Ford 2007 Explorer Sport Trac v.2 Manuel d'utilisateur

Introduction 4Instrument Cluster 10Warning lights and chimes 10Gauges 16Entertainment Systems 19How to get going 19AM/FM stereo with CD 23AM/FM stereo

WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may

To remove the cargo cage:1. Extend the cargo cage.2. Pull the lever on each side of thecage to unlock it.Make sure the locking clip screwsare loose be

To open the rear panel:• Open the lock cover and unlockthe rear panel using the Tonneaucover key.• Lift the rear panel to access itemsin the pickup bo

Interior tonneau cover releaseYour vehicle is equipped with a mechanical interior tonneau coverrelease handle that provides a means of escape for chil

CARGO AREA FEATURESCargo management systemThe cargo management system consists of a storage compartmentlocated in the floor of the pickup box.The stor

Interior tiedown hooksMounted inside the pickup box,each tiedown hook can secure loadsup to 200 lb. (90 kg). Total pickupbox cargo weight is not to ex

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.

KEYSOne key operates the door and tailgate locks and starts the vehicle. Thetonneau cover (if equipped) uses a unique key. Always carry a spare keywit

Deactivating/activating autolockYour vehicle comes with the autolock feature enabled. There are fourmethods to enable/disable this feature:• Through y

4. Press and hold the 3 • 4. While holding the 3 • 4pressthe7• 8.5. Release the 7 • 8.6. Release the 3 • 4.The user should receive a horn chirp to ind

Power door unlock/lock procedureYou must complete Steps 1-5 within30 seconds or the procedure willhave to be repeated. If theprocedure needs to be rep

Note: Some Warning Lights will display in the Message Center as wordsand function the same as the warning light.Note: Depending on which options your

Power door lock/unlock inhibit feature (if equipped)If the key is not in the ignition, all doors are closed, and the vehicle hasbeen locked using the

CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the

Your vehicle is equipped with a remote entry system which allows you to:• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta

Locking the doors1. Press and release to lock all the doors. The lamps will flash. Note:If any door is not closed properly, the lamps will not flash u

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery. Note: Please refer to local r

Note: Ensure the brake pedal is notdepressed during this sequence.To reprogram the remote entrytransmitters:1. Ensure the vehicle is electronically un

The inside lights will not turn off if:• they have been turned on with the dimmer control, or• any door is open.The battery saver will shut off the in

Tips:• Do not set a code that uses five of the same number.• Do not use five numbers in sequential order.• The factory set code will work even if you

SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEMSecuriLock娂 passive anti-theft system is an engine immobilizationsystem. This system is designed to help prevent

Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 2(ACCESSORY) position.The theft indicator will flash everytwo seco

• Optional instrument clusterBrake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when the

Please read and understand theentire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition.2. Turn the igniti

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

Push control to lower head restraint.Adjusting the front manual seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving

Using the manual lumbar support (if equipped)For more lumbar support, turn thelumbar support control toward thefront of vehicle.For less lumbar suppor

To reduce the risk of possible serious injury: Do not hang objectsoff seat back or stow objects in the seatback map pocket (ifequipped) when a child i

Press the control to recline theseatback forward or rearward.Using the power lumbar support (if equipped)The power lumbar control is located on the ou

REAR SEATSFolding down the 2nd row 60/40 seatsEnsure that the head restraint is in the down position and no objectssuch as books, purses or briefcases

3. Lift up on the head restraint untilit locks into its original position.Before returning the seatback to its original position, make surethat cargo

How does the Personal Safety System姟 work?The Personal Safety System娂 can adapt the deployment strategy of yourvehicle’s safety devices according to c

because they are initially sitting very close to the airbag. For otheroccupants, this occurs when the occupant is not properly restrained bysafety bel

Safety belt: Reminds you to fastenyour safety belt. A BeltMinder威chime will also sound to remind youto fasten your safety belt. Refer tothe Seating an

Front safety belt energy management retractorsThe front outboard safety belt energy management retractors allowwebbing to be pulled out of the retract

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.All

• This safety belt system has a retractor assembly that is designed toextend the safety belt webbing in a controlled manner. This helpsreduce the belt

All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of l

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl

Safety belt pretensionerYour vehicle is equipped with safety belt pretensioners at the driver andright front passenger seating positions.The safety be

Second row comfort guideThe second row outboardlap/shoulder belt is equipped with abelt comfort guide. This guide isattached to the quarter trim panel

Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label.

