Ford 2008 F-550 v.3 Manuel d'utilisateur

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 19Entertainment Systems 23AM/FM stereo 23AM/FM stereo with CD 25AM/FM stereo wit

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

TILT STEERING WHEEL (IF EQUIPPED)1. Pull and hold the steering wheelrelease control toward you.2. Move the steering up or downuntil you find the desir

ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamp.OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehic

The auxiliary power point is locatedon the instrument panel.On SuperCab and Crew Cab models, another power point is locatedon the rear of the center c

When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not inthe proximity of the win

Power rear slider window (if equipped)Do not leave children unattended in the vehicle and do not letchildren play with the power windows. They may ser

The mirror will automatically return to the normal state whenever thevehicle is placed in R (Reverse) (when the mirror is on) to ensure abright clear

Fold-away mirrorsFold the side mirrors in carefully before driving through a narrow space,like an automatic car wash.Powerfold mirrorsIf equipped with

the full travel may cause the system to disable the fold/unfold function toprotect the motors from overheating. Should this occur, waitapproximately 3

travel is reached, it is normal to hear the power telescoping motorsrunning as long as you continue to hold the switch.• To telescope the mirrors inbo

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is

Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas

Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed.Increasing spee

Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal. This will not erase your vehicle’s previouslyset

In AM, FM1, or FM2 mode:• PressSEEK toselect preset stations within theselected radio band or press andhold to select the next/previousradio frequency

Press FAN + or - to adjust fanspeed.UPFITTER CONTROLS (IF EQUIPPED)Your vehicle may be equipped withthe Upfitter option package whichwill provide four

The relays are coded as shown inthe accompanying illustration.There will also be one power leadfor each switch found as a blunt-cutand sealed wire loc

ONE-TOUCH MOON ROOF (IF EQUIPPED)The moon roof control is located on the overhead console.Note: The moon roof will open tothe “comfort” position first

HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED)The HomeLink威 Wireless ControlSystem, located on the driver’s visor,provides a convenient way toreplace

1. Position the end of yourhand-held transmitter 1–3 inches(2–8 cm) away from the HomeLink威button you wish to program (locatedon your visor) while kee

WARNING LIGHTS AND CHIMESVehicles equipped with a manual transmissionVehicles equipped with an automatic transmission2008 F-250/350/450/550 (f23)Owner

Gate Operator & Canadian ProgrammingDuring programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time for

Erasing HomeLink姞 buttonsTo erase the three programmedbuttons (individual buttons cannotbe erased):• Press and hold the two outerHomeLink威 buttons unt

• Rear cupholders (Crew Cab only)Use only soft cups in the cupholder. Hard objects can injure youin a collision.STANDARD MESSAGE CENTERWith the igniti

Distance to empty (DTE)Selecting this function from theINFO MENU estimatesapproximately how far you can drivewith the fuel remaining in your tankunder

Setup menuPress and hold the SELECT/RESETcontrol switch to get into theSETUP MENU sequence from theINFO MENU for the followingdisplays:• Units (Englis

System checkPress and hold the SELECT/RESET control switch to select SYSTEMCHECK when HOLD RESET FOR SYSTEM CHECK is displayed in themessage center. S

Warning display StatusPark brake engaged Warning returns after 10 minutes ifcondition still exists.Check brake systemDriver door ajar Warning returns

PASSENGER DOOR AJAR Displayed when the passenger’s door is notcompletely closed.REAR LEFT DOOR AJAR Displayed when the rear left door is notcompletely

may or may not restart after cycling the ignition OFF. If the vehiclerestarts, there may be limited power, or there could be full function. Ifthe exha

OPTIONAL MESSAGE CENTER (IF EQUIPPED)With the ignition in the RUNposition, the message center,located on your instrument cluster,displays important ve

Harley-Davidson vehiclesWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A war

Info menuThis control displays the followingcontrol displays:• Trip Odometer A or B• Distance to Empty• Average Fuel Economy• Drive Time (Elapsed Trav

Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in miles/gallon or liters/100 km.If you calculate

Setup menuPress this control for the followingdisplays:• System Check• Units (English/Metric)• Autolamp Timer Presets (ifequipped)• Autolock On/Off (i

3. AIR FILTER (Diesel engine only)4. DOOR AJAR5. BRAKE SYSTEM6. FUEL LEVELUnits (English/Metric)1. Select this function from theSETUP menu for the cur

Usually, when something affects the compass readings, the compass willcorrect itself after a few days of operating your vehicle in normalconditions. I

7. Press the RESET control to startthe compass calibration function.8. Slowly drive the vehicle in acircle (less than 3 mph [5 km/h])until the CIRCLE

Warning messages that have been reset are divided into two categories:• They will reappear on the display ten minutes from the reset.• They will not r

DRIVER DOOR AJAR Displayed when the driver’s door is notcompletely closed.PASSENGER DOOR AJAR Displayed when the passenger’s door is notcompletely clo

shutdown when the vehicle speed is below 3 mph (5 km/h). Stop thevehicle as soon as safely possible and contact your authorized dealer.Depending on th

TAILGATE LOCK (IF EQUIPPED)Your vehicle may be equipped with atailgate lock designed to helpprevent theft of the tailgate.• Insert ignition key and tu

Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interiorfloor coverings or other

10. Pull left-hand hinge straight to the right to disengage the left-handtailgate hinge socket from the left-hand box pivot post.11. Lift left side of

