Ford 2007 Freestyle v.2 Manuel d'utilisateur

Introduction 4Instrument Cluster 10Warning lights and chimes 10Gauges 14Entertainment Systems 16AM/FM stereo with CD 16AM/FM stereo with in-dash six C

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A wa

and the vehicle is locked using the remote entry transmitter or thekeyless entry keypad. The door lock controls are re-enabled when thevehicle is unlo

• When the childproof door locks are set, the rear doors cannot beopened from the inside.• The rear doors can be opened from the outside when the powe

Unlocking the doors1. Press and release to unlock the driver’s door. Note: The interiorlamps will illuminate.2. Pressand release again within three se

Memory seats/power mirrors/adjustable pedals (if equipped)The remote entry system can also control the memory seat /powermirrors/adjustable pedals fea

Replacing the batteryThe remote entry transmitter uses one coin type three-volt lithiumbattery CR2032 or equivalent.To replace the battery:1. Twist a

transmitters, you can either reprogram them yourself, or take allremote entry transmitters to your authorized dealer forreprogramming.Note: If your ve

Illuminated entryThe interior lamps illuminate when the remote entry system or thekeyless entry system keypad (if equipped) is used to unlock the door

1. Place the key in the ignition andturn the ignition to the 3 (RUN)position.2. Press the power door unlockcontrol on the door panel threetimes.3. Tur

KEYLESS ENTRY SYSTEMYou can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• activate or deactivate theautolock feature.

Tips:• Do not set a code that uses five of the same number.• Do not use five numbers in sequential order.• The factory set code will work even if you

Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interiorfloor coverings or other

Your vehicle comes with two coded keys; additional coded keys may bepurchased from your authorized dealer. The authorized dealer canprogram your spare

Automatic disarmingThe vehicle is disarmed immediately after the ignition is turned from the1 (LOCK) to the 3 (RUN) position.The theft indicator will

3. Turn the ignition to the 1 (LOCK) position and remove the first codedkey from the ignition.4. Within ten seconds of turning the ignition to the 1 (

The system is ready to arm whenever the key is removed from theignition. Any of the following actions will prearm the alarm system:• Press thecontrol

Disarming the systemYou can disarm the system by any of the following actions:• Unlock the doors by using your remote entry transmitter.• Unlock the d

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

Push release button to lower headrestraint.Adjusting the front manual seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle is

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback.After returning the sea

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback.After returning the sea

Press the front or rear portion to tiltthe seat.• DriverPress the control to move the seatforward, backward, up or down.• DriverPress the control to m

Airbag readiness: If this light failsto illuminate when ignition is turnedto ON, continues to flash or remainson, have the system servicedimmediately

Memory seats/power mirrors/adjustable pedals (if equipped)This system allows automaticpositioning of the driver seat, powermirrors, and adjustable ped

REAR SEATSHead restraintsLift the head restraint so that it is located directly or as close as possiblebehind your head.The head restraints can be mov

Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a collision.Ad

The seatback will fold flat.Lift the handle all the way up untilthe seat releases from the floor.Rotate the seat forward to allowaccess to the third r

Note: The seatback will not raise if the rear latch hooks are not properlyengaged to the floor striker.• Pull the head restraint back up to its normal

To return the seatback to theupright position• Lift the seatback toward the rearof the vehicle, and• Rotate the seatback until youhear a click, lockin

Stowing the third row bench or split bench seat (if equipped)1. Stow the head restraints bypushing the head restraint releasebuttons while sliding the

Do not use the seat anchors as cargo tie downs.Note: Do not use the third row seatback as a load floor when theseatback is folded.Unstowing the third

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback.After returning the sea

• Restraints Control Module (RCM) with impact and safing sensors.• Restraint system warning light and back-up tone.• The electrical wiring for the air

Low fuel (if equipped):Illuminates when the fuel level inthe fuel tank is at or near empty(refer to Fuel gauge in thischapter).Speed control: Illumina

Driver’s seat position sensorThe driver’s seat position sensor allows your Personal Safety System娂 totailor the deployment level of the driver dual-st

safety belt pretensioner activation depending upon safety belt usage.Refer to Safety belt section in this chapter.Front safety belt pretensionersThe s

Safety belt precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injury, mak

Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until

All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of l

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl

Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could re

hardware, should be inspected after a collision. Ford Motor Companyrecommends that all safety belt assemblies in use in vehicles involved ina collisio

