Introduction 4Instrument Cluster 10Warning lights and chimes 10Gauges 14Entertainment Systems 16AM/FM stereo with single CD 16AM/FM stereo with in-das
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a
Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a
• On Sedan’s the anchors arelocated on the rear back panel.• For 3–door/5–door and Wagon,the anchors are located on theback of the rear seat.4. On a s
7. Tighten the child safety seat tether strap according to themanufacturer’s instructions.If the safety seat is not anchored properly, the risk of a c
The LATCH anchors are located onthe rear section of the seat cushion,at the bottom of the seatback.Follow the child seat manufacturer’sinstructions to
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙blowout⬙,with unexpected loss of
Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo
that the vehicle is not ready for I/M testing. See the Readiness forInspection/Maintenance (I/M) testing in the Maintenance andSpecifications chapter.
Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of thetire to set the beads without ad
Highway hazardsNo matter how carefully you drive there’s always the possibility that youmay eventually have a flat tire on the highway. Drive slowly t
• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can be corrected by rotating the tires.Note: If your tir
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
Anti-lock brake system: If theABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected, have the systemserviced immediately by
SNOW TIRES AND CHAINSSnow tires must be the same size and grade as the tires youcurrently have on your vehicle.The original equipment tires on your ve
Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue loadweight is als
GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).
10–15% (conventional trailer), and driver only (150 lb. [68 kg]). Consultyour authorized dealer (or the RV and Trailer Towing Guideprovided by your au
capacity to carry you, 4 of your friends and all the golf bags? You andfour friends average 220 lb. (99 kg) each and the golf bags weighapproximately
TRAILER TOWINGRefer to the following chart to determine how much weight your vehiclecan tow:Model Passengers/Luggageload - lb. (kg)Maximum trailerweig
Preparing to towUse the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. See your authorized dealer or arel
• Consult your local motor vehicle speed regulations for towing a trailer.• To eliminate excessive shifting, use a lower gear. This will also assistin
In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer or flatbed transport vehicle) yourvehicle
STARTINGPositions of the ignition1. LOCK, locks the steering wheel,automatic transaxle gearshift leverand allows key removal.2. OFF, shuts the engine
Upshift (if equipped): Tomaximize fuel economy, this lightilluminates when the manualtransmission should be shifted tothe next highest gear. Refer to
If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf
If starting a vehicle with a manualtransaxle:1. Make sure the parking brake isset.2. Push the clutch pedal to the floor.• Turn the key to 3 (ON) witho
If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important ven
Four-wheel anti-lock brake system (ABS) (if equipped)Your vehicle may be equipped with an Anti-lock Braking System (ABS).This system helps you maintai
The BRAKE warning lamp willilluminate and will remainilluminated until the parking brakeis released.To release, press and hold the button (2), pull th
The Traction Control娂 switch islocated on the center console, bythe gearshift lever. The TractionControl娂 system will automaticallyturn on every time
• loose or worn steering components• improper steering alignmentA high crown in the road or high crosswinds may also make the steeringseem to wander/p
Do not drive your vehicle until you verify that the brakelampsare working.Always set the parking brake fully and make sure the gearshift islatched in
To put your vehicle in gear:• Start the engine• Depress the brake pedal• Move the gearshift lever into the desired gearTo put your vehicle in P (Park)
2 (Second)This position allows for second gear only.• Provides engine braking.• Use to start-up on slippery roads.• To return to D (Overdrive), move t
Headlamps on warning chime: Sounds when the headlamps or parkinglamps are on, the ignition is off (the key is not in the ignition) and thedriver’s doo
To start the vehicle:1. Make sure the parking brake is fully set.2. Press the clutch pedal to the floor, then put the gearshift lever in theneutral po
• The gearshift lever can only be moved into R (Reverse) by moving itfrom left of 3 (Third) and 4 (Fourth) before shifting into R (Reverse).This is a
