Ford 2007 Edge v.2 Manuel d'utilisateur

Introduction 4Instrument Cluster 10Warning lights and chimes 10Gauges 14Entertainment Systems 17How to get going 17AM/FM stereo with CD 21AM/FM stereo

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A wa

For more information refer to Fuel Information in the Maintenanceand Specifications chapter.Average SpeedSelect this function from the INFO menu to di

Note: If the compass displays ⬙CAL 000000.0 mi⬙ instead of headinginformation, the compass will need to be calibrated. Slowly drive thevehicle in a ci

Trip elapsed drive timeSelect this function from the INFOmenu to display a timer.To operate the Trip Elapsed DriveTime perform the following:1. Press

4. BRAKE FLUID LEVEL5. WASHER FLUID LEVEL6. FUEL LEVEL7. DISTANCE TO EMPTYUnits (English/Metric)1. Select this function from theSETUP menu for the cur

1. To disable/enable the autounlockfeature, select this function from theSETUP MENU.2. Press and hold the RESETcontrol switch to turn theautounlock ON

3. Press and hold the RESETcontrol for 2 seconds to set thelanguage choice.System warningsSystem warnings alert you to possible problems or malfunctio

Warnings StatusLow brake fluid level Warning returns after the ignition keyis turned from LOCK/OFF to RUNLiftgate ajarLow tire pressureTire pressure m

TIRE PRESSURE SENSOR FAULT. Displayed when a tire pressuresensor is malfunctioning, or your spare tire is in use. For moreinformation on how the syste

LIFTGATEThe liftgate area is only intended for cargo, not passengers. You can openand close the liftgate from outside the vehicle. It cannot be opened

CARGO MANAGEMENT SYSTEM (IF EQUIPPED)The cargo management systemconsists of storage compartmentslocated in the floor of the rear cargoarea.1. To open,

Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interiorfloor coverings or other

KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the lo

RECOMMENDED HANDLING OF THE INTEGRATED KEYHEADTRANSMITTER (IKT)To avoid inadvertently activating the remote entry functions of yourvehicle, it is reco

POWER DOOR LOCKS• Press thecontrol to unlock alldoors.• Press thecontrol to lock alldoors.Smart locksThis feature helps to prevent you from locking yo

Deactivating/activating autolock featureYour vehicle comes with the autolock features activated; there are fourmethods to enable/disable this feature:

Keyless entry key pad autolock enable/disable procedure1. Turn the ignition to the 1 (LOCK)position.2. Close all the doors.3. Enter factory–set 5–digi

Power door lock switch autounlock enable/disable procedureBefore starting, ensure the ignition is in the 1 (LOCK) position and allvehicle doors are cl

CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the

The IKT allows you to:• remotely unlock the vehicledoors.• remotely lock all the vehicledoors.• activate the personal alarm.• operate the illuminated

Two stage unlocking may be disabled or re-enabled by simultaneouslypressing theand controls on the IKT for four seconds (disablingtwo stage unlock all

2. Press the SET control on thedriver’s door panel.3. Within 5 five seconds, press thelock or unlock control on theIntegrated keyhead Transmitter andt

Anti-lock brake system: If theABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected, have the systemserviced immediately by

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery. Note: Please refer to local r

The inside lights will not turn off if:• they have been turned on with the dimmer control, or• any door is open.Perimeter lamps illuminated entryWith

5. Turn the ignition back to the 3 (RUN) position. The horn will chirpone time to confirm programming mode has been entered and is active.6. Press the

available from your authorized dealer. You can also create up to three ofyour own 5–digit personal entry codes.When pressing the controls on the keypa

Anti-scan featureIf the wrong code has been entered 7 times (35 consecutive buttonpresses), the keypad will go into an anti-scan mode. This mode disab

Note: Large metallic objects, electronic devices that are used topurchase gasoline or similar items, or a second coded key on the samekey chain may ca

