Introduction 4Instrument Cluster 10Warning lights and chimes 10Gauges 16Entertainment Systems 19AM/FM stereo 19AM/FM stereo with CD 21AM/FM stereo cas
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
• activate the personal alarm.• arm and disarm the perimeter anti-theft system (if equipped).If there are problems with the remote entry system, make
Opening power liftgate (PLG) (if equipped)Press the control twice within three seconds to power open the powerliftgate. The interior lamps will illumi
If any of the doors, the liftgate or the hood (if equipped with perimeteralarm) are not properly closed, the horn will make two quick chirps andthe pa
Replacing the batteryThe remote entry transmitter uses one coin type three-volt lithiumbattery CR2032 or equivalent.To replace the battery:1. Twist a
Replacing lost remote entry transmittersIf you would like to have your remote entry transmitter reprogrammedbecause you lost one, or would like to buy
Illuminated entryThe interior lamps illuminate when the key in the driver’s door lockcylinder (if equipped with perimeter alarm), the keyless entry sy
The system will automatically turn off if:• the vehicle is locked using the remote entry system, the keyless entrykeypad, or• the ignition is turned t
KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to:• lock or unlock the doors without using a key.• activate or deactivate the a
• Press 1 • 2 to recall the Driver 1 position.• Press 3 • 4 to recall the Driver 2 position.5. After five seconds of keypad inactivity, programming mo
To open (or close) the power sliding doors (if equipped), press the5 • 6 control within five seconds to open (or close) the left powersliding door or
Check engine: The Check Engineindicator light illuminates when theignition is first turned to the ONposition to check the bulb and toindicate whether
If any of these items are present, you need to prevent these objects fromtouching the coded key while starting the engine. These objects cannotdamage
1. Insert the first previouslyprogrammed coded key into theignition and turn the ignition fromthe 3 (OFF) position to the 4 (ON)position [maintain ign
PERIMETER ALARM SYSTEM (IF EQUIPPED)The perimeter anti-theft system will warn you in the event of anunauthorized entry to your vehicle.If there is any
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Push control to lower head restraint.Adjusting the front manual seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback.After returning the sea
To reduce the risk of possible serious injury: Do not hang objectsoff seat back or stow objects in map pocket (if equipped) whena child is in the fron
Heated seats (if equipped)To operate the heated seats:• Push the control located on theclimate control system panel onceto activate high heat.• Push t
REAR SEATSHead restraintsLift the head restraint so that it is located directly or as close as possiblebehind your head.The head restraints can be mov
The cupholder is designed to detach from the seat when subjected toheavy load. The cupholder can be reinstalled by returning to the closedposition.Use
Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance mayoccur. It will take you longer
• 2nd row bench seat (if equipped)Note: This seat can be movedforward to keep a child in aLATCH child restraint attachedto the LATCH anchors at thecen
Accessing the third row seat with a second row bucket seatEnsure head restraint is in the fulldown position and seat is adjustedto full rear position
Continuing to lift the handle willtumble the seat forward, allowingeasier access to the third row seat.After entering the 3rd row seat,return the seat
• Ensure that the seat and seatback is latched securely in position.• Keep floor area free of objects that would prevent proper seatengagement.• Do no
After entering the 3rd row, pull backthe seatback until it latches. Thiswill latch and lock the seatback andthe seat track. The seatback andseat will
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped underneath theseatback. After returning the
5. Rotate the seat rearward at a 30to 45 degree angle.6. With the assist handle, pull theseat rearward.7. Remove the seat from vehicle.Second row benc
2. Find the clips attached near theends of the lap/shoulder belts.3. Clip the end of the belt to thestationary portion of the shoulderbelt coming out
4. Position seatback in full downposition.5. From behind seat pull straightback on the release handles locatedon each side of the seat, releasingthe r
2. Install seat onto rear pin of fronttub at a 30 to 45 degree angle.3. Rotate the seat forward until itlatches onto the front pin.4. Rotate seat rear
Engine coolant temperature:Illuminates when the engine coolanttemperature is high. Stop thevehicle as soon as possible, switch off the engine and let
5. Operate recline lever and pushthe seat back upright.Ensure seat is latched to vehicle floor by pushing/pulling on seat.If not latched, the seat may
3. Lower back of seat onto the reartubs until both release controls latchinto place. Be sure that the seat islocked in place both front and back.Do no