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
• exact fuel amounts• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsUsing roadside assistanceComple
to turn them off. Use it when your vehicle is disabled and is creating asafety hazard for other motorists.Note: With extended use, the flasher may run
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionR17 — Starter relayR18 — Not usedR19 — Not u
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description33 20A Sunroof34 20A Horn35 7.5A A/C switch, Instrument cluster36 7.5A Inte
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description61 7.5A PATS modules, Instrument cluster62 7.5A Radio (Start)63 20A Power l
To remove a fuse, use the fuse puller tool provided on the powerdistribution box cover.The high-current fuses are coded as follows:Fuse/RelayLocationF
Odometer: Registers the total miles(kilometers) of the vehicle.Trip odometer: Registers the miles(kilometers) of individual journeys.To reset, depress
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription10 1A Battery voltage sense11 30A Subwoofer12 15A Fuel pump motor13 20A Anti-lock Bra
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescriptionR10 — Cooling fan relayR11 — Not usedR12 — Not usedR13 — Not usedR14 — Not usedR15 —
A dissimilar spare tire/wheel is defined as a spare tire and/or wheel thatis different in brand, size or appearance from the road tires and wheelsand
• Use snow chains on the end of the vehicle with the dissimilar sparetire/wheelThe usage of a full-size dissimilar spare tire/wheel can lead toimpairm
To help prevent the vehicle from moving when you change a tire,be sure the parking brake is set, then block (in both directions)the wheel that is diag
5. If equipped with a 6–spoke wheelcover that’s bolted on, remove thefour plastic nuts by turningcounterclockwise 1/4 turn for accessto the lug nuts.N
11. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lug nuttorque specifications later in thischapter for the proper l
Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted.Do not attempt to push-start your automatic transmissionvehicle. A
Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
AUDIO SYSTEMSAM/FM stereo with single CD — Premium (if equipped)AM/FM stereo with single CD/MP3 — Premium (if equipped)2007 Focus (foc)Owners Guide (p
3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
1. / Tune selector: Press tomanually increase/decrease theradio frequency.2. Phone/mute: Press to mute theplaying media. Press again to returnto the p
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
WAXINGApplying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage.• Wash the ve
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal.When washing:• Take care when u
WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub
Do not use chemical solvents or strong detergents when cleaningthe steering wheel or instrument panel to avoid contamination ofthe airbag system.• Be
LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• To clean, use a soft cloth with Motorcraft
Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20)Motorcraft Engine Shampoo (Canada only) (CXC-66-A)Motorcraft One Step Wash and Wax Concentr
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
2. Block the wheels.• Manual transmission:1. Set the parking brake, depress the clutch and place the gearshift inN (Neutral).2. Block the wheels.To re
selector ( / )or SEEK to turn off or select rates 1 through7. Rate 7 compensates the most volume at higher speeds.Setting the clock: Upon initial batt
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.0L/2.3L I4 Engines1. Windshield washer fluid reservoir2. Engine coolant reservoir3. Engine oil fille
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
Poor wiper quality can be improved by cleaning the wiper blades and thewindshield, refer to Windows and wiper blades in the Cleaningchapter.To prolong
Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t
Change your engine oil and filter according to the appropriate schedulelisted in scheduled maintenance information.Ford production and aftermarket (Mo
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a
If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreco
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
Note: Use of Motorcraft Cooling System Stop Leak Pellets or anequivalent product meeting Ford specification WSS-M99B37-B6, maydarken the color of Moto
3. Step back while the pressure releases.4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and re