Replacement Integrated Keyless Transmitters (IKT) and coded keysNote: Your vehicle comes equipped with two Integrated KeyheadTransmitters (IKTs). The

Please read and understand theentire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition.2. Turn the igniti

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

Push release button to lower headrestraint.Using the manual lumbar support (if equipped)The lumbar control is located on theside of the seat cushion.L

Wheels and Loading chapter. When the ignition is first turned to ON,the light will illuminate for 3 seconds to ensure the bulb is working. Ifthe light

Lift handle to move seat forward orbackward.Pump the handle upwards to raisethe cushion and pump downward tolower the cushion to the desiredlocation.P

3. Pull up on the recliner handlelocated on the outboard side of theseat to fold the front passengerseatback.4. Without releasing the handle,push the

Sitting improperly out of position or with the seat back reclinedtoo far can take off weight from the seat cushion and affect thedecision of the front

Memory seat and mirrors (if equipped)This system allows automaticpositioning of the driver seat andoutside rearview mirrors, to twoprogrammable positi

Heated seats (if equipped)The heated seats will only function when the ignition is in RUN.To operate the heated seats:• Push the control located on th

Folding down the 60/40 rear seatsNote: The head restraints should be placed in the full down positionbefore folding the seatback down.Note: Ensure tha

Press and hold the controlmechanism to lower the seatback.The top portion lowers the right(40%) seatback, and the bottomportion lowers the left (60%)s

Seat mounted armrest and cupholdersYour vehicle is equipped with a rearseat armrest. To fold the armrestdown, release the latch located onthe seatback

SAFETY RESTRAINTSPersonal Safety System姟The Personal Safety System娂 provides an improved overall level offrontal crash protection to front seat occupa

longitudinal deceleration. The pretensioners are designed to activate infrontal and near-frontal collisions, and in rollovers and side collisionswhen

High beams: Illuminates when thehigh beam headlamps are turned on.Key-in-ignition warning chime: Sounds when the key is left in theignition in the OFF

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.The front passenger sensing syst

The Restraints Control Module (RCM) monitors its own internal circuitsand the circuits for the airbag supplemental restraints, crash sensor(s),safety

In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a seat belt.Each seating position in your vehicle has

if your vehicle receives an impact of 5 mph (8 km/h) or more, the safetybelt will become locked and help reduce your forward movement.Energy Managemen

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl

Safety belt pretensionerYour vehicle is equipped with safety belt pretensioners at the driver andfront outboard passenger seating positions.The safety

Second row comfort guideThe second row outboardlap/shoulder belt is equipped with abelt comfort guide. This guide isattached to the head restraint and

Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label.

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignition switchis turned to the ON position...The safety belt wa

If... Then...The driver’s and front passenger’ssafety belts are buckled before theignition switch is turned to the ONposition or less than 1-2 minutes

Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature, the needle will be inthe normal range (between “

Reasons given... Consider...“Belts are uncomfortable” We design our safety belts to enhancecomfort. If you are uncomfortable -try different positions

Do not sit on top of a buckled safety belt or insert a latchplateinto the buckle to avoid the Belt-Minder威 chime. To do so mayadversely affect the per

1. Turn the ignition switch to the RUN (or ON) position. (DO NOTSTART THE ENGINE)2. Wait until the safety belt warning light turns off. (Approximately

Important supplemental restraint system precautionsAirbags DO NOT inflate slowly orgently and the risk of injury from adeploying airbag is greatest cl

Do not attempt to service, repair, or modify the airbagsupplemental restraint system (SRS) or its fuses. See yourauthorized dealer.Modifying or adding

How does the safety belt pretensioner and airbag supplementalrestraint system work?The safety belt pretensioner andairbag SRS are designed to activate

Several air bag system components get hot after inflation. Do nottouch them after inflation.If the air bag has deployed, the air bag will not function

The front passenger sensing system will disable (will not inflate) thefront passenger’s frontal airbag if:• the front passenger seat is unoccupied, or