2. If you plan to carry very largeobjects or items that might damagethe center lap/shoulder belt, detachthe belt from the seat. Use a key orsafety bel
4. Store the belt in the housingfound on the ceiling by inserting thesmaller tongue in the slot provided.Note: The seat can be stowed withthe safety b
6. From the rear of the vehicle, fold seat back by pulling and releasingthe number 1 strap.Important: If you don’t let go ofthe number 1 strap before
8. Pull the number 3 strap on the seat back to tumble seat all the way into the tub in the floor.Do not use the seat anchors as cargo tie downs.Unstow
2. To return the seat back to theseating position, pull the number 1strap, then while holding thenumber 1 strap, pull the number 3strap to raise the s
Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a collision.Ta
3. To return the seat, ensure seatlatching area is free of objects.Then, raise the seat off the liftgatescuff plate and push at the top ofthe seat bac
How does the Personal Safety System姟 work?The Personal Safety System娂 can adapt the deployment strategy of yourvehicle’s safety devices according to c
Speed control: Illuminates whenthe speed control is engaged. Turnsoff when the speed control systemis disengaged.Low washer fluid: Illuminates when th
Front passenger sensing systemFor airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occu
Front safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly ag
Safety belt precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injury, mak
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of l
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could re
Safety belt extension assemblyIf the safety belt is too short when fully extended,a9inch(23cm)or12 inch (31 cm) safety belt extension assembly can be
Failure to inspect and if necessary replace the safety beltassembly under the above conditions could result in severepersonal injuries in the event of
Both the driver’s and passenger’s safety belt usages are monitored andeither may activate the Belt-Minder威 feature. The warnings are the samefor the d
Bulb warning: Illuminates when one of the exterior front turn lamps orrear brake/turn/tail lamps bulb has burned out.• Without Message Center• With Me
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate
• The ignition switch is in the OFF position• The driver and front passenger safety belts are unbuckledWhile the design allows you to deactivate your
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The airbag supplemental restraint system (SRS) is designed to work inconjunction with the safety belts to he
Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.The National Highway Traffic Saf
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
• one or more impact and safing sensors.• Safety belt pretensioner• a readiness light and tone.• diagnostic module.• and the electrical wiring which c
For side airbag equipped vehicles, the front passenger sensing systemwill turn off the passenger seat side airbag if:• the seat is empty and safety be
• Have the person sit upright in the seat, centered on the seat cushion,with the person’s legs comfortably extended.• Restart the vehicle and have the
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. 3 ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase, ful
In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi
A difficulty with the system is indicated by one or more of the following:• The readiness light (same lightfor front and side airbag system)will eithe
Group. These recommended testing procedures help reduce the risk ofinjuries related to the deployment of side airbags.The front passenger sensing syst
Several air bag system components get hot after inflation. Do nottouch them after inflation.If the side airbag hasdeployed, the airbag willnot functio
All occupants of the vehicle including the driver should alwayswear their safety belts even when an airbag SRS and SafetyCanopy娂 system is provided.To
Children 12 years old and under should always be properly restrained inthe second or third row seats. The Safety Canopy娂 will not interferewith childr
Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref
Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.Alwa
When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the
Odometer: Registers the total miles (kilometers) of the vehicle.• Without Message CenterTo switch the display from Metric toEnglish, press and hold th
• Those with a high back.If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo
The importance of shoulder beltsUsing a booster without a shoulder belt increases the risk of a child’shead hitting a hard surface in a collision. For
When installing a child safety seat:• Review and follow the informationpresented in the AirbagSupplemental Restraint Systemsection in this chapter.• U
Installing child safety seats with combination lap and shoulderbeltsAirbags can kill or injure a child in a child seat. NEVER place arear-facing child
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat.
