Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 18Entertainment Systems 21How to get going 21AM/FM stereo with CD 25AM/FM stereo
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
• Press the speed control OFFcontrol.Note: When you turn off the speedcontrol or the ignition, your speedcontrol set speed memory is erased.STEERING W
In any mode:• Press VOL + or − to adjustvolume.Climate control features (if equipped)Press TEMP + or - to adjusttemperature.Press FAN + or - to adjust
Navigation control features(if equipped)Press and hold VOICE briefly untilthe voiceicon appears on theNavigation display to use theNavigation voice co
Bounce back override: To override bounce back, within 2 seconds afterreaching bounce back position, if the switch is held in the close positionthe moo
purchase). It is also suggested that upon the sale of the vehicle, theprogrammed Homelink威 buttons be erased for security purposes, refer toProgrammin
door does not activate, press and hold the just-trained HomeLink威button and observe the indicator light.• If the indicator light stays on constantly,
seconds (“cycle”) your hand-held transmitter until the frequencysignal has been accepted by the HomeLink威. The indicator light willflash slowly and th
For questions or comments, contact HomeLink威 at www.homelink.comor 1–800–355–3515.STANDARD MESSAGE CENTER (IF EQUIPPED)With the ignition in the ON pos
The DTE function will display LOW FUEL LEVEL and sound a tone forone second when you have approximately 50 miles (80 km) to empty. Ifyou RESET this wa
• Autolamp• Autolock• Autounlock• Park Aid (if equipped)• Oil Life Start ValueBriefly press the SELECT/RESET control switch to scroll through theSETUP
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
To reset the oil monitoring system to 100% after each oil change[approximately 5,000 miles (8,000 km) or 180 days] perform thefollowing:1. Enter SYSTE
1. Select this function from theSETUP MENU for the currentlanguage to be displayed.2. Press and hold theSELECT/RESET control to select anew language.S
AutounlockThis feature automatically unlocks all vehicle doors when the driver’sdoor is opened within 10 minutes of the ignition being turned off.1. T
Compass display (if equipped)The compass heading is displayed as one of N, NE, E, SE, S, SW, W andNW in the message center display.The compass reading
4. Press and hold the reset buttonon the compass module forapproximately 4 seconds untilCOMPASS ZONE XX appears in themessage center display.5. Contin
System warningsSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems.In the event of a multiple warning si
Warning display StatusLiftgate/glass ajar Warning returns after the conditionhas cleared then reoccurs within thesame ignition ON-OFF cycle.Clear obje
TIRE SENSOR FAULT. Displayed when a tire pressure sensor ismalfunctioning, or your spare tire is in use. For more information on howthe system operate
OPTIONAL MESSAGE CENTER (IF EQUIPPED)With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant veh
Info menuThe Info menu items are shown onthe top two lines of the messagecenter. Press the INFO control todisplay the following:• Trip odometer (Trip
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in miles/gallon or liters/km.If you calculate you
Fuel UsedSelecting this function from theINFO menu. “FUEL USED XXX.XGAL” will display the fuel used sincelast reset. The information displayedwill be
• Compass Zone (if equipped)• Compass Calibration (if equipped)• Oil Life Start ValueSystem checkSelecting this function from theSETUP MENU causes the
1. Enter SYSTEM CHECK to display“OIL XXX% OIL LIFE OK”.2. Press RESET control to display“HOLD RESET IF NEW OIL”.3. Press and hold the RESETcontrol for
1. Select this function from theSETUP MENU for the currentlanguage to be displayed.2. Press the RESET control to cyclethe message center through each
AutounlockThis feature automatically unlocks all vehicle doors when the driver’sdoor is opened within 10 minutes of the ignition being turned off.1. T
1. To disable/enable the easy exitseat feature, select this functionfrom the SETUP MENU.2. Press the RESET control to turnthe easy entry exit seat ON
Note: Compass zone and calibration adjustments can be entered byusing the INFO and SETUP MENU controls or using the reset button ontop of the compass
Compass calibration adjustmentPerform compass calibration in an open area free from steel structuresand high voltage lines. For optimum calibration, t
System warningsSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems.In the event of a multiple warning si
Note: Some warning lights will display in the message center as wordsand function the same as the warning light.Note: Depending on which options your
Warning display StatusLiftgate/glass ajar Warning returns after the conditionhas cleared then reoccurs within thesame ignition ON-OFF cycle.Clear obje
TIRE SENSOR FAULT. Displayed when a tire pressure sensor ismalfunctioning, or your spare tire is in use. For more information on howthe system operate
RUNNING BOARDS (IF EQUIPPED)Deployable running boards (DRB) automatically move when the doorsare opened to assist entering and exiting the vehicle.Aut
Note: Do not use the running boards, front and rear hinge assemblies,running board motors, or the running board under body mounts to liftthe vehicle w