• When the front passenger sensing system enables the front passengerfrontal airbag (may inflate), the indicator lamp will be unlit and stayunlit.If a

Sitting improperly out of position or with the seat back reclinedtoo far can take off weight from the seat cushion and affect thedecision of the front

• With Message CenterRefer to Message Center in theDriver Controls chapter on how toswitch the display from Metric toEnglish.Trip odometer: Registers

To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) orhang objects off seat back if a child is in

Any alteration/modification to the front passenger seat mayaffect the performance of the front passenger sensing system.Determining if the system is o

Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See yourauthorized dealer.All

The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of

Safety Canopy姟 systemDo not place objects ormount equipment on ornear the headliner at the siderailthat may come into contact with adeploying Safety C

How does the Safety Canopy姟 system work?The design and development of theSafety Canopy娂 system includedrecommended testing proceduresthat were develop

close an electrical circuit that initiates Safety Canopy娂 inflation or whena certain likelihood of a rollover event is detected by the rollover sensor

Any difficulty with the system is indicated by one or more of thefollowing:• The readiness airbag light (same light as for front airbag system) willei

Children and safety beltsIf the child is the proper size, restrain the child in a safety seat. Childrenwho are too large for child safety seats (as sp

Booster seats should be used until you can answer YES to ALL of thesequestions:• Can the child sit all the way backagainst the vehicle seat back withk

AUDIO SYSTEMSQuick start — How to get goingListening to the radio1. If the audio system is off, pressVOL-PUSH to turn the radio on.Turn VOL-PUSH to ad

Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto

SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully fo

Carefully follow all of the manufacturer’s instructions includedwith the safety seat you put in your vehicle. If you do not installand use the safety

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a

Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a

4. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safetyseat may not be retained properlyin the even

20 inches (500 mm) apart. Do not attach a child seat to any loweranchor if an adjacent child seat is attached to that anchor.Never attach two LATCH ch

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles handle differentlythan passenger cars in the variousdriving conditions that areencountered

Note: Your AWD vehicle is not intended for off-road use. The AWDfeature gives your vehicle some limited off-road capabilities in whichdriving surfaces

Listening to satellite radio (if equipped)1. If the audio system is turned off,press VOL-PUSH to turn the radioon. Turn VOL-PUSH to adjust thevolume.N

• Narrower — to provide greatermaneuverability in tight spaces.As a result of the above dimensionaldifferences, Utility Vehicles oftenwill have a high

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

Glossary of tire terminology• Tire label: A label showing the OE (Original Equipment) tire sizes,recommended inflation pressure and the maximum weight

Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure of all tires and adjust ifrequired

of 1 psi (7 kPa) in inflation pressure. Check your tire pressuresfrequently and adjust them to the proper pressure which can be foundon the Safety Com

tread grooves. Check for holes or cuts that may permit air leakage fromthe tire and make necessary repairs. Also inspect the tire sidewalls forcrackin

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of thetire to set the beads without ad

If your vehicle is stuck in snow, mud, sand, etc., do not rapidlyspin the tires; spinning the tires can tear the tire and cause anexplosion. A tire ca

• Front Wheel Drive (FWD)/ AllWheel Drive vehicles (front tiresat top of diagram)Sometimes irregular tire wear can be corrected by rotating the tires.

For a single CD system, if a discis not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe

Changing tires with TPMSEach road tire is equipped witha tire pressure sensor fastenedto the inside rim of the wheel.The pressure sensor is coveredby

When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.