The tether anchors in your vehicleare in the positions shown:The front passenger seat with power adjustment does not have atether anchor. The two teth
2. Route the child safety seat tetherstrap over the back of the seat. Ifthe head restraint is adjustable,route the tether strap under thehead restrain
If the tether strap is clippedincorrectly (as shown) thechild safety seat may not beretained properly in the event of acollision.5. Rotate the tether
Rear seating positionsFollow Steps 1–7 as described above for the following available seats:• 2nd row bucket• 2nd row bench• 3rd row benchFor addition
Tachometer: Indicates the enginespeed in revolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the
Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol.If your vehicle has a second rowb
Follow the child seat manufacturer’s instructions to properly install achild seat with LATCH attachments.Attach LATCH lower attachments of the child s
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙blowout⬙,with unexpected loss of
Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo
Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of thetire to set the beads without ad
AUDIO SYSTEMSAM/FM stereo system (if equipped)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various set
If your vehicle is stuck in snow, mud, sand, etc., do not rapidlyspin the tires; spinning the tires can tear the tire and cause anexplosion. A tire ca
• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can be corrected by rotating the tires.Note: If your tir
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
Changing tires with TPMSEach road tire is equipped witha tire pressure sensor fastenedto the inside rim of the wheel.The pressure sensor is coveredby
When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.
Seating and Safety Restraints 113Seating 113Safety restraints 138Airbags 153Child restraints 167Tires, Wheels and Loading 182Tire information 182Tire
3. Seek: Press to access thenext/previous strong station ortrack.4. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, pr
Low Tire PressureWarning LightPossible cause Customer Action RequiredFlashing WarningLightSpare tire in use Your temporary spare tire is inuse. Repair
any tire is under-inflated, carefully drive the vehicle to the nearestlocation where air can be added to the tires. Inflate all the tires to therecomm
VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic
The appropriate loading capacity of your vehicle can be limitedeither by volume capacity (how much space is available) or bypayload capacity (how much
Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue loadweight is als
GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).
Maximum Loaded Trailer Weight – is the highest possible weight of afully loaded trailer the vehicle can tow. It assumes a vehicle with onlymandatory o
The following gives you a few examples on how to calculate the availableamount of cargo and luggage load capacity:• Another example for your vehicle w
TRAILER TOWINGYour vehicle is capable either of towing Class I trailers or up to Class IItrailers when equipped with the optional trailer tow package.
Vehicle towing capability/Trailerhitch requirementTrailerModel/EngineGCWR -lb. (kg)Hitch typerequiredTrailerWeight range- lb. (kg)Tongue loadVan, 3.9L
AM/FM stereo/ single CD sound system (if equipped)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various
HitchesDo not use hitches that clamp onto the vehicle bumper. Use a loadcarrying hitch that does not exceed your vehicle’s capability. See theTongue L
Driving while you towWhen towing a trailer:• Keep your speed no faster than 70 mph (112 km/h) during the first500 miles (800 km) of towing a trailer,
RECREATIONAL TOWINGFollow these guidelines for your specific powertrain combination to towyour vehicle with all four wheels on the ground (such as beh
STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
• Turn the key to 4 (ON) withoutturning the key to 5 (START).Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrume
Important ventilating informationIf the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least one inch (2.
ABS warning lampThe ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringsta
Parking brakeTo set the parking brake, pull thehandle up as far as possible. TheBRAKE warning lamp will illuminateand will remain illuminated until th
• Maneuvering quickly to avoid an accident, pedestrian or obstacle• Hitting a patch of ice• Changing lanes on a snow-rutted road• Entering a snow-free
Treble: Press to adjust the treble setting. Use / / SEEK .Balance: Press to adjust the audio between the left and right speakers.Use/ / SEEK .Fade: Pr
• A slight deceleration of the vehicle• The AdvanceTrac威 indicator light will illuminate• If your foot is on the brake pedal, you will feel a vibratio
• Heavy or uneven steering efforts may be caused by a low powersteering fluid level. Check for a low power steering fluid level beforeseeking service
When the key is in the ignition and in the 3 (OFF) position, theautomatic transmission shift lever can be moved from the P(Park) position without the
