Introduction 4Instrument Cluster 10Warning lights and chimes 10Gauges 14Entertainment Systems 16AM/FM stereo with CD 16AM/FM stereo with in-dash six C
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A wa
CHILDPROOF DOOR LOCKS• Move control up to engage thechildproof lock.• Move control down to disengagechildproof lock.The childproof locks are located o
The remote entry system allows youto lock or unlock all vehicle doorswithout a key.The remote entry lock/unlock feature operates in any ignition posit
and the turn lamps will flash once if all the doors and liftgate are closed.If any door or the liftgate is not closed, or if the hood is not closed in
Replacing the batteryThe remote entry transmitter uses one coin type three-volt lithiumbattery CR2032 or equivalent.To replace the battery:1. Twist a
Note: If your vehicle is equipped with the memory seats/powermirrors/adjustable pedals feature, you can associate a remote entrytransmitter to each me
Illuminated entryThe interior lamps illuminate when the remote entry system or thekeyless entry system keypad (if equipped) is used to unlock the door
KEYLESS ENTRY SYSTEMYou can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• activate or deactivate theautolock feature.
Tips:• Do not set a code that uses five of the same number.• Do not use five numbers in sequential order.• The factory set code will work even if you
Your vehicle comes with two coded keys; additional coded keys may bepurchased from your authorized dealer. The authorized dealer canprogram your spare
Automatic disarmingThe vehicle is disarmed immediately after the ignition is turned from the1 (LOCK) to the 3 (RUN) position.The theft indicator will
Check fuel cap (if equipped):Illuminates when the fuel cap maynot be properly installed. Continueddriving with this light on may causethe Check engine
3. Turn the ignition to the 1 (LOCK) position and remove the first codedkey from the ignition.4. Within ten seconds of turning the ignition to the 1 (
The system is ready to arm whenever the key is removed from theignition. Any of the following actions will prearm the alarm system:• Press thecontrol
Disarming the systemYou can disarm the system by any of the following actions:• Unlock the doors by using your remote entry transmitter.• Unlock the d
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Push release button to lower headrestraint.Adjusting the front manual seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle is
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback.After returning the sea
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback.After returning the sea
Press the front or rear portion to tiltthe seat.• DriverPress the control to move the seatforward, backward, up or down.• DriverPress the control to m
The indicator light on the control will illuminate when activated. For lowheat, one light will be lit; for high heat, both lights will be lit.The heat
The head restraints can be movedup by pulling up on the headrestraint.Push release button to lower headrestraint.Adjusting second row bucket and bench
Safety belt: Reminds you to fastenyour safety belt. A BeltMinder威chime will also sound to remind youto fasten your safety belt. Refer tothe Seating an
Adjusting second row seats (if equipped)Lift the control to adjust the seatforward or backward.Accessing the third row seatsFold and tumble the second
Lift the handle all the way up untilthe seat releases from the floor.Rotate the seat forward to allowaccess to the third row.To return the seatback to
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback.After returning the sea
To return the seatback to theupright position• Lift the seatback toward the rearof the vehicle, and• Rotate the seatback until youhear a click, lockin
Stowing the third row bench or split bench seat (if equipped)1. Stow the head restraints bypushing the head restraint releasebuttons while sliding the
Do not use the seat anchors as cargo tie downs.Note: Do not use the third row seatback as a load floor when theseatback is folded.Unstowing the third
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback.After returning the sea
• Restraints Control Module (RCM) with impact and safing sensors.• Restraint system warning light and back-up tone.• The electrical wiring for the air
Driver’s seat position sensorThe driver’s seat position sensor allows your Personal Safety System娂 totailor the deployment level of the driver dual-st
safety belt pretensioner activation depending upon safety belt usage.Refer to Safety belt section in this chapter.Front safety belt pretensionersThe s
Speed control: Illuminates whenthe speed control is engaged. Turnsoff when the speed control systemis disengaged.Low washer fluid (if equipped):Illumi
Safety belt precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injury, mak
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of l
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could re
assemblies, buckle support assemblies (slide bar-if equipped), shoulderbelt height adjusters (if equipped), shoulder belt guide on seatback (ifequippe
BeltMinder姞The BeltMinder威 feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders byintermit
If... Then...The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately 1minute while the vehicle istraveling at least 3 mph (5km
Reasons given... Consider...“Traffic is light” Nearly 1 of 2 deaths occur insingle-vehicle crashes, many whenno other vehicles are around.“Belts wrink