CARGO COVER (IF EQUIPPED)Your vehicle may be equipped with a cargo area cover that covers theluggage compartment of your vehicle.To install the cover:
5 passenger stowage:When the lid is open, it will standup on its own.1. To open, lift the release handleand the lid.2. To close, lower the lid, lift t
LUGGAGE RACKYour vehicle is equipped with a roofrack. The maximum recommendedload is 100 lbs (45 kg), evenlydistributed. Use the tie down loopson the
KEYSOne key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency.Your keys are programmed to your v
Deactivating/activating autolockYour vehicle comes with the autolock feature enabled. There are fourmethods to enable/disable this feature:• Through y
4. Press and hold the 3 • 4. While holding the 3 • 4pressthe7• 8.5. Release the 7 • 8.6. Release the 3 • 4.The user should receive a horn chirp to ind
• Optional instrument clusterBrake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when the
Power door unlock/lock procedureYou must complete Steps 1-5 within30 seconds or the procedure willhave to be repeated. If theprocedure needs to be rep
Power door lock/unlock inhibit feature (if equipped)If the key is not in the ignition, all doors are closed, and the vehicle hasbeen locked using the
CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the
The remote entry system allows youto lock or unlock all vehicle doorsand liftgate, open the liftgatewindow without a key and activatethe panic alarm.T
transmitter for approximately 4 seconds. The parklamps will flash twiceto indicate that the vehicle has switched to one step unlocking. Repeatthe proc
2. Press the SET control on thelower-center portion of theinstrument panel.3. Within 5 five seconds, press onecontrol on the remote transmitterand the
2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery. Note: Please refer to local r
Note: Ensure the brake pedal is notdepressed during this sequence.To reprogram the remote entrytransmitters:1. Ensure the vehicle is electronically un
The inside lights will not turn off if:• they have been turned on with the dimmer control, or• any door is open.The battery saver will shut off the in
Tips:• Do not set a code that uses five of the same number.• Do not use five numbers in sequential order.• The factory set code will work even if you
Safety belt: Reminds you to fastenyour safety belt. A Belt-Minder威chime will also sound to remind youto fasten your safety belt. Refer tothe Seating a
SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEMSecuriLock娂 passive anti-theft system is an engine immobilizationsystem. This system is designed to help prevent
Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 2(ACCESSORY) position.The theft indicator will flash everytwo seco
Please read and understand theentire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition.2. Turn the igniti
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Push control to lower head restraint.Adjusting the front manual seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving
Using the manual lumbar support (if equipped)For more lumbar support, turn thelumbar support control toward thefront of vehicle.For less lumbar suppor
To reduce the risk of possible serious injury: Do not hang objectsoff seat back or stow objects in the seatback map pocket (ifequipped) when a child i
Press the control to recline theseatback forward or rearward.Using the power lumbar support (if equipped)The power lumbar control is located on the ou
• only in Park or Neutral if the ignition is in the RUN position.A memory seat position may be programmed at any time.The memory positions are also re
1. Lower the head restraints bypulling on the strap.2. Locate handle on the side of theseat cushion by the door.3. Pull up on the handle and pushthe s
Never remove the coolant reservoir cap while the engine isrunning or hot.Low tire pressure warning:Illuminates when your tire pressureis low. If the l
3. Lift up on the head restraint untilit locks into its original position.Before returning the seatback to its original position, make surethat cargo
Returning to the upright position from full lowered load floorpositionThe seatback cannot be returned to the upright position until the seat isreturne
To return the seat to a seating position:1. Push the seat down and latch tothe floor with a moderate amount ofeffort and speed.2. Make sure the seat i
Exiting the 3rd row1. Pull on the lever/strap (asequipped) located at the bottomright of the seat back to release theseat from the floor, and rotate t
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback.After returning the sea
Push the top of the control buttonto return the seatback to its originalposition.The power fold down seats will operate for 30 minutes after theigniti
• Front passenger sensing system• “Passenger airbag off” or “pass airbag off” indicator lamp• Front crash severity sensor.• Restraints Control Module
Driver’s seat position sensorThe driver’s seat position sensor allows your Personal Safety System娂 totailor the deployment level of the driver dual-st
safety belt pretensioner activation depending upon safety belt usage.Refer to Safety restraints section in this chapter.Front safety belt pretensioner
Safety restraints precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injur