Understanding the gearshift positions of the 4–speed automatictransaxleP (Park)This position locks the transaxle and prevents the front wheels fromtur
1 (First)• Transaxle operates in first gear only.• Provides maximum engine braking.• Allows upshifts by moving gearshift lever.• Will not downshift in
To help avoid personal injury, always use caution when in R(Reverse) and when using the RSS.This system is not designed to prevent contact with small
The RSS is automatically enabledwhen the gear selector is placed inR (Reverse) and the ignition is ON.The park aid disable switch allowsthe driver to
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsUsing roadside assistanceComplete the roadside assi
FUEL PUMP SHUT-OFF SWITCHThis device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt.After an
10. Fast forward: Press tomanually advance in a CD track.11. Rewind: Press to manuallyreverse in a CD track.12. Memory presets: To set astation: Selec
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 Relay Accessory delay relay 12 Relay Acces
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description12 5A Brake-Shift Interlock (BSI) Runfeed, Climate control system Runfeed13
Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot
The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 — Not used2 30A** Right cooling fan3 30
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription32 Mini relay Rear defroster40 15A* Engine #1 (A/C relay coil, IMRC,HEGO sensors, Can
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription61 — Not used62 30A* SJB #3 – Right cornering/auxiliarylamps, Right low beam, Left fr
Auxiliary relay box (cooling fans)The relay box is located in the engine compartment by the radiator.Fuse/RelaylocationFuse ampratingDescription1 — Co
The use of tire sealants may damage your tires. The use of tiresealants may also damage your Tire Pressure Monitoring Systemand should not be used.You
• Try to repair the dissimilar spare tireUse of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the
AM/FM stereo cassette/single CD sound system (if equipped)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select
Drive cautiously when using a full-size dissimilar spare tire/wheel andseek service as soon as possible.Location of the spare tire and toolsNote: The
Removing the spare tire1. Wagon only: Open liftgate andlift flap in the carpeting on the reartub cargo floor to expose the hexnut. Insert the lug nut
Tire change procedureWhen one of the front wheels is off the ground, the transaxlealone will not prevent the vehicle from moving or slipping off theja
3. Remove the spare tire, jack and lug wrench.4. Removing the optional wheelcover or center ornament:• To remove a bolt-on wheel cover(if equipped) lo
If Ford Accessory Running Boardshave been installed, use the jackadapters supplied with the runningboards as described on the inside ofthe jack storag
11. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lug nuttorque specifications later in thischapter for the proper l
3. Lay the tire flat and secure the cable with wing screw by installing iton the wing screw retainer in the floor and turning the wing screwclockwise.
WHEEL LUG NUT TORQUE SPECIFICATIONSRetighten the lug nuts to the specified torque at 500 miles (800 km)after any wheel disturbance (rotation, flat tir
1. Use only a 12–volt supply to start your vehicle.2. Do not disconnect the battery of the disabled vehicle as this coulddamage the vehicle’s electric
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
Fade: Press to adjust the audio between the front and rear speakers.Use/ / SEEK .Speed sensitive volume (if equipped): Radio volume automaticallychang
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
Additional AssistanceIf you still have a complaint involving a warranty dispute, you may wishto contact the Better Business Bureau (BBB) AUTO LINE pro
In the case of 1 or 2 above, the consumer must also notify themanufacturer of the need for the repair of the nonconformity at thefollowing address:For
You can get more information by calling BBB AUTO LINE at1–800–955–5100, or writing to:BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia
You may purchase Ford ESP from any participating authorized dealer.There are several plans available in various time, distance and deductiblecombinati
If you buy your vehicle in North America and then relocate outside ofthe U.S. or Canada, register your vehicle identification number (VIN) andnew addr
9. Compress (Compression): InCD mode, brings soft and loud CDpassages together for a moreconsistent listening level.10. Repeat: Press to repeat thecur
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is
WAXINGApplying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage.• Wash the ve
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub
• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to a
Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing.Do not use chemical solvents or
FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th