Read Steps1-4thoroughly before proceeding with thedeactivation/activation programming procedure.Note: The driver and front passenger BeltMinder威 featu
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
• This will enable the BeltMinder威 feature for that seating position if itis currently disabled. As confirmation, the safety belt warning light willfl
Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in
• Recline the seat slightly one or two degrees from the upright position.Do not put anything on or over the air bag module. Placingobjects on or over
How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suffic
Several air bag system components get hot after inflation. Do nottouch them after inflation.If the air bag has deployed, the air bag will not function
The front passenger sensing system will disable (will not inflate) thefront passenger’s frontal airbag if:• the front passenger seat is unoccupied, or
The front passenger sensing system is designed to enable (may inflate)the front passenger’s frontal airbag anytime the system senses that aperson of a
Sitting improperly out of position or with the seat back reclinedtoo far can take off weight from the seat cushion and affect thedecision of the front
To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a child is in
Any alteration/modification to the front passenger seat mayaffect the performance of the front passenger sensing system.Determining if the system is o
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe
Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See yourauthorized dealer.All
The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuittha
Do not attempt to service, repair, or modify the Safety Canopy娂system, its fuses, the A, B, C or D pillar trim, or the headliner ona vehicle containin
• Rollover sensor in the restraints control module (RCM).The Safety Canopy娂 system, in combination with safety belts, can helpreduce the risk of sever
If the Safety Canopy娂 system has deployed, the SafetyCanopy娂 will not function again unless replaced. TheSafety Canopy娂 system (including the A, B, C,
require that children use approved booster seats until they are eightyears old. Check your local and state or provincial laws for specificrequirements
Booster seats position a child so that safety belts fit better. They lift thechild up so that the lap belt rests low across the hips and the kneesbend
• Those with a high back.If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo
Move a child to a different seating location if the shoulder beltdoes not stay positioned on the shoulder during use.Follow all instructions provided
• Place seat back in upright position.• Put the safety belt in the automatic locking mode. Refer to Automaticlocking mode (passenger side front and ou
AUDIO SYSTEMSAM/FM stereo/ single CD Satellite Compatible sound system(if equipped)Accessory delay: Your vehicle is equipped with accessory delay. Wit
1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly move the seat forwardand back to m
60/40 second row seatsDelivery vanFront passenger seating position (delivery van only)1. Position the child safety seat onthe passenger seat cushion.2
2. Route the child safety seat tetherstrap over the back of the seat. Ifthe head restraint is adjustable,route the tether strap under thehead restrain
If the tether strap is clippedincorrectly (as shown) thechild safety seat may not beretained properly in the event of acollision.5. Rotate the tether
Rear seating positionsFollow Steps 1–7 as described above for the following available seats:• 2nd row bucket (40/40)• 2nd row bench (60/40)• 3rd row b
Attaching safety seats with LATCH (Lower Anchors and Tethers forChildren) attachments for child seat anchorsNew child safety seats have two rigid or w
Each time you use the safety seat, check that the seat is properlyattached to the lower anchors and tether anchor. Try to tilt the childseat from side
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
2. Phone/mute: Press to mute theplaying media. Press again to returnto the playing media.3. Menu: Press to toggle throughthe following modes:CATEGORY
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
• Extra load: A class of P-metric or Metric tires designed to carry aheavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires].Increasing the
Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙blowout⬙,with unexpected loss of
Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo
Tire wearWhen the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Buil
2000 the numbers go to four digits. For example, 2501 means the 25thweek of 2001. The numbers in between are identification codes used fortraceability
Important: Remember to replace the wheel valve stems when the roadtires are replaced on your vehicle.It is recommended that the two front tires or two
Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Setting the clock: Press MENU until SELECT HOUR or SELECTMINUTE is displayed. Use/ to manually increase/decrease. PressMENU again to disengage clock m
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
11. Maximum Load: Indicates the maximum load in kilograms andpounds that can be carried by the tire. Refer to the Safety ComplianceCertification Label
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and ch
Vehicle Curb Weight – is the weight of your new vehicle when youpicked it up from your authorized dealer plus any aftermarketequipment.Payload – is th
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
Steps for determining the correct load limit:1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.