AdvanceTrac威: Flashes when theAdvanceTrac威 with RSC system isactive. Illuminates solid when thesystem has been disabled (by thedriver or as a result o
Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Checkseat covers and buckle
• Front and rear seatsAll safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder be
How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt
After any vehicle collision, the combination lap and shoulder beltsystem at all passenger seating positions must be checked by anauthorized dealer to
Front safety belt height adjustmentYour vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shou
To adjust the comfort guide:1. Slip the shoulder belt into thebelt guide.2. Slide the guide up or down alongthe webbing so that the belt iscentered on
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war
The Belt-Minder威 feature uses two different warning chimes. During thefirst minute of activation, the warning chime will sound once everysecond. The r
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra
Do not sit on top of a buckled safety belt or insert a latchplateinto the buckle to avoid the Belt-Minder威 chime. To do so mayadversely affect the per
Turn signal: Illuminates when theleft or right turn signal or thehazard lights are turned on. If theindicators stay on or flash faster, check for a bu
1. Turn the ignition switch to the RUN (or ON) position. (DO NOTSTART THE ENGINE)2. Wait until the safety belt warning light turns off. (Approximately
Failure to inspect and if necessary replace the safety beltassembly under the above conditions could result in severepersonal injuries in the event of
Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.The National Highway Traffic Saf
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
• one or more impact and safing sensors.• a readiness light and tone.• diagnostic module.• and the electrical wiring which connects the components.• F
For side airbag equipped vehicles, the front passenger sensing systemwill turn off the passenger seat side airbag if:• the seat is empty and safety be
• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LampPasseng
ObjectsPass Airbag OffIndicator LampPassengerAirbagSmall (i.e. 3 ring binder, smallpurse, bottled water)Unlit DisabledMedium (i.e. heavy briefcase,ful
In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi
Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,
A difficulty with the system is indicated by one or more of the following:• The readiness light will eitherflash or stay lit.• The readiness light wil
automotive safety experts known as the Side Airbag Technical WorkingGroup. These recommended testing procedures help reduce the risk ofinjuries relate
Several air bag system components get hot after inflation. Do nottouch them after inflation.If the side airbag hasdeployed, the airbag willnot functio
To reduce risk of injury, do not obstruct or place objects in thedeployment path of the inflatable Safety Canopy娂.How does the Safety Canopy姟 system w
booster seat because it is designed to inflate downward from theheadliner above the doors along the side window openings.The Safety Canopy娂 system is
Any difficulty with the system is indicated by one or more of thefollowing:• The readiness light (same light as for front airbag system) will eitherfl
Children and safety beltsIf the child is the proper size, restrain the child in a safety seat. Childrenwho are too large for child safety seats (as sp
lap/shoulder belt to fit properly. Generally this is when they weigh about80 lb. (36 kg) (about 8 to 12 years old).Booster seats should be used until
• Those with a high back.If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo
Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto
Seating and Safety Restraints 153Seating 153Safety restraints 165Airbags 181Child restraints 195Tires, Wheels and Loading 210Tire information 212Tire
Trip odometer: Registers the miles (kilometers) of individual journeys.• Standard instrument clusterPress the SELECT/RESET controlonce to switch from
Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in acollision.SAFETY SEATS F
tether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. Formore info
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a
Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a
1. Position the child safety seat on the rear seat cushion.2. Route the tether strap under the head restraint and between the headrestraint posts.3. L
4. Clip the tether strap to theanchor.If the tether strap is clipped incorrectly, the child safety seatmay not be retained properly in the event of a
Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol:• 5 passenger vehicle• 6 passenge
The lower anchors for child seatinstallation are located at the rearsection of the second row seatbetween the cushion and seat back.The LATCH anchors
If you install a child seat with rigid LATCH attachments, do not tightenthe tether strap enough to lift the child seat off the vehicle seat cushionwhe
AUDIO SYSTEMSQuick start — How to get goingListening to the radio1. If the audio system is off, pressVOL-PUSH to turn the radio on.Turn VOL-PUSH to ad
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary
• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and
government test course. For example, a tire graded 150 would wear oneand one-half (1 1/2) times as well on the government course as a tiregraded 100.