The Belt-Minder威 feature uses information from the front passengersensing system to determine if a front seat passenger is present andtherefore potent

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra

Headlamps on warning chime: Sounds when the headlamps or parkinglamps are on, the ignition is off (the key is not in the ignition) and thedriver’s doo

Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate

• The ignition switch is in the OFF position• The driver and front passenger safety belts are unbuckledWhile the design allows you to deactivate your

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The instrument panel grab handle should never be used forstorage. The path of an inflating airbag must be ke

Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in

• Recline the seat slightly one or two degrees from the upright position.Do not put anything on or over the air bag module. Placingobjects on or over

How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suffic

Several air bag system components get hot after inflation. Do nottouch them after inflation.If the air bag has deployed, the air bag will not function

The front passenger sensing system will disable (will not inflate) thefront passenger’s frontal airbag if:• the front passenger seat is unoccupied, or

The front passenger sensing system is designed to enable (may inflate)the front passenger’s frontal airbag anytime the system senses that aperson of a

Sitting improperly out of position or with the seat back reclinedtoo far can take off weight from the seat cushion and affect thedecision of the front

Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe

To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a child is in

Any alteration/modification to the front passenger seat mayaffect the performance of the front passenger sensing system.Determining if the system is o

Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See yourauthorized dealer.All

The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuittha

Do not lean your head on the door. The Safety Canopy娂 couldinjure you as it deploys from the headliner.Do not attempt to service, repair, or modify th

• A headliner designed to flex open above the side doors to allow SafetyCanopy娂 deployment.• The same readiness airbag light, electronic control and d

If the Safety Canopy娂system has deployed, theSafety Canopy娂 will notfunction again unless replaced.The Safety Canopy娂 system(including the A, B, C, an

SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme

Child booster seatsChildren outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the la

Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi

AUDIO SYSTEMSAM/FM stereo/ single CD Satellite Compatible sound system(if equipped)Accessory delay: Your vehicle is equipped with accessory delay. Wit

Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in acollision.SAFETY SEATS F

tether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. Formore info

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a

Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a

Front passenger seating position (delivery van only)1. Position the child safety seat onthe passenger seat cushion.2. Route the child safety seat teth

4. Rotate the tether hook, and clipthe tether strap to the seat frame.If the tether strap is clippedincorrectly (as shown) thechild safety seat may no

7. Tighten the child safety seattether strap according to themanufacturer’s instructions.Rear seating positionsFollow Steps 1–7 as described above for

• 3rd row benchNote: The cargo tie-downs at therear edge of the floor are nottether anchors.For additional important safety information on the proper

2. Phone/mute: Press to mute theplaying media. Press again to returnto the playing media.3. Menu: Press to toggle throughthe following modes:CATEGORY

The lower anchors for child seatinstallation are located at the rearsection of the rear seat between thecushion and seat back.Follow the child seat ma

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles handle differentlythan passenger cars in the variousdriving conditions that areencountered

NOTE: Your AWD vehicle is not intended for off-road use. The AWDfeature gives your vehicle some limited off-road capabilities in whichdriving surfaces

• Narrower — to provide greatermaneuverability in tight spaces.As a result of the above dimensionaldifferences, Utility Vehicles oftenwill have a high

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Every day before you drive, check your tires. If one

The cold inflation pressure should never be set lower than therecommended pressure on the Safety Compliance Certification Label orTire Label.When weat

TIRE CAREInspecting your tiresPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones, nails or glass that

AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressure, etc.)

Setting the clock: Press MENU until SELECT HOUR or SELECTMINUTE is displayed. Use/ to manually increase/decrease. PressMENU again to disengage clock m

Only use replacement tires and wheels that are the same size,load index, speed rating and type (such as P-metric versusLT-metric or all-season versus

Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t

Tire rotationRotating your tires at the recommended interval (as indicated in thescheduled maintenance information that comes with your vehicle) willh

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

SNOW TIRES AND CHAINSSnow tires must be the same size and grade as the tires youcurrently have on your vehicle.The tires on your vehicle have all weat

7. Shuffle: Press to play tracks inrandom order.8. Comp (Compression): In CDmode, brings soft and loud CDpassages together for a moreconsistent listen

provide maximum return of vehicle design performance. Before loadingyour vehicle, familiarize yourself with the following terms for determiningyour ve

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

Steps for determining the correct load limit:1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.

would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 - 540 =-103 kg. You will need to reduce the load weight by at least 240 lb.(104 kg). If you

Preparing to towUse the proper equipment fortowing a trailer and make sure it isproperly attached to your vehicle.Use a trailer hitch with at leastthr

Trailer lampsTrailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working.