19. CD eject: Press to eject a CD.20. CD slot: Insert a CD label sideup.21. Seek:Press to access theprevious strong station or track.22. Scan: Press f
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.9L/4.2L V6 engines1. Brake fluid reservoir2. Air filter assembly3. Power distribution box4. Battery5
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
CHANGING THE WIPER BLADESTo replace the wiper blades:1. Pull the wiper arm away from thewindshield and lock into the serviceposition.2. Turn the blade
5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.•
• Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine isoverfilled, some oil must beremoved from the e
economy requirements of the International Lubricant Standardization andApproval Committee (ILSAC), comprised of U.S. and Japaneseautomobile manufactur
It is recommended that the negative battery cable terminal bedisconnected from the battery if you plan to store your vehicle for anextended period of
Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe bat
ENGINE COOLANTChecking engine coolantThe concentration and level of engine coolant should be checked at theintervals listed in scheduled maintenance i
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
1. / Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various settings.2. Phone/mute: Press to mute theplaying
Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservo
For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when
Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium
• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i
Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforerefueling your vehicle.• Al
RefuelingFuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others:• Read and follow all the instr
If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any
Octane recommendationsYour vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofga
If you have run out of fuel:• You may need to cycle the ignition from OFF to ON several times afterrefueling to allow the fuel system to pump the fuel
For consistent results when filling the fuel tank:• Turn the engine/ignition switch to the off position prior to refueling,an error in the reading wil
4. Aux: Press to toggle betweenFES/DVD and AUX modes. If noauxiliary sources are available, NOAUX AUDIO will be displayed.5. Seek: Press to access the
Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin
Conditions• Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed.• Carrying unnecessary weight may reduce fuel economy (a
• Do not turn off the ignition while your vehicle is moving, especially athigh speeds.• Have the items listed in scheduled maintenance informationperf
On board diagnostics (OBD-II)Your vehicle is equipped with a computer that monitors the engine’semission control system. This system is commonly known
If the indicator is on or the bulb does not work, the vehicle mayneed to be serviced. Refer to the On board diagnostics (OBD-II)description in this ch
3. Turn the engine off.4. Check the fluid level in the reservoir. It should be between the MINand MAX lines. Do not add fluid if the level is within t
4. Latch the gearshift lever in P (Park) and leave the engine running.5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. Ifneces
Use of a non-approved automatic transmission fluid may causeinternal transaxle component damage.If necessary, add fluid in 1/2 pint (250 mL) increment
Reposition the locking clip (on theconnector) and squeeze connectorto remove.2. Loosen the hose clamp locatedclosest to the air cleaner.3. Remove the
4. Release the two clamps thatsecure the cover to the air filterhousing and place the cover aside.5. Remove the air filter elementfrom the air filter
Maintenance and Specifications 268Engine compartment 270Engine oil 272Battery 275Engine coolant 278Fuel information 283Air filter(s) 297Part numbers 3
16. ON/OFF/Volume: Press to turnON/OFF. Turn to increase/decreasevolume.If the volume is set above a certainlevel and the ignition is turned off,the v
8. Replace the air filter housingcover and secure the clamps. Besure all the tabs on the bottom edgeare properly aligned.9. Reinstall the air cleaner
10. Ensure the pads on the bottomof the air cleaner assembly areproperly seated.11. Reconnect the outlet tube to theair cleaner assembly and tighten t
MOTORCRAFT PART NUMBERSComponent 3.9L OHV V6 engine 4.2L OHV V6 engineAir filter element FA-1679 FA-1679Battery BXT-59 BXT-59BXT-65-750 BXT-65-750Fuel
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationBrake fluidFill to MAX lineon reservo
Item Capacity Ford part nameFord part number /Ford specificationLock cylinders —Motorcraft Penetrating andLock LubricantXL-1 /NonePower steering fluid
ENGINE DATAEngine 3.9 L OHV V6 engine 4.2L OHV V6 engineCubic inches 232 256Required fuel 87 octane 87 octaneFiring order 1-4-2-5-3-6 1-4-2-5-3-6Ignit
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
Peace of mindMobile-Ease娂 hands-free communication systemRemote startVehicle security systemsWheel locksNot all accessories are available for all mode
1. Volume: Press to /increase/decrease volume control.2. Media: Press to select fromdifferent playing medias.3./ : Press to activate dualplay mode and