• Tire Identification Number (TIN): A number on the sidewall ofeach tire providing information about the tire brand andmanufacturing plant, tire size
At least once a month and before long trips, inspect each tire and checkthe tire pressure with a tire gauge (including spare, if equipped). Inflateall
To check the pressure in your tire(s):1. Make sure the tires are cool, meaning they are not hot from drivingeven a mile.If you are checking tire press
cracking, cuts, bruises and other signs of damage or excessive wear. Ifinternal damage to the tire is suspected, have the tire demounted andinspected
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of thetire to set the beads without ad
Listening to satellite radio (if equipped)1. If the audio system is turned off,press VOL-PUSH to turn the radioon. Turn VOL-PUSH to adjust thevolume.N
If your vehicle is stuck in snow, mud, sand, etc., do not rapidlyspin the tires; spinning the tires can tear the tire and cause anexplosion. A tire ca
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
Changing tires with TPMSEach road tire is equipped witha tire pressure sensor fastenedto the inside rim of the wheel.The pressure sensor is coveredby
no longer capable of functioning as intended. Please refer to thefollowing chart for information concerning your Tire Pressure MonitoringSystem:Low Ti
For a single CD system, if a discis not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the
Low Tire PressureWarning LightPossible cause Customer Action RequiredFlashing WarningLightSpare tire in use Your temporary spare tire is inuse. Repair
any tire is under-inflated, carefully drive the vehicle to the nearestlocation where air can be added to the tires. Inflate all the tires to therecomm
Vehicle Curb Weight – is the weight of your new vehicle when youpicked it up from your authorized dealer plus any aftermarketequipment.Payload – is th
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury.Steps for determining the correct l
to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400
TRAILER TOWINGTrailer towing with your vehicle may require the use of a trailer towoption package.Trailer towing puts additional loads on your vehicle
4x2GCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.0L SOHC Class
Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random pl
4X4GCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.0L SOHC Class
Safety chainsAlways connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cr
Driving while you towWhen towing a trailer:• Keep your speed no faster than 70 mph (112 km/h) during the first500 miles (800 km) of towing a trailer,
refilling your rear axle with synthetic gear lube if not already soequipped. Refer to the Maintenance and Specifications chapter forthe lubricant spec
Rear Wheel Drive (RWD) 4x2 vehicles:This applies to all 4x2 trucks/sport utilities with rear wheel drivecapability.• Place the transmission in N (Neut
STARTINGPositions of the ignition1. OFF/LOCK, shuts off the engineand all accessories/locks the steeringwheel, gearshift lever and allows keyremoval.2
If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf
• Make sure the gearshift is in P(Park).3. Turn the key to 3 (ON) withoutturning the key to 4 (START).Some warning lights will briefly illuminate. See
Starting the engine1. Turn the key to 3 (ON) withoutturning the key to 4 (START). Ifthere is difficulty in turning the key,rotate the steering wheel u
To reduce the risk of electrical shock, do not use your heaterwith ungrounded electrical systems or two-pronged (cheater)adapters.BRAKESOccasional bra
AM/FM Single CD/MP3 satellite compatible sound system(if equipped)Accessory delay: Your vehicle is equipped with accessory delay. Withthis feature, th
Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake
Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.ADVANCETR
If your vehicle should become stuck in deep snow or mud, try switchingthe AdvanceTrac威 with RSC system off by pressing the AdvanceTrac威with RSC button
• Driving on slick surfaces.• Cornering while towing a heavily loaded trailer (refer to Trailertowing in the Tires, Wheels and Loading chapter.)Roll S
If the vehicle is above 25 mph (40 km/h), momentarily pressing theAdvanceTrac威 with RSC button will steadily illuminate the “sliding car”icon, however
Aggressive driving in any road conditions can cause you to losecontrol of your vehicle increasing the risk of severe personalinjury or property damage
PREPARING TO DRIVEUtility vehicles have a significantly higher rollover rate thanother types of vehicles.In a rollover crash, an unbelted person is si
2. Remove the rubber pad at thebottom of the cup holder to locatethe access cap of the floor shifterassembly.3. Using a screwdriver (orequivalent), re
Driving with a 5–speed automatic transmission (if equipped)This vehicle is equipped with an Adaptive Transmission Control Strategy.This Adaptive Trans
P (Park)This position locks the transmissionand prevents the rear wheels fromturning.To put your vehicle in gear:• Start the engine• Depress the brake
3. MENU: Press repeatedly toaccess the following settings:CATEGORY (satellite radio if equipped): Press MENU until thecurrently active category appear
D (Drive) without OverdriveOverdrive can be deactivated bypressing the transmission controlswitch on the side of the gearshiftlever.• This position al
Forced downshifts• Allowed in D (Overdrive) or Drive.• Depress the accelerator to the floor.• Allows transmission to select an appropriate gear.Drivin
P (Park)This position locks the transmissionand prevents the rear wheels fromturning.To put your vehicle in gear:• Depress the brake pedal• Start the
D (Drive) without OverdriveOverdrive can be deactivated bypressing the transmission controlswitch on the side of the shift lever.• This position allow
• Allows upshifts by moving gearshift lever.• Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds
Certain add-on devices such as large trailer hitches, bike orsurfboard racks and any device that may block the normaldetection zone of the reverse sen
Audible WarningsDistance to Object Warning13 feet (4 meters) to 19.6 feet (6 meters) Slow beepSpeed below 2.5 mph (4 km/h)up to 1.4 feet (.4 meters) S
System indicator lights• 4X4 - momentarily illuminateswhen the vehicle is started.Illuminates when 4X4 HIGH(4WD High) is selected.• 4X4 LOW – momentar
3. Place the transmission in N (Neutral).4. Press the desired 4WD position.• If shifting into 4X4 LOW (4WD Low), wait for the 4X4 LOW light inthe inst
pavement only after reducing your speed. Do not turn the steeringwheel too sharply while returning to the road surface.• It may be safer to stay on th
The default setting is off; increasing your vehicle speed will not changethe volume level.Adjust 1–7: Increasing this setting from 1 (lowest setting)
not more. Additionally, smooth variations of the accelerator and/orbrake pedal pressure should be utilized if changes in vehicle speed arecalled for.