Both the driver’s and passenger’s safety belt usages are monitored andeither may activate the BeltMinder威 feature. The warnings are the samefor the dr

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra

Never remove the coolant reservoir cap while the engine isrunning or hot.Low tire pressure warning:Illuminates when your tire pressureis low. If the l

Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate

• The ignition switch is in the OFF position• The driver and front passenger safety belts are unbuckledWhile the design allows you to deactivate your

Safety belt maintenanceInspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to ma

Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in

Do not attempt to service, repair, or modify the airbagsupplemental restraint systems or its fuses. See your authorizeddealer.Modifications to the fro

How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suffic

Several air bag system components get hot after inflation. Do nottouch them after inflation.If the air bag has deployed, the air bag will not function

The front passenger sensing system will disable (will not inflate) thefront passenger’s frontal airbag if:• the front passenger seat is unoccupied, or

• When the front passenger sensing system enables the front passengerfrontal airbag (may inflate), the indicator will be unlit and stay unlit.If a per

The front passenger sensing system may detect small or medium objectsplaced on the seat cushion. For most objects that are in the frontpassenger seat,

AdvanceTrac威: Flashes when theAdvanceTrac威 with RSC system isactive. Illuminates solid when thesystem has been disabled (by thedriver or as a result o

To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a child is in

Any alteration/modification to the front passenger seat mayaffect the performance of the front passenger sensing system.Determining if the system is o

Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See yourauthorized dealer.All

The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuittha

Do not lean your head on the door. The Safety Canopy娂 couldinjure you as it deploys from the headliner.Do not attempt to service, repair, or modify th

• A headliner that will flex to open above the side doors to allow SafetyCanopy娂 deployment.• The same warning light, electronic control and diagnosti

If the Safety Canopy娂system has deployed, theSafety Canopy娂 will notfunction again. The SafetyCanopy娂 system (including theA, B and C pillar trim) mus

Important child restraint precautionsYou are required by law to use safety restraints for children in the U.S.and Canada. If small children (generally

Child booster seatsChildren outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the la

Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi

Turn signal: Illuminates when theleft or right turn signal or thehazard lights are turned on. If theindicators stay on or flash faster, check for a bu

If needed, when installing some high back child restraints, the headrestraints of the second row seating positions can be removed. Insert athin pointe

Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in acollision.SAFETY SEATS F

tether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. Formore info

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a

Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a

3. Locate the correct anchor for theselected rear seating position.• You may need to pull the seatback forward to access the tetheranchors. Make sure

5. Clip the tether strap to theanchor and return the seat back toits locked position. For Adrenalinvehicles fixed left rear seat, clip thetether hook

Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol:Never attach two LATCH child safe

Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,

’The anchors on the 2nd row outboard seats are provided only to installchild seats at the outboard seats. DO NOT install a child seat at thecenter 2nd

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary.

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air

Label which is located on the B-Pillar or the edge of the driver’s door.The cold inflation pressure should never be set lower than therecommended pres

TIRE CAREInspecting your tiresPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones, nails or glass that

AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressure, etc.)

