Introduction 4Instrument Cluster 10Warning lights and chimes 10Gauges 16Entertainment Systems 19AM/FM stereo 19AM/FM stereo with CD 21AM/FM stereo cas
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
• activate the personal alarm.• arm and disarm the perimeter anti-theft system (if equipped).If there are problems with the remote entry system, make
Opening power liftgate (PLG) (if equipped)Press the control twice within three seconds to power open the powerliftgate. The interior lamps will illumi
If any of the doors, the liftgate or the hood (if equipped with perimeteralarm) are not properly closed, the horn will make two quick chirps andthe pa
Replacing the batteryThe remote entry transmitter uses one coin type three-volt lithiumbattery CR2032 or equivalent.To replace the battery:1. Twist a
transmitters, you can either reprogram them yourself, or take allremote entry transmitters to your authorized dealer forreprogramming.How to reprogram
the remote entry transmitter is used to unlock the door(s), power slidingdoors (if equipped) or liftgate.The illuminated entry system will turn off th
• the ignition is turned to the 4 (ON) position, or• after 25 seconds of illumination.Deactivating/activating perimeter lampsYou may enable/disable th
• open and close the right and left power sliding doors (if equipped).• recall memory seat/side view mirrors/adjustable pedals position Driver1 or Dri
Tips for setting codes:• The factory set code cannot be erased or changed.• The factory code will work even after you have set your own personalcodes.
SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEMSecuriLock娂 passive anti-theft system is an engine immobilizationsystem. This system is designed to help prevent
bulb works. If any light remains on after starting the vehicle, refer to therespective system warning light for additional information.Check engine: T
If your keys are lost or stolen, you will need to do the following:• Use your spare key to start the vehicle, or• Have your vehicle towed to an author
4. Turn the ignition from the 4 (ON) position back to the 3 (OFF)position in order to remove the second coded key from the ignition.5. Within 10 secon
Disarming the systemYou can disarm the system by any of the following actions:• Unlock the vehicle with the remote keyless transmitter.• Unlock the ve
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Push control to lower head restraint.Adjusting the front manual seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback.After returning the sea
To reduce the risk of possible serious injury: Do not hang objectsoff seat back or stow objects in map pocket (if equipped) whena child is in the fron
• Push twice to activate low heat.• Push a third time to deactivate.The indicator light on the control will illuminate when activated. For lowheat, on
The head restraints can be movedup and down by pulling up on thehead restraint.Push button to lower head restraint.Seat mounted cup holders (if equipp
The cupholder is designed to detach from the seat when subjected toheavy load. The cupholder can be reinstalled by returning to the closedposition.Use
Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance mayoccur. It will take you longer
• 2nd row bench seat (if equipped)Note: This seat can be movedforward to keep a child in aLATCH child restraint attachedto the LATCH anchors at thecen
Accessing the third row seat with a second row bucket seatEnsure head restraint is in the fulldown position and seat is adjustedto full rear position
Continuing to lift the handle willtumble the seat forward, allowingeasier access to the third row seat.After entering the 3rd row seat,return the seat
• Ensure that the seat and seatback is latched securely in position.• Keep floor area free of objects that would prevent proper seatengagement.• Do no
After entering the 3rd row, pull backthe seatback until it latches. Thiswill latch and lock the seatback andthe seat track. The seatback andseat will
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped underneath theseatback. After returning the
5. Rotate the seat rearward at a 30to 45 degree angle.6. With the assist handle, pull theseat rearward.7. Remove the seat from vehicle.Second row benc
2. Find the clips attached near theends of the lap/shoulder belts.3. Clip the end of the belt to thestationary portion of the shoulderbelt coming out
4. Position seatback in full downposition.5. From behind seat pull straightback on the release handles locatedon each side of the seat, releasingthe r
2. Install seat onto rear pin of fronttub at a 30 to 45 degree angle.3. Rotate the seat forward until itlatches onto the front pin.4. Rotate seat rear
Engine coolant temperature:Illuminates when the engine coolanttemperature is high. Stop thevehicle as soon as possible, switch off the engine and let
5. Operate recline lever and pushthe seat back upright.Ensure seat is latched to vehicle floor by pushing/pulling on seat.If not latched, the seat may
3. Lower back of seat onto the reartubs until both release controls latchinto place. Be sure that the seat islocked in place both front and back.Do no
2. If you plan to carry very largeobjects or items that might damagethe center lap/shoulder belt, detachthe belt from the seat. Use a key orsafety bel