4WD Systems4WD uses all four wheels to power the vehicle. This increases traction,enabling you to drive over terrain and road conditions that aconvent
Once through water, always try the brakes. Wet brakes do not stop thevehicle as effectively as dry brakes. Drying can be improved by movingyour vehicl
When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This r
faster, because as in other vehicles, braking occurs at all four wheels. Donot become overconfident as to road conditions.Make sure you allow sufficie
DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsUsing roadside assistanceComplete the roadside assi
HAZARD FLASHERThe hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is
The fuel pump shut-off switch islocated in the passenger’s foot well,by the kick panel.Use the following procedure to reset the fuel pump shut-off swi
5. SEEK: In radio mode,press/ to access theprevious/next strong station.In CD mode, press/ toaccess the previous/next CD track.In satellite radio mode
Note: Always replace a fuse with one that has the specified amperagerating. Using a fuse with a higher amperage rating can cause severe wiredamage and
Passenger compartment fuse panelThe fuse panel is located below theinstrument panel on the driver’sside.To remove a fuse use the fuse puller tool prov
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description6 20A Liftglass release motor, Doorunlock/lock7 15A Trailer stop/turn8 15A
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description24 10A Cluster, Theft LED25 15A Trailer tow park lamps26 15A License plate/
Always disconnect the battery before servicing high currentfuses.To reduce risk of electrical shock, always replace the cover tothe Power Distribution
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription7 40A** Powertrain Control Module(PCM)8 40A** Heated windshield (left)9 40A** Heated
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription35 10A* AC clutch36 — Not used37 30A* Front wiper38 15A* 5R Transmission39 15A* PCM p
CHANGING THE TIRESIf you get a flat tire while driving:• do not brake heavily.• gradually decrease the vehicle’s speed.• hold the steering wheel firml
A dissimilar spare tire/wheel is defined as a spare tire and/or wheel thatis different in brand, size or appearance from the road tires and wheelsand
• Use snow chains on the end of the vehicle with the dissimilar sparetire/wheelThe usage of a full-size dissimilar spare tire/wheel can lead toimpairm
8. FOLDER : In folder mode,press FOLDERto access nextfolder on MP3 discs, if available.9.FOLDER: In folder mode,press FOLDER to access theprevious fol
4. Turn off the power running boards (if equipped). Refer to Runningboards in the Driver Controls chapter.Note: Passengers should not remainin the veh
Removing the jack and tools1. Open liftgate and remove thecarpeted floor lid.2. Turn jack screw eyelet (1)counterclockwise to releasepressure.3. Rotat
2. Insert the lug wrench on thewinch drive nut.The wrench will stop moving andforward resistance to turning will befelt when properly engaged.3. Turn
Do not attempt to change a tire on the side of the vehicle closeto moving traffic. Pull far enough off the road to avoid thedanger of being hit when o
4. Position the jack according to theillustrated guides and turn the jackhandle clockwise until the tire is amaximum of 1 inch (25 mm) off theground.N
8. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torquespecifications later in this chapterfor the proper lu
Re-stowing the jack and tools1. Unblock the wheels.2. Stow the wheel ornament (if removed) in a safe location in the vehicle(such as the glove box or
JUMP STARTINGThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury orvehicle da
Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to the g
Maintenance and Specifications 320Engine compartment 322Engine oil 325Battery 330Engine coolant 332Fuel information 338Air filter(s) 352Part numbers 3
In satellite radio mode (if equipped), press and hold to hear a briefsampling of the next channels. Press again to stop. In CATEGORYMODE, press SCAN t
Do not connect the end of the second cable to the negative (-)terminal of the battery to be jumped. A spark may cause anexplosion of the gases that su
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGNote: Turn off the power running boards (if equipped) prior topreparing the vehicle for towing. Refer to Running boards in the DriverCon
On 4x4/AWD vehicles, it is recommended that your vehicle be towedwith a wheel lift and dollies or flatbed equipment with all the wheels offthe ground.