Trip odometer: Registers the miles (kilometers) of individual journeys.• Standard instrument clusterPress the SELECT/RESET controlonce to switch from

Only use replacement tires and wheels that are the same sizeand type (such as P-metric versus LT-metric or all-season versusall-terrain) as those orig

The tire pressure sensors mounted in the wheels (originally installed onyour vehicle) are not designed to be used in aftermarket wheels.The use of whe

Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your

Note: If your tires show uneven wear ask an authorized dealer to checkfor and correct any wheel misalignment, tire imbalance or mechanicalproblem invo

4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new

8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n

13. Maximum Permissible Inflation Pressure: Indicates the tiremanufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

Changing tires with TPMSEach road tire is equipped witha tire pressure sensor fastenedto the inside rim of the wheel.The pressure sensor is coveredby

AUDIO SYSTEMSQuick start — How to get goingListening to the radio1. If the audio system is off, pressVOL-PUSH to turn the radio on.Turn VOL-PUSH to ad

When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.

When inflating your tiresWhen putting air into your tires (such as at a gas station or in yourgarage), the Tire Pressure Monitoring System may not res

Follow these guidelines when using snow tires and traction devices:• Use only SAE Class S chains.• Cables should only be used on the rear wheels.• Ins

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury.Steps for determining the correct l

• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the l

TRAILER TOWINGTrailer towing with your vehicle may require the use of a trailer towoption package.Trailer towing puts additional loads on your vehicle

Seating and Safety Restraints 121Seating 121Safety restraints 127Airbags 142Child restraints 156Tires, Wheels and Loading 171Tire information 173Tire

2. Press AUX repeatedly to cyclethrough auxiliary audio sources.Select SAT1, SAT2 or SAT3 to listento satellite radio.3. PressSEEK, SEEK toaccess the

4x2GCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.0L SOHC Class

4WDGCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axleratioMaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.0L SOHCClass II

Safety chainsAlways connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cr

Driving while you towWhen towing a trailer:• Keep your speed no faster than 70 mph (112 km/h) during the first500 miles (800 km) of towing a trailer,

• If you will be towing a trailer frequently in hot weather, hillyconditions, at GCWR, or any combination of these factors, considerrefilling your rea

RECREATIONAL TOWING (ALL WHEELS ON THE GROUND)Follow these guidelines for your specific powertrain combination to towyour vehicle with all four wheels

STARTINGPositions of the ignition1. OFF/LOCK, shuts off the engineand all accessories/locks the steeringwheel, gearshift lever and allows keyremoval.2

If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf

• Make sure the gearshift is in P(Park).3. Turn the key to 3 (ON) withoutturning the key to 4 (START).Some warning lights will briefly illuminate. See

Starting the engine1. Turn the key to 3 (ON) withoutturning the key to 4 (START). Ifthere is difficulty in turning the key,rotate the steering wheel u

For an in-dash six CD system, ifa disc is not already loaded, pressLOAD. Select a slot number usingmemory presets 1–6. When thedisplay reads LOAD CD#,

To reduce the risk of electrical shock, do not use your heaterwith ungrounded electrical systems or two-pronged (cheater)adapters.BRAKESOccasional bra

Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.ADVANCETR

If your vehicle should become stuck in deep snow or mud, try switchingthe AdvanceTrac威 with RSC system off by pressing the AdvanceTrac威with RSC button

• Driving on slick surfaces.• Cornering while towing a heavily loaded trailer (refer to Trailertowing in the Tires, Wheels and Loading chapter.)Roll S

If the vehicle is above 25 mph (40 km/h), momentarily pressing theAdvanceTrac威 with RSC button will steadily illuminate the “sliding car”icon, however

Aggressive driving in any road conditions can cause you to losecontrol of your vehicle increasing the risk of severe personalinjury or property damage

PREPARING TO DRIVEUtility vehicles have a significantly higher rollover rate thanother types of vehicles.In a rollover crash, an unbelted person is si

2. Remove the rubber pad at thebottom of the cup holder to locatethe access cap of the floor shifterassembly.3. Using a screwdriver (orequivalent), re

Driving with a 5–speed automatic transmission (if equipped)This vehicle is equipped with an Adaptive Transmission Control Strategy.This Adaptive Trans

Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random pl

P (Park)This position locks the transmissionand prevents the rear wheels fromturning.To put your vehicle in gear:• Start the engine• Depress the brake