4. Store the belt in the housingfound on the ceiling by inserting thesmaller tongue in the slot provided.Note: The seat can be stowed withthe safety b
Important: If you don’t let go ofthe number 1 strap before the seatback folds completely, the seat maynot stow flat in the tub. Refer to thelabel atta
8. Pull the number 3 strap on the seat back to tumble seat all the way into the tub in the floor.Do not use the seat anchors as cargo tie downs.Unstow
2. To return the seat back to theseating position, pull the number 1strap, then while holding thenumber 1 strap, pull the number 3strap to raise the s
Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a collision.Ta
3. To return the seat, ensure seatlatching area is free of objects.Then, raise the seat off the liftgatescuff plate and push at the top ofthe seat bac
How does the Personal Safety System姟 work?The Personal Safety System娂 can adapt the deployment strategy of yourvehicle’s safety devices according to c
Speed control: Illuminates whenthe speed control is engaged. Turnsoff when the speed control systemis disengaged.Low washer fluid: Illuminates when th
to the airbag when it begins to inflate. For some occupants, this occursbecause they are initially sitting very close to the airbag. For otheroccupant
Front safety belt energy management retractorsThe front outboard safety belt energy management retractors allowwebbing to be pulled out of the retract
Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.All
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of l
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could re
numbers 611C22–A and 611C22–B respectively). These assemblies canbe obtained from an authorized dealer.Use only extensions manufactured by the same su
Failure to inspect and if necessary replace the safety beltassembly under the above conditions could result in severepersonal injuries in the event of
for the driver and the front passenger. If the BeltMinder威 warnings haveexpired (warnings for approximately 5 minutes) for one occupant (driveror fron
Bulb warning: Illuminates when one of the exterior front turn lamps orrear brake/turn/tail lamps bulb has burned out.• Without Message Center• With Me
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate
• The ignition switch is in the OFF position• The driver and front passenger safety belts are unbuckledWhile the design allows you to deactivate your
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The airbag supplemental restraint system (SRS) is designed to work inconjunction with the safety belts to he
Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.The National Highway Traffic Saf
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
• one or more impact and safing sensors.• Safety belt pretensioner• a readiness light and tone.• diagnostic module.• and the electrical wiring which c
For side airbag equipped vehicles, the front passenger sensing systemwill turn off the passenger seat side airbag if:• the seat is empty and safety be
• Have the person sit upright in the seat, centered on the seat cushion,with the person’s legs comfortably extended.• Restart the vehicle and have the
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. 3 ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase, ful
In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi
A difficulty with the system is indicated by one or more of the following:• The readiness light (same lightfor front and side airbag system)will eithe
How does the side airbag system work?The design and development of the side airbag system includedrecommended testing procedures that were developed b
to inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-frontal collisions, unless the collision causes sufficient lateraldec
Do not attempt to service, repair, or modify the Safety Canopy娂system, its fuses, the A, B, C or D pillar trim, or the headliner ona vehicle containin
• Two crash sensors located at the c-pillar behind the rear doors (oneon each side).• Rollover sensor in the restraints control module (RCM).The Safet
If the Safety Canopy娂 system has deployed, the SafetyCanopy娂 will not function again unless replaced. TheSafety Canopy娂 system (including the A, B, C,
or younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, youmust put them in safety seats made especially for children. Many statesrequi
Booster seats position a child so that safety belts fit better. They lift thechild up so that the lap belt rests low across the hips and the kneesbend
Odometer: Registers the total miles (kilometers) of the vehicle.• Without Message CenterTo switch the display from Metric toEnglish, press and hold th
• Those with a high back.If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo
Move a child to a different seating location if the shoulder beltdoes not stay positioned on the shoulder during use.Follow all instructions provided
When installing a child safety seat:• Review and follow the informationpresented in the AirbagSupplemental Restraint Systemsection in this chapter.• U
Installing child safety seats with combination lap and shoulderbeltsAirbags can kill or injure a child in a child seat. NEVER place arear-facing child
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat.