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio
Audiophile AM/FM in-dash six CD/MP3 satellite compatible soundsystem (if equipped)Accessory delay: Your vehicle is equipped with accessory delay. With
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is
• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent qu
• To remove tar and grease, use Motorcraft Bug and Tar Remover(ZC-42), available from your authorized dealer.ENGINEEngines are more efficient when the
4.6L V8 Engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTIC (NON-PAINTED) EXTERIO
• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32-A),available from your au
If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows:1. Wipe up spilled liqui
LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• To clean, use a soft cloth with Motorcraft
Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20)Motorcraft Engine Shampoo (Canada only) (CXC-66-A)Motorcraft One Step Wash and Wax Concentr
2. MUTE/ : Press to mute theplaying media. Press again to returnto the playing media.3. MENU: Press repeatedly toaccess the following settings:CATEGOR
SERVICE RECOMMENDATIONS• Use the scheduled maintenance information to track routineservice.• Use only recommended fuels, lubricants, fluids and servic
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.0L SOHC V6 engine1. Engine oil filler cap2. Engine oil dipstick (out of view)3. Brake fluid reservoi
4.6L V8 engine1. Air filter assembly2. Engine oil filler cap3. Engine oil dipstick4. Brake fluid reservoir5. Power distribution box6. Battery7. Power
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas
• 4.0L V6 engine• 4.6L V8 engine6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.• If the oil level is between the lower a
• 4.0L V6 engine• 4.6L V8 engine• Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized de
To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level indicator and/or the engine oil filler cap removed.Engine Oil Recommen
4.6L 3V V8 EngineLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by the AmericanPetroleum
To search for specific RBDS music categories: When the desiredcategory appears in the display, press/ to find the desired type,then press and release
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If
Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyeswhen working near
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
• 4.0L V6 engine• 4.6L V8 engine• The engine coolant should be at the “FULL COLD” level as listed onthe engine coolant reservoir (depending upon appli
Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservo
For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when
Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium
• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i
Oil overheat can be triggered in severe driving conditions, such astowing heavy loads over mountainous terrain in extreme hottemperatures. As oil temp
The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stopsbefore completely rem
COMPRESS (Compression): Available only in CD/MP3 mode. PressMENU until COMPRESS ON/OFF appears in the display. Use/ /SEEK, SEEK to toggle ON/OFF. When
• Be particularly careful if you are taking “Antabuse” or other forms ofdisulfiram for the treatment of alcoholism. Breathing gasoline vapors,or skin
Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1/4 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref
If you do not use the proper fuel filler cap, excessive vacuum inthe fuel tank may damage the fuel system or cause the fuel capto disengage in a colli
Fuel qualityIf you are experiencing starting, rough idle or hesitation driveabilityproblems, try a different brand of unleaded gasoline. “Premium”unle
ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform
2. Each time you fill the tank, record the amount of fuel added (ingallons or liters).3. After at least three to five tank fill-ups, fill the fuel tan
• Warming up a vehicle on cold mornings is not required and mayreduce fuel economy.• Resting your foot on the brake pedal while driving may reduce fue
It is important to note the box in the lower left corner of the windowsticker. These numbers represent the Range of MPG (L/100 km)expected on the vehi
Do not make any unauthorized changes to your vehicle or engine. Bylaw, vehicle owners and anyone who manufactures, repairs, services,sells, leases, tr
Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect
6. / Play/Pause: This controlis operational in CD and DVD mode(if equipped). When a CD or DVD isplaying in the FES system, press this control to play
1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center o
Transmission fluid should be checked and, if required, fluidshould be added by an authorized dealer.Do not use supplemental transmission fluid additiv
If the original universal joints are replaced with universal joints equippedwith grease fittings, lubrication will be necessary.Note: Your vehicle’s d
MOTORCRAFT PART NUMBERSComponent 4.0L SOHC V6 engine 4.6L 3V V8 engineAir filter element FA-1695 FA-1780Fuel filter FG-1083 FG-1083Battery BXT-65-650
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationBrake fluidBetween MIN an
Item CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine coolant 4.0Lengine without auxiliaryclimate control12.2 quarts(11.5
Item CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine oil 4.6L engine 6.0 quarts (5.7L)Motorcraft SAE 5W-20Premium Synthe
Item CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationFuel tank22.5 gallons(85.2L)——1Add the coolant type originally equipped in
ENGINE DATAEngine 4.0L SOHC V6engine4.6L 3V V8engineCubic inches 245 281Required fuel 87 octane 87 octaneFiring order 1-4-2-5-3-6 1-3-7-2-6-5-4-8Ignit
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
memory presets, tune to the desired channel then press and hold apreset control until sound returns.Satellite radio is available only with a valid SIR
1. World manufacturer identifier2. Brake type and gross vehicleweight rating (GVWR)3. Vehicle line, series, body type4. Engine type5. Check digit6. Mo
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
Peace of mindMobile-Ease娂 hands-free communication systemRemote startVehicle security systemsWheel locksNot all accessories are available for all mode
AAccessory delay ...95AdvanceTrac ...251Air cleaner filter ...352–353Air conditioning ..