D (Drive) without OverdriveOverdrive can be deactivated bypressing the transmission controlswitch on the side of the gearshiftlever.• This position al

Forced downshifts• Allowed in D (Overdrive) or Drive.• Depress the accelerator to the floor.• Allows transmission to select an appropriate gear.Drivin

P (Park)This position locks the transmissionand prevents the rear wheels fromturning.To put your vehicle in gear:• Depress the brake pedal• Start the

D (Drive) without OverdriveOverdrive can be deactivated bypressing the transmission controlswitch on the side of the shift lever.• This position allow

• Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds.Forced downshifts• Allowed in D (Drive) onl

Certain add-on devices such as large trailer hitches, bike orsurfboard racks and any device that may block the normaldetection zone of the RSS system

If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement

4X4 HIGH (4WD High) - Provides locked four-wheel drive power to allfour wheels. This mode is not intended for use on dry pavement. Thismode is appropr

Drive cautiously to avoid vehicle damage from concealed objects such asrocks and stumps.You should either know the terrain or examine maps of the area

AM/FM Single CD/MP3 satellite compatible sound system(if equipped)Accessory delay: Your vehicle is equipped with accessory delay. Withthis feature, th

If your vehicle gets stuckIf your vehicle gets stuck in mud or snow it may be rocked out byshifting between forward and reverse gears, stopping betwee

ParkingOn some 4WD vehicles, when the transfer case is in the N (Neutral)position, the engine and transmission are disconnected from the rest ofthe dr

Note: If your vehicle is equipped with the Tire Pressure MonitoringSystem (TPMS), the system indicator light may illuminate depending onhow much air i

“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nationswilderness are

Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;

Never drive with chains on the front tires of 4WD vehicles without alsoputting them on the rear tires. This could cause the rear to slide andswing aro

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

Canadian customers refer to your Owner Information Guide forinformation on:• coverage period• exact fuel amounts• towing of your disabled vehicle• eme

HAZARD FLASHERThe hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is

The fuel pump shut-off switch islocated in the passenger’s foot well,by the kick panel.Use the following procedure to reset the fuel pump shut-off swi

3. MENU: Press repeatedly toaccess the following settings:CATEGORY (satellite radio if equipped):: Press MENU until thecurrently active category appea

Note: Always replace a fuse with one that has the specified amperagerating. Using a fuse with a higher amperage rating can cause severe wiredamage and

Passenger compartment fuse panelThe fuse panel is located below theinstrument panel on the driver’sside.To remove a fuse use the fuse puller tool prov

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description7 15A Trailer tow stop/turn lamps8 15A Ignition switch power, PATS9 2A 6-sp

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description25 15A Trailer tow park lamps, Trailertow electronic brake module26 15A Lic

To reduce risk of electrical shock, always replace the cover tothe Power Distribution Box before reconnecting the battery orrefilling fluid reservoirs

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription10 20A** Power down back window11 30A** Starter12 — Not used13 30A** Trailer tow batt

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription38 15A* 5–speed transmission39 15A* PCM power40 15A* Fan clutch, PCV valve (4.0Lengin

• hold the steering wheel firmly.• slowly move to a safe place on the side of the road.Note: The tire pressure monitoring system (TPMS) indicator ligh

When driving with one of the dissimilar spare tires listed above, do not:• Exceed 50 mph (80 km/h)• Load the vehicle beyond maximum vehicle load ratin

• Winter weather driving capability• Wet weather driving capability• All-Wheel driving capability (if applicable)• Load leveling adjustment (if applic

SPEED VOL (Speed sensitive volume, if equipped): Press MENU toreach the SPEEDVOL setting. Radio volume automatically gets louderwith increasing vehicl

Location of the spare tire and toolsThe spare tire and tools for your vehicle are stowed in the followinglocations:Tool LocationSpare tire Under the v

Removing the spare tire1. Assemble the jack handle to thelug wrench by sliding the squareend of the jack handle through theplastic grommet on the lug