AAccessory delay ...68AdvanceTrac ...218Air cleaner filter ...297, 302Air filter, cabin
wiper blades ...264Clock ...66Compass, electronic ...58calibration
capacity ...303choosing the right fuel ...286comparisons with EPA fueleconomy estimates ...291de
headlamps, flash to pass ...46instrument panel, dimming ...47interior lamps ...49–51replacing bulbs ...53,
Roadside assistance ...227Roof rack ...92SSafety Belt Maintenance ...147Safety belts (see Safe
fluid, refill capacities ...303lubricant specifications ...303Transmissionbrake-shift interlock (BSI) ...221fluid, checking and add
316
317
318
319
Dual play modePress/ on the rear seat audiocontrols or simultaneously press theradio preset controls 2 and 4 toenable/disable dual play.During dual pl
320
Cassette/player careDo:• Tighten very loose tapes by inserting a pen or pencil into the hole andturning the hub.• Remove loose labels before inserting
CD units are designed to play commercially pressed 4.75 in(12 cm) audio compact discs only. Due to technicalincompatibility, certain recordable and re
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
Dual zone manual heating and air conditioning system with rearpassenger compartment climate control (if equipped)1. Air flow selections: Controlsthe d
will be warmer or cooler than the driver airflow temperature settingwhen more than one rear temperature light (REAR )isilluminated.5.RRear defroster:
In the and modes:• Move the temperature control selector to the coldest setting.• Select A/C and recirculated air. Use with A/C to providecolder airfl
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH REARPASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED)1.Defrost: Distributes outside air through the win
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
6. Recirculated air: Press to activate/deactivate air recirculationin the vehicle cabin. Recirculated air may reduce the amount of time tocool down th
Dual zone automatic temperature control with heated seats andrear passenger compartment climate control (if equipped)1.Defrost: Distributes outside ai
7. :Distributes air through the windshield defroster vents and thefloor vents.8.: Distributes air through the floor vents.9.: Distributes air through
Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
AUXILIARY CLIMATE CONTROL (IF EQUIPPED)1. Fan speed: Turn to select thedesired fan speed.2. Temperature/mode selection:The distribution of air from th
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Note:
To program the auto lamp exit time delay:1. Start with the ignition in the OFF position and the headlamp controlin the autolamp position.2. Deselect t
Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Light (DRL) Systemdoes not activate your tail lamps
The dome lamp will not illuminate if the control switch is not rotatedpast the detent.AIMING THE HEADLAMPSThe headlamps on your vehicle are properly a
5. Locate the vertical adjuster oneach headlamp, then usea#2Phillips screwdriver to turn theadjuster either counterclockwise (toadjust up) or clockwis
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
Map lamps (if equipped)The map lamps and controls arelocated on the center overheadconsole. Press the raised portion oneach lens to activate the lamps
The dome lamp will illuminate whenever a front door is opened. If eitherfront door has been opened from the outside, the lamp will remain on for20 sec
Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an
Replacing headlamp bulbsTo remove the headlamp bulb:1. Make sure headlamp switch is in the OFF position, then open thehood.2. Remove the two retainer
3. To remove the side marker bulb,turn the bulb socketcounterclockwise, and pull the bulbstraight out of the socket.4. To remove the parking/turnbulb,
Replacing license plate lamp bulbThe license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT STEERING WHEELTo adjust the steering wheel:1. Pull and hold the steering wheelrelease control toward you.2. Move the steering wheel up ordown unt
OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehicle’s overhead console will vary according toyour option package.Conversation mirrorThe conve
The compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antenna. Magneticor metallic objec
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Airbag supplemental re
Compass calibration mode1. Press the momentary push buttonand hold it for more than 8 seconds.After 8 seconds, CAL is displayed,then release it.Note:
If the door is allowed to slide open or closed unrestrained,personal injury or damage to the door could result.When closing the sliding door, keep the
Power Sliding Door (PSD) (if equipped)With this option, you can open and close the sliding door(s) with thefollowing controls inside your vehicle.• ov
To power open or close the PSDfrom the second row passengercontrol switch:• Ensure that the PSD is unlocked,using the remote entrytransmitter or power
desirable to prevent power operation of the door by rear seat passengersor if manual operation of the door is desired or necessary when thevehicle is