The tether anchors in your vehicleare in the positions shown:The front passenger seat with power adjustment does not have atether anchor. The two teth
2. Route the child safety seat tetherstrap over the back of the seat. Ifthe head restraint is adjustable,route the tether strap under thehead restrain
If the tether strap is clippedincorrectly (as shown) thechild safety seat may not beretained properly in the event of acollision.5. Rotate the tether
Rear seating positionsFollow Steps 1–7 as described above for the following available seats:• 2nd row bucket• 2nd row bench• 3rd row benchFor addition
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe
Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol.If your vehicle has a second rowb
Follow the child seat manufacturer’s instructions to properly install achild seat with LATCH attachments.Attach LATCH lower attachments of the child s
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙blowout⬙,with unexpected loss of
when you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive.2. Remove the cap from the valve on one t
Tire wearWhen the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Buil
built. For example, the numbers 317 mean the 31st week of 1997. After2000 the numbers go to four digits. For example, 2501 means the 25thweek of 2001.
Important: Remember to replace the wheel valve stems when the roadtires are replaced on your vehicle.It is recommended that the two front tires or two
AUDIO SYSTEMSAM/FM stereo system (if equipped)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various set
Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your
Note: If your tires show uneven wear ask an authorized dealer to checkfor and correct any wheel misalignment, tire imbalance or mechanicalproblem invo
4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new
next two numbers or letters are the plant code designating where it wasmanufactured, the next two are the tire size code and the last fournumbers repr
The tire suppliers may have additional markings, notes or warnings suchas standard load, radial tubeless, etc.Additional information contained on the
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
Changing tires with TPMSEach road tire is equipped witha tire pressure sensor fastenedto the inside rim of the wheel.The pressure sensor is coveredby
When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.
Low Tire PressureWarning LightPossible cause Customer Action RequiredFlashing WarningLightSpare tire in use Your temporary spare tire is inuse. Repair
Seating and Safety Restraints 113Seating 113Safety restraints 138Airbags 153Child restraints 167Tires, Wheels and Loading 182Tire information 182Tire
3. Seek: Press to access thenext/previous strong station ortrack.4. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, pr
SNOW TIRES AND CHAINSSnow tires must be the same size and grade as the tires youcurrently have on your vehicle.The tires on your vehicle have all weat
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle.3. Subtract the combined weight of the driver and pas
1400 – (2 x 220) – (9 x 100) = 1400 – 440 – 900 = 60 lb. Now youhave the load capacity to transport the cement and your friend home.In metric units, t
• Use extra caution when driving while trailer towing. Refer to Drivingwhile you tow in this chapter.• Service your vehicle more frequently if you tow
Preparing to towUse the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. See your authorized dealer or arel
or cause them not to function properly. Your lamp outage featuremay also be disabled or provide incorrect information.See your authorized dealer or tr
AM/FM stereo/ single CD sound system (if equipped)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various
equipped. Refer to the Maintenance and Specifications chapter forthe lubricant specification. Remember that regardless of the rear axlelube used, do n
STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
• Turn the key to 4 (ON) withoutturning the key to 5 (START).Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrume
Important ventilating informationIf the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least one inch (2.