If the vehicle slips off the jack, you or someone else could beseriously injured.Do not attempt to change a tire on the side of the vehicle closeto mo

4. Position the jack according to theillustrated guides and turn the jackhandle clockwise until the tire is amaximum of 1 inch (25 mm) off theground.T

8. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torquespecifications later in this chapterfor the proper lu

Stowing the jack and tools1. Unblock the wheels.2. Stow the wheel ornament (if removed) in a safe location in the vehicle(such as the glove box or jac

Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted.Do not attempt to push-start your automatic transmissionvehicle. A

1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations, lightning bolts are used to

4. Make the final connection of the negative (-) cable to the ground studlocated toward the front of the vehicle (forward of the battery) on theradiat

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa

5. SEEK: In radio mode,press/ to access theprevious/next strong station.In CD mode, press/ toaccess the previous/next CD track.In satellite radio mode

4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery.After the disabled vehicle has been started and the jumper

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

information is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the

Or call:For a free publication catalog, order toll free: 1-800-782-4356Monday-Friday 8:00 a.m. - 6:00 p.m. ESTHelm, Incorporated can also be reached b

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

8. FOLDER : In folder mode,press FOLDERto access nextfolder on MP3 discs, if available.9.FOLDER: In folder mode,press FOLDER to access theprevious fol

WAXINGApplying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage.• Wash the ve

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

4.0L SOHC V6 Engine4.6L V8 Engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTIC (N

coatings, tree sap, or other organic contamination; these contaminantsmay cause squeaking or chatter noise from the blades, and streaking andsmearing

INTERIOR TRIM• Clean the interior trim areas with a damp cloth, then with a clean, drycloth.• Do not use household or glass cleaners as these may dama

• Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl and plastics, or oil/petroleum-basedleathe

Motorcraft Premium Liquid Wax (ZC-53-A)Motorcraft Premium Windshield Washer Concentrate (ZC-32–A)Motorcraft Professional Strength Carpet & Upholst

SERVICE RECOMMENDATIONS• Use the scheduled maintenance information to track routineservice.• Use only recommended fuels, lubricants, fluids and servic

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.0L SOHC V6 engine1. Engine oil filler cap2. Engine oil dipstick (out of view)3. Brake fluid reservoi

In satellite radio mode (if equipped), press and hold to hear a briefsampling of the next channels. Press again to stop. In CATEGORYMODE, press SCAN t

4.6L V8 engine1. Air filter assembly2. Engine oil filler cap3. Engine oil dipstick4. Brake fluid reservoir5. Power distribution box6. Battery7. Power

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas

• 4.0L V6 engine• 4.6L V8 engine6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.• If the oil level is between the lower a

• 4.0L V6 engine• 4.6L V8 engine• Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized de

To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level indicator and/or the engine oil filler cap removed.Engine Oil Recommen

4.6L 3V V8 EngineLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by the AmericanPetroleum

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyeswhen working near

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

Audiophile AM/FM in-dash six CD/MP3 satellite compatible soundsystem (if equipped)Accessory delay: Your vehicle is equipped with accessory delay. With

• 4.0L V6 engine• 4.6L V8 engine• The engine coolant should be at the “FULL COLD” level as listed onthe engine coolant reservoir (depending upon appli

Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservo

For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when

Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i

Oil overheat can be triggered in severe driving conditions, such astowing heavy loads over mountainous terrain in extreme hottemperatures. As oil temp

The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stopsbefore completely rem

• Be particularly careful if you are taking “Antabuse” or other forms ofdisulfiram for the treatment of alcoholism. Breathing gasoline vapors,or skin

Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1/4 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref

If you do not use the proper fuel filler cap, excessive vacuum inthe fuel tank may damage the fuel system or cause the fuel capto disengage in a colli

Maintenance and Specifications 277Engine compartment 279Engine oil 282Battery 287Engine coolant 289Fuel information 295Air filter(s) 309Part numbers 3

