomer Action RequiredFlashing WarningLightSpare tire inuseYour temporary spare tire is in use.Repair the

SNOW TIRES AND CHAINSDriving too fast for conditions creates the possibility of loss ofvehicle control. Driving at very high speeds for extended perio

capability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design performance. Before loadingyour vehi

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

Steps for determining the correct load limit:1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.

• Optional instrument clusterRefer to Message center in theDriver Controls chapter on how toswitch the display from Metric toEnglish.Trip odometer: Re

calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 -540 = -103 kg. You will need to reduce the load weight by at least240 lb. (104

Safety chainsAlways connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cr

• Shift out of D (Overdrive) into D (Overdrive cancelled) or a lowergear (3, 2, or 1) when towing up or down steep hills. This willeliminate excessive

STARTINGPositions of the ignition1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval.Note: The ignition

Do not start your vehicle in a closed garage or in other enclosedareas. Exhaust fumes can be toxic. Always open the garage doorbefore you start the en

If starting a vehicle with an automatic transmission:• Make sure the gearshift is in P(Park).• Make sure the parking brake isset.If starting a vehicle

3. Turn the key to 3 (ON) withoutturning the key to 4 (START).Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrum

Important ventilating informationIf the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least one inch (2.

• To reduce the risk of electrical shock, do not use your heater withungrounded electrical systems or two pronged (cheater) adapters.Also ensure that

Refer to Brake system warninglight in the Instrument Clusterchapter for information on the brakesystem warning light.Four-wheel anti-lock brake system

Battery voltage gauge(if equipped): Indicates thebattery voltage when the ignition isin the ON position. If the pointermoves and stays outside the nor

Parking brakeTo set the parking brake (1), pullthe parking brake handle up as faras possible.The BRAKE warning lamp willilluminate and will remainillu

The Traction Control™ system will allow your vehicle to make better useof available traction on slippery surfaces while you are trying toaccelerate or

STEERINGTo help prevent damage to the power steering system:• Never hold the steering wheel at its furthest turning points (until itstops) for more th

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED)Brake-shift interlockThis vehicle is equipped with a brake-shift interlock feature that preventsthe gear

Understanding the gearshift positions of the 5–speed automatictransmissionThis vehicle is equipped with an Adaptive Transmission Control Strategy.This

To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)Always set the parking brake full

• To return to Overdrive mode, press the transmission control switch.The O/D OFF lamp will not be illuminated.• Overdrive mode is automatically return

MANUAL TRANSMISSION OPERATION (IF EQUIPPED)Using the clutchThe manual transmission has a starter interlock that prevents crankingthe engine unless the

Recommended shift speedsDo not downshift into 1 (First) when your vehicle is movingfaster than 15 mph (24 km/h). This will damage the clutch.Upshift a

DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th

AUDIO SYSTEMSQuick start — How to get goingDriving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recommend

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford Motor Companyoffers a complimentary roadside

Using roadside assistanceComplete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, th

FUEL PUMP SHUT-OFF SWITCHFUELRESETThis device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 Mini relay Accessory delay #12 — Not used3

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description17 10A Restraint Control Module (RCM),Passenger Occupant DetectionSystem (P

The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 — Not used2 30A* Climate control blower

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription14 30A* Driver seat15 30A* Passenger seat16 30A* Front amplifier (Shaker 500radio)20

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription51 10A** Convertible top52 30A** Rear defroster53 Diode PCM54 20A** Left HID headlamp

Auxiliary relay with HID headlamps1. Left HID headlamp2. Right HID headlamp3. Not usedOn vehicles equipped with HID headlamps, an auxiliary relay box

Seating and Safety Restraints 97Seating 97Safety restraints 103Airbags 118Child restraints 129Tires, Wheels and Loading 144Tire information 144Tire in

Listening to satellite radio (if equipped)1. If the audio system is turned off,press VOL-PUSH to turn the radioon. Turn VOL-PUSH to adjust thevolume.N

Have a flat tire serviced by an authorized dealer in order to preventdamage to the TPMS sensor, refer to Tire Pressure Monitoring System(TPMS) in the