2. Slide the latch at the bottom of the handle, then lower the handle.Note:• Fully close and latch the tailgate step before moving the vehicle.• Never

3. Rotate the panels toward thetailgate.Repeat Steps 1–3 for the other side of the bed extender.4. Connect the two panels, then rotate both knobs a qu

Note: When the vehicle is in motion, ensure the locking pins and knobsare fully engaged.Note: Ensure all cargo is secured.Note: When the vehicle is in

KEYSThe key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency.If

• the ignition is in the 3 (ON) position,• you shift into any gear putting the vehicle in motion, and• the vehicle attains a speed greater than 12 mph

6. To enable/disable the autolock feature, press the unlock control, thenpress the lock control. The horn will chirp once if autolock wasdeactivated o

Power door lock switch autounlock enable/disable procedureBefore starting, ensure the ignition is in the 1 (OFF/LOCK) position andall vehicle doors ar

CHILDPROOF DOOR LOCKS (IF EQUIPPED)• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the ou

• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta key.• activate the personal alarm.If there are problems with the remote

Safety belt: Reminds you to fastenyour safety belt. A BeltMinder威chime will also sound to remind youto fasten your safety belt. Refer tothe Seating an

2. Press and release again within three seconds to confirm that allthe doors are closed and locked. Note: The doors will lock again, thehorn will chir

Deactivating the memory seat featureTo deactivate this feature:1. Press the SET control on the driver’s door panel.2. Within five seconds, press any c

Note: Replacement of the battery will not cause the remote transmitterto become deprogrammed from your vehicle. The remote transmittershould operate n

6. Turn the ignition to the 1 (OFF/LOCK) position after you havefinished programming all of the remote entry transmitters. Note: After20 seconds, you

2. Press the power door unlockcontrol on the door panel threetimes.3. Turn the ignition from the 3 (ON)position to the 1 (OFF/LOCK)position.4. Press t

KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to lock or unlock the doorswithout using a key.The keypad can be operated withth

3. Press and hold the 1 • 2 for two seconds. This must be done withinfive seconds of completing Step 2.Your personal code is now erased and only the f

Note: Large metallic objects, electronic devices that are used topurchase gasoline or similar items, or a second coded key on the samekey chain may ca

Replacement keysIf your keys are lost or stolen and you don’t have an extra coded key,you will need to have your vehicle towed to an authorized dealer

5. Within 10 seconds of removing the second coded key, insert the newunprogrammed key (new key/valet key) into the ignition and turn theignition from

If the light remains on, have the system serviced immediately by yourauthorized dealer. Refer to Traction control in the Driving chapter formore infor

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

Full bench seat (if equipped)• Lift the release bar to move theseat forward or backward. Ensurethat the seat is relatched intoplace.• Pull up on the l

40/20/40 front seat armrest and console (if equipped)To release the armrest, pull forwardon the strap and pull the armrestdown.To gain access to the s

Captain’s chair (if equipped)• Lift the bar to move the seatforward or rearward. Make surethat the seat is relatched intoplace.• To recline the seatba

Press front to raise or lower thefront portion of the seat cushion.Press rear to raise or lower the rearportion of the seat cushion.Press the control

Persons who are unable to feel pain to the skin because ofadvanced age, chronic illness, diabetes, spinal cord injury,medication, alcohol use, exhaust

A memory seat position may be programmed at any time.The memory positions are also recalled when you press your remoteentry transmitter UNLOCK control

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped underneath theseatback. After returning the

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.All

Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until

Four wheel drive low (ifequipped): Illuminates whenfour-wheel drive low is engaged.Four wheel drive high (ifequipped): Illuminates whenfour-wheel driv

This mode should be used any time a child safety seat is installedexcept a booster in a front or rear outboard passenger seating position(if equipped)

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe seat belt assembly “automatic locking retractor” feature orany other seat belt function is not oper

Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could re

2. Insert the belt into the clip on theback panel. Protect the stowed beltif you carry cargo this may damageor soil the belt.If the belt has been disc

longer. The cinch tongue is designed to slip during a crash, so alwayswear the shoulder belt properly and don’t allow any slack in either thelap or sh

Lap beltsAdjusting the lap beltThe lap belt should fit snugly and as low as possible around thehips, not across the waist.• 1st row center seating pos

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war

If... Then...The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition...The Belt-Minder威 feature will notactivate.The

Reasons given... Consider...“The people I’m with don’twear belts”Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE peop

• the driver’s safety belt is unbuckled• the parklamps/headlamps are in the OFF position (If the vehicle isequipped with Autolamps, this will not affe

• Low oil pressureKey-in-ignition warning chime: Sounds when the key is left in theignition in the OFF, LOCK or ACCESSORY position and the driver’s do

Safety belt extension assemblyIf the safety belt is too short when fully extended, there is a 8 inch(20 cm) safety belt extension assembly that can be

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

Never place your arm over the air bag module as a deploying airbag can result in serious arm fractures or other injuries.To properly position yourself

An infant in a rear-facing seat faces a high risk of serious or fatalinjuries from a deploying passenger airbag. Rear facing infantseats should NEVER

restrained or are otherwise out of position at the time of airbagdeployment. Thus, it is extremely important that occupants be properlyrestrained as f