2. MUTE/ : Press to mute theplaying media. Press again to returnto the playing media.3. MENU: Press repeatedly toaccess the following settings:CATEGOR

Do not be concerned if your engine sometimes knocks lightly. However, ifit knocks heavily under most driving conditions while you are using fuelwith t

• The indicator may come on. For more information on the “checkengine” or the “service engine soon” indicator, refer to Warning lightsand chimes in th

• Have the vehicle loading and distribution the same every time.Your results will be most accurate if your filling method is consistent.Calculating fu

• Revving the engine before turning it off may reduce fuel economy.• Using the air conditioner or defroster may reduce fuel economy.• You may want to

EPA window stickerEvery new vehicle should have the EPA window sticker. Contact yourauthorized dealer if the window sticker is not supplied with your

Exhaust leaks may result in entry of harmful and potentiallylethal fumes into the passenger compartment.Do not make any unauthorized changes to your v

If the indicator remains on, have your vehicle serviced at the firstavailable opportunity. Although some malfunctions detected by theOBD-II may not ha

POWER STEERING FLUIDCheck the power steering fluid. Refer to scheduled maintenanceinformation for the service interval schedules. If adding fluid isne

TRANSMISSION FLUIDChecking automatic transmission fluidThe automatic transmission does not have an underhood transmissionfluid dipstick.Refer to your

DRIVELINE UNIVERSAL JOINT AND SLIP YOKEIf the original universal joints are replaced with universal joints equippedwith grease fittings, lubrication w

To search for specific RBDS music categories: When the desiredcategory appears in the display, press/ to find the desired type,then press and releaseS

MOTORCRAFT PART NUMBERSComponent 4.0L SOHC V6 engine 4.6L 3V V8 engineAir filter element FA-1695 FA-1780Fuel filter FG-1083 FG-1083Battery BXT-65-650

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationBrake fluidFill to line o

Item CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine oil 4.0L engine 5.0 quarts (4.7L)Motorcraft SAE 5W-30Premium Synthe

Item CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationTransfer case fluid(4WD)1.5 quarts (1.4L)Motorcraft MERCON威Multi-Purpose A

ENGINE DATAEngine 4.0L SOHC V6engine4.6L 3V V8engineCubic inches 245 281Required fuel 87 octane 87 octaneFiring order 1-4-2-5-3-6 1-3-7-2-6-5-4-8Ignit

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

6. Model year7. Assembly plant8. Production sequence numberTRANSMISSION/TRANSAXLE CODE DESIGNATIONSYou can find atransmission/transaxle code on theSaf

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

LifestyleAsh cup / smoker’s packageCargo organization and managementTrailer hitches, wiring harnesses and accessoriesPeace of mindMobile-ease娂 hands-f

AAccessory delay ...64AdvanceTrac ...212Air cleaner filter ...309–310Air conditioning ..

COMPRESS (Compression): Available only in CD/MP3 mode. PressMENU until COMPRESS ON/OFF appears in the display. Use/ /SEEK, SEEK to toggle ON/OFF. When

wheels ...270wiper blades ...272Climate control (see Airconditioning or Heating) ...

Exhaust fumes ...209FFail safe cooling ...294Floor mats ...97Fluid capacit

autolock ...106, 108keypad ...116locking and unlocking doors ..117programming entry code ...

Relays ...239Remote entry system ...111–112illuminated entry ...115locking/unlockingdoors ..

sidewall information ...183snow tires and chains ...191spare tire ...247, 250terminology ...