washing ...312waxing ...313wheels ...313wiper bl
Engine oil ...325checking and adding ...325dipstick ...325filter, specifica
Illuminated visor mirror ...90Infant seats(see Safety seats) ...200Inspection/maintenance (I/M)testing ...
Passenger OccupantClassification Sensor ...167Pedals (see Poweradjustable foot pedals) ...97Power adjustable foot pedals ...
Special noticeambulance conversions ...8utility-type vehicles ...8Specification chart,lubricants ...
17. LOAD: Toloadadiscintothesystem, press LOAD. Select a slotnumber using memory presets 1–6.When the display reads LOAD CD#,load the desired disc, la
Auxiliary input jackYour vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicpl
Troubleshooting:1. Do not connect the audio input jack to a line level output. Line leveloutputs are intended for connection to a home stereo and are
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
CD/CD player careDo:• Handle discs by their edges only. Never touch the playing surface.• Inspect discs before playing. Clean only with an approved CD
• Creating discs with only one level of folders will help with navigationthrough the disc files.Sample MP3 structureIf you are burning your own MP3dis
• Antenna obstructions: For optimal reception performance, keep theantenna clear of snow and ice build-up and keep luggage and othermaterial as far aw
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m
Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The
Quick startYour Family Entertainment System includes a DVD system, two sets ofwireless infrared (IR) headphones and a wireless infrared (IR) remotecon
1. Ensure that the vehicle ignition is in the RUN or ACCESSORYposition.2. Insert a CD into the system,label-sideuptoturnontheDVDsystem. It will load a
2. Press the power button to turnthe DVD system on. The indicatorlight next to the power button willilluminate.3. Connect an auxiliary audio/videosour
Note: Channel A can access any possible media source (AM, FM1, FM2,SAT (if equipped), CD, DVD, AUX). Channel B can only access DVD andAUX sources.Note
DVD player controls1. Headphone control A/B: Pressto select either the A or Bheadphone source. Then pressMEDIA to select the desired playingmedia for
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
4. (Fast forward): Press andrelease for the next chapter ortrack. Press and hold to forwardsearch a DVD, Video CD, or FES CD in DVD/CD mode.5./ (Play/
11. / (Headphones/Speakers): Press once for Dual Play(Headphone mode- the rear speakers are muted) and press again forSingle Play (same media playing
Remote controlUnless otherwise stated, all operations can be carried out with theremote control. Always point the remote control directly at the playe
7. VOL (Volume): When in Single Play, press to increase ( )ordecrease () the volume over all speakers. When in Dual Play, press toincrease () or decre
22. ENTER: Press to select the highlighted menu option.23. ILLUMINATION: Press to illuminate the remote control andbacklight all of the buttons.Batter
HeadphonesWireless headphonesYour FES system is equipped with two sets of battery powered, infraredwireless headphones. Two AAA batteries are needed t
To operate the headphones:• Press ON/OFF on the ear piece toturn on the headphones. A redindicator light will illuminateindicating the headphones areO
Channel A source. The wired headphone jack for Channel B is located onthe right side of the FES and is labeledB. Headphones plugged intothis headphone
Press the Headphone Control buttonA to change the audio source forChannel A.Press MEDIA to change the audiosource for Channel A. Thisinformation will
Menu modePress MENU once on the DVD system to access the DVD disc menu ifavailable.Press MENU twice to access the DVD set-up menu and the followingfea
BREAKING-IN YOUR VEHICLEYour vehicle does not need an extensive break-in. Try not to drivecontinuously at the same speed for the first 1,000 miles (1,
You can select from: WIDE, LETTERBOX or PAN SCAN. Once you havemade your selection, press ENTERto confirm. The LCD screen displaywill immediately chan
Once you have made your selection,press ENTER to confirm. This isdisc dependent.Audio CDsTo play audio CDs on your DVD system:1. Ensure that the vehic
4. The folder, track and elapsedtime will appear in the status bar.The screen will list the Artist, Title,Album and File Name.COMP (Compression):Compr
CD, MP3 and CD player care• Handle discs by their edges only. Never touch the playing surface.• Do not expose discs to direct sunlight or heat sources
4. Use the DVD bezel controls to:Press to play or pause a DVD.Press to stop or eject a DVD.Press and release to go to theprevious chapter. Press and h
Frame by frame1. With a DVD playing, press pause.2. Press the right cursor button. TheDVD will advance one frame. Eachpress of the right cursor button