7. Shuffle: Press to play tracks inrandom order.8. Comp (Compression): In CDmode, brings soft and loud CDpassages together for a moreconsistent listen
calculation would be: 635 kg — (2 x 99 kg) — (12 x 45 kg) = 635 —198 — 540 = —103 kg. You will need to reduce the load weight by atleast 240 lb. (104
Preparing to towUse the proper equipment fortowing a trailer and make sure it isproperly attached to your vehicle.Use a trailer hitch with at leastthr
Trailer lampsTrailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working.
RECREATIONAL TOWINGFollow these guidelines for your specific powertrain combination to towyour vehicle for personal travel (such as behind a recreatio
STARTINGPositions of the ignition1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and a
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
• Make sure the gearshift lever is inP (Park).3. Turn the key to 3 (RUN) withoutturning the key to 4 (START).Some warning lights will briefly illumina
Guarding against exhaust fumesCarbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects.If you smell exhaust fumes i
keeping the brakes from locking. Noise from the ABS pump motor andbrake pedal pulsation may be observed during ABS braking and thebrake pedal may sudd
The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released.
Seating and Safety Restraints 113Seating 113Safety restraints 126Airbags 140Child restraints 154Tires, Wheels and Loading 169Tire information 169Tire
In Satellite Radio mode (if equipped), press SEEK to seek to theprevious channel. If a specific category is selected, (Jazz, Rock, News,etc.), pressto
The Traction Control娂 system will allow your vehicle to make better useof available traction on slippery surfaces. The system is a driver aidwhich mak
• Do not fill the power steering pump reservoir above the maximumlevel, as this may result in leaks from the reservoir. See Checking andadding power s
3. Locate the white plastic cover atthe front driver side of the gearshiftlever. Locate the screw whichattaches this cover and removeusing a screwdriv
As traditional automatic transmissions/transaxles shift up or down ingears, this shifting in gear ratios is noticeable by increasing anddecreasing eng
R (Reverse)With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Re
Certain add-on devices such as large trailer hitches, bike orsurfboard racks and any device that may block the normaldetection zone of the RSS system
If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement
If your vehicle goes off the edge of the pavement• If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ea
Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle (i.e.,
Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required f
Premium/Audiophile In-Dash Six CD/MP3 Satellite CompatibleSound System (if equipped)Accessory delay: Your vehicle is equipped with accessory delay. Wi
Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should
Driving on snow and iceNote: Excessive tire slippage can cause transaxle damage.AWD vehicles have advantages over 2WD vehicles in snow and ice butcan
DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
Canadian customers refer to your Owner Information Guide forinformation on:• coverage period• exact fuel amounts• towing of your disabled vehicle• eme
HAZARD FLASHER CONTROLThe hazard flasher is located on theinstrument panel by the radio. Thehazard flashers will operate whenthe ignition is in any po
FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth
Passenger compartment fuse panel/Smart Junction Box (SJB)The fuse panel is located under the instrument panel to the left of thesteering wheel.The fus
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionF8 15A Park lamps, Side markers, Trailertow protectF9 20A Cigar lighter, Da
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionF22 7.5A Auxiliary climate control relaycoils, Electrochromatic mirror,Comp
2. Phone/mute: Press to mute theplaying media. Press again to returnto the playing media.3. Menu: Press to toggle throughthe following modes:CATEGORY