ABS warning lampThe ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringsta
Parking brakeTo set the parking brake, pull thehandle up as far as possible. TheBRAKE warning lamp will illuminateand will remain illuminated until th
• Maneuvering quickly to avoid an accident, pedestrian or obstacle• Hitting a patch of ice• Changing lanes on a snow-rutted road• Entering a snow-free
• A slight deceleration of the vehicle• The AdvanceTrac威 indicator light will illuminate• If your foot is on the brake pedal, you will feel a vibratio
• Heavy or uneven steering efforts may be caused by low power steeringpump fluid level. Check for low power steering pump fluid level beforeseeking se
Treble: Press to adjust the treble setting. Use / / SEEK .Balance: Press to adjust the audio between the left and right speakers.Use/ / SEEK .Fade: Pr
When the key is in the ignition and in the 3 (OFF) position, theautomatic transmission shift lever can be moved from the P (Park)position without the
Understanding the gearshift positions of the 4–speed automatictransaxleP (Park)This position locks the transaxle and prevents the front wheels fromtur
1 (First)• Transaxle operates in first gear only.• Provides maximum engine braking.• Allows upshifts by moving gearshift lever.• Will not downshift in
To help avoid personal injury, always use caution when inR (Reverse) and when using the RSS.This system is not designed to prevent contact with small
The RSS is automatically enabledwhen the gear selector is placed inR (Reverse) and the ignition is ON.The park aid disable switch allowsthe driver to
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
• exact fuel amounts• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsUsing roadside assistanceComple
flash. Press the flasher control again to turn them off. Use it when yourvehicle is disabled and is creating a safety hazard for other motorists.Note:
Note: Always replace a fuse with one that has the specified amperagerating. Using a fuse with a higher amperage rating can cause severe wiredamage and
The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 Relay Accessory delay relay 12 Relay Acces
10. Fast forward: Press tomanually advance in a CD track.11. Rewind: Press to manuallyreverse in a CD track.12. Memory presets: To set astation: Selec
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description12 5A Brake-Shift Interlock (BSI) Runfeed, Climate control system Runfeed13
Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription3 30A** Left cooling fan4 30A** Starter solenoid5 30A** Right-hand power sliding door
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription40 15A* Engine #1 (A/C relay coil, IMRC,HEGO sensors, Canister purge,Transmission mod
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription61 — Not used62 30A* SJB #3 – Right cornering/auxiliarylamps, Right low beam, Left fr
Auxiliary relay box (cooling fans)The relay box is located in the engine compartment by the radiator.Fuse/RelaylocationFuse ampratingDescription1 — Co
The use of tire sealants may damage your tires. The use of tiresealants may also damage your Tire Pressure Monitoring Systemand should not be used.You
• Use commercial car washing equipment• Try to repair the dissimilar spare tireUse of one of the dissimilar spare tires listed above at any one wheell
• Driving vehicles with a load on the cargo rackDrive cautiously when using a full-size dissimilar spare tire/wheel andseek service as soon as possibl
Removing the spare tire1. Wagon only: Open liftgate andlift flap in the carpeting on the reartub cargo floor to expose the hexnut. Insert the lug nut
AM/FM stereo cassette/single CD sound system (if equipped)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select
Tire change procedureWhen one of the front wheels is off the ground, the transaxlealone will not prevent the vehicle from moving or slipping off theja
4. Removing the optional wheelcover or center ornament:• To remove a bolt-on wheel cover(if equipped) loosen the plasticnuts on the center ornament wi
If Ford Accessory Running Boardshave been installed, use the jackadapters supplied with the runningboards as described on the inside ofthe jack storag
11. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lug nuttorque specifications later in thischapter for the proper l
3. Lay the tire flat and secure the cable with wing screw by installing iton the wing screw retainer in the floor and turning the wing screwclockwise.