Low TirePressureWarning LightPossiblecauseCustomer Action RequiredFlashing WarningLightSpare tire inuseYour temporary spare tire is inuse. Repair the

any tire is under-inflated, carefully drive the vehicle to the nearestlocation where air can be added to the tires. Inflate all the tires to therecomm

Locks and Security 110Keys 110Locks 112Anti-theft system 124Seating and Safety Restraints 128Seating 128Safety restraints 138Airbags 152Child restrain

Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random pl

Vehicle Curb Weight – is the weight of your new vehicle when youpicked it up from your authorized dealer plus any aftermarketequipment.Payload – is th

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle.3. Subtract the combined weight of the driver and pas

1400 - (2 x 220) - (9 x 100) = 1400 - 440 - 900 = 60 lb. Now you havethe load capacity to transport the cement and your friend home. Inmetric units, t

FWDGCWR (Gross Combined Weight Rating)/Trailer WeightEngine MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)Tongueload-lb. (kg)(0-Maximum)3

HitchesDo not use hitches that clamp onto the vehicle’s bumper or attach to theaxle. You must distribute the load in your trailer so that 10%–15% of t

Trailer tow connector(equipped on vehicles with a Class II trailer tow/prep package)The trailer tow connector is located under the rear bumper, on the

• Allow more distance for stopping with a trailer attached.• If you are driving down a long or steep hill, shift to a lower gear. Donot apply the brak

AM/FM Single CD/MP3 satellite compatible sound system(if equipped)Accessory delay: Your vehicle is equipped with accessory delay. Withthis feature, th

All Wheel Drive (AWD) vehicles:Tow your All Wheel Drive vehicle with all four wheels on the ground orwith all four wheels off the ground using a vehic

STARTINGPositions of the ignition1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and a

Do not start your vehicle in a closed garage or in other enclosedareas. Exhaust fumes can be toxic. Always open the garage doorbefore you start the en

• Make sure the gearshift is inP (Park).3. Turn the key to 3 (RUN) withoutturning the key to 4 (START).Some warning lights will briefly illuminate. Se

Note: If the engine does not start within five seconds on the first try,turn the key to LOCK, wait 10 seconds and try again. If the engine stillfails

Refer to Brake system warninglight in the Instrument Clusterchapter for information on the brakesystem warning light.Four-wheel anti-lock brake system

Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th

The Anti-lock Braking System (ABS) will work with the regular brakes inorder to prevent wheel lock during a braking event. This feature will alsohelp

During Electronic Stability Control events the “sliding car” icon in theinstrument cluster will flash momentarily.Driving maneuvers which may activate

The AdvanceTrac威 with RSC button,located on the center stack of theinstrument panel, allows the driverto control certain features of theAdvanceTrac威 w

3. MENU: Press repeatedly toaccess the following settings:CATEGORY (satellite radio if equipped): Press MENU until thecurrently active category appear

• Some noise is normal during operation. If the noise is excessive, checkfor a low power steering fluid level before seeking service by yourauthorized

If you cannot move the gearshift lever out of P (Park) with ignition inthe RUN position and the brake pedal depressed:1. Apply the parking brake, turn

Driving with an automatic overdrive transaxle with columngearshiftYour transaxle is equipped with an adaptive learning strategy found inthe vehicle co

Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position andremove the key wheneve

• O/D (overdrive) is automatically returned each time the key is turnedoff.L (Low)• Provides maximum engine braking.• Will downshift to the lowest ava

Certain add-on devices such as large trailer hitches, bike orsurfboard racks and any device that may block the normaldetection zone of the RSS system

ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED)Your vehicle may be equipped with a full-time All Wheel Drive (AWD)system. With the AWD option, power will b

If your vehicle goes off the edge of the pavement• If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ea

Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle (i.e.,

be required from another vehicle. Remember, you may be able to backout the way you came if you proceed with caution.Mud and waterIf you must drive thr

The default setting is off; increasing your vehicle speed will not changethe volume level.Adjust 1–7: Increasing this setting from 1 (lowest setting)

the route you will use. Do not drive over the crest of a hill withoutseeing what conditions are on the other side. Do not drive in reverseover a hill

Make sure you allow sufficient distance between you and other vehiclesfor stopping. Drive slower than usual and consider using one of the lowergears.