The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 80A* SJB, SJB fuses 1, 2, 3, 4, 5, 8 an
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription14 20A** Power point (Cargocompartment)15 15A** Traction Control Module (TCM)16 20A**
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription39 1A Diode PCM40 1A Diode A/C clutch411⁄2ISO relay Fog lamps42 — Not used431⁄2ISO re
CHANGING THE TIRESIf you get a flat tire while driving:• do not brake heavily.• gradually decrease the vehicle’s speed.• hold the steering wheel firml
• Use more than one dissimilar spare tire at a time• Use commercial car washing equipment• Try to repair the dissimilar spare tireUse of one of the di
When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to:• Towing a trailer• Driving vehicles equipped with a
Tire change procedure1. Park on a level surface, activatehazard flashers and set the parkingbrake.When one of the front wheels is off the ground, the
3. Remove wheel cover (ifequipped) with the lug wrench tipand loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the
8. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torquespecifications later in this chapterfor the proper lu
4. Insert the straight end of the jackretention bracket through the eyeletof the angled bracket and swing theretention bracket over the jack. Withthe
Speed sensitive volume: Radio volume automatically changes slightlywith vehicle speed to compensate for road and wind noise.Use/ / SEEK to adjust. Rec
WHEEL LUG NUT TORQUE SPECIFICATIONSRetighten the lug nuts to the specified torque at 100 miles (160 km)after any wheel disturbance (tire rotation, cha
1. Use only a 12–volt supply to start your vehicle.2. Do not disconnect the battery of the disabled vehicle as this coulddamage the vehicle’s electric
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, flatbed transport vehicle or a car hauling trailer) yourvehic
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
Additional AssistanceIf you still have a complaint involving a warranty dispute, you may wishto contact the Better Business Bureau (BBB) AUTO LINE pro
5. Seek: In radio mode, press toaccess the next strong station.In CD mode, pressto access the next CD track.In Satellite Radio mode (if equipped), pre
In the case of 1 or 2 above, the consumer must also notify themanufacturer of the need for the repair of the nonconformity at thefollowing address:For
You can get more information by calling BBB AUTO LINE at1–800–955–5100, or writing to:BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia
You may purchase Ford ESP from any participating authorized dealer.There are several plans available in various time, distance and deductiblecombinati
If you buy your vehicle in North America and then relocate outside ofthe U.S. or Canada, register your vehicle identification number (VIN) andnew addr
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
WAXINGApplying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage.• Wash the ve
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:•Take care when u
WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub
Do not use chemical solvents or strong detergents when cleaningthe steering wheel or instrument panel to avoid contamination ofthe airbag system.• Be
12. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, press andhold a preset button until sound returns and PRESET # SAV
LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• To clean, use a soft cloth with Motorcraft
Motorcraft Dusting Cloth (ZC-24)Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20)Motorcraft Engine Shampoo (Canada only) (CXC-66-A)Motorcraf
SERVICE RECOMMENDATIONSTo help you service your vehicle we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column.2. Go to th
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.0L DOHC V6 DURATEC ENGINE1. Engine coolant reservoir2. Power steering fluid reservoir3. Brake fluid
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
CHANGING THE WIPER BLADES1. Pull the wiper arm away from the vehicle slightly.2. Press the release button and pull the wiper blade from the wiper arm.