WHEEL LUG NUT TORQUE SPECIFICATIONSRetighten the lug nuts to the specified torque at 500 miles (800 km)after any wheel disturbance (rotation, flat tir
1. Use only a 12–volt supply to start your vehicle.2. Do not disconnect the battery of the disabled vehicle as this coulddamage the vehicle’s electric
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
Fade: Press to adjust the audio between the front and rear speakers.Use/ / SEEK .Speed sensitive volume (if equipped): Radio volume automaticallychang
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh
authorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of Canada participates in an impartialthird party
GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.
Or call:For a free publication catalog, order toll free: 1-800-782-4356Monday-Friday 8:00 a.m. - 6:00 p.m. ESTHelm, Incorporated can also be reached b
9. Compress (Compression): InCD mode, brings soft and loud CDpassages together for a moreconsistent listening level.10. Repeat: Press to repeat thecur
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
WAXINGApplying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage.• Wash the ve
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub
Do not use chemical solvents or strong detergents when cleaningthe steering wheel or instrument panel to avoid contamination ofthe airbag system.• Be
LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• To clean, use a soft cloth with Motorcraft
Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20)Motorcraft Engine Shampoo (Canada only) (CXC-66-A)Motorcraft One Step Wash and Wax Concentr
SERVICE RECOMMENDATIONSTo help you service your vehicle we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.9L/4.2L V6 engines1. Brake fluid reservoir2. Air filter assembly3. Power distribution box4. Battery5
19. CD eject: Press to eject a CD.20. CD slot: Insert a CD label sideup.21. Seek:Press to access theprevious strong station or track.22. Scan: Press f
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
CHANGING THE WIPER BLADESTo replace the wiper blades:1. Pull the wiper arm away from thewindshield and lock into the serviceposition.2. Turn the blade
5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.•
• Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine isoverfilled, some oil must beremoved from the e
economy requirements of the International Lubricant Standardization andApproval Committee (ILSAC), comprised of U.S. and Japaneseautomobile manufactur
It is recommended that the negative battery cable terminal bedisconnected from the battery if you plan to store your vehicle for anextended period of
relearn its idle and fuel trim strategy for optimum driveability andperformance. To begin this process:1. With the vehicle at a complete stop, set the
concentration should be maintained at 50/50 coolant and distilled water,which equates to a freeze point of -34°F (-36°C). Coolant concentrationtesting
• Be sure to read and understand Precautions when servicing yourvehicle in this chapter.If the engine coolant has not been checked at the recommended
• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcoholand other liquids can cause en
1. / Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various settings.2. Phone/mute: Press to mute theplaying
necessary, add enough 50/50 concentration of engine coolant anddistilled water to bring the liquid level to the proper level.If you have to add more t
• NEVER decrease the coolant concentration below 40%.• Decreased engine coolant concentrations below 40% willdecrease the corrosion protection charact
Automotive fuels can cause serious injury or death if misused ormishandled.Gasoline may contain benzene, which is a cancer-causing agent.Observe the f
When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke whilerefueling. Fuel vapor is extreme