325

326

327

328

6. / Play/Pause: This controlis operational in CD and DVD mode(if equipped). When a CD or DVD isplaying in the FES system, press this control to play

In satellite radio mode (if equipped), there are 18 available presets,six each for SAT1, SAT2 and SAT3. To save satellite channels in yourmemory prese

16. CD: Press to enter CD/MP3mode. If a disc is already loadedinto the system, CD/MP3 play willbegin where it ended last. If no CD is loaded, NO DISC

Auxiliary input jackYour vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicpl

Troubleshooting:1. Do not connect the audio input jack to a line level output. Line leveloutputs are intended for connection to a home stereo and are

CD/CD player careDo:• Handle discs by their edges only. Never touch the playing surface.• Inspect discs before playing. Clean only with an approved CD

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required. Thism

Radio Display Condition Action RequiredNO TEXT Category informationnot available.Category information notavailable at this time onthis channel. The sy

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele

• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield.• To improve the A/C cool down when the vehicle interior issign

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM(IF EQUIPPED)1. A/C control: Press to turn onthe air conditioning. Press again toturn off the air cond

4. MAX A/C: Distributesrecirculated air through theinstrument panel vents to cool thevehicle. This recooling of theinterior air is more economical and

14. Driver’s side temperaturecontrol: Press to increase ordecrease the temperature on thedriver side of the cabin. This controlalso sets the passenger

To allow side window defogging and demisting while warming up thevehicle cabin:1. Select.2. Select A/C.3. Set the temperature control to maintain comf

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola

Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti

Push the headlamp control towards the instrument panel to deactivatethe foglamps.Daytime running lamps (DRL) (if equipped)To activate DRL:• the igniti

PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel when exteriorlights are on.• Rotate the thumbwheel from leftto right to bright

3. Turn on the low beam headlamps.The brightest part of the lightshould be below the horizontal line(4). If it is above the line theheadlamp will need

Cargo/reading lampsThe dome portion of the lamp orthe center light can be turned onwhen the panel dimmer control isrotated past the detent or when ado

Function Number of bulbs Trade numberHeadlamp low & highbeam2H13Front park/turn lamp 2 3457 NAK (amber)Side park/turn lamp 2 194Rear stop/tail/tur

3. Disconnect the electricalconnector.4. Remove the old bulb by turningcounterclockwise and pull it out.Handle a halogen headlamp bulb carefully and k

Replacing tail/brake/turn/backup lamp bulbs1. Turn the headlamp switch to OFFand open the tailgate.2. Remove the two bolts from thelamp assembly.3. Re

Replacing license plate lamp bulbsThe license plate bulbs are locatedbehind the rear bumper. To changethe license plate lamp bulbs:1. Reach behind the

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

TILT STEERING COLUMNPull the lever down and release, tounlock the steering column tilt lock.With the lever in the down position,tilt the steering colu

Please read the section Supplemental restraint system (SRS)in the Seating and Safety Restraints chapter. Failure to followthe specific warnings and in

Slide on rod featureRotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage.Note: To stow the visor back intoth

Installing a garage door opener (if equipped)The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers:• Pla

The auxiliary power point is locatedin the floor console.Do not use the power point foroperating the cigarette lighterelement (if equipped).To prevent

CENTER CONSOLE1. Cupholders2. Tissue holder in lid3. Rear power point4. Large utility compartment has anexterior power point in front of thelid, and i

One touch downAllows the driver’s window to openfully without holding the controldown. Push the switch completelydown to the second detent andrelease

Do not leave children unattended in the vehicle and do not letchildren play with the power down rear window. They mayseriously injure themselves.Press

The following are possible reasons for using the security override:• Ice on the window causing a restriction.• Window unexpectedly reverses.Position r

EXTERIOR MIRRORSPower side view mirrorsThe ignition must be in the ACC or ON position to adjust the power sideview mirrors.To adjust your mirrors:1. R

SPEED CONTROLWith speed control set, you can maintain a speed of 30 mph (48 km/h)or more without keeping your foot on the accelerator pedal. Speedcont

Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RES contro

Notice to owners of pickup trucks and utility type vehiclesUtility vehicles have a significantly higher rollover rate thanother types of vehicles.Befo

Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal. This will not erase your vehicle’s previouslyset

In AM, FM1, or FM2 mode:• PressSEEK toselect preset stations within theselected radio band or press andhold to select the next/previousradio frequency