Disposal of airbags and airbag equipped vehiclesSee your local authorized dealer. Airbags MUST BE disposed of byqualified personnel.Passenger airbag O

An infant in a rear-facing seat faces a high risk of serious or fatalinjuries from a deploying passenger airbag. Rear facing infantseats should NEVER

If your vehicle has rear seats, always transport children who are12 and younger in the rear seat. Always use safety belts andchild restraints properly

• the child has a medical condition which, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the dr

• the child has a medical condition that, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the dri

GAUGESSpeedometer: Indicates the current vehicle speed.Standard instrument clusterHarley-Davidson instrumentcluster2008 F-250/350/450/550 (f23)Owners

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.Alwa

When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the

• Those with a high back.If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo

Follow all instructions provided by the manufacturer of thebooster seat.Never put the shoulder belt under a child’s arm or behind theback because it e

• Top tether anchors can be used for children up to 60 pounds (27 kg)in a child restraint, and to provide upper torso restraint for childrenup to 80 p

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a c

Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a

• F-Series Crew CabTether strap attachment1. Position the child safety seat on the seat cushion.2. Route the child safety seat tether strap over the b

• Front seat (SuperCab)• Rear seats (Crew Cab)If the tether strap is clipped incorrectly, the child safety seatmay not be retained properly in the eve

Locks and Security 144Keys 144Locks 144Anti-theft system 156Seating and Safety Restraints 160Seating 160Safety restraints 167Airbags 181Child restrain

Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature, the needle will be inthe normal range (between “

Many tether straps cannot be tightened if the tether strap is hooked tothe loop directly behind the child seat. To provide a tight tether strap:1. Rou

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary.

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air

Maximum Permissible Inflation Pressure is the tire manufacturer’smaximum permissible pressure and/or the pressure at which themaximum load can be carr

Matching Spare Tire/Wheel Information sections for descriptions):Store and maintain at the higher of the front and rear inflation pressureas shown on

Stay out of the trajectory (1) as indicated in the illustration.TIRE CAREInspecting your tiresPeriodically inspect the tire treads for uneven or exces

Standard instrument clusterHarley-Davidson instrumentclusterEngine oil pressure gauge:Indicates engine oil pressure. Theneedle should stay in the norm

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them

U.S. DOT Tire Identification Number (TIN)U.S. and Canada Federal regulations require tire manufacturers to placestandardized information on the sidewa

When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of thetire to set the beads without ad

• Do not run over curbs or hit the tire against a curb when parkingIf your vehicle is stuck in snow, mud, sand, etc., do not rapidlyspin the tires; sp

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive (4WD)(front tires at top of diagram)Sometimes irregular tire wear can be corrected by rotating the t

• Dual Rear Wheel (DRW) – Sixtire rotationIf your vehicle is equipped with dualrear wheels it is recommended thatthe front and rear tires (in pairs) b

INFORMATION CONTAINED ON THE TIRE SIDEWALLU.S. and Canada Federal regulations require tire manufacturers to placestandardized information on the sidew

7. H: Indicates the tire’s speed rating. The speed rating denotes thespeed at which a tire is designed to be driven for extended periods oftime under

10. Tire Ply Composition and Material Used: Indicates the number ofplies or the number of layers of rubber-coated fabric in the tire tread andsidewall

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Battery voltage gauge (manualtransmission only): Indicates thebattery voltage when the ignition isin the RUN position. If the pointermoves and stays o

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including inter

When your temporary spare tire is installedWhen one of your road tires needs to be replaced with the temporaryspare, the TPMS system will continue to

Low Tire PressureWarning LightPossible cause Customer Action RequiredSolid Warning Light Tire(s)under-inflated1. Check your tire pressure toensure tir

Low Tire PressureWarning LightPossible cause Customer Action RequiredFlashing WarningLightSpare tire in use Your temporary spare tire is inuse. Repair

TPMS reset procedure (if applicable)This procedure is only required after tire rotation on vehicleswith different front and rear tire pressures.To det

TPMS reset toolA special TPMS reset tool has been provided with your vehicle to resetyour TPMS after tire rotation. The tool is located with your Owne

3. Press and hold the brake pedal for two (2) seconds, then release.4. Turn the ignition to OFF/LOCK (DO NOT remove the key.)5. Cycle the ignition fro

1. Left front tire: Place the TPMS reset tool against the left front tirewhere the tire meets the rim, opposite from the valve stem (1) as shown.This

AUDIO SYSTEMSAM/FM stereo system (if equipped)Driving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recomm

Rotation, pressure adjustment and TPMS reset exampleThe following example describes all the major steps involved in rotatingtires on a vehicle with di

Sensor position following tirerotationSensor 1: 50 psiSensor 2: 50 psiSensor 3: 80 psiSensor 4: 80 psiPressure adjustment without therequired TPMS res

Rotation, pressure adjustmentand successful completion of theTPMS reset procedureSensor 1: 80 psiSensor 2: 80 psiSensor 3: 50 psiSensor 4: 50 psiTire

VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).

Tongue Load or Fifth Wheel King Pin Weight – refers to the amountof the weight that a trailer pushes down on a trailer hitch.Examples: For a 5,000 lb.