5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.•
• If required, add engine oil to theengine. Refer to Adding engineoil in this chapter.• Do not overfill the enginewith oil. Oil levels above thismark
Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oil.Only use oils “Certified For Gasoline Engines” by t
17. CD: Press to enter CD mode. Ifa CD is already loaded into thesystem, CD play will begin where itended last.18. LOAD: Press to load a CD.Press LOAD
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If
Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyeswhen working near
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservo
To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. Thecooling system is under press
7. Pull off metal pin and removecoolant bleed plug from thethermostat housing.8. Add coolant/water mixturethrough the thermostat housingopening until
9. Install the thermostat housingbleed plug. Install metal pin bypushing into the slot.After any coolant has been added, check the coolant concentrati
Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut
FUEL FILTERFor fuel filter replacement, see your authorized dealer. Refer toscheduled maintenance information for the appropriate intervals forchangin
Don’t:• Expose discs to direct sunlight or heat sources for extended periodsof time.• Clean using a circular motion.CD units are designed to play comm
• Automotive fuels can be harmful or fatal if swallowed. Fuel such asgasoline is highly toxic and if swallowed can cause death or permanentinjury. If
RefuelingFuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others:• Read and follow all the instr
The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stopsbefore completely rem
Octane recommendationsYour vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofga
If you have run out of fuel:• You may need to cycle the ignition from OFF to ON several times afterrefueling to allow the fuel system to pump the fuel
• Use the same filling rate setting (low — medium — high) each timethe tank is filled.• Allow no more than two automatic click-offs when filling.• Alw
• Idling for long periods of time (greater than one minute) may wastefuel.• Anticipate stopping; slowing down may eliminate the need to stop.• Sudden
• Using fuel blended with alcohol may lower fuel economy.• Fuel economy may decrease with lower temperatures during the first8–10 miles (12–16 km) of
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
These temporary malfunctions can be corrected by filling the fuel tankwith good quality fuel and/or properly tightening the fuel cap. After threedrivi
• Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result in anaudio mute.Unli
1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center o
TRANSAXLE FLUIDChecking automatic transaxle fluid—CVT transaxleDo not use supplemental transaxle fluid additives, treatments orcleaning agents. The us
Replace the PCV valve with one that meets Ford material anddesign specifications for your vehicle, such as a Motorcraft orequivalent replacement part.
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItems CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationBrake fluidBetween MAXan
Items CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine coolant11.6 quarts(11.0L)Motorcraft Premium GoldEngine Coolant(yel
ENGINE DATAEngine 3.0L-DOHC V6 engineDisplacement 183 cubic inchesRequired fuel 87 octaneFiring order 1–4–2–5–3–6Spark plug gap (0.052–0.056 inch) 1.3
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for your vehiclethrough your local Ford or Ford of
LifestyleAsh cup / smoker’s packageCargo organization and managementPeace of mindMobile-Ease娂 hands free communication systemRemote startVehicle secur
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m
AAccessory delay ...74Air cleaner filter ...281Air conditioning ...48, 50, 52, 54Airbag supplemental r
washing ...245waxing ...246wheels ...246wiper bl
Foglamps ...59Four-Wheel Drive vehiclesdriving off road ...206Fuel ...
Keys ...109positions of the ignition ...194LLampsautolamp system ...58bulb replaceme
Relays ...216Remote entry system ...100–101illuminated entry ...105locking/unlocking doors .
tire grades ...170treadwear ...169, 174Towing ...190recreational
296
Maintenance and Specifications 252Engine compartment 254Engine oil 256Battery 260Engine coolant 262Fuel information 269Part numbers 281Maintenance pro
Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The
FAMILY ENTERTAINMENT DVD SYSTEM (IF EQUIPPED)Your vehicle may be equipped with a Family Entertainment DVD Systemwhich allows you to play commercial DV
4. ENTER controlPress to select the function highlighted on the active menu. ENTER mayalso be used by some user interactive discs during movie play.5.