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsUsing roadside assistanceComplete the roadside assi

FUEL PUMP SHUT-OFF SWITCHThis device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt.After an

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 30A Not used (Spare)2 15A Not used (Spare)

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description10 15A Backlighting, Puddle lamps11 10A All wheel drive12 7.5A Power mirror

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description37 10A Climate control38 20A Subwoofer/Amp (Audiophileradio)39 20A Radio40

The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 — Not used2 — Blower motor relay3 — Not

In satellite radio mode (if equipped), press SEEK, SEEK toseek to the previous/next channel. If a specific category is selected,(Jazz, Rock, News, etc

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription15 40A** ABS pump motor16 30A** Front heated seats17 20A** Cigar lighter/Power point1

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription45 — Not used46 15A* Trailer tow right stop/turn lamp47 — Trailer tow right stop/turn

CHANGING THE TIRESIf you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel

2. Full-size dissimilar spare with label on wheel: This spare tire hasa label on the wheel that states: “THIS TIRE AND WHEEL FORTEMPORARY USE ONLY”Whe

The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following:• Handling, stability and braking performance• Comfort and

Removing the spare tire and jack1. Lift the carpeted load floor panellocated in the rear of the vehicle.2. Remove the wing nut securingthe spare tire

Do not attempt to change a tire on the side of the vehicle closeto moving traffic. Pull far enough off the road to avoid thedanger of being hit when o

3. Align the slot on top of the jackwith the sheet metal flangeindicated by the jack locator trianglenext to the tire you are changing.Turn the jack h

Stowing the flat/spare tire and jack1. Fully collapse the jack, fold the wrench socket into the handle andplace the both into the bag making sure to s

JUMP STARTINGThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury orvehicle da

10. FF (Fast forward): Press FFto manually advance in a CD/MP3track.11. REW (Rewind): Press REW tomanually reverse in a CD/MP3 track.12. Memory preset

Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

If the vehicle is towed by other means or incorrectly, vehicledamage may occur.In case of a roadside emergency with a disabled vehicle (without access

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh

14. AM/FM: Press to selectAM/FM1/FM2 frequency band.15. ON/OFF/Volume: Press to turnON/OFF. Turn to increase/decreasevolume.Note: If the volume is set

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio

ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro

To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is

WAXINGApplying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage.• Wash the ve

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENSClean the instrument panel, interior trim areas and cluster lens with aclean and damp white cotton clot

INTERIORFor fabric, carpets, cloth seats and safety belts:• Remove dust and loose dirt with a vacuum cleaner.• Remove light stains and soil with Motor

Audiophile AM/FM in-dash six CD/MP3 satellite compatible soundsystem (if equipped)Accessory delay: Your vehicle is equipped with accessory delay. With

FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column.2. Go to th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.5L V6 engine1. Engine coolant reservoir2. Power steering fluid reservoir3. Brake fluid reservoir4. B

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

Poor wiper quality can be improved by cleaning the wiper blades and thewindshield, refer to Windows and wiper blades in the Cleaningchapter.To prolong

3. Set the parking brake and ensure the gearshift is securely latched inP (Park).4. Open the hood. Protect yourself from engine heat.5. Locate and car

• 3.5L V6 engine• If required, add engine oil to the engine. Refer to Adding engine oilin this chapter.• Do not overfill the enginewith oil. Oil level

Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by th

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If

2. MUTE/ : Press to mute theplaying media. Press again to returnto the playing media.3. MENU: Press repeatedly toaccess the following settings:CATEGOR

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyeswhen working near

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

• Refer to scheduled maintenance information for service intervalschedules.• Be sure to read and understand Precautions when servicing yourvehicle in

• A large amount of water without engine coolant may be added, in caseof emergency, to reach a vehicle service location. In this instance, thecooling

6. Replace the cap. Turn until tightly installed. Cap must be tightlyinstalled to prevent coolant loss.After any coolant has been added, check the coo