When driving with one of the dissimilar spare tires listed above, do not:• Exceed 50 mph (80 km/h)• Load the vehicle beyond maximum vehicle load ratin

When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to:• Towing a trailer• Driving vehicles equipped with a

1. Block both the front and rear ofthe wheel diagonally opposite theflat tire. For example, if the leftfront tire is flat, block the right rearwheel.2

4. Put the jack in the jack notchnext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is completely off theground.Never use

TEMPORARY MOBILITY KIT (IF EQUIPPED)Your vehicle may be equipped with a temporary mobility kit (located inthe spare tire well in the trunk). The tempo

• Do not drive farther than 120 miles (200 km). Drive only to theclosest authorized dealer or tire dealer.• Drive carefully and avoid abrupt steering

What to do when a tire is puncturedA tire puncture within the tire’s tread area can be repaired in two stageswith the temporary mobility kit:• In the

4. Loosen the safety latch (4) onthe sealing compound container (5)and rotate the container until it isupright and clicks into place.5. Peel the speed

Note: When the sealing compoundis first added into the tire, the airpressure gauge reading (7) on thecompressor unit may increase up to90 psi; this is

For a single CD system, if a discis not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the

Second stage: Checking tire pressure1. Stop driving after approximately two miles. Then check the airpressure of the damaged tire as follows:• Ensure

2. If the air pressure reads 19 psi (131 kPa) or higher, switch the aircompressor on by pressing the “I” side of the orange button and adjustthe air p

4. Insert the electrical plug into the vehicle’s power point.5. Start the engine (only if the vehicle is outdoors or in awell-ventilated area) to prev

JUMP STARTINGThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury orvehicle da

Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex

Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

Emergency TowingIn case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport veh

Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random pl

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio

ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro

To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent qu

AM/FM stereo / single CD/MP3 sound system (if equipped)Driving while distracted can result in loss of vehicle control,accident and injury. Ford strong

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

4.6L 3V SOHC V8 ENGINEPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your aut

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32-A),available from your au

• Do not use household or glass cleaners as these may damage thefinish of the instrument panel, interior trim and cluster lens.Do not use chemical sol

On vehicles equipped with seat-mounted airbags, do not usechemical solvents or strong detergents. Such products couldcontaminate the side-airbag syste

FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

Working with the engine on• Automatic transmission:1. Set the parking brake and shift to P (Park).2. Block the wheels.• Manual transmission:1. Set the

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.0L SOHC V6 engine1. Battery2. Engine oil filler cap3. Engine oil dipstick4. Brake fluid reservoir5.

4.6L 3V SOHC V8 engineSome vehicles may be equipped with an engine cover.1. Battery2. Engine oil filler cap3. Engine oil dipstick4. Brake fluid reserv

3. Menu: Press to cycle through thefollowing modes:BASS: Press/ / SEEK, SEEK to adjust the bass setting.Press OK to close and return to the main menu.

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas

• 4.0L V6 engine• 4.6L 3V V8 engine6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil level is between the lower

• 4.0L V6 engine• 4.6L 3V SOHC V8 engine• Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an autho

2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler cap

that does not meet Ford material and design specifications, start-upengine noises or knock may be experienced.It is recommended you use the appropriat

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyeswhen working near

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO

Setting the clock: Press MENU until SELECT HOUR or SELECTMINUTE is displayed. Use/ to manually increase/decrease. PressMENU again to disengage clock m

Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant couldmake it difficult to see through

To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. Thecooling system is under press

Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut

What you should know about fail-safe cooling (4.6L V8 engineonly)If the engine coolant supply is depleted, this feature allows the vehicle tobe driven

4. Check the coolant level and replenish if low.Never remove the coolant reservoir cap while the engine isrunning or hot.5. Restart the engine and tak

Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforerefueling your vehicle.• Al

RefuelingFuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others:• Read and follow all the instr

At the next opportunity, safely pull off of the road, remove the fuel fillercap, align the cap properly and reinstall it. The check fuel caplightor “c