Press FAN + or - to adjust fanspeed.MOON ROOF (IF EQUIPPED)You can move the glass panel of the moon roof back to open or tilt up(from the closed posit

Bounce back override: To override bounce back, within 2 seconds afterreaching bounce back position, if the switch is held in the close positionthe moo

Info menuThis menu displays the following control displays:• Odometer/Trip Odometer (Trip A and Trip B)• Distance to Empty• Average Fuel Economy• Setu

• Variations in top-off procedure from one fill-up to another• Rounding of the displayed values to the nearest 0.1 gallon (liter)1. Drive the vehicle

The sequence of the system check report and how it appears in themessage center is as follows:1. OIL LIFE RESET2. CHARGING SYSTEM3. WASHER FLUID4. DOO

Units (English/Metric)1. Select this function from theSETUP MENU for the current unitsto be displayed.2. Press and hold theSELECT/RESET control switch

AutolockThis feature automatically locks all vehicle doors when the vehicle isshifted into any gear and when the vehicle is in motion over 13 mph (20k

Oil Life Start Value1. Select this function from theSETUP MENU for the currentdisplay mode.2. Press and hold theSELECT/RESET control switch toreset oi

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

Compass zone adjustment (if equipped)1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn igniti

1. Start the vehicle.2. Locate the reset button on the compass sensor mounted on the baseof mirror.3. To calibrate, press and hold thereset button on

Warning display StatusDoor ajar Warning cannot be resetFuel level low Warning returns after 10 minutesPark brake engagedCheck brake systemCheck park a

CHECK BRAKE SYSTEM. Displayed when the braking system is notoperating properly. If the warning stays on or continues to come on,contact your authorize

An oil change is required whenever indicated by the message center andaccording to the recommended maintenance schedule. USE ONLYRECOMMENDED ENGINE OI

Selectable featuresResetPress the RESET control to selectand reset functions shown in theINFO menu, SETUP menu, textwarnings and reconfigurable tellta

DTE is calculated using a running average fuel economy, which is basedon your recent driving history of 500 miles (800 km). This value is notthe same

Fuel UsedSelecting this function from theINFO menu. “FUEL USED XXX.XGAL” will display the fuel used sincelast reset. The information displayedwill be

System checkSelecting this function from theSETUP MENU causes the messagecenter to cycle through each of thesystems being monitored. For eachof the mo

2. Press RESET control to display“HOLD RESET IF NEW OIL”.3. Press and hold the RESETcontrol for more than 2 seconds. Oillife is set to 100% and “OILCH

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

1. Select this function from theSETUP MENU for the currentlanguage to be displayed.2. Press the RESET control to cyclethe message center through each

AutounlockThis feature automatically unlocks all vehicle doors when the driver’sdoor is opened within 10 minutes of the ignition being turned off.1. T

Most geographic areas (zones) have a magnetic north compass point thatvaries slightly from the northerly direction on maps. This variation is fourdegr

7. Wait 4 seconds when correct zoneis chosen.Compass calibration adjustment (if equipped)Perform compass calibration in an open area free from steel s

Oil life Start Value1. Select this function from theSETUP control for the currentdisplay mode.2. Each press of the RESET controlreduces the value by 1

Warning display StatusDoor ajar Warning cannot be resetFuel level low Warning returns after 10 minutesPark brake engagedCheck brake systemCheck park a

CHECK BRAKE SYSTEM. Displayed when the braking system is notoperating properly. If the warning stays on or continues to come on,contact your authorize

An oil change is required whenever indicated by the message center andaccording to the recommended maintenance schedule. USE ONLYRECOMMENDED ENGINE OI

Tailgate removalYour tailgate is removable to allowmore room for loading.1. Lower the tailgate.2. Use a screwdriver to pry thespring clip (on each con

To extend the cargo cage:1. Lower tailgate.2. Pull the lever on each side of thecargo cage to release it from thepickup box.3. Lift the cargo cage ove