11. Rewind: Press and hold tomanually reverse the CD.12. Memory presets: To set astation: Select frequency bandAM/FM1/FM2; tune to a desiredstation, p
Severe climatesIf you drive in extremely cold climates (less than –34° F [–36° C ]):• It may be necessary to increase the coolant concentrationabove 5
How fail-safe cooling worksIf the engine begins to overheat:• The engine coolant temperaturegauge will move to the red (hot)area.• The “Check Engine”
FUEL FILTERFor fuel filter replacement, see your authorized dealer. Refer toscheduled maintenance information for the appropriate intervals forchangin
• Automotive fuels can be harmful or fatal if swallowed. Fuel such asgasoline is highly toxic and if swallowed can cause death or permanentinjury. If
RefuelingFuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others:• Read and follow all the instr
If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any
Octane recommendationsYour vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofga
If you have run out of fuel:• You may need to cycle the ignition from OFF to ON several times afterrefueling to allow the fuel system to pump the fuel
• Use the same filling rate setting (low — medium — high) each timethe tank is filled.• Allow no more than two automatic click-offs when filling.• Alw
• Idling for long periods of time (greater than one minute) may wastefuel.• Anticipate stopping; slowing down may eliminate the need to stop.• Sudden
Seating and Safety Restraints 62Seating 62Safety restraints 67Airbags 81Child restraints 92Tires, Wheels and Loading 105Tire information 105Tire infla
AM/FM Stereo with In–dash 6CD —Premium /Audiophile(if equipped)1./ Tune Selector: Press tomanually increase/decrease theradio frequency when in tuner
• Fuel economy may decrease with lower temperatures during the first8–10 miles (12–16 km) of driving.• Driving on flat terrain offers improved fuel ec
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
3. The fuel cap may not have been securely tightened. See Fuel fillercap in this chapter.4. Driving through deep water – the electrical system may be
vehicle is not ready for I/M testing, the following driving cycle consistingof mixed city and highway driving may be performed:15 minutes of steady dr
BRAKE/CLUTCH FLUIDBrake and clutch systems are supplied from the same reservoir.The fluid level will drop slowly asthe brakes wear, and will rise when
6. Install the dipstick making sure it is fully seated in the filler tube.7. Remove the dipstick and inspect the fluid level. The fluid should be inth
If necessary, add fluid in 1/2 pint (250 mL) increments through the fillertube until the level is correct.If an overfill occurs, excess fluidshould be
MOTORCRAFT PART NUMBERSComponent 2.0L I4 engine 2.3L I4 engineAir filter element N/A (Lifetime)1N/A (Lifetime)1Fuel filter FG-1081 FG-1081Oil filter F
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord Part Name orEquivalentFord Part Number /Ford SpecificationBrake fluid and clutchflu
Item CapacityFord Part Name orEquivalentFord Part Number /Ford SpecificationCooling system stopleak pellets—Motorcraft CoolingSystem Stop Leak Pellets
To activate RDS, press and hold MENU until RDS ON or RDS OFFappears in the display. Press MENU again to continue to FIND andSHOW functions. Press the
ENGINE DATAEngine 2.0L I4 engine 2.3L I4 engineCubic inches 121 138Required fuel 87 octane 87 octaneFiring order 1–3–4–2 1–3–4–2Ignition system C.O.P
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
LifestyleAsh cup / smoker’s packageCargo organization and managementTripTunes娂Peace of mindMobile-Ease娂 hands free communication systemRemote startVeh
AAir cleaner filter ...206–207Airbag supplementalrestraint system ...81, 90and child safety seats ...83descrip
Climate control (see Airconditioning or Heating) ...25–26Clutchfluid ...204operation while driving ...
calculating fuel economy ...197cap ...194capacity ...208choosing the right
Lane change indicator(see Turn signal) ...32Liftgate ...50Lights, warning and indicator ...
Occupant ClassificationSensor ...69safety belt maintenance ...75warning light and chime ...76Safet
5. Seek up: Press for next strongstation or CD track. Press and holdfor continuous seek functionality.6. Text: Press in CD mode todisplay track title,
Washer fluid ...181Water, Driving through...141Windowspower...42rear wiper/
221
222
223
224
16. ON/OFF/Volume: Press to turnON/OFF; turn to increase/decreasethe volume levels. If the volume isset above a certain level and theignition is turne
• Station overload: When you pass a broadcast tower, a stronger signalmay overtake a weaker one and play while the weak station frequencyis displayed.