The following gives you a few examples on how to calculate the availableamount of cargo and luggage load capacity:• Another example for your vehicle w

2. AUDIO: Press AUDIO repeatedlyto gain access to the followingsettings:TREB (Treble): Press AUDIO to reach the treble setting.Use/ / SEEK .BASS (Bass

Loaded vehicles may handle differently than unloaded vehicles.Extra precautions, such as slower speeds and increased stoppingdistance, should be taken

Note: Do not exceed the GCWR listed for your vehicle on the followingchart/table, or the GVWR, GAWR or tire ratings specified on the TireLabel or Safe

Maximum GCWR - lb. (kg.)Engine Rear axleratioManualtransmissionAutomatictransmissionF–350 Dual Rear Wheel (DRW) Chassis Cab5.4L 3.73 15000 (6804) 1650

Hitch TypeMaximumGrossTrailer Weight— lb. (kg)MaximumTongue Weight— lb. (kg)6.8L DRWPickup2.5” ID withoutadapter(requires2.5” drawbar)Weight carrying

Note: Adjusting a weight distributing hitch so the rear bumper of thevehicle is higher than it was unloaded will defeat the function of theweight dist

The TBC user interface consists ofthe following:1. +/- (GAIN adjustmentbuttons): Pressing these buttonswill adjust the TBC’s power outputto the traile

the Center High-Mount Stop Lamp (presuming proper trailer electricalconnection). Pressing the vehicle brake pedal will also illuminate bothtrailer and

TRAILER DISCONNECTED (if equipped with message center) orCHECK TRAILER (if equipped with mini message center): Thismessage is displayed when a trailer

• The TBC interacts with the brake system of the vehicle, includingABS, in order to reduce the likelihood of trailer wheel lockup.Therefore, if these

• Do not exceed the GCWR rating or transmission damage may occur.• Your vehicle may be equipped with a temporary or conventional sparetire. If the spa

AM/FM stereo single CD/satellite compatible sound system(if equipped)Driving while distracted can result in loss of vehicle control,accident and injur

• Trailer loads should be evenly distributed front to back and left toright.• The load distribution within the trailer should be such that 10%–15%of t

Exceeding these limits may allow water to enter critical vehiclecomponents, adversely affecting driveability, emissions and reliability.Replace front

STARTINGPositions of the ignition1. OFF/LOCK, shuts off the engineand all accessories/locks the steeringwheel, gearshift lever and allows keyremoval.2

If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf

If starting a vehicle with a manualtransmission:1. Make sure the parking brake isset.2. Push the clutch pedal to the floor.• Turn the key to 3 (ON) wi

If your vehicle has an automatic transmission, it will have acomputer assisted cranking system. This feature assists in starting theengine. If the ign

outdoors, in cold temperatures, and is clearly marked ⬙Suitable for Usewith Outdoor Appliances.⬙ Never use an indoor extension cordoutdoors; it could

Make sure system is unplugged and properly stowed before driving thevehicle. While not in use, make sure the protective cover seals theprongs of the e

effectiveness of the ABS and will increase your vehicle’s stoppingdistance. The ABS will be activated immediately, allowing you to retainfull steering

If you’re parking your vehicle on a grade or with a trailer, press and holdthe brake pedal down, then set the parking brake. There may be a littlevehi

2. (Phone): Pressing(Phone) results in “NO PHONE”message shown in display.3. MENU: Press MENU repeatedlyto access to the following settings:Setting th

The Traction Control™ switch,located on the instrument panel tothe left of the climate controlsystem, has an indicator light thatilluminates when the

• improper steering alignmentIf any steering components are serviced or replaced, install newfasteners (many are coated with thread adhesive or have p

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED)Brake-shift interlockThis vehicle is equipped with a brake-shift interlock feature that preventsthe gear

Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position andremove the key wheneve

Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position andremove the key wheneve

When you shut-off and restart the engine, the transmission willautomatically return to normal D (Overdrive) mode (Tow/Haul OFF).Do not use the Tow/Hau

MANUAL TRANSMISSION OPERATION (IF EQUIPPED)Using the clutchThe manual transmission has a starter interlock that prevents crankingthe engine unless the

Shift according to the following shift speed charts:Upshifts when accelerating(recommended for best fuel economy)6-speed transmissionShift from: Trans

3. Turn the ignition off.Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake

The RSS detects obstacles up to6 feet (2 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the fi

CANT SAVE will appear in the display.) When the chosen song isplaying on any satellite radio channel, the system will alert you withan audible prompt.

If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement

Objects in the red zone are closest to your vehicle and objects in thegreen zone are further away. Objects are getting closer to your vehicle asthey m

Nighttime and dark area useAt night time or in dark areas, the reverse camera system relies on thereverse lamp lighting to produce an image. Therefore

Manual Shift On Stop (MSOS) 4x4 system (if equipped)The 4WD system is engaged ordisengaged by rotating the controlfor both front wheel hub locks fromt

• auto-manual hub locks can bemanually overridden by rotatingthe hub lock control from AUTOto LOCK if desired.• automatic operation of thehub locks is

4H (4x4 High) – For winter and off-road conditions. Sends power tofront and rear wheels. This mode is not intended for use on drypavement.N (Neutral)

Shifting from 4H (4x4 High) to 4L (4x4 Low)1. Bring the vehicle to a stop or a speed below 5 mph (8 km/h).2. Place the gearshift lever in N (Neutral).