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequatefreeze protection at the tempera

Continued operation will increase the engine temperature:• The engine will completely shut down.• Steering and braking effort will increase.Once the e

The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stopsbefore completely rem

• Be particularly careful if you are taking “Antabuse” or other forms ofdisulfiram for the treatment of alcoholism. Breathing gasoline vapors,or skin

Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1/4 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref

To search for specific RBDS music categories: When the desiredcategory appears in the display, press/ to find the desired type,then press and release

If you do not use the proper fuel filler cap, excessive vacuum inthe fuel tank may damage the fuel system or cause the fuel capto disengage in a colli

Fuel qualityIf you are experiencing starting, rough idle or hesitation driveabilityproblems, try a different brand of unleaded gasoline. “Premium”unle

ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform

Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers).2. Each time you fill the tan

• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between the top gears occurs. Unnecessaryshifting of this type co

The EPA window sticker should be your guide for the fuel economycomparisons with other vehicles.It is important to note the box in the lower left corn

Exhaust leaks may result in entry of harmful and potentiallylethal fumes into the passenger compartment.Do not make any unauthorized changes to your v

If the indicator remains on, have your vehicle serviced at the firstavailable opportunity. Although some malfunctions detected by theOBD-II may not ha

POWER STEERING FLUIDCheck the power steering fluid. Refer to the scheduled maintenanceinformation for the service interval schedules.1. Start the engi

TRANSAXLE FLUIDChecking automatic transaxle fluidRefer to your scheduled maintenance information for scheduledintervals for fluid checks and changes.Y

Customer Assistance 256Reporting safety defects (U.S. only) 262Reporting safety defects (Canada only) 263Cleaning 264Maintenance and Specifications 27

COMPRESS (Compression): Available only in CD/MP3 mode. PressMENU until COMPRESS ON/OFF appears in the display. Use/ totoggle ON/OFF. When COMPRESS is

The transmission fluid should bewithin the cross-hatch area if atnormal operating temperature 149°F(65°C).High fluid levelFluid levels above the safe

To reduce the risk of vehicle damage and/or personal burninjuries do not start your engine with the air cleaner removedand do not remove it while the

MOTORCRAFT PART NUMBERSComponent 3.5L V6 EngineEngine air filter element FA-1884Battery BXT-36R 58Ah–Standard orBXT-36R 68Ah (heavyduty)–Trailer tow p

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationBrake fluidBetween MIN andMAX on rese

Item Capacity Ford part nameFord part number /Ford specificationAutomatictransmission fluid10.0 quarts(9.5L)3M otorcraft MERCON威 VATF4XT-5-QM /MERCON威

ENGINE DATAEngine 3.5L-DOHC V6 engineDisplacement 3.5LRequired fuel 87 octaneFiring order 1–4–2–5–3–6Spark plug gap (0.052–0.056 inch) 1.32–1.42 mmIgn

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

Vehicle security systemsWheel locksFor maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your

6. / Play/Pause: This controlis operational in CD and DVD mode(if equipped). When a CD or DVD isplaying in the FES system, press this control to play

AAccessory delay ...90AdvanceTrac ...216Air cleaner filter ...300–302Air conditioning ..

instrument panel ...268interior ...269plastic parts ...266safety belts ...

recommendations ...278refill capacities ...303specifications ...303Event data recording ..

positioning ...242storage ...242Jump-starting your vehicle ...249KKeyless entry syste

Power steering ...219fluid, checking and adding ...298fluid, refill capacity ...303fluid, specifications ...

Tires ...180–181, 242alignment ...188care ...184changing .