HEATER ONLY SYSTEM(IF EQUIPPED)1. Air flow selections: Controlsthe direction of the airflow in thecabin. See the following for a briefdescription on e
2. Adjust the temperature control to maintain comfort.3. Set the fan speed to the highest setting.4. Direct the outer instrument panel vents toward th
5. A/C: Provides cabin cooling.6. Temperature selection: Controls the temperature of the airflow inthe cabin.Max A/C: For maximum cabin cooling perfor
REAR WINDOW DEFROSTERThe rear defroster control is located on the instrument panel.Press the rear defroster control to clear the rear window of thin i
HEADLAMP CONTROLTurns the lamps off.Turns on the parkinglamps, instrument panel lamps,license plate lamps and tail lamps.Turns the headlamps on.Ambien
Maintenance and Specifications 178Engine compartment 180Engine oil 182Battery 184Engine coolant 186Fuel information 192Air filter(s) 206Part numbers 2
High beamsPull the lever towards you toactivate. Pull the lever towards youagain to deactivate.Flash to passPull toward you slightly to activateand re
Vertical aim adjustment1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away.• (1) 8 fe
TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSDome lampsThe dome lamp is equ
Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America to
Replacing headlamp bulbs1. Make sure the headlamp controlis in the OFF position and open thehood.2. Pull off the bulb cap.3. Disconnect electrical con
Replacing tail/brake/backup lights and turn signal bulbs (3dr & 5dr)1. Make sure the headlamp controlis in the OFF position and thenopen the hatch
Replacing tail/brake/backup lights and turn signal bulbs (wagon)1. Make sure the headlamp controlis in the OFF position and thenopen the hatchback.2.
Replacing high-mount brake lamp bulbsSedan1. Make sure the headlamp controlis in the OFF position and open theluggage compartment.2. Pull the bulb hol
Replacing the luggage compartment lamp1. Make sure the headlamp controlis in the OFF position.2. Carefully pry out the lightassembly from the holder w
MULTI-FUNCTION LEVERWindshield wiper: Move the leverdown for a single wipe.For intermittent operation, movecontrol up one position and adjustthe rotar
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
TILT AND TELESCOPE STEERING COLUMN (IF EQUIPPED)Pull the locking lever down to adjustand telescope the steering columnposition. Return the lever to it
• Place the VELCRO威 hook ontothe side of the aftermarkettransmitter opposite of thebutton.• Place the transmitter into storagecompartment, button down
Cigar lighter (if equipped)Do not plug optional electrical accessories into the cigarette lightersocket.Do not hold the lighter in with your hand whil
EXTERIOR MIRRORSPower side view mirrors (if equipped)To adjust your mirrors:1. Rotate the control clockwise toadjust the right mirror and rotatethe co
Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas
Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RES contro
• Depress the brake pedal until thedesired vehicle speed is reached,press the SET ACCEL control.Turning off speed controlPress the speed control OFFco
Move the SEEK control towards the instrument panel to seek to thenext radio station down the frequency band or the previous CD track.• MODE: Press and
To vent:• To tilt the moon roof into the vent position (when the glass panel isclosed), press and hold the front portion of the control.• To close the
POSITIVE RETENTION FLOOR MATDo not install additional floor mats on top of the factory installedfloor mats as they may interfere with the accelerator
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
To reduce the risk of injury, the luggage cover must be properlyattached to the mounting clips.Do not place any objects on the cargo area cover. They
LUGGAGE RACK (IF EQUIPPED)The maximum recommended load is220 lbs (100 kg) on the luggagerack structure. The load must beplaced directly on the dealeri
KEYSThe key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency.You
1. Turn the ignition to the 3 (ON)position.2. Press the power door unlockcontrol three times.3. Turn the ignition from 3 (ON)position to the 2 (OFF) p
INTERIOR LUGGAGE COMPARTMENT RELEASEYour vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of esc
REMOTE ENTRY SYSTEM (IF EQUIPPED)This device complies with part 15 of the FCC rules and with RSS-210 ofIndustry Canada. Operation is subject to the fo
2. With the all-door remote entry, press and release again withinthree seconds to unlock all the doors.The remote entry system activates the illuminat
Note: The panic alarm will only operate when the ignition is in the 1(LOCK) or 2 (OFF) position.Opening the luggage compartmentPress once to open the