RECREATIONAL TOWINGFollow these guidelines for your specific powertrain combination to towyour vehicle for personal travel (such as behind a recreatio

STARTINGPositions of the ignition1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and a

Seating and Safety Restraints 115Seating 115Safety restraints 128Airbags 142Child restraints 157Tires, Wheels and Loading 171Tire information 173Tire

In Satellite Radio mode (if equipped), press SEEK to seek to theprevious channel. If a specific category is selected, (Jazz, Rock, News,etc.), pressto

Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,

• Make sure the gearshift lever is inP (Park).3. Turn the key to 3 (RUN) withoutturning the key to 4 (START).Some warning lights will briefly illumina

Guarding against exhaust fumesCarbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects.If you smell exhaust fumes i

Four-wheel anti-lock brake system (ABS)Your vehicle is equipped with an Anti-lock Braking System (ABS). Thissystem helps you maintain steering control

Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th

TRACTION CONTROL姟 (IF EQUIPPED)Your vehicle may be equipped with a Traction Control娂 system. Thissystem helps you maintain the stability and steerabil

STEERINGTo help prevent damage to the power steering system, never hold thesteering wheel at its furthest turning points (until it stops) for more tha

2. Remove the console panel byopening the armrest, grasping thepanel firmly, then pulling up. Thiswill allow access to the gearshiftassembly.3. Locate

Understanding the gearshift positions of the Continuously VariableTransaxle (CVT)The CVT is a fully automatic transaxle that electronically monitorsve

To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)Always set the parking brake full

Premium/Audiophile In-Dash Six CD/MP3 Satellite CompatibleSound System (if equipped)Accessory delay: Your vehicle is equipped with accessory delay. Wi

This system is not designed to prevent contact with small ormoving objects. The system is designed to provide a warning toassist the driver in detecti

in any gear, the ignition must be ON. An indicator light on the controlwill illuminate when the system is turned off. If the indicator lightilluminate

Basic operating principles• Drive slower in strong crosswinds which can affect the normal steeringcharacteristics of your vehicle.• Be extremely caref

If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly.See your authorized deal

Mud and waterIf you must drive through high water, drive slowly. Traction or brakecapability may be limited.When driving through water, determine the

seeing what conditions are on the other side. Do not drive in reverseover a hill without the aid of an observer.When climbing a steep slope or hill, s

Make sure you allow sufficient distance between you and other vehiclesfor stopping. Drive slower than usual and consider using one of the lowergears.

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsUsing roadside assistanceComplete the roadside assi

FUEL PUMP SHUT-OFF SWITCHThis device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt.After an

2. Phone/mute: Press to mute theplaying media. Press again to returnto the playing media.3. Menu: Press to toggle throughthe following modes:CATEGORY

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge5A Tan Tan — — —7.5A Brown Br

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionF1 20A High beamsF2 15A Interior lamps (Cour

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionF15 10A Delayed accessory (Driver windowmotor logic, Auxiliary climatecontr

Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription3 50A* Front and rear wipers (fuses 45and 47)4 — Not used5 20A* Moonroof6 — Not used7

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription28 80A* SJB power, SJB (Circuit breaker,Fuses 6, 7, 9, 10, 11 and 15)29 30A* Driver w

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription52 Full ISO relay Front A/C blower motor, Coolantpump relay coil53 — Not used54 — Not

A dissimilar spare tire/wheel is defined as a spare tire and/or wheel thatis different in brand, size or appearance from the road tires and wheelsand

• Use snow chains on the end of the vehicle with the dissimilar sparetire/wheelThe usage of a full-size dissimilar spare tire/wheel can lead toimpairm

1. Remove the carpeted floor panellocated in the rear of the vehicle,remove the wing nut that securesthe spare tire by turning itcounterclockwise.2. L

Speed sensitive volume: Radio volume automatically changes slightlywith vehicle speed to compensate for road and wind noise.Use/ / SEEK to adjust. Rec

To help prevent the vehicle from moving when you change a tire,be sure to place the transaxle in P (Park), set the parking brakeand block (in both dir

4. Put the jack in the jack notchnext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is completely off theground.5. Remove

Stowing the tire and jack1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown.