The B headphone jack (5) is locatedon the right side of the DVD system.Plug in wired headphones (notincluded) here.Note: The B headphones can onlyacce
FULL (enabled): The FES has control over the primary (speaker) andsecondary (headphone) audio sources.LOCAL: The FES has control over the secondary so
Do not leave children unattended in the vehicle and do not letchildren operate the system while unsupervised. If wiredheadphones or auxiliary systems
Federal Communication Commission (FCC) ComplianceChanges or modifications not approved by Ford Lincoln-Mercury couldvoid user’s authority to operate t
Service Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This pote
Foreign substancesExercise care to prevent dirt and foreign objects from entering the DVDplayer compartment. Be especially careful not to spill liquid
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM(IF EQUIPPED)1. A/C control: Manually turns A/Con or off.2. Recirculation control: Coolsthe vehicle mo
control of their individual temperature settings (dual zone control). Pressto turn on dual zone mode, press again to return to single zone.6.: Distrib
16. EXT: Displays the outside airtemperature. It will remaindisplayed until the EXT control ispressed again. The external temperature will be most acc
Do not place objects on top of the instrument panel as theseobjects may become projectiles in a collision or sudden stop.AUXILIARY SYSTEM (IF EQUIPPED
REAR WINDOW DEFROSTERThe rear defroster control is locatedon the instrument panel.Press the rear defroster control toclear the rear window of thin ice
the engine is cold and running at higher rpms associated with cold starts.This rpm increase is required to provide adequate power from thealternator t
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola
Notice to owners of pickup trucks and utility type vehiclesUtility vehicles have a significantly higher rollover rate thanother types of vehicles.Befo
Push the headlamp control towards the instrument panel to deactivatethe foglamps.Daytime running lamps (DRL) (if equipped)To activate DRL:• the igniti
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel when exteriorlights are on.• Rotate the thumbwheel from leftto right to bright
3. Turn on the low beam headlamps.The brightest part of the lightshould be below the horizontal line(4). If it is above the line theheadlamp will need
INTERIOR LAMPSDome/reading lampsThe dome lamp lights when:• any door is opened.• the instrument panel dimmerswitch is rotated up until thecourtesy lam
Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an
Replacing headlamp bulbsDo not touch the glass of a halogen bulb.1. Turn off the headlamps and openthe hood.2. Remove three screws from theheadlamp as
Replacing front parking lamp/turn signal/sidemarker bulbs1. Turn off the headlamps and openthe hood.2. Remove three screws from theheadlamp assembly a
4. Rotate the bulb socketcounterclockwise and remove itfrom the lamp assembly.5. Pull the bulb straight out of thesocket.Reverse steps to reinstall bu
Replacing high-mount brakelamp bulb1. Remove the two screws and lampassembly away from the vehicle.2. Remove the bulb holder from thelamp assembly by
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
Export unique (Non–United States/Canada) vehicle specificinformationFor your particular global region, your vehicle may be equipped withfeatures and o
OFF — Rear wiper and washer off.For rear wash cycle, rotate (and hold as desired) the rear wiper/washercontrol to eitherposition.From either position,
Slide on rod featureRotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage.Note: To stow the visor back intoth
Installing a garage door opener (if equipped)The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers:• Pla
Use only soft cups in the cupholder. Hard objects can injure youin a collision.Rear center console features (if equipped)The rear center console incor
Always keep the power point caps closed when not being used.Cigar/Cigarette lighter (if equipped)Do not plug optional electrical accessories into the
One touch downAllows the driver’s window to openfully without holding the controldown. Push the switch completelydown to the second detent andrelease
EXTERIOR MIRRORSPower side view mirrorsThe ignition must be in the ACC or ON position to adjust the power sideview mirrors.To adjust your mirrors:1. R
POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is
3. Press the SET + control andrelease it.4. Take your foot off the acceleratorpedal.5. The indicator lighton theinstrument cluster will turn on.Note:•
Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET + controluntil you get to the desiredspeed,
Commentaires sur ces manuels