Your vehicle was not designed to use fuel or fuel additives with metalliccompounds, including manganese-based additives. Studies indicate thatthese ad

Gasolines that meet the World-Wide Fuel Charter should be used whenavailable. Ask your fuel supplier about gasolines that meet theWorld-Wide Fuel Char

6. / OK(Play/Pause): Thiscontrol is operational in CD/MP3mode. When a CD/MP3 is playing,press to pause or resume play. The CD status will display in t

The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fu

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fuelecon

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled mainten

• Do not turn off the ignition while your vehicle is moving, especially athigh speeds.• Have the items listed in scheduled maintenance informationperf

On board diagnostics (OBD-II)Your vehicle is equipped with a computer that monitors the engine’semission control system. This system is commonly known

Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect

POWER STEERING FLUIDCheck the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules.1. Start the engine and l

BRAKE/CLUTCH FLUIDBrake and clutch systems are supplied from the same reservoir.The fluid level will drop slowly asthe brakes wear, and will rise when

Use of a non-approved automatic transmission fluid may causeinternal transmission component damage and void the warranty.Do not use supplemental trans

• Fill level for V6• Fill level for V84. Add enough fluid through the filler opening to bring the fluid up tothe recommended levels.5. Install and tig

14. AM/FM: Press to select AM/FMfrequency band.15. ON/OFF/Volume: Press to turnON/OFF. Turn to increase/decreasevolume.If the volume is set above a ce

Changing the air filter element (except Bullitt™* Mustang)1. Release the clamps that securethe air filter housing cover.2. Carefully separate the two

MOTORCRAFT PART NUMBERSComponent 4.0L V6 engine 4.6L V8 engineAir filter element FA-1773 FA-1773 (Bullitt™*Mustang uses FA-1891)Fuel filter FG-1083 FG

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord part name orequivalentFord part number /Ford SpecificationBrake fluid and (clutchfl

Item CapacityFord part name orequivalentFord part number /Ford SpecificationEngine oil (4.6L engine) 6.0 quarts (5.7 L)Motorcraft SAE 5W-20Premium Syn

Item CapacityFord part name orequivalentFord part number /Ford SpecificationWindshield washer fluid 4.0 quarts (3.8L)Motorcraft PremiumWindshield Wash

ENGINE DATAEngine 4.0L V6 engine 4.6L V8 engineCubic inches 245 281Required fuel 87 octane 87 octane2Firing order 1-4-2-5-3-6 1-3-7-2-6-5-4-8Ignition

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

LifestyleAsh cup / smoker’s packageCargo organization and managementPeace of mindFull vehicle coversMobile-Ease™ hands-free communication systemRemote

SHAKER 500 — Audiophile In-Dash Six CD/MP3 Sound System(if equipped)2008 05+ Mustang (197)Owners Guide (post-2002-fmt)USA (fus)Entertainment Systems28

AAccessory delay ...63Air cleaner filter ...269–271Airbag supplemental restraintsystem ...

wiper blades ...231Clock ...28Clock adjust6-CD in dash ...

Floor mats ...81Fluid capacities ...272Foglamps ...48Fuel ...

daytime running light ...49fog lamps ...48headlamps ...48headlamps, flash to

Safety belts (see Safetyrestraints) ...103, 107–111Safety Canopy ...126Safety defects, reporting ..226–227Safet

Turn signal ...51VVehicle Identification Number(VIN) ...276Vehicle loading ...

SHAKER 1000 — Audiophile In-dash Six CD/MP3 Sound System(if equipped)2008 05+ Mustang (197)Owners Guide (post-2002-fmt)USA (fus)Entertainment Systems2

Maintenance and Specifications 236Engine compartment 238Engine oil 241Battery 246Engine coolant 248Fuel information 254Air filter(s) 269Part numbers 2

Driving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recommends that drivers useextreme caution when usin

SATELLITE RADIO MENU (if equipped): Press MENU when satelliteradio mode is active to access. Press OK to enter into the satellite radiomenu. Press/ to

• ENABLE ALERTS / DISABLE ALERTS: Press OK to enable/disablethe satellite alert status which alerts you when your selected songs areplaying on a satel