If you are stowing the flat tire,remove the “L”-shaped bolt from thelarge wing nut used to secure thespare tire in the vehicle. With the3rd row seat i

JUMP STARTINGThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury orvehicle da

Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

5. Seek: In radio mode, press toaccess the next strong station.In CD mode, pressto access thenext CD track.In Satellite Radio mode (if equipped), pres

In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, flatbed transport vehicle or a car hauling trailer) yourvehic

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio

ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro

To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is

11. Rewind: Press to manuallyreverse in a CD track.12. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, press andhold a

WAXINGApplying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage.• Wash the ve

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub

• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to a

Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing.Do not use chemical solvents or

Motorcraft Car Wash (Canada only) (CXC-21)Motorcraft Custom Bright Metal Cleaner (ZC-15)Motorcraft Custom Clear Coat Polish (ZC-8-A)Motorcraft Custom

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column.2. Go to th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.0L DOHC V6 DURATEC ENGINE1. Engine coolant reservoir2. Power steering fluid reservoir3. Brake fluid

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

16. ON/OFF/Volume: Press to turnON/OFF. Turn to increase/decreasevolume.If the volume is set above a certainlevel and the ignition is turned off,the v

CHANGING THE WIPER BLADES1. Pull the wiper arm away from the vehicle slightly.2. Press the release button and pull the wiper blade from the wiper arm.

5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.•

• If required, add engine oil to theengine. Refer to Adding engineoil in this chapter.• Do not overfill the enginewith oil. Oil levels above thismark

Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by th

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyeswhen working near

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur

1. Before you begin, turn the engine off and let it cool.2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the c

CD/CD player careDo:• Handle discs by their edges only. Never touch the playing surface.• Inspect discs before playing. Clean only with an approved CD

8. Add coolant/water mixturethrough the thermostat housingopening until full at housingopening.9. Install the thermostat housingbleed plug. Install me

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your coolin

• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damag

Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforerefueling your vehicle.• Al

RefuelingFuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others:• Read and follow all the instr

If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any

Octane recommendationsYour vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofga

Running out of fuelAvoid running out of fuel because this situation may have an adverseeffect on powertrain components.If you have run out of fuel:• Y

For consistent results when filling the fuel tank:• Turn the engine/ignition switch to the off position prior to refueling,an error in the reading wil

Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

• Adding certain accessories to your vehicle (for example bugdeflectors, rollbars/light bars, running boards, ski/luggage racks) mayreduce fuel econom

emission control, such non-Ford parts should be equivalent to genuineFord Motor Company parts in performance and durability.Do not park, idle, or driv

2. Poor fuel quality or water in the fuel—the engine may misfire or runpoorly.3. The fuel cap may not have been securely tightened. See Fuel fillercap

The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not

BRAKE FLUIDThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“

If your transaxle does not engage normally, do not attempt todrive. The vehicle should be towed to your authorized dealer forevaluation.MOTORCRAFT PAR

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItems CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationBrake fluidBetween MAX a

Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine oil 6.0 quarts (5.7L)Motorcraft SAE 5W-20Premium SyntheticBlend Mo

ENGINE DATAEngine 3.0L-DOHC V6 engineDisplacement 183 cubic inchesRequired fuel 87 octaneFiring order 1–4–2–5–3–6Spark plug gap (0.052–0.056 inch) 1.3

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

Peace of mindMobile-Ease娂 hands free communication systemRemote startVehicle security systemsWheel locksNot all accessories are available for all mode

AAccessory delay ...74Air cleaner filter ...285Air conditioning ...48, 50, 52, 54Airbag supplemental r

interior ...253plastic parts ...251washing ...249waxing ..

FFamily entertainment system ...30Fluid capacities ...286Foglamps ...59Four-Wheel Drive vehic

autolock ...98keypad ...108locking and unlocking doors ..109programming entry code

Rear seat entertainmentsystem ...30Relays ...219Remote entry system ...

terminology ...175tire grades ...174treadwear ...174, 178Towing ...