8. Remove the PSD fuse (fuse #11) from the passenger fuse panel andleave it out for thirty (30) seconds. Refer to the chapter on Fuses andRelays. Refe
CLOCK (IF EQUIPPED)Press the right (+) control to movethe time display forwards.Press the left (-) control to movethe time display backwards.AUXILIARY
• Located next to the second rowseat.• Located on the right trim panel inthe rear cargo area.Cigar/Cigarette lighter (if equipped)Do not plug optional
Press and pull the window switchesto open and close windows.• Push down (to the first detent)and hold the switch to open.• Pull up (to the first deten
The power vent windows areoperated by a single switch locatedon the instrument panel. Press andhold the bottom of the switch toopen or the top of the
To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access e
Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re
POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is
3. Press the SET + control andrelease it.4. Take your foot off the acceleratorpedal.5. The indicatorlight on theinstrument cluster will turn on.Note:•
• Use the accelerator pedal to get to the desired speed. When thevehicle reaches that speed press and release the SET + control.Reducing speed while u
STEERING WHEEL CONTROLS (IF EQUIPPED)Radio control features• Press MEDIA to select AM, FM1,FM2, TAPE or CD (if equipped).In Radio mode:• Press SEEK to
When programming your HomeLink威 Wireless Control System toa garage door or gate, be sure that people and objects are out ofthe way to prevent potentia
3. Simultaneously press and holdboth the chosen HomeLink威 andhand-held transmitter buttons untilthe HomeLink威 indicator lightchanges from a slow to a
Gate Operator & Canadian ProgrammingDuring programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time for
Erasing HomeLink姞 buttonsTo erase the three programmedbuttons (individual buttons cannotbe erased):• Press and hold the two outerHomeLink威 buttons unt
Info menuThis control displays the followingoptions:• Odometer• Distance to Empty• Trip Odometer• Average Fuel Economy• Trip Elapsed Drive Time• Displ
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
• variations in top-off procedure from one fill-up to another• rounding of the displayed values to the nearest 0.1 gallon (liter)1. Drive the vehicle
Language1. Select this function from theSETUP menu for the currentlanguage to be displayed.2. Pressing the RESET controlcycles the message center thro
Pressing the RESET control cycles the message center through each ofthe systems being monitored and will display the following only whenthere is a mal
Warning display StatusDriver’s door ajar Warning cannot be resetPassenger door ajarLeft rear door ajarRight rear door ajarPark brake set Warning retur
CHECK BRAKE LAMPS. Displayed when the brake lamps areactivated and at least one is burned out. Check the lamps as soon aspossible and have the burned
To reset the oil monitoring system to 100% after each oil change[approximately 5,000 miles (8,000 km) or 180 days] perform thefollowing:1. Press the S
2. Press and release the RESETcontrol to display “OIL LIFE XX%HOLD RESET NEW”.3. Press and hold the RESETcontrol for 2 seconds to display “IFNEW OIL H
POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)Do not install additional floor mats on top of the factory installedfloor mats as they may interfere with th
POWER LIFTGATE (PLG) (IF EQUIPPED)With this option, you can power open or close the liftgate with theprovided controls.• overhead console button• remo
The Power Door Lockout Control islocated in the overhead console.With the control in the OFFposition, power operation is disabledfrom the liftgate han
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
Note: Continued force applied after unlatching may activate the obstacledetection feature and stop the power system. For the best performanceallow the
If any of these conditions occur, the PLG must be reset. To reset thePLG:1. Manually close and fully latch the liftgate.2. Power open the liftgate by
Utility hooksThe utility hooks can be used tohang small items. Do not hang morethan 20 lb. (12 kg) on each of thehooks. The hooks are not designedto r
To remove the cross-bar assembly (if equipped):1. Remove rear support covers fromthe rear rails. Place a small objectinto the pin holes and slide thec
To reinstall the cross-bar assembly (if equipped):1. Slide the cross-bar into the railtrack with the arrow facing towardsthe front of the vehicle. Sli
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
1. Locate the liftgate trim accesspanel in the center of the liftgate.2. Using your key, a smallscrewdriver or knife, pry off theaccess panel.3. Using
RelockThe autolock feature repeats when:• an “autolock” occurrence has already taken place,• the brake is depressed while vehicle speed is less than 5
4. Press the power door unlock control three times.5. Turn the ignition back to the 4 (ON) position. The horn will chirp.6. Press the unlock control,
• nearby radio towers,• structures around the vehicle, or• other vehicles parked next to your vehicle.• 3–button remote• 5–button remote• 6–button rem
Commentaires sur ces manuels