OCCUPANCY mode: Use / select and optimize sound for ALLSEATS, DRIVERS SEAT, REAR SEATS or CONVERTIBLE (if equipped).SPEEDVOL (Speed sensitive volume):

5. SEEK: In radio and CD/MP3mode, press to access the previous() or next ( ) strong stationor track.In satellite radio mode (if equipped), pressSEEK t

12. Memory presets: To set astation, select the desired frequencyband, AM, FM1 or FM2. Tune to thedesired station. Press and hold a preset button unti

16. CD: Press to enter CD/MP3mode. If a CD/MP3 is already loadedinto the system, CD play will beginwhere it ended last.17. LOAD: Press to begin the CD

To play your portable music player using the auxiliary input jack:1. Begin with the vehicle parked and the radio turned off.2. Ensure that the battery

5. For safety reasons, connecting or adjusting the settings on yourportable music player should not be attempted while the vehicle ismoving. Also, the

Don’t:• Expose discs to direct sunlight or heat sources for extended periodsof time.• Insert more than one disc into each slot of the CD changer magaz

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m

Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The

MANUAL HEATING AND AIR CONDITIONING SYSTEM1. Temperature selection: Controls the temperature of the airflow inthe vehicle.2. Mode selections: Controls

4. Passenger heated seat: Press to activate or deactivate thepassenger side heated seat. The passenger heated seat will turn offautomatically after 10

For maximum cooling performance in panel or panel/floor modes:1. Move temperature control to the coolest setting.2. Select A/C and recirculated air ()

CABIN AIR FILTERYour vehicle is equipped with a cabin air filter, which is located just infront of the windshield under the cowl grille on the passeng

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Fog la

Flash to passPull toward you, to the first detent,to activate and release to deactivate.Note: Vehicles equipped with HIDheadlamps will hear an audible

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident the alignment of yo

6. Locate the vertical adjuster oneach headlamp, then usea7mmAllen wrench or a Phillipsscrewdriver to adjust the headlampup or down.7. HORIZONTAL AIM

Ambient/Mood lighting (if equipped)Illuminates 4 footwells and 2cupholders with a choice of 7 colors.The ambient lighting control switchis located on

Function Trade NumberHeadlamp H13* HID (high intensity discharge) headlamp (ifequipped)D3RPark lamp, turn lamp, side marker (front) 3157 or 3157KSidem

2. Disconnect the electricalconnector from the bulb bydepressing the retainer clip andpulling rearward.3. Remove the bulb by rotating itcounterclockwi

Replacing front parking lamp bulbs1. Make sure the headlamp control is in the off position and open thehood.2. Locate the lamp assembly fromunderneath

1. Make sure headlamp switch is inthe off position, then open thetrunk.2. Carefully remove fastenersaround the lamp area and thenremove the interior t

6. Pull the bulb straight from thesocket.Install the new bulb in reverseorder.Replacing rear sidemarker lamp bulbs1. Make sure the headlamp switch isi

4. Carefully pull the bulb straightout of socket.Install the new bulb in reverseorder.Replacing license plate lamp bulbs1. Make sure the headlamp swit

MULTI-FUNCTION LEVERWindshield wiper: For intermittentoperation, move control up oneposition.Adjust the rotary control to thedesired speed setting.For

Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Airbag supplemental re

Note: Do not operate the washer when the washer reservoir is empty.This may cause the washer pump to overheat. Check the washer fluidlevel frequently.