• Press the PREV control to movethe cursor one position downward• Press the REV control to movethe cursor left one position• Press the FWD control to
CD play modePress NEXT during CD play toadvance to the next track. If youpress NEXT while the last track isplaying, the system will wrap aroundto the
Remote control1. REV (REVERSE) controlPress to reverse the direction of the DVD movie.2. FWD (FORWARD) controlPress to advance the direction of the DV
7. MENU/MODE controlIn DVD playback mode, press to access the disc menu.In stop mode, press to change media types (e.g. AM, FM, CD...)8. VOL (VOLUME)
Battery replacementBatteries are provided with the remote control unit. Since all batterieshave a limited shelf life, replace them when the remote con
Wireless headphone operationTo operate the headphones:• Press the ON/OFF button on theearpiece to turn on theheadphones. A red LED(indicator light) wi
Liquid Crystal Display (LCD) flip-down screenThe LCD screen rotates down and can be adjusted to your desired viewingangle. When not in use, rotate the
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
• Always save MP3 files with the .mp3 extension. The player recognizesan MP3 file by the .mp3 extension, so MP3 files saved with differentextensions w
This unit is designed to play commercially pressed 4.75 (12 cm)audio compact discs and DVDs only. Due to technicalincompatibility, certain recordable
On-screen indicatorsEach time a control is pressed, the operational status of the DVD playeris shown on the screen. The following are some possible in
The front glass on the flip-down liquid crystal display (LCD) maybreak when hit with a hard surface. If the glass breaks, do nottouch the liquid cryst
However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interferenceto radio
Foreign substancesExercise care to prevent dirt and foreign objects from entering the DVDplayer compartment. If liquid is accidentally spilled onto th
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
6. Fan speed adjustment: Controls the volume of air circulated in thevehicle.Operating tips• To reduce fog build up on the windshield during humid wea
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED)1.Defrost: Distributes outside air through the windshield defrosterand demister vents. Can be used
8. : Distributes air through the instrument panel and floor vents.9.: Distributes air through the instrument panel vents.10. Manual override controls:
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
Dual Zone Automatic Temperature Control with heated seats(if equipped)1.Defrost: Distributes outside air through the windshield defrosterand demister
7. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. Engagesautomatically in
Dual Zone Automatic Temperature Control with rear passengercompartment climate control (if equipped)1.Defrost: Distributes outside air through the win
odors from reaching the interior of the vehicle. Recirculation can beengaged manually in any other airflow selection except defrost.Recirculation may
Dual Zone Automatic Temperature Control with heated seats andrear passenger compartment climate control (if equipped)1.Defrost: Distributes outside ai
indicator light), and press again to deactivate the passenger heated seat.Note: The heated seat feature will remain on for approximately tenminutes.7.
15. F/C (Temperature conversions): Press to switch temperaturedisplay between ° Fahrenheit and ° Celsius.16. OFF: Outside air is shut out and the clim
To aid in side window defogging/demisting in cold weather:1. Select.2. Select A/C.3. Adjust the temperature control to maintain comfort.4. Set the fan
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola
5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamp switch to. The headlampswill turn off.Fogl
SPECIAL NOTICESNew Vehicle Limited WarrantyFor a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited
Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the ON position,• the head
• (1) 8 feet (2.4 meters)• (2) Center height of lamp toground• (3) 25 feet (7.6 meters)• (4) Horizontal reference line2. Measure the height of thehead
TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSDome lamps and map lampsThe ma
Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an
3. Locate the outboardmostelectrical connector and remove itby releasing the locking tab andpulling it off.4. Remove the bulb socket byturning it coun
3. Locate the front sidemarker lampelectrical connector and remove itby pulling it off.4. Remove the bulb socket byturning it counterclockwise andpull
Replacing high-mount brake lamp bulbs1. Make sure the ignition control isin the OFF position.2. Remove the two screws.3. Unclip the bulb holder from t
MULTI-FUNCTION LEVERWindshield wiper: For intermittentoperation, move control up oneposition.Adjust the rotary control to thedesired speed setting.Mis