299

Maintenance and Specifications 256Engine compartment 258Engine oil 260Battery 264Engine coolant 266Fuel information 272Part numbers 285Maintenance pro

Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The

300

301

302

303

304

DVD player controls1. MAIN control• NEXT — Press to access the next track on the CD, the next chapteron the DVD, or to go up in cursor mode.• PREV — P

6. AUX controlPress to switch DVD player from play mode to auxiliary mode.7. Auxiliary jacksInput jacks for standard video/audio media device.8. STOP/

• Press the REV control to movethe cursor left one position• Press the FWD control to movethe cursor right one positionNext/Previous controlThe NEXT (

CD play modePress NEXT during CD play toadvance to the next track. If youpress NEXT while the last track isplaying, the system will wrap aroundto the

Remote control1. REV (REVERSE) controlPress to reverse the direction of the DVD movie.2. FWD (FORWARD) controlPress to advance the direction of the DV

7. MENU/MODE controlIn DVD playback mode, press to access the disc menu.In stop mode, press to change media types (e.g. AM, FM, CD...)8. VOL (VOLUME)

Battery replacementBatteries are provided with the remote control unit. Since all batterieshave a limited shelf life, replace them when the remote con

Wireless headphone operationTo operate the headphones:• Press the ON/OFF button on theearpiece to turn on theheadphones. A red LED(indicator light) wi

Liquid Crystal Display (LCD) flip-down screenThe LCD screen rotates down and can be adjusted to your desiredviewing angle. When not in use, rotate the

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

• Always save MP3 files with the .mp3 extension. The player recognizesan MP3 file by the .mp3 extension, so MP3 files saved with differentextensions w

This unit is designed to play commercially pressed 4.75 (12 cm)audio compact discs and DVDs only. Due to technicalincompatibility, certain recordable

On-screen indicatorsEach time a control is pressed, the operational status of the DVD playeris shown on the screen. The following are some possible in

The front glass on the flip-down liquid crystal display (LCD) maybreak when hit with a hard surface. If the glass breaks, do nottouch the liquid cryst

Care and service of the DVD playerEnvironmental extremesDVD players that are subjected to harsh environmental conditions maybe damaged or perform at l

Cleaning the DVD playerClean the exterior of the DVD player with a damp cloth. Do not use CDcleaning kits or CDs intended to clean the interior of you

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele

6. Fan speed adjustment: Controls the volume of air circulated in thevehicle.Operating tips• To reduce fog build up on the windshield during humid wea

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED)1.Defrost: Distributes outside air through the windshield defrosterand demister vents. Can be used

8. : Distributes air through the instrument panel and floor vents.9.: Distributes air through the instrument panel vents.10. Manual override controls:

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

Dual Zone Automatic Temperature Control with heated seats(if equipped)1.Defrost: Distributes outside air through the windshield defrosterand demister

8. Airflow direction control: Press to toggle through the airdistribution modes listed below. The selected mode will be shown in thedisplay.: Distribu

Dual Zone Automatic Temperature Control with rear passengercompartment climate control (if equipped)1.Defrost: Distributes outside air through the win

odors from reaching the interior of the vehicle. Recirculation can beengaged manually in any other airflow selection except defrost.Recirculation may

Dual Zone Automatic Temperature Control with heated seats andrear passenger compartment climate control (if equipped)1.Defrost: Distributes outside ai

7. Recirculated air: Press to activate/deactivate air recirculationin the cabin. Recirculated air may reduce the amount of time to cooldown the interi

17. Driver temperature control: Press to increase/decrease thetemperature on the driver side of the cabin. Sets the passenger sidetemperature also whe

4. Set the fan to the highest speed.5. Direct the outer instrument panel vents towards the side windows.Do not place objects on top of the instrument

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola

5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamp switch to. The headlampswill turn off.Fogl

SPECIAL NOTICESNew Vehicle Limited WarrantyFor a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited

Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the ON position,• the head

• (1) 8 feet (2.4 meters)• (2) Center height of lamp toground• (3) 25 feet (7.6 meters)• (4) Horizontal reference line2. Measure the height of thehead

TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSDome lamps and map lampsThe ma

Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an

3. Locate the outboardmostelectrical connector and remove itby releasing the locking tab andpulling it off.4. Remove the bulb socket byturning it coun

3. Locate the front sidemarker lampelectrical connector and remove itby pulling it off.4. Remove the bulb socket byturning it counterclockwise andpull