This position should only be usedwhen towing the vehicle.Do not leave the vehicle unattended with the transfer case in theN (Neutral) position. Always

• Do not shift into 4x4 HIGH with the rear wheels slipping.Shifting from 4x4 HIGH to 2WDRotate the 4x4 control to 2WD atany forward speed. Disengageme

3. Move the 4x4 control to the 4x4HIGH or 2WD position.4. Hold the shift conditions until the4x4 LOW indicator light shuts off.5. If the 4x4 LOW indic

BASS: Press MENU to reach the bass setting.Use/ / SEEK, SEEK to adjust.TREB (Treble): Press MENU to reach the treble setting.Use/ / SEEK, SEEK to adju

Basic operating principles• Do not use 4WD on dry, hard surfaced roads. Doing so will produceexcessive noise, increase tire wear and may damage drive

Do not rock the vehicle for more than a few minutes or damageto the transmission and tires may occur or the engine mayoverheat.Do not spin the wheels

the driveline. Therefore, the vehicle is free to roll even if the automatictransmission is in P (Park) or the manual transmission is in gear. Do notle

Note: If air is released from your tires, the Tire Pressure MonitoringSystem (TPMS) indicator light may illuminate (if equipped).Mud and waterIf you m

Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should

Should you start to slide while driving on snowy or icy roads, turn thesteering wheel in the direction of the slide until you regain control.Avoid sud

VEHICLE USED AS A STATIONARY POWER SOURCEAuxiliary equipment called power take-off, or PTO, is often added to theengine or transmission to operate uti

SNOWPLOWINGFord recommends that the Super Duty F-Series used for snow removalinclude a snow plow package option.Installing the snowplowWeight limits a

• Snowplowing with vehicles equipped with a diesel engine may result inengine overheating in highway driving with snowplow blade raisedunless equipped

Additional equipment such as snowplow equipment may effectthe performance of the airbag sensors increasing the risk ofinjury. Please refer to the Ford

4. AUX: Press repeatedly to cyclethrough FES/DVD (if equipped),LINE IN (auxiliary audio mode, ifequipped) and SAT1, SAT2 and SAT3 modes (satellite rad

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

Canadian customers refer to your Customer Information Guidefor information on:• coverage period• exact fuel amounts• towing of your disabled vehicle•

HAZARD FLASHERThe hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is

The switch has a red button on topof it.To reset the switch:1. Turn the ignition off.2. Check the fuel system for leaks.3. If no leaks are apparent, r

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

To remove the fuse panel cover, pullthe panel toward you. When theclips of the panel disengage, let thepanel fall easily.To remove a fuse use the fuse

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 30A Not used (spare)2 15A Not used (spare)

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description11 10A Not used12 7.5A Power mirror switch, Driver powerseat (Memory)13 5A

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description33 10A Trailer tow brake controller, Trailertow battery charge relay coil34

Always disconnect the battery before servicing high currentfuses.To reduce risk of electrical shock, always replace the cover tothe Power Distribution

Customer Assistance 325Reporting safety defects (U.S. only) 331Reporting safety defects (Canada only) 332Cleaning 333Maintenance and Specifications 34

current track is finished playing. CD SHUF will appear in the display. Todisengage, press SHUFFLE again. SHUFFLE OFF will appear in thedisplay.Note: I

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription9 40A* ABS module (Coil)10 20A* Cigar lighter11 20A* Instrument panel power point12 1

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription32 20A** Fuel pump relay33 20A** Back-up lamp relay34 25A** Trailer stop/turn relay35

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription54 Relay Starter solenoid55 Relay Trailer tow park lamps56 Relay Trailer tow battery

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription73 2A** Reverse Camera System (RCS)74 20A** Gasoline engines: VPWR:HEGO, CMS, MAFS, E

Dissimilar spare tire/wheel informationFailure to follow these guidelines could result in an increasedrisk of loss of vehicle control, injury or death

3. Full-size dissimilar spare without label on wheelWhen driving with the full-size dissimilar spare tire/wheel, do not:• Exceed 70 mph (113 km/h)• Us

T-type/Mini-spare tire information (Harley-Davidson only)Your vehicle may be equipped with a temporary spare tire. This sparetire is considered “tempo

Park on a level surface, activatehazard flashers and set the parkingbrake.• Automatic transmission: Placegearshift lever in P (Park).• Manual transmis

• one handle extension and twotypical extensions. To assemble,align button with hole and slideparts together. To disconnect,depress button and pull ap

5. Remove the retainer through the center of the wheel.Tire change procedure1. Turn engine off and block thewheel that is diagonally opposite ofthe fl

press again to scroll through the current song title, artist, channelcategory and the SIRIUS long channel name.In TEXT MODE sometimes the display requ

• Front (4x2)• Front driver side (4x4)Note: Make sure the jack fits ontothe flat area on the outboard side ofthe differential.• Front passenger side (

• RearNever use the front or reardifferential as a jacking point.To lessen the risk ofpersonal injury, do not putany part of your body under thevehicl

The following steps apply to F–350 Dual Rear Wheel (DRW) andF–450/F–550 vehicles only:11. Slide the notched end of thejack handle over the release val

• Front passenger side (4x4): F-350DRWNote: View shown from the rear ofthe vehicle to clearly identify thejack point.Note: Place the jack directly und

13. Insert the jack handle into thepump linkage.14. Use an up-and-down motionwith the jack handle to raise thewheel completely off the ground.Hydrauli