Rear window wiper/washer controlsFor rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select:2 — Three to f
ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamp. The visor willslide back and forth on the rod forincrease
• where the driver was positioning the steering wheel.To access this information, special equipment must be directly connectedto the recording modules
Storage compartmentPress the latch to open the storagecompartment. The door will openslightly and can be moved to fullopen.The storage compartment may
Second row center console features (if equipped)The second row center consoleincorporates the following features:• Utility compartment• Cupholders• Fl
Do not hold the lighter in with your hand while it is heating, this willdamage the lighter element and socket. The lighter will be released fromits he
To operate ONE TOUCH UP:• Pull the switch completely up tothe second detent and releasequickly. The driver’s window willclose fully. Momentarily press
Accessory delayWith accessory delay, the radio, Family Entertainment DVD System (ifequipped), power windows, and moonroof (if equipped) operate for up
Fold-away mirrorsPull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.Heated outside mirrors(if equipped)B
Memory feature (if equipped)The accelerator and brake pedal positions are saved when doing amemory set function and can be recalled along with the veh
Note:• Vehicle speed may vary momentarily when driving up and down asteep hill.• If the vehicle speed increases above the set speed on a downhill, you
Reducing speed while using speed controlThere are two ways to reduce a setspeed:• Press and hold the SET - controluntil you get to the desiredspeed, t
STEERING WHEEL CONTROLS (IF EQUIPPED)Radio control features• Press MEDIA to select AM, FM1,FM2, or CD (if equipped).In Radio mode:• Press SEEK to acce
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
MOON ROOF (IF EQUIPPED)You can move the glass panel of the moon roof back to open or tilt up toventilate the vehicle.Do not let children play with the
HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED)The HomeLink威 Wireless ControlSystem, located on the driver’s visor,provides a convenient way toreplace
1. Press and hold the two outsidebuttons releasing only when theindicator light begins to flash after20 seconds. Do not repeat Step 1to program additi
7. Press and release the “learn” or “smart” button. (The name and colorof the button may vary by manufacturer.)Note: There are 30 seconds in which to
Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet
MESSAGE CENTER (IF EQUIPPED)With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle info
The DTE function will display LOW FUEL LEVEL and a single tone whenyou have approximately 50 miles (80 km) to empty. If you RESET thiswarning message,
Trip elapsed drive timeSelect this function from the INFOmenu to display a timer.To operate the Trip Elapsed DriveTime perform the following:1. Press
Note: If message center displays the message ⬙SLOW CIRCLES TOCALIBRATE⬙, then perform the CALIBRATION PROCEDURE.4. Determine your magnetic zone byrefe
Note: If message center displays the message ⬙SLOW CIRCLES TOCALIBRATE⬙, then continue with Step 4. Otherwise, if a heading isdisplayed, continue with
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
3. Press and hold the RESETcontrol to set the language choice.Units (English/Metric)1. Select this function from theSETUP menu for the current unitsto
System warningsSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems.In the event of a multiple warning si
PASSENGER DOOR AJAR. Displayed when the passenger side door isnot completely closed.LEFT REAR DOOR AJAR. Displayed when the left rear door is notcompl
To reset the oil monitoring system to 100% after each oil change[approximately 5,000 miles (8,000 km) or 180 days] perform thefollowing:To reset the o
3. Press and hold RESET controlagain until OIL LIFE SET TO 100%is displayed. Your oil life is nowreset.LIFTGATEUnlock the liftgate (but do notrelease
CARGO AREA FEATURESCargo net (if equipped)The cargo pouch net secureslightweight objects in the cargoarea. Attach the net to the anchorsprovided. Do n
To adjust the cross-bar (if equipped) position:1. Loosen the thumbwheel at bothends of the cross-bar.2. Slide the cross-bar to the desiredlocation.3.
KEYSOne key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency.Your keys are programmed to your v
The autolock feature repeats when:• any door or the liftgate is opened then closed while the ignition is inthe 3 (RUN) position, and• you put the vehi
5. Release the 3 • 4.6. Release the 7 • 8.The user should receive a horn chirp to indicate the system has beendisabled or a chirp followed by a honk t
Commentaires sur ces manuels