Replacing high-mount brake lamp bulbs1. Make sure the ignition control isin the OFF position.2. Remove the two screws.3. Unclip the bulb holder from t

MULTI-FUNCTION LEVERWindshield wiper: For intermittentoperation, move control up oneposition.Adjust the rotary control to thedesired speed setting.Mis

Rear window wiper/washer controlsFor rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select:2 — Three to f

ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamp. The visor willslide back and forth on the rod forincrease

• how fast the vehicle was traveling; and• where the driver was positioning the steering wheel.To access this information, special equipment must be d

OVERHEAD CONSOLEThe appearance of your vehicle’s overhead console will vary according toyour option package.Storage compartmentPress the latch to open

CENTER CONSOLEYour vehicle may be equipped with a variety of console features. Theseinclude:• Utility compartment with powerpoint• Gear Shift• Cup hol

AUXILIARY POWER POINT (12VDC)Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will damag

When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not inthe proximity of the win

Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controlsexcept for the driver’s press

AUTOMATIC DIMMING INTERIOR REAR VIEW MIRROR(IF EQUIPPED)Your vehicle may be equipped withan interior rear view mirror with anauto-dimming function. Th

Fold-away mirrorsPull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.Heated outside mirrors(if equipped)B

Memory feature (if equipped)The accelerator and brake pedal positions are saved when doing amemory set function and can be recalled along with the veh

• If the vehicle speed increases above the set speed on a downhill, youmay want to apply the brakes to reduce the speed.• If the vehicle speed decreas

Reducing speed while using speed controlThere are two ways to reduce a setspeed:• Press and hold the SET - controluntil you get to the desiredspeed, t

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

STEERING WHEEL CONTROLS (IF EQUIPPED)Radio control featuresPress MEDIA to select:• AM, FM1, FM2• SAT1, SAT2 or SAT3 (SatelliteRadio mode if equipped).

Do not let children play with the moon roof or leave childrenunattended in the vehicle. They may seriously hurt themselves.To open the moon roof:The m

HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED)The HomeLink威 Wireless ControlSystem, located on the driver’s visor,provides a convenient way toreplace

1. Press and hold the two outsidebuttons releasing only when theindicator light begins to flash after20 seconds. Do not repeat Step 1to program additi

Note: There are 30 seconds in which to initiate Step 7.7. Return to the vehicle and firmly press, hold for two seconds andrelease the programmed HomeL

Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet

MESSAGE CENTER (IF EQUIPPED)With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle info

DTE is calculated using a running average fuel economy, which is basedon your recent driving history of 500 miles (800 km). This value is notthe same

Trip elapsed drive timeSelect this function from the INFOmenu to display a timer.To operate the Trip Elapsed DriveTime perform the following:1. Press

Note: If message center displays the message ⬙SLOW CIRCLES TOCALIBRATE⬙, then perform the CALIBRATION PROCEDURE.4. Determine your magnetic zone byrefe

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

Note: If message center displays the message ⬙SLOW CIRCLES TOCALIBRATE⬙, then continue with Step 4. Otherwise, if a heading isdisplayed, continue with

3. Press and hold the RESETcontrol to set the language choice.Units (English/Metric)1. Select this function from theSETUP menu for the current unitsto

System warningsSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems.In the event of a multiple warning si

PASSENGER DOOR AJAR. Displayed when the passenger side door isnot completely closed.LEFT REAR DOOR AJAR. Displayed when the left rear door is notcompl

To reset the oil monitoring system to 100% after each oil change[approximately 5,000 miles (8,000 km) or 180 days] perform thefollowing:To reset the o

3. Press and hold RESET controlagain until OIL LIFE SET TO 100%is displayed. Your oil life is nowreset.LIFTGATEUnlock the liftgate (but do notrelease

CARGO AREA FEATURESCargo net (if equipped)The cargo pouch net secureslightweight objects in the cargoarea. Attach the net to the anchorsprovided. Do n

LUGGAGE RACKMaximum load is 125 lbs (57 kg) on the roof rack structure, or 100 lbs(45 kg) on the roof panel, evenly distributed. If it is not possible

KEYSOne key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency.Your keys are programmed to your v

Deactivating/activating autolockYour vehicle comes with the autolock feature activated. There are threemethods to enable/disable this feature: One is