10–lug nut torque sequence19. Stow the flat tire. Refer to Stowing the flat/spare tire if the vehicleis equipped with a spare tire carrier.Note: Do no

If the ornament retention towers arealigned between the studs/lug nuts,the ornament is improperlyinstalled. This improper installationmay appear and s

WHEEL LUG NUT TORQUE SPECIFICATIONSOn vehicles equipped with single rear wheels, retighten the lug nuts tothe specified torque at 500 miles (800 km) a

Inspect the wheel pilot hole prior toinstallation. If there is visiblecorrosion in wheel pilot hole,remove loose particles by wipingwith clean rag and

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level.5. Tu

Premium/Audiophile in-dash six CD/MP3/satellite compatible soundsystem (if equipped)Driving while distracted can result in loss of vehicle control,acc

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

Note: Towing a 4x2 or an ESOF 4x4 vehicle with the rear wheels on theground for more than 50 miles (80 km) and/or in excess of 35 mph(56 km/h) may cau

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

Satellite radio is available only with a valid SIRIUS radiosubscription. Check with your authorized dealer for availability.2.(Phone): Press to mute t

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio

ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro

To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

• Remove particles such as bird droppings, tree sap, insect deposits, tarspots and industrial fallout before repairing paint chips.• Always read the i

• 5.4L V8 gasoline engine• 6.8L V10 gasoline enginePLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These produc

• For plastic headlamp lenses, use Motorcraft Ultra Clear Spray GlassCleaner (ZC-23).WINDOWS AND WIPER BLADESThe windshield, rear and side windows and

Do not use chemical solvents or strong detergents when cleaningthe steering wheel or instrument panel to avoid contamination ofthe airbag system.If a

(ZC-53-A), Motorcraft Paint Sealant (ZC-45), or Motorcraft Custom ClearCoat Polish (ZC-8-A). Note: Removal of deep scuffs and scratches shouldbe perfo

• To clean, use a soft cloth with Motorcraft Deluxe Leather and VinylCleaner (ZC-11–A). Dry the area with a soft cloth.• To help maintain its resilien

• SAVE SONG: Press OK to save the currently playing song title in thesystem’s memory. (If you try to save something other than a song,CANT SAVE will a

• Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl or plastics.ScratchesNatural Markings - Be

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTSYour authorized dealer has many quality products available to clean yourvehicle and protect its finishes. T

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a

2. Block the wheels.• Manual transmission:1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral).2. Block the wheels.Note:

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENTRefer to the 6.0 and 6.4 Liter Power Stroke Direct Injection TurboDiesel Owner’s Guide Supplement for

6.8L V10 gasoline engine1. Windshield washer fluid reservoir2. Battery3. Transmission fluid dipstick (automatic transmission)4. Engine oil filler cap5

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

Note: Poor wiper quality can be improved by cleaning the wiper bladesand the windshield; refer to Windows and wiper blades in theCleaning chapter.Note

• If the oil level is below the MINmark, add enough oil to raise thelevel within the MIN-MAX range.• Oil levels above the MAX mark may cause engine da

Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by th

When the six strongest stations are filled, the station stored in preset 1will begin playing. If there are less than six strong stations, the systemwi

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a

If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreco

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “COLD FILL RANGE” in thecoolant re

Note: Use of Motorcraft Cooling System Stop Leak Pellets may darkenthe color of Motorcraft Premium Gold Engine Coolant from yellow togolden tan.• Do n

3. Step back while the pressure releases.4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and re

Severe climatesIf you drive in extremely cold climates (less than –34°F [–36°C ]):• It may be necessary to increase the coolant concentrationabove 50%

How fail-safe cooling worksIf the engine begins to overheat:• The engine coolant temperaturegauge will move to the red (hot)area.• The message center

Driving the vehicle without repairing the engine problemincreases the chance of engine damage. Take your vehicle to aservice facility as soon as possi

Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforerefueling your vehicle.• Al

The default setting is off; increasing your vehicle speed will not changethe volume level.Adjust 1–7: Increasing this setting from 1 (lowest setting)

Use the following guidelines to avoid static build-up when filling anungrounded fuel container:• Place approved fuel container on the ground.• DO NOT

If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The vehicle warranty maybe void for any d

Octane recommendationsYour vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofga

If you have run out of fuel:• You may need to cycle the ignition from OFF to ON several times afterrefueling to allow the fuel system to pump the fuel

• Use the same filling rate setting (low-medium-high) each time thetank is filled.• Allow no more than 2 automatic click-offs when filling.• Always us

• Idling for long periods of time (greater than one minute) may wastefuel.• Anticipate stopping; slowing down may eliminate the need to stop.• Sudden

• Using fuel blended with alcohol may lower fuel economy.• Fuel economy may decrease with lower temperatures during the first8–10 miles (12–16 km) of

emission control, such non-Ford parts should be equivalent to genuineFord Motor Company parts in performance and durability.Do not park, idle, or driv

4. Driving through deep water - the electrical system may be wet.These temporary malfunctions can be corrected by filling the fuel tankwith good quali

POWER STEERING FLUIDCheck the power steering fluid. Refer to the scheduled maintenanceinformation for the service interval schedules. If adding fluid

In TEXT MODE, press SEEK, SEEK to view theprevious/additional display text.In CATEGORY MODE, pressSEEK, SEEK to select a category.Satellite radio is a