5. Snap the two halves back together.Note: Replacement of the battery will not cause the remote transmitterto become deprogrammed from your vehicle. T
started unless a coded key programmed to your vehicle is used. Theuse of the wrong type of coded key may lead to a “no-start” condition.Your vehicle c
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental restraint
Programming spare keysYou can program your own coded keys to your vehicle. Please read andunderstand the entire procedure before you begin.Tips:• A ma
11. Your new, unprogrammed key is now programmed.If the key has been successfully programmed it will start the vehicle’sengine and the theft indicator
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Adjusting the front manual seatSitting improperly out of position or with the seat back reclinedtoo far can take off weight from the seat cushion and
Lift the control to adjust the angleof the seatback.Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in se
Tip/slide front seat (3–door)Lift the control and fold theseatback forward.The seat can be slid forward toallow easier entry to the rear seats.Slide t
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback.After returning the sea
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback.After returning the sea
Your vehicle’s Personal Safety System娂 consists of:• Driver and passenger dual-stage airbag supplemental restraints.• Front safety belts with pretensi
information early in the crash event on the severity of the impact. Thisallows your Personal Safety System娂 to distinguish between differentlevels of
Cell phone useThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri
will light and stay lit to remind you that the front passenger frontalairbag is off. See Front passenger sensing system in the airbags sectionof this
• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and warning light are repaired.If any of these thin
Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.Combination lap and shoulder bel
response to vehicle movement. For example, if the driver brakessuddenly or turns a corner sharply, or the vehicle receives an impact ofapproximately 5
How to disengage the automatic locking modeFord Motor Company recommends that all passenger safety beltassemblies and attaching hardware should be ins
Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could re
a collision be replaced. However, if the collision was minor and anauthorized dealer finds that the belts do not show damage and continueto operate pr
therefore potentially in need of a warning. To avoid activating theBeltMinder威 feature for objects placed in the front passenger seat,warnings will on
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
• The ignition switch is in the OFF position• The driver and front passenger safety belts are unbuckledWhile the design allows you to deactivate your
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The supplemental restraint system is designed to work with the safetybelt to help protect the driver and rig
All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bagsupplemental restraint system (
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
• Front passenger sensing system. Refer to Front passenger sensingsystem. later in this chapter.• “Passenger airbag off” or “pass airbag off” indicato
For side airbag equipped vehicles, the front passenger sensing systemwill turn off the passenger seat side airbag if:• the seat is empty and safety be
• Have the person sit upright in the seat, centered on the seat cushion,with the person’s legs comfortably extended.• Restart the vehicle and have the
ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. 3 ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase, ful
In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
A difficulty with the system is indicated by one or more of the following:• The readiness light (same lightfor front and side airbag system)will eithe
How does the side airbag system work?The side airbag system consists ofthe following:• An inflatable nylon bag (airbag)with a gas generator concealedb
Several air bag system components get hot after inflation. Do nottouch them after inflation.If the side airbag hasdeployed, the airbag willnot functio
Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather, they could burn a small child. Checkseat covers and buckle
Child booster seatsChildren outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the la
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto
Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in acollision.SAFETY SEATS F
tether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. Formore info
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
Commentaires sur ces manuels