2. Carefully turn the filler cap counterclockwise 1/4 of a turn until itstops.3. Pull to remove the cap from the fuel filler pipe.4. To install the ca
leaded fuel is prohibited by law and could damage your vehicle. Do notuse fuel containing methanol. It can damage critical fuel systemcomponents.Your
performance and emission control system protection for your vehicle.Gasolines that meet the World-wide Fuel Charter should be used whenavailable. Ask
The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fue
Driving style — good driving and fuel economy habitsGive consideration to the lists that follow and you may be able to changea number of variables and
• Carrying unnecessary weight may reduce fuel economy (approximately1 mpg [0.4 km/L] is lost for every 400 lb [180 kg] of weight carried).• Adding cer
4. Aux: Press to toggle betweenFES/DVD and AUX modes. If noauxiliary sources are available, NOAUX AUDIO will be displayed.5. Seek: Press to access the
If other than Ford, Motorcraft or Ford-authorized parts are used formaintenance replacements or for service of components affectingemission control, s
3. The fuel cap may not have been securely tightened. See Fuel fillercap in this chapter.These temporary malfunctions can be corrected by filling the
POWER STEERING FLUIDCheck the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules. If adding fluid isnecess
TRANSMISSION FLUIDChecking automatic transmission fluidRefer to your scheduled maintenance information for scheduledintervals for fluid checks and cha
The transmission fluid should be inthis range if at normal operatingtemperature (150°F-170°F[66°C-77°C]).High fluid levelFluid levels above the safe r
1. Disconnect the Mass Air FlowSensor electrical connector from theair outlet tube.Reposition the locking clip (on theconnector) and squeeze connector
3. Remove the air cleaner assemblyfrom the vehicle.4. Release the two clamps thatsecure the cover to the air filterhousing and place the cover aside.5
8. Replace the air filter housingcover and secure the clamps. Besure all the tabs on the bottom edgeare properly aligned.9. Reinstall the air cleaner
10. Ensure the pads on the bottomof the air cleaner assembly areproperly seated.11. Reconnect the outlet tube to theair cleaner assembly and tighten t
MOTORCRAFT PART NUMBERSComponent 3.9L OHV V6 engine 4.2L OHV V6 engineAir filter element FA-1679 FA-1679Battery BXT-59 BXT-59BXT-65-750 BXT-65-750Fuel
Maintenance and Specifications 267Engine compartment 269Engine oil 271Battery 274Engine coolant 276Fuel information 281Air filter(s) 294Part numbers 2
16. ON/OFF/Volume: Press to turnON/OFF. Turn to increase/decreasevolume.If the volume is set above a certainlevel and the ignition is turned off,the v
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationBrake fluidFill to MAX lineon reservo
Item Capacity Ford part nameFord part number /Ford specificationLock cylinders —Motorcraft Penetratingand Lock LubricantXL-1 /NonePower steering fluid
ENGINE DATAEngine 3.9 L OHV V6 engine 4.2L OHV V6 engineCubic inches 232 256Required fuel 87 octane 87 octaneFiring order 1-4-2-5-3-6 1-4-2-5-3-6Ignit
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
Peace of mindMobile-Ease娂 hands-free communication systemRemote startVehicle security systemsWheel locksFor maximum vehicle performance, keep the foll
AAccessory delay ...68AdvanceTrac ...216Air cleaner filter ...294, 299Air filter, cabin
wheels ...261wiper blades ...263Clock ...66Compas
capacity ...300choosing the right fuel ...284comparisons with EPA fueleconomy estimates ...289de
1. Volume: Press to /increase/decrease volume control.2. Media: Press to select fromdifferent playing medias.3./ : Press to activate dualplay mode and
headlamps ...45headlamps, flash to pass ...46instrument panel, dimming ...47interior lamps ...