BRAKE FLUID• Vacuum boost system• Hydroboost systemThe fluid level will drop slowly as the brakes wear, and will rise when thebrake components are rep

Carefully read cautionary information on product label. ForMEDICAL EMERGENCY INFORMATION, contact a physician orPoison Control Center immediately; on

4. Latch the gearshift lever in P (Park) and leave the engine running.5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. Ifneces

Adjusting automatic transmission fluid levelsBefore adding any fluid, make sure the correct type is used. The type offluid used is normally indicated

3. Fluid level should be at thebottom of the opening.4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the open

Use only fluid that meets Ford specifications. Refer to MaintenanceProduct Specifications and Capacities in this chapter.DRIVELINE UNIVERSAL JOINT AND

2. Release three retainer clamps.3. Pull air filter cover toward passenger side of vehicle and up to releasethe tabs. Lift air filter element up and o

MOTORCRAFT PART NUMBERSComponent 5.4L V8/6.8L V10 enginesAir filter element FA-1883Fuel filter FG-1011Oil filter FL-820-SPCV valve1Battery (Standard)

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationFront axle 5.8 pints (2.8L)Motorcraft

Item Capacity Ford part nameFord part number /Ford specificationEngine coolant - 6.8LV10 engine227.5 quarts(26.0L)Motorcraft PremiumGold Engine Coolan

12. Memory presets: To set astation: Select frequency bandAM/FM1/FM2; tune to a station,press and hold a preset control until sound returns. You may s

Item Capacity Ford part nameFord part number /Ford specificationHinges, latches, strikerplates, fuel filler doorhinge and seat tracks— Multi-Purpose G

Item Capacity Ford part nameFord part number /Ford specificationWindshield washer fluid 3.5 quarts (3.3L)Motorcraft PremiumWindshield WasherConcentrat

ENGINE DATAEngine 5.4L V8 engine 6.8L V10 engineCubic inches 330 415Required fuel 87 octane 87 octaneFiring order 1-3-7-2-6-5-4-8 1-6-5-10-2-7-3-8-4-9

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

1. World manufacturer identifier2. Brake type and gross vehicleweight rating (GVWR)3. Vehicle line, series, body type4. Engine type5. Check digit6. Mo

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford

Cargo organization and managementTowing mirrorsTrailer hitches, wiring harnesses and accessoriesPeace of mindMobile-Ease™ hands-free communication sys

AAccessory delay ...105Air cleaner filter ...375, 377Air conditioning ...81Airbag supplemental

Climate control (see Airconditioning or Heating) ...81Clock adjust6-CD in dash ...34AM/FM/CD ...

refill capacities ...378Event data recording ...6Exhaust fumes ...255FFail safe cooling .

turned off, the volume will come back on at a “nominal” listening levelwhen the ignition switch is turned back on.16. CD: Press to enter CD/MP3mode. I

lighting up panel andinterior ...87JJump-starting your vehicle ...318KKeyless entry system ...155au

fluid, checking and adding ...369fluid, refill capacity ...378Power Windows ...103Preparing to drive yourvehicle .

Tires ...203–205alignment ...213care ...209changin

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

Auxiliary input jack (if equipped)Your vehicle may be equipped withan Auxiliary Input Jack (AIJ). TheAuxiliary Input Jack, located on theinstrument pa

compatible with the AIJ. The AIJ will only work correctly with devicesthat have a headphone output with a volume control.2. Do not set the portable mu

CD/CD player careDo:• Handle discs by their edges only.Never touch the playing surface.• Inspect discs before playing.Clean only with an approved CDcl

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m

Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The

FAMILY ENTERTAINMENT DVD SYSTEM (IF EQUIPPED)Driving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recomme

3. Press the power button on theDVD player, then press Play ()to begin to play the disc.If a DVD is already loaded into thesystem, press PLAY on the D

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

3. The disc will begin to play andthe ’CD Audio Disc’ screen willdisplay. From this screen, you canalso select from COMPRESSION,SHUFFLE and SCAN featu

3. Connect an auxiliary audio/videosource by connecting RCA cords(not included) to the RCA jacks onthe left hand side of the system.• Yellow (1) — vid

Using the infrared (IR) wireless headphones:1. Press the power control on the earpiece to turn the headphones ON.2. Select Channel A or B for each set

DVD player controls1. Headphone control A/B: Pressto select either the A or Bheadphone source. Then pressMEDIA to select the desired playingmedia for

4. (Fast forward): Press andrelease for the next chapter ortrack. Press and hold to forwardsearch a DVD, Video CD, or FES CD in DVD/CD mode.5./ (Play/

press the 2 and 4 memory preset buttons on the audio system at thesame time to perform the same function. For further interactioninformation, refer to

1. Power control: Press to turn the FES (Family EntertainmentSystem) ON/OFF.2. Cursor controls: Use in various active menus to advance the cursorup/do

(Wireless headphone volume is controlled with the rotary dial on theright ear piece.)8. Fast Forward/Next: In DVD mode, press and hold for a quickadva

23. ILLUMINATION: Press to illuminate the remote control andbacklight all of the buttons.Battery replacementBatteries are supplied with the remote con

HeadphonesWireless headphonesYour FES system is equipped withtwo sets of battery powered,infrared wireless headphones. TwoAAA batteries are needed to

Service Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This pote

To install the batteries, remove the screw at the bottom of the cover.Then, lightly press down on top and slide the cover off.When replacing the batte