316

317

318

319

In satellite radio mode (if equipped), there are 18 available presets,six each for SAT1, SAT2 and SAT3. To save satellite channels in yourmemory prese

320

17. LOAD: To load a disc into thesystem, press LOAD. Select a slotnumber using memory presets 1–6.When the display reads LOAD CD#,load the desired dis

Auxiliary input jack (Line in)Your vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portab

Troubleshooting:1. Do not connect the audio input jack to a line level output. Line leveloutputs are intended for connection to a home stereo and are

CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m

Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The

Quick startYour Family Entertainment System includes a DVD system, two sets ofwireless infrared (IR) headphones and a wireless infrared (IR) remotecon

1. Ensure that the vehicle ignition is in the RUN or ACCESSORYposition.2. Insert a CD into the system,label-side up to turn on the DVDsystem. It will

2. Press the power button to turnthe DVD system on. The indicatorlight next to the power button willilluminate.3. Connect an auxiliary audio/videosour

Note: Channel A can access any possible media source (AM, FM1, FM2,SAT (if equipped), CD, DVD, AUX). Channel B can only access DVD andAUX sources.Note

DVD player controls1. Headphone control A/B: Pressto select either the A or Bheadphone source. Then pressMEDIA to select the desired playingmedia for

4. (Fast forward): Press andrelease for the next chapter ortrack. Press and hold to forwardsearch a DVD, Video CD, or FES CD in DVD/CD mode.5./ (Play/

11. / (Headphones/Speakers): Press once for Dual Play(Headphone mode- the rear speakers are muted) and press again forSingle Play (same media playing

Remote controlUnless otherwise stated, all operations can be carried out with theremote control. Always point the remote control directly at the playe

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

7. VOL (Volume): When in Single Play, press to increase ( )ordecrease () the volume over all speakers. When in Dual Play, pressto increase () or decre

22. ENTER: Press to select the highlighted menu option.23. ILLUMINATION: Press to illuminate the remote control andbacklight all of the buttons.Batter

HeadphonesWireless headphonesYour FES system is equipped with two sets of battery powered, infraredwireless headphones. Two AAA batteries are needed t

To operate the headphones:• Press ON/OFF on the ear piece toturn on the headphones. A redindicator light will illuminateindicating the headphones areO

Channel A source. The wired headphone jack for Channel B is located onthe right side of the FES and is labeledB. Headphones plugged intothis headphone

Press the Headphone Control buttonA to change the audio source forChannel A.Press MEDIA to change the audiosource for Channel A. Thisinformation will

Press MENU twice to access the DVD set-up menu and the followingfeatures:1. ZOOM2. ANGLE3. ASPECT RATIO4. LANGUAGE5. SUB TITLESAngle modeSelect ANGLE

You can select from: WIDE, LETTERBOX or PAN SCAN. Once you havemade your selection, press ENTERto confirm. The LCD screen displaywill immediately chan

Once you have made your selection,press ENTER to confirm. This isdisc dependent.Audio CDsTo play audio CDs on your DVD system:1. Ensure that the vehic

4. The folder, track and elapsedtime will appear in the status bar.The screen will list the Artist, Title,Album and File Name.COMP (Compression):Compr

SPECIAL NOTICESNew Vehicle Limited WarrantyFor a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited

CD, MP3 and CD player care• Handle discs by their edges only. Never touch the playing surface.• Do not expose discs to direct sunlight or heat sources

4. Use the DVD bezel controls to:Press to play or pause a DVD.Press to stop or eject a DVD.Press and release to go to theprevious chapter. Press and h

2. Press the right cursor button. TheDVD will advance one frame. Eachpress of the right cursor button willadvance the DVD video by oneframe.Headphone/

Audio displaysYour DVD system interacts closely with the front audio system. Statusmessages will appear in the radio display showing the DVD status. S

When the DVD system is ON, youcan then press the memory presetcontrols 2 and 4 simultaneously totoggle between Single Play and Dual Play. In Single Pl

The front glass on the liquid crystal display (LCD) flip-downscreen may break when hit with a hard surface. If the glassbreaks, do not touch the liqui

However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interferenceto radio

Cleaning the liquid crystal display (LCD) flip-down screenClean the display screen by applying a small amount of water or anyammonia-based household g