Roadside assistance ...225Roof rack ...92SSafety Belt Maintenance ...147Safety belts (see Safe
fluid, refill capacities ...300lubricant specifications ...300Transmissionbrake-shift interlock (BSI) ...219fluid, checking and add
Dual play modePress/ on the rear seat audiocontrols or simultaneously press theradio preset controls 2 and 4 toenable/disable dual play.During dual pl
Cassette/player careDo:• Tighten very loose tapes by inserting a pen or pencil into the hole andturning the hub.• Remove loose labels before inserting
Audio system warranty and serviceRefer to the Warranty Guide for audio system warranty information. Ifservice is necessary, see your dealer or qualifi
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
Dual zone manual heating and air conditioning system with rearpassenger compartment climate control (if equipped)1. Air flow selections: Controlsthe d
will be warmer or cooler than the driver airflow temperature settingwhen more than one rear temperature light (REAR )isilluminated.5.RRear defroster:
In the and modes:• Move the temperature control selector to the coldest setting.• Select A/C and recirculated air. Use with A/C to providecolder airfl
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH REARPASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED)1.Defrost: Distributes outside air through the win
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
engaged manually in any airflow selection except . Recirculated airmay turn off automatically in all airflow selections.7. A/C: Press to activate/deac
Dual zone automatic temperature control with heated seats andrear passenger compartment climate control (if equipped)1.Defrost: Distributes outside ai
7. :Distributes air through the windshield defroster vents and thefloor vents.8.: Distributes air through the floor vents.9.: Distributes air through
19. REAR: Press to enable the control located in the rear seat. Pressagain to turn the auxiliary system off.Operating tips• To reduce fog build up on
AUXILIARY CLIMATE CONTROL (IF EQUIPPED)1. Fan speed: Turn to select thedesired fan speed.2. Temperature/mode selection:The distribution of air from th
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Note:
To program the auto lamp exit time delay:1. Start with the ignition in the OFF position and the headlamp controlin the autolamp position.2. Deselect t
• and the transmission must be out of PARK.Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Light (DR
The dome lamp will not illuminate if the control switch is in the OFFposition.AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimed at
5. Locate the vertical adjuster oneach headlamp, then usea#2Phillips screwdriver to turn theadjuster either counterclockwise (toadjust up) or clockwis
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
Map lamps (if equipped)The map lamps and controls arelocated on the center overheadconsole. Press the raised portion oneach lens to activate the lamps
door is opened. If the control is moved to the driver’s side position, thelamp will not come on at all.The dome lamp will illuminate whenever a front
Function Trade NumberFront park/turn lamps 3457AK (amber)Front sidemarker lamp 904NA (amber)Cornering lamps 3156KAuxiliary parking lamps 912Headlamps
2. Remove the two retainer pins torelease the headlamp assembly andpull headlamp assembly forward toexpose the back of the bulb.3. Disconnect the elec
3. To remove the side marker bulb,turn the bulb socketcounterclockwise, and pull the bulbstraight out of the socket.4. To remove the parking/turnbulb,
Replacing license plate lamp bulbThe license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
From either position, the control will automatically return to the INT2 orOFF position.TILT STEERING WHEELTo adjust the steering wheel:1. Pull and hol
OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehicle’s overhead console will vary according toyour option package.Conversation mirrorThe conve
or metallic objects placed in or on the vehicle may also affect compassaccuracy. Adjustments may need to be made to the zone and calibrationof the com
SPECIAL NOTICESNew Vehicle Limited WarrantyFor a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited
Compass calibration mode1. Press the momentary push buttonand hold it for more than 8 seconds.After 8 seconds, CAL is displayed,then release it.Note:
If the door is allowed to slide open or closed unrestrained,personal injury or damage to the door could result.When closing the sliding door, keep the
Power Sliding Door (PSD) (if equipped)With this option, you can open and close the sliding door(s) with thefollowing controls inside your vehicle.• ov
To power open or close the PSDfrom the second row passengercontrol switch:• Ensure that the PSD is unlocked,using the remote entrytransmitter or power
desirable to prevent power operation of the door by rear seat passengersor if manual operation of the door is desired or necessary when thevehicle is
8. Remove the PSD fuse (fuse #11) from the passenger fuse panel andleave it out for thirty (30) seconds. Refer to the chapter on Fuses andRelays. Refe