AUXILIARY POWER POINT (12VDC)Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will damag

POWER WINDOWSDo not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injurethemselves.W

Restoring the Express up functionality (Front windows only)Under low battery power conditions, Express Up only functionality maybe lost. To reset this

the window until it completes its travel and hold the switch down for 2seconds. Immediately after releasing the window down switch, pull theswitch up

Electronic compass (if equipped)The compass reading will remain accurate during most drivingconditions. The compass is continuously re-calibrating due

5. Repeatedly press until your zone number is shown in the mirrordisplay, then release.6. The display will show all segments, then return to normal co

Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas

• Press and release the SET + control to operate the Tap-Up function.Each tap will increase the set speed by 1 mph (1.6 km/h).• Use the accelerator pe

To lower the convertible top:1. Bring vehicle to a complete stop. Key must be in the ON position. It isrecommended that the vehicle’s engine is runnin

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access e

Installation of the boot (if equipped)Be sure the boot is secure on the vehicle before driving.1. Install the boot on the vehicle by hooking the boot

Storing the boot1. Position the boot right-side up and fold each side of the boot inward.2. Turn the boot upside down and fold the left side of the bo

To raise the convertible top:1. Bring the vehicle to a complete stop. Key must be in the ON position.It is recommended that the vehicle’s engine is ru

MESSAGE CENTER (IF EQUIPPED)With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle info

Pressing the RESET control cycles the message center through each ofthe systems being monitored.The sequence of the system check report and how it app

Adjusting MyColor™: MyColor™ is a user defined backlighting color.The backlighting colors are achieved through the blending of light fromRed, Green, a

2. Pressing the RESET controlcycles the message center througheach of the language choices.3. Press and hold the RESETcontrol to set the language choi

Dual mode displayThe DTE function will display LOW FUEL LEVEL and sound a tone forone second when you have approximately 50 miles (80 km) to empty. If

Instantaneous fuel economySelect this function from the INFOmenu to display your instantaneousfuel economy. This will display yourfuel economy as a Ba

System warningsSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems.In the event of a multiple warning si

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

DRIVER’S DOOR AJAR. Displayed when the driver’s door is notcompletely closed.PASSENGER DOOR AJAR. Displayed when the passenger side door isnot complet

TIRE PRESSURE SENSOR FAULT. Displayed when a tire pressuresensor is malfunctioning, or your spare tire is in use. For moreinformation on how the syste

KEYSOne key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency.Your keys are programmed to your v

Smart locksThis feature helps prevent you from locking yourself out of the vehicle ifyour key is still in the ignition.When you open the driver’s door

Autolock (if equipped)On vehicles equipped with an automatic transmission, this featureautomatically locks all vehicle doors when:• all doors are clos

Adults are advised to familiarize themselves with the operation andlocation of the release handle.To open the luggage compartmentdoor (lid) from withi

REMOTE ENTRY SYSTEMThis device complies with part 15 of the FCC rules and with RSS-210 ofIndustry Canada. Operation is subject to the following two co

Locking the doors1. Press and release to lock all the doors. Note: The interior lampswill turn off (unless the dome lamp control is in the full-up pos

Replacing the batteryThe remote entry transmitter uses one coin type three-volt lithiumbattery CR2032 or equivalent.To replace the battery:1. Twist a

Replacing lost remote entry transmittersIf you would like to have your remote entry transmitter reprogrammedbecause you lost one, or would like to buy

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

The dome lamp control must not be set to the off position for theilluminated entry system to operate.The inside lights will not turn off if:• they hav

3. Turn the ignition to the 3 (ON) position; the horn will chirp toindicate the driver configuration mode has been activated.Activating or deactivatin

Anti-theft indicatorThe anti-theft indicator is located inthe instrument cluster.• When the ignition is in the 1 (OFF/LOCK) position, the indicator wi

Replacement keysIf your keys are lost or stolen and you don’t have an extra coded key,you will need to have your vehicle towed to an authorized dealer

6. Turn the ignition to the 1 (OFF/LOCK) position, and remove thesecond key from the ignition.7. Within twenty seconds of removing the previously prog

driver door key cylinder, the system will monitor the doors,trunk, and hood but the motion sensing and vehicle inclinesensing will not arm.Do not arm

Disarming the systemYou can disarm the active anti-theft system by any of the followingactions:• Unlock the doors by using the remote entry transmitte

SEATINGReclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a colli

Lift the head restraint to raise theheight.To lower the head restraint, pressthe button located on the driver’sside post, and push down on thehead res

Pull lever up to adjust the angle ofthe seatback.Four-way seat adjust (driver side only)Pump the handle upwards to raisethe cushion and pump downward