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele

5. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. Engagesautomatically in

• where the driver was positioning the steering wheel.To access this information, special equipment must be directly connectedto the recording modules

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEMWITH HEATED SEATS (IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer

6. Recirculated air: Press to activate/deactive air recirculation inthe vehicle. Recirculated air may reduce the amount of time needed tocool down the

14. EXT: Press to display outside temperature. Press again to displaycabin temperature settings. Note: Exterior readings are more accuratewhen the veh

Do not place objects on top of the instrument panel as theseobjects may become projectiles in a collision or sudden stop.REAR WINDOW DEFROSTERRThe rea

HEADLAMP CONTROLRotate the headlamp control to thefirst positionto turn on theparking lamps. Rotate to the secondpositionto turn on theheadlamps.Autol

Foglamp control (if equipped)The headlamp control also operatesthe foglamps. The foglamps can beturned on when the headlampcontrol is in the, orpositi

Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Lamp (DRL) systemdoes not activate the tail lamps an

• (1) 8 feet (2.4 meters)• (2) Center height of lamp toground• (3) 25 feet (7.6 meters)• (4) Horizontal reference line2. Measure the height of thehead

TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSFront row map lamps (if equipp

Rear courtesy lampLocated in the rear cargo area, thecourtesy lamp lights when:• any door is opened.• any of the remote entry controlsare pressed and

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

Function Number of bulbsTradenumberMap lamp 2 12V6WSecond row dome/readinglamp3 578Rear courtesy lamp 1 1600XBVisor vanity lamp - Slideon Rail system

5. Disconnect the electricalconnector from the bulb.6. Connect the electrical connectoron the bulb.Handle a halogen headlamp bulb carefully and keep o

Replacing tail/stop/turn/sidemarker/backup lamp bulbsThe tail/stop/turn/sidemarker/backup lamp bulbs are located in the sameportion of the tail lamp a

2. Remove the bulb holder from thelamp assembly by depressing thesnaps.3. Pull the bulb straight out of thesocket and push in the new bulb.Install the

Replacing foglamp bulbs (if equipped)1. Make sure the foglamp switch isin the OFF position.2. From underneath the vehicle,remove splash shield and rot

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Rear window wiper/washer controlsFor rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select:2 — Normal spe

ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamp.Slide on rod featureThe visor will slide back and forthon

CENTER CONSOLE (IF EQUIPPED)Your vehicle may be equipped with a variety of console features. Theseinclude:1. Cupholders2. Tissue box holder (located o

Always keep the power point caps closed when not being used.A third auxiliary power point islocated on the rear side of thecenter console. The power p

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

Press and pull the window switchesto open and close windows.• Push down (to the first detent)and hold the switch to open.• Pull up (to the first deten

AUTOMATIC DIMMING INTERIOR REAR VIEW MIRROR(IF EQUIPPED)Your vehicle may be equipped withan interior rear view mirror whichhas an auto-dimming functio

Fold-away mirrorsPull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.Heated outside mirrors(if equipped)B

3. Press the SET + control andrelease it.4. Take your foot off the acceleratorpedal.5. The indicatorlight on theinstrument cluster will turn on.Note:•

Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET + controluntil you get to the desiredspeed,

Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal. This willnot erase your vehicle’spreviously set s

In any mode:• Press VOL + or - to adjust thevolume.Climate control featuresPress TEMP + or - to adjusttemperature.Press FAN + or - to adjust fanspeed.

Do not let children play with the panoramic Vista Roof娂 andpower sunshade or leave children unattended in the vehicle.They may seriously hurt themselv

To vent the panoramic Vista Roof娂: From the closed position, pressand release the TILT control. To vent the panoramic Vista Roof娂 fromany position, pr

Odometer/Trip odometerRefer to Gauges in the Instrument Cluster chapter.Distance to empty (DTE)Selecting this function from theINFO menu estimates app