CLOCK (IF EQUIPPED)Press the right (+) control to movethe time display forwards.Press the left (-) control to movethe time display backwards.AUXILIARY
• Located next to the second rowseat.• Located on the right trim panel inthe rear cargo area.Cigar/Cigarette lighter (if equipped)Do not plug optional
Press and pull the window switchesto open and close windows.• Push down (to the first detent)and hold the switch to open.• Pull up (to the first deten
The power vent windows areoperated by a single switch locatedon the instrument panel. Press andhold the bottom of the switch toopen or the top of the
• how fast the vehicle was traveling; and• where the driver was positioning the steering wheel.To access this information, special equipment must be d
Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re
POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is
3. Press the SET + control andrelease it.4. Take your foot off the acceleratorpedal.5. The indicatorlight on theinstrument cluster will turn on.Note:•
• Use the accelerator pedal to get to the desired speed. When thevehicle reaches that speed press and release the SET + control.Reducing speed while u
STEERING WHEEL CONTROLS (IF EQUIPPED)Radio control features• Press MEDIA to select AM, FM1,FM2, TAPE or CD (if equipped).In Radio mode:• Press SEEK to
When programming your HomeLink威 Wireless Control System toa garage door or gate, be sure that people and objects are out ofthe way to prevent potentia
3. Simultaneously press and holdboth the HomeLink威 and hand-heldtransmitter button. Do not releasethe buttons until Step 4 hasbeen completed.Some entr
Gate Operator & Canadian ProgrammingDuring programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time for
Erasing HomeLink姞 buttonsTo erase the three programmedbuttons (individual buttons cannotbe erased):• Press and hold the two outerHomeLink威 buttons unt
Info menuThis control displays the followingoptions:• Odometer• Distance to Empty• Trip Odometer• Average Fuel Economy• Trip Elapsed Drive Time• Displ
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
• variations in top-off procedure from one fill-up to another• rounding of the displayed values to the nearest 0.1 gallon (liter)1. Drive the vehicle
Language1. Select this function from theSETUP menu for the currentlanguage to be displayed.2. Pressing the RESET controlcycles the message center thro
Pressing the RESET control cycles the message center through each ofthe systems being monitored and will display the following only whenthere is a mal
Warning display StatusDriver’s door ajar Warning cannot be resetPassenger door ajarLeft rear door ajarRight rear door ajarPark brake set Warning retur
CHECK BRAKE LAMPS. Displayed when the brake lamps areactivated and at least one is burned out. Check the lamps as soon aspossible and have the burned
To reset the oil monitoring system to 100% after each oil change[approximately 5,000 miles (8,000 km) or 180 days] perform thefollowing:1. Press the S
2. Press and release the RESETcontrol to display “OIL LIFE XX%HOLD RESET NEW”.3. Press and hold the RESETcontrol for 2 seconds to display “IFNEW OIL H
POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)Do not install additional floor mats on top of the factory installedfloor mats as they may interfere with th
POWER LIFTGATE (PLG) (IF EQUIPPED)With this option, you can power open or close the liftgate with theprovided controls.• overhead console button• remo
The Power Door Lockout Control islocated in the overhead console.With the control in the OFFposition, power operation is disabledfrom the liftgate han
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
Note: Continued force applied after unlatching may activate the obstacledetection feature and stop the power system. For the best performanceallow the
If any of these conditions occur, the PLG must be reset. To reset thePLG:1. Manually close and fully latch the liftgate.2. Power open the liftgate by
Utility hooksThe utility hooks can be used tohang small items. Do not hang morethan 20 lb. (12 kg) on each of thehooks. The hooks are not designedto r
To remove the cross-bar assembly (if equipped):1. Remove rear support covers fromthe rear rails. Place a small objectinto the pin holes and slide thec
To reinstall the cross-bar assembly (if equipped):1. Slide the cross-bar into the railtrack with the arrow facing towardsthe front of the vehicle. Sli
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
1. Locate the liftgate trim accesspanel in the center of the liftgate.2. Using your key, a smallscrewdriver or knife, pry off theaccess panel.3. Using
RelockThe autolock feature repeats when:• an “autolock” occurrence has already taken place,• the brake is depressed while vehicle speed is less than 5
4. Press the power door unlock control three times.5. Turn the ignition back to the 4 (ON) position. The horn will chirp.6. Press the unlock control,
• nearby radio towers,• structures around the vehicle, or• other vehicles parked next to your vehicle.• 3–button remote• 5–button remote• 6–button rem
Commentaires sur ces manuels