To operate the headphones:• Press POWER on the ear piece to turn on the headphones. A redindicator light will illuminate indicating the headphones are

Wired headphonesDo not leave children unattended in the vehicle and do not letchildren operate the system while unsupervised. If wiredheadphones or au

DVD and Rear Seat Controls turned ON, the rear seat passengers maychoose to listen to the radio, CD, MP3, DVD, or DVD-AUX media sourcesover headphones

While operating in Headphone Only Mode, the system will have limitedfunctionality.• The system will only output audio to the headphones. It will not b

Aspect ratioSelect ASPECT RATIO to select theviewing size and shape of the videodisplayed on the LCD screen. This isdisc dependent.You can select from

SubtitlesSelect SUBTITLES to turn thesubtitle option on or off. The systemdefault is OFF.Once you have made your selection,press ENTER to confirm. Thi

SCAN: Press for a brief sampling of all tracks on the current CD. Pressagain to stop.Playing MP3 discsTo play an MP3 disc on your DVD system:1. Ensure

effect on sound quality and are recommended only for speech or lowfidelity music material. We recommend that you encode MP3 filesusing a high quality

Playing a DVD1. Ensure that the vehicle ignition is in the RUN or ACCESSORYposition.2. Ensure that the navigation system is on.3. Insert a DVD label-s

if the modification is removed. When a dealer or repair facility works onyour vehicle, it may be necessary for them to access the information inthe Po

Frame by frame1. With a DVD playing, press pause.2. Press the right cursor button. TheDVD will advance one frame. Eachpress of the right cursor button

The B headphone jack (5) is locatedon the right side of the DVD system.Plug in wired headphones (notincluded) here.Note: The B headphones can onlyacce

FULL (enabled): The FES has control over the primary (speaker) andsecondary (headphone) audio sources.LOCAL: The FES has control over the secondary so

use this product in any commercial (i.e. revenue generating) real timebroadcasting (terrestrial, satellite, cable and /or any other media)broadcasting

Be sure to review User Manuals for video games and video gameequipment when used as auxiliary inputs for your Family EntertainmentSystem (FES).Do not

• locations where strong magnetic fields are generated.Temperature extremesWhen the vehicle is parked under direct sunlight or in an extremely coldpla

While operating in Headphone Only Mode, the system will have limitedfunctionality.• The system will only output audio to the headphones. It will not b

HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe

To increase airflow to the outer instrument panel vents, close the ventslocated in the middle of the instrument panel.Do not place objects on top of t

1. Fan speed adjustment: Controls the volume of air circulated in thevehicle.2. Temperature selection: Controls the temperature of the airflow inthe v

Notice to owners of pickup trucks and utility type vehiclesUtility vehicles have a significantly higher rollover rate thanother types of vehicles.Befo

Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEMS(IF EQUIPPED)• DATC• DATC with heated mirrors2008 F-250/350/450/550 (f23)Owners Guide (post-2002-fmt)

• DATC with heated seats and heated mirrorsTemperature conversion: To switch between Fahrenheit and Celsius,refer to Units (English/Metric) under eith

odors from reaching the interior of the vehicle. Recirculation can beengaged manually in any other airflow selection except(defrost).Recirculation may

• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield.• To improve the A/C cool down, drive with the windows slightly

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola

Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the ON position,• the head

PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicableilluminated switches in the vehicleduring headlamp and parkl

To adjust the headlamps:1. Park your vehicle on a levelsurface about 25 feet (7.6 meters)away from a vertical plain surface(3). Check your headlamp al

5. Locate the vertical adjuster (2)for each headlamp. Adjust the aimby turning the adjuster controleither clockwise (to adjust up) orcounterclockwise

If your vehicle is equipped with theFord Ambulance PreparationPackage, it will be indicated on theSafety Compliance CertificationLabel. The label is l

• (4) Horizontal reference line2. Measure the height from thecenter of your headlamp (indicatedby a 3.0 mm circle on the lens) tothe ground and mark a

TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.MAP LAMPS (IF EQUIPPED)The dome lamp turns o

Using the right bulbsCheck the operation of all the bulbs frequently.Function Numberof bulbsTrade numberHeadlamps (aerodynamic) 2 H13/9008Headlamps (s

Replacing exterior bulbsReplacing headlamp bulbs (aerodynamic)1. Make sure that the headlamp control is in the OFF position and openthe hood.2. Remove

Replacing park/turn and sidemarker lamp bulbs (aerodynamic)1. Make sure that the headlamp control is in the OFF position and openthe hood.2. Remove th

Replacing headlamp bulbs (sealed beam)1. Make sure that the headlamp control is in the OFF position and openthe hood.2. Remove the three screws and on

Replacing park/turn/sidemarker bulbs (sealed beam)1. Make sure that the headlamp control is in the OFF position and openthe hood.2. Remove the three s

Replacing brake/tail/turn/back-up lamp bulbs - Pick-ups only1. Make sure the headlamp switch isin the OFF position and then openthe tailgate to expose

Replacing cargo lamp and high-mount brakelamp bulbs1. Make sure the headlamp switch isin the OFF position.2. Remove the two screws and lampassembly fr

Replacing license plate lamp bulbsThe license plate bulbs are locatedbehind the rear bumper. To changethe license plate lamp bulbs